Panasonic CS-XE9EKE Manuale utente

Marca: Panasonic

Modello: CS-XE9EKE

Tipo: Manuale utente

F565101

CS-XE9EKE CU-XE9EKE

CS-XE12EKE CU-XE12EKE

Manufactured by:

Panasonic HA Air-Conditioning (M) Sdn. Bhd.

Lot 2, Persiaran Tengku Ampuan, Section 21, Shah Alam Industrial Site,

40300 Shah Alam, Selangor, Malaysia.

Operating Instructions

Air Conditioner

and distribution is a violation of law.

ENGLISH Before operating the unit, read these operating instructions thoroughly and keep them for future reference. 2 ~ 17

ESPAÑOL Antes de utilizar la unidad, sírvase leer atentamente estas instrucciones de funcionamiento y conservarlas como futuro elemento

de consulta. 18 ~ 33

ITALIANO Prima di utilizzare l’unità si prega di leggere attentamente le istruzioni e di conservare questo opuscolo per potervi fare riferimento

in futuro. 34 ~ 49

NEDERLANDS Leest u voor het gebruik de instructie en bewaar deze om later te kunnen raadplegen. 50 ~ 65

PORTUGUÊS Antes de ligar a unidade, leia cuidadosamente este manual de utilização e guarde-o para futura referência. 66 ~ 81

EΛΛΗΝΙΚΆ Προτού θέσετε τη μονάδα σε λειτουργία, διαβάστε προσεκτικά αυτές τις οδηγίες χρήσης και φυλάξτε τις για μελλοντική αναφορά. 82 ~ 97

БЪЛГАРСКИ Преди да задействате климатика, прочетете внимателно инструкциите за употреба и ги запазете за бъдещи справки. 98 ~ 113

This symbol denotes

an action that is

PROHIBITED.

These symbols denote

actions that are

COMPULSORY.

■ Definition

Warning

Caution

To prevent personal injury,

injury to others, or property

damage, please observe the

following.

Incorrect operation due to

failure to follow instructions

may cause harm or damage,

the seriousness of which is

classiﬁ ed as below:

The instructions to be

followed are classiﬁ ed by

the following symbols:

Caution

Thank you for purchasing Panasonic Air Conditioner

• Aerate the room regularly.

• After long periods of use, make sure the installation rack is not damaged.

• Insert the power plug properly.

• Use the speciﬁ ed supply cord.

• If the supply cord is damaged, it must be

replaced by the manufacturer, its service

agent or similarly qualiﬁ ed persons in

order to avoid a hazard.

• Remove the batteries if the unit is not

going to be used for a long period of

time.

• New batteries of the same type must

be inserted following the polarity stated

to prevent malfunction of the remote

control.

• In case of emergency or abnormal

conditions (burning, unusual odour, etc),

turn off the power supply and unplug.

Warning

During Installation

• Do not share the same power outlet with

other equipment.

• Do not modify power cords.

• Do not use extension cords.

• Do not operate with wet hands.

• Do not operate or stop the unit by inserting

or pulling out the power plug.

• Do not insert your ﬁ ngers or other objects

into the indoor or outdoor unit.

• Do not attempt to repair the unit by

yourself.

• Do not use rechargeable (Ni-Cd) batteries.

• Keep the remote control away from infants

and small children to prevent them from

accidentally swallowing the batteries.

• Do not install, remove and reinstall the unit by yourself; improper installation will cause leakage, electric

shock or ﬁ re. Please consult an authorized dealer or specialist for the installation work.

• This equipment must be earthed and installed with ELCB. It may cause electrical shock or ﬁ re in case of

malfunction

During Operation

• Switch off the power supply and unplug

before cleaning or servicing.

• Turn off the power supply and unplug if

the unit is not used for a long period of

time.

• This air conditioner is equipped with

a built-in surge protective device.

However, in order to further protect your

air conditioner from being damaged by

abnormally strong lightning activity, you

may want to disconnect it from the power

supply. Do not touch the air conditioner

during lightning, it may cause electric

shock.

• Do not pull the cord to disconnect the

plug.

• Do not wash the unit with water, benzene,

thinner or scouring powder.

• Do not use for other purposes such as

preservation of food.

• Do not use any combustible equipment in

front of the airﬂ ow outlet.

• Do not sit or place anything on the indoor

or outdoor unit.

• Do not expose directly to cold air for a

long period.

• Ensure that the drainage pipe is connected properly. Otherwise, leakage may occur.

• Do not install the unit in a potentially explosive atmosphere.

During Installation

During Operation

SAFETY PRECAUTIONS

TABLE OF CONTENT

This sign warns of death

or serious injury.

This sign warns of injury

or damage to property.

SAFETY PRECAUTIONS, REGULATORY INFORMATION ........................................................................................................... 2~3

PRODUCT OVERVIEW .................................................................................................................................................................. 4~5

INTRO TO FILTER CLEANING ........................................................................................................................................................... 6

AUTO FILTER CLEANING, TIMER FILTER CLEANING ................................................................................................................ 7~8

MANUAL FILTER CLEANING ............................................................................................................................................................. 9

CHANGE FILTER CLEANING DEFAULT SETTING ......................................................................................................................... 10

AUTO, HEAT, COOL, DRY, VENTILATION ..................................................................................................................................11~12

FAN SPEED, AIR SWING ................................................................................................................................................................. 13

POWERFUL, QUIET, TIMER ...................................................................................................................................................... 14~15

CARE & MAINTENANCE ............................................................................................................................................................ 16~17

ENGLISH

Replacement or installation of power plugs shall be performed by authorized/qualiﬁ ed

personnel only.The wires in this mains lead are coloured in accordance with the

following code:

Wiring colour may vary depending on a country wiring code’s standard.

Terminals

wires

live

neutral

colours (GB Standard)

brown

blue

red

black

green-yellow

earth

green/yellow

■ Operation Condition

Use this air conditioner under the

following temperature range.

*DBT: Dry bulb temperature

*WBT: Wet bulb temperature

• This unit is still able to operate as a

cooler with outdoor temperature as

low as -15°C in a non-living room,

such as a computer room, with a

room temperature of 16°C or above,

and room humidity up to 80%.

• When the outdoor temperature drops

to -15°C, compressor will be cut off

and resume operation again once

the temperature rises to more than

-15°C.

REGULATORY INFORMATION

Battery disposal

The batteries must be recycled or disposed of properly.

“Instructions for end-user” for air conditioners:

nvironmental Requirements

End-of-Life Disposal

Note:

The illustrations in this manual

are for explanation purposes only

and may differ from the actual unit. It

is subjected to change without notice

for future improvement.

The appliance is not intended for use by young children or the inﬁ rm person without supervision. Young

children should be supervised to ensure that they do not play with the appliance.

This air conditioner bears the above mark, indicating that electrical equipment should not be disposed

of alongside general household waste. European Community countries (*), should have a dedicated

collection system for these products. Do not try to dismantle the system yourself as this could have harmful

effects on your health and on the environment as a result of incorrect waste handling. This dismantling

and disposal of refrigerant, oil and other parts must be done by a qualiﬁ ed installer in accordance with

relevant local and national regulations. Air conditioners must be treated at a specialized treatment facility

for re-use, recycling and recovery and should not be disposed of in the municipal waste stream. Please

contact your installer, dealer or local authority for more information. Penalties may also be applicable for

incorrect disposal of waste products, in accordance with national legislation.

*subject to the national law of each member state

Information on Disposal in other countries outside the European Union

This symbol is only valid in the European Union. If you wish to discard this product, please contact

your installer, dealer or local authority and ask for the correct method of disposal.

Temperature (°C)

Indoor

*DBT *WBT

COOLING

Maximum 32 23

Minimum 16 11

HEATING

Maximum 30 –

Minimum 16 –

Temperature (°C)

Outdoor

*DBT *WBT

COOLING

Maximum 43 26

Minimum -15 –

HEATING

Maximum 24 18

Minimum -15 –

■ About

PRODUCT OVERVIEW

Air inlet (rear)

Air outlet

Air inlet (side)

Outdoor Unit

Auto OFF/ON Button

Indoor Unit

Indicator

Receiver

Auto

OFF/ON

button

Filter cleaning

device

Airflow

direction

louver

Air filter

fastener

Movable

front panel*

Super alleru

buster filter

Filter cleaning

indication light

Air intake

Discharged air

• To operate the unit if the

remote control is misplaced or

malfunctioning.

Note:

* Movable front panel will open slightly for air intake purposes once the air conditioner operation starts.

Movable front panel will remain open during air conditioner operation. It will close automatically once the

air conditioner operation stops. In such a condition, do not interrupt the movable front panel movement

as this may cause malfunction or unit breakdown. The above condition does not apply for ﬁ lter cleaning.

Air filter

Step Action Mode

1 Press once. Automatic

Press and hold

until you hear

one beep, then

release.

Force

cooling

Repeat step 2.

Press and hold

until you hear

two beeps, then

release.

Normal

cooling

Repeat step 3.

Press and hold

until you hear

three beeps, then

release.

Force

heating

• To turn off, press the AUTO OFF/ON

button again.

ENGLISH

Remote Control

PRODUCT OVERVIEW

Troubleshooting - error code checking

■ About

Remote Control Preparation

• Make sure it is not obstructed.

• Maximum distances: 8m.

• Certain fluorescent lights may

interfere with signal transmission.

Please consult your nearest

authorized dealer.

Remote Control Signal

6. Press to conﬁ rm.

• Timer operation will be based on

current time set.

• The batteries can be used for

approximately 1 year.

5. Press to

set time.

1. Pull out the

cover.

Transmitter

LCD

display

Off/On

Cooling,

Auto,

Heating,

Dry mode

Quiet

operation

Ventilation

operation

Temperature

setting

Fan speed selection

Timer setting

Clock setting

Air conditioner reset

Check

Airflow

direction

adjustment

● In the event of an error, the unit will stop and the timer indicator will blink.

Notes:

• The unit may be operable (with 4 beeps)

on a limited basis, depending on the error.

1. Press for 5 seconds.

3. Press for 5 seconds to

quit checking.

2. Press until you hear beep sound,

then jot down the error code.

4. Turn the unit off and reveal the error

code to your nearest dealer.

Manual filter cleaning

operation

Timer filter cleaning setting

* For normal operation, the and buttons are not in use.

2. Insert AAA

or LR03 batteries.

3. Close the cover.

4. Press CLOCK.

Powerful

operation

INTRO TO FILTER CLEANING

■ About

Filter cleaning

Filter cleaning function helps to:

• Clean the filters automatically on a

regular basis.

• Avoid airflow blockage caused by

dusty filter.

• Prevent growth of mold inside the

unit.

• Improve heating/cooling effect that

saves energy consumption.

Aut

o F

ilter Cl

eaning

Filter Cleaning Device

• By default, filter cleaning will run automatically once the unit is turned off if the air

conditioner:

- Operates continuously for at least 2 hours and above, and

- Accumulative operation time is at least 2 hours and above.

• The filter surface is divided into rows. Each cleaning cycle will clean one row at a time.

The numbers of rows to be cleaned will be based on the air conditioner’s accumulative

operation time and model purchased. The following table is an example for model 1.5 HP.

Accumulative operation time

(<: less than)

Number of cleaning cycle

(1 cycle: < 4 minutes)

< 2 hours 0

2 hours and < 6 hours 2

6 hours and < 9 hours 3

9 hours and < 12 hours 4

12 hours and < 15 hours 5

15 hours and < 18 hours 6

18 hours and < 21 hours 7

21 hours and < 24 hours 8

• The number of cleaning cycle depends on the fan speed setting as well. The table above is

an example when the fan speed setting is HI. The number of cleaning cycle will be lesser if

the fan speed setting is lower.

• You can also set the filter cleaning manually. For details, see Timer Filter Cleaning and

Manual Filter Cleaning in the following pages.

Troubleshooting

● When the ﬁ rst air conditioner operation is initialized,

ﬁ lter cleaning will run one cycle automatically.

► This is a normal operation to make sure the ﬁ lter cleaning device is able

to move smoothly.

► Filter cleaning will not be terminated by pressing any of the remote

control buttons. Filter cleaning will stop by itself after operates for one

cycle.

ENGLISH

AUTO FILTER CLEANING

Auto F

ilter Cl

eaning

AUTO

• Filter cleaning will run automatically after the air conditioner operation stops (air conditioner is turned

off using remote control).

• After the filter cleaning is completed, the air conditioner operation will remain off.

AIR CONDITIONER TIMER

• Filter cleaning will run automatically after the air conditioner operation stops (air conditioner is turned

off by the air conditioner timer).

• After the filter cleaning is completed, the air conditioner operation will remain off.

Filter Cleaning Indicator

FORCE CLEANING

• Once the air conditioner operation time exceeds 24 hours, the unit is forced to run filter cleaning.

• After the filter cleaning is completed, the air conditioner operation will resume automatically.

• The ﬁ lter cleaning indicator light

will move to left or right when ﬁ lter

cleaning is in progress.

• Filter cleaning in progress will be

cancelled if:

- Certain button on the remote

control are pressed.

- The air conditioner main unit’s

movable front panel is lifted up.

- There is a power failure.

Troubleshooting

● Timer indicator is blinking and error code H51 is

revealed on the display.

► The ﬁ lter cleaning device is jammed because the ﬁ lter is not installed

correctly.

► The ﬁ lter cleaning device is malfunction.

●

Timer indicator is blinking and error code H52 is

revealed on the display.

► The ﬁ lter cleaning device is malfunction.

► Printed circuit board is malfunction.

Note :

• To reveal the error code, please refer to Product Overview’s troubleshooting-error code checking.

• The condition above does not affect the unit’s operation.

• In case of malfunction, please consult your nearest authorized dealer.

■ About

Filter cleaning

TIMER FILTER CLEANING

● To cancel ﬁ lter cleaning timer, press , then press

Press to set

cleaning

timer.

Press to turn

on cleaning

timer. ON is

shown on the

display.

Press to

conﬁ rm the

setting.

shown on

the display.

Press to

select

your desired

time.

■ About

• Filter cleaning timer can be set

to run at a specified time daily,

given that the air conditioner

accumulative operation time is at

least 30 minutes and above.

• Filter cleaning timer overrides

air-conditioner’s timer in any given

setting.

• Once filter cleaning timer starts, air

conditioner operation will stop. After

the filter cleaning is completed,

the air conditioner operation will

resume automatically.

• To reveal filter cleaning timer start

time:

Press

• To restore the filter cleaning timer

after power is resumed:

Press , then press .

• To return to normal display / exit:

Press

or close the remote

control cover.

■ Hint

• Set the ﬁ lter cleaning timer to run

at an appropriate time to avoid any

interruption during normal operation.

Timer Filter Cleaning

ENGLISH

MANUAL FILTER CLEANING

● Press to cancel manual ﬁ lter cleaning.

■ About

• Press once to run a

comprehensive ﬁ lter cleaning.

• A comprehensive ﬁ lter cleaning may

take less than an hour to complete.

• When is pressed, this operation

has the highest priority over other

operation modes. The air conditioner

operation will stop. After the ﬁ lter

cleaning is completed, the air

conditioner operation will resume

automatically.

■ Hint

• After extended non-use, it is

recommended to manually run

ﬁ lter cleaning before air conditioner

operation is initialized.

Press to clean

the ﬁ lter

manually.

Troubleshooting

● The ﬁ lter cleaning device stops half way in the

middle of the main unit.

► To return the ﬁ lter cleaning device to the original position, press and

hold

for more than 5 seconds.

► To change the ﬁ lter cleaning device from right side (original position) to

left side, press and hold for more than 5 seconds, then press .

Manual Filter Cleaning

CHANGE FILTER CLEANING

DEFAULT SETTING

■ Hint

• Manual ﬁ lter cleaning is operable

by pressing

. For detail, see

manual ﬁ lter cleaning page.

■ Setting

• To disable the ﬁ lter cleaning

permanently, follow steps 1 to 3 as

shown below.

Disable Filter Cleaning

Press and hold for more than

20 seconds. ON will blink on

the display.*

Press to select OFF.

Press to conﬁ rm the setting.

CLEANING will disappears

from the display.

• Auto and timer ﬁ lter cleaning are no

longer valid.

• Select ON in step 2 above to

enable ﬁ lter cleaning.

• As a default setting, ﬁ lter cleaning will run automatically once the air conditioner unit is turned off.

Press and hold until you

hear 3 beeps (about 11

seconds).

Press once.

You will hear 1 beep.*

Press to select your desired ﬁ lter cleaning setting:

Auto OFF/

ON button.

Press 3 times until you

hear 3 continuous beeps.*

When you hear Setting

1 beep • Filter cleaning will run automatically after the air conditioner

operation stops (air conditioner is turned off using remote control).

• After the ﬁ lter cleaning is completed, the air conditioner operation

will remain off.

2 beeps ** • Filter cleaning will run automatically before the air conditioner

operation starts (air conditioner is either turned on using remote

control or turned on by the air conditioner timer).

• After the ﬁ lter cleaning is completed, the air conditioner operation

will start automatically.

3 beeps ** • Filter cleaning will run automatically before the air conditioner

operation starts (air conditioner is turned on using remote control).

• After the ﬁ lter cleaning is completed, the air conditioner operation

will start automatically.

1 long beep

(default setting)

• Filter cleaning will run automatically after the air conditioner

operation stops (air conditioner is either turned off using remote

control or turned off by the air conditioner timer).

• After the ﬁ lter cleaning is completed, the air conditioner operation

will remain off.

* Use a sharp end object to press this button.

** The setting is valid only if the following conditions are fulﬁ lled:

1. The air conditioner is turned off for at least 3 minutes.

2. The air conditioner has operated continuously for at least 2 hours in previous operation.

ENGLISH

AUTO, HEAT, COOL, DRY

● , and operations are available in all modes.

●

Press

to stop the operation.

Select your

desired

operation.

Select your

desired

temperature.

(16°C~30°C)

■ Operation Details

COOL - Cooling Operation

• Enjoy cool air at your desired

temperature.

DRY - Soft Dry Operation

• Keeps your environment

dehumidiﬁ ed by running a very

gentle cooling operation.

• During soft dry operation, the

indoor fan operates at low fan

speed.

AUTO - Automatic Operation

• Unit selects the operation mode

according to temperature setting,

outdoor and room temperature.

• The power indicator blinks during

operation.

• Operation mode is reselected

every 30 minutes.

■ Hint

• A temperature setting 1°C higher

in cooling operation or 2°C lower in

heating operation than the desired

temperature equates to a 10%

power saving.

Troubleshooting

● Mist emerges from indoor unit. ► Condensation effect due to cooling process.

●

Heating/cooling operation does not work.

► Ensure temperature is set correctly.

► Make sure windows and doors are closed.

► Make sure inlet and outlet vents are cleared.

● Water ﬂ owing sound during operations. ► Cause by refrigerant ﬂ ow inside the unit.

• In heating mode, it takes a while

for the unit to warm up. The

power indicator blinks during this

operation.

HEAT - Heating Operation

VENTILATION

Select your

desired

ventilation

setting.

■ Operation Details

• To aerate the room.

• As a default setting, ventilation will

be turned on automatically once the

air conditioner operation starts.

• Operates simultaneously with Auto/

Cooling/Heating/Drying operation.

• Press

repeatedly to select

your desired ventilation setting.

Auto/Cooling/Heating/Drying

operation remains as normal

regardless of ventilation setting.

• When is pressed, all of the air

conditioner operations are turned

off.

• Ventilation operates independently.

• Ventilation can be turned on when

the air conditioner is in non-

operation mode.

• Fan speed in this setting remains as

AUTO.

• Press

to turn off the ventilation

operation.

Troubleshooting

● Timer indicator is blinking and error code H50 is

revealed on the display.

► Ventilation fan motor may be locked due to piles of dust accumulated in

the ventilation area and fails to discharge.

► Printed circuit board is malfunction.

► Ventilation fan motor is malfunction.

Note :

• To reveal the error code, please refer to Product Overview’s troubleshooting-error code checking.

• The condition above does not affect the unit’s operation.

• In case of malfunction, please consult your nearest authorized dealer.

Low Ventilation

No Ventilation

Auto Ventilation

VENTILATION : Simultaneous

Operation

VENTILATION : Independent

Operation

ENGLISH

■ Operations Details

• There are 5 fan speeds, as well as

automatic*.

* For automatic fan speed, the

speed of the indoor fan is

automatically adjusted according

to the operation.

FAN SPEED, AIR SWING

Troubleshooting

● The room has a peculiar odour. ► This may be a damp smell emitted by the wall, carpet, furniture or

clothing.

● Indoor fan stops occasionally during automatic fan

speed setting.

► This helps to remove the surrounding odours.

● Indoor fan stops occasionally during heating

operation.

► To avoid unintended cooling effect.

AIR SWING

• If automatic vertical airﬂ ow direction

has been set, the louvers swing up

and down automatically.

• For HEATING operation, the air

blows horizontally for a while, then

starts to blow downwards.

• If automatic horizontal airﬂ ow

direction has been set, the louvers

swing left and right automatically.

• For HEATING operation, the airﬂ ow

louvers start to swing left/right after

the temperature rises.

• Keeps the room ventilated.

• There are 5 options for vertical/

horizontal airﬂ ow direction.

• Do not adjust the vertical and

horizontal louvers by hand.

Press to

select

fan speed

Adjust the airﬂ ow

direction louver.

POWERFUL, QUIET

● and operations are not able to operate at the

same time.

● and operations could be cancelled by pressing

the respective button again.

To enable

quiet

operation.

To enable

powerful

operation.

■ Operations Details

• To reach the desired set temperature

quickly.

• To provide a quiet surrounding.

■ Hint

• To reduce power consumption

during cooling operation, close the

curtains to prevent the sunlight and

heat from coming in.

Troubleshooting

● Noisy during operation. ► The unit may have been installed at an incline, or the movable front

panel is not closed properly.

● Operation is delayed a few minutes after restart. ► The delay is a protection to the unit’s compressor.

● Outdoor unit emits water/steam. ► Condensation or evaporation occurs on pipes.

ENGLISH

■ Operation Details

TIMER

• The timer allows you to turn the air

conditioner on or off automatically.

• The unit may start in preliminary

operation before the actual set time

when ON timer has been set.

• The set timer repeats daily once

set.

• If there is a power failure, you can

restore the previous setting (once

power is resumed) by pressing the

button.

• If the timer is cancelled, press

to restore the previous setting.

● The timer is valid only when the clock is set correctly.

● You can set your preferred time for ON and OFF timers. The

unit will turn on or off automatically.

● To cancel ON or OFF timer, press

or , then press

To select ON

or OFF timer.

To select

your desired

time.

To conﬁ rm

the setting.

Troubleshooting

● Timer indicator always on. ► The timer setting repeats daily once set.

● Power indicator blinks before the unit is switched on. ► This is a preliminary step in preparation for the operation when the ON

timer has been set.

● Remote control does not work. ► The batteries are inserted incorrectly or need replacing.

● The unit does not work. ► The circuit breaker is tripped or the timer is set incorrectly.

■ Hint

• To dim the indicator display:

Press and

hold for 5

seconds.

To cancel,

press

the

again for 5

seconds.

■ Hint

• Please consult your nearest

authorized dealer for seasonal

inspection.

CARE & MAINTENANCE

• Wipe the unit gently with a soft, dry

cloth.

INDOOR UNIT

• Do not remove the movable part

from the front panel.

• Soak cloth/sponge in lukewarm

water with detergent. Squeeze it

dry and wipe the panels. Repeat

same step again, but this time soak

cloth in lukewarm water without any

detergent.

• Do not dry the parts with a hair

dryer, a stove, or under direct

sunlight.

• Dry the parts under the shades.

MOVABLE FRONT PANEL &

TOP GRILL

■ Washing Instructions

• Do not use benzene, thinner, bleach

or scouring powder.

• Use only soaps (

≃

pH7) or neutral

household detergent .

• Do not use water hotter than 40°C.

witch off the power supply

before cleaning

Raise and pull to remove.

Wash gently and dry.

MOVABLE FRONT PANEL

Push up and pull to remove.

Wash gently and dry.

TOP GRILL

Wipe gently.

INDOOR UNIT

■ For extended non-use

• Activate heating for 2~3 hours to thoroughly dry the unit.

• Turn off the power supply and unplug.

• Remove the remote control batteries.

Top air ﬁ lter

Super alleru-

buster ﬁ lter

Front air ﬁ lter

ENGLISH

CARE & MAINTENANCE

witch off the power supply

before cleaning

REMOVE THE FRONT AIR FILTER

Push upwards to unlock the

air ﬁ lter fastener.

REMOVE THE TOP AIR FILTER

REMOVE THE SUPER ALLERU-BUSTER FILTER

• Wash any dusty ﬁ lter whenever

necessary.

• Wash/rinse the ﬁ lter gently with

water to avoid damage to the unit

surface.

• Replace any damage ﬁ lters.

AIR FILTER

■ Hints

• For best performance, it is

recommended to install the air

conditioner in a room away from the

kitchen.

• Air conditioner installed near a

kitchen is more likely to run a risk of

damaging the air conditioner ﬁ lter

caused by oily air and dust. A ﬁ lter

exposed to excessive oily air cannot

be cleaned thoroughly with auto ﬁ lter

cleaning.

● To reinstall the ﬁ lter after cleaning is completed, repeats the

illustration steps in a backward order, from step 4 to step 1.

■ About

• To make sure the front air ﬁ lter is

inserted correctly:

1. Press both hollow parts until the

projections are clicked.

2. Push downwards to lock the air

ﬁ lter fastener.

• To make sure the ﬁ lter cleaning

device is able to move smoothly:

FILTER INSTALLATION

Press both hollow parts with

ﬁ ngers and pull out the air

ﬁ lter.

Pull the air ﬁ lter towards you.

Detach the ﬁ lter gently.

Press and

hold for 10

seconds.

Projections

Air filter fastener

• Vacuum the ﬁ lter whenever

necessary.

• Replace the ﬁ lter every 10 years or

purchase the replacement ﬁ lter if it

is damaged.

Part no: CZ-SA15P

SUPER ALLERU-BUSTER

114

SEASONAL INSPECTION AFTER EXTENDED NON-USE:

• Checking of remote control batteries.

• No obstruction at inlet and outlet vents.

• After 15 minutes of operation, it is normal to have the following temperature difference between inlet and outlet vents:

Cooling: ≥ 8°C

Heating: ≥ 14°C

INSPECCIÓN PERIÓDICA TRAS NO UTILIZAR LA UNIDAD DURANTE UN TIEMPO PROLONGADO

DE TIEMPO:

• Veriﬁ que las pilas del mando a distancia.

• Compruebe que las tomas de entrada y salida de aire no están obstruidas.

• Tras 15 minutos de funcionamiento, es normal que se produzca la siguiente diferencia de temperatura entre las tomas de entrada y

salida de aire:

Enfriamiento: ≥ 8°C

Calentamiento: ≥ 14°C

ESEGUIRE L’ISPEZIONE STAGIONALE DOPO UN PERIODO DI INATTIVITÀ PROLUNGATO:

• Controllo delle batterie del telecomando.

• Nessuna ostruzione alle bocchette di ingresso ed uscita dell’aria.

• Dopo 15 dall’avvio, è normale che vi sia una differenza di temperatura tra l’aria in ingresso e le aperture di uscita:

Raffreddamento: ≥ 8°C

Riscaldamento: ≥ 14°C

SEIZOENINSPECTIE NA LANGDURIGE INACTIVITEIT:

• Controleer de batterijen van de afstandsbediening.

• Controleer de inlaat- en uitlaatopeningen op obstructies.

• Het is normaal dat na 15 minuten gebruikstijd het temperatuurverschil tussen de inlaat- en uitlaatopeningen als volgt is:

Bij koelen: ≥ 8°C

Bij verwarmen: ≥ 14°C

INSPECÇÃO SAZONAL APÓS UM PERÍODO DE INACTIVIDADE PROLONGADO:

• Veriﬁ que as pilhas do controlo remoto.

• Os orifícios de entrada e saída devem estar desobstruídos.

• Após 15 minutos de funcionamento, é normal que a seguinte diferença de temperatura se veriﬁ que entre os orifícios de entrada e saída:

Arrefecimento: ≥ 8°C

Aquecimento: ≥ 14°C

ΕΠΟΧΙΑΚΗ ΕΠΙΘΕΩΡΗΣΗ ΜΕΤΑ ΑΠΟ ΠΑΡΑΤΕΤΑΜΕΝΗ ΠΕΡΙΟΔΟ ΠΟΥ ΔΕΝ ΕΧΕΙ

ΧΡΗΣΙΜΟΠΟΙΗΘΕΙ:

• Έλεγχος των μπαταριών του τηλεχειριστήριου.

• Έλεγχος αν παρεμποδίζονται οι αεραγωγοί εισόδου και εξόδου αέρα.

• Μετά από 15 λεπτά λειτουργίας, είναι φυσιολογικό να έχετε τις παρακάτω διαφορές θερμοκρασίας μεταξύ των αγωγών εισόδου και

εξόδου:

Ψύξη: ≥ 8°C

Θέρμανση: ≥ 14°C

СЕЗОНЕН ПРЕГЛЕД СЛЕД ПРОДЪЛЖИТЕЛНО НЕИЗПОЛЗВАНЕ:

• Проверка на батериите на дистанционното управление.

• Премахване на евентуални прегради на входните и изходните вентилационни отвори.

• След 15 минути работа е нормално да има следната температурна разлика между входните и изходните вентилационни отвори:

Охлаждане: ≥ 8°C

Отопляване: ≥ 14°C

115

ИЗКЛЮЧЕТЕ ЗАХРАНВАНЕТО и се ОБАДЕТЕ на оторизирания дистрибутор при следните

условия:

• Необичаен звук по време на работа. • Прекъсвачът на ел. верига се изключва често.

•

Вода/чужди частици са попаднали в дистанционното управление.

• Захранващият кабел се загрява необичайно.

• Изтича вода от Вътрешния уред. • Копчетата или бутоните не функционират правилно.

КРИТЕРИИ ЗА ПОВРЕДА

ΔΙΑΚΟΨΤΕ ΤΗΝ ΠΑΡΟΧΗ ΡΕΥΜΑΤΟΣ και ΚΑΛΕΣΤΕ κάποιο εξουσιοδοτημένο κατάστημα στις

παρακάτω περιπτώσεις:

• Θόρυβος κατά τη λειτουργία. • Συχνή πτώση του ασφαλειοδιακόπτη.

• Είσοδος νερού/σωματιδίων στο τηλεχειριστήριο. • Αποσυνδέστε την παροχή ρεύματος.

• Διαρροή νερού από την εσωτερική μονάδα. • Οι διακόπτες ή τα πλήκτρα δε λειτουργούν σωστά.

ΠΕΡΙΠΤΩΣΕΙΣ ΠΟΥ ΔΕΝ ΑΝΤΙΜΕΤΩΠΙΖΟΝΤΑΙ ΑΠΟ ΤΟ ΧΡΗΣΤΗ

TURN OFF POWER SUPPLY and CALL Authorized Distributor under the following conditions:

• Abnormal noise during operation. • Circuit breaker switches off frequently.

• Water/foreign particles have entered the Remote Control. • Power cord becomes unnaturally warm.

• Water leak from Indoor unit. • Switches or buttons are not functioning properly.

NON SERVICEABLE CRITERIAS

DESLIGUE O SISTEMA DE ALIMENTAÇÃO e CONTACTE o Distribuidor Autorizado nas

seguintes condições:

• Ruído anormal durante o funcionamento. • Os interruptores do disjuntor desligam-se

• Água/partículas estranhas entraram no controlo remoto. frequentemente.

• Fuga de água da unidade interior. • O ﬁ o distribuidor de corrente aquece de forma anormal.

• Os interruptores ou botões não estão a funcionar

devidamente.

CRITÉRIOS SEM MANUTENÇÃO

SCHAKEL DE STROOMTOEVOER UIT en RAADPLEEG een erkend verdeler onder de volgende

omstandigheden:

• Een abnormaal lawaai tijdens de werking. • De zekering springt regelmatig uit.

• Water of vreemde deeltjes zijn in de afstandsbediening • De stroomdraad wordt onnatuurlijk warm.

binnengedrongen. • De schakelaars of knoppen werken niet zoals het hoort.

• Er lekt water uit de binneneenheid.

OMSTANDIGHEDEN WAARIN U HULP MOET INROEPEN

Se si veriﬁ ca una delle seguenti condizioni, spegnere immediatamente l’interruttore

generale e chiamare il rivenditore autorizzato:

• Durante il funzionamento si sentono rumori anomali. • L’interruttore salvavita scatta frequentemente.

• Penetrazione di acqua o di corpi estranei nel telecomando. • Il cavo di alimentazione su surriscalda in modo

• L’unità interna perde acqua. anomalo.

• Funzionamento anomalo di interruttori o pulsanti.

FUNZIONAMENTO ANOMALO

Si se dan las siguientes circunstancias, CORTE LA ALIMENTACIÓN y LLAME al distribuidor

autorizado

• Si escucha ruidos extraños durante el funcionamiento • Si el interruptor del circuito salta frecuentemente

• Si entra agua o elementos extraños en el mando a distancia • Si el cable de alimentación y el enchufe se recalientan

• Si hay escapes de agua de la unidad interior • Los interruptores o los botones no funcionan correctamente

NO UTILICE LA UNIDAD SI...

Matsushita Electric Industrial Co., Ltd.

Web Site: http://www.panasonic.co.jp/global/

F565101

Printed in Malaysia

OPSC0601-02

Panasonic CS-XE9EKE Manuale utente

Marca: Panasonic

Modello: CS-XE9EKE

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: Panasonic CS-XE9EKE User manual

Panasonic CS-XE9EKE Manuale utente

Panasonic CS-XE9EKE Manuale utente

in altre lingue

Documenti correlati

Altri documenti