Explore Scientific Professional WIFI Weather Centre 7in1 Manuale del proprietario

INDEX

HISTORY

CHANNEL

MAX

MIN

Art.No.: WSX3001

Weather station • Stazione meteo • Wetterstation • Station météo • Estación meteorológica

7-in-1 WiFi Advanced

Professional Weather Station

EN

INSTRUCTION MANUAL ............... 2

IT

ISTRUZIONI PER L’USO ...............34

DE

BEDIENUNGSANLEITUNG ............ 68

FR

MODE D'EMPLOI .......................102

ES

MANUAL DE INSTRUCCIONES ...136

2

EN

INSTRUCTION MANUAL

ABOUT THIS INSTRUCTION MANUAL

These operating instructions are to be considered a component of the device.

Please read the safety instructions and the operating instructions carefully before use.

Keep these instructions for renewed use at a later date. When the device is sold or given to someone else, the

instruction manual must be provided to the new owner/user of the product.

The device is intended only for indoor use.

This symbol represents a warning. To ensure safe use, always adhere to the instructions described in this

documentation.

This symbol is followed by a user’s tip.

GENERAL WARNINGS

• Risk of electric shock — This device contains electronic components that operate via a power source

(batteries). Children should only use the device under adult supervision. Only use the device as described

in the manual; otherwise, you run the risk of an electric shock.

• Choking hazard — Children should only use the device under adult supervision. Keep packaging

material, like plastic bags and rubber bands, out of the reach of children, as these materials pose a

choking hazard.

• Risk of chemical burn — Keep batteries out of the reach of children! Make sure you insert the batteries

correctly. Leaking battery acid can lead to chemical burns. Avoid contact of battery acid with skin, eyes

and mucous membranes. In the event of contact, rinse the aected region immediately with a plenty of

water and seek medical attention.

• Risk of re/explosion — Do not expose the device to high temperatures. Use only the recommended

batteries. Do not short-circuit the device or batteries, or throw them into a re. Excessive heat or improper

handling could trigger a short-circuit, a re, or an explosion.

• Do not disassemble the device. In the event of a defect, please contact your dealer. The dealer will

contact the Service Centre and can send the device in to be repaired, if necessary.

• Use only the recommended batteries. Always replace weak or empty batteries with a new, complete set

of batteries at full capacity. Do not use batteries from dierent brands or with dierent capacities. The

batteries should be removed from the unit if it has not been used for a long time.

SCOPE OF DELIVERY

Base station, 7-in-1 Multisensor, Thermo-Hygro Indoor sensor, AC/DC adapter (5V)

BEFORE YOU BEGIN

• We recommend using alkaline batteries. If temperatures regularly fall below 0°C (32°F), we recommend

using lithium batteries.

• Avoid using rechargeable batteries. (Rechargeable batteries cannot maintain correct power

requirements.)

• Insert batteries before rst use, matching the polarity in the battery compartment. Connect the AC/DC

adapter with the Base station and insert 3x AAA batteries as backup power. 3x AA batteries are required

for the 7-in-1 Multisensor and 2x AA batteries for the Thermo-Hygro indoor sensor.

3

EN

TABLE OF CONTENTS

ABOUT THIS INSTRUCTION MANUAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

GENERAL WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SCOPE OF DELIVERY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

CONSOLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

LCD DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

WIRELESS INDOOR HYGRO-THERMO SENSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

WIRELESS 7-IN-1 SENSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

INSTALLATION AND SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

INSTALL WIRELESS 7-IN-1 SENSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

INSTALL WIRELESS INDOOR SENSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

SETUP THE CONSOLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

SYNCHRONIZING ADDITIONAL WIRELESS SENSOR(S) (OPTIONAL) . . . . . . . . . . . . . . . . . . . . 10

POINTING THE WIRELESS 7-IN-1 SENSOR TO SOUTH . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

CREATE WEATHER SERVER ACCOUNT & SETUP WI-FI CONNECTION . . . . . . . . . . . . . . . . . . . . . .11

CREATE WEATHER UNDERGROUND ACCOUNT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

CREATE WEATHERCLOUD ACCOUNT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

SETUP WI-FI CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

SETUP THE WEATHER SERVER CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

ADVANCE SETTING IN WEB INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

VIEW YOUR WEATHER DATA IN WUNDERGROUND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

VIEW YOUR WEATHER DATA IN WEATHERCLOUD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

FIRMWARE UPDATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

OTHER SETTING & FUNCTIONS OF THE CONSOLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

MANUAL CLOCK SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

MOON PHASE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

SUNRISE & SUNSET TIME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

SETTING ALARM TIME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

ACTIVATING ALARM AND TEMPERATURE PRE-ALARM FUNCTION . . . . . . . . . . . . . . . . . . . . . 19

TEMPERATURE / HUMIDITY FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

TREND INDICATOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

WIND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

WEATHER INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

WEATHER FORECAST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

BAROMETRIC PRESSURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

RAIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

LIGHT INTENSITY, UV INDEX & SUNBURN TIME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

MAX / MIN DATA RECORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

PAST 24 HOURS HISTORY DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

WEATHER ALERT SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

BACKLIGHT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

DISPLAY CONTRAST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

BATTERY REPLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

WIRELESS 7-IN-1 SENSOR MAINTNANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

TROUBLESHOOT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

CONSOLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

WIRELESS 7-IN-1 SENSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

WIRELESS THERMO-HYGRO INDOOR SENSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

EC DECLARATION OF CONFORMITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

FCC DECLARATION OF CONFORMITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

NOTES ON CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

DISPOSAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

WARRANTY & SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

4

INTRODUCTION

Thank you for selecting the 7-in-1 WiFi Advanced Professional Weather Station. This system gathers

and automatically uploads accurate and detail weather data to Weather Underground and Weathercloud

website - the famous weather service which allows weather observers to upload their local weather data with

automated personal weather stations (PWS) - at which you can access and upload your weather data freely.

This product oers professional weather observers or serious weather enthusiasts robust performance with

a wide range of options and sensors. You will get your own local forecast, high/lows, totals and averages for

virtually all weather variables without using a PC.

The 7-in-1 sensor which measures outdoor temperature, humidity, wind, rain UV and light together with up to

7 individual temperature humidity sensors, which can add to a sensor array of maximum 7 units continually,

transmits weather data to the console. Both sensors are fully assembled and calibrated for your easy

installation. They send data at a low power radio frequency to the console from up to 150m/450 feet away

(line of sight).

In the console, high-speed processors are embedded to analyze the received weather data and these real-

time data can be published to Wunderground.com and weathercloud.net through your home WiFi router.

The console can also synchronize with internet time server to show high precision time and for its weather

data time stamp. The color LCD display shows informative weather readings with advanced features, such

as high/low alert alarm, dierent weather index, and MAX/MIN records. With calibration, sunrise / sunset and

moon phase features, this system is truly a remarkably personal yet professional weather station for your

own backyard.

NOTE:

This instruction manual contains useful information on the proper use and care of this product. Please read

this manual through to fully understand and enjoy its features, and keep it handy for future use.

OVERVIEW

CONSOLE

WI-FI

SENSOR REFRESH ALERTALARMCLOCK

SET

RESET

OFF LO HI

DC 5V 1A

ALARM / SNOOZEBARO WIND SUN RAIN

6

7

8

9

10

11

13

12

20

22

23

17

16

15

14

19

18

21

3 4 521

1. [ BARO ] key

2. [ WIND ] key

3. [ ALARM/SNOOZE ] key

4. [ SUN ] key

5. [ RAIN ] key

6. LCD display

7. [

/ ] key

8. [ INDEX /

] key

9. [ HISTORY ] key

10. [ MAX / MIN ] key

11. [ CHANNEL ] key

12. [ CLOCK SET ] key

13. Wall mounting holder

14. [ REFRESH ] key

15. [ SENSOR / WI-FI ] key

16. [ RESET ] key

17. [ °C / °F ] key

18. [ ALARM ] key

19. [ ALERT ] key

20. [ OFF / HI / LO ] slide

switch

21. Battery door

22. Table stand

23. Power jack

5

EN

LCD DISPLAY

1

2 3

4

5 6

7

8 9

10 11

Display section:

1. Outdoor temperature & humidity

2. Wind direction & speed

3. Indoor (Ch) temperature & humidity

4. Weather index

5. UV index & light intensity (SUN)

6. Weather forecast

7. Calendar & moon phase

8. Time / alarm

9. Barometer

10. Sunrise & sunset time

11. Rainfall & Rain rate

WIRELESS INDOOR HYGRO-THERMO SENSOR

1 2

3

4

5

1. Transmission status LED

2. Wall mounting holder

3. Channel slide switch

4. [ RESET ] key

5. Battery compartment

6

WIRELESS 7-IN-1 SENSOR

7

8

9

6

1

2

3

4

5

10

11

12

13

1. Wind vane

2. Wind cups

3. Antenna

4. Radiation shield

5. Thermo-hygro sensor

6. Mounting parts (t for 35 ~40mm diameter

pole)

7. Battery door

8. [ RESET ] key

9. Transmission status LED

10. Bubble level gradienter

11. Rain collector

12. UV / light sensor

13. Solar panel

7

EN

INSTALLATION AND SETUP

Your console can pair up with one wireless 7-in-1 outdoor sensor and up to 7 other wireless

sensors like Thermo/Hygro (ST2001H), Pool/Spa (SP60010) or Soil sensor (SM60020) (sold

separately).

INSTALL WIRELESS 7-IN-1 SENSOR

Your wireless 7-IN-1 sensor measures wind-speed, wind-direction, rainfall, UV, light intensity,

temperature and humidity for you. It’s assembled and calibrated for your easy installation.

INSTALL BATTERIES

Unscrew the battery door at bottom of unit and insert the

batteries according to the +/- polarity indicated. Screw the

battery door compartment on tightly.

NOTE:

- Ensure the water tight O-ring is properly aligned in

place to ensure water resistant.

- The red LED will begin ashing every 12 seconds.

Screw

location

3 x AA

batteries

MOUNTING KIT INSTALLATION

1. U-bolt x 2 2. Pole mounting

clamps x 4

3. Flat washers

x 4

4. Hex nuts

x 4

5. Stainless steel

pole

Note:

Stainless steel pole

placed under the egg

tray, please check before

disposal of the packaging.

Step 1:

Plug the stainless steel pole into

the sensor's mounting hole and

tighten the screws.

Note:

Please make sure that the sensor

has new batteries installed and is

paired up with the console.

Screws

8

Step 2:

Fasten the stainless steel pole on

your x pole (purchase separately)

with U-bolts, pole mounting clamps

and nuts.

Fixed pole

(not included)

MOUNTING POLE AND DIRECTION ALIGNMENT

Install the wireless 7-IN-1 sensor in an open

location with no obstructions above and around the

sensor for accurate rain and wind measurement.

Install the sensor with the smaller end facing the

North to properly orient the wind direction vane.

Secure the mounting stand and bracket (included)

to a post or pole, and allow minimum 1.5m off the

ground.

Point to

NORTH

1.5 meter

off the

ground

Fixed pole

package not

included

Add rubber

pad before

mounting on

pole or post

Install the wireless 7-IN-1 sensor in an open location

with no obstructions above and around the sensor for

accurate rain and wind measurement. Install the sensor

with the smaller end facing the North to properly orient

the wind direction vane. Secure the mounting stand and

bracket (included) to a post or pole, and allow minimum

1.5m o the ground.

Add rubber

pad before

mounting on

pole or post

1.5 meter

o the

ground

Fixed pole

(not included)

Point to

NORTH

9

EN

Step 2:

Fasten the stainless steel pole on

your x pole (purchase separately)

with U-bolts, pole mounting clamps

and nuts.

Fixed pole

(not included)

MOUNTING POLE AND DIRECTION ALIGNMENT

Install the wireless 7-IN-1 sensor in an open

location with no obstructions above and around the

sensor for accurate rain and wind measurement.

Install the sensor with the smaller end facing the

North to properly orient the wind direction vane.

Secure the mounting stand and bracket (included)

to a post or pole, and allow minimum 1.5m off the

ground.

Point to

NORTH

1.5 meter

off the

ground

Fixed pole

package not

included

Add rubber

pad before

mounting on

pole or post

Install the wireless 7-IN-1 sensor in an open location

with no obstructions above and around the sensor for

accurate rain and wind measurement. Install the sensor

with the smaller end facing the North to properly orient

the wind direction vane. Secure the mounting stand and

bracket (included) to a post or pole, and allow minimum

1.5m o the ground.

Add rubber

pad before

mounting on

pole or post

1.5 meter

o the

ground

Fixed pole

(not included)

Point to

NORTH

INSTALL WIRELESS INDOOR SENSOR

1. Remove the battery door of the sensor.

2. Use the channel slide switch to set the channel number for the

sensor (e.g. Channel 1)

3. Insert 2 x AA size batteries into the battery compartment and close

the battery door according to the polarity information marked on the

battery compartment.

4. The sensor is in synchronization mode, and can be registered to the

console within the next few minutes. The transmission status LED

will begin to ash every 1 minute.

NOTE:

- If you need to re-assign the sensor channel, slide the channel slide switch to the new channel

position. For the new channel number to be eective, press [ RESET ] key on the sensor.

- Avoid placing the sensors in direct sunlight, rain or snow.

- To avoid the sensor/s and console pairing failure during new console setup, please power up

the sensor/s rst, and then press [ RESET ] key on the main unit (no need on sensors).

PLACING THE WIRELESS INDOOR SENSOR

Place a screw on the wall that you wish to hang the sensor on.

Hang the sensor onto the screw by the wall mounting holder. You

can also place the sensor on a table by itself.

SETUP THE CONSOLE

POWER UP THE CONSOLE

1. Plug the adapter provided to the power jack at the back of the console.

2. Once the console is turned on, all the segments of the LCD will be shown momentarily.

3. The console will automatically enters sensor synchronization mode and AP mode (refer to

SETUP WI-FI CONNECTION).

NOTE:

If no display appears on the LCD after you plug the adaptor, press [ RESET ] key by using a

pointed object.

SYNCHRONIZING WIRELESS 7-IN-1 SENSOR AND INDOOR SENSOR(S)

Immediately after power up, while still in Synchronization mode, the 7-in-1 sensor and Indoor

Sensor can be paired to the console automatically. Once your sensors are paired up, the

sensors' signal strength indicator and weather reading will appear on your console display.

BACKUP BATTERY

Backup batteries are used to keep time-sensitive information on the console’s memory during

power failure. These include:

- Time & Date, Alarm Time, Max/Min & Past 24 hours weather records, Alert setting values,

Sensor(s) channel history, and Units

10

1. Remove the battery door of the console.

2. Insert 3 new AAA batteries as per the polarity indicated,

3. Replace the battery door.

BUILT-IN MEMORY

The console has built-in FLASH memory that holds the vital settings. These include:

- Time Zone, DST status, Time SYNC status, WI-FI and Weather server setting, Latitude /

Longitude, Hemisphere setting, Calibration values, and Sensor ID of paired sensor(s)

RESET AND FACTORY HARD RESET

To reset the console and start again, press the [ RESET ] key once

To hard reset the console and resume factory settings, press and hold the [ RESET ] key for 6

seconds

RESYNCHRONIZE SENSORS

Press the [ SENSOR / WI-FI ] key once for the console to enter sensor Synchronization

mode, and the console will re-register all the sensors that have already been registered to the it

before. i.e. the console will not lose the connection of the sensors that you’d paired up before.

CHANGING BATTERIES AND MANUAL PAIRING OF SENSOR

Whenever you changed the batteries of the wireless indoor or 7-in-1 weather sensor, re-

synchronization must be done manually.

1. Change all the batteries to new ones in the sensor.

2. Press [ SENSOR / WI-FI ] key on the console to enter sensor synchronization mode.

3. Press [ RESET ] key on the wireless indoor or 7-in-1 weather sensor.

SYNCHRONIZING ADDITIONAL WIRELESS SENSOR(S) (OPTIONAL)

The console can support up to 7 additional wireless sensors.

1. Press the [ SENSOR / WI-FI ] key once on the console to enter synchronization mode.

2. Press the [ RESET ] key on the new sensor, and wait for a few minutes for the new sensor

to paired to the console.

NOTE:

- Channel number of the indoor sensor must not be duplicated among the sensors. Please refer

to “INSTALL WIRELESS INDOOR SENSOR” for details

- This console can support dierent type of additional wireless sensor, e.g. soil moisture and

pool sensor. If you would like to pair up additional sensors, please check with your retailer for

more detail.

POINTING THE WIRELESS 7-IN-1 SENSOR TO SOUTH

The outdoor 7-IN-1 sensor is calibrated to point to North for the maximum accuracy. However,

for the user's convenience (e.g. users in the Southern hemisphere), it is possible to use the

sensor with the wind vane pointing to South.

1. Install the 7-IN-1 wireless sensor with its wind meter end pointing to South. (Please refer to

INSTALLATION OF THE WIRELESS SENSOR section for mounting details)

2. Select "S' in hemisphere section of the setup UI setup page. (Please refer to SETUP THE

WEATHER SERVER CONNECTION section for setup details)

3. Press

Apply

icon to conrm and exit.

11

EN

NOTE:

Changing the hemisphere setting will automatically switch the direction of the moon phase on

the display.

CREATE WEATHER SERVER ACCOUNT & SETUP WI-FI CONNECTION

The console can upload weather data to WUnderground and / or Weathercloud through WI-FI

router, you can follow the step below to setup your device.

NOTE:

The Weather Underground and Weathercloud website are subjected to change without notice.

CREATE WEATHER UNDERGROUND ACCOUNT

1. In https://www.wunderground.com click the "Join" on the top right corner to open the

registration page. Follow the instructions to create your account.

NOTE:

Use the valid email address to register your account.

2. After you have created your account and completed the Email validation, please go back to

the WUndergound web page to login. Then, click “My Prole” button on the top to open the

drop-down menu and click "My Weather Station".

3. In "My Weather Station" page bottom, press the "Add New Device" button to add your

device.

4. Follow their instruction to enter your station information, in the Step "Tell Us More About

Your Device", (1) enter a Name for your weather station. (2) choose “Other” in “Device

Hardware” section and ll in other the other information (3) select "I Accept" to accept

Weather underground's privacy terms, (4) click “Next” to create your station ID and key.

12

(2)

(3)

(4)

(1)

5. Jot down Your "Station ID" and "Station key" for the further setup step.

CREATE WEATHERCLOUD ACCOUNT

1. In https://weathercloud.net enter your information in "Join us today" section, then follow

the instructions to create your account.

NOTE:

Use the valid email address to register your account.

13

EN

2. Sign in weathercloud and then you will go the "Devices" page, click "+ New" to create new

device.

3. Enter all the information in Create new device page, for the Model* selection box select

the "W100 Series" under "CCL" section. for the Link type* selection box select the "Pro

Weather Link", Once you have completed, click Create.

4. Jot down your ID and key for the further setup step.

14

SETUP WI-FI CONNECTION

1. When you power up the console for the rst time, the console LCD will show ashing "AP"

and "

" icon to signify that it has entered AP (Access Point) mode, and is ready for WI-FI

settings. User can also press and hold the [ SENSOR / WI-FI ] key for 6 seconds to enter

AP mode manually.

2. Use the smart phone, tablet, or computer to connect the console through WI-FI.

3. In PC choose WiFi network settings or In Android / iOS choose setting

WI-FI to select the

console’s SSID: PWS-XXXXXX in the list and it will need several second to connect.

PWS-XXXXXX

PC (Windows 10) WI-FI network interface Android WI-FI network interface

4. Once connected, enter the following IP address into your internet browser’s address bar, to

access the console’s web interface:

http://192.168.1.1

NOTE:

- Some browsers will treat 192.168.1.1 as a search, so make sure you include http:// header.

- Recommended browsers, such as the latest version of Chrome, Safari, Edge, Firefox or

Opera.

- WI-FI network interface of PC or mobile subject to change.

WI-FI CONNECTION STATUS

Below is the WI-FI icon status on the console LCD:

Stable: Console is in

connection with WI-FI router

Flashing: Console is trying to

connect to WI-FI router

Flashing: Console currently in

Access Point (AP) mode

15

EN

SETUP THE WEATHER SERVER CONNECTION

Enter the following information into the below web interface "SETUP" page to connect the

console to weather server, If you do not want to use Wunderground.com or Weathercloud.net,

please empty the station ID & key to ignore the data upload.

nist.time.gov

Server URL:

0.0000 North

*Latitude:

0.0000

Enter 0 to 90, no negative numbers

Enter 0 to 180, no negative numbers

East

*Longitude:

Time server setup

Location for sunrise / sunset

WiFi Router setup

ADVANCED

Wunderground

Station ID:

WDw124

******

IPACIR23Wc

Weather server setup

Station key:

Router:

Add Router

Search

Security type:

Router Password:

WAP2

ROUTER_A

Language: English

Weathercloud

Station ID:

Station key:

******

IDCR21w1

http://WAC.com

Station ID:

URL:

Station key:

Mac address 00:0E:C6:00:07:10

Hemisphere

* Depends on the model

SETUP

Apply

Firmware version: 1.00

0:00

Time Zone:

N

Press "ADVANCED" icon

to Advanced page

Press to search router

Press to allow add

router manually

Enter the Latitude value

Enter the Longitude

value

SETUP page

Select setup UI display language

Press to complete the setting

Select router (SSID) for connection

Enter new Station ID and Station key

that assigned by Wunderground

Enter new Station ID and Station key

that assigned by weathercloud

Enter new Station ID and Station key

that assigned by the corresponding

weather server

Manually enter the SSID if not on list

Select time server

Select the direction (e.g. EU

countries Longitude is East and US

is West)

Select the sensor located hemisphere

(e.g. US and EU countries are also "N",

Australia is "S")

Reserved for validated weather server,

detail please consult with your retailer

Select router's security type (usually

WAP2)

Router's password (leave blank if the

Security type is "Open")

Select time zone of your location

NOTE:

- When WI-FI setup is completed, your PC or mobile will resume your default WI-FI connection.

- During AP mode, you can press and hold the [ SENSOR / WI-FI ] key for 6 seconds to stop

AP mode and the console will restore your previous setting.

TIME ZONE

To automatically set the time display to your time-zone, change the time zone in SETUP page

of previous section from '0:00' (default) to your time zone (e.g.+1:00 for Germany).

16

TIME SERVER CONNECTION STATUS

After the console has connected to the internet, it will

attempt to connect to the internet time server to obtain

the UTC time. Once the connection succeeds and the

console's time has been updated, the “

” icon will

appear on the LCD.

ADVANCE SETTING IN WEB INTERFACE

Press "ADVANCED" key at the top of web interface to enter the advance setting page, this page

allow you to set and view the calibration data of the console, as well as update the rmware

version on PC web browser.

Upload

Browse

Firmware version: 1.00

-560~ 560hpa / -16.54 ~ 16.54inHg / -420 ~ 420mmHg

Setting Range:

Temperature

o

C

Outdoor

Indoor

CH 1

CH 2

CH 3

CH 4

CH 5

CH 6

CH 7

Humidity %

Relative Pressure Offset:

Absolute Pressure Offset:

hpa

Range: -20 ~ 20

(Default: 0.0)

Current offset: 10Current offset: -9

Current offset: -5Current offset: 2

Current offset: -2Current offset: 3

Current offset: -2Current offset: 1.2

Current offset: -5Current offset: -0.2

Current offset: -3Current offset: -20.1

Current offset: -10Current offset: 11.5

Current offset: -3

(Default: 0)

Current offset: 10

(Default: 0)

Current offset: 0.2

Current offset: -5Current offset: 1

Pressure

Range: -20.0 ~ 20.0

o

C

-36.0 ~ 36.0

o

F (Default: 0.0)

*UV gain:

Range: 0.01 ~ 10(Default: 1.00)

Current gain: 1.1

*Light gain:

Range: 0.01 ~ 10(Default: 1.00)

Current gain: 1.1

* Depends on the model

*Wind speed gain:

*Wind direction:

*Rain gain:

Range: 0.5 ~ 1.5(Default: 1.00)

Range: -10 ~ 10(Default: 0

o

)

Range: 0.5 ~ 1.5(Default: 1.00)

Current gain: 0.85

Current offset: 2

o

Current gain: 0.75

SETUP ADVANCED

Select setting unit

Press "SETUP" icon to

Setup page

Outdoor and Ch 1~7

temperature calibration

section

Pressure calibration

section

Current rmware

version

The rmware update

function only available

in PC web browser

ADVANCED page

Select setting unit

The rain, wind speed, UV and Light

calibration use gain method. The

wind direction is +/- 10 oset.

Outdoor and Ch 1~7 humidity

calibration section

Current oset value is the value

that you set before to oset the

pressure reading.

CALIBRATION

1. User can input the oset and/or gain values for dierent parameters while current oset and

gain values are shown next to their corresponding blank.

2. Once completed, press

Apply

at the bottom of the SETUP page

The current oset value will show the previous value that you entered, please input the new value

in the blank if any changes needed, the new value will eective once you press

Apply

icon in

SETUP page.

17

EN

NOTE:

- Calibration of most parameter is not required, with the exception of Relative Pressure, which

must be calibrated to sea-level to account for altitude eects.

- Indoor temperature and humidity calibration values are not applicable for this console.

VIEW YOUR WEATHER DATA IN WUNDERGROUND

To view your weather station live data in a web browser (PC or mobile version), please visit

http://www.wunderground.com, and then enter your “Station ID” in the searching box. Your

weather data will show up on the next page. You can also login your account to view and

download the recorded data of your weather station.

Another way to view your station is use the web browser URL bar, type below in the URL bar:

https://www.wunderground.com/dashboard/pws/XXXX

Then replace the XXXX by your Weather underground station ID to view your station live data.

You can also use the Apple ipad's "WunderStation" app to

login your own weather station to view the live data.

WunderStation

VIEW YOUR WEATHER DATA IN WEATHERCLOUD

1. To view your weather station live data in a web browser (PC or mobile version), please visit

https://weathercloud.net and sign in your own account.

2. Click the

icon inside the pull down menu of your station.

3. Click "Current", "Wind", "Evolution" or "Inside" icon to view the live data of your weather

station.

FIRMWARE UPDATE

The console supports OTA rmware update capability. Its rmware may be updated over the

air anytime (whenever necessary) through any web-browser on a PC with WI-FI connectivity.

Update function, however, is not available through mobile/smart devices.

Upload

Browse

Firmware version: 1.00

Current rmware

version

Bottom of web interface ADVANCED page

Press to start upload the rmware

to console

Please to select the rmware le for

update

18

FIRMWARE UPDATE STEP

1. Download the latest version rmware to your PC.

2. Set the Console into AP (access point) mode then connect the PC to the console (ref to

"SETUP WI-FI CONNECTION" section in previous page).

3. Click the

Browse

in rmware update section and browse the location of the le you

download in step 1. To update the WI-FI rmware, click the

Browse

in WI-FI rmware

section.

4. Click the corresponding

Upload

to start transfer the rmware le to console.

5. In the meantime, the console will execute the update

automatically and will show the update progress on display (i.e.

100 is completion).

The update time is around 5 ~ 8 minutes

6. The console will restart once the update is completed.

7. The console will stay in AP mode for you to check the rmware version and all the current

setting.

IMPORTANT NOTE:

- Please keep connecting the power during the rmware update process.

- Please make sure your PC's WI-FI connection is stable.

- When the update process start, do not operate the PC and console until the update nished.

- During rmware update the console will stop upload data to the cloud server. It will reconnect

to your WI-FI router and upload the data again once the rmware update succeed. If the

console cannot connect to your router, please enter the SETUP page to setup again.

- After the rmware updates, user might need to input the Weather Underground ID and

password again.

- Firmware update process have potectial risk, which cannot guarantee 100% success. If the

update fail, please redo the above step to update again.

OTHER SETTING & FUNCTIONS OF THE CONSOLE

MANUAL CLOCK SETTING

This console is designed to obtain the local time by synchronize with the assigned internet time

server. If you want to use it oine, you can set the time and date manually. During the rst time

startup, press and hold the [ SENSOR / WI-FI ] key for 6 seconds and let the console back to

normal mode.

1. In normal mode, press and hold [ CLOCK SET ] key for 2 seconds to enter setting.

2. The setting sequence: DST AUTO/OFF

Hour Minute second 12/24 hour

format

Year Month Day M-D/D-M format Time sync ON/OFF weekday

Language.

3. Press [

] or [ ] key to change the value. Press and hold the key for quick-adjust.

4. Press [ CLOCK SET ] key to save and exit the setting mode, or the unit will automatically

exit the setting mode 60 seconds later without pressing any key.

NOTE:

- In normal mode, press [ CLOCK SET ] key to switch between year and date display.

- During the setting, you can press and hold [ CLOCK SET ] key for 2 seconds to back to

normal model.

DAYLIGHT SAVING TIME (DST)

DST function is set to "AUTO" by default (for EU or US version). If the current date on display is

with in the summer daylight saving period, the time will will be automically adjusted forward by

+1 hour, and DST icon will be shown on the LCD dsiplay.

19

EN

MOON PHASE

The moon phase is determined by the

time, date and time zone. The following

table explains the moon phase icons of

the Northern and Southern Hemispheres.

Please refer to

POINTING THE

WIRELESS 7-IN-1 SENSOR TO SOUTH

section about how to setup for the

Southern Hemispheres.

Northern

Hemisphere

Moon Phase

Southern

Hemisphere

New Moon

Waxing Crescent

First quarter

Waxing Gibbous

Full Moon

Waning Gibbous

Third quarter

Waning

Crescent

SUNRISE & SUNSET TIME

The console indicates your location’s sunrise & sunset time

by the time zone, latitude and longitude you entered. Please

enter the correct information in the regarding settings. If the

latitude and longitude values do not match the time zone,

the sunrise & sunset time cannot be shown.

SETTING ALARM TIME

1. In normal time mode, press and hold [ ALARM ] key for 2 seconds until the alarm hour digit

ashes to enter alarm time setting mode.

2. Press [

] or [ ] key to change the value. Press and hold the key for quick-adjust.

3. Press [ ALARM ] key again to step the setting value to Minute with the Minute digit ashing.

4. Press [

] or [ ] key to adjust the value of the ashing digit.

5. Press [ ALARM ] key to save and exit the setting.

NOTE:

- In alarm mode, the “

” icon will display on the LCD.

- The alarm function will turn on automatically once you set the alarm time.

ACTIVATING ALARM AND TEMPERATURE PRE-ALARM FUNCTION

1. In normal mode, press [ ALARM ] key to show the alarm time for 5 seconds.

2. When the alarm time displays, press [ ALARM ] key again to activate the alarm function.

Or press [ ALARM ] key twice to activate the alarm with ice pre-alarm function.

Alarm o Alarm on Alarm with ice-alert

NOTE:

Once the ice pre-alert activates, the pre-set alarm will sound and ice-alert icon will ash 30

minutes earlier if the outdoor temperature is below -3°C.

20

When clock reach the alarm time, alarm sound will start.

Where it can be stopped by following operation:

- Auto-stop after 2 minutes alarming if without any operation and the alarm will activate again in

the next day.

- By pressing [ALARM / SNOOZE] key to enter snooze that the alarm will sound again after 5

minutes.

- By pressing and hold [ALARM / SNOOZE] key for 2 seconds to stop the alarm and will

activate again in the next day

- By pressing [ ALARM ] key to stop the alarm and the alarm will activate again in the next day.

NOTE:

- The snooze could be used continuously in 24 hours.

- During the snooze, the alarm icon “

” will keep ashing.

TEMPERATURE / HUMIDITY FUNCTION

- The temperature and humidity reading are display on the outdoor and indoor (CH) section.

- Use the [ °C / °F ] slide switch to select the temperature display unit.

- If temperature / humidity is below the measurement range, the reading will show “Lo”. If

temperature / humidity is above the measurement range, the reading will show “HI”.

COMFORT INDICATION

The comfort indication is a pictorial indication

based on indoor air temperature and humidity in

an attempt to determine comfort level.

Too cold Comfortable Too hot

NOTE:

- Comfort indication can vary under the same temperature, depending on the humidity.

- There is no comfort indication when temperature is below 0°C (32°F) or over 60°C (140°F).

WIRELESS SENSOR SIGNAL RECEIVING

1. The console display signal strength for the wireless sensor(s), as per table below:

Outdoor 7-in-1 sensor

Indoor channel sensor

No signal Weak signal Good signal

2. If the signal has discontinued and does not recover within 15 minutes, the signal icon will

disappear. The temperature and humidity will display “Er” for the corresponding channel.

3. If the signal does not recover within 48 hours, the “Er” display will become permanent. You

need to replace the batteries and then press [ SENSOR / WI-FI] key to pair up the sensor

again.

VIEW THE OTHER INDOOR CHANNELS (OPTIONAL FEATURE WITH ADD ON EXTRA

SENSORS)

This console is capable to pair with a wireless 7-IN-1 sensor and up to 7 wireless indoor

sensors. If you have 2 or more Indoor sensors, you can press [ CHANNEL ] key to switch

between dierent wireless channels in normal mode, or press and hold [ CHANNEL ] key for 2

seconds to toggle auto-cycle mode to display the connected channels at 4 seconds interval.

During auto-cycle mode, the

icon will show on the indoor channel section of the console's

display. Press [ CHANNEL ] key to stop auto cycle and display the current channel.

La pagina sta caricando ...

Explore Scientific Professional WIFI Weather Centre 7in1 Manuale del proprietario

Explore Scientific Professional WIFI Weather Centre 7in1 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti