Candy CDS120W-02S Manuale utente

Marca: Candy

Modello: CDS120W-02S

Categoria: Lavastoviglie

Tipo: Manuale utente

Questo manuale è adatto anche per

User instructions

CDS 120

DISHWASHER

Congratulations!

Thank you for choosing a Candy

appliance; quality dishwashers which

guarantee high performance and

reliability.

Candy manufacture a vast range

of domestic appliances: washing

machines, washer/dryers, cookers,

microwave ovens, ovens and hobs,

refrigerators and freezers.

Ask your dealer for the catalogue with

the complete range of Candy products.

Please read this booklet carefully as

it provides important information

regarding the safe installation, use,

and maintenance of the machine,

together with some useful advice on

how to achieve the best results from

your dishwasher.

For future reference please keep this

instruction booklet in a safe place.

CUSTOMER SERVICE AND

GUARANTEE

Your new appliance is fully guaranteed

by the manufacturer for 12 months

against electrical/mechanical break-

down excluding:

A. Any faults which occur due to bad

installation or misuse of the machine.

B. Any faults which occur due to repair

of, or interference with, the machine

by any person not authorised by the

manufacturer to carry out service.

C. Any faults which occur due to

any parts which are fitted to the

machine which are not the original

manufacturers parts.

D. Any faults arising from non-domestic

use or unusual or abnormal use of

the machine.

E. Any faults arising from operation at

incorrect voltage.

F. Any faults arising from incorrect

operation of the machine.

The guarantee applies to Gt Britain

and Northern Ireland only, and is an

addition to your statutory rights.

AFTER SALES SERVICE

For service and repairs call your local engineer on our national telephone number:

GIAS Service Tel: 08705 400 600

Support Service (Eire 018301 666)

SAFETY INSTRUCTIONS

There are certain basic safety rules

which are valid for any domestic

appliance.

Installation

■ Make sure that the plug fitted to the

machine is compatible with the power

supply socket. If it is not, get a suitably

qualified person to fit the correct type,

and to make sure that the cables to the

mains socket are able to cope with the

power rating of the appliance.

■ Ensure that the dishwasher does not

crush power cables.

■ In general it is not advisable to use

adaptors, multiple plugs and/or extension

cables.

■ Should it be necessary to replace the

supply cord, call the After Sales Service

Centre.

Safety

■ Never touch the appliance when your

hands or feet are wet or damp.

■ Do not use when your feet are bare.

■ Do not remove the plug from the mains

supply socket by pulling the mains cable

or the machine itself.

■ Do not leave the appliance exposed to

the elements (rain, sun etc).

■ Do not let children (or others incapable

of operating it) use the machine without

supervision.

■ Water left in the machine or on the

dishes at the end of the wash programme

should not be swallowed.

■ The door should not be left in the open

position since this could present a potential

hazard ( es. tripping ).

■ Leaning or sitting on the open door of

the dishwasher could cause it to tip over.

WARNING !

Knives and other utensils with sharp

points must be loaded in the basket

with their points down or placed in a

horizontal position.

Daily use

■ This appliance is be designed for domestic

use only.

■ The dishwasher is designed for normal

kitchen utensils.

Objects that have been contamined by

petrol, paint, traces of steel or iron,

corrosive chemicals, acids or alkalis

must not be washed in the dishwasher.

■ If there is a water softening device installed

in the home there is no need to add

salt to the water softener fitted in the

dishwasher.

■ Cutlery is washed best if it is placed in

the basket with the handles downwards.

■ If the appliance breaks down or stops

working properly, switch it off, turn off the

water supply and do not tamper with it.

Repair work should only be carried out

by an approved service agent and only

genuine spare parts should be fitted. Any

failure to follow the above advice may

have serious consequences for the safety

of the appliance.

Disposal

■ The dishwasher has been made from

materials which can be recycled so that it

can be disposed of in an environmentally

friendly way.

■ If you wish to dispose of an old dishwasher

be careful to remove the door to

eliminate the risk of children becoming

trapped inside it.

CONTENTS

Safety advice

Setting up, installation

Water softener unit

Adjusting the upper basket

Loading the dishes

Information for test laboratories

Half load washing

Loading the detergent and rinse aid

Cleaning the filters

Some practical hints

Routine cleaning and maintenance

Description of the controls

Technical data

Operating the programmes and special functions

Programme selection

Identifying minor faults

pag. 5

pag. 6

pag. 9

pag. 11

pag. 12

pag. 14

pag. 15

pag. 16

pag. 18

pag. 19

pag. 20

pag. 21

pag. 22

pag. 24

pag. 26

Please read the instructions in this booklet carefully because they contain important

information on how to install, use and maintain your dishwasher safely as well as

containing useful tips on how to make the most of it.

Keep this booklet safe for future reference.

Fig. A

Water connection

IMPORTANT

The appliance must be connected to

the water mains using new hose-sets.

The old hose-sets should not be reused.

■ The inlet and drain hoses can be directed

to left or right.

IMPORTANT

The dishwasher can be connected to

either cold or hot water, as long as it

is no hotter than 60 °C.

■ Water pressure must be between

0,08 MPa and 0,8 MPa. If the pressure is

below the minimum consult our service

department for advice.

■ The inlet hose must be connected to a

tap so that the water supply can be cut

off when the machine is not in use

(fig. 1 B).

■ The dishwasher is fitted with 3/4" threaded

connector (fig. 2).

■ Connect inlet hose “A” to water tap “B”

with a 3/4" attachment making sure that

it has been properly tightened.

■ If it is necessary, the inlet pipe can be

lengthened up to 2,5 m. The extension

pipe is available from the After Sales

Service Centre.

■ If limescale deposits or sand are present

in the water, it is advisable to obtain the

appropriate filter, art. 9226085, from the

After Sales Service Centre (fig. 3). The

filter “D” must be inserted between the tap

“B” and the inlet hose “A”, remembering

to fit the washer “C”.

■ If the dishwasher is connected to new

pipes or to pipes which have not been in

use for a long time run water through for

a few minutes before connecting the

inlet hose. In this way no deposits of

sand or rust will clog up the water inflow

filter.

INSTALLATION

(Technical notes)

IMPORTANT

When the appliance is located on a

carpet floor, attention must be paid to

ensure that there is no obstruction to

the bottom vents.

Make sure that the plug on the

appliance remains accessible after

installation.

Electrical connection

Plug your dishwasher into the power

socket.

If the plug we supply does not fit :

■ CUT IT OFF AND DESTROY IT!

You can't use it on other appliances, and

the exposed wires could be dangerous if

anyone plugged it in.

■ Fit a suitable plug, as follows:

WARNING!

THIS APPLIANCE MUST BE EARTHED.

Fuses and plugs

This appliance should be used only on a

socket with a minimum rating of 13 Amp.

Our ready-fitted plug is already equipped

with a 13 amp fuse which is BS 1362 ASTA

approved.

Any replacement should be exactly the same.

If the fuse cover is lost, do not use the plug

until it is replaced.

A correct replacement fuse cover (obtaina-

ble from your dealer or Electricity board)

must be the same colour as shown or

named on the insert on the base of the

plug.

Manufacturer declines all responsibility

for any damage due to non-earthing of

the machine.

This appliance complies with

Directives 89/336/EEC, 73/23/EEC

and following changes.

Green and

yellow wire

Marked with the letter E,

OR marked with the Earth

symbol,

OR coloured green,

OR coloured green and

yellow.

Blue wire

Brown wire

Marked N,

OR coloured black.

Marked L,

OR coloured red.

Connect to the terminal in the plug

If your water is at level 0, you need not use

any regenerating salt, nor need you make

any adjustment, as your water is soft.

According to the degree of hardness of

your water, regulate the softener unit in the

following way:

1. remove the lower rack. Unscrew and

remove the cap from the salt dispenser

located in the bottom of the tub

(fig. A"1");

2. turn the selector screw to the required

position with a screwdriver or a knife.

TYPE 1

TYPE 2

WATER SOFTENER UNIT

Depending on the source of the supply,

water contains varying amounts of limestone

and minerals which are deposited on the

dishes leaving whitish stains and marks.

The higher the level of these minerals

present in the water, the harder the water is.

The dishwasher is fitted with a water

softener unit which, through the use of

special regenerating salt, supplies

softened water for washing the dishes.

The softener unit can treat water with a

hardness of up to 60°fH (French grading)

or 33°dH (German grading) through five

different settings.

The degree of hardness of your water can

be obtained from your water supply

company.

Regulating the water softener

The table below lists different degrees of

water hardness with the corresponding set-

ting for the softener unit.

*The water softener unit is set in the

factory at level 2, as this is suitable for the

majority of users.

Level

Water

hardness

°fH

(French)

0-9

10-30

31-40

41-50

51-60

Water

hardness

°dH

(German)

0-5

6-16

17-22

23-27

28-33

Use of

regenerating

salt

YES

Water

softener

setting

FREE

position N.1

position N.2

position N.3

position N.4

N°

washes

Connecting the outlet hose

■ The outlet hose should disharge into a

standpipe, making sure that there are no

kinks (fig. 4).

■ The standpipe must be at least 40 cm

above floor level and it must have an

internal diameter of at least 4 cm.

■ It is advisable to fit an anti-odour air trap

(fig. 4X).

■ If necessary the outlet hose can be

extended up to 2,5 m, provided that it is

kept at a maximum height of 85 cm

above floor level. The extension pipe is

available from the After Sales Service

Centre.

■ The hose can be hooked over the side of

the sink, but it must not be immersed in

water, in order to prevent water from

being syphoned back to the machine

when this is in operation (fig. 4Y).

■ When installing the appliance under a

worktop the hose pipe clamp must be

attached to the wall in the highest possible

position under the worktop (fig. 4Z).

■ Check that there are no kinks in the inlet

and outlet hoses.

Opening the door

Put your hand into the recess and pull.

If the machine comes open while it is working,

an electrical safety device automatically

switches everything off.

IMPORTANT

For the machine to work properly,

the door should not be opened while

it is in operation.

Closing the door

Place the baskets in the machine.

Make sure that both the spray arms are

free to rotate and are not obstructed by

cutlery, crockery or pans. Close the door,

pressing on it to make sure it is firmly shut.

Adjustment of the upper

basket

If 27 cm to 31 cm plates are normally used,

load them onto the lower basket after the

upper basket has been placed in its upper

position and proceed as detailed below:

1. Turn the front stops “A” outwards;

2. Take out the basket and remount it in the

upper position;

3. Replace the blocks “A” in their original

position.

Dishes that are bigger than 20 cm in

diameter can no longer be loaded onto the

upper basket and the mobile supports

cannot be used when the basket is in the

upper position.

Loading the salt

■ On the bottom of the machine there is a

container for the salt for regenerating

the softener.

■ It is important to use only a salt that is

specifically designed for dishwasher.

Other types of salt contain small quantities

of insoluble particles which over a long

period of time may affect and deteriorate

the softener performance.

■ To add salt, unscrew the cap of the con-

tainer on the bottom and then refill the

container.

■ During this operation a little water will

overflow; but keep adding salt until the

container is full. When the container is

full, clean the thread of salt residue and

retighten the tap.

■ After loading the salt, it is recommended

running a complete washing cycle,

or COLD RINSE programme. The salt

dispenser has a capacity of between 1.5

and 1.8 kg and, for efficient use of the

appliance, it should be refilled from time

to time according to the regulation of the

water softener unit.

IMPORTANT

(Only for first start up)

When the appliance is used for the

first time, after completely filling the

salt container, it is necessary to add

water until the container overflows.

Salt loading indicator

This model is provided with an indicator light

on the control panel which will light up

when it is necessary to reload the salt

container.

IMPORTANT

The appearance of white stains on

dishes is generally an important

sign that the salt container needs

filling.

Astandard daily load is represented in figs. 1, 2 and 3.

Upper basket (fig. 1)

A = soup plates

B = dinner plates

C = dessert plates

D = saucers

E =cups

F = glasses

Upper basket (fig. 2)

A = soup plates

B = dinner plates

C = dessert plates

D = saucers

E =cups

F = glasses with stems

G = glasses

H = single section cutlery basket

Lower basket (fig. 3)

A = medium-sized saucepan

B = large saucepan

C = frying pan

D = lids

E =tureens, serving dishes

F = cutlery

G = oven dishes

Please load the dishwasher sensibly to ensure the

best wash results.

Cutlery basket (fig. 4)

The cutlery basket is made with two detachable

parts which will enable various loading options. The

two parts can be detached by sliding the left section

away from the right section.

FAG

LOADING DISHES

Using the upper basket

■ The upper basket is provided with mobi-

le racks hooked to the sides of the

basket which can be regulated in two

positions: upright and lowered. In the

lowered position the racks may be used

for tea and coffee cups, kitchen knives

and ladles. Glasses with stems may be

safely hung on the ends of the racks.

Glasses, cups, saucers and dessert

plates may be loaded under the racks.

■Soup plates and ordinary plates may be

loaded with the rack in the upright

position. Plates should be loaded

vertically with the underside of the plate

towards the back of the dishwasher with

a space between each plate to allow

water to pass freely.

■ It is advisable to load plates of the same

size together in order to utilize maximum

basket capacity.

■ Plates may be loaded in a single row

(fig. 1) or on both rows (fig. 2).

■ It is advisable to load large plates

(approx. 27 or more cm) slightly tilted

towards the rear to facilitate introduction

of the basket into the machine.

■ Salad bowls and plastic bowls may also

be loaded on the upper basket. It is

advisable to block these in place so that

the jets of water do not make them

overturn.

■ The upper basket has been designed to

offer maximum flexibility in use and can

be loaded with up to 24 plates on two

rows, up to 30 glasses on five rows or a

mixed load.

Using the lower basket

■ Saucepans, oven dishes, tureens, salad

bowls, lids, serving dishes, dinner

plates, soup plates and ladles can be

loaded on the lower basket.

■ Place the cutlery in the plastic cutlery

holder with the handles pointing

upwards.

■ Place the cutlery holder on the lower

basket (fig. 3), making sure that the

cutlery does not get in the way of the

rotating arms.

IMPORTANT

The lower basket has a safety-stop

device, for its safe extraction, also

especially useful with a full load.

For loading salt, cleaning filter and for

ordinary maintenance, the complete

extraction of the basket is necessary.

Half load wash upper basket

1/2 mixed load (fig. 1)

A = glasses

B = cups

C = soup plates

D = dessert plates

E = saucers

F = saucepan

G = Irying pan

H =medium bowl

I = small bowl

1/2 load standard (fig. 2)

A = 6 glasses

B = 6 cups

C = serving dish

D = 6 soup plates

E =6 dinner plates

F =6 dessert plates

G =6 saucers

H =medium bowl

I = small bowl

Place the cutlery in the plastic cutlery holder on the lower basket.

Lower basket (fig. 6)

M = 8 + 4 soup plates

N = 11 + 1 dinner plates

O = 12 dessert plates

P = serving dish

Q = cutlery

Upper basket (fig. 5)

A = 5 + 5 + 2 glasses

B = 12 saucers

C = 4 + 4 + 4 cups

D = small bowl

E = medium bowl

F = large bowl

G = 1 + 1 forks

H = 1 + 1 serving spoons

I = 3 + 3 + 3 + 3 dessert spoons

L = 3 + 3 + 3 + 3 teaspoons

INFORMATION FOR THE TEST LABORATORIES

General programme comparison (Ref. EN 50242 Standards)

(see programmes selection)

1. Upper basket position: low

2. Normal load

3. Shine setting: 6

12 international place load (Ref. EN 50242)

Correct loading is indicated, in fig. 5 for the upper basket, in fig. 6 for the lower

basket and in fig. 7 for the cutlery basket.

Cutlery basket (fig. 7)

Place the side racks in the lower position

and fill with 6 + 6 knives(R); in the spaces

left insert cutlery with the handles down.

Take care not to load more than two different

types of cutlery in the same compartment.

4. Amount of detergent:

- 8 g for pre-wash;

- 22 g for wash.

FULL EMPTY

dark light

Filling the rinse aid container

The rinse aid, which is automatically

released during the last rinsing cycle, helps

the dishes to dry quickly and prevents

spots and stains forming.

The rinse aid container can be found to the

left of the detergent container (fig. A "3").

To open the lid, push the reference mark

and, in the same time, pull the tab of

opening.

It is always advisable to use rinse aid that

is specifically designed for dishwasher.

Check the rinse aid level through the

indicator eye (C) which is located on the

dispenser.

Regulating the rinse aid from 1 to 6

The regulator (D) is placed under the lid

and can be turned using a coin.

The recommended position is 4.

The limestone content of the water

considerably affects the formation of

limescale and the drying performance.

It is therefore important to regulate the

quantity of rinse aid to achieve good

washing results.

If, after the wash, streaks occur on the

dishes, decrease the amount by one

position. If whitish spots occur, increase the

amount by one position.

■ the effectiveness of detergents containing

the built in water softener/salt depends

on the hardness of your water supply.

Check that the hardness of your water

supply is within the effective range given

on the detergent packaging.

In certain circumstances use of combined

detergents can cause:

■ limescale deposits on dishes or in the

dishwasher;

■ a reduction in washing and drying

performance.

Should this occur, we would recommend

using traditional separate products – salt,

detergent and rinse agent. This will ensure

that the water softener in the dishwasher

operates correctly.

Please note that on return to the use of

conventional salt, a number of cycles will

be required before the system becomes

fully efficient again.

IMPORTANT

Any problems which arise as a direct

result of the use of these products

are not covered by our warranty.

LOADING THE DETERGENT

AND THE RINSE AID

Filling the detergent container

IMPORTANT

It is essential to use a detergent

that is specifically designed for

dishwashers either in powder, liquid

or tablet form.

“FINISH” gives very good results and can

be easily obtained.

Unsuitable detergents (like those for

washing up by hand) do not contain the

proper ingredients for use in a dishwasher,

and stop the dishwasher from working

correctly.

Normal wash

The detergent container is inside the door

(fig. A “2”). If the lid of the container is

closed, press the button (A) to open.

At the end of every wash cycle the lid is

always open and ready for the next time

the dishwasher is used.

The amount of detergent to be used varies

according to how dirty the dishes are and

on the type of dishes to be washed.

We advise using 20:30 g of detergent in the

wash section of detergent compartment (B).

After pouring the detergent into the container,

close the lid, firstly pushing (1) and then

pressing on it (2) until you hear the click.

Since not all detergents are the same the

instructions on the boxes of detergent can

vary. We should just like to remind users

that too little detergent does not clean the

dishes properly whilst too much detergent

will not produce better results and is also a

waste.

IMPORTANT

Do not use an excessive amount of

detergent and help limit damage to

the environment at the same time.

CAUTION!

IMPORTANT NOTE ON THE USE OF

COMBINED DETERGENTS.

If you are planning to use combined detergents

i.e. those with built in salt and/or rinse

agent, we would advise the following:

■ read carefully and follow the manufacturer’s

instructions given on the packaging;

■ some combined detergents, particularly

those with built in rinse agent, provide

best results when used with specific

programmes;

PRATICAL HINTS

How to get really good wash

results

■ Before placing the dishes in the

dishwasher, remove any remaining

food (bones, shells, pieces of meat or

vegetables, coffee grounds, skin of fruit,

cigarette ash, tooth picks etc. to avoid

blocking the filters, water outlet and

washing arm nozzles.

■ Try not to rinse the dishes before

loading them into the dishwasher.

■ If saucepans and oven dishes are

encrusted with the remains of burnt or

roast food, it is advisable to leave them

to soak before washing.

■ Place the dishes face downwards.

■ Try to place the dishes in such a way

that they are not touching one another.

If they are loaded properly you will get

better results.

■ After loading the dishes check that the

washing arms can rotate freely.

■ Pans and other dishes that have

particularly stubborn food particles or

remnants of burnt food should be left to

soak in water with dishwasher

detergent.

■ To wash silver properly:

a) rinse the silver immediately after

use, especially if it has been used for

mayonnaise, eggs, fish etc.;

b) do not sprinkle detergent onto it;

c) keep it separate from other metals.

How to make savings

■ If you want the dishwasher to give a

complete wash, place the dishes in the

dishwasher at the end of each meal and

if necessary turn on the COLD RINSE

cycle to soften the food remains and

remove bigger particles of food from the

new load of dishes.

When the dishwasher is full start the

complete wash cycle programme.

■ If the dishes are not very dirty or if the

baskets are not very full select an

ECONOMY programme, following the

instructions in the program list.

What not to wash

■ It should be remembered that not all

dishes are suitable for washing in a

dishwasher.We advise against using

the dishwasher to wash items in

thermoplastic, cutlery with wooden or

plastic handles, saucepans with

wooden handles, items in aluminium,

crystal, leaded glass unless otherwise

stated.

■ Certain decorations may fade. It is

therefore a good idea before loading the

whole batch to wash just one of the

items first so as to be sure that others

like it will not fade.

■ It is a good idea not to put silver cutlery

with non-stainless steel handles into

the dishwasher as there could be a

chemical reaction between them.

IMPORTANT

When buying new crockery or

cutlery always make sure that they are

suitable for washing in a dishwasher.

Useful hints

■ In order to avoid any dripping from the

top rack, remove the lower rack first.

■ If the dishes are to be left in the

machine for some time, leave the door

ajar, to let some air circulate and to

improve the drying performance.

CLEANING THE FILTERS

The filter system (fig.A “4”) consists of:

a central container that traps the larger

particles;

a flat gauze that continuously filters the

wash water;

a micro filter, located beneath the gauze,

that traps the tiniest particles ensuring a

perfect rinse.

■ To achieve excellent results every time,

the filters should be checked and

cleaned after each wash.

■ To remove the filter unit, simply turn the

handle anticlockwise (fig. 1).

■ For ease of cleaning, the central container

is removable (fig. 2).

■ Remove the gauze filter (fig.3) and

wash the whole unit under a jet of

water. If necessary a small brush can

be used.

■ With the Self-cleaning Micro filter,

maintenance is reduced and the filter

unit need only be checked every two

weeks. Nevertheless, after each wash it

is advisable to check that the central

container and the gauze filter are not

clogged.

WARNING!

After cleaning the filters, make sure

that they are correctly reassembled

and that the gauze filter is properly

positioned at the bottom of the

dishwasher.

Make sure that the filter is screwed

back, clockwise, into the gauze, as

poor seating of the filter unit could

have an adverse effect on the

efficiency of the appliance.

IMPORTANT

Never use the dishwasher without

the filters.

EN 50242 place load

Capacity with pans and dishes

Water supply pressure

Fuse

Power input

Supply voltage

8 persons

Min. 0,08 - Max 0,8 MPa

(see rating plate)

D Programme selector

E "SALT EMPTY" light

F Indicator light "WASHING"

DESCRIPTION OF THE CONTROL

TECHNICAL DATA:

DIMENSIONS:

A "HALF LOAD" button

B "ON/OFF" button

C Door handle

Height

Depth

Width

Depth with door open

82 ÷ 88,5

59,8

117

WHEN CYCLE IS FINISHED

After every wash it is essential to turn off

water supply and to switch off the machine

by pressing the On/Off button to the off

position.

If the machine is not going to be used for

some time, it is advisable to follow these

rules:

1. do an empty wash with detergent in order

to clean the machine of any deposits;

2. pull out the electric plug;

3. turn off the water tap;

4. fill the rinse aid container;

5. Ieave the door ajar;

6. keep the inside of the machine clean;

7. If the machine is left in places where the

temperature is below 0°C any water left

inside the pipes may freeze. Wait until

the temperature rises above zero and

then wait for about 24 hours before

starting up the dishwasher.

CLEANING AND

MAINTENANCE

■ To clean the dishwasher outside, do not

use solvents (degreasing action) neither

abrasives, but only a cloth soaked with

water.

■ The dishwasher does not require special

maintenance, because the tank is

self-cleaning.

■ Regularly wipe the door gasket with a

damp cloth to remove any food remains

or rinse aid.

■ It is advisable to remove limestone

deposits or dirt periodically, by doing an

empty wash; pour a glass of vinegar on

the bottom of the tank and select the

light wash.

■ If, in spite of the routine cleaning of the

filters, you notice that the dishes or pans

are not properly washed or rinsed, check

that all the spray heads on the rotor

arms (fig. A “5”) are clear.

If they are blocked, clean them in the

following way:

1. to remove the upper rotor arm, turn it

until it lines up with the stop marked

by the arrow (fig. 1). Push it upwards

(fig. 1b) and, keeping it pushed in,

unscrew it in a clockwise direction

(to reassemble it repeat the same

operation, but turn it anticlockwise).

The lower rotor arm can be removed

simply by pulling it upwards (fig. 2);

2. wash the rotor arms under a jet of water

to clear any blockage in the spray

heads;

3. when you have finished, refit the rotor

arms in the same position, remembering

to re-align the arrow and screw into

position.

■ Both the door lining and the tank lining

are in stainless steel; however, should

spots caused by oxidation occur, this is

probably due to a high level of iron salts

presents in the water.

■ The spots can be removed with a mild

abrasive agent; never use chlorine

based materials, steel wool, etc.

AB C D E F

SELECTING THE PROGRAMME

AND SPECIAL FUNCTIONS

(Use in conjunction with programme guide)

Setting a programme

WARNING!

Before to set any programme, the

programme selector must be in the

"RESET" position and the indicator

light "WASHING" ( ) must be out.

Make sure that the "ON/OFF" ( )

button is pressed.

To set the programme, press the "ON/OFF"

button: then turn the dial (in a clockwise or

anti-clockwise direction) until the pointer

( ) is in line with the symbol of the required

programme.

After about 4 seconds, the indicator light

"WASHING" will come on.

IMPORTANT

While a programme is running, the

programme selector will remain in

the selected position, and will NOT

MOVE.

Option buttons

"HALF LOAD" button

By using this option, it is possible to wash

a smaller quantity of crockery: you should

load only the upper basket for dishes and

place cutlery in the tray in the bottom

basket.

This reduces water and energy consump-

tion and requires a smaller quantity of

detergent.

Interrupting a programme

Opening the door is not recommended

while a programme is running, especially

during the main washing phase and final

drying.

However, the dishwasher will stop automatically

when the door is opened.

If the door is opened during a programme,

the indicator light "WASHING" will start

flashing, up to when you re-close the door.

At this point, the programme will restart

from where it had been interrupted (if it is

necessary, the appliance will make a short

thermal anti-shock programme before).

If you wish to change or cancel the

programme that is running, carry out

the following:

turn the programme selector to "RESET"

position. The dishwasher will automatically

empty the water and after a few seconds

the indicator light "WASHING" will go off.

A new wash setting can now be made.

WARNING!

Before starting a new programme,

you should check that there is still

detergent in the dispenser.

If necessary, top up the dispenser.

If there is any break in the power supply

while the dishwasher is operating, a

special memory stores the selected

programme and, when the power is

restored, it continues where it left off.

End of programme

At the end of the programme, the indicator

light "WASHING" will start flashing.

Turn the programme selector to "RESET"

position, wait until the indicator light

"WASHING" goes off and press the

"ON/OFF" button.

Setting of new programme

Whenever you want to set a new programme,

you MUST turn the programme selector

to "RESET" position and wait for the

"WASHING" indicator light to go off.

Troubleshooting

While you are setting a programme, the

indicator light "WASHING" will start

flashing very quickly if the electronics

detect some incorrect programming function.

In this case, turn the programme selector to

the "RESET" position and the indicator light

"WASHING" will then go off. After this you

should again set the required programme.

If the malfunction continues, contact the

After Sales Service Centre.

IMPORTANT

This dishwasher is equipped with an

anti-overflow safety device which will

automatically empty any excess

water should a problem occur.

WARNING!

To ensure the correct operation of

the anti-overflow safety device, it is

recommended not to move or to tilt

the dishwasher during operation.

If it is necessary to move or to tilt the

dishwasher, first make sure the

washing cycle is finished and that no

water is left in the tank.

Programme

PROGRAMME SELECTION

COLD RINSE

HYGIENIC 75°C

UNIVERSAL 65°C

A CLASS 1h 70°C

ECO 45°C

DELICATE 45°C

RAPID 32’ 50°C

Short cold pre-wash for items that are

stored in the dishwasher until you are

ready to wash a full load.

Once a day - for heavily soiled pans and

any other items that have been left all day

for washing.

Once a day - for normal soiled pans and

any other items that have been left all day

for washing.

Suitable for heavily soiled items that are to

be washed straight after a meal.

(Max 8 place load)

Energy Saving Programme suitable for

normal soiled items. Using detergents with

enzyme.

Programme standardised to EN 50242.

Suitable for delicate crockery and glassware.

Also for less soiled items excluding pans.

Quick wash for dishes which are to be

washed immediately after the meal. Wash

load of 4/6 persons.

•

••

70°C

Check list

Avarage

duration

minutes

Special function

buttons

available

Detergent for soaking

(Prewash)

Detergent for washing

Clean filter

Check rinse aid

dispenser

Check salt container

Hot pre-wash

Cold pre-wash

Main wash

First cold rinse

Second cold rinse

Hot rinse with rinse aid

With cold water (15°C)

(Tolerance ± 10%)

“HALF LOAD” button

•

••••

•••

45°C

50°C

••

65°C

••

YES

75°C

120

•• ••

••••

45°C

140

••

•

••

N/A

N/A = OPTION NOT AVAILABLE

••

Description

Wash with soaking cycle (Prewash)

If setting the HYGIENIC programme, a second dose of about 20 g of detergent (1table-spoon)

must be added directly in the dishwasher. For

A CLASS 1h programme add 5 g.

YES

Programme contents

•

••

N.B.: Should any of the situations occur and should the machine give a bad wash performance,

it is necessary to remove the deposits from the dishes by hand since the final drying cycle hardens the

deposits which a second wash in the machine would not be able to remove.

If the malfunction continues contact a Service Centre quoting the serial number of the dishwasher.

This is found on the plaque on the inside of the dishwasher door at the top or on the guarantee.

This information will make it possible to take more effective action more quickly.

The manufacturers decline any responsibility for any printing mistakes in this instruction booklet.

They also reserve the right to modify their own appliances as necessary without altering the

essential characteristics.

FAULT CAUSE REMEDY

7 - Load of dishes is only

partially washed

8 - Presence of white spots

on dishes

9 - Noise during wash

10 -The dishes are not

completely dry

See causes for no. 5

Bottom of saucepans have not

been washed well

Edge of saucepans have not

been washed well

Spray arms are partially blocked

The dishes have not been

properly loaded

The end of the outlet hose is in

the water

The incorrect amount of

detergent has been measured

out; the detergent is old and hard

The wash programme is not

thorough enough

The lower basket dishes have

not been washed

Water is too hard

The dishes knock against one

another

The revolving arms knock against

the dishes

Inadequate air flow

Check

Burnt on food remains must

be soaked before putting pans

in dishwasher

Reposition saucepans

Remove spray arms by

unscrewing ring nuts clockwise

and wash under running water

Do not place the dishes too

closely together

The end of the outlet hose

must not come into contact

with the outflow water

Increase the measure

according to how dirty the

dishes are and change detergent

Choose a more vigorous

programme

Depress half load button

Check salt and rinse aid level

and regulate amount.

Should the fault persist,

Contact Service Centre

Re-check loading of dishes in

the basket

Again re-check loading

Leave the dishwasher door ajar

at the end of the wash program

to allow the dishes to dry naturally

IDENTIFYING MINOR FAULTS

Should the dishwasher fail to operate, before contacting the Service Centre, make

the following checks:

FAULT CAUSE REMEDY

1 - Machine completely dead

2 - Machine does not

draw water

3 - Machine does not

discharge water

4 - Machine discharges

water continuously

5 - Spray arms are not heard

to rotate

6 - On electronic appliances

without a display: one or

more LED flashing quickly.

Plug is not connected to wall

socket

O/I button has not been pressed

Door is open

No electricity

See causes for no. 1

Water tap is turned off

Programme selector is not at

correct position

The inlet hose is bent

The inlet hose filter is not

correctly connected

Filter is dirty

Outlet hose is kinked

The outlet hose extension is

not correctly connected

The outlet connection on the

wall is pointing downwards not

upwards

Position of outlet hose is too

low

Excessive amount of detergent

Item prevents arms from rotating

Plate and cup filter very dirty

Water inlet tap turned off

Connect electric plug

Press button

Close door

Check the fuse in the plug and

the electricity supply

Check

Turn water tap on

Turn programme selector to

correct position

Eliminate the bends in the hose

Clean the filter at the end of the

hose

Clean filter

Straighten outlet hose

Follow the instructions for

connecting the outlet hose

carefully

Call a qualified technician

Lift outlet hose to at least 40 cm

above floor level

Reduce amount of detergent

Use suitable detergent

Check

Clean plate and cup filter

Switch off the appliance.

Turn on the tap.

Re-set the cycle.

The manufacturer declines all responsibility in the event of any printing mistakes in this

booklet. The manufacturer also reserves the right to make appropriate modifications to

its products without changing the essential characteristics.

04.09 - 41012992 - Printed in Italy - Imprimé en Italie

Candy CDS120W-02S Manuale utente

Marca: Candy

Modello: CDS120W-02S

Categoria: Lavastoviglie

Tipo: Manuale utente

Questo manuale è adatto anche per

Scarica il pdf

rapporto

Candy CDS120W-02S Manuale utente

Questo manuale è adatto anche per

Candy CDS120W-02S Manuale utente

Documenti correlati

Altri documenti