Spectrum Industries 37373 Manuale del proprietario

Marca: Spectrum Industries

Modello: 37373

Tipo: Manuale del proprietario

Questo manuale è adatto anche per

Assembly InstructionsAssembly Instructions

0192310R2 Page 1 of 3

Assembly InstructionsAssembly Instructions

Important

Before you begin, read and comply with all safety and operating instructions,

and ensure all parts and correct quantities are included.

Any parts damaged during shipment must be reported within 5 days of receipt.

To report information regarding missing parts or damage, to purchase parts

or accessories, or if you have any questions, please contact us.

www.spectrumfurniture.com

800-235-1262, 715-723-6750

Thank you for purchasing Spectrum products!

Freestanding Acrylic Divider PanelsFreestanding Acrylic Divider Panels

(4) or (2) 0158792

1” Gasket

2. Two-panel adder assembly2. Two-panel adder assembly

1. Orient the adder rear panel with tabs pointing down. Figure 2.

2. Insert the adder rear panel tabs into the side panel slots (of the previously

assembled three-panel divider) and push down to lock in place.

3. Hook the adder rear panel tabs over the adder side panel tabs and

push down to lock in place.

Figure 2

Rear Panel

Three-panel dividers

(W x D x H)

37374 - 24” x 24” x 16”

37376 - 24” x 24” x 24”

37378 - 30” x 24” x 16”

37380 - 30” x 24” x 24”

Two-panel adders

(W x D x H)

37375 - 24” x 24” x 16”

37377 - 24” x 24” x 24”

37379 - 30” x 24” x 16”

37381 - 30” x 24” x 24”

Three-panel

divider

Adder rear panel

Rear Panel

Side Panel

Adder side panel

1. Three-panel divider assembly1. Three-panel divider assembly

1. Orient the side panels with tabs pointing down. Figure 1.

2. Orient the rear panel with tabs pointing up.

3. Hook the side panel tabs over the rear panel tabs and push down

to lock in place.

Figure 1

Rear panel

Side panel

Two-panel

adder

Three-panel

divider

assembly

Side

panel

slots

0192310R2 Page 2 of 3

3. Install gaskets3. Install gaskets

1. Install gaskets on the bottom of the panels as shown. Figure 3.

Figure 3

Three-panel

divider

Two-panel

adder

Note: Do not ex or place excessive force on

the acrylic divider panels to avoid damage.

1” Gasket X 2

1” Gasket X 4

Other congurationsOther congurations

Figure 4

Rear panel

Side panel

Rear panel

Side panel

Rear panel

Side panel

0192310R2 Page 3 of 3

925 FIRST AVENUE, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM925 FIRST AVENUE, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM

Altuglas International 03-30-20 Page 1 of 1

Cleaning Recommendations for Plexiglas® Acrylic Sheet

Altuglas International routinely provides information on Cleaning Plexiglas® acrylic sheet and

the Chemical Resistance of Plexiglas® acrylic sheet to various chemicals. Altuglas

International does not provide any recommendation regarding disinfecting Plexiglas®

acrylic sheet.

Altuglas International recommends to CLEAN Plexiglas® acrylic sheet using soap and water.

Here is a link to our PLEXIGLAS® SHEET: Handling and Maintenance guidelines:

https://www.plexiglas.com/export/sites/plexiglas/.content/medias/downloads/plexiglas-expert-

pdf/Fabrication-Guidelines-Plexiglas-Handling-and-Maintenance.pdf

Wash Plexiglas® sheet with a mild soap or detergent and a lukewarm water solution. Use a clean

soft cloth or sponge and as much solution as possible. Rinse well. Dry by blotting with a damp

cloth or chamois.

Plexiglas® acrylic sheets have excellent CHEMICAL RESISTANCE to ammonia based and

chlorine based cleaners under ambient conditions for relatively short durations. Do not use

cleaners that contain alcohol. The chemical resistance of Plexiglas® acrylic sheet will vary with

the stress level, temperature, reagent, duration of exposure and specific Plexiglas® acrylic sheet

used in the application. Altuglas International recommends that parts made from Plexiglas®

acrylic sheets be tested with all reagents under appropriate conditions for the end-use application.

Differences between Cleaning and Disinfecting a surface1.

Cleaning refers to the removal of germs, dirt, and impurities from surfaces. Cleaning does not kill

germs, but by removing them, it lowers their numbers and the risk of spreading infection.

Disinfecting refers to using chemicals to kill germs on surfaces. This process does not necessarily

clean dirty surfaces or remove germs, but by killing germs on a surface after cleaning, it can

further lower the risk of spreading infection.

1 Cleaning and Disinfecting definitions copied from the CDC website: Clean & Disinfect; Interim Recommendations for US

Households with Suspected/Confirmed Coronavirus Disease 2019

(https://www.cdc.gov/coronavirus/2019-ncov/prepare/cleaning-disinfection.html) March 24, 2020. Altuglas International has never

tested any procedure or product to disinfect Plexiglas® acrylic sheet and has not independently verified any information provided

on the CDC website.

The statements, technical information and recommendations contained herein are believed to be accurate as of the date hereof. Since the

conditions and methods of use of the product and of the information referred to herein are beyond our control, Altuglas

International/Arkema expressly disclaims any and all liability as to any results obtained or arising from any use of the product or reliance

on such information; NO WARRANTY OF FITNESS FOR ANY PARTICULAR PURPOSE, WARRANTY OR MERCHANTABILITY

OR ANY OTHER WARRANTY EXPRESS OR IMPLIED, IS MADE CONCERNING THE GOODS DESCRIBED OR THE

INFORMATION PROVIDED HEREIN. The information provided herein relates only to the specific product designated and may not be

applicable when such product is used in combination with other materials or in any process. The user should thoroughly test any

application before commercialization. Nothing contained herein constitutes a license to practice under any patent and it should not be

construed as an inducement to infringe any patent and the user is advised to take appropriate steps to be sure that any proposed use of the

product will not result in patent infringement. Plexiglas® is a registered trademark belonging to Arkema.

Altuglas International – Sheet Division

Applications Development Lab

100 Route 413

Bristol, PA 19007