Yamaha ES Manuale del proprietario

Marca: Yamaha

Modello: ES

Categoria: Strumenti musicali

Tipo: Manuale del proprietario

Questo manuale è adatto anche per

SB168

Owner’s Manual

Bedienungsanleitung

Mode d’emploi

Manual de instrucciones

Manuale di istruzioni

SB168-ES Owner’s Manual

The top half of the above warning is located on the top or rear of the

unit.

Explanation of Graphical Symbols

The lightning ﬂash with arrowhead symbol

within an equilateral triangle is intended to alert

the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufﬁcient magnitude to

constitute a risk of electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and maintenance

(servicing) instructions in the literature

accompanying the product.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

ampliﬁers) that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug has

two blades and a third grounding prong. The wide blade

or the third prong are provided for your safety. If the

provided plug does not ﬁt into your outlet, consult an

electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

11 Only use attachments/accessories speciﬁed by the

manufacturer.

12 Use only with the cart, stand,

tripod, bracket, or table speciﬁed

by the manufacturer, or sold with

the apparatus. When a cart is

used, use caution when moving

the cart/apparatus combination to

avoid injury from tip-over.

13 Unplug this apparatus during

lightning storms or when unused for long periods of

time.

14 Refer all servicing to qualiﬁed service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or plug

is damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally,

or has been dropped.

(UL60065_03)

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR

MOISTURE.

SB168-ES Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical

shock, short-circuiting, damages, ﬁre or other hazards. These precautions include, but are not limited to, the following:

• Only use the voltage speciﬁed as correct for the device. The required voltage is

printed on the name plate of the device.

• Use only the included power cord.

If you intend to use the device in an area other than in the one you purchased,

the included power cord may not be compatible. Please check with your Yamaha

dealer.

• Do not place the power cord near heat sources such as heaters or radiators, and

do not excessively bend or otherwise damage the cord, place heavy objects on

it, or place it in a position where anyone could walk on, trip over, or roll anything

over it.

• Be sure to connect to an appropriate outlet with a protective grounding

connection. Improper grounding can result in electrical shock.

• Do not open the device or attempt to disassemble the internal parts or modify

them in any way. The device contains no user-serviceable parts. If it should

appear to be malfunctioning, discontinue use immediately and have it inspected

by qualiﬁed Yamaha service personnel.

• Do not expose the device to rain, use it near water or in damp or wet conditions,

or place containers on it containing liquids which might spill into any openings.

If any liquid such as water seeps into the device, turn off the power immediately

and unplug the power cord from the AC outlet. Then have the device inspected

by qualiﬁed Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

• If the power cord or plug becomes frayed or damaged, or if there is a sudden

loss of sound during use of the device, or if any unusual smells or smoke

should appear to be caused by it, immediately turn off the power switch,

disconnect the electric plug from the outlet, and have the device inspected by

qualiﬁed Yamaha service personnel.

• If this device should be dropped or damaged, immediately turn off the power

switch, disconnect the electric plug from the outlet, and have the device

inspected by qualiﬁed Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage

to the device or other property. These precautions include, but are not limited to, the following:

• Remove the electric plug from the outlet when the device is not to be used for

extended periods of time, or during electrical storms.

• When removing the electric plug from the device or an outlet, always hold the

plug itself and not the cord. Pulling by the cord can damage it.

• Before moving the device, remove all connected cables.

• When setting up the device, make sure that the AC outlet you are using is easily

accessible. If some trouble or malfunction occurs, immediately turn off the

power switch and disconnect the plug from the outlet. Even when the power

switch is turned off, electricity is still ﬂowing to the product at the minimum

level. When you are not using the product for a long time, make sure to unplug

the power cord from the wall AC outlet.

• If this device is to be mounted in an EIA-standard rack, carefully read the section

“Precautions for Rack Mounting” on page 7 before setting up the device.

Inadequate ventilation can result in overheating, possibly causing damage to the

device(s), or even ﬁre.

• Do not expose the device to excessive dust or vibrations, or extreme cold or heat

(such as in direct sunlight, near a heater, or in a car during the day) to prevent

the possibility of panel disﬁguration or damage to the internal components.

• Do not place the device in an unstable position where it might accidentally fall

over.

• Do not block the vents. This device has ventilation holes at the front and rear to

prevent the internal temperature from becoming too high. In particular, do not

place the device on its side or upside down. Inadequate ventilation can result in

overheating, possibly causing damage to the device(s), or even ﬁre.

• Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile

phone, or other electric devices. Doing so may result in noise, both in the device

itself and in the TV or radio next to it.

• Do not place the device in a location where it may come into contact with

corrosive gases or salt air. Doing so may result in malfunction.

• Before connecting the device to other devices, turn off the power for all devices.

Before turning the power on or off for all devices, set all volume levels to

minimum.

Power supply/Power cord

Do not open

Water warning

If you notice any abnormality

Power supply/Power cord

Location

Connections

(5)-6 1/2

SB168-ES Owner’s Manual

• When turning on the AC power in your audio system, always turn on the power

ampliﬁer LAST, to avoid speaker damage. When turning the power off, the power

ampliﬁer should be turned off FIRST for the same reason.

• Condensation can occur in the device due to rapid, drastic changes in ambient

temperature – when the device is moved from one location to another, or air

conditioning is turned on or off, for example. Using the device while

condensation is present can cause damage. If there is reason to believe that

condensation might have occurred, leave the device for several hours without

turning on the power until the condensation has completely dried out.

• Do not insert your ﬁngers or hands in any gaps or openings on the device

(vents, etc.).

•Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into any

gaps or openings on the device (vents, etc.) If this happens, turn off the power

immediately and unplug the power cord from the AC outlet. Then have the

device inspected by qualiﬁed Yamaha service personnel.

• Do not use the device for a long period of time at a high or uncomfortable

volume level, since this can cause permanent hearing loss. If you experience

any hearing loss or ringing in the ears, consult a physician.

• Do not rest your weight on the device or place heavy objects on it, and avoid use

excessive force on the buttons, switches or connectors.

• This device has a built-in backup battery that maintains data in internal memory

even when the device’s power is switched off. The backup battery will eventually

become depleted, however, and when that happens the contents of the internal

memory will be lost.* To prevent loss of data be sure to replace the backup

battery before it becomes fully depleted. Imminent battery depletion is indicated

by the panel LEDs, as described on page 21. In this case, immediately save the

data to a compatible digital mixer, then have qualiﬁed Yamaha service personnel

replace the backup battery. The average life of the internal backup battery is

approximately 5 years, depending on operating conditions.

* Data items maintained in the internal memory by the backup battery are as

follows:

• internal head ampliﬁer settings

Always turn the power off when the device is not in use.

The performance of components with moving contacts, such as switches, and connectors, deteriorates over time. Consult qualiﬁed Yamaha service personnel about replacing

defective components.

• The illustrations as shown in this manual are for instructional purposes only, and may be different from the ones on your equipment.

• EtherSound is a registered trademark of Digigram S.A.

• The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.

* Speciﬁcations and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or

speciﬁcations at any time without prior notice. Since speciﬁcations, equipment or options may not be the same in every locale, please check with your

Yamaha dealer.

Handling caution Backup battery

XLR-type connectors are wired as follows (IEC60268 standard): pin 1: ground, pin 2: hot (+), and pin 3: cold (-).

Yamaha cannot be held responsible for damage caused by improper use or modiﬁcations to the device, or data that is lost or destroyed.

European models

Purchaser/User Information speciﬁed in EN55103-1 and EN55103-2.

Inrush Current: 50A

Conforms to Environments: E1, E2, E3 and E4

(5)-6 2/2

SB168-ES Owner’s Manual

Foreword.............................................................................................................6

SB168-ES Features................................................................................................................. 6

Firmware Updates ................................................................................................................... 6

Connecting the AC Power Cable............................................................................................. 6

Powering ON or OFF............................................................................................................... 7

Precautions for Rack Mounting................................................................................................ 7

Recessed installation............................................................................................................... 7

Resetting the Unit to Initial Factory Condition (Initialization) ................................................... 7

About EtherSound .............................................................................................8

EtherSound is …...................................................................................................................... 8

Daisy Chain and Ring Networks.............................................................................................. 8

Controls and Functions...................................................................................10

Front Panel ............................................................................................................................ 10

Rear Panel............................................................................................................................. 11

System Examples ............................................................................................12

Daisy Chain Connection ........................................................................................................ 12

Ring Connection .................................................................................................................... 12

Setup .................................................................................................................13

About the AVS-ESMonitor Software...................................................................................... 13

Initial Setup Using the Quick Setup Function ........................................................................ 13

Individual Parameter Settings (Control Page) ....................................................................... 16

Setup Error Messages........................................................................................................... 17

Head Amp Control ...........................................................................................18

Control from a Digital Mixing Console ................................................................................... 18

Control From the AVS-ESMonitor Application....................................................................... 18

Head Amplifier Parameters That Can be Monitored and Controlled ..................................... 19

Troubleshooting...............................................................................................20

Troubleshooting..................................................................................................................... 20

Messages .............................................................................................................................. 21

References......................................................................................................167

General Specification........................................................................................................... 167

Input/Output Characteristics ................................................................................................ 167

Electrical Characteristics ..................................................................................................... 168

Dimensions.......................................................................................................................... 169

Compatible Host List............................................................................................................ 169

Included Accessories

• Owner’s Manual

•AC Power Cable

Contents

SB168-ES Owner’s Manual

Foreword

Thank you for choosing the Yamaha SB168-ES Stage Box. The SB168-ES is an Ether-

Sound capable stage box with 16 analog inputs and 8 analog outputs. In order to take

full advantage of the features and performance offered by the SB168-ES, be sure to

read this owner’s manual carefully before operation.

SB168-ES Features

■ Long-distance EtherSound Network Capability

Audio can be transferred over distances up to 100 meters* between devices via standard Ethernet cables using the Ether-

Sound network protocol. The SB168-ES can be used as a general-purpose analog I/O box. Supported sampling rates are

44.1 kHz and 48 kHz (88.2 kHz and 96 kHz are not supported).

* Maximum practical distance may vary according to the cable used.

■ Remotely Controllable Internal Head Ampliﬁers

Internal head ampliﬁer parameters can be remotely controlled from a compatible digital mixing console or from the AVS-

ESMonitor application running on a computer.

■ Up to Four SB168-ES Units* Can Be Used for Expanded I/O

Up to four SB168-ES units can be used to provide a total of 64 inputs and 32 outputs.

* The maximum number of units that can be used may depend on the digital mixing console used.

Firmware Updates

Two types of ﬁrmware are required: ﬁrmware for the SB168-ES unit itself, provided by Yamaha, and EtherSound ﬁrmware pro-

vided by AuviTran.

The SB168-ES ﬁrmware can be updated from a computer connected to the rear-panel NETWORK connector. Information

about the latest versions and ﬁrmware downloads are available at the Yamaha pro audio website SB168-ES product page:

http://www.yamahaproaudio.com/products

The EtherSound ﬁrmware can be updated from a computer connected to the EtherSound connector.

Information about the latest versions and ﬁrmware downloads are available at the AuviTran website:

http://www.auvitran.com/

Connecting the AC Power Cable

• Before connecting the power cable, make sure that the power switches of all devices are turned OFF.

First connect the supplied power cable to the socket on the rear panel of the SB168-ES, then connect the AC plug to an appro-

priate AC power outlet (make sure the local supply voltage matches the rated AC voltage of the unit).

CAUTION

SB168-ES Owner’s Manual

Powering ON or OFF

•To prevent loud noise bursts from the speakers when powering up the system, turn devices on in the following order:

audio sources, SB168-ES, digital mixer, and ﬁnally power ampliﬁers. Reverse this order when turning the system off.

1. Press the [POWER] switch to turn the unit ON.

2. Press the [POWER] switch a second time to turn the unit OFF.

• The unit consumes a very small “standby” voltage even when the power switch is turned OFF. Be sure to unplug the AC

power cable if the unit will not be used for an extended period of time.

• Rapidly turning the unit ON and OFF in succession can cause it to malfunction. After turning the unit OFF, wait for about

6 seconds before turning it ON again.

Precautions for Rack Mounting

This unit is rated for operation at ambient temperatures ranging from 0 to 40 degrees Celsius. When mounting the unit with

other SB168-ES unit(s) or other device(s) in an EIA standard equipment rack, internal temperatures can exceed the speciﬁed

upper limit, resulting in impaired performance or failure.

Always observe the following when rack mounting the unit:

• If three or more SB168-ES units are mounted without space in the same rack, set the fan speeds to HIGH.

• If multiple SB168-ES units are mounted in the same rack with their fan speeds set to LOW, leave a 1U rack space between

every two units. Also either leave the open spaces uncovered or install appropriate ventilating panels to minimize the possi-

bility of heat buildup.

• When mounting the unit in a rack with devices such as power ampliﬁers that generate a signiﬁcant amount of heat, leave

more than 1U of space between the SB168-ES and other device. Also either leave the open spaces uncovered or install appro-

priate ventilating panels to minimize the possibility of heat buildup.

•To ensure sufﬁcient airﬂow, leave the rear of the rack open and position it at least 10 centimeters from walls or other surfaces.

If the rear of the rack can’t be left open, install a commercially available fan or similar ventilating option to secure sufﬁcient

airﬂow. If you’ve installed a fan kit, there may be cases in which closing the rear of the rack will produce a greater cooling

effect. Refer to the rack and/or fan unit manual for details.

Recessed installation

If you want to recess the front panel surface of the device from the front edge of the rack, you can adjust the position of the rack

mount brackets to recess the device by 50mm or 100mm.

• When you install the brackets, use the same screws that you just removed.

Resetting the Unit to Initial Factory Condition (Initialization)

This operation initializes the internal backup memory, resetting all head ampliﬁer parameters to the original factory settings.

1. Turn the power OFF.

2. Move front-panel DIP switches 6 and 8 down to

the ON position, then turn the power ON.

Initialization will take about one second.

When initialization is complete all [PEAK] indicators

on the front panel will ﬂash. At the same time the OUT

[TX]/IN [RX] indicators will ﬂash and the IN [TX]

indicator will light.

3. Turn the power OFF, return DIP switches 6 and

8 to their original positions, then turn the power

ON again.

CAUTION

NOTE

SB168-ES Owner’s Manual

About EtherSound

EtherSound is an audio networking protocol developed by Digigram in France. EtherSound allows up to 64 channels of uncom-

pressed 24 bit/48 kHz audio to be bi-directionally transferred – 64 channels downstream plus 64 channels upstream – over a

single CAT5e Ethernet cable. Up to 32 channels of 24 bit audio can be transferred when the sample rate is 96 kHz. Remote con-

trol signals for head ampliﬁers and other devices can be transferred simultaneously with the audio signals.

Signals can be transferred over distances of up to 100 meters* between devices. Even greater distances can be covered if media

converters are used to convert the signals to optical ﬁber format.

* Dependent on cable quality. Refer to the website listed below for details.

http://www.ethersound.com/

Latency when transferring 48 kHz signals is 5 samples (104µsec), increasing by 1.4 µsec for each device added to the network

(including network switches). EtherSound is the ideal choice for systems in which minimal latency is a priority.

The AVS-ESMonitor software application for Windows platforms that allows setup and monitoring of devices connected to an

EtherSound network is available from the AuviTran website at no charge.

http://www.auvitran.com/

The most basic type of connection used for EtherSound networks is the serial “Daisy Chain.” Daisy chain networks allow 64

channels of audio to be independently transferred in both the downstream and upstream directions simultaneously. In this case

the top device in the chain is the word clock master, known as the “Primary Master.”

EtherSound is …

Daisy Chain and Ring Networks

OUT IN

Computer

Primary Master

EtherSound

Device

EtherSound

Device

EtherSound

Device

Upstream: 64 Channels

Downstream: 64 Channels

SB168-ES Owner’s Manual

About EtherSound

It is also possible to use network switches to distribute the signals to multiple devices. In this case devices connected directly

to the network switch cannot send signals in the upstream direction.

If a connection is broken in a daisy chain network, the signal ﬂow is interrupted at that point and no signal will be transferred

beyond that point. This weakness can be overcome by connecting the ends of a daisy chain network to form a ring that provides

signal redundancy. In this type of “Ring” network a problem at one point in the network will not affect operation of the entire

network. The compromise is that ring networks are limited to a total of 64 audio channels. It is also necessary to use Ether-

Sound devices that support ring network connection (the SB168-ES does support ring networks). Network switches and similar

devices cannot be used in a ring network.

•For detailed information on EtherSound, refer to the EtherSound website: http://www.ethersound.com/, and the “EtherSound

Setup Guide” at the Yamaha pro audio website SB168-ES product page: http://www.yamahaproaudio.com/products/

OUT

EtherSound

Device

Network Switch

EtherSound

Device

Downstream Only

EtherSound

Device

EtherSound

Device

OUT ININ OUT OUTIN

EtherSound

Device

EtherSound

Device

EtherSound

Device

64 Channels Total Downstream & Upstream

NOTE

SB168-ES Owner’s Manual

Controls and Functions

q INPUT 1–16 Connectors

These are the XLR-3-31 type analog connectors for the 16

input channels. The input level range is from -62 dBu to +10

dBu. +48V phantom power can be supplied to devices that

require it via the input connectors.

• The PAD will be switched on or off internally when the

gain of the SB168-ES internal head amp is adjusted

between -14 dB and -13 dB. Keep in mind that noise

may be generated if there is a difference between the

Hot and Cold impedance of the external device con-

nected to the INPUT connector when using phantom

power.

w +48V Indicators

These indicators light when +48V phantom power is turned

ON for the corresponding input channels. Phantom power

supply switching can be carried out from a compatible digi-

tal mixing console or computer application. No phantom

power will be supplied, however, if the [+48V MASTER]

switch is OFF, even if phantom power to individual channels

is turned ON (the +48V indicators will still light). The +48V

indicators also function as error indicators: the indicators for

all channels will ﬂash if an error occurs.

• Make sure that phantom power is turned OFF unless

it is needed.

• When turning phantom power ON, make sure that no

equipment other than phantom-powered devices

such condenser microphones are connected to the

corresponding INPUT connectors. Applying phantom

power to a device that does not require phantom

power can damage the device.

• Do not connect or disconnect a device to an INPUT

while phantom power is applied. Doing so can dam-

age the connected device and/or the unit itself.

•To prevent possible damage to speakers, make sure

that power ampliﬁers and/or powered speakers are

turned OFF when switching phantom power ON or

OFF. We also recommend setting all digital mixing

console output controls to minimum when turning

phantom power ON or OFF. Sudden high level peaks

caused by the switching operation can damage

equipment as well as the hearing of those present.

e SIG Indicators

These indicators light green when the signal applied to the

corresponding channel reaches or exceeds -34 dBFS. The

SIG indicators also function as error indicators: the indica-

tors for all channels will ﬂash if an error occurs.

r PEAK Indicators

These indicators light red when the signal level of the corre-

sponding channel reaches or exceeds -3 dBFS. The PEAK

indicators also function as error indicators: the indicators for

all channels will ﬂash if an error occurs (and during initial-

ization).

t EtherSound [IN]/[OUT] Connectors

The SB168-ES can be connected to other EtherSound devices

via these RJ-45 connectors using standard Ethernet cables

(CAT5e or better recommended). [IN] and [OUT] connectors

are provided to allow daisy chain or ring connection.

• The use of Ethernet cables with Neutrik etherCON®

CAT5 compatible RJ-45 plugs is recommended. Stan-

dard RJ-45 plugs can also be used.

• Use STP (shielded twisted pair) cable to prevent elec-

tromagnetic interference. Make sure that the metal

parts of the plugs are electrically connected to the STP

cable shield by conductive tape or comparable means.

• Refer to the following EtherSound website for the length

of cable that can be used.

http://www.ethersound.com/

y IN/OUT [TX]/[RX] Indicators

The appropriate indicator ﬂashes when data is transmitted

from (TX) or received at (RX) the EtherSound [IN]/[OUT]

connectors.

These indicators will also light and/or ﬂash to display errors,

warnings, and information as described on page 21.

• All four indicators will ﬂash when the [Identify] button in

the AVS-ESMonitor application (page 16) is clicked,

and will continue to ﬂash until the button is clicked a

second time.

Front Panel

u i o !0y

wer

NOTE

CAUTION

NOTE

SB168-ES Owner’s Manual

Controls and Functions

u DIP Switches 1–8

Switches 1–4 of this 8-bit DIP switch are used to set the

Setup ID as described on page 14.

i [+48V MASTER] Switch

This is the master switch for the unit’s +48V phantom power

supply. If the [+48V MASTER] switch is off no phantom

power will be supplied to the unit’s input connectors even if

the individual input phantom power settings are ON. How-

ever, the +48 indicators will light on channels for which

phantom power is turned ON even if the [+48V MASTER]

switch is OFF.

o Power Indicator

Lights when AC power to the unit is ON.

!0 [POWER] Switch

Turns power to the unit ON or OFF. Internal head ampliﬁer

settings such as gain, high-pass ﬁlter, etc., are retained in

memory even when the power is OFF.

!1 OUTPUT 1–8 Connectors

These eight XLR-3-32 type connectors deliver analog output

from the unit’s corresponding output channels. Nominal out-

put level is +4 dBu.

q Earth Screw

For maximum safety, please earth the unit properly. The sup-

plied AC power cable is a 3-wire type, so if the AC outlet

used is properly earthed the SB168-ES will be earthed as

well. If the AC outlet used is not earthed, however, please

use the earth screw to earth the unit. In addition to maximiz-

ing safety, proper earth connection also effectively mini-

mizes hum and interference.

w [AC IN] Socket

Connect the supplied AC power cable here. First connect the

AC power cable to the socket on the SB168-ES rear panel,

then plug it into an appropriate AC power outlet.

• Use only the supplied AC power cable. The use of an

inappropriate cable can result in equipment failure,

overheating, or even ﬁre.

e NETWORK Connector

An Ethernet cable can be connected from a computer to this

connector to allow updating the unit’s ﬁrmware.

• Use STP (shielded twisted pair) cable to prevent elec-

tromagnetic interference (USA, Canada, and Europe).

• Since the SB168-ES supports MDI/MDI-EX, either a

straight or cross Ethernet cable can be used.

r [FAN] Switch

Sets the internal cooling fan to operate at either HIGH or

LOW speed. This switch is set to LOW when the unit is ini-

tially shipped from the factory. As long as the unit is oper-

ated within the speciﬁed ambient temperature range either

the LOW or HIGH setting can be used. The HIGH setting is

recommended if the ambient temperature is high, if the unit

is in direct sunlight even if the ambient temperature is within

the speciﬁed operating range, and in any situation in which

fan noise is not a problem.

If two or more SB168-ES units are mounted in the same rack

and the fan speed is set to LOW, leave a 1U rack space

between every two units. Also either leave the open rack

spaces uncovered or install appropriate ventilating panels to

minimize the possibility of heat buildup. If three or more

SB168-ES units are mounted without space in the same

rack, set the fan speeds to HIGH.

Rear Panel

e r

q w

WARNING

NOTE

SB168-ES Owner’s Manual

System Examples

In this example an MY16-ES64 EtherSound interface card is installed in a Yamaha M7CL or LS9 digital mixing console and

connected to multiple SB168-ES units. In this type of system an MY16-EX I/O expansion card is also required for each addi-

tional SB168-ES unit connected in the daisy chain (i.e. for three SB168-ES units one MY16-ES64 card and two MY16-EX

cards are required).

The EtherSound [OUT] connector on the MY16-ES64 card is connected to the [IN] connector of the ﬁrst SB168-ES unit, and

subsequent units are daisy chained as shown in the diagram. A computer can be connected to the EtherSound [IN] connector on

the MY16-ES64 card functioning as Primary Master.

As in the daisy chain example above, an MY16-ES64 EtherSound interface card is used to connect the digital mixing console to

the SB168-ES units. The EtherSound [OUT] connector is connected to the EtherSound [IN] connector of the subsequent unit,

and the EtherSound [OUT] connector of the ﬁnal SB168-ES unit is connected back to the EtherSound [IN] connector of the

MY16-ES64 card.

• In ring connections it is particularly important to ensure that all EtherSound devices are running the latest ﬁrmware (page 6).

Daisy Chain Connection

Daisy Chain Characteristics

•Four daisy chained SB168-ES units provide a total of 64 input channels and 32 output channels.

• The computer can remain connected at all times, making it possible to use the AVS-ESMonitor application to control the SB168-ES head ampli-

ﬁers and continuously monitor the EtherSound network.

• If a connection is broken in a daisy chain network, the signal ﬂow is interrupted at that point and no signal will be transferred beyond that point.

Ring Connection

Ring Connection Characteristics

• The EtherSound speciﬁcations limit the total number of input and output channels to 64 in this type of network.

• The AVS-ESMonitor application cannot be used during system operation. An EtherSound device with a third port is required to connect a com-

puter running AVS-ESMonitor into the ring.

•A problem at one point in the network will not affect operation of the entire network.

MY16-ES64

MY16-EX

Computer

Yamaha Mixing Console

SB168-ES (ID #1)

Inputs: CH 1–16

Outputs: CH 1–8

OUTIN IN

OUTIN

EtherSound

SB168-ES (ID #2)

Inputs: CH 17–32

Outputs: CH 9–16

SB168-ES (ID #3)

Inputs: CH 33–48

Outputs: CH 17–24

OUTIN

MY16-ES64

MY16-EX

Yamaha Mixing Console

SB168-ES (ID #1)

Inputs: CH 1–16

Outputs: CH 1–8

OUTIN IN

OUTIN

EtherSound

SB168-ES (ID #2)

Inputs: CH 17–32

Outputs: CH 9–16

SB168-ES (ID #3)

Inputs: CH 33–48*

Outputs: None*

* Channel assignments can

be changed as required

within a range of 64 input

and output channels, total.

OUTIN OUT

NOTE

SB168-ES Owner’s Manual

Setup

AVS-ESMonitor is a software application from the Auvitran company that allows monitoring and control of EtherSound net-

works. It can be used to make input/output assignments and set the EtherSound parameters as required. Please download the

AVS-ESMonitor application from the website listed below. AVS-ESMonitor versions 3.4.6 and later support the SB168-ES.

http://www.auvitran.com/

Initial SB168-ES setup can be performed quickly and easily using the AVS-

ESMonitor Quick Setup function. The Quick Setup function provides the fol-

lowing capabilities:

• Sets up necessary EtherSound settings for the SB168-ES and MY16-ES64.

EtherSound devices other than the SB168-ES and MY16-ES64 are not

affected, but patches to those other EtherSound devices will be cleared.

• Support for up to four SB168-ES units connected to an MY16-ES64.

• The Quick Setup function cannot be used if two or more MY16-ES64 cards

are connected to the network. To connect multiple SB168-ES units, add one

MY16-EX card for each additional SB168-ES unit added to the network

(an MY16-EX card is not required for the ﬁrst or only SB168-ES unit in a

network).

• After the Quick Setup function is executed, as long as the network connec-

tions are not changed there is no need to perform the Quick Setup proce-

dure again. However, if the number and/or order of the SB168-ES units are

changed, or the connected devices (SB168-ES, MY16-ES64) are replaced,

it will be necessary to perform the Quick Setup operation again.

The Quick Setup function cannot be used when EtherSound cards from other manufacturers are used. In such a case the neces-

sary initial parameters must be set up manually: refer to “Individual Parameter Settings (Control Page)” on page 16 for details.

When connecting with the M7CL-48ES, the Auto Conﬁgure function can apply the patch settings automatically without the

AVS-ESMonitor application. The latest ﬁrmware for the SB168-ES will be required in this case.

1. Determine the source for head ampliﬁer parame-

ter control:

A. MY16-ES64 Slot Internal Connection (LS9)

Use this option is for digital mixing consoles such

as the LS9 that don’t have a 9-pin D-sub “HA

REMOTE” connector.

B. MY16-ES64 D-sub 9-pin Connection

Use this option for digital mixing consoles such as

the M7CL or digital mixing engines such as the

DME64N or DME24N that have a 9-pin D-sub

“HA REMOTE connector.

C. AVS-ESMonitor

• Refer to page 169 to determine whether your digi-

tal mixing console can be used to control the

SB168-ES.

2. Turn the power to all devices OFF.

3. Set the switches on the MY16-ES64 and MY16-

EX circuit boards.

• If you selected option B in step 1, set the SW1

switch on the MY16-ES64 to [422].

• Set the SW2 switch on the MY16-ES64 to [48K].

• When one or more MY16-EX cards are to be used,

SW1 on the MY16-EX sets the ID number. ID

numbers should be assigned in sequence, corre-

sponding to the order the cards are to be connected

to the MY16-ES64.

• Set the SW2 switches on all MY16-EX cards to

[48K].

About the AVS-ESMonitor Software

Initial Setup Using the Quick Setup Function

Preparation

NOTE

SW1

232 422

SW248K

96K

MY16-ES64

SW1 SW2

SW2SW1

96K48K321

MY16-EX

SB168-ES Owner’s Manual

Setup

4. Install the MY16-ES64 and MY16-EX cards in

the digital mixing console’s slots, then connect

the required Ethernet cables.

•For details on installing and connecting the cards,

refer to instructions provided with each product.

• When installing an MY16-ES64 card in an LS9-32

console, install the card in SLOT 1.

5. Set the ID of each SB168-ES unit via the DIP

switches (1–4) in the order they are connected,

taking care not to duplicate any of the ID set-

tings.

The DIP switch corresponding to the desired ID num-

ber should be moved to it’s “down” (ON) position. All

other switches should remain in their “up” positions.

6. Make the required daisy chain connections

between the MY16-ES64 card and the SB168-ES

units.

• When setting up a ring type network, initial set-

tings should be made with the system connected

as a daisy chain. Close the ring connection after

the initial settings have been made.

Connect the computer to the MY16-ES64 Ether-

Sound [IN] connector.

8. If you selected option B in step 1, connect the dig-

ital mixing console’s [REMOTE] connector to the

MY16-ES64 card [HA REMOTE] connector via

a 9-pin D-sub cross cable.

9. Turn the power to all devices ON.

10.

Select the word clock master on the digital mix-

ing console. For a daisy chain network select

either [INT48K] or [INT44.1K], and for a ring

network select the [1/2] channel of the slot in

which the MY16-ES64 card is installed.

11.

If you selected option A in step 1, and are using

an LS9-32 console, select [SLOT 1] via the con-

sole’s EXTERNAL HA display COMM PORT

parameter.

1. Launch the AVS-ESMonitor application in online

mode.

• If the AVSMonitor application has been launched

in ofﬂine mode, it can be switched to online mode

by clicking [Switch ofﬂine mode] in the [Com-

mand] menu.

Click [Reset networks] in the [Command] menu.

3. In the tree views select one of the SB168-ES units

on the network.

4. Open the Control tab.

5. Select the control source determined in the previ-

ous section via the Quick Setup Head Amp Con-

troller ﬁeld.

6. Select the EtherSound network connection type

via the Network Mode ﬁeld.

NOTE

Example: Setup ID = 1

NOTE

Setup Procedure

NOTE

Quick Setup

Control TabTree Views

SB168-ES Owner’s Manual

Setup

7. If a ring network is to be used, use the Channel

Allocation slider to select an input/output chan-

nel combination. The possible combinations are

as follows:

In ring networks the total number of input and output

channels is limited to 64. If the network includes only

one or two SB168-ES units you can select from 32

Inputs/32 Outputs to 48 Inputs/16 Outputs without

exceeding the limitation. If three or four SB168-ES

units are connected you will need to decide whether to

give priority to inputs or outputs. For example, you

could select 64 Inputs/0 Outputs if you want to use all

available input channels, or 32 Inputs/32 Outputs if you

want to use all available output channels.

8. Click the [APPLY] button, then click the [OK]

button in response to the conﬁrmation dialog that

appears.

9. If the Quick Setup operation has completed suc-

cessfully a “Quick Setup is done successfully”

message will appear.

The Quick Setup ﬁelds will return to their initial state

when the Quick Setup operation has ﬁnished.

10.

If you are setting up a ring network, disconnect

the computer from the MY16-ES64 card Ether-

Sound [IN] connector, and connect the Ether-

Sound [OUT] connector on the last SB168-ES

unit in the chain back to the EtherSound [IN]

connector on the MY16-ES64 card to complete

the ring.

When four SB168-ES units are daisy chained, their input

channels are assigned to MY16-ES64 input channels 1–64 in

order from the ﬁrst SB168-ES unit in the chain (Setup ID

#1) as follows: 1–16, 17–32, 33–48, 49–64. The MY16-

ES64 output channels are assigned to the SB168-ES outputs

in the same way: 1–8, 9–16, 17–24, 25–32.

In a ring network the input and output channels are assigned

in sequence from the ﬁrst to last SB168-ES unit within the

maximum 64-channel limitation, according to the number of

SB168-ES units used and the Channel Allocation setting.

• As long as the network connections are not changed

there is no need to perform the Quick Setup procedure

again. However, if the number and/or order of the

SB168-ES units are changed, or the connected devices

(SB168-ES, MY16-ES64) are replaced, it will be neces-

sary to perform the Quick Setup operation again.

• If other types of EtherSound devices are connected, or

the channel assignments are to be changed, it will be

necessary to set the appropriate parameters individu-

ally via the AVS-ESMonitor application. Refer to “Indi-

vidual Parameter Settings (Control Page)” on page 16

and/or the AVS-ESMonitor operation manual for details.

• Set up the digital mixing console input patching in

sequential 8-channel groups for the slot inputs (CH1–8,

CH9–16, etc.). This makes it easy to select input chan-

nels on the external SB168-ES units for remote head

ampliﬁer control.

• When the Quick Setup function is executed the settings

are saved to non-volatile memory in EtherSound

devices on the network, overwriting any previous data.

Since the previous data is overwritten and thereby

erased, you might want to save important settings

before executing the Quick Setup function via the [Save

As] command in the [File] menu.

Inputs

(No. of Input Channels)

32 40 48 56 64

Outputs

(No. of Output Channels)

32 24 16 8 0

NOTE

SB168-ES Owner’s Manual

Setup

When connecting to devices that are not supported by the Quick Setup function, or when you need to make changes to speciﬁc

EtherSound settings, the parameters in the AVS-ESMonitor Control page provide access to head ampliﬁer control settings while

those in the Net Patch and I/O Patch pages provide access to the input an output channel settings. Refer to the AVS-ESMonitor

manual for details on the Net Patch and I/O Patch pages.

Synchro Status

Displays the current EtherSound network synchronization

status.

Error Status

Displays SB168-ES error messages. The indicators on the

SB168-ES indicate the type of error by the way they ﬂash or

light, while speciﬁc error messages are displayed here.

Lock Routing

This parameter makes it possible to temporarily lock editing

of the patches in the I/O Patch page, preventing possible

operation errors. “Lock Inputs” locks the IN > ES patches,

while “Lock Outputs” locks the OUT < ES patches.

Input Signal Peak/Output Signal Peak

Signal and peak indicators for the input and output channels.

The upper row is the PEAK indicators, which light red, and

the lower row is the SIGNAL indicators, which light green.

Serial Communication Mode

Select [Unicast] when controlling the head ampliﬁers from a

compatible digital mixing console, and select the MY16-

ES64 card as the communication target. It is also necessary

to set the MY16-ES64 Serial Communication Mode.

Select [Slave] when controlling the head ampliﬁers directly

from the AVS-ESMonitor application.

The [Multicast] setting is provided for future expansion, and

is not currently available.

Head Amp Remote Option

When controlling the head ampliﬁers from the AVS-ESMon-

itor application, a Head Amp page that provides access to

the head ampliﬁer control parameters will be added to the

interface if the [Head Amp PC Remote Control] checkbox is

checked after selecting [Slave] in the Serial Communication

Mode section.

Tools

When the [Identify] button is clicked the SB168-ES IN/OUT

[TX]/[RX] indicators will ﬂash, and will continue to ﬂash

until the button is clicked a second time.

Emergency Clock

If the EtherSound network is used in a ring conﬁguration,

turn this checkbox ON to prevent audio interruptions when a

connection in the ring is broken. If Emergency Clock is OFF,

audio will be interrupted.

For daisy chain conﬁgurations, if the SB168-ES is the pri-

mary master, turn this checkbox OFF to select the SB168-ES

internal word clock or ON to use the EtherSound module

word clock. If the SB168-ES is not primary master, the

Emergency Clock checkbox has no effect.

• See page 13 for information on the Quick Setup func-

tion.

Settings from DIP Switch 5–8 (for M7CL-48ES)

These are the settings for use when connecting with the

M7CL-48ES using the Auto Conﬁgure function. The set-

tings of “Network Mode” and “Unicast Tunneling to” are

displayed by scanning the status of the DIP switches 5–8

when the power is turned ON.

When you want to temporarily change the EtherSound set-

tings (including “Network Mode” and “Unicast Tunneling

to”) in the AVS-ESMonitor application, turn the Auto Con-

ﬁgure checkbox OFF.

Individual Parameter Settings (Control Page)

NOTE

SB168-ES Owner’s Manual

Setup

If any of the error messages listed below appears while executing the Quick Setup function, resolve the problem as required and

then execute Quick Setup again.

When changing a Setup ID setting be sure to turn the device’s power OFF, change the DIP switch settings as required, and then

turn the device ON again.

Setup Error Messages

Error Message Details and Solution

Setup ID is discontinuous. Setup ID #n not

found.

The Setup ID numbers are not sequential—ID “#n” is missing.

Referring to the “Preparation” instructions on page 13, use the DIP switches to set the

Setup ID numbers in sequence beginning from #1.

There are two or more with same Setup ID

#n. (ﬂashing)

Two or more SB168-ES units have the same Setup ID number.

When duplicate Setup ID numbers are detected the SB168-ES IN/OUT [TX]/[RX] indi-

cators will ﬂash. Referring to the “Preparation” instructions on page 13, check the DIP

switch settings and make sure that each unit has a unique Setup ID.

There are two or more MY16-ES64(s). (ﬂash-

ing)

Two or more MY16-ES64 cards have been detected on the EtherSound network.

The use of two or more MY16-ES64 cards is not supported by the Quick Setup func-

tion. The IN/OUT [TX]/[RX] indicators of the MY16-ES64 cards will ﬂash. Redo the

connections so that only one MY16-ES64 is connected to the network.

MY16-ES64 is not found in ES network. No MY16-ES64 card can be located on the EtherSound network.

EtherSound interface cards other than the MY16-ES64 are not supported by the

Quick Setup function.

MY16-ES64 is not Primary Master. (ﬂashing) The MY16-ES64 is not functioning as Primary Master in a daisy chain network.

This type of conﬁguration is not supported by the Quick Setup function. The IN/OUT

[TX]/[RX] indicators of the MY16-ES64 card will ﬂash while this error message is dis-

played. Redo the connections so that the MY16-ES64 functions as Primary Master.

Setup ID of all SB168-ES is not assigned. The Setup ID has not been set for any of the SB168-ES units on the EtherSound net-

work. The Setup ID for at least one unit must be set.

The IN/OUT [TX]/[RX] indicators of the SB168-ES units will ﬂash while this error mes-

sage is displayed. Referring to the “Preparation” instructions on page 13, set the

Setup ID numbers of the connected SB168-ES units.

No error will occur if the Setup ID is not set for one of the SB168-ES units in a multi-

unit system, but the patch settings for that SB168-ES unit will be cleared.

MY16-ES64 is not 48kHz. 96kHz is selected. The sampling frequency of the MY16-ES64 card connected to the EtherSound net-

work is set to 96 kHz (SW2).

The SB168-ES does not support 88.2 kHz or 96 kHz sampling frequencies.

The IN/OUT [TX]/[RX] indicators of the MY16-ES64 card will ﬂash while this error

message is displayed. Referring to the “Preparation” instructions on page 13, set the

SW2 switch on the MY16-ES64 card to [48K].

The power supply was turned off or the cable

was disconnected.

The power to one of the devices connected to the EtherSound network was turned off,

or a cable was disconnected during Quick Setup execution.

Check the power cables and power switch settings of all devices and execute the

Quick Setup function again.

Audio routing locked on device. (ﬂashing) The Quick Setup function cannot be executed if the Lock Routing parameter in the

Control page is ON.

The IN/OUT [TX]/[RX] indicators of the MY16-ES64 card and SB168-ES units will

ﬂash while this error message is displayed.

In order to execute the Quick Setup function all Lock Routing parameters must be

turned OFF.

SB168-ES Owner’s Manual

Head Amp Control

The SB168-ES head ampliﬁers can be remotely controlled from host devices such as a compatible digital mixing

console or digital mixing engine (see page 169), or from the AVS-ESMonitor application.

The SB168-ES head ampliﬁers can be controlled from a compatible digital mixing console. In order to control the head ampli-

ﬁers from a digital mixing console, select control via an MY16-ES64 in the Quick Setup Head Amp Controller ﬁeld.

Each SB168-ES unit will be represented by two AD8HR units (AD8HR #1, AD8HR #2, etc.) on the digital mixing console dis-

play, and the SB168-ES parameters can be controlled in the same way as AD8HR parameters. Furthermore, scene recall can be

used to recall all head ampliﬁer settings at once.

Refer to the digital mixing console owner’s manual for details on head ampliﬁer control.

• SB168-ES error messages are not shown on the digital mixing console display, and EtherSound

parameters cannot be set from the digital mixing console. Use the AVS-ESMonitor software application

for these functions.

The AVS-ESMonitor application can be used both to set EtherSound parameters and control the SB168-ES head ampliﬁers. To

control the head ampliﬁers from the AVS-ESMonitor application, either select AVS-ESMonitor in the Quick Setup Head Amp

Controller ﬁeld or perform the setup procedure described below and a Head Amp page will be added to the AVS-ESMonitor

interface.

1. Select the SB168-ES to be controlled in the tree views.

• If multiple SB168-ES units are to be controlled, repeat the procedure described below for each one.

2. Select [Slave] in the Serial Communication mode section.

Check each Control page and make sure that no other EtherSound device is

assigned to transmit to this SB168-ES unit. If the SB168-ES is selected, tempo-

rarily switch to the [Slave] setting.

3. Check the [Head Amp PC Remote Control] Checkbox.

A Head Amp tab will appear.

Control from a Digital Mixing Console

Model Section Title in Owner’s Manual

M7CL, LS9 Using an external head amp

DM1000 Using the AD8HR/AD824

DM2000 Controlling AD8HR/AD824 A/D Converters

PM5D/PM5D-RH Reference section: SYS/W.CLOCK function—HA (Head Amp) screen

DME64N/24N Controlling external head ampliﬁers from the DME64N/24N, Head Ampliﬁer Setup (HA) Page

Control From the AVS-ESMonitor Application

NOTE

SB168-ES Owner’s Manual

Head Amp Control

4. Click the Head Amp Tab.

It can take a few seconds for the channel name in the Ch Selection ﬁeld to appear.

The head ampliﬁer parameters can be controlled from this display. The current parameter settings will be shown on the display

when “ch 1-8” or “ch 9-16” is selected from the Ch Selection ﬁled.

• If you later decide to switch back to controlling the head ampliﬁers from a digital mixer, we recommend

executing the Quick Setup function again, although the same result can be achieved by un-checking

the [Head Amp PC Remote Control] checkbox and setting the Serial Communication Mode to [Unicast]

(via an MY16-ES64).

• The AVS-ESMonitor application cannot be used while a ring network is in operation. In order to use the

AVS-ESMonitor application to control the head ampliﬁers it is necessary to either switch to a daisy

chain conﬁguration or add an EtherSound device with a third-port to the system.

• The on-screen head ampliﬁer controls can be operated both by click-and-drag and via the mouse scroll

wheel.

• Sound output may be brieﬂy interrupted when adjusting gain, but this is normal. Since the gain is being

internally adjusted in 6-dB steps, output is brieﬂy muted to prevent noise.

• The following parameters are not supported and cannot be edited even if shown on the display:

Device Mode/Name, Word Clock Source, Gain trim, Panel Lock, LED Brightness

Head Ampliﬁer Parameters That Can be Monitored and Controlled

Parameter Description

+48V Turns +48V phantom power ON or OFF for each channel.

HA GAIN Adjusts gain from -62 dB to +10 dB in 1-dB increments.

HPF Turns the high-pass ﬁlter ON or OFF.

HPF FREQ

Adjusts the cutoff frequency of the high-pass ﬁlter (12 dB/Oct.) from 20 Hz to 600 Hz

in 60 steps.

METER Displays a level meter for each input channel.

Device ID

Displays the automatically assigned device ID numbers 1–8 (corresponding to

AD8HR device ID numbers). Two ID numbers are assigned to each SB168-ES unit.

+48V Master SW Displays the master ON/OFF status of the +48V phantom power supply.

NOTE

SB168-ES Owner’s Manual

Troubleshooting

Symptom Possible Solution

The power won’t turn on. The power indicator

doesn’t light.

• Is the power cable connected properly? (page 6)

• Is the [POWER] switch properly engaged? (page 7)

• If you’ve checked all possible causes and the power still won’t come on, refer the

problem to your Yamaha dealer.

The unit is not receiving an input signal. • Are the input cables properly connected?

• Are the source devices delivering an appropriate signal? Check the SIG indicators

on the appropriate channels.

•Have you executed the Quick Setup function? Did you change any patch settings via

the AVS-ESMonitor application after executing the Quick Setup function?

• Are the AVS-ESMonitor patch settings appropriate (Net Patch or I/O Patch page)?

• Is the head ampliﬁer gain set to an appropriate level?

The input level is too low. • If a condenser microphone is being used, is the [+48V MASTER] switch ON?

• If a condenser microphone is being used, is phantom power for the corresponding

channel(s) turned ON?

• Is the head ampliﬁer gain set to an appropriate level?

No output. • Are the output cables properly connected?

•Have you executed the Quick Setup function? Did you change any patch settings via

the AVS-ESMonitor application after executing the Quick Setup function?

• Are the AVS-ESMonitor patch settings appropriate (Net Patch or I/O Patch page)?

• Is output muted at the digital mixing console?

An error message is displayed during Quick

Setup.

• Refer to page 17 for information on error messages that might be displayed during

execution of the AVS-ESMonitor Quick Setup function.

Head ampliﬁer remote control isn’t working. • Did you make the appropriate Head Amp Controller setting when executing the

Quick Setup function? Did you change the Serial Communication Mode setting after

executing the Quick Setup function?

• Is the AVS-ESMonitor Serial Communication Mode set properly? (page 16)

• If you will be controlling the head ampliﬁers via the 9-pin D-sub REMOTE connector

on a digital mixing console, is the mixing console’s REMOTE connector properly

connected to the HA REMOTE connector on the MY16-ES64 card (Primary Mas-

ter)? (page 14)

• If you will be controlling the head ampliﬁers via a mixing console expansion slot, is

the EXTERNAL HA display COMM PORT parameter set appropriately? (page 14)

• Set up the digital mixing console input patching in sequential 8-channel groups for

the slot inputs (CH1–8, CH9–16, etc.). This makes it easy to select input channels

on the external SB168-ES units for remote head ampliﬁer control.

Can’t control the SB168-ES by the M7CL-

48ES.

• Is the Stage Box Setup function of the M7CL-48ES set properly?

• Did you correctly set the DIP switches before turning on the power to the devices?

• Has the ﬁrmware been updated to an appropriate version?

• Can’t execute Quick Setup in the AVS-

ESMonitor

• Can’t change Serial Communication Mode

in the AVS-ESMonitor

• Is the AUTO CONFIGURE button for the Stage Box Setup function turned off?

• Are DIP switches 5–8 for the SB168-ES set to OFF (upper position)?

La pagina sta caricando ...

Yamaha ES Manuale del proprietario

Marca: Yamaha

Modello: ES

Categoria: Strumenti musicali

Tipo: Manuale del proprietario

Questo manuale è adatto anche per

SB168

Scarica il pdf

rapporto

in altre lingue

English: Yamaha ES Owner's manual
français: Yamaha ES Le manuel du propriétaire
español: Yamaha ES El manual del propietario
Deutsch: Yamaha ES Bedienungsanleitung
русский: Yamaha ES Инструкция по применению
Nederlands: Yamaha ES de handleiding
português: Yamaha ES Manual do proprietário
dansk: Yamaha ES Brugervejledning
čeština: Yamaha ES Návod k obsluze
polski: Yamaha ES Instrukcja obsługi
svenska: Yamaha ES Bruksanvisning
Türkçe: Yamaha ES El kitabı
suomi: Yamaha ES Omistajan opas
română: Yamaha ES Manualul proprietarului

Yamaha ES Manuale del proprietario

Questo manuale è adatto anche per

Yamaha ES Manuale del proprietario

in altre lingue

Documenti correlati