Axis Q1921 Guida d'installazione
- Categoria
- Accessori per telecamere di sicurezza
- Tipo
- Guida d'installazione
Legal Considerations
Video and audio surveillance can be prohibited by laws
that vary from country to country. Check the laws in
your local region before using this product for
surveillance purposes.
Trademark Acknowledgments
Apple, Boa, Bonjour, Ethernet, Internet Explorer, Linux,
Microsoft, Mozilla, Netscape Navigator, OS/2, Real,
SMPTE, QuickTime, UNIX, Windows, WWW are
registered trademarks of the respective holders. Java
and all Java-based trademarks and logos are trademarks
or registered trademarks of Sun Microsystems, Inc. in
the United States and other countries. Axis
Communications AB is independent of Sun
Microsystems Inc. UPnP™ is a certification mark of the
UPnP™ Implementers Corporation.
Electromagnetic Compatibility (EMC)
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures: Re-orient or relocate
the receiving antenna. Increase the separation between
the equipment and receiver. Connect the equipment to
an outlet on a different circuit to the receiver. Consult
your dealer or an experienced radio/TV technician for
help. Shielded (STP) network cables must be used with
this unit to ensure compliance with EMC standards.
USA - This equipment has been tested and found to
comply with the limits for a Class B computing device
pursuant to Subpart B of Part 15 of FCC rules, which are
designed to provide reasonable protection against such
interference when operated in a commercial
environment. Operation of this equipment in a
residential area is likely to cause interference, in which
case the user at his/her own expense will be required to
take whatever measures may be required to correct the
interference.
Canada - This Class B digital apparatus complies with
Canadian ICES-003
Europe - This digital equipment fulfills the requirements
for radiated emission according to limit B of EN55022,
and the requirements for immunity according to
EN55024 residential and commercial industry.
Japan - This is a class B product based on the standard
of the Voluntary Control Council for Interference from
Information Technology Equipment (VCCI). If this is used
near a radio or television receiver in a domestic
environment, it may cause radio interference. Install and
use the equipment according to the instruction manual.
Australia - This electronic device meets the
requirements of the Radio communications
(Electromagnetic Compatibility) Standard AS/NZS
CISPR22:2002.
Korea - Class B: As this equipment has obtained EMC
registration for household use, it can be used in any area
including residential areas.
Safety
Complies to EN 60950-1 (IEC 60950-1), Safety of
Information Technology Equipment.
Equipment Modifications
This equipment must be installed and used in strict
accordance with the instructions given in the user
documentation. This equipment contains no
user-serviceable components. Unauthorized equipment
changes or modifications will invalidate all applicable
regulatory certifications and approvals.
Liability
Every care has been taken in the preparation of this
document. Please inform your local Axis office of any
inaccuracies or omissions. Axis Communications AB
cannot be held responsible for any technical or
typographical errors and reserves the right to make
changes to the product and documentation without
prior notice. Axis Communications AB makes no
warranty of any kind with regard to the material
contained within this document, including, but not
limited to, the implied warranties of merchantability
and fitness for a particular purpose. Axis
Communications AB shall not be liable nor responsible
for incidental or consequential damages in connection
with the furnishing, performance or use of this material.
RoHS
This product complies with both the European
RoHS directive, 2002/95/EC, and the Chinese
RoHS regulations, ACPEIP.
WEEE Directive
The European Union has enacted a Directive
2002/96/EC on Waste Electrical and Electronic
Equipment (WEEE Directive). This directive is
applicable in the European Union member
states.
The WEEE marking on this product (see right) or its
documentation indicates that the product must not be
disposed of together with household waste. To prevent
possible harm to human health and/or the environment,
the product must be disposed of in an approved and
environmentally safe recycling process. For further
information on how to dispose of this product correctly,
contact the product supplier, or the local authority
responsible for waste disposal in your area.
Business users should contact the product supplier for
information on how to dispose of this product correctly.
This product should not be mixed with other commercial
waste.
ENGLISH
Safeguards
Please read through this Installation Guide carefully before installing the product. Keep the Installation Guide
for further reference.
CAUTION!
• When transporting the Axis product, use the original packaging or equivalent to prevent damage to the
product.
• Store the Axis product in a dry and ventilated environment. Keep the storage and operating temperature
within the limits stated in the User’s Manual available on the CD included in this package, or from
www.axis.com).
• Avoid exposing the Axis product to vibration, shocks or heavy pressure and do not install the camera on
unstable brackets, unstable or vibrating surfaces or walls, since this could cause damage to the product.
• Only use handtools when installing the Axis product, the use of electrical tools or excessive force could
cause damage to the product.
• Do not use chemicals, caustic agents, or aerosol cleaners. Use a damp cloth for cleaning.
• Only use accessories and spare parts provided or recommended by Axis.
• Do not attempt to repair the product by yourself, contact Axis or your Axis reseller for service matters.
IMPORTANT!
• This Axis product must be used in compliance with local laws and regulations.
• To use AXIS Q1921 outdoors, it must be installed in an approved outdoor housing.
• Do not install the camera near heat sources since fluctuating temperatures may affect image quality.
• The camera should be installed by a trained professional. Please observe relevant national and local regula-
tions for the installation.
Axis Thermal Camera Accessories and Spare Parts Installation Guide Page 5
ENGLISH
Axis Thermal Camera
Accessories and Spare Parts
Installation Guide
This Installation Guide provides instructions for installing and replacing accessories and spare parts
for AXIS Q1921/-E, including AXIS T92E23/T92E24 Thermal Camera Housing
To install the camera on the network, please see the Installation Guide provided with the camera.
For other details about the camera, see the User’s Manual, available from www.axis.com
Installation steps
1. Check the package contents against the list below.
2. Hardware overview. See page 6.
3a. Replace the lens. See page 8.
3b. Install the housing. See page 10.
3c. Replace the protective window. See page 13.
Package contents
The package contents vary depending on accessories and spare parts.
Item Models/variants/notes
Lens 10 mm/19 mm/35 mm/60 mm
Housing AXIS T92E23/T92E24 Thermal Camera Housing
Wall bracket
Outdoor network cable 5 m (16 ft.) with gasket
M20 Cable gland (for IP66)
Torx T20 screwdriver
Allen key
Camera screw and washer
Front kit Front panel
Frame with premounted protective window and window heater cable
Front panel screw (4x)
Printed materials Axis Thermal Camera Accessories and Spare Parts Installation Guide (this document)
Drill template
Axis Warranty document
Page 6 Axis Thermal Camera Accessories and Spare Parts Installation Guide
Hardware overview
Protective window
Front panel screw (4)
Front panel
Sunshield
Gasket
Frame
Window heater cable
Top cover
Network cable (route
Wall bracket
Bracket adjustment
through wall bracket)
Gasket
Bracket adapter
Bracket adapter
Thermal Camera Housing
Front kit
screw (4x)
screw
Page 8 Axis Thermal Camera Accessories and Spare Parts Installation Guide
Replace the lens
The instructions below describe how to replace the camera lens. For information on available lens
options, go to www.axis.com or contact your Axis reseller.
Outdoor cameras
1. Remove the top cover.
2. Disconnect the window heater cable from the window heater connector on the camera.
3. Refer to the instructions in Indoor/outdoor cameras, below.
Indoor/outdoor cameras
1. Disconnect the network cable.
2. Loosen the stop screw.
3. Unscrew the lens by turning it counter-clockwise.
Note: Make sure the wave bracket behind the lens stays in place.
4. Install the replacement lens by turning it clockwise.
5. Connect the network cable.
6. Open the Live View page of the network camera and go to Setup > System Options >
Advanced > Plain config.
7. Select ImageSource in the drop-down list and click Select group.
8. Select the matching lens option in the ImageSource IO Lens drop-down list.
9. Focus the camera to the appropriate distance. See the table below for recommended focus
distances for achieving optimal focus both for near focus and infinity.
10. Secure the stop screw.
Notes:
• Hold the lens gently by the metal ring; do not touch the lens surface.
• Be careful not to get dust on the sensor while exchanging the lens.
Lens 10 mm 19 mm 35 mm 60 mm
Focus distance 2 m (6.6 ft.) 8 m (26.2 ft.) 22 m (72.2 ft.) 60 m (196.9 ft.)
Wave bracket
Stop screw
Axis Thermal Camera Accessories and Spare Parts Installation Guide Page 9
ENGLISH
Adjust the holder distance
1. Loosen the upper holder screws.
2. Adjust the distance between the upper and lower holder according to the table below.
Note: Measure the holder distance on both sides of the camera to make sure the camera and
holders are mounted parallel to each other.
3. Tighten the screws.
Lens 10 mm 19 mm
Holder
distance
Lens 35 mm 60 mm
Holder
distance
9 mm
9 mm
10 mm
10 mm
0-2 mm
0-2 mm
17 mm
17 mm
Page 10 Axis Thermal Camera Accessories and Spare Parts Installation Guide
Install the housing
The instructions below describe how to install an indoor thermal network camera in a housing, see
www.axis.com for information on outdoor housings and other accessories.
Prepare the network cable
The provided network cable can be connected in several ways. The first option is to use the cable as
is, with the pre-mounted rubber gasket.
The second option is to use the provided plastic M20 cable gland, which must be used to achieve an
IP66 rating. Using any other cable gland may cause water to seep in and damage the camera.
If a cable other than the provided cable is used, you need to prepare a network cable with a gasket.
Gently force the cable through the gasket provided and attach a network connector. It may be
necessary to pierce a hole in the gasket with the supplied screwdriver.
Notes:
• Always use a shielded network cable (STP) between the camera and the end point and ensure that
the end point is properly grounded. Installations of Axis cameras using a shielded network cable (STP)
and a properly grounded end point have been tested to comply with industry immunity standards’
levels such as surge protection. Any other installation method will void the warranty and leave the
unit at a risk.
• Do not force the network connector into the gasket.
• Do not pierce the gasket with a knife or other sharp object.
Axis Thermal Camera Accessories and Spare Parts Installation Guide Page 11
ENGLISH
Install the camera in the housing
1. Remove the upper holder, see illustration on page 7.
2. Secure the camera and upper holder with the camera screw and washer.
3. Fit the upper holder on the lower holder and adjust the distance between holders according to
the table in Adjust the holder distance, on page 9.
4. Tighten the screws to 2 Nm. Be careful not to overtighten the screws.
5. Connect the window heater cable to the window heater connector on the camera, see
illustrations on page 6 and page 7.
6. Optionally insert an SD memory card (not included) into the SDHC (Secure Digital High
Capacity) card slot. A standard or high capacity SD card is required to store images locally in
the camera.
Install the wall bracket
1. Use the supplied drill template to prepare a wall for installation of the wall bracket.
2. Route the network cable through the wall bracket according to the wall bracket illustration on
page 6. Leave approximately 30 cm (11.8”) of cable for connecting the camera.
3. Install the wall bracket on a wall and make sure that the screws and plugs are appropriate for
the material (e.g. wood, metal, sheet rock, stone).
Install the camera on the bracket
1. Loosen the cable cover screws and remove the cable cover from the bottom cover.
2. Install the camera with the bottom cover on the bracket and tighten the bracket adapter
screws.
3. Remove the gasket from one of the cable holes in the bottom cover.
4. Route the cable through the hole and attach the cable gasket to the hole.
Cable cover
Cable cover screw (2x)
Network cable (route
through wall bracket)
Cable holes with gaskets
Bottom cover
Wall bracket
Bracket screw (4x)
Bracket adjustment screw
Page 12 Axis Thermal Camera Accessories and Spare Parts Installation Guide
5. Install the cable cover and tighten the cable cover screws.
6. Connect the camera to the network using a shielded network cable.
7. Loosen the bracket adjustment screw to aim the camera to the point of interest and focus the
camera, see the Installation Guide provided with the camera for information on how to access
the video stream. If the lens has been changed, the camera’s image source has to be updated,
see Indoor/outdoor cameras, on page 8.
8. Take the top cover and attach the safety wire to the tab on the bottom cover.
9. Install the top cover. Make sure to tighten diagonally opposite bottom cover screws a few turns
at a time until all are tight. This will help ensure that the bottom cover gasket is compressed
evenly.
10. Loosen the sunshield adjustment screws and adjust the sunshield to the desired position.
Axis Thermal Camera Accessories and Spare Parts Installation Guide Page 13
ENGLISH
Replace the protective window
The instructions below describe how to replace the protective window. Use the appropriate size of
front kit for the lens.
1. Remove the top cover.
2. Disconnect the window heater cable from the window heater connector on the camera.
3. Loosen the 4 front panel screws and remove the front panel and the frame.
4. Replace the gasket.
5. Carefully attach the replacement frame to the housing so that the window heater connector is
in the lower right corner, see front panel illustration on page 6.
Note: Do not touch the window, only touch the frame.
6. Install the front panel.
Note: Use the provided large front panel and the longer screws when installing the large protective
window.
7. Connect the window heater cable to the window heater connector on the camera, see
illustration on page 7.
8. Take the top cover and attach the safety wire to the tab on the bottom cover.
9. Install the top cover. Make sure to tighten diagonally opposite bottom cover screws a few turns
at a time until all are tight. This will help ensure that the bottom cover gasket is compressed
evenly.
10. Loosen the sunshield adjustment screws and adjust the sunshield to the desired position.
Lens Front kit, including front panel and frame with premounted protective window
10 mm Medium (38 mm germanium window)
19 mm Medium (38 mm germanium window)
35 mm Medium (38 mm germanium window)
60 mm Large (64 mm germanium window)
Protective window
Front panel screw (4)
Front panel
Frame
(premounted)
Gasket
Page 14 Axis Thermal Camera Accessories and Spare Parts Installation Guide
Further information
See the Installation Guide for information on how assign an IP address, set the password and access
the video stream. The Installation Guide is provided with the camera and is available from the Axis
Web site at www.axis.com
Mesures de sécurité
Lisez attentivement le présent guide d’installation avant d’installer le produit. Conservez le guide d’installation
si vous souhaitez le consulter ultérieurement.
ATTENTION !
• Pour éviter d’endommager le produit Axis, utilisez l’emballage d’origine ou un équivalent pour le
transporter.
• Stockez le produit Axis dans un environnement sec et aéré. Gardez les températures de stockage et
d’utilisation dans les limites spécifiées dans le manuel de l'utilisateur disponible sur le CD inclus ou sur
www.axis.com).
• Évitez d’exposer le produit Axis à des vibrations, des chocs ou une trop forte pression et ne l’installez pas
sur des supports instables, ou des surfaces ou des murs instables ou vibrants. Cela risque de l’endommager.
• Utilisez uniquement des outils manuels pour l’installation du produit Axis, l’utilisation d’outils électriques
ou l’usage excessif de la force risque de l’endommager.
• N’utilisez ni produits chimiques, ni substances caustiques, ni nettoyeurs aérosol. Utilisez un linge humide
pour le nettoyage.
• Utilisez uniquement des accessoires et des pièces de rechange fournis ou recommandés par Axis.
• Ne tentez pas de réparer le produit vous-même, contactez Axis ou votre revendeur Axis pour tout problème
lié au service.
IMPORTANT !
• Ce produit Axis doit être utilisé conformément aux lois et réglementations locales en vigueur.
• Pour pouvoir utiliser AXIS Q1921 à l’extérieur, elle doit être placée dans un boîtier d’extérieur homologué.
• N’installez pas la caméra à proximité de sources de chaleur puisque les variations de température peuvent
nuire à la qualité de l’image.
• La caméra doit être installée par un professionnel qualifié. Respectez les réglementations nationales et
locales concernant l’installation.
Accessoires et pièces de rechange pour caméra thermique Axis Guide d’installation Page 17
FRANÇAIS
Caméra thermique Axis
Accessoires et pièces de rechange
Guide d’installation
Ce guide d’installation contient les instructions relatives à l’installation et au remplacement des
accessoires et pièces de rechange de AXIS Q1921/-E, et notamment Boîtier de caméra thermique AXIS
T92E23/T92E24
Pour installer la caméra sur le réseau, veuillez vous référer au guide d’installation fourni avec la
caméra. Pour obtenir de plus amples détails relatifs à la caméra, consultez le manuel de l’utilisateur,
disponible sur le site www.axis.com
Procédure d’installation
1. Vérifiez que l’emballage contient bien tous les éléments répertoriés dans la liste ci-dessous.
2. Vue d’ensemble du matériel. Reportez-vous à la page 18.
3a. Remplacer l’objectif. Reportez-vous à la page 20.
3b. Installer le boîtier. Reportez-vous à la page 23.
3c. Remplacer la fenêtre de protection. Reportez-vous à la page 26.
Contenu de l’emballage
Le contenu de l’emballage varie en fonction des accessoires et des pièces de rechange.
Élément Modèles/variantes/remarques
Objectif 10 mm/19 mm/35 mm/60 mm
Boîtier Boîtier de caméra thermique AXIS T92E23/T92E24
Support mural
Câble réseau d’extérieur 5 m avec joint
Presse-étoupe M20 (pour IP66)
Tournevis TorxT20
Clé hexagonale
Vis et rondelle de la caméra
Kit avant Panneau avant
Cadre équipé d’une fenêtre de protection préalablement montée et d’un câble de
régulateur de chaleur
Vis du panneau avant (4)
Documentation
imprimée
Guide d’installation Accessoires et pièces de rechange pour caméra thermique Axis (le
présent document)
Gabarit de perçage
Document de garantie d’Axis
Page 18 Accessoires et pièces de rechange pour caméra thermique Axis Guide d’installation
Vue d’ensemble du matériel
Fenêtre de protection
Vis du panneau avant (4)
Panneau avant
Pare-soleil
Joint
Cadre
Câble du régulateur de chaleur
Couvercle supérieur
Câble réseau (acheminement
Support mural
Vis de réglage
à travers le support mural)
Joint
Adaptateur de support
Vis de l’adaptateur
Boîtier de caméra thermique
Kit avant
de support (4)
du support
Accessoires et pièces de rechange pour caméra thermique Axis Guide d’installation Page 19
FRANÇAIS
Vis du support supérieur (2)
Vis et rondelle de la caméra
Support supérieur
Couvercle inférieur
Connecteur du
régulateur de chaleur
Support inférieur
Vis de butée
Montage de la caméra
Vis du support
Trou de câble avec
joint
Couvercle de câble
inférieur (2)
Page 20 Accessoires et pièces de rechange pour caméra thermique Axis Guide d’installation
Remplacer l’objectif
Les instructions ci-après expliquent le remplacement de l’objectif de la caméra. Pour obtenir de plus
amples informations concernant les options d’objectif disponibles, consultez le site www.axis.com ou
contactez votre revendeur Axis.
Caméras extérieures
1. Retirez le couvercle supérieur.
2. Déconnectez le câble du régulateur de chaleur au niveau du connecteur du régulateur de
chaleur sur la caméra thermique.
3. Reportez-vous aux instructions de la sectionCaméras pour l’intérieur/l’extérieur ci-après.
Caméras pour l’intérieur/l’extérieur
1. Débranchez le câble réseau.
2. Dévissez la vis de
butée.
3. Dévissez l’objectif en tournant ce dernier dans le sens inverse des aiguilles d’une montre.
Remarque: Assurez-vous que le joint qui se trouve à l’arrière de l’objectif reste en place.
4. Fixez l’objectif de rechange en le tournant dans le sens des aiguilles d’une montre.
5. Branchez le câble réseau.
6. Ouvrez la page LiveView de la caméra réseau et accédez à Setup (Configuration) > System
Options (Options système) > Advance (Avancé) > Plain config (Configuration simple).
7. Sélectionnez ImageSource dans la liste locale, puis cliquez sur Select group (Sélectionner le
groupe).
8. Dans la liste locale ImageSource IO Lens (Objectif ImageSource E/S), sélectionnez l’option
d’objectif correspondante.
9. Procédez à la mise au point de la caméra à la distance requise. Consultez le tableau ci-après
pour les distances de mise au point recommandées, afin d’obtenir la mise au point optimale
autant pour la mise au point approximative que pour la mise au point fixe.
Objectif 10 mm 19 mm 35 mm 60 mm
Distance de mise au point 2 m (6,6pi) 8 m (26,2pi) 22 m (72,2pi) 60 m (196,9pi)
Joint
Vis de butée
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
Axis Q1921 Guida d'installazione
- Categoria
- Accessori per telecamere di sicurezza
- Tipo
- Guida d'installazione
in altre lingue
- English: Axis Q1921 Installation guide
- français: Axis Q1921 Guide d'installation
- español: Axis Q1921 Guía de instalación
- Deutsch: Axis Q1921 Installationsanleitung