PSI Matrix PP 407 Manuale utente

PSi Matrix GmbH Freudenberg

User Manual

PP 407 / PP 408

User Manual PP 407 / PP 408

Uwe Panthel - PSi Customer Support

.

A Publication of Psi Matrix GmbH

Hommeswiese 116

57258 Freudenberg, Germany

hp://www.psi-matrix.eu

Great care has been taken to ensure that the informaon in this handbook is accurate and

complete. However, should any errors or omissions be discovered or should any user wish to make

suggesons for improving this handbook, please feel encouraged to send us the relevant details.

GmbH.

All rights strictly reserved. Reproducon or issue to third pares in any form is not permied

without wrien authorizaon from the publisher.

Acknowledgements

EPSON is a Trademark of Seiko Epson Corporaon.

IBM is a Trademark of Internaonal Business Machines Corporaon.

ProPrinter is a Trademark of

internaonal Business Machines Corporaon.

Safety Regulaons

The printers PP 407 (High Speed Fanfold Printer) and the

PP 408 (High Speed Fanfold Printer with Cuer) fulls the safety regulaons according to EN 60950-

1, UL 60950-1 and CAN/CSA 22.2/No. 60950-1 for Informaon Technology Equipment.

The mains cable must be connected to a ground protected wall-socket. The indicated voltage of the

printer needs to agree with the local voltage.

The power plug must be easily accessible at any me so that it can be disconnected immediately in

case of danger or for maintenance purposes.. Comme le câble de secteur sert de diposif d‘arrêt-

urgence, sa connexion à l‘imprimante doit être tout le temps accessible.

Before installing the printer, check the surrounding condions in which the printer will be placed

(see next page, Operang Environment and chapter 2).

During a thunderstorm you should never aempt to connect or disconnect any data transfer cables.

The power supply should only be opened and checked by authorized personnel. Repairs and

maintenance beyond the descripons of chapter 7 Maintenance may only be aempted by

authorized personnel as well. Repairs deine inappropriately may cause damage and severe danger

for the user.

There are warning symbols to draw the user‘s aenon to possible injuries:

This symbol is visible when the top cover has been opened. It indicates that the print

head is extremely hot aer leing periods of prinng.

Electromagnec Compability

We cerfy that the equipment at issue,

• Printer PP 407 (High Speed Fanfold Printer) and

• Printer PP 408 (High Speed Fanfold Printer with Cuer)

corresponds to the law regulaons ruling electromagnec compability of

appliances (2004/108/EC)

and, therefore, fulls the requirements for conformity marking with the CE-sign.

To assure the compliance with the liming values in according to the test

standards for interference

(EN 55022, class B) and noise immunity (EN 55024), shielded interface cables must be used.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protecon

against harmful interference in a residenal installaon. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the instrucon

manual, may cause interference to radio communicaons.

However, there is no guarantee that interference will not occur in a parcular installaon. If this

equipment does cause harmful interference to radio or television recepon, it can be determined by

turning the equipment o and on. The user is encouraged to try to correct the interference by eine

or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separaon between the equipment and receiver.

• Connect the equipment to an outlet on a circuit dierent from the circuit to

which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Shielded interface cables should be used with this unit to ensure compliance with Class B limits.

Changes and modicaons not explicitly allowed by the equipment‘s manufacturer could void the

user‘s authority to operate the equipment.

Changes et modicaons pas expressément approuvés par le producteur peuvent dévaluer

l‘autorité d‘opérer l‘équipement.

6

Operang Environment

Avoid installing the printer where it is exposed to moisture or heat (eg. direct sun light).

• Temperature: + 10°C to + 35°C (+50°F to +95°F)

• Humidity: 20% to 80%

Slots and openings in the printer‘s housing are provided for venlaon. Always ensure that these

openings are not obstructed.

Also ensure that the cables at the rear of the printer do not interfere with the output paper path.

Chapter 1-1

1. Preface

About this Manual

This manual is covering the two printers

• High Speed Fanfold Printer

• High Speed Fanfold Printer with Cuer

The operaon and funconality are nearly the same. In most illustraons, the High Speed Fanfold Printer

with Cuer is used. In case there are dierences in the handling you will nd the note:

• High Speed Fanfold Printer

or

• High Speed Fanfold Printer with Cuer

The Interface (Personality Module (PM)) is an integral part of the printer, and the type of PM used,

determines the funconality of the printer especially regarding the user and system interface.

The manual is divided into the following chapters:

1. Preface

About the manual

2. 

This chapter explains how to unpack and set up the printer and how to install the personality







has not yet taken place.

3. Operang the Printer

This chapter discusses in detail the operaon of the operator panel, all menu funcons, and

the general operaon of the menu.

4. Maintenance

Shows how to clean the printer and how to replace the platen and the print head.

5. Trouble Shoong and Diagnoscs

Suggests how to idenfy and correct simple problems.

6. Technical Data

All technical details or data about the printer can be found here.

Chapter 1-2

Appendix

A Interface Descripon

This chapter gives hints about possibilies to connect the printer to the various computer

systems and explains parcularies depending on the version of the operang system.

Addionally, cable connecon is illustrated

B Print examples of the standard fonts

C Character Set Tables

All printer supported character sets are listed in this chapter

D / E Control Codes

• IBM ProPrinter and IBM ProPrinter AGM (4207, 4208 XL24) Emulaon.

• EPSOM LQ 2550 / ESC/P2 Emulaon

F Barcode Reference

Chapter 1-3



The following convenons are used:

Bold Headlines and important informaon.

Note: Contains special advice to facilitate handling.

 Contains important informaon to prevent damage of the equipment.

Aenon: Informaon that requires special aenon

[ENTER] Key funcons are always depicted in brackets or you will nd the symbol of the key

e.g



AGC AAutomac Gap Control

EE Eastern European

LCD Liquid Crystal Display

LED Light Eming Diode

DK PrintHead

MACRO User dened groups (1 - 4) of printer parameters

PM Interface (Personality Module), Serial, USB and Parallel

LQ Leer Quality

NLQ Near Leer Quality

DQ Dra Quality

The operaon of both printers is almost idencal. Most of the illustraons show the PP 408 printer.

Dierences in handling have special references to the printer PP 407 or PP 408.

Chapter 2-1



2.1 Unpacking High Speed Fanfold Printer (Content PP407)

Check each item against the check list detailed below. Contact your reseller immediately if any

item is missing or damaged.

The printer package should contain the following parts:

• 24-Needle Printer (1)

• Ribbon cassee (2)

• Powercord (3)

• Quick Reference Guide (4)

• Interface PM (must be ordered separatly)

• Produkt CD with documentaon, drivers ect. (6)

An interface module (5), also called “Personality Module” or briey “PM”, is in a separate packing

and must be ordered separatly.

Note: All packaging materials should be for future transport of the printer be kept.

• Do not connect to the mains unl the main‘s voltage seng has been checked

• The transport lock has been removed and the PM is installed.

• The printer drivers for Windows ® are available on the enclosed CD-ROM.

Chapter 2-2

2.1.1 A First Look at the High Speed Fanfold Printer

Before installing the printer, spend some me familiarizing yourself with the printer.

Top cover (1) Power cord socket (6)

Ribbon cassee (2) Control panel (7)

Printer base (3) Interface serial, parallel, USB (8)

Tractor cassees (4) Tear o edge (9)

Power switch(5) Cable clip(10)

Chapter 2-3

2.2 Unpacking High Speed Fanfold Printer with cuer (Content PP408)

Check each item against the check list detailed below. Contact your reseller immediately if any

item is missing or damaged.

The printer package should contain the following parts:

• 24-Needle Printer (1)

• Ribbon cassee (2)

• Powercord (3)

• Quick Reference Guide (4)

• Interface PM (must be ordered separatly)

• Produkt CD with documentaon, drivers ect. (6)

• Cung device (7)

An interface module (5), also called “Personality Module” or briey “PM”, is in a separate packing

and must be ordered separatly.

Note: All packaging materials should be for future transport of the printer be kept.

• Do not connect to the mains unl the main‘s voltage seng has been checked

• The transport lock has been removed and the PM is installed.

• The printer drivers for Windows ® are available on the enclosed CD-ROM.

Chapter 2-4

2.2.1 A First Look at the High Speed Fanfold Printer with cuer (PP 408)

Before installing the printer, spend some me familiarizing yourself with the printer..

Top cover(1) Operator panel (7)

Cung device (2) Interface serial, parallel, USB (8)

Printer base (3) Tear o edge (9)

Ribbon cassee (4) Cable clip (10)

Tractor cassees (5) Power cord socket (11)

Power switch (6)

Chapter 2-5

2.3 Site Consideraons



• Install the printer in an area away from any heat source, air condieiner or streing draught.

• Avoid installing the printer in a dusty or humid environment.



• Place the printer on the stand or a at, solid level area such as a desk.

• Slots and openings in the printer‘s housing are provided for venlaon; always ensure that

these openings are not obstructed.

• Always place the printer with its front edge slightly o the edge of the table when processing

fanfold paper.

• Also ensure that the cables at the rear of the printer do not interfere with the output paper

path.

Power Requirements

• No special wiring is required. A typical oce wall outlet is sucient.

• Do not plug in other equipment besides the printer such as coee machines, copy machines or

air condieiners into the same wall outlet.

Chapter 2-6

2.4 Mounng the Cung Device (only for High Speed Fanfold Printer with Cuer)

• Insert the pins (3) of the Cung Device (2) into the mounng plate (4).

• Swivel the Cung Device (2) to the Printer (1) and push the support plates (5) onto the pins (6).

• Push in the plug (8) into the socket (9)

• Press the Cung Device (2) toward to the printer so, that the retainers (7) lock visible and with

an audible click.

• Insert the top cover.

3

1

2

4

3

1

2

7

5

8

9

Chapter 2-7

2.5 Transport Lock

In delivery condion a red shipping tab is visible under the top cover (1), which is aached with the

transport locking clip (2).

Li up the top cover (1) and remove the transport locking clip (2) from the print head drive belt.

• Carefully remove the red warning strip and the transport securing clip (2) of the print headnen.

Repacking Informaon

Save all packing material and boxes for future transportaon of the printer. To ensure maximum

protecon when transporng the printer, please pay aenon to the following:

• Push the output stacker into the top cover and pack it separately.

• Remove the power cord.

• Remove the ribbon cassee.

• Reposion the transport locking clip.

• Dismantle the Cuer Unit and pack it separately.

• Pack the complete printer in its original packing box and ship it.

Pay aenon to the ‚Packing Note‘!

Chapter 2-8

2.6 Installaon of the interface (PM)

The printer funcons only in combinaon with an installed interface module, called a Personality

Module (PM). The illustraon below shows the standard PM with a serial, parallel, and USB interface.

Note: To avoid damage due to electrostac discharge, do not touch the pins or compeinents of the

PM. ) Never aempt to install or remove a PM while the printer is switched ON.

The Printer must be powered o! Remove the PM (1) from its packing material. Insert the Personality

Module (1) with the compeinent side upwards unl the connector fully engages. Hand ghten the

two lock screws (2)..

Info: The PM does not beleing to the standard sump of the printer. It must be ordered separately.

PSi provides dierent variants;

2

1

PM SER/PAR/USB PM SER/PAR/USB/ETH PM SER/USB/ETH

PM IGP PAR PM IGP ETH PM IPDS ETH

Chapter 2-9

2.7 Power supply and power on printer

Mains Voltage

In general, the main‘s voltage selecon is determined at factory sites.Make sure that the specied

voltage on the label (1) corresponds to your main‘s voltage:

The 230 V seng applies to the range of 180 to 264 V alternang current.

Note: Since an incorrect voltage selecon can seriously damage the printer, please pay special

aenon to the following.

Connect the printer to the mains using the power cord (2). First connect the cable to the power cord

socket and then to the mains. Fasten the Power cord depending upon posion of the mains, into

the clip (3) or (4).

Note: As the power cord serves as a safety cut o, its connecon to the printer must be accessible

any me.

230 VAC 115 VAC

oder

1

2

3

Chapter 2-10

Power ON/OFF

The power ON/OFF switch (1) turns the printer‘s power supply ON or OFF.

Aer switched ON the printer an internal self-test which checks the electronics, the print head

carriage movement and the interface will be performed.

At rst the yellow LED on the Operator Panel is lighng up and the display shows TEST.....0.1

(bootstrap). In the next step the yellow LED will be dark, the green LED lights up and the display

shows TEST....FW..0101234 (version of the rmware).

If the message INSTALL RIBBON is shown, the ribbon must be inserted as described on the

following pages or conrmed if already inserted.

Aer inserng the ribbon press dto connue. When the internal test has been completed

successfully the display showsREADY 1 ELQ or in case data has already been transmied.

BUSY 1 ELQ

.

Note: If the display shows anything dierent please refer to chapter 4 Troubleshoong

and Diagnoscs.

Chapter 2-11

2.8 Installing ribbon cassee

Hinweis: It is recommended to use only original ribbon puts out by our company. Using other

ribbons will void your warranty.

Cauon: Never manually move the print head fully to the right-hand stop (you could change

the way of the paper output).

1. Switch the printer ON at the power switch; Power LED is lit and waits for the message READY

1 ELQ or INSTALL RIBBON.

2. If the printer is busy (message BUSY 1 ELQ) press .

3. Put the ribbon cassee out of the box

4. Remove any excess slack by turning the green knob (1) on the ribbon cassee clockwise.

Move the ribbon feed guide (2) to the posion indicated on the plasc housing of the cassee.

5. Li the top cover (3) to gain access to the ribbon cassee mounngs. The print head will

move to the correct posion, aligned with the cut out in the paper guide plate to facilitate the

installaon of the ribbon cassee.

6. Feed the ribbon cassee down into the printer with the ribbon facing down.

7. Then place the upper assembly pins (9) of the cassee on both sides of the upper part of the

green ribbon holder. In this posion, the ribbon guide (10) contacts the green plasc clip (10)

1

2

Chapter 2-12

8. Then move the cassee towards you unl it clicks into place on both sides. Now swivel the

ribbon under the print head unl the lower retaining pins click (click!).

Note: At each end of the ribbon cassee there are two pins (9) and (10) which keep

the cassee in posion when mounted. When installed correctly the ribbon

cassee is

not parallel to the printer‘s housing (12).

1. Move the print head (4) back and forth to sele the ribbon in the correct posion.

2. If necessary remove excess ribbon slack by turning the green knob (6) clockwise.

3. Close the top cover (3) and press .

9

10

12

11

Click

La pagina sta caricando ...

PSI Matrix PP 407 Manuale utente

Questo manuale è adatto anche per

PSI Matrix PP 407 Manuale utente

in altre lingue

Altri documenti