Genius Linear Istruzioni per l'uso

Categoria
Gate Opener
Tipo
Istruzioni per l'uso
Linear
AVVERTENZE PER L’INSTALLATORE
OBBLIGHI GENERALI PER LA SICUREZZA
1) ATTENZIONE! È importante per la sicurezza delle persone seguire attenta-
mente tutta l’istruzione. Una errata installazione o un errato uso del prodotto
può portare a gravi danni alle persone.
2)
Leggere attentamente le istruzioni prima di iniziare l’installazione del prodot-
to.
3) I materiali dell’imballaggio (plastica, polistirolo, ecc.) non devono essere
lasciati alla portata dei bambini in quanto potenziali fonti di pericolo.
4) Conservare le istruzioni per riferimenti futuri.
5) Questo prodotto è stato progettato e costruito esclusivamente per l’utilizzo
indicato in questa documentazione. Qualsiasi altro utilizzo non espressamen-
te indicato potrebbe pregiudicare l’integrità del prodotto e/o rappresen-
tare fonte di pericolo.
6) GENIUS declina qualsiasi responsabilità derivata dall’uso improprio o diverso
da quello per cui l’automatismo è destinato.
7) Non installare l’apparecchio in atmosfera esplosiva: la presenza di gas o fumi
infiammabili costituisce un grave pericolo per la sicurezza.
8) Gli elementi costruttivi meccanici devono essere in accordo con quanto
stabilito dalle Norme EN 12604 e EN 12605.
Per i Paesi extra-CEE, oltre ai riferimenti normativi nazionali, per ottenere un
livello di sicurezza adeguato, devono essere seguite le Norme sopra riporta-
te.
9) GENIUS non è responsabile dell’inosservanza della Buona Tecnica nella co-
struzione delle chiusure da motorizzare, nonché delle deformazioni che
dovessero intervenire nell’utilizzo.
10) L’installazione deve essere effettuata nell’osservanza delle Norme EN 12453
e EN 12445. Il livello di sicurezza dell’automazione deve essere C+E.
11) Prima di effettuare qualsiasi intervento sull’impianto, togliere l’alimentazione
elettrica.
12) Prevedere sulla rete di alimentazione dell’automazione un interruttore
onnipolare con distanza d’apertura dei contatti uguale o superiore a 3 mm.
È consigliabile l’uso di un magnetotermico da 6A con interruzione onnipolare.
13) Verificare che a monte dell’impianto vi sia un interruttore differenziale con
soglia da 0,03 A.
14) Verificare che l’impianto di terra sia realizzato a regola d’arte e collegarvi
le parti metalliche della chiusura.
15) L’automazione dispone di una sicurezza intrinseca antischiacciamento co-
stituita da un controllo di coppia. E' comunque necessario verificarne la sogli
di intervento secondo quanto previsto dalle Norme indicate al punto 10.
16) I dispositivi di sicurezza (norma EN 12978) permettono di proteggere even-
tuali aree di pericolo da Rischi meccanici di movimento, come ad Es.
schiacciamento, convogliamento, cesoiamento.
17) Per ogni impianto è consigliato l’utilizzo di almeno una segnalazione lumino-
sa nonché di un cartello di segnalazione fissato adeguatamente sulla struttu-
ra dell’infisso, oltre ai dispositivi citati al punto “16”.
18) GENIUS declina ogni responsabilità ai fini della sicurezza e del buon funziona-
mento dell’automazione, in caso vengano utilizzati componenti dell’impian-
to non di produzione GENIUS.
19) Per la manutenzione utilizzare esclusivamente parti originali GENIUS.
20) Non eseguire alcuna modifica sui componenti facenti parte del sistema
d’automazione.
21) L’installatore deve fornire tutte le informazioni relative al funzionamento
manuale del sistema in caso di emergenza e consegnare all’Utente
utilizzatore dell’impianto il libretto d’avvertenze allegato al prodotto.
22) Non permettere ai bambini o persone di sostare nelle vicinanze del prodotto
durante il funzionamento.
23) Tenere fuori dalla portata dei bambini radiocomandi o qualsiasi altro datore
di impulso, per evitare che l’automazione possa essere azionata involonta-
riamente.
24) Il transito tra le ante deve avvenire solo a cancello completamente aperto.
25) L’Utente utilizzatore deve astenersi da qualsiasi tentativo di riparazione o
d’intervento diretto e rivolgersi solo a personale qualificato.
26) Tutto quello che non è previsto espressamente in queste istruzioni non è
permesso
CONSIGNES POUR L'INSTALLATEUR
RÈGLES DE SÉCURITÉ
1) ATTENTION! Il est important, pour la sécurité des personnes, de suivre à la
lettre toutes les instructions. Une installation erronée ou un usage erroné
du produit peut entraîner de graves conséquences pour les personnes.
2)
Lire attentivement les instructions avant d'installer le produit.
3) Les matériaux d'emballage (matière plastique, polystyrène, etc.) ne doivent
pas être laissés à la portée des enfants car ils constituent des sources
potentielles de danger.
4) Conserver les instructions pour les références futures.
5) Ce produit a été conçu et construit exclusivement pour l'usage indiqué dans
cette documentation. Toute autre utilisation non expressément indiquée
pourrait compromettre l'intégrité du produit et/ou représenter une source
de danger.
6) GENIUS décline toute responsabilité qui dériverait d'usage impropre ou
différent de celui auquel l'automatisme est destiné.
7) Ne pas installer l'appareil dans une atmosphère explosive: la présence de
gaz ou de fumées inflammables constitue un grave danger pour la sécurité.
8) Les composants mécaniques doivent répondre aux prescriptions des Normes
EN 12604 et EN 12605.
Pour les Pays extra-CEE, l'obtention d'un niveau de sécurité approprié exige
non seulement le respect des normes nationales, mais également le respect
des Normes susmentionnées.
9) GENIUS n'est pas responsable du non-respect de la Bonne Technique dans la
construction des fermetures à motoriser, ni des déformations qui pourraient
intervenir lors de l'utilisation.
10) L'installation doit être effectuée conformément aux Normes EN 12453 et EN
12445. Le niveau de sécurité de l'automatisme doit être C+E.
11) Couper l'alimentation électrique avant toute intervention sur l'installation.
12) Prévoir, sur le secteur d'alimentation de l'automatisme, un interrupteur
omnipolaire avec une distance d'ouverture des contacts égale ou supérieure
à 3 mm. On recommande d'utiliser un magnétothermique de 6A avec
interruption omnipolaire.
13) Vérifier qu'il y ait, en amont de l'installation, un interrupteur différentiel avec
un seuil de 0,03 A.
14) Vérifier que la mise à terre est réalisée selon les règles de l'art et y connecter
les pièces métalliques de la fermeture.
15) L'automatisme dispose d'une sécurité intrinsèque anti-écrasement, formée
d'un contrôle du couple. Il est toutefois nécessaire d'en vérifier le seuil
d'intervention suivant les prescriptions des Normes indiquées au point 10.
16) Les dispositifs de sécurité (norme EN 12978) permettent de protéger des
zones éventuellement dangereuses contre les Risques mécaniques du
mouvement, comme l'écrasement, l'acheminement, le cisaillement.
IMPORTANT NOTICE FOR THE INSTALLER
GENERAL SAFETY REGULATIONS
1) ATTENTION! To ensure the safety of people, it is important that you read
all the following instructions. Incorrect installation or incorrect use of the
product could cause serious harm to people.
2)
Carefully read the instructions before beginning to install the product.
3) Do not leave packing materials (plastic, polystyrene, etc.) within reach of
children as such materials are potential sources of danger.
4) Store these instructions for future reference.
5) This product was designed and built strictly for the use indicated in this
documentation. Any other use, not expressly indicated here, could compro-
mise the good condition/operation of the product and/or be a source of
danger.
6) GENIUS declines all liability caused by improper use or use other than that for
which the automated system was intended.
7) Do not install the equipment in an explosive atmosphere: the presence of
inflammable gas or fumes is a serious danger to safety.
8) The mechanical parts must conform to the provisions of Standards EN 12604
and EN 12605.
For non-EU countries, to obtain an adequate level of safety, the Standards
mentioned above must be observed, in addition to national legal regulations.
9) GENIUS is not responsible for failure to observe Good Technique in the
construction of the closing elements to be motorised, or for any deformation
that may occur during use.
10) The installation must conform to Standards EN 12453 and EN 12445. The safety
level of the automated system must be C+E.
11) Before attempting any job on the system, cut out electrical power.
12) The mains power supply of the automated system must be fitted with an all-
pole switch with contact opening distance of 3mm or greater. Use of a 6A
thermal breaker with all-pole circuit break is recommended.
13) Make sure that a differential switch with threshold of 0.03 A is fitted upstream
of the system.
14) Make sure that the earthing system is perfectly constructed, and connect
metal parts of the means of the closure to it.
15) The automated system is supplied with an intrinsic anti-crushing safety device
consisting of a torque control. Nevertheless, its tripping threshold must be
checked as specified in the Standards indicated at point 10.
16) The safety devices (EN 12978 standard) protect any danger areas against
mechanical movement Risks, such as crushing, dragging, and shearing.
17) Use of at least one indicator-light is recommended for every system, as well
as a warning sign adequately secured to the frame structure, in addition to
the devices mentioned at point “16”.
18) GENIUS declines all liability as concerns safety and efficient operation of the
automated system, if system components not produced by GENIUS are used.
19) For maintenance, strictly use original parts by GENIUS.
20) Do not in any way modify the components of the automated system.
21) The installer shall supply all information concerning manual operation of the
system in case of an emergency, and shall hand over to the user the warnings
handbook supplied with the product.
22) Do not allow children or adults to stay near the product while it is operating.
23) Keep remote controls or other pulse generators away from children, to
prevent the automated system from being activated involuntarily.
24) Transit through the leaves is allowed only when the gate is fully open.
25) The user must not attempt any kind of repair or direct action whatever and
contact qualified personnel only.
26) Anything not expressly specified in these instructions is not permitted.
ADVERTENCIAS PARA EL INSTALADOR
REGLAS GENERALES PARA LA SEGURIDAD
1) ¡ATENCION! Es sumamente importante para la seguridad de las personas
seguir atentamente las presentes instrucciones. Una instalación incorrecta
o un uso impropio del producto puede causar graves daños a las personas.
2)
Lean detenidamente las instrucciones antes de instalar el producto.
3) Los materiales del embalaje (plástico, poliestireno, etc.) no deben dejarse al
alcance de los niños, ya que constituyen fuentes potenciales de peligro.
4) Guarden las instrucciones para futuras consultas.
5) Este producto ha sido proyectado y fabricado exclusivamente para la
utilización indicada en el presente manual. Cualquier uso diverso del previ-
sto podría perjudicar el funcionamiento del producto y/o representar fuente
de peligro.
6) GENIUS declina cualquier responsabilidad derivada de un uso impropio o
diverso del previsto.
7) No instalen el aparato en atmósfera explosiva: la presencia de gas o humos
inflamables constituye un grave peligro para la seguridad.
8) Los elementos constructivos mecánicos deben estar de acuerdo con lo
establecido en las Normas EN 12604 y EN 12605.
Para los países no pertenecientes a la CEE, además de las referencias
normativas nacionales, para obtener un nivel de seguridad adecuado, deben
seguirse las Normas arriba indicadas.
9) GENIUS no es responsable del incumplimiento de las buenas técnicas de
fabricación de los cierres que se han de motorizar, así como de las
deformaciones que pudieran intervenir en la utilización.
10) La instalación debe ser realizada de conformidad con las Normas EN 12453
y EN 12445. El nivel de seguridad de la automación debe ser C+E.
11) Quiten la alimentación eléctrica antes de efectuar cualquier intervención
en la instalación.
12) Coloquen en la red de alimentación de la automación un interruptor
omnipolar con distancia de apertura de los contactos igual o superior a 3
mm. Se aconseja usar un magnetotérmico de 6A con interrupción omnipolar.
13) Comprueben que la instalación disponga línea arriba de un interruptor
diferencial con umbral de 0,03 A.
14) Verifiquen que la instalación de tierra esté correctamente realizada y
conecten las partes metálicas del cierre.
15) La automación dispone de un dispositivo de seguridad antiaplastamiento
constituido por un control de par. No obstante, es necesario comprobar el
umbral de intervención según lo previsto en las Normas indicadas en el punto
10.
16) Los dispositivos de seguridad (norma EN 12978) permiten proteger posibles
áreas de peligro de Riesgos mecánicos de movimiento, como por ej.
aplastamiento, arrastre, corte.
17) Para cada equipo se aconseja usar por lo menos una señalización luminosa
así como un cartel de señalización adecuadamente fijado a la estructura
del bastidor, además de los dispositivos indicados en el “16”.
18) GENIUS declina toda responsabilidad relativa a la seguridad y al buen
funcionamiento de la automación si se utilizan componentes de la instalación
que no sean de producción GENIUS.
19) Para el mantenimiento utilicen exclusivamente piezas originales GENIUS
20) No efectúen ninguna modificación en los componentes que forman parte
del sistema de automación.
21) El instalador debe proporcionar todas las informaciones relativas al
funcionamiento del sistema en caso de emergencia y entregar al usuario del
equipo el manual de advertencias que se adjunta al producto.
22) No permitan que niños o personas se detengan en proximidad del producto
durante su funcionamiento.
23) Mantengan lejos del alcance los niños los telemandos o cualquier otro
emisor de impulso, para evitar que la automación pueda ser accionada
involuntariamente.
HINWEISE FÜR DEN INSTALLATIONSTECHNIKER
ALLGEMEINE SICHERHEITSVORSCHRIFTEN
1) ACHTUNG! Um die Sicherheit von Personen zu gewährleisten, sollte die
Anleitung aufmerksam befolgt werden. Eine falsche Installation oder ein
fehlerhafter Betrieb des Produktes können zu schwerwiegenden
Personenschäden führen.
2) Bevor mit der Installation des Produktes begonnen wird, sollten
die Anleitungen
aufmerksam gelesen werden.
3) Das Verpackungsmaterial (Kunststoff, Styropor, usw.) sollte nicht in Reichweite
von Kindern aufbewahrt werden, da es eine potentielle Gefahrenquelle
darstellt.
4) Die Anleitung sollte aufbewahrt werden, um auch in Zukunft Bezug auf sie
nehmen zu können.
5) Dieses Produkt wurde ausschließlich für den in diesen Unterlagen
angegebenen Gebrauch entwickelt und hergestellt. Jeder andere
Gebrauch, der nicht ausdrücklich angegeben ist, könnte die Unversehrtheit
des Produktes beeinträchtigen und/oder eine Gefahrenquelle darstellen.
6) Die Firma GENIUS lehnt jede Haftung für Schäden, die durch unsachgemäßen
oder nicht bestimmungsgemäßen Gebrauch der Automatik verursacht
werden, ab.
7) Das Gerät sollte nicht in explosionsgefährdeten Umgebungen installiert
werden: das Vorhandensein von entflammbaren Gasen oder Rauch stellt ein
schwerwiegendes Sicherheitsrisiko dar.
8) Die mechanischen Bauelemente müssen den Anforderungen der Normen
EN 12604 und EN 12605 entsprechen.
Für Länder, die nicht der Europäischen Union angehören, sind für die
Gewährleistung eines entsprechenden Sicherheitsniveaus neben den
nationalen gesetzlichen Bezugsvorschriften die oben aufgeführten Normen
zu beachten.
9) Die Firma GENIUS übernimmt keine Haftung im Falle von nicht fachgerechten
Ausführungen bei der Herstellung der anzutreibenden Schließvorrichtungen
sowie bei Deformationen, die eventuell beim Betrieb entstehen.
10) Die Installation muß unter Beachtung der Normen EN 12453 und EN 12445
erfolgen. Die Sicherheitsstufe der Automatik sollte C+E sein.
11) Vor der Ausführung jeglicher Eingriffe auf der Anlage ist die elektrische
Versorgung abzunehmen.
12) Auf dem Versorgungsnetz der Automatik ist ein omnipolarer Schalter mit
Öffnungsabstand der Kontakte von über oder gleich 3 mm einzubauen.
Darüber hinaus wird der Einsatz eines Magnetschutzschalters mit 6A mit
omnipolarer Abschaltung empfohlen.
13) Es sollte überprüft werden, ob vor der Anlage ein Differentialschalter mit
einer Auslöseschwelle von 0,03 A zwischengeschaltet ist.
14) Es sollte überprüft werden, ob die Erdungsanlage fachgerecht ausgeführt
wurde. Die Metallteile der Schließung sollten an diese Anlage angeschlossen
werden.
15) Die Automation verfügt über eine eingebaute Sicherheitsvorrichtung für den
Quetschschutz, die aus einer Drehmomentkontrolle besteht. Es ist in jedem
Falle erforderlich, deren Eingriffsschwelle gemäß der Vorgaben der unter
Punkt 10 angegebenen Vorschriften zu überprüfen.
16) Die Sicherheitsvorrichtungen (Norm EN 12978) ermöglichen den Schutz
eventueller Gefahrenbereiche vor mechanischen Bewegungsrisiken, wie
zum Beispiel Quetschungen, Mitschleifen oder Schnittverletzungen.
17) Für jede Anlage wird der Einsatz von mindestens einem Leuchtsignal empfohlen
sowie eines Hinweisschildes, das über eine entsprechende Befestigung mit
dem Aufbau des Tors verbunden wird. Darüber hinaus sind die unter Punkt
“16” erwähnten Vorrichtungen einzusetzen.
18) Die Firma GENIUS lehnt jede Haftung hinsichtlich der Sicherheit und des
störungsfreien Betriebs der Automatik ab, soweit Komponenten auf der
Anlage eingesetzt werden, die nicht im Hause GENIUS hergestellt wurden.
19) Bei der Instandhaltung sollten ausschließlich Originalteile der Firma GENIUS
verwendet werden.
20) Auf den Komponenten, die Teil des Automationssystems sind, sollten keine
Veränderungen vorgenommen werden.
21) Der Installateur sollte alle Informationen hinsichtlich des manuellen Betriebs
des Systems in Notfällen liefern und dem Betreiber der Anlage das
Anleitungsbuch, das dem Produkt beigelegt ist, übergeben.
22) Weder Kinder noch Erwachsene sollten sich während des Betriebs in der
unmittelbaren Nähe der Automation aufhalten.
23) Die Funksteuerungen und alle anderen Impulsgeber sollten außerhalb der
Reichweite von Kindern aufbewahrt werden, um ein versehentliches
Aktivieren der Automation zu vermeiden.
24) Der Durchgang oder die Durchfahrt zwischen den Flügeln darf lediglich bei
vollständig geöffnetem Tor erfolgen.
25) Der Betreiber sollte keinerlei Reparaturen oder direkte Eingriffe auf der
Automation ausführen, sondern sich hierfür ausschließlich an qualifiziertes
Fachpersonal wenden.
26) Alle Vorgehensweisen, die nicht ausdrücklich in der vorliegenden Anleitung
vorgesehen sind, sind nicht zulässig
17) On recommande que toute installation soit doté au moins d'une signalisation
lumineuse, d'un panneau de signalisation fixé, de manière appropriée, sur la
structure de la fermeture, ainsi que des dispositifs cités au point “16”.
18) GENIUS décline toute responsabilité quant à la sécurité et au bon
fonctionnement de l'automatisme si les composants utilisés dans l'installation
n'appartiennent pas à la production GENIUS.
19) Utiliser exclusivement, pour l'entretien, des pièces GENIUS originales.
20) Ne jamais modifier les composants faisant partie du système d'automatisme.
21) L'installateur doit fournir toutes les informations relatives au fonctionnement
manuel du système en cas d'urgence et remettre à l'Usager qui utilise
l'installation les "Instructions pour l'Usager" fournies avec le produit.
22) Interdire aux enfants ou aux tiers de stationner près du produit durant le
fonctionnement.
23) Eloigner de la portée des enfants les radiocommandes ou tout autre
générateur d'impulsions, pour éviter tout actionnement involontaire de
l'automatisme.
24) Le transit entre les vantaux ne doit avoir lieu que lorsque le portail est
complètement ouvert.
25) L'Usager qui utilise l'installation doit éviter toute tentative de réparation ou
d'intervention directe et s'adresser uniquement à un personnel qualifié.
26) Tout ce qui n'est pas prévu expressément dans ces instructions est interdit.
24) Sólo puede transitarse entre las hojas si la cancela está completamente
abierta.
25) El usuario no debe por ningún motivo intentar reparar o modificar el producto,
debe siempre dirigirse a personal cualificado.
26) Todo lo que no esté previsto expresamente en las presentes instrucciones
debe entenderse como no permitido
4
ENGLISH
LINEAR AUTOMATION
The LINEAR automation system for swing gates comprises an
electromechanical operator which drives the gate leaves by
means of a worm screw.
The LINEAR operator is irreversible and locks mechanically when
the motor is not in use. Therefore a lock does not need to be fitted.
Its manualoveride is activated by a customised key.
The LINEAR automated systems were designed and manufactured
to control access of vehicles. Avoid any other use whatever.
1. DESCRIPTION AND TECHNICAL SPECIFICATIONS
Fig. 1
Fig. 2
Table 1:
Operator technical specifications
2. STANDARD INSTALLATION LAYOUT
1) Operators
2) Photocells
3) Control unit
4) Keyswitch
5) Receiver
6) Flashing light
Notes:1) Use suitable rigid/flexible pipes for laying power cables.
2) Always keep low voltage accessory cables separate from 230V~ power
cables. To avoid interference, use separate sheaths.
Drawing A
INSTALLATION DIMENSIONS
Fig. A
Fig. B
CALCULATING INSTALLATION DIMENSIONS:
GENERAL RULES
If the dimensions specified in Table A cannot be used,
calculate different dimensions as follows:
- For 90° leaf opening: a + b = c
- For leaf opening over 90°: a + b < c
- The lower the dimensions of a and b the higher the
gate speed. Ensure that current standards are
observed.
- Make sure that the difference between a and b is
no more than 4 cm: larger differences cause large
variations in speed during opening and closing.
- Due to the dimensions of the operator, the minimum
value for Z is 65 mm (fig. A)
If the dimensions of the gate post or the position of
the hinge do not allow a to be kept within the
required value, make a recess in the gate post as
shown in fig. B.
1) Motor Unit
2) Power cable
3) Worm screw
4) Front bracket
5) Rear bracket
Table A: Recommended dimensions (in mm)
(¹) useful rod stroke (²) max. dimension (³) min. dimension
Model
300
400
A B C (¹) D (²) Z (³) L
αα
αα
α
90°
110°
90°
110°
145 145
125 125
195 195
165 165
290
290
390
390
65
65
65
65
70
50
120
90
970
970
1170
1170
5
3
4
2
1
Power supply
Model
Absorbed power
Current drawn
Electric motor rpm
Thermal cutout
Capacitor
Max. thrust/traction force
Rod stroke
Rod speed
Temperature range
Operator weight
Housing protection
Duty cycle (cycles/hour)
Maximum leaf length
LINEAR
LENTO
230V~ - 50Hz 230V~ - 50Hz
24Vdc
350W 280W70W
1,5A 1,2A3A
1400 900
140°C 140°C
10 µF / 400V 8 µF / 400V
400 daN 320 daN300 daN
300 mm / 400 mm
1,6 cm/sec
-20°C +55°C
6,5 Kg
IP 44
20 2050
3 m / 4 m
LINEAR
24
LINEAR
400 mm
1,1 cm/sec
200 mm
150 mm
70 mm
B
A
Z
D
65 min.
L
5
ENGLISH
Fig. 3
Fig. 4
3) Release the operator (see paragraph 6).
4) Extend the rod to the end of its stroke (fig. 4).
5) Lock the operator (see paragraph 7).
6) Rotate the operator rod two full turns clockwise (fig. 4).
7) Fit the front bracket onto the rod as shown in fig. 5.
8) Close the gate leaf and, keeping the operator perfectly
horizontal, locate the leaf attachment position on the front
bracket (fig. 6).
3. INSTALLATION OF THE AUTOMATION SYSTEM
3.1. PRELIMINARY CHECKS
To ensure trouble-free operation, make sure that the gate (whether
existing or to be installed) has the following specifications:
max. length of each gate leaf: 3 metres (with operator with
300 mm stroke);
maximum length of each gate leaf: 4 metres (with operator
with 400 mm stroke);
strong and rigid leaf frame
smooth movement of leaves during entire travel; no stiff points
hinges in good condition
mechanical travel limit stops present
electric lock present in reversible version.
If any welding or brazing has to be done on the gate, this must
be done before installing the automation system.
Good condition of the structure is essential for reliability and
safety of the automation system.
3.2. INSTALLATION OF THE OPERATORS
1) Fix the rear bracket to the gate post according to the
instructions in Table A. Adjust the length of the bracket if
necessary.
Warning:
Observe the specified dimensions to ensure correct
operator operation.
In the case of iron gate posts, weld the bracket directly onto
the gate post.
In the case of brick/concrete gate posts, flush-mount a wall
plate (fig. 3), and weld the bracket to the plate.
2) Fix the operator to the rear bracket by means of the screws
supplied (fig. 3).
Fig. 5
9) Fix the front bracket temporarily to the leaf by two welds.
N.B.: If the gate frame does not allow for secure fixing of the
bracket, add a support plate.
10) Release the operator and ensure that the gate opens
smoothly with no stiff points and that it stops on the mechanical
travel stops.
11) Completely weld the front bracket to the leaf. When doing
this, detach the operator temporarily from the bracket to
prevent damage from welding scale.
N.B.:
1) Grease all pivots on brackets
2) If welding is not possible, the front and rear bracket plates
can be fixed using screws and screw anchors.
Fig. 6
6
ENGLISH
12) Fit the alluminium outer cover with the screws provided as
shown in fig. 7.
13) Attach the metal tag to the slot in the top section of the motor
in order to blank off the holes present as shown fig.8. On the
other hand, do not block the holes to be found in the lower
section.
Fig. 9
3
2
1
4
5
Fig. 10
3
4
5
2
1
14) Repeat the above operations to install the second operator,
if required.
15) Install the control unit box according to the dimensions given
in the relevant instructions.
4. STARTING THE AUTOMATED UNIT
CAUTION: Before attempting any work on the system or on the
operator, always turn off power.
Observe points 10, 11, 12, 13, 14 of the GENERAL SAFETY
OBLIGATIONS.
Observing the instructions in Fig.2, lay the raceways and make
the electric connections of the control board to the selected
accessories.
Always separate power cables from control and safety cables
(push-button, receiver, photocells, etc...). To prevent any electric
noise whatever, use separate sheaths.
1) Program the control board according to your needs observing
the concerning instructions.
2) Switch on power to the system and check the condition of
the LEDs according to the table of the control board
instructions.
5. TESTING THE AUTOMATED UNIT
Carefully check operation of the operator and all
accessories connected to it.
Give the customer the page entitled "End-User Guide". Describe
how the operator works and explain how it is to be used correctly.
Inform the customer of the potential hazard areas of the
automation.
6. MANUAL OPERATION
The gate can be operated manually in the event of a power
failure or malfunction by removing the plug and inserting the
special release key as shown in fig. 9.
To release the operator, turn the key as shown in fig. 9.
Open or close the leaves manually.
Fig. 7
Fig. 8
7. RETURNING TO NORMAL OPERATION
Turn off the electricity supply to the system before re-locking the
operators to avoid all risk of starting them accidentally.
To re-lock the operator, turn the key as shown in fig. 10.
8. SPECIAL APPLICATIONS
There are no special applications.
9. MAINTENANCE
Carry out periodic checks of the gate structure and ensure in
particular that the hinges are in perfect working condition.
Check periodically that the electronic anti-crushing system is
adjusted correctly and that the release mechanism for manual
movement is fully operative (see relevant paragraph).
Safety devices installed on the system must be checked every six
months.
10.REPAIRS
For repairs, contact authorised service centres.
Guida per l'utente - End-user guide - Instructions pour l'utilisateur -
Instrucciones para el usuario - Benutzerinformation
Linear
Fig. 1
ITALIANO
Leggere attentamente le istruzioni prima di utilizzare il
prodotto e conservarle per eventuali necessità future
NORME GENERALI DI SICUREZZA
L'automazione LINEAR, se correttamente installata ed utilizzata,
garantisce un elevato grado di sicurezza.
Alcune semplici norme di comportamento possono evitare
inoltre inconvenienti accidentali:
- Non transitare tra le ante quando queste sono in movimento.
Prima di transitare tra le ante, attendere l'apertura completa.
- Non sostare assolutamente tra le ante.
- Non sostare e non permettere a bambini,persone o cose di
sostare nelle vicinanze dell’automazione, evitandolo ancor
più durante il funzionamento.
- Tenere fuori dalla portata dei bambini, radiocomandi o
qualsiasi altro datore d’impulso per evitare che l'automazione
possa essere azionata involontariamente.
- Non permettere ai bambini di giocare con l’automazione.
- Non contrastare volontariamente il movimento delle ante.
- Evitare che rami o arbusti possano interferire col movimento
delle ante
- Mantenere efficienti e ben visibili i sistemi di segnalazione
luminosa.
- Non tentare di azionare manualmente le ante se non dopo
averle sbloccate.
- In caso di malfunzionamento, sbloccare le ante per consentire
l’accesso ed attendere l’intervento tecnico di personale
qualificato.
- Una volta predisposto il funzionamento manuale, prima di
ripristinare il funzionamento normale, togliere alimentazione
elettrica all’impianto.
- Non eseguire alcuna modifica sui componenti facenti parte
il sistema d’automazione.
- Astenersi da qualsiasi tentativo di riparazione o d’intervento
diretto e rivolgersi solo a personale qualificato.
- Far verificare almeno semestralmente l’efficienza
dell’automazione, dei dispositivi di sicurezza e del
collegamento di terra da personale qualificato.
DESCRIZIONE
L’automazione LINEAR è composta da due operatori
elettromeccanici ideali per il controllo di cancelli a battente
fino a 3 mt per anta, con operatori con corsa di 300 mm, e fino
a 4 mt per anta con operatori con corsa fino a 400 mm.
I due operatori elettromeccanici trasmettono il movimento
alle ante tramite un sistema a vite senza fine.
Il funzionamento degli operatori è gestito da una centralina
elettronica di comando, racchiusa in un contenitore con
adeguato grado di protezione agli agenti atmosferici.
Stabilire con il Tecnico installatore la logica di funzionamento
che si desidera impostare per il proprio cancello.
Le ante normalmente si trovano in posizione di chiusura.
Quando la centralina elettronica riceve un comando di
apertura tramite il radiocomando o qualsiasi altro datore di
impulso, aziona l’apparato elettromeccanico ottenendo la
rotazione delle ante, fino alla posizione di apertura che consente
l’accesso.
Per il dettagliato comportamento dell'automazione nelle
diverse logiche di funzionamento, fare riferimento al Tecnico
installatore.
Nelle automazioni sono presenti dispositivi di sicurezza
(fotocellule) che impediscono il movimento delle ante quando
un ostacolo si trova nella zona da loro protetta.
L'automazione LINEAR dispone di serie di un dispositivo
elettronico di sicurezza antischiacciamento che limita la coppia
trasmessa alle ante.
Gli operatori LINEAR garantiscono il blocco meccanico
quando il motore non è in funzione, e quindi non è necessario
installare alcuna serratura.
L’apertura manuale è quindi possibile solo intervenendo
sull’apposito sistema di sblocco.
La segnalazione luminosa indica il movimento in atto delle
ante.
FUNZIONAMENTO MANUALE
Nelle automazioni dove è stato montato l'operatore LINEAR,
nel caso sia necessario azionare manualmente il cancello a
causa di mancanza di corrente o disservizio dell’automazione,
è necessario togliere il tappo di protezione ed inserire l'apposita
chiave in dotazione nel sistema di sblocco come da fig. 1.
Per sbloccare l'operatore ruotare la chiave come da fig. 1.
Effettuare manualmente l'operazione di apertura o chiusura
delle ante.
Fig. 2
3
2
1
4
5
3
4
5
2
1
ENGLISH
FRANÇAIS
RIPRISTINO DEL FUNZIONAMENTO NORMALE
Per evitare che un impulso involontario possa azionare gli
operatori durante la manovra, prima di ribloccare gli operatori,
togliere alimentazione all’impianto.
Per ribloccare l'operatore ruotare la chiave come da fig. 2 .
Read the end-user guide carefully before using the product
and keep it in a safe place for future reference.
GENERAL SAFETY REGULATIONS
When correctly installed and used, the LINEAR automation
system ensures a high degree of safety.
A few simple rules should be followed to prevent accidental
problems.
- Do not pass through the gate while the leaves are still moving:
always wait until they have opened completely.
- Do not stand between the leaves.
- Do not stand near the automation system; do not allow
children or adults to stand near it; and do not leave objects
near it.
- Keep control devices or other devices that might accidentally
activate the automation system out of the reach of children.
- Do not allow children to play with the automation system.
- Do not obstruct movement of the leaves.
- Do not allow branches or bushes to obstruct movement of
the leaves.
- Ensure that the warning lamps are in always in working order
and visible.
- Do not attempt to actuate the leaves manually unless you
have first unlocked them.
- In case of a malfunction, unlock the leaves to allow vehicles
to pass through, and call a qualified technician.
- If you have set manual mode, disconnect the power supply
before restoring normal operation.
- Do not modify the components of the automation system.
- Do not attempt to repair the automation system or to perform
any operation on it. Call qualified technicians only.
- At least once every 6 months, have qualified personnel
check that the automation system, safety devices and earth
connection are in working order.
DESCRIPTION
The LINEAR automation consists of two electromechanical
operators which are ideal for controlling swinging gates with
leaves up to 3 m long each with operators with a 300mm stroke,
and up to 4 m long each with operators with stroke up to 400
mm.
The two electromechanical operators transmit movement to
the leaves by a worm screw system.
The operators are controlled by an electronic control unit
mounted in an enclosure which assures adequate protection
against atmospheric agents.
Together with the installation technician, decide on the type of
operation you want to set for your gate.
The leaves are normally closed. When the electronic control
unit receives an open command from the remote radio control
or any other control device, it activates the electromechanical
system and causes the leaves to turn to the open position so
as to permit access.
For detailed information on the operation of the automation
system in the various operating modes, contact the installation
technician.
The automation system is equipped with a photocell safety
device which prevents the leaves from closing when the
photocells are darkened by an obstacle.
The LINEAR automation system is also equipped with an anti-
crushing safety device (fitted as standard) that limits the torque
transmitted to the leaves.
The LINEAR operators ensure that the system is mechanically
locked when the motor is not running, so there is no need to
install a lock.
The leaves can be opened manually only by operating the
unlocking device.
The lamp flashes while the leaves are moving.
MANUAL OPERATION
In automation systems fitted with the LINEAR operator, if the
gate has to be operated manually due to a malfunction or
power supply failure, remove the safety cap and insert the key
provided into the release system as shown in fig. 1.
To release the operator, turn the key as shown in fig. 1.
Open or close the leaf manually.
RETURNING TO NORMAL OPERATION
Turn off the electricity supply to the system before re-locking
the operators to avoid all risk of them starting accidentally
during this operation.
To re-lock the operator, turn the key as shown in fig. 2.
Lire attentivement les instructions avant d'utiliser le produit et
conserver la notice d'instructions pour toute consultation ultérieure.
RÈGLES DE SÉCURITÉ
L’automatisme LINEAR, si correctement installé et utilisé, garantit
un haut degré de sécurité.
L’observation des simples règles de comportement suivantes
permettra d’éviter de fâcheux inconvénients:
- Ne pas s’engager portail en mouvement. Il faut toujours
attendre l’ouverture complète du portail avant de s’engager.
- Ne pas stationner entre les vantaux.
- Ne pas stationner et empêcher quiconque de stationner à
proximité de l’automatisme, notamment pendant son
fonctionnement.
- Tenir à l’écart des enfants toutes radiocommandes ou
n’importe quel autre générateur d’impulsions, afin d’éviter
toute manoeuvre accidentelle de l’automatisme.
- Empêcher les enfants de jouer avec l’automatisme.
- Ne pas arrêter volontairement le mouvement du portail.
- Éviter que toutes branches ou tous arbustes puissent entraver
le mouvement du portail
- Toujours conserver efficaces et bien visibles les systèmes de
signalisation lumineuse.
- Ne pas tenter d’actionner manuellement le portail si ce n’est
qu’après son déverrouillage.
- En cas de mauvais fonctionnement, déverrouiller le portail
pour permettre le passage et attendre l’intervention d’un
technicien spécialisé.
- Avant de rétablir le fonctionnement normal du système,
après que le portail ait été déverrouillé pour être actionné
manuellement, il faut couper l’alimentation en énergie
électrique au système.
- Ne pas procéder à des modifications des composants du
système.
ESPAÑOL
- S’abstenir de faire toute tentative de réparation ou
d’intervention directe, et demander uniquement
l’intervention d’un technicien spécialisé.
- Faire vérifier semestriellement au moins l’efficacité de
l’automatisme, des dispositifs de sécurité et de la mise à la
terre par un technicien spécialisé.
DESCRIPTION
L’automatisme LINEAR est constitué de deux opérateurs
électromécaniques expressément conçus pour des vantaux
jusqu'à 3 mètres de largeur, avec des opérateurs ayant une
course de 300, et jusqu'à 4 mètres de largeur avec des
opérateurs ayant une course de 400 mm.
Les deux opérateurs électromécanique transmettent le
mouvement au portail par un système à vis sans fin.
Le fonctionnement des opérateurs est géré par une armoire
de manoeuvre électronique logée dans un coffret ayant un
indice de protection (IP) adéquat.
Déterminer, avec l'installateur, le type de logique de
fonctionnement du portail que l'on désire programmer.
Les vantaux sont normalement en position de fermeture.
Après la réception d’une commande d’ouverture par une
radiocommande ou n’importe quel autre générateur
d’impulsions, la platine électronique actionne l’opérateur qui
actionnent les vantaux, jusqu’à l'angle d’ouverture permettant
l’accès.
Pour le comportement détaillé de l’automatisme dans les
diverses logiques de fonctionnement, adressez-vous à votre
installateur.
Les automatismes peuvent être équipés de dispositifs de
sécurité (cellules photo-électriques) qui empêchent la
fermeture du portail en présence d’un obstacle dans leur zone
de surveillance.
L’automatisme LINEAR dispose, de série, d’une sécurité anti-
écrasement qui permet de limiter la force transmise aux
vantaux (limiteur constitué d’un embrayage).
Les opérateurs LINEAR garantissent le blocage mécanique
quand le moteur est arrêté ne nécessitant pas l’installation
d’une serrure.
L’ouverture manuelle n’est donc possible qu’en manoeuvrant
le système de déverrouillage adéquat.
La signalisation lumineuse indique le mouvement en cours du
portail.
FONCTIONNEMENT MANUEL
Dans le cas où le portail doit être actionné manuellement à la
suite d’une coupure de courant ou d’une défaillance de
l’automatisme, il faut impérativement ôter le bouchon de
protection et insérer la clé appropriée (fournie) dans le système
de déverrouillage comme indiqué Fig.1., pour les automatismes
prévoyant l'opérateur LINEAR.
Pour rebloquer l’opérateur, tourner la clé comme indiqué
Fig.1.
Effectuer manuellement la manoeuvre d’ouverture ou de
fermeture du portail.
RÉTABLISSEMENT DU FONCTIONNEMENT NORMAL
Pour éviter qu’une impulsion involontaire puisse actionner le
portail pendant la manoeuvre, il faut couper l’alimentation en
énergie électrique au système avant de rétablir le
fonctionnement normal.
Pour rebloquer l’opérateur, tourner la clé comme indiqué
Fig.2.
Leer atentamente las instrucciones antes de utilizar el
producto y conservarlas para futuras referencias.
NORMAS GENERALES DE SEGURIDAD
El automatismo LINEAR, si está correctamente instalado y se
emplea de la manera debida, garantiza un elevado grado de
seguridad.
Algunas sencillas normas de comportamiento pueden evitar
inconvenientes accidentales:
- No pasar entre las hojas de la cancela cuando se encuentren
aún en movimiento. Antes de cruzar la cancela, esperar
hasta que se haya abierto por completo.
- No detenerse en ningún momento entre las hojas de la
cancela.
- Controlar que ninguna persona ni objeto permanezca en
proximidad del automatismo, especialmente durante el
funcionamiento del mismo.
- No dejar al alcance de los niños radiomandos ni otros
generadores de impulsos, para evitar que el automatismo
sea accionado involuntariamente.
- No permitir que los niños jueguen con el automatismo.
- No oponer resistencia al movimiento de la cancela.
- Evitar que ramas o arbustos interfieran con el movimiento de
la cancela.
- Mantener eficaces y bien visibles los sistemas de señalización
luminosa.
- No tratar de accionar la cancela a mano sin haberla
desbloqueado previamente.
- En caso de fallo, desbloquear la cancela para permitir el
tránsito y solicitar la intervención de personal técnico
calificado.
- Una vez activado el funcionamiento manual, antes de
restablecer la modalidad normal, desconectar la
alimentación eléctrica del sistema.
- No efectuar ninguna modificación en los componentes del
sistema de automatización.
- Abstenerse de todo intento de reparación o de intervención
directa, y recurrir sólo a personal calificado.
- Al menos cada seis meses, hacer controlar por un técnico
calificado la eficacia del automatismo, de los dispositivos de
seguridad y de la conexión de tierra.
DESCRIPCIÓN
El automatismo LINEAR está formado por dos actuadores
electromecánicos, que pueden controlar cancelas de
batiente de hasta 3 m por hoja utilizando actuadores con
carrera de 300 mm, o hasta 4 m mediante actuadores con
carrera de 400 mm.
Los dos actuadores electromecánicos transmiten el
movimiento a las hojas mediante un sistema de tornillo sin fin.
El funcionamiento de los actuadores está controlado por una
central electrónica de mando, y está se instala dentro de un
contenedor que la protege de los agentes atmosféricos.
Convenir con el técnico instalador la lógica de funcionamiento
de la cancela.
Normalmente, las hojas quedan cerradas.
Cuando la central electrónica recibe un mando de apertura
desde el radiomando o desde cualquier otro generador de
impulsos, acciona el dispositivo electromecánico provocando
la rotación de las hojas hasta la posición de apertura, que
permite el acceso.
Para una descripción detallada del comportamiento del
automatismo en las distintas lógicas de funcionamiento,
consultar con el técnico instalador.
Los automatismos están dotados de elementos de seguridad
(fotocélulas) que impiden que la cancela se cierre cuando
hay un obstáculo en su radio de acción.
El automatismo LINEAR trae montado de serie un dispositivo de
seguridad antiaplastamiento que limita el par transmitido a las
hojas.
DEUTSCH
Los actuadores LINEAR garantizan el bloqueo mecánico
cuando el motor no está en marcha, por lo cual no es necesario
instalar ninguna cerradura.
Para poder abrir la cancela a mano, es necesario accionar
previamente el sistema de desbloqueo.
La señalización luminosa indica el movimiento que está
realizando la cancela.
FUNCIONAMIENTO MANUAL
En los automatismos equipados con el actuador LINEAR, si es
accionar la cancela manualmente a causa de un corte de
corriente o fallo del automatismo, quitar el tapón de protección
e introducir la llave en el sistema de desbloqueo (fig. 1).
Para desbloquear el actuador, hacer girar la llave (fig. 1).
Abrir o cerrar las hojas a mano.
REANUDACIÓN DEL FUNCIONAMIENTO NORMAL
Para evitar que un impulso involuntario accione los actuadores
durante la maniobra, antes de volver a bloquearlos,
desconectar la alimentación eléctrica del equipo.
Para volver a bloquear el actuador, hacer girar la llave (fig. 2).
Die Anleitungen vor Gebrauch des Produkts aufmerksam
durchlesen und für künftigen Bedarf aufbewahren.
ALLGEMEINE SICHERHEITSVORSCHRIFTEN
Bei fachgerechter Installation und vorschriftsmäßigem
Gebrauch gewährleistet der Antrieb LINEAR einen hohen
Sicherheitsgrad.
Die Beachtung einiger einfacher Verhaltensnormen kann
etwaige Gefahrensituationen weitestgehend vermeiden:
- Nicht durch die Torflügel während ihrer Bewegungsphase
fahren, erst auf die vollständige Öffnung derselben warten.
- Der Aufenthalt zwischen den Torflügeln ist streng verboten.
- Das Abstellen von Gegenständen und der Aufenthalt im
Umfeld des Antriebs ist nicht zulässig und Kindern sowie
anderen Personen zu verbieten. Dies gilt insbesondere
während der Antriebsfunktion.
- Funksteuerungen oder sonstige Impulsgeber sind außerhalb
der Reichweite von Kindern aufzubewahren, um eine
unbeabsichtigte Betätigung des Antriebs zu verhindern.
- Kindern ist das Spielen mit dem Antrieb zu untersagen.
- Den Bewegungsablauf der Torflügel nicht willkürlich
behindern.
- Äste oder Sträucher dürfen die Torbewegung nicht
beeinträchtigen.
- Die Lichtsignale müssen einwandfrei funktionieren und gut
sichtbar sein.
- Die manuelle Betätigung der Torflügel darf erst nach der
Entriegelung erfolgen.
- Bei Betriebsstörungen die Torflügel zwecks Durchfahrt
entriegeln und den technischen Eingriff des qualifizierten
Fachpersonals abwarten.
- Nach Schaltung auf den manuellen Betrieb muß die Anlage
vor Wiederaufnahme der normalen Funktion von der
Stromversorgung getrennt werden.
- Die Umrüstung jeglicher Antriebskomponenten ist strikt
verboten.
- Auf keinen Fall eigenmächtige Reparaturen bzw. Eingriffe
vornehmen, sondern damit ausschließlich qualifiziertes
Fachpersonal beauftragen.
- Die Funktionstüchtigkeit von Antrieb, Sicherheitsvorrichtungen
und Erdungsanlage mindestens alle 6 Monate durch
Fachpersonal überprüfen lassen.
BESCHREIBUNG
Bei LINEAR handelt es sich um zwei elektromechanische
Flügeltorantriebe für Flügel bis 3m Länge im Fall von Antrieben
mit 300mm Nutzhub sowie für Flügel bis 4m Länge bei Antrieben
mit 400mm Nutzhub.
Die Bewegungsübertragung an die Torflügel erfolgt mit einem
Spindelsystem.
Die Antriebe werden durch ein elektronisches Steuergerät mit
witterungsgeschütztem Gehäuse gesteuert.
Gemeinsam mit dem Installateur die jeweilige Betriebslogik
des Torantriebs absprechen.
Die Torflügel befinden sich normalerweise in Schließstellung.
Bei Empfang eines Öffnungssignals durch die Funksteuerung
bzw. sonstige Impulsgeber betätigt das elektronische
Steuergerät die Elektromechanik und bewirkt somit eine
Flügeldrehung in Öffnungs- bzw. Durchfahrtsstellung.
Über das genaue Verhalten des Antriebs in den einzelnen
Betriebslogiken gibt der Installateur gern Auskunft.
Die Sicherheitsvorrichtungen des Antriebs (Lichtschranken)
verhindern die Flügelbewegung bei einem Hindernis in ihrem
Wirkungsbereich.
Der Antrieb LINEAR ist serienmäßig mit einem Einklemmschutz-
System zur Begrenzung des Drehmoments an die Torflügel
ausgerüstet.
Die Antriebe LINEAR gewährleisten die mechanische
Verriegelung bei stehendem Motor, so daß sich der Einbau von
Elektroschlössern erübrigt.
Für die manuelle Öffnung ist daher das entsprechende
Entriegelungssystem zu betätigen.
Das Lichtsignal zeigt die ablaufende Flügelbewegung an.
MANUELLER BETRIEB
Sollte im Fall des Antriebs LINEAR ein manueller Torbetrieb
infolge von Stromausfällen bzw. Betriebsstörungen erforderlich
sein, Schutzstöpsel abnehmen und mitgelieferten Schlüssel
gemäß Abb. 1 in das Entriegelungssystem stecken.
Um der Antrieb zu lösen dreht man die Schlussel(Abb.1)
Die Flügel von Hand öffnen bzw. schließen.
NORMALEN BETRIEB WIEDERHERSTELLEN
Vor Verriegelung des Antriebs die Stromzufuhr der Anlage
unterbrechen, damit eine unbeabsichtigte Betätigung der
Torflügel verhindert wird.
Um der Antrieb wider zu blockieren dreht man die
Schlussel(Abb.2).
note - notes - note - notas - anmerkung
I0010L REV.4
GENIUS s.r.l.
Via Padre Elzi, 32
24050 - Grassobbio
BERGAMO-ITALY
tel. 0039.035.4242511
fax. 0039.035.4242600
www.geniusg.com
Timbro rivenditore: / Distributor’s stamp: / Timbre de l’agent: /
Sello del revendedor: / Fachhändlerstempel:
Le descrizioni e le illustrazioni del presente manuale non sono
impegnative. GENIUS si riserva il diritto, lasciando inalterate le
caratteristiche essenziali dell’apparecchiatura, di apportare in
qualunque momento e senza impegnarsi ad aggiornare la
presente pubblicazione, le modifiche che essa ritiene conve-
nienti per miglioramenti tecnici o per qualsiasi altra esigenza di
carattere costruttivo o commerciale.
The descriptions and illustrations contained in the present
manual are not binding. GENIUS reserves the right, whils leav-
ing the main features of the equipments unaltered, to under-
take any modifications to holds necessary for either technical
or commercial reasons, at any time and without revising the
present publication.
Les descriptions et les illustrations du présent manuel sont
fournies à titre indicatif. GENIUS se réserve le droit d’apporter à
tout moment les modifications qu’elle jugera utiles sur ce
produit tout en conservant les caractéristiques essentielles,
sans devoir pour autant mettre à jour cette publication .
Las descripciones y las ilustraciones de este manual no
comportan compromiso alguno. GENIUS se reserva el derecho,
dejando inmutadas las características esenciales de los
aparatos, de aportar, en cualquier momento y sin
comprometerse a poner al día la presente publicación, todas
las modificaciones que considere oportunas para el
perfeccionamiento técnico o para cualquier otro tipo de
exigencia de carácter constructivo o comercial.
Die Beschreibungen und Abbildungen in vorliegendem
Handbuch sind unverbindlich. GENIUS behält sich das Recht
vor, ohne die wesentlichen Eigenschaften dieses Gerätes zu
verändern und ohne Verbindlichkeiten in Bezung auf die
Neufassung der vorliegenden Anleitungen, technisch bzw,
konstruktiv / kommerziell bedingte Verbesserungen
vorzunehmen.
DICHIARAZIONE CE DI CONFORMITÁ
Fabbricante: GENIUS S.p.a.
Indirizzo: Via Padre Elzi, 32
24050 - Grassobbio
BERGAMO - ITALIA
Dichiara che: L'Attuatore mod. LINEAR
• è costruito per essere incorporato in una macchina o per
essere assemblato con altri macchinari per costituire una
macchina ai sensi della Direttiva 2006/42/CE;
• è conforme ai requisiti essenziali di sicurezza delle seguenti
altre direttive CEE:
• 2006/95/CE direttiva Bassa Tensione.
• 2004/108/CE direttiva Compatibilità elettromagnetica.
Inoltre dichiara che non è consentito mettere in servizio il
macchinario fino a che la macchina in cui sarà incorporato o
di cui diverrà componente sia stata identificata e ne sia stata
dichiarata la conformità alle condizioni della Direttiva 2006/42/
CEE e successive modifiche.
Grassobbio, 30.12.2009
L’Amministratore Delegato
D. Gianantoni
CE DECLARATION OF CONFORMITY
Manufacturer: GENIUS S.p.a.
Address: Via Padre Elzi, 32
24050 - Grassobbio
BERGAMO - ITALY
Hereby declares that: the LINEAR
• is built to be integrated into a machine or to be assembled
with other machinery to create a machine under the provisions
of Directive 2006/42/EEC;
• conforms to the essential safety requirements of the following
EEC directives:
• 2006/95/EC Low Voltage directive.
• 2004/108/EC Electromagnetic Compatibility directive.
and also declares that it is prohibited to put into service the
machinery until the machine in which it will be integrated or
of which it will become a component has been identified and
declared as conforming to the conditions of Directive 2006/42/
EEC and subsequent modifications.
Grassobbio, 30.12.2009
Managing Director
D. Gianantoni
DÉCLARATION CE DE CONFORMITÉ
Fabricant: GENIUS S.p.a.
Adresse:
Via Padre Elzi, 32
24050 - Grassobbio
BERGAMO - ITALIE
Déclare d’une part que l'automatisme mod. LINEAR
• est construit pour être incorporé dans une machine ou pour
être assemblé à d’autres appareillages, afin de constituer une
machine conforme aux termes de la Directive 2006/42/CE;
• est conforme aux exigences essentielles de sécurité des
directives CEE suivantes:
• 2006/95/CE directive Basse Tension.
• 2004/108/CE directive Compatibilité Électromagnétique.
On déclare en outre que la mise en service de l’outillage est
interdite tant que la machine à laquelle il sera incorporé ou
dont il deviendra un composant n’a pas été identifiée et
déclarée conforme aux conditions de la Directive 2006/42/
CEE et modifications successives.
Grassobbio, le 30.12.2009
L’Administrateur Délégué
D. Gianantoni
DECLARACIÓN CE DE CONFORMIDAD
Fabricante: GENIUS S.p.a.
Dirección: Via Padre Elzi, 32
24050 - Grassobbio
BERGAMO - ITALIA
Declara que: El equipo automático mod. LINEAR
• ha sido fabricado para ser incorporado en una máquina o
para ser ensamblado con otras maquinarias para constituir
una máquina de conformidad con la Directiva 2006/42/CE;
• cumple con los requisitos esenciales de seguridad de las
siguientes directivas CEE:
• 2006/95/CE directiva de Baja Tensión.
• 2004/108/CE directiva de Compatibilidad Electromagnética.
Asimismo declara que no está permitido poner en
funcionamiento la maquinaria hasta que la máquina en la
que deberá incorporarse o de la cual será un componente
haya sido identificada y se haya declarado su conformidad
con las condiciones de la Directiva 2006/42/CEE y sucesivas
modificaciones.
Grassobbio, 30.12.2009.
Administrador Delegado
D. Gianantoni
CE-KONFORMITÄTSERKLÄRUNG
Hersteller: GENIUS S.p.a.
Adresse: Via Padre Elzi, 32
24050 - Grassobbio
BERGAMO - ITALIEN
erklärt hiermit, daß: der Antrieb Mod. LINEAR
• hergestellt wurde, um in eine Maschine eingebaut oder mit
anderen Maschinen zu einer Maschine zusammengebaut zu
werden, gemäß der Richtlinien 2006/42/EG;
• den wesentlichen Sicherheitsanforderungen der folgenden
EWG-Richtlinien entspricht:
• 2006/95/EG Niederspannungsrichtlinie.
•2004/108/EG Richtlinie zur elektromagnetischen Verträglichkeit.
und erklärt außerdem, dass die Inbetriebnahme solange
untersagt ist, bis die Maschine, in welche diese Maschine
eingebaut wird oder von der sie ein Bestandteil ist, bestimmt
wurde und deren Übereinstimmung mit den Voraussetzungen
der Richtlinie 2006/42/EWG und nachträgliche Änderungen.
Grassobbio, 30.12.2009
Der Geschäftsführer
D. Gianantoni
1 / 1

Genius Linear Istruzioni per l'uso

Categoria
Gate Opener
Tipo
Istruzioni per l'uso