Pottinger NOVACAT 301 ALPHA MOTION RC Istruzioni per l'uso

Operator‘s manual

Translation of the original Operating Manual

Nr.

Disc mower

99+3751.EN.80X.0

NOVACAT 261 alpha motion master

(Type PSM 3750 : + . . 00001)

NOVACAT 261 alpha motion pro /ED /RC /RCB

(Type PSM 3753 : + . . 00001)

NOVACAT 301 alpha motion master

(Type PSM 3760 : + . . 00001)

NOVACAT 301 alpha motion pro /ED /RC/RCB

(Type PSM 3763 : + . . 00001)

NOVACAT 351 alpha motion master

(Type PSM 3810 : + . . 00001)

NOVACAT 351 alpha motion pro /ED /RC/RCB

(Type PSM 3813 : + . . 00001)

1900_GB-PAGE 2

Product liability, information obligation

Product liability obliges manufacturers and dealers to issue operating instructions for the machine at the point of sale and to instruct

the customer on the operation, safety and maintenance regulations governing the machine.

Confirmation is required to prove that the machine and the operating instructions have been properly handed over. For this purpose

you have received a confirmation e-mail from Pöttinger. If you have not received this mail, please contact your local dealer. Your

dealer can fill in the handover declaration online.

For the purposes of product liability law, every farmer is an entrepreneur.

In the terms of product liability law, damage to property is any damage arising due to the machine, but not to the machine, and an

excess (500 euros) exists for this liability.

Corporate damage to property within the terms of the product liability law is excluded from this liability.

Be advised! The operating instructions must also be handed over with any subsequent machine sale or transfer and the transferee

must be instructed in the regulations stated.

Pöttinger - Trust creates Afnity - since 1871

"Quality pays for itself." Therefore we apply the highest quality standards to our products which are constantly monitored by our

in-house quality management and our management board. Because the safety, perfect function, highest quality and absolute

reliability of our machines in operation are the core competencies for which we stand.

There may be deviations between these instructions and the product as we are constantly developing our products. Therefore no

claims may be derived from the data, illustrations and descriptions. Please contact your Specialist Service Centre for any binding

information about specific features of your machine.

We would ask you to please understand that changes to the scope of supply with regard to form, equipment and technical

specifications are possible at any time.

Any form of reprint, translation or reproduction, including excerpts, requires the written approval of Pöttinger Landtechnik GmbH.

All rights according to copyright laws remain expressly reserved by Pöttinger Landtechnik GmbH.

Refer to PÖTPRO for additional information about your machine:

Are you looking for suitable accessories for your machine? No problem! All the information you require is here at your disposal.

Scan the QR code on the machine's type plate or look under www.poettinger.at/poetpro

And if we don't have what your looking for, then your Specialist Service Centre is there for you with help and advice.

DE-1901 Dokum D Attachments - 3 -

PÖTTINGER Landtechnik GmbH

Industriegelände 1

4710 Grieskirchen, Austria

Tel. 07248 / 600 -0

Telefax 07248 / 600-2511

Please place a cross where appropriate. X

According to the product liability please check the above mentioned items.

INSTRUCTIONS FOR PRODUCT HANDOVER

Confirmation is required to prove that the machine and the operating instructions have been properly handed over. For this purpose you have

received a confirmation e-mail from Pöttinger. If you have not received this mail, please contact your local dealer. Your dealer can fill in the hand-

over declaration online.

 Machine checked according to delivery note. All attached parts removed. All safety equipment, drive shaft and operating

devices at hand.

 Operation, commissioning and maintenance of the machine or device discussed and explained to the customer on the basis

of the operating instructions.

 Check tyres for correct air pressure.

 Check wheel nuts for tight t.

 Correct PTO shaft speed indicated.

 Adaptation to the tractor carried out: Three point adjustment

 Cardan shaft correctly cut to length.

 Test run carried out and no defects detected.

 Function explanation during test run.

 Swivel in transport and working position explained.

 Information about optional equipment is given.

 Indication of unconditional reading of the operating instructions.

EN

- 4 -

2300_EN-Inhalt_3751

Table of conTenTs

EN

Table of contents

SYMBOLS USED

CE mark .....................................................................5

Safety hints: ............................................................... 5

Introduction ...............................................................6

WARNING SIGNS

Meaning of warning signs ..........................................7

Position of the warning signs ....................................9

ATTACHING TO TRACTOR

Safety advice ...........................................................10

Attaching in general ................................................. 10

Cardan shaft ............................................................10

Attaching problems .................................................10

Mudguards and protective cloths............................11

Hydraulic side guards .............................................. 11

Transport position ..................................................11

Road Transport ........................................................12

Top linkage ..............................................................12

Parking the machine ................................................ 12

MOUNTING UNIT "ALPHA MOTION"

General safety information ......................................13

Parking position ....................................................... 13

Transport position ...................................................13

Mounting ..................................................................13

Set spring tension ....................................................15

STARTING WORK

Safety advice ...........................................................16

Important notes prior to starting work ..................... 16

Set cutting height1) ..................................................17

Mowing ....................................................................17

Reversing ................................................................. 18

SWATH FORMER

Overview and Function ............................................ 19

Possible settings .....................................................19

Maintenance ............................................................20

Removal and installation of the swath former .........20

Optional Equipment ................................................. 20

ED TINE CONDITIONER

Operation mode .......................................................21

General safety information ......................................21

Possible settings .....................................................21

Operation ................................................................. 22

Maintenance ............................................................23

Detaching and attaching the conditioner ................24

Rotor tines: ..............................................................24

Position of the rotor tines on the conditioner ..........25

RC = ROLLER CONDITIONER

Safety advice ...........................................................27

Overview and Function ............................................ 27

Possible settings .....................................................27

Operation ................................................................. 29

Maintenance ............................................................30

REPLACE CONDITIONER

Overview .................................................................. 33

Left-Right-Balance ..................................................33

Remove conditioner ................................................33

Attach conditioner ...................................................34

GENERAL MAINTENANCE

Safety advice ...........................................................35

General maintenance information ...........................35

Cleaning of machine parts .......................................35

Parking in the open ..................................................35

Winter storage .........................................................35

Articulated shafts ..................................................... 36

Hydraulic unit ...........................................................36

Cutter bar oil level check .........................................37

Oil change on cutter bar ..........................................38

Angular gear ...........................................................38

Installing cutter blades ...........................................39

MAINTENANCE

Wear control of mowing blades and holder ............40

Storing of the lever ..................................................41

Storing of the lever ..................................................42

TECHNICAL DATA

Technical data .........................................................43

Optional equipment: ................................................43

Necessary connections ...........................................43

Type plate ................................................................44

The designated use of the mower unit ....................44

Type plate position ..................................................44

SUPPLEMENT

SAFETY ADVICE

Lubrication chart ......................................................51

NOVACAT 261 alpha motion pro /ED /RC /RCB ....52

NOVACAT 301 alpha motion pro /ED /RC /RCB ....52

NOVACAT 351 alpha motion pro /ED /RC /RCB ....52

NOVACAT 261 alpha motion master .......................53

NOVACAT 301 alpha motion master .......................53

NOVACAT 351 alpha motion master .......................53

Lubricants ................................................................ 54

TAPER BUSHES

Taper bushes installation instructions .....................57

Combination of tractor and mounted implement ....58

- 5 -

1801_EN-Sicherheit ANSI

EN

SymbolS uSed

CE mark

The CE mark, which is affixed by the manufacturer, indicates outwardly that this machine conforms to the engineering

guideline regulations and the other relevant EU guidelines.

EU Declaration of Conformity (see Attachment)

By signing the EU Declaration of Conformity, the manufacturer declares that the machine that

is brought into service complies with all relevant fundamental safety and health requirements.

Safety hints:

These Operating Instructions contain the

following Figures:

DANGER

If you do not follow the instructions in a text section

with this marking, there is a risk of fatal or life-

threatening injury.

• All instructions in such text sections must be

followed!

WARNING

If you do not observe the instructions marked this

way, there is the risk of a severe injury.

• All instructions in such text sections must be

followed!

CAUTION

If you do not observe the instructions marked this

way, there is the risk of an injury.

• All instructions in such text sections must be

followed!

NOTE

If you do not observe the instructions marked this

way, there is the risk of material damage.

• All instructions in such text sections must be

followed!

TIP

The text sections marked in this way provide you with

special recommendations and advise regarding the

economical use of the implement.

ENVIRONMENT

The text sections marked in this way provide practices

and advice on environmental protection.

The features marked as (optional) are only available as

standard with specific implement versions or are only

offered for specific versions as optional equipment or are

only offered in certain countries.

Figures may deviate from your implement in detail and are

to be taken as illustrations of operating principle.

Designations such as right and left always apply as the

direction of travel unless the text or illustrations clearly

show otherwise.

- 6 -

EN

IntroductIon

1700_GB-Introduction

Introduction

Dear Customer

These Operating Instructions are intended to allow you

to familiarise yourself with the implement and provide

you with clear information on safe and correct handling,

care and maintenance. Thus please take the time to read

these Instructions.

These Operating Instructions comprise part of the imple-

ment. They are to be kept at a suitable location and acces-

sible to staff over the entire service life of the implement.

Instructions based on the national provisions regarding

protection against accidents, road traffic and environmental

protection are also to be applied additionally.

Any persons commissioned with the operation, maintenance

or transport of the implement must read and understand

these Instructions, in particular the safety information, prior

to starting work. Any warranty claims lapse on non-obser-

vance of these Instructions.

In case you have questions related to this operation manual

or further questions about this implement, please contact

your dealer.

Care and maintenance performed in good time and scru-

pulously according to the maintenance intervals specified

ensure operational and traffic safety as well as the reliability

of the implement.

Use only the original spare parts and accessories from

Pöttinger or accepted by Pöttinger. For those parts relia-

bility, safety and suitability for Pöttinger machines can be

assured. Warranty claims lapse if non-approved parts are

used. The use of original parts is also recommended after

the warranty period has expired to maintain the performance

of the implement in the long term.

Product liability legislation obliges the manufacturer and

the authorised dealer to issue Instructions when selling

implements and to instruct customers in the use with refer-

ence to the safety, operating and maintenance regulations.

Confirmation in the form of a declaration of transfer is

required to verify that the implement and Instructions have

been transferred correctly. The declaration of transfer was

attached to the implement on delivery.

Every self-employed person and farmer is an entrepreneur

within the meaning of the product liability legislation. In

accordance with the laws of product liability, entrepre-

neurial property damages are excluded from the liability.

All damage to property within the meaning of the product

liability legislation is regarded as damage caused by the

implement but not to the implement.

These Operating Instructions are integral part of the imple-

ment delivery scope. You should therefore hand them over to

the new owner if ownership of the implement is transferred.

Train and instruct the new owner in the regulations stated.

The Pöttinger Service-Team wishes you good luck.

- 7 -

2000_GB-Warning signs_3751

EN

Warning SignS

Meaning of warning signs

1

(2x)

Shut engine off and remove key before carrying out any

maintenance or repair work.

495.165.0001

2

(2x)

Do not stand in the machine's swivel range.

495.166

3

(2x)

Never reach into the crushing danger area as long as parts can

move there.

495.171

4

(2x)

Do not touch rotating machine parts. Wait until moving machine

parts come to a standstill.

Keep a safe distance from the mowing blades when the engine

is running and the PTO shaft is connected.

Close both side protective coverings before engaging p.t.o.

Keep a safe distance as danger exists through parts being ejected

while motor is running.

495.175.0001

5

(2x)

Before entering the danger area, put on a seat belt.

495.169

6

(2x)

Suspension point for unloading

495.404

- 8 -

2000_GB-Warning signs_3751

EN

Warning signs

7

(1x)

Set the hydraulic control unit to float position during operation.

495.469

8

(1x)

Product liability

495.713

9

(1x)

Blade changing

495.725

10

(1x)

434.960 434.961

434.969.999 434.970.999

495.855/19

Blade equipment

495.855

11

(1x)

690 mm

495.665.0003/18

Attachment height - Master

495.665.0003

Attachment height - Pro

495.XXX.xxxx

- 9 -

2000_GB-Warning signs_3751

EN

Warning signs

12

(1x)

Please read the operating instructions before initial operation!

494.529.0003

Position of the warning signs

7

11

9

10

2

4

6

3

5

2

5

4

3

8

1

6

1

12

068-19-011

- 10 -

2000-GB AttAchment_3751

EN

2. Lifting gear with cross piece

When using lifting gear with a crosspiece (Q) between

the lower links, damage could occur to the cardan shaft

when lowering the attached machine.

To avoid damage, an extension must be installed

between the lifting gear and the attachment frame.

In such a case, please contact our Customer Service

Dept.

3. PTO shafts are very far forward

On tractors where the PTO shaft stub is very far forward,

the PTO shaft would have to be considerably shortened.

•Whenthemachineisraised,thereisinsufficientcasing

to over the cardan shaft.

Safety advice

CAUTION

Risk of slight or moderate injury through tractor's

double-acting front lifting gear.

• Do not exceed the maximum lowering depth

of the mower unit! This results in unaccept-

ably high pressure on the limiting chains,

which can break. In the most unpleasant

case, this will result in injuries to persons in

the danger area around the mower.

Attaching in general

1. Observe safety tips in supplement A.

2. Attach the machine to the tractor's front lifting gear.

3. Secure locking bolts with linch pins.

Cardan shaft

The cardan shaft is to be checked before first use and

adapted if necessary (see Chapter "Adapting the Cardan

Shaft" in Supplement B).

#

Attaching problems

1. No front hydraulic connection:

If the tractor has no hydraulic connection at the front,

then a hydraulic hose must be run from the rear to the

front.

A three-way tap for switching between the front lifting gear

(HW) and front control device (SG) may be necessary

with some tractors.

HW

SG

attaching to tractor

- 11 -

2000-GB AttAchment_3751

AttAching to trActor EN

• Themaximumuniversal-jointangleofdeviationwill

possibly be exceeded (see Supplement B also).

In this case, an accessory kit is necessary which

positions the machine approx. 200 mm forward.

In such a case, please contact our Customer Service

Dept.

Mudguards and protective cloths

DANGER

Life-threatening danger through rotating or ejected

components

• Before starting work, check the protective

devices for function, correct position and

condition.

• Fold the guards down before starting work.

• Replace defective protective devices imme-

diately.

• The manufacturer takes no responsibility

for any manipulation or improper use of the

safety devices.

• Do not access the protective device as this

will damage it.

DANGER

Life-threatening danger through rotating or ejected

components

• Switch off the cutter bar drive.

• Wait for the cutter bars to come to a stand-

still before swivelling the mudguards and

protective cloths up.

Mudguards and protective cloths must be folded down

before switching on the machine (= brought into working

position).

For maintenance work or when parking, the mudguards

and protective cloths can be raised.

Lift-up

1. Loosen locking mechanism (1) and swivel protection

(2) up.

1

2

2. Engage frame guard in holder (3)

3

Hydraulic side guards

CAUTION

Risk of slight or moderate injury through being

crushed by the side guards.

• Pay special attention when swivelling the

side guards.

• Do not reach into the danger area.

• Direct other persons away from the hazard

area.

As an option, the side guards can be swivelled hydraulically

with the control valve on the tractor.

This would eliminate the necessity of releasing or latching

a locking device.

Transport position

When both side guard elements (2) are swivelled up and

locked into the holder (3), the following transport width

results:

Type NC 261 NC 301 NC 351

Transport width (X) < 2.58m < 3.00m < 3.42m

- 12 -

2000-GB Att

A

2000-GB AttA2000-GB Att

chment_3751

Att

A

AttAAtt

ching to tr

A

ching to trAching to tr

ctor

EN

Road Transport

• Observe

the

statutory

regulations

for

your

country.

Attachment C contains information on attaching lighting,

valid for Germany.

• Travelling

on

public

roads

may

only

be

carried

out

as

described in the Chapter "Transport position".

• Secure

the

hydraulic

lower

link,

so

that

machine

cannot

swing out sideways.

Top linkage

TIP

Use a rigid upper link.

Parking the machine

Always park mower units with conditioner on stand (30),

otherwise danger of tipping over exists!

- Fix support leg using locking pin

30

TIP

A mowing unit with swath former does not require support

stands for secure parking.

NOTE

Material damage may occur when parking the

machine through the cardan shaft and attaching

frame colliding.

•

Pay attention to the attachment height indi

-

cator. The optimum attachment height must

be observed. For this purpose, the display

arrow must not move above the marking.

•

- 13 -

1801_GB-AlphaMotion_3751

EN

Transport position

-

The mower must always be locked during transportation.

-

Swivel flap (F) to "Pos. 1"

K

Pos 1

-

Close stopcock (Pos.

A)

Pos.

E

Pos.

A

Mounting

-.

Mount the Expander (EX) in the correct position.

Position A

-

before coupling to the tractor

A

EX

Position B

-

after coupling to the tractor and during mowing

B

General safety information

NOTE

Risk of material damage due to collisions between

the mower and its surroundings.

•

Lock the mower before transport.

WARNING

Risk of serious injury or injury resulting in death due

to the machine tipping over.

•

Park the implement on ﬂat, solid ground.

CAUTION

Risk of slight or moderate injury through tractor's

double-acting front lifting gear.

•

Do not exceed the maximum lowering depth

of the mower unit! This results in unaccept

-

ably high pressure on the limiting chains,

which can break. In the most unpleasant

case, this will result in injuries to persons in

the danger area around the mower.

Parking position

-

Swivel the flap (K) upwards to park the mower unit (Pos

0).

K

Pos 0

A

-

Close stopcock (Pos.

A)

Pos.

E

Pos.

A

TIP

It is only possible to remove a Conditioner if flap (F) is

in position 0.

M

OUNTING

U

NIT "

UNIT "U

alpha motion

NIT "alpha motionNIT "

"

- 14 -

1801_GB-AlphaMotion_3751

EN

MOUNTING UNIT "alpha motion"

K

Pos 2

- Set working height at 1370 mm and secure with limiting

chain (7). Only with Alphamotion.

(The limiting chains (3) serve as setting aids!)

- Set lower link height at approx. 690 mm.

690 mm

495.665.0003/18

- Connect cardan shaft.

- Bring cardan shaft holder into park position

- Couple the hydraulic lines for lifting cylinder on the

single-acting (SA) hydraulic circle of the tractor.

EW

T

P

T

021-06-04

- Open shut-off valve (pos. E)

-Raise the mounting frame (MF) via the tractor’s lifting gear

Pos. E

Pos.

A

- Fold the flap (F) towards the front (Pos.2).

- 15 -

1801_GB-AlphaMotion_3751

EN

MOUNTING UNIT "alpha motion"

Set spring tension

E = Relieving spring

R = Weight counterbalance: right

L = Weight counterbalance: left

Cutter unit with swather(guide values)

Type E R L

(mm) (mm) (mm)

NOVACAT 261 245 55 25

NOVACAT 301 270 25 60

NOVACAT 351 250 25 90

NOVACAT 261 MASTER 215 40 85

NOVACAT 301 MASTER 180 70 85

NOVACAT 351 MASTER 205 40 85

Cutter unit with Conditioner ED (guide values)

Type E R L

(mm) (mm) (mm)

NOVACAT 261 180 45 45

NOVACAT 301 205 45 45

NOVACAT 351 185 25 25

Cutter unit with Conditioner RC (guide values)

Type E R L

(mm) (mm) (mm)

NOVACAT 301 160 45 45

NOVACAT 351 210 25 25

- The ground bearing load of the cutter bar is more

important than the standard length values for the

springs. It should be approx. 150 kg (approx. 75 kg

left and right).

75 kg

TD 71-98-05

TIP

• Lock the hydraulic valve of the front lifting

gear during operation and transport.

- 16 -

2000-EN Applic

A

tio

AtioA

N

_3751

EN

Starting

W

ork

WorkW

A transfer, located near the gearing, advises which p.t.o.

speed your mower unit is equipped for.

• Always

and

only

switch

the

p.t.o.

drive

on

when

all

safety devices (covers, protective clothes, casings) are

in proper condition and are attached to the implement

in their safety positions.

-

Hook up expander (EX)

EX

3.

Pay attention to correct

p.t.o. direction of rotation!

TD8/95/6a

4.

Prevent any damage!

The area to be mowed must be free of obstacles

or foreign objects. Such objects (e.g. large

stones, pieces of wood, boundary stones,

etc.) can damage the mower unit.

If, nevertheless, a collision occurs,

• Stop

immediately

and

switch

off

the

drive.

• Check

the

implement

carefully

for

any

damage

In

particular check the mowing discs and their drive shafts

(4a).

• If

necessary

have

it

checked

over

in

a

specialist

work

shop as well.

Safety advice

DANGER

Life-threatening- by blades thrown away

•

After the ﬁrst operating hours tighten all

blade screwed connections

•

Check all safety equipment before starting

work. In particular, make sure that the side

safeguards are folded down correctly in the

ﬁeld transport position.

DANGER

Life-threatening danger exists through ejected

parts when removing clogging, changing blades or

adjusting the machine.

•

Stop tractor/trailer unit on level ground and

apply tractor's brakes.

•

Park the mower in working position.

•

Before going back to the machine, make

sure that the pto has stopped and the hy

-

draulic hoses are depressurised.

•

Remove the tractor key!

DANGER

Life-threatening danger exists through falling off

the machine.

•

Do not climb onto the machine, or play on or

around it.

•

Do let anybody to climb onto the machine,

or play on or around it.

•

Before starting, make sure that no one is

standing on the machine or inits danger

area!

TIP

Further safety instructions: see Supplement A, pt. 1. - 7.)

Important notes prior to starting work

1.

Check

-

Check condition of blades and blade holder.

-

Check mowing discs for damage (see chapter

"Maintenance and Service")

2.

Switch machine on only when in working

position and do not exceed the specified p.t.o.

speed (e.g. max. 540 rpm)!

- 17 -

2000-EN ApplicAtioN_3751

EN

Starting work

Set cutting height1)

With upper link (O):

Altering the upper link length (L +/-) enables a cutting height

difference of between 3 to 6 cm.

TIP

When parking the mower, return the attached triangle

to the vertical position to ensure easy removal from the

quick coupler.

With high-cut skids:

Use when cutting height exceeds 6 cm.

Mowing

DANGER

Danger to life due to parts being thrown off.

• Before starting to work, check all guards to

ensure that they are in the correct posi-

tion and secured. Also check whether the

protective devices have defects which impair

their function.

• Stones and other objects can be picked up

and ejected when mowing. Direct all per-

sons out of the danger area.

1. Set cutting height by turning upper link spindle

(max. 5° incline for mower discs)

2. For mowing, slowly engage the p.t.o. shaft

away from the crop and bring the mower rotor

up to full speed.

Smoothly increasing the p.t.o. speed will avoid system-

related noises from the p.t.o. freewheel.

- The driving speed depends on the ground conditions

and the crop to be mown.

only for disc mowing

After contact with a foreign object

• Checktheconditionofknivesandtheknifefixings.

• Retightenallknifescrewfittings.

• Checktheimplement carefullyforanydamage.The

mowing discs and their drive shaft must be checked in

particular.

• Ifnecessaryhaveitcheckedoverintheworkshopas

well.

5. Keep away from the engine when it's running.

• Guidepeopleoutofthedangerareaastheymayreceive

injuries from foreign objects being ejected by the mower.

Special care is necessary on stony ground and near

roads and paths.

bsb 447 410

6. Wear hearing protection

The noise level in the workplace can deviate from the

measured value (see Technical Data) partly because of

the differing cabin types of various tractors.

• Ifanoiselevelof85dB(A)isreachedorexceeded,

the farmer must have suitable hearing protection in

readiness (UVV 1.1 §2).

• Ifanoiselevelof90dB(A)isreachedorexceeded,

the hearing protection must be worn (UVV 1.1 § 16).

- 18 -

2000-EN ApplicAtioN_3751

EN

Starting work

Reversing

Raise the mower when reversing!

Overview and Function

A narrow swath is formed when using the swath plates while mowing. This avoids driving over the crop with wide tractor tyres.

1

2

3

Designations:

(1) Swath disc (2) Swath disc holder

(3) Adjusting mechanism

Possible settings

DANGER

Danger to life - long hair or wide robes drawn in by

rotating components

• Shut engine off and remove key before car-

rying out maintenance or repair work.

• Switch off the motor before opening or

removing guards.

• Long hair should be tied together

• Wear gloves and tight work clothes.

Working area:

The working range of the swath former can be adjusted

via the slotted holes (1).

1

Optimal setting

The discs are mounted 0-10 mm lower than the bottom

edge of the cutter bar.

- 19 -

1800-GB_Tine condiTioner_3751

EN

SWath former

Maintenance

DANGER

Danger to life - long hair or wide robes drawn in by

rotating components

• Shut engine off and remove key before car-

rying out maintenance or repair work.

• Switch off the motor before opening or

removing guards.

• Long hair should be tied together

• Wear gloves and tight work clothes.

The swath former is maintenance-free with the exception

of cleaning activities.

Removal and installation of the swath

former

A tine conditioner, roller conditioner or swath former can

be mounted on the mower unit. Depending on which unit is

built, special work steps are necessary during the change.

For details see the Section “REPLACE CONDITIONER”

Optional Equipment

Additional swath disc

Setting both tension springs:

A = for high, dense feed quantities.

B = basic setting.

C = for short forage.

Conveying cone

Conveying cones are recommended:

- to improve the conveyance rate of swath deposits,

particularly with heavy, dense forage.

- See spare parts list for individual parts

- 20 -

1800-GB_Tine condiTioner_3751

swath former EN

La pagina si sta caricando...

Pottinger NOVACAT 301 ALPHA MOTION RC Istruzioni per l'uso

Pottinger NOVACAT 301 ALPHA MOTION RC Istruzioni per l'uso

in altre lingue

Documenti correlati

Altri documenti