Pioneer AVIC-D3 Manuale utente

MANUEL D’INSTALLATION

INSTALLATION MANUAL

AVIC-D3

This product conforms to new cord colours.

Los colores de los cables de este producto se confor-

man con un nuevo código de colores.

Dieses Produkt entspricht den neuen kabelfarben.

Le code de couleur des câbles utilisé pour ce produit est

nouveau.

Questo prodotto è conforme ai nuovi codici colori.

De kleuren van de snoeren van dit toestel zijn gewijzigd.

English

Español

Deutsch

Français

Italiano

Nederlands

1

IMPORTANT INFORMATION

ABOUT YOUR NEW NAVIGATION SYSTEM AND THIS MANUAL

• The navigation features of this product (and rear view camera option if pur-

chased) are intended solely to aid you in the operation of your vehicle. It is not a

substitute for your attentiveness, judgement and care when driving.

• Never use this navigation system to route to hospitals, police stations, or similar

facilities in an emergency. Please call the appropriate emergency number.

• Do not operate this navigation system (or the rear view camera option if pur-

chased) if doing so in any way will divert your attention from the safe operation

of your vehicle. Traffic restrictions and advisories currently in force should

always take precedence over guidance given by this product. Always obey current

traffic restrictions, even if this product provides contrary advice.

• This manual explains how to install this navigation system in your vehicle.

Operation of this navigation system is explained in the separate Operation

Manual for the navigation system.

• Do not install this product where it may (i) obstruct the driver’s vision, (ii) impair

the performance of any of the vehicle’s operating systems of safety features,

including airbags, hazard lamp buttons or (iii) impair the driver’s ability to safely

operate the vehicle. In some cases, it may not be possible to install this product

because of the vehicle type or the shape of the vehicle interior.

English
Español
Deutsch
Français
Italiano
Nederlands
IMPORTANT INFORMATION .................... 1
ABOUT YOUR NEW NAVIGATION 
SYSTEM AND THIS MANUAL .............. 1
IMPORTANT SAFEGUARDS  .................... 3
PLEASE READ ALL OF THESE INSTRUC-
TIONS REGARDING YOUR NAVIGA-
TION SYSTEM AND RETAIN THEM 
FOR FUTURE REFERENCE .................... 3
Connecting the System  ............................ 4
-
Before installing this product
-
To prevent damage
-
Parts supplied
Connecting the system  ...................................... 7
Connecting the power cord (1) .......................... 9
Connecting the power cord (2) ........................ 11
When connecting to separately sold power 
amp .......................................................... 13
When connecting a rear view camera  ............ 15
When connecting the external video 
component ................................................ 16
-
When using the AV-1 Input
-
When using the AV-2 Input
When connecting the external unit featuring 
video source  ............................................ 17
When connecting the rear display  .................. 17
-
When using a rear display connected to 
rear video output
Installation ................................................ 18
To guard against electromagnetic interference
.................................................................. 19
Before installing  .............................................. 19
Installing this navigation system  .................... 20
-
Installation notes
-
Parts supplied
-
Before installing this navigation unit
-
Installation with the holder and side bracket
-
Installation using the screw holes on the side
of the navigation unit
Installing the GPS aerial .................................. 24
-
Installation notes
-
Parts supplied
-
When installing the aerial inside the vehicle
(on the rear shelf)
-
When installing the aerial outside the vehicle
(on the body)
After Installing this Navigation System
.............................................................. 27
2
Contents

IMPORTANT SAFEGUARDS

3

PLEASE READ ALL OF THESE INSTRUCTIONS REGARDING YOUR

NAVIGATION SYSTEM AND RETAIN THEM FOR FUTURE REFERENCE

1. Read this manual fully and carefully before installing your navigation system.

2. Keep this manual handy for future reference.

3. Pay close attention to all warnings in this manual and follow the instructions care-

fully.

4. This navigation system may in certain circumstances display erroneous informa-

tion regarding the position of your vehicle, the distance of objects shown on the

screen, and compass directions. In addition, the system has certain limitations,

including the inability to identify one-way streets, temporary traffic restrictions

and potentially unsafe driving areas. Please exercise your own judgement in the

light of actual driving conditions.

5. As with any accessory in your vehicle’s interior, the navigation system should not

divert your attention from the safe operation of your vehicle. If you experience

difficulty in operating the system or reading the display, please make adjustments

while safely parked.

6. Please remember to wear your seat belt at all times while operating your vehicle.

If you are ever in an accident, your injuries can be considerably more severe if

your seat belt is not properly fastened.

7. In certain countries, laws may restrict the placement and use of navigation sys-

tems in your vehicle. Please comply with all applicable laws and regulations in

the installation and operation of your navigation system.

Do not attempt to install or service your navigation system by yourself.

Installation or servicing of the navigation system by persons without training and

experience in electronic equipment and automotive accessories may be dangerous

and could expose you to the risk of electric shock or other hazards.

English

Español

Deutsch

Français

Italiano

Nederlands

4

Connecting the System

• Pioneer does not recommend that you install your navigation system yourself. We

recommend that only authorised Pioneer service personnel, who have special train-

ing and experience in mobile electronics, set up and install this product. NEVER

SERVICE THIS PRODUCT YOURSELF. Installing or servicing this product and

its connecting cables may expose you to the risk of electric shock or other hazards,

and can cause damage to the navigation system that is not covered by warranty.

• If you decide to perform the installation yourself, and have special training and

experience in the mobile electronics installations, please carefully follow all of the

steps in the Installation Manual.

• Secure all wiring with cable clamps or electrical tape. Do not allow any bare wiring

to remain exposed.

• Do not directly connect the yellow lead of this product to the vehicle battery. If the

lead is directly connected to the battery, engine vibration may eventually cause the

insulation to fail at the point where the wire passes from the passenger compart-

ment into the engine compartment. If the yellow lead’s insulation tears as a result

of contact with metal parts, short-circuiting can occur, resulting in considerable

danger.

• It is extremely dangerous to allow the GPS aerial cable or microphone cable to

become wound around the steering column or gearstick. Be sure to install this

product, its cables, and wiring away in such a way that they will not obstruct or

hinder driving.

• Make sure that the cables and wires are routed and secured so they will not inter-

fere with or become caught in any of the vehicle’s moving parts, especially the

steering wheel, gearstick, handbrake, sliding seat tracks, doors, or any of the vehi-

cle’s controls.

• Do not route wires where they will be exposed to high temperatures. If the insula-

tion heats up, wires may become damaged, resulting in a short circuit or malfunc-

tion and permanent damage to the product.

• Do not cut the GPS aerial cable to shorten it or use an extension to make it longer.

Altering the aerial cable could result in a short circuit or malfunction.

• Do not shorten any leads. If you do, the protection circuit (fuse holder, fuse resister

or filter, etc.) may fail to work properly.

• Never feed power to other electronic products by cutting the insulation of the

power supply lead of the navigation system and tapping into the lead. The current

capacity of the lead will be exceeded, causing overheating.

• The black lead is earth. Please earth this lead separately from the earth of high-

current products such as power amps. Do not earth more than one product togeth-

er with the earth from another product. For example, you must separately earth

any amplifier unit away from the earth of this navigation system. Connecting

earths together can cause a fire and/or damage the products if their earths became

detached.

5

Connecting the System

Before installing this product

• This product is for vehicles with a 12-volt battery and negative earthing. Check the bat-

tery voltage of your vehicle before installation.

To prevent damage

When replacing the fuse, be sure to only use a fuse of the rating prescribed on this

product.

• When disconnecting a connector, pull the connector itself. Do not pull the lead, as you

may pull it out of the connector.

• This product cannot be installed in a vehicle that does not have an ACC (accessory)

position on the ignition switch.

• To avoid short-circuiting, cover the disconnected lead with insulating tape. It is especial-

ly important to insulate all unused speaker leads, which if left uncovered may cause a

short circuit.

• Attach the connectors of the same colour to the corresponding coloured port, i.e., blue

connector to the blue port, black to black, etc.

• Refer to the owner’s manual for details on connecting the power amp and other units,

then make connections accordingly.

• Since a unique BPTL circuit is employed, do not directly earth the ≠ side of the speaker

lead or connect the ≠ sides of the speaker leads together. Be sure to connect the ≠ side

of the speaker lead to the ≠ side of the speaker lead on this navigation system.

• If the RCA pin jack on this product will not be used, do not remove the caps attached to

the end of the connector.

• Never connect speakers with an output rating of less than 50 W channel or impedance

outside of the 4 ohms to 8 ohms specifications to your navigation system. Connecting

speakers with output and/or impedance values other than those noted here may result in

the speakers catching fire, emitting smoke, or becoming damaged.

• When the “ANT CTRL” mode is set to “Tuner”, the vehicle’s aerial can be stowed or

turned off by following the instructions below.

– Change the source from radio (MW/LW or FM) to another source

– Turn the source off

– Turn off the ignition switch (ACC OFF)

• If the “ANT CTRL” mode is set to “Power”, the vehicle’s aerial can be stowed or turned

off only when the ignition switch is turned off (ACC OFF).

No ACC positionACC position

O

N

S

T

A

R

T

O

F

A

C

O

N

S

T

A

R

T

O

F

• To avoid shorts in the electrical sys-

tem, be sure to disconnect the (–)

battery cable before beginning

installation.

English

Español

Deutsch

Français

Italiano

Nederlands

6

• When the ignition switch is turned on (ACC ON), a control signal is output through the

blue/white lead. Connect to an external power amp’s system remote control terminal

(max. 300 mA 12 V DC). The control signal is output through the blue/white lead, even

if the audio source is switched off.

• When an external power amp is being used with this system, be sure not to connect the

blue lead to the amp’s power terminal. Likewise, do not connect the blue lead to the

power terminal of the auto aerial. Such connection could cause excessive current drain

and malfunction as well as damage to the auto aerial of the vehicle.

Parts supplied

RCA connector

GPS aerial

Extension lead

(for speed signal)

Extension lead

(for reverse signal)

ConnectorPower cordThe navigation unit

7

Connecting the System

Connecting the system

Aerial

jack

Vehicle

aerial

Light grey

5 m

GPS aerial

WIRED REMOTE INPUT

Please see the Instruction

Manual for the Wired Remote

Control Adapters (sold separately).

DIGITAL OUT*

EXTENSION port

Not used.

Dock

connector

port

Interface cable for iPod

®

(sold separately)

iPod

®

with

Dock Connector

The navigation unit

Blue

10

• To avoid the risk of accident and the potential violation of applicable laws, this product

should never be used while the vehicle is being driven except for navigation purposes. And,

also Rear Displays should not be in a location where it is a visible distraction to the driver.

• In some countries, the viewing of images on a display inside a vehicle even by persons other

than the driver may be illegal. Where such regulations apply they must be obeyed and this

product’s video source should not be used.

*: This terminal is intended to support future

equipment and should not be used if you

are using this product by itself.

8

English

Español

Deutsch

Français

Italiano

Nederlands

Bluetooth

adapter

(CD-BTB200)

(sold separately)

Blue

Black

Microphone

(supplied with

Bluetooth adapter)

IP-BUS cable

(sold separately)

Multi-CD player

(sold separately)

9

Connecting the System

Connecting the power cord (1)

Connect leads of the same

colour to each other.

Cap (*1)

When not using this terminal,

do not remove the cap.

ISO connector

*1

*2

*4

*3

*5

Yellow (*2)

To terminal always supplied

with power regardless of

ignition switch position.

Red (*4)

To electric terminal controlled

by ignition switch (12 V DC)

ON/OFF.

Yellow (*3)

Back-up

(or accessory)

Red (*5)

Accessory

(or back-up)

Black (earth)

To vehicle (metal) body.

Orange/white

To lighting switch terminal.

Note:

In some vehicles, the ISO connector

may be divided into two. In this case,

be sure to connect to both connectors.

Note:

Depending on the kind of vehicle, the

function of *3 and *5 may be different.

In this case, be sure to connect *2 to *5

and *4 to *3.

Speaker leads

White: Front left +

White/black: Front left ≠

Grey: Front right +

Grey/black: Front right ≠

Green: Rear left + or Subwoofer + (*9)

Green/black: Rear left ≠ or Subwoofer ≠ (*9)

Violet: Rear right + or Subwoofer + (*9)

Violet/black: Rear right ≠ or Subwoofer ≠ (*9)

Yellow/black

If the vehicle can send a mute signal to this terminal,

the mute function can be activated on this navigation

system when the terminal is connected to *8.

Notes:

• When a subwoofer (*9) is connected to this navigation

system instead of a rear speaker, change the rear output

setting in the Initial Setting. (Refer to the Operation

Manual.) The subwoofer output of this navigation sys-

tem is monaural.

• When using a subwoofer of 70W (2Ω), be sure to con-

nect with violet and violet/black leads of this naviga-

tion system. Do not connect anything with Green and

Green/Black leads.

10

English

Español

Deutsch

Français

Italiano

Nederlands

(*8)

Blue (*7)

To Auto-aerial relay control terminal

(max. 300 mA 12 V DC).

The pin position of the ISO connector will differ

depending on the type of vehicle. Connect *6 and

*7 when Pin 5 is an aerial control type. In

other types of vehicle, never connect *6 and

*7.

Blue (*6)

FUSE (10A)

10

The navigation unit

Yellow/black

If you use an equipment with mute function, connect that equipment to the

Audio Mute lead. If not, keep the Audio Mute lead free of any connections.

Power cord

Note:

Audio source will be set to mute or attenuate, while the following sounds

will not be muted or attenuated. For details, see the Operation Manual.

- voice guidance of the navigation

- incoming ringtone and incoming voice of the mobile phone that is

connected to this navigation system via Bluetooth wireless technology

Note:

The aerial will automatically retract, yet the timing

varies depending on the setting. (Refer to page 5.)

For more detailed information on changing the “ANT

CTRL” mode, refer to “Switching the auto aerial

setting” in the Operation Manual.

RCA connector

26 cm

10

Note:

Cords for this navigation system and those

for other products may be different colours

even if they have the same function. When

connecting this navigation system to

another product, refer to the supplied man-

uals of both products and connect cords

that have the same function.

When replacing the fuse, be sure to only use a

fuse of the rating prescribed on this product.

For information on other leads

☞

See Page 11.

Pink (CAR SPEED SIGNAL INPUT)

The mobile navigation system is connected here to detect the distance

the vehicle travels. Always connect the vehicle’s speed detection

circuit or the ND-PG1 speed pulse generator, sold separately. Failure

to make this connection will increase errors in the location display.

IMPROPER CONNECTION MAY RESULT IN SERIOUS

DAMAGE OR INJURY INCLUDING ELECTRICAL SHOCK,

AND INTERFERENCE WITH THE OPERATION OF THE

VEHICLE’S ANTILOCK BRAKING SYSTEM, AUTOMATIC

GEARBOX AND SPEEDOMETER INDICATION.

LIGHT GREEN LEAD AT POWER

CONNECTOR IS DESIGNED TO DETECT

PARKED STATUS AND MUST BE

CONNECTED TO THE POWER SUPPLY SIDE

OF THE HANDBRAKE SWITCH. IMPROPER

CONNECTION OR USE OF THIS LEAD MAY

VIOLATE APPLICABLE LAW AND MAY

RESULT IN SERIOUS INJURY OR DAMAGE.

Light green

Used to detect the ON/OFF status of the handbrake. This lead must be

connected to the power supply side of the handbrake switch.

If this connection is made incorrectly or omitted, certain

functions of your navigation system will be unusable.

• It is strongly suggested that the speed pulse wire be connected

for accuracy of navigation and better performance of interlock.

• If the speed pulse wire is unavailable for some reason, it is

recommended that the pulse generator (ND-PG1) be used.

Note:

The position of the speed detection circuit and the position of the

parking brake switch vary depending on the vehicle model. For

details, consult your authorised Pioneer dealer or an installation

professional.

11

Connecting the System

Connecting the power cord (2)

Connection method

Clamp the parking brake

switch power supply side lead.

Clamp firmly with

needle-nosed pliers.

Power supply side

Earth side

Handbrake switch

Speed detection circuit lead

Vehicle injection

computer

Connector

Pass the extension cord

and the lead for the

speed detection circuit

through this hole.

Clamp firmly

with needle-

nosed pliers.

Close the cover.

Connection method

10

Power cord

Be sure to use only the supplied extension lead. Use of another lead

could cause fire, smoke and/or damage this navigation system.

12

English

Español

Deutsch

Français

Italiano

Nederlands

Note:

Cords for this navigation system and those for other

products may be different colors even if they have

the same function. When connecting this navigation

system to another product, refer to the supplied

manuals of both products and connect cords that

have the same function.

Violet/white (REVERSEGEAR SIGNAL INPUT)

This is connected so that the navigation system can

detect whether the vehicle is moving forwards or

backwards. Connect the violet/white lead to the

lead whose voltage changes when the reverse gear

is engaged. Unless connected, the sensor may not

detect your vehicle travelling forward/backward

properly, and thus the position of your vehicle

detected by the sensor may be misaligned from the

actual position.

Connection method

Clamp the reversing lamp lead.

Clamp firmly with

needle-nosed pliers.

Reversing

lamp lead

Fuse resistor

Check the position of your vehicle’s

reversing lamp (the one that lights

up when the gearstick is in reverse

[R]) and find the reversing lamp lead

in the boot.

The navigation unit

Extension lead

(for reverse signal)

Extension lead (for speed signal)

5 m

Note:

When you use the ND-PG1 speed pulse

generator (sold separately), please make sure

to connect this lead.

When you use a rear view camera, please

make sure to connect this lead. Otherwise you

cannot switch to rear view camera picture.

☞

See Page 15.

5 m

For information on other leads

☞

See Page 9.

13

Connecting the System

The navigation unit

Front output

(FRONT OUTPUT)

Subwoofer output

or non-fading output

(SUBWOOFER OUTPUT or

NON-FADING OUTPUT)

Rear output

(REAR OUTPUT)

28 cm

Blue/white

30 cm

To system control terminal of the power amp

(max. 300 mA 12 V DC).

Do not connect this lead to Auto-aerial control

terminal.

30 cm

RCA connector

10

When connecting to separately sold power amp

14

English

Español

Deutsch

Français

Italiano

Nederlands

Power amp

(sold separately)

Power amp

(sold separately)

Power amp

(sold separately)

+

≠

+

≠

+

≠

+

≠

+

≠

+

≠

System remote control

RCA cables

(sold separately)

Front speaker

Rear speaker

Subwoofer

Front speaker

Rear speaker

Subwoofer

Left Right

Perform these connections when using

the optional amplifier.

Note:

You can change the RCA output of the subwoofer depending on your subwoofer

system. (Refer to the Operation Manual.)

15

Connecting the System

When connecting a rear view camera

When using this product with a rear view camera, automatic switching to video from a rear

view camera is possible when the gear shift is moved to REVERSE (R) position.

Rear view mode also allows you to check what is behind you while driving.

USE INPUT ONLY FOR REVERSE OR MIRROR IMAGE REAR VIEW CAMERA. OTHER USE

MAY RESULT IN INJURY OR DAMAGE.

• The screen image may appear reversed.

• The rear view camera function is to use this product as an aid to keep an eye on trailers, or backing

into a tight parking spot. Do not use this function for entertainment purposes.

• The object in rear view may appear closer or more distant than in reality.

• Please note that the edges of the rear view camera images may differ slightly according to whether

full screen images are displayed when backing, and whether the images are used for checking the

rear when the vehicle is moving forward.

15 cm

Extension lead (for reverse signal)

5 m

Violet/white RCA connector

Power cord

Rear view

camera

RCA cable

(sold separately)

To video output

Connect to the rear view camera. Do not connect

to any other equipment.

Note:

The navigation unit

Fuse resistor

Brown

(REAR VIEW CAMERA IN)

Note:

It is necessary to set to “Camera” in

“System” when connecting the rear

view camera. (For details, see the

Operation Manual.)

Be sure to use only the supplied extension lead.

Use of another lead could cause fire, smoke

and/or damage this navigation system.

About connection method

10

☞

See Page 11.

When connecting the external video component

When using the AV-1 Input

• It is necessary to set “AV-1 Input” in “System” to “Video” when connecting the exter-

nal video component. (For details, refer to the Operation Manual.)

When using the AV-2 Input

• It is necessary to set “AV-2 Input” in “System” to “Video” when connecting the exter-

nal video component. (For details, refer to the Operation Manual.)

Be sure to use a CD-RM10 (sold separately) for wiring. If you use other cables, there is a case where

wiring position differs, images and sounds may be disturbed.

L: Left audio (white)

R: Right audio (Red)

V: Video (Yellow)

G: Ground

OK

G

V

R

L

G

R

V

L

The navigation unit

RCA cables

(sold separately)

To audio outputs

Yellow

Red, white

External

component

(sold separately)

video

To video output

CD-RM10

(sold separately)

Mini jack

To audio outputs

Yellow

(VIDEO INPUT)

20 cm

RCA connector

Red, white

(AUDIO INPUT)

RCA cables

(sold separately)

To video output

10

The navigation unit

External

component

(sold separately)

video

16

English

Español

Deutsch

Français

Italiano

Nederlands

17

Connecting the System

When connecting the external unit featuring video source

• It is necessary to set “AV-1 Input” in “System” to “EXT” when connecting the external

video component. (For details, refer to the Operation Manual.)

When connecting the rear display

When using a rear display connected to rear video output

NEVER install the rear display in a location that enables the driver to watch the

video source while driving.

This navigation system’s rear video output is for connection of a display to enable passen-

gers in the rear seats to watch the video source.

10

The navigation unit

RCA

RCA connector

15 cm

cables

(sold separately)

Tovideoinput

Yellow

(REAR

MONITOR

OUTPUT)

Rear display with

RCA input jacks

The navigation unit

Blue

10

RCA cable

(sold separately)

To IP-BUS output

IP-BUS cable (sold separately)

20 cm

Yellow

(VIDEO INPUT)

Pioneer external unit

(sold separately)

To video output

Black

RCA connector

Installation

• Pioneer does not recommend that you install or service your navigation sys-

tem yourself. Installing or servicing the product may expose you to risk of

electric shock or other hazards. Refer all installation and servicing of your

navigation system to authorised Pioneer service personnel.

• Never install this product in places where, or in a manner that:

* It could injure the driver or passengers if the vehicle stops suddenly.

* It may interfere with the driver’s operation of the vehicle, such as on the

floor in front of the driver’s seat, or close to the steering wheel or gear-

stick.

• Make sure there is nothing behind the dashboard or panelling when drilling

holes in them. Be careful not to damage fuel lines, brake lines, electronic

components, communication wires or power cables.

• When using screws, do not allow them to come into contact with any electri-

cal lead. Vibration may damage wires or insulation, leading to a short circuit

or other damage to the vehicle.

• To ensure proper installation, use the supplied parts in the manner specified.

If any parts other than the supplied ones are used, they may damage internal

parts of this product or they may work loose and the product may become

detached.

• It is extremely dangerous to allow the GPS aerial lead or microphone lead to

become wound around the steering column or gearstick. Be sure to install

this product in such a way that it will not obstruct driving.

• Make sure that leads cannot get caught in a door or the sliding mechanism of

a seat, resulting in a short circuit.

• Please confirm the proper function of your vehicle’s other equipment follow-

ing installation of the navigation system.

• Certain government laws may prohibit or restrict the placement and use of

this system in your vehicle. Please comply with all applicable laws and regu-

lations regarding the use, installation and operation of your navigation sys-

tem.

18

English

Español

Deutsch

Français

Italiano

Nederlands

19

Installation

• Do not install this navigation system where it may (i) obstruct the driver’s

vision, (ii) impair the performance of any of the vehicle’s operating systems

or safety features, including airbags, hazard lamp buttons or (iii) impair the

driver’s ability to safely operate the vehicle.

• Install the navigation system between the driver’s seat and front passenger

seat so that it will not be hit by the driver or passenger if the vehicle stops

quickly.

• Never install the navigation system in front of or next to the place in the

dash, door, or pillar from which one of your vehicle’s airbags would deploy.

Please refer to your vehicle’s Owner’s Manual for reference to the deploy-

ment area of the frontal airbags.

• Do not install this product in a place where it will impair the performance of

any of the vehicle’s operating systems, including airbags and headrests.

To guard against electromagnetic interference

• In order to prevent interference, set the following items as far as possible from this navi-

gation system, other cables or leads:

- TV aerial and aerial lead

- FM, MW/LW aerial and its lead

- GPS aerial and its lead

In addition you should lay or route each aerial lead as far as possible from other aerial

leads.

Do not bind them together, lay or route them together, or cross them.

Such electromagnetic noise will increase the potential for errors in the location display.

Before installing

• Consult with your nearest dealer if installation requires the drilling of holes or other mod-

ifications of the vehicle.

• Before making a final installation of this product, temporarily connect the wiring to con-

firm that the connections are correct and the system works properly.

La pagina sta caricando ...

Pioneer AVIC-D3 Manuale utente

Questo manuale è adatto anche per

Pioneer AVIC-D3 Manuale utente

in altre lingue

Altri documenti