Sony XAV-V10BT Istruzioni per l'uso

XAV-V10BT

4-740-886-41(1)

AV RECEIVER

To cancel the demonstration (Demo) display, see page 13.

For the connection/installation, see page 22.

Para cancelar la pantalla de demostración (Demostración),

consulte la página 14.

Para la conexión/instalación, consulte la página 23.

Per annullare la dimostrazione (Dimostrazione), vedere a

pagina 14.

Per l’installazione e i collegamenti, consultare pagina 23.

Operating Instructions

GB

Manual de instrucciones

ES

Istruzioni per l’uso

IT

2GB

The nameplate indicating operating voltage, etc., is

located on the bottom of the chassis.

Warning

To prevent fire or shock hazard, do not

expose the unit to rain or moisture.

To avoid electrical shock, do not open the

cabinet. Refer servicing to qualified personnel

only.

Made in Thailand

Hereby, Sony Corporation declares that this

equipment is in compliance with Directive 2014/53/

EU.

The full text of the EU declaration of conformity is

available at the following internet address:

http://www.compliance.sony.de/

This equipment is intended to be used with the

approved version(s) of software that are indicated

in the EU Declaration of Conformity.

The software loaded on this equipment is verified

to comply with the essential requirements of the

Directive 2014/53/EU.

The software version can be checked in the

firmware version setting item of the general

settings menu.

The validity of the CE marking is restricted to only

those countries where it is legally enforced, mainly

in the countries EEA (European Economic Area).

Notice for customers: the following

information is only applicable to equipment

sold in countries applying EU Directives

This product has been manufactured by or on

behalf of Sony Corporation.

EU Importer: Sony Europe Limited.

Inquiries to the EU Importer or related to product

compliance in Europe should be sent to the

manufacturer’s authorized representative, Sony

Belgium, bijkantoor van Sony Europe Limited, Da

Vincilaan 7-D1, 1935 Zaventem, Belgium.

Disposal of waste batteries and

electrical and electronic equipment

(applicable in the European Union

and other countries with separate

collection systems)

This symbol on the product, the battery or on the

packaging indicates that the product and the

battery shall not be treated as household waste. On

certain batteries this symbol might be used in

combination with a chemical symbol. The chemical

symbol for lead (Pb) is added if the battery contains

more than 0.004% lead. By ensuring that these

products and batteries are disposed of correctly,

you will help to prevent potentially negative

consequences for the environment and human

health which could be caused by inappropriate

waste handling. The recycling of the materials will

help to conserve natural resources. In case of

products that for safety, performance or data

integrity reasons require a permanent connection

with an incorporated battery, this battery should be

replaced by qualified service staff only. To ensure

that the battery and the electrical and electronic

equipment will be treated properly, hand over

these products at end-of-life to the appropriate

collection point for the recycling of electrical and

electronic equipment. For all other batteries, please

view the section on how to remove the battery from

the product safely. Hand the battery over to the

appropriate collection point for the recycling of

waste batteries. For more detailed information

about recycling of this product or battery, please

contact your local Civic Office, your household

waste disposal service or the shop where you

purchased the product or battery.

Disclaimer regarding services offered by third

parties

Services offered by third parties may be changed,

suspended, or terminated without prior notice.

Sony does not bear any responsibility in these sorts

of situations.

For safety, be sure to install this unit in the

dashboard of the car as the rear side of the unit

becomes hot during use.

For details, see “Connection/Installation”

(page 22).

Warning if your car’s ignition has no ACC

position

Do not install this unit in a car that has no ACC

position. The display of the unit does not turn off

even after turning the ignition off, and this

causes battery drain.

3GB

Caution

IN NO EVENT SHALL SONY BE LIABLE FOR ANY

INCIDENTAL, INDIRECT OR CONSEQUENTIAL

DAMAGES OR OTHER DAMAGES INCLUDING,

WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF

REVENUE, LOSS OF DATA, LOSS OF USE OF THE

PRODUCT OR ANY ASSOCIATED EQUIPMENT,

DOWNTIME, AND PURCHASER’S TIME RELATED TO

OR ARISING OUT OF THE USE OF THIS PRODUCT, ITS

HARDWARE AND/OR ITS SOFTWARE.

Dear customer, this product includes a radio

transmitter.

According to UNECE Regulation no. 10, a vehicle

manufacturers may impose specific conditions for

installation of radio transmitters into vehicles.

Please check your vehicle operation manual or

contact the manufacturer of your vehicle or your

vehicle dealer, before you install this product into

your vehicle.

Emergency calls

This BLUETOOTH car handsfree and the electronic

device connected to the handsfree operate using

radio signals, cellular, and landline networks as well

as user-programmed function, which cannot

guarantee connection under all conditions.

Therefore do not rely solely upon any electronic

device for essential communications (such as

medical emergencies).

On BLUETOOTH communication

• Microwaves emitting from a BLUETOOTH device

may affect the operation of electronic medical

devices. Turn off this unit and other BLUETOOTH

devices in the following locations, as it may cause

an accident.

– where inflammable gas is present, in a hospital,

train, airplane, or petrol station

– near automatic doors or a fire alarm

• This unit supports security capabilities that

comply with the BLUETOOTH standard to provide

a secure connection when the BLUETOOTH

wireless technology is used, but security may not

be enough depending on the setting. Be careful

when communicating using BLUETOOTH wireless

technology.

• We do not take any responsibility for the leakage

of information during BLUETOOTH

communication.

If you have any questions or problems concerning

your unit that are not covered in this manual,

consult your nearest Sony dealer.

Important notice

4GB

Table of Contents

Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Guide to Parts and Controls . . . . . . . . . . . . . . . . . . . 5

Getting Started

Performing Initial Settings . . . . . . . . . . . . . . . . . . . . 7

Preparing a BLUETOOTH Device. . . . . . . . . . . . . . . . 7

Connecting a USB Device . . . . . . . . . . . . . . . . . . . . . 8

Connecting Other Portable Audio Device . . . . . . . . 8

Connecting Rear View Camera . . . . . . . . . . . . . . . . 8

Listening to the Radio

Listening to the Radio. . . . . . . . . . . . . . . . . . . . . . . . 9

Using Tuner Option Functions . . . . . . . . . . . . . . . . . 9

Playback

Playing a USB Device . . . . . . . . . . . . . . . . . . . . . . . 10

Playing a BLUETOOTH Device. . . . . . . . . . . . . . . . . 10

Searching and Playing Tracks. . . . . . . . . . . . . . . . . 10

Other Settings During Playback. . . . . . . . . . . . . . . 11

Handsfree Calling

Receiving a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Making a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Available Operations During a Call . . . . . . . . . . . . 12

Useful Functions

Using Gesture Command . . . . . . . . . . . . . . . . . . . . 13

Settings

Basic Setting Operation . . . . . . . . . . . . . . . . . . . . . 13

General Settings (General) . . . . . . . . . . . . . . . . . . . 13

Sound Settings (Sound) . . . . . . . . . . . . . . . . . . . . . 14

Visual Settings (Visual) . . . . . . . . . . . . . . . . . . . . . . 15

BLUETOOTH Settings (Bluetooth). . . . . . . . . . . . . . 15

Additional Information

Updating the Firmware. . . . . . . . . . . . . . . . . . . . . . 15

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Connection/Installation

Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Parts List for Installation . . . . . . . . . . . . . . . . . . . . 22

Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

5GB

Guide to Parts and Controls

 Display/touch panel

 HOME

Open the HOME menu.

ATT (attenuate)

Press and hold for 1 second to attenuate the

sound.

To cancel, press and hold again, or rotate the

volume control dial.

 Volume control dial

Rotate to adjust the volume when the sound is

output.

OPTION

Press to open the OPTION screen (page 6).

 USB port

 AUX input jack

Main unit

6GB

Playback screen:

HOME screen:

OPTION screen:

 Status indication

 (source option)

Open the source option menu. The available

items differ depending on the source.

 Application specific area

Display playback controls/indications or show

the unit’s status. Displayed items differ

depending on the source.

 Clock (page 13)

 (return to the playback screen)

Switch from the HOME screen to the playback

screen.

 Sources and Settings select keys

Change the source or make various settings.

Display the setting icon and other icons by

swiping the bottom of this area right or left.

 Sounds select keys

Change the sound.

 (EXTRA BASS)

Change the EXTRA BASS setting (page 14).

 (EQ10/Subwoofer)

Change the EQ10/Subwoofer setting (page 14).

 (monitor off)

Turn off the monitor. When the monitor is turned

off, touch any part of the display to turn it back

on.

Screen displays

Lights up when the sound is attenuated.

Lights up when AF (Alternative

Frequencies) is available.

Lights up when the current traffic

information (TA: Traffic Announcement)

is available.

Lights up when the audio device is

playable by enabling the A2DP

(Advanced Audio Distribution Profile).

Lights up when handsfree calling is

available by enabling the HFP (Handsfree

Profile).

Indicates the signal strength status of

the connected cellular phone.

Indicates the remaining battery status of

the connected cellular phone.

Lights up when the Bluetooth® signal is

on. Flashes when the connection is in

progress.

7GB

Performing Initial Settings

You need to perform initial settings before

operating the unit for the first time, after replacing

the car battery, or changing connections.

If the initial settings screen does not appear when

you turn on the unit, perform the factory reset

(page 14) to initialize the unit.

1 Touch [Language], then set the display

language.

2 Touch [Demo] repeatedly to select [OFF] to

disable the demonstration mode.

3 Touch [Set Date/Time], then set the date

and time.

4 After setting the date and time, touch [OK].

5 To return to the previous display, touch ,

then touch [OK].

The startup caution appears.

6 Read through the startup caution, then if

you accept all conditions, touch [Close].

The setting is complete.

This setting can be further configured in the setting

menu (page 13).

Preparing a BLUETOOTH Device

You can enjoy music or perform handsfree calling

depending on the BLUETOOTH compatible device

such as smartphones, cellular phones, and audio

devices (hereafter “BLUETOOTH device” if not

otherwise specified). For details on connecting,

refer to the operating instructions supplied with the

device.

Before connecting the device, turn down the

volume of this unit; otherwise, a loud sound may

result.

When connecting a BLUETOOTH device for the first

time, mutual registration (called “pairing”) is

required. Pairing enables this unit and other devices

to recognize each other.

1 Place the BLUETOOTH device within 1 m

(3 ft) of this unit.

2 Press HOME, then touch [Settings].

3 Touch [Bluetooth].

4 Touch [Bluetooth Connection], then set the

signal to [ON].

The BLUETOOTH signal is turned on and lights

up on the status bar of the unit.

5 Touch [Pairing].

flashes while the unit is in pairing standby

mode.

6 Perform pairing on the BLUETOOTH device

so it detects this unit.

7 Select [XAV-V10BT] shown in the display of

the BLUETOOTH device.

If your model name does not appear, repeat

from step 5.

8 If passkey* input is required on the

BLUETOOTH device, input [0000].

* Passkey may be called “passcode,” “PIN code,” “PIN

number,” “password,” etc., depending on the

BLUETOOTH device.

When pairing is made, stays lit.

9 Select this unit on the BLUETOOTH device to

establish the BLUETOOTH connection.

or lights up when the connection is made.

Notes

• The unit can only be connected with one BLUETOOTH

device at a time.

• To disconnect the BLUETOOTH connection, turn the

connection off from either the unit or the BLUETOOTH

device.

Getting Started

Pairing and connecting with a

BLUETOOTH device

[0000]

Input passkey

8GB

To use a paired device, connection with this unit is

required. Some paired devices will connect

automatically.

1 Press HOME, then touch [Settings].

2 Touch [Bluetooth].

3 Touch [Bluetooth Connection], then touch

[ON].

Make sure that lights up on the status bar of

the unit.

4 Activate the BLUETOOTH function on the

BLUETOOTH device.

5 Operate the BLUETOOTH device to connect

to this unit.

or lights up on the status bar.

To connect the last-connected device from

this unit

When the ignition is turned to on with the

BLUETOOTH signal activated, this unit searches for

the last-connected BLUETOOTH device, and

connection is made automatically.

Note

While streaming BLUETOOTH audio, you cannot connect

from this unit to the cellular phone. Connect from the

cellular phone to this unit instead.

To install the microphone

For details, see “Installing the microphone”

(page 25).

Connecting a USB Device

1 Turn down the volume on the unit.

2 Connect the USB device to the unit.

Connecting Other Portable Audio

Device

1 Turn off the portable audio device.

2 Turn down the volume on the unit.

3 Connect the portable audio device to the

AUX input jack (stereo mini jack) on the unit

with a connecting cord (not supplied)*.

* Be sure to use a straight type plug.

4 Press HOME, then touch [AUX].

To match the volume level of the connected

device to other sources

Start playback of the portable audio device at a

moderate volume, and set your usual listening

volume on the unit.

During playback, touch , then touch [Input

Level]. Adjust the volume level between [-10] and

[+15].

Connecting Rear View Camera

By connecting the optional rear view camera to the

CAMERA IN terminal, you can display the picture

from the rear view camera. For details, see

“Connection/Installation” (page 22).

To display the picture from the rear view

camera

Press HOME, touch [Rear Camera].

Connecting with a paired BLUETOOTH

device

9GB

Listening to the Radio

To listen to the radio, press HOME then touch

[Tuner].

Reception controls/indications

 Current band

Change the band (FM1, FM2, FM3, AM1 or AM2).

 Current frequency, program service name*,

RDS (Radio Data System) indication*

* During RDS reception.

 (tuner option)

Open the tuner option menu.

 SEEK–/SEEK+

Tune in automatically.

 /

Tune in manually.

Touch and hold to continuously skip

frequencies.

 Preset numbers

Select a preset station. Swipe right/left to show

the other preset stations.

Touch and hold to store the current frequency in

that preset.

1 Select the desired band (FM1, FM2, FM3,

AM1 or AM2).

2 Perform tuning.

To tune automatically

Touch SEEK–/SEEK+.

Scanning stops when the unit receives a station.

To tune manually

Touch and hold / to locate the approximate

frequency, then touch / repeatedly to finely

adjust to the desired frequency.

1 While receiving the station that you want to

store, touch and hold the desired preset

number.

1 Select the band, then touch the desired

preset number.

Using Tuner Option Functions

The following functions are available by touching

.

BTM (Best Tuning Memory)

Stores stations in order of frequency on the

preset numbers. 18 stations can be stored for FM

and 12 stations for AM as preset stations.

AF*

Select [ON] to continuously retune the station to

the strongest signal in a network.

TA*

Select [ON] to receive current traffic information

or traffic programs (TP) if available.

Regional*

Select [ON] to stay with the station you are

receiving while the AF function is set to on. If you

leave this regional program’s reception area,

select [OFF]. This function does not work in the

UK and some other areas.

PTY*

Select a program type from the PTY list to search

for a station broadcasting the selected program

type.

* Only available during FM reception.

To receive emergency announcements

With the AF or TA function on, emergency

announcements will automatically interrupt the

currently selected source.

Listening to the Radio

Tuning

Storing manually

Receiving stored stations

10GB

Playing a USB Device

MSC (Mass Storage Class) type USB devices*

compliant with the USB standard can be used.

* e.g., a USB flash drive, digital media player

Notes

• USB devices formatted with file systems FAT12/16/32/

exFAT are supported.

• For details on the compatibility of your USB device, visit

the support site on the back cover.

• For details on the supported file formats, see “Supported

formats for USB playback” (page 16).

1 Turn down the volume on the unit.

2 Connect the USB device to the USB port.

3 Press HOME, then touch [USB].

Playback starts.

To remove the device

Turn the unit off or turn the ignition switch to the

ACC off position, then remove the USB device.

Playing a BLUETOOTH Device

You can play contents on a connected device that

supports BLUETOOTH A2DP (Advanced Audio

Distribution Profile).

1 Make a BLUETOOTH connection with the

audio device (page 7).

2 Press HOME, then touch [BT Audio].

3 Operate the audio device to start playback.

Notes

• Depending on the audio device, information such as title,

track number/time, and playback status may not be

displayed on this unit.

• Even if the source is changed on this unit, playback of the

audio device does not stop.

To match the volume level of the BLUETOOTH

device to other sources

You can reduce the volume level differences

between this unit and the BLUETOOTH device:

During playback, touch , then touch [Input

Level]. Adjust the volume level between [-6] and

[+6].

Searching and Playing Tracks

1 During playback, touch (repeat) or

(shuffle) repeatedly until the desired play

mode appears.

Playback in the selected play mode may take

time to start.

Available play modes differ depending on the

selected sound source and connected device.

1 During USB playback, touch .

The list screen from the currently played item

appears.

Furthermore, touch (audio) or (video) to

list up by file type.

2 Touch the desired item.

Playback starts.

Playback

Repeat play and shuffle play

Searching for a file from the list screen

11GB

Other Settings During Playback

Further settings are available in each source by

touching . The available items differ depending

on the source.

Picture EQ

Adjusts the picture quality according to your

taste: [Dynamic], [Standard], [Theater], [Custom].

(Available only when the parking brake is applied

and USB video is selected.)

Aspect

Selects an aspect ratio for the screen of the unit.

(Available only when the parking brake is applied

and USB video is selected.)

Normal

Displays a 4:3 picture in its original size, with side

bars to fill the 16:9 screen.

Zoom

Displays a 16:9 picture that has been converted

into 4:3 letter box format.

Full

Displays a 16:9 picture in its original size.

Captions

Enlarges the picture horizontally, while fitting

captions in the screen.

To use a cellular phone, connect it with this unit. For

details, see “Preparing a BLUETOOTH Device”

(page 7).

Receiving a Call

1 Touch when a call is received.

The phone call starts.

Note

The ringtone and talker’s voice are output only from the

front speakers.

To reject/end a call

Touch .

Making a Call

1 Press HOME, then touch [Phone].

2 Touch one of the call icons on the

BLUETOOTH phone display.

 (call history)*

Select a contact from the call history list. The

unit stores the last 20 calls.

 (redial)

Make a call automatically to the last contact

you made.

Handsfree Calling

12GB

 (phonebook)*

Select a contact from the name list/number

list in the phonebook. To search for the

desired contact in alphabetical order from

the name list, touch .

 (phone number input)

Enter the phone number.

 Preset phone number list

Select the stored contact.

To store the contact, see “Presetting phone

numbers” (page 12).

* The cellular phone needs to support PBAP (Phone

Book Access Profile).

3 Touch .

The phone call starts.

You can store up to 6 contacts in the preset list.

1 In the phone screen, select a phone number

that you want to store in the preset dial

from the phonebook.

The confirmation display appears.

2 Touch [Add to Preset].

3 Select the preset phone number list where

the phone number is stored.

The contact is stored in the preset phone

number list.

Available Operations During a

Call

To adjust the ringtone volume

Rotate the volume control dial while receiving a call.

To adjust the talker’s voice volume

Rotate the volume control dial during a call.

To adjust the volume for the other party (Mic

gain adjustment)

During a handsfree call, touch , then set

[MIC Gain] to [High], [Middle], or [Low].

To reduce echo and noise (Echo/noise

canceler mode)

During a call, touch , then set [Speech Quality] to

[Mode 1] or [Mode 2].

To switch between handsfree mode and

handheld mode

During a call, touch to switch the

phone call audio between the unit and cellular

phone.

Note

Depending on the cellular phone, this operation may not be

available.

To answer an incoming call automatically

Touch , then set [Auto Answer] to [ON].

Presetting phone numbers

13GB

Using Gesture Command

You can perform frequently-used operations by

swiping your finger on the reception/playback

display.

Basic Setting Operation

You can set items in the following setup categories:

General Settings (General), Sound Settings (Sound),

Visual Settings (Visual), BLUETOOTH Settings

(Bluetooth)

1 Press HOME, then touch [Settings].

2 Touch one of the setup category.

The items that can be set differ depending on

the source and settings.

3 Move the scrollbar up and down to select

the desired item.

To return to the previous display

Touch .

To switch to the playback screen

Touch .

General Settings (General)

Language

Selects the display language: [English],

[Español], [Français], [Deutsch], [Italiano],

[Português], [], [ ], [ ], [ ],

[], [].

Demo

Activates the demonstration: [OFF], [ON].

Date/Time

Date Format

Selects the format: [DD/MM/YY], [MM/DD/YY],

[YY/MM/DD].

Time Format

Selects the format: [12-hour], [24-hour].

Set Date/Time

Sets the date and clock time manually.

Beep

Activates the operation sound: [OFF], [ON].

Useful Functions

Do this To

Swipe left to right

Radio reception:

seek forward stations.

Video/audio playback:

skip forward a file/track.

Swipe right to left

Radio reception:

seek backward stations.

Video/audio playback:

skip backward a file/track.

Swipe upwards

Radio reception:

receive stored stations

(go forward).

Swipe downwards

Radio reception:

receive stored stations

(go backward).

Settings

14GB

Rear View Camera

Selects the image from the rear view camera:

[OFF], [Normal], [Reverse] (mirror image).

[Guide Line Adjust] adjusts the guide on the

picture from the rear view camera.

Touch the near side  or far

side  (red portions) of the

guide to adjust.

Touch /// to adjust

the guide position, and touch

[ ] or [ ] to adjust the guide width.

Steering Control

Selects the input mode for the connected remote

control. To prevent a malfunction, be sure to

match the input mode with the connected

remote control before use.

Custom

Input mode for the steering wheel remote

control (follow the procedures of [ ] to register

functions on the connected remote control).

Preset

Input mode for the wired remote control

excluding the steering wheel remote control.

The steering button panel appears.

 Press and hold the button you want to assign

to the steering wheel.

The button on the panel lights up (standby).

 Press and hold the button on the steering

wheel you want to assign the function to.

The button on the panel will change the color

(highlighted or encircled by an orange line).

 To register other functions, repeat steps 

and .

(Available only when [Steering Control] is set to

[Custom].)

Notes

• While making settings, the connected remote control

cannot be used even though some functions have

already been registered. Use the buttons on the unit.

• If an error occurs while registering, all the registered

information is cleared. Restart registration from the

beginning.

• This function may not be available on some vehicles.

For details on the compatibility of your vehicle, visit the

support site on the back cover.

Clock Time

Sets the clock time by the RDS data: [OFF], [ON].

Factory Reset

Initializes all the settings to the factory settings.

Firmware Version

Updates and confirms the firmware version.

Open Source Licenses

Displays the software licenses.

Sound Settings (Sound)

EXTRA BASS

Reinforces bass sound in synchronization with

the volume level: [OFF], [1], [2].

EQ10/Subwoofer

Selects an equalizer curve and adjusts the

subwoofer level.

EQ10

Selects the equalizer curve: [OFF], [R&B], [Rock],

[Pop], [Dance], [Hip-Hop], [EDM], [Jazz], [Soul],

[Country], [Custom].

[Custom] adjusts the equalizer curve: –6 to +6.

Subwoofer

Adjusts the volume level of the subwoofer:

[OFF], –10 to +10.

Balance/Fader

Adjusts the balance/fader level.

Balance

Adjusts the sound balance between the left and

right speakers: [L15] to [R15].

Fader

Adjusts the sound balance between the front

and rear speakers: [Front 15] to [Rear 15].

Crossover

Adjusts the cut-off frequency and subwoofer

phase.

High Pass Filter

Selects the cut-off frequency of the front/rear

speakers: [OFF], [50Hz], [60Hz], [80Hz], [100Hz],

[120Hz].

Low Pass Filter

Selects the cut-off frequency of the subwoofer:

[OFF], [50Hz], [60Hz], [80Hz], [100Hz], [120Hz].

Subwoofer Phase

Selects the subwoofer phase: [Normal],

[Reverse].

DSO (Dynamic Stage Organizer)

Enhances audio output: [OFF], [Low], [Middle],

[High].

15GB

Visual Settings (Visual)

Wallpaper

Changes the wallpaper by touching the desired

color.

Dimmer

Dims the display: [OFF], [Auto], [ON].

([Auto] is available only when the illumination

control lead is connected and works when the

head light is turned on.)

[ ] adjusts the brightness level when the

dimmer is activated: –5 to +5.

Touch Panel Adjust

Adjusts the touch panel calibration if the

touching position does not correspond with the

proper item.

BLUETOOTH Settings (Bluetooth)

Bluetooth Connection

Activates the BLUETOOTH signal: [OFF], [ON],

[Pairing] (enters into pairing standby mode).

Bluetooth Device Info

Displays the information of the device connected

to the unit.

(Available only when [Bluetooth Connection] is

set to [ON] and a BLUETOOTH device is

connected to the unit.)

Bluetooth Reset

Initializes all BLUETOOTH-related settings such as

pairing information, call history, history of

connected BLUETOOTH devices, etc.

Updating the Firmware

To update the firmware, visit the support site on the

back cover, then follow the online instructions.

Note

During the update, do not remove the USB device.

Precautions

• Power antenna (aerial) extends automatically.

• When you transfer ownership or dispose of your

car with the unit installed, initialize all the settings

to the factory settings by performing the factory

reset (page 14).

• Do not splash liquid onto the unit.

Notes on safety

• Comply with your local traffic rules, laws, and

regulations.

• While driving

– Do not watch or operate the unit, as it may lead

to distraction and cause an accident. Park your

car in a safe place to watch or operate the unit.

– Do not use the setup feature or any other

function which could divert your attention from

the road.

– When backing up your car, be sure to look back

and watch the surroundings carefully for your

safety even if the rear view camera is connected.

Do not depend on the rear view camera

exclusively.

• While operating

– Do not insert your hands, fingers, or foreign

objects into the unit as it may cause injury or

damage to the unit.

– Keep small articles out of the reach of children.

– Be sure to fasten seatbelts to avoid injury in the

event of sudden movement of the car.

Additional Information

Preventing an accident

Pictures appear only after you park the car and

set the parking brake.

If the car starts moving during video playback,

the following caution is displayed and you

cannot watch the video.

[Video blocked for your safety.]

Do not operate the unit or watch the monitor

while driving.

16GB

Notes on LCD panel

• Do not get the LCD panel wet or expose it to

liquids. This may cause a malfunction.

•Do not press down hard on the LCD panel as doing

so can distort the picture or cause a malfunction

(i.e., the picture may become unclear or the LCD

panel may be damaged).

•Do not touch the panel with objects other than

with your finger as it may damage or break the

LCD panel.

•Clean the LCD panel with a dry soft cloth. Do not

use solvents such as benzine, thinner,

commercially available cleaners, or antistatic

spray.

•Do not use the unit outside the temperature range

0 ºC – 40 ºC (32 ºF – 104 ºF).

• If your car was parked in a cold or hot place, the

picture may not be clear. However, the monitor is

not damaged and the picture will become clear

after the temperature in your car becomes normal.

•Some stationary blue, red, or green dots may

appear on the monitor. These are called “bright

spots” and can happen with any LCD. The LCD

panel is precision-manufactured with more than

99.99% of its segments functional. However, it is

possible that a small percentage (typically 0.01%)

of the segments may not light up properly. This

will not, however, interfere with your viewing.

Notes on the touch panel

• This unit uses a resistive touch panel. Touch the

panel directly with your fingertip.

•Multi-touch operation is not supported on this

unit.

•Do not touch the panel with sharp objects such as

a needle, pen, or fingernail. Operation with a

stylus is not supported on this unit.

• Do not let any objects contact the touch panel. If

the panel is touched by an object other than your

fingertip, the unit may not respond correctly.

• Since glass material is used for the panel, do not

subject the unit to strong shock. If cracking or

chipping occurs on the panel, do not touch the

damaged part as it may cause injury.

•Keep other electrical devices away from the touch

panel. They may cause the touch panel to

malfunction.

 WMA (.wma)*

1

*

2

Bit rate: 48 kbps – 192 kbps (Supports variable bit

rate (VBR))*

3

Sampling frequency*

4

: 44.1 kHz

 MP3 (.mp3)*

1

*

2

Bit rate: 48 kbps – 320 kbps (Supports variable

bit rate (VBR))*

3

Sampling frequency*

4

: 32 kHz, 44.1 kHz, 48 kHz

 AAC (.m4a)*

1

*

2

Bit rate: 40 kbps – 320 kbps (Supports variable

bit rate (VBR))*

3

Sampling frequency*

4

: 8 kHz – 48 kHz

Bit per sample (Quantization bit): 16 bits

 FLAC (.flac)*

1

*

6

Sampling frequency*

4

: 8 kHz – 48 kHz

Bit per sample (Quantization bit): 16 bits

 WAV (.wav)*

1

Sampling frequency*

4

: 8 kHz – 48 kHz

Bit per sample (Quantization bit): 16 bits, 24 bits

 Xvid (.avi)

Video codec: MPEG-4 Advanced Simple Profile

Audio codec: MP3 (MPEG-1 Layer3)

Bit rate: Max. 4 Mbps

Frame rate: Max. 30 fps (30p/60i)

Resolution: Max. 1280 × 720*

5

 MPEG-4 (.mp4)

Video codec: MPEG-4 Advanced Simple Profile,

AVC Baseline Profile

Audio codec: AAC

Bit rate: Max. 4 Mbps

Frame rate: Max. 30 fps (30p/60i)

Resolution: Max. 1280 × 720*

5

 WMV (.wmv, .avi)*

1

Video codec: WMV3, WVC1

Audio codec: MP3, WMA

Bit rate: Max. 6 Mbps

Frame rate: Max. 30 fps

Resolution: Max. 720 × 480*

5

 MKV (.mkv)

Video codec: MPEG-4 Advanced Simple Profile,

AVC Baseline Profile

Audio codec: MP3, AAC

Bit rate: Max. 5 Mbps

Frame rate: Max. 30 fps

Resolution: Max. 1280 × 720*

5

*1 Copyright-protected files and multi-channel audio files

cannot be played back.

*2 DRM (Digital Rights Management) files cannot be played

back.

*3 Non-standard bit rates or non-guaranteed bit rates are

included depending on the sampling frequency.

*4 Sampling frequency may not correspond to all encoders.

*5 These numbers indicate the maximum resolution of

playable video and do not indicate the player’s display

resolution. The display resolution is 800 × 480.

*6 Displaying the tag information is not supported.

Note

Some files may not be played back even though their file

formats are supported by the unit.

Supported formats for USB playback

17GB

This product contains software that Sony uses under a

licensing agreement with the owner of its copyright. We are

obligated to announce the contents of the agreement to

customers under requirement by the owner of copyright for

the software.

For details on software licenses, see page 14.

Notice on GNU GPL/LGPL applied software

This product contains software that is subject to the

following GNU General Public License (hereinafter referred

to as “GPL”) or GNU Lesser General Public License

(hereinafter referred to as “LGPL”). These establish that

customers have the right to acquire, modify, and

redistribute the source code of said software in accordance

with the terms of the GPL or LGPL displayed on this unit.

The source code for the above-listed software is available

on the Web.

To download, please access the following URL then select

the model name “XAV-V10BT.”

URL: http://www.sony.net/Products/Linux/

Please note that Sony cannot answer or respond to any

inquiries regarding the content of the source code.

If you have any questions or problems concerning your unit

that are not covered in this Operating Instructions, consult

your nearest Sony dealer.

Specifications

Monitor section

Display type: Wide LCD color monitor

Dimensions: 6.2 in

System: TFT active matrix

Number of pixels:

1,152,000 pixels (800 × 3 (RGB) × 480)

Color system:

PAL/NTSC automatic select for CAMERA IN

terminal

Tuner section

FM

Tuning range: 87.5 MHz – 108.0 MHz

Usable sensitivity: 7 dBf

Signal-to-noise ratio: 70 dB (mono)

Separation at 1 kHz: 45 dB

AM

Tuning range: 531 kHz – 1,602 kHz

Sensitivity: 32 µV

USB player section

Interface: USB (Hi-speed)

Maximum current: 1.5 A

Wireless communication

Communication System:

BLUETOOTH Standard version 3.0

Output:

BLUETOOTH Standard Power Class 2

(Max. Conducted +1 dBm)

Maximum communication range*

1

:

Line of sight approx. 10 m (33 ft)

Frequency band:

2.4 GHz band (2.4000 GHz – 2.4835 GHz)

Modulation method: FHSS

Compatible BLUETOOTH Profiles*

2

:

A2DP (Advanced Audio Distribution Profile) 1.3

AVRCP (Audio Video Remote Control Profile) 1.3

HFP (Handsfree Profile) 1.6

PBAP (Phone Book Access Profile) 1.1

Corresponding codec: SBC, AAC

*1 The actual range will vary depending on factors such as

obstacles between devices, magnetic fields around a

microwave oven, static electricity, reception sensitivity,

antenna (aerial)’s performance, operating system,

software application, etc.

*2 BLUETOOTH standard profiles indicate the purpose of

BLUETOOTH communication between devices.

Notice on license

18GB

Power amplifier section

Outputs: Speaker outputs

Speaker impedance: 4  – 8 

Maximum power output: 55 W × 4 (at 4 )

General

Power requirements: 12 V DC car battery

(negative ground (earth))

Rated current consumption: 10 A

Dimensions:

Approx. 178 mm × 100 mm × 141 mm

(7

1

/8 in × 4 in × 5

5

/8 in) (w/h/d)

Mounting dimensions:

Approx. 182 mm × 111 mm × 121 mm

(7

1

/4 in × 4

3

/8 in × 4

7

/8 in) (w/h/d)

Mass: Approx. 0.9 kg (1 lb 16 oz)

Package contents:

Main unit (1)

Parts for installation and connections (1 set)

Microphone (1)

Ask the dealer for detailed information.

Design and specifications are subject to change

without notice.

The Bluetooth® word mark and logos are registered

trademarks owned by the Bluetooth SIG, Inc. and any use of

such marks by Sony Corporation is under license. Other

trademarks and trade names are those of their respective

owners.

Windows Media is either a registered trademark or

trademark of Microsoft Corporation in the United States

and/or other countries.

This product is protected by certain intellectual property

rights of Microsoft Corporation. Use or distribution of such

technology outside of this product is prohibited without a

license from Microsoft or an authorized Microsoft subsidiary.

THIS PRODUCT IS LICENSED UNDER THE MPEG-4 VISUAL

PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND NON-

COMMERCIAL USE OF A CONSUMER FOR DECODING VIDEO

IN COMPLIANCE WITH THE MPEG-4 VISUAL STANDARD

(“MPEG-4 VIDEO”) THAT WAS ENCODED BY A CONSUMER

ENGAGED IN A PERSONAL AND NONCOMMERCIAL ACTIVITY

AND/OR WAS OBTAINED FROM A VIDEO PROVIDER

LICENSED BY MPEG LA TO PROVIDE MPEG-4 VIDEO.

NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY

OTHER USE.

ADDITIONAL INFORMATION INCLUDING THAT RELATING TO

PROMOTIONAL, INTERNAL AND COMMERCIAL USES AND

LICENSING MAY BE OBTAINED FROM MPEG LA, LLC. SEE

HTTP://WWW.MPEGLA.COM

THIS PRODUCT IS LICENSED UNDER THE AVC PATENT

PORTFOLIO LICENSE FOR THE PERSONAL AND NON-

COMMERCIAL USE OF A CONSUMER TO

(i)ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD

(“AVC VIDEO”)

AND/OR

(ii)DECODE AVC VIDEO THAT WAS ENCODED BY A

CONSUMER ENGAGED IN A PERSONAL AND

NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM

A VIDEO PROVIDER LICENSED TO PROVIDE AVC VIDEO. NO

LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER

USE. ADDITIONAL INFORMATION MAY BE OBTAINED FROM

MPEG LA, L.L.C. SEE

HTTP://WWW.MPEGLA.COM

THIS PRODUCT IS LICENSED UNDER THE AVC PATENT

PORTFOLIO LICENSE AND VC-1 PATENT PORTFOLIO LICENSE

FOR THE PERSONAL AND NON-COMMERCIAL USE OF A

CONSUMER TO DECODE VIDEO IN COMPLIANCE WITH THE

AVC STANDARD (“AVC VIDEO”) AND/OR THE VC-1 STANDARD

(“VC-1 VIDEO”) THAT WAS ENCODED BY A CONSUMER

ENGAGED IN A PERSONAL AND NONCOMMERCIAL ACTIVITY

AND/OR WAS OBTAINED FROM A VIDEO PROVIDER

LICENSED TO PROVIDE AVC VIDEO AND/OR VC-1 VIDEO. NO

LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER

USE. ADDITIONAL INFORMATION MAY BE OBTAINED FROM

MPEG LA, L.L.C. SEE HTTP://WWW.MPEGLA.COM

All other trademarks are trademarks of their respective

owners.

Copyrights

19GB

Troubleshooting

The following checklist will help you remedy

problems you may encounter with your unit.

Before going through the checklist below, check

the connection and operating procedures.

For details on using the fuse and removing the unit

from the dashboard, see “Connection/Installation”

(page 22).

If the problem is not solved, visit the support site on

the back cover.

General

There is no beep sound.

 An optional power amplifier is connected and

you are not using the built-in amplifier.

The fuse has blown.

The unit makes noise when the position of the

ignition is switched.

 The leads are not matched correctly with the car’s

accessory power connector.

The display disappears from/does not appear on

the monitor.

 The monitor off function is activated (page 6).

– Touch anywhere on the display to turn the

display back on.

Menu items cannot be selected.

 Unavailable menu items are displayed in gray.

The USB functions do not work properly.

 Do not use a USB extension cable as it may cause

deterioration of signal quality.

– Use a shorter USB cable when connecting the

USB device, or replace the USB cable with a new

one.

The unit cannot be operated.

 Press and hold HOME for more than 10 seconds

to restart the unit. For your safety, do not restart

the unit while you are driving.

Touch panel operation

The touch panel does not react to your touch

correctly.

 Touch one part of the touch panel at a time. If

two or more parts are touched simultaneously,

the touch panel will not react correctly.

 Calibrate the touch panel of the display (page 15).

 Touch the pressure sensitive panel firmly.

Multi-touch is not recognized.

 Multi-touch operation is not supported on this

unit.

Radio reception

The radio reception is poor.

Static noise occurs.

 Connect the antenna (aerial) firmly.

RDS

PTY displays [PTY not found.].

 The current station is not an RDS station, or the

radio reception is poor.

Seek starts after a few seconds of listening.

 The station is non-TP or has a weak signal.

– Deactivate TA (page 9).

There are no traffic announcements.

 Activate TA (page 9).

 The station does not broadcast any traffic

announcements despite being TP.

– Tune into another station.

Picture

There is no picture/picture noise occurs.

 A connection has not been made correctly.

 Check the connection between this unit and

other equipment and set the input selector of the

equipment to the source corresponding to this

unit.

 Installation is not correct.

– Install the unit at an angle of less than 30° in a

sturdy part of the car.

 The parking cord (light green) is not connected to

the parking brake switch cord, or the parking

brake is not applied.

The picture does not fit in the screen.

 The aspect ratio is fixed on the playback source.

Sound

There is no sound/sound skips/sound cracks.

 A connection has not been made correctly.

 Check the connection between this unit and the

connected equipment and set the input selector

of the equipment to the source corresponding to

this unit.

 Installation is not correct.

– Install the unit at an angle of less than 30° in a

sturdy part of the car.

 The unit is in pause/reverse/fast-forward mode.

 The settings for the outputs are not made

correctly.

 The volume is too low.

 The ATT function is activated.

 The format is not supported.

– Check if the format is supported by this unit

(page 16).

20GB

Sound is noisy.

 Keep cords and cables away from each other.

USB playback

Items cannot be played.

 Reconnect the USB device.

The USB device takes longer to play.

 The USB device contains large-sized files or files

with a complicated tree structure.

Audio files cannot be played.

 USB devices formatted with file systems other

than FAT12, FAT16, FAT32 or exFAT are

unsupported.*

* This unit supports FAT12, FAT16, FAT32 and exFAT, but

some USB device may not support all of these. For details,

refer to the operating instructions of each USB device or

contact the manufacturer.

The USB-connected smartphone cannot be

played.

 USB connection is only available for USB devices

in MSC mode.

– When using smartphones, make a BLUETOOTH

connection (page 7).

BLUETOOTH function

The other BLUETOOTH device cannot detect this

unit.

 Set [Bluetooth Connection] to [ON] (page 15).

 While connecting to a BLUETOOTH device, this

unit cannot be detected by another device.

Terminate the current connection and search for

this unit from the other device.

 Depending on your smartphone or cellular

phone, you may need to delete this unit from the

history of the connected smartphone or cellular

phone then pair them again (page 7).

Connection is not possible.

 Check the pairing and connection procedures in

the manual of the other device, etc., and perform

the operation again.

The name of the detected device does not

appear.

 Depending on the status of the other device, it

may not be possible to obtain the name.

There is no ringtone.

 Raise the volume while receiving a call.

The talker’s voice volume is low.

 Raise the volume during a call.

The other party says that the volume is too low

or high.

 Adjust the [MIC Gain] level (page 12).

Echo or noise occurs during call conversations.

 Reduce the volume.

 Set [Speech Quality] to [Mode 1] or [Mode 2].

(page 12).

 If ambient noise other than the phone call sound

is loud, try reducing this noise.

– Shut the window if road noise is loud.

– Lower the air conditioner if the air conditioner is

loud.

The phone sound quality is poor.

 Phone sound quality depends on reception

conditions of the cellular phone.

– Move your car to a place where you can

enhance the cellular phone’s signal if the

reception is poor.

The volume of the connected BLUETOOTH device

is low or high.

 Volume level will differ depending on the

BLUETOOTH device.

– Reduce the volume level differences between

this unit and the BLUETOOTH device (page 10).

The sound skips during audio streaming or the

BLUETOOTH connection fails.

 Reduce the distance between the unit and the

BLUETOOTH device.

 If the BLUETOOTH device is stored in a case which

interrupts the signal, remove the case while

using the device.

 Several BLUETOOTH devices or other devices (e.g.

ham radio devices) which emit radio waves are

used nearby.

– Turn off the other devices.

– Increase the distance between the unit and

other devices.

 Playback sound stops momentarily when this

unit is connecting to a cellular phone. This is not

a malfunction.

The connected BLUETOOTH device cannot be

controlled during audio streaming.

 Check that the connected BLUETOOTH device

supports AVRCP.

Some functions do not work.

 Check that the connecting device supports the

functions in question.

A call is answered unintentionally.

 The connecting phone is set to start a call

automatically.

 [Auto Answer] of this unit is set to [ON] (page 12).

Pairing failed due to time out.

 Depending on the connecting device, the time

limit for pairing may be short. Try completing the

pairing within the time.

La pagina sta caricando ...

Sony XAV-V10BT Istruzioni per l'uso

Sony XAV-V10BT Istruzioni per l'uso

in altre lingue

Documenti correlati

Altri documenti