Hisense R32 Air Conditioner Manuale utente

Thank you very much for purchasing this Air Conditioner. Please

read this use and installation instructions carefully before installing

and using this appliance and keep this manual for future reference.

ENGLISH 意大利文 ESPAÑOL PORTUGUÊS

ITALIANO

Contents

3

1

13

14

15

16

17

13

Safety instructions

Preparation before use

Safety Precautions

Installation instructions

Installation diagram

Select the installation locations

Connecting of the cable

Wiring diagram

Outdoor unit installation

Air purging

4

1

Safety instructions

1. To guarantee the unit work normally, please read the manual carefully before

installation, and try to install strictly according to this manual.

2. Do not let air enter the refrigeration system or discharge refrigerant when moving the

air conditioner.

6. After installing, the consumer must operate the air conditioner correctly

according to this manual, keep a suitable storage for maintenance and moving of

the air conditioner in the future.

5. There must be an air-break switch.

4. Check the connecting cables and pipes carefully, make sure they are correct and firm

before connecting the power of the air conditioner.

7. Fuse of indoor unit: T 3.15A 250VAC or T 5A 250VAC. Please refer to the screen

printing on the circuit board for the actual parameters, which must be consistent with the

parameters on the screen printing.

8. For 7k 12k models, f T 15A 250VAC or T 20A 250VAC.

refer to the screen printing on the circuit board for the actual parameters, which must be

consistent with the parameters on the screen printing.

~ use of outdoor unit: Please

3. Properly ground the air conditioner into the earth.

10. For 24k models, f T 30A 250VAC . use of outdoor unit:

12. Warning: Risk of electric shock can cause injury or death: Disconnect all

remote electric power supplies before servicing .

11. The installation instructions for appliances that are intended to be permanently

connected to fixed wiring, and have a leakage current that may exceed 10 mA,

shall state that the installation of a residual current device (RCD) having a rated

residual operating current not exceeding 30 mA is advisable.

13. The maximum length of the connecting pipe between the indoor unit and

outdoor unit should be less than 5 meters. It will affect the efficiency of the air

conditioner if the distance longer than that length.

15. This appliance can be used by children aged from 8 years and above and

persons with reduced physical, sensory or mental capabilities or lack of experience

and knowledge if they have been given supervision or instruction concerning use

of the appliance in a safe way and understand the hazards involved. Children shall

not play with the appliance. Cleaning and user maintenance shall not be made by

children without supervision.

16.The batteries in remote controller must be recycled or disposed of properly.

Disposal of Scrap Batteries --- Please discard the batteries as sorted municipal

waste at the accessible collection point.

9. For models, f 20A 250VAC. 18k use of outdoor unit: T

14. This appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or instruction concerning use

of the appliance by a person responsible for their safety.Children should be

supervised to ensure that they do not play with the appliance.

2

Safety instructions

21. The appliance shall not be installed in the laundry.

19. The appliance shall be installed in accordance with national wiring regulations.

20. The air conditioner must be installed by professional or qualified persons.

18. If the supply cord is damaged, it must be replaced by the manufacturer, its

service agent or similarly qualified persons in order to avoid a hazard.

22. Regarding to installation, please refer to section “Installation instructions”.

23. Regarding to maintenance, please refer to section “Maintenance”.

24. For models using R32 refrigerant, piping connection should be conducted on

outdoor side.

17. If the appliance is fixed wiring, the appliance must be fitted with means for

disconnection from the supply mains having a contact separation in all poles that

provide full disconnection under over voltage category III conditions, and these

means must be incorporated in the fixed wiring in accordance with the wiring rules.

3

Preparation before use

The air conditioner has an Auto-Restart function.

Each time after the remote control is replaced with new batteries or is energized, auto presetting

heat pump.If the air conditioner you purchased is a Cooling Only one, heat pump remote controller can also be used.

remote control

Remote Control presetting

Before using the air conditioner, be sure to check and preset the following.

Auto Restart Presetting

Hold down any button on remote control to activate the back light. It automatically shuts off 10 seconds later.

Note: Back-light is an optional function.

Back-light function (optional) of Remote Control

This appliance is made of recyclable or re-usable material. Scrapping must be carried out in

compliance with local waste disposal regulations. Before scrapping it, make sure to cut off the

mains cord so that the appliance cannot be re-used.

For more detailed information on handling and recycling this product, contact your local authorities

who deal with the separate collection of rubbish or the shop where you bought the appliance.

SCRAPPING OF APPLIANCE

This appliance is marked according to the European Directive 2012/19/EC,

Waste Electrical and Electronic Equipment (WEEE).

This marking indicates that this product should not be disposed

with other household wastes throughout the EU. To prevent possible

harm to the environment or human health from uncontrolled waste

disposal,recycle it responsibly to promote the sustainable reuse of

material resources. To return your used device, please use the return

and collection systems or contact the retailer where the product was

purchased. They can take this product for environmental safe recycling.

Note

Preset

Safeguarding the environment

When charging refrigerant into the system, make sure to charge in liquid state,if the

refrigerant of the appliance is R32.Otherwise, chemical composition of refrigerant

(R32) inside the system may change and thus affect performance of the air conditioner.

According to the character of

of the tube is very high, so be sure to be careful when you install and repair the

appliance.

refrigerant (R32,the value of GWP is 675), the pressure

If the supply cord is damaged, it must be replaced by the manufacturer, its

service agent or similarly qualified persons in order to avoid a hazard.

Installation of this product must be done by experienced service technicians

professional installers only in accordance with this manual.

The temperature of refrigerant circuit will be high, please keep the

interconnection cable away from the copper tube.

For the multi system, the refrigerant refer to the multi outdoor unit.

Safety precautions

Symbols in this Use and Care Manual are interpreted as shown below.

Be sure not to do.

Pay attention to such a situation.

Grounding is essential.

Warning: Incorrect handling could

cause a serious hazard, such as death,

serious injury, etc.

4

Do not use the power supply

circuit breaker or pull off the plug

to turn it off during operation.

This may cause a fire due to

spark, etc.

Keep the power supply circuit

breaker or plug from dirt.

Connect the power supply cord

to it firmly and correctly, lest an

electric shock or a fire break out

due to insufficient contact.

Use correct power supply in

accordance with the rating plate

requirement. Otherwise, serious

faults or hazard may occur or a

fire maybe break out.

Do not knit, pull or press the power

supply cord, lest the power supply cord

be broken. An electric shock or fire is

probably caused by a broken power

supply cord.

Never insert a stick or similar obstacle

to the unit. Since the fan rotates at high

speed, this may cause an injury.

Do not repair the appliance by yourself.

If this is done incorrectly, it may cause

an electric shock, etc.

Turn off the appliance by remote

control firstly before cutting off

power supply if malfunction occurs.

It is harmful to your health if the cool

air reaches you for a long time. It is

advisable to let the air flow be

deflected to all the room.

Prevent the air flow from reaching

the gas burners and stove.

Do not touch the operation buttons

when your hands are wet.

Do not put any objects on the outdoor

unit.

It is the user's responsibility to

make the appliance be grounded

according to local codes or

ordinances by a licenced

technician.

OFF

ON

OFF

MODE

SMART

QUIET DIM MER

ECONOM Y

FEEL

FAN SPEED

CLOCK

TIMER ON

TIMER OFF

SLEEP

TEMP.

SUPER

Safety precautions

Precautions for using R32 refrigerant

5

The basic installation work procedures are the same as the conventional refrigerant

(R22 or R410A). However, pay attention to the following points:

CAUTION

1. Transport of equipment containing flammable refrigerants

Compliance with the transport regulations

2. Marking of equipment using signs

Compliance with local regulations

3. Disposal of equipment using flammable refrigerants

Compliance with national regulations

4. Storage of equipment/appliances

The storage of equipment should be in accordance with the manufacturer's

instructions.

5. Storage of packed (unsold) equipment

Storage package protection should be constructed such that mechanical

damage to the equipment inside the package will not cause a leak of the

refrigerant charge.

The maximum number of pieces of equipment permitted to be stored together

will be determined by local regulations.

6. Information on servicing

6-1 Checks to the area

Prior to beginning work on systems containing flammable refrigerants, safety

checks are necessary to ensure that the risk of ignition is minimised. For repair

to the refrigerating system, the following precautions shall be complied with

prior to conducting work on the system.

6-2 Work procedure

Work shall be undertaken under a controlled procedure so as to minimise the

risk of flammable gas or vapour being present while the work is being

performed.

6-3 General work area

All maintenance staff and others working in the local area shall be instructed

on the nature of work being carried out. Work in confined spaces shall be

avoided.

The area around the workspace shall be sectioned off. Ensure that the

conditions within the area have been made safe by control of flammable

material.

6-4 Checking for presence of refrigerant

The area shall be checked with an appropriate refrigerant detector prior to and

during work, to ensure the technician is aware of potentially flammable

atmospheres.

Ensure that the leak detection equipment being used is suitable for use with

flammable refrigerants, i.e. non-sparking, adequately sealed or intrinsically

safe.

Safety precautions

6

CAUTION

6-5 Presence of fire extinguisher

If any hot work is to be conducted on the refrigeration equipment or any

associated parts, appropriate fire extinguishing equipment shall be available

to hand.

Have a dry powder or CO2 fire extinguisher adjacent to the charging area.

6-6 No ignition sources

No person carrying out work in relation to a refrigeration system which involves

exposing any pipe work that contains or has contained flammable refrigerant

shall use any sources of ignition in such a manner that it may lead to the risk of

fire or explosion.

All possible ignition sources, including cigarette smoking, should be kept

sufficiently far away from the site of installation, repairing, removing and

disposal, during which flammable refrigerant can possibly be released to the

surrounding space.

Prior to work taking place, the area around the equipment is to be surveyed to

make sure that there are no flammable hazards or ignition risks. “No Smoking”

signs shall be displayed.

6-7 Ventilated area

Ensure that the area is in the open or that it is adequately ventilated before

breaking into the system or conducting any hot work.

A degree of ventilation shall continue during the period that the work is carried

out.

The ventilation should safely disperse any released refrigerant and preferably

expel it externally into the atmosphere.

6-8 Checks to the refrigeration equipment

Where electrical components are being changed, they shall be fit for the

purpose and to the correct specification.

At all times the manufacturer's maintenance and service guidelines shall be

followed. If in doubt consult the manufacturer's technical department for

assistance.

The following checks shall be applied to installations using flammable

refrigerants:

– The charge size is in accordance with the room size within which the

refrigerant containing parts are installed;

– The ventilation machinery and outlets are operating adequately and are not

obstructed;

– If an indirect refrigerating circuit is being used, the secondary circuit shall be

checked for the presence of refrigerant;

– Marking to the equipment continues to be visible and legible. Markings and

signs that are illegible shall be corrected;

– Refrigeration pipe or components are installed in a position where they are

unlikely to be exposed to any substance which may corrode refrigerant

containing components, unless the components are constructed of materials

Safety precautions

7

CAUTION

which are inherently resistant to being corroded or are suitably protected

against being so corroded.

6-9 Checks to electrical devices

Repair and maintenance to electrical components shall include initial safety

checks and component inspection procedures.

If a fault exists that could compromise safety, then no electrical supply shall be

connected to the circuit until it is satisfactorily dealt with.

If the fault cannot be corrected immediately but it is necessary to continue

operation, an adequate temporary solution shall be used.

This shall be reported to the owner of the equipment so all parties are advised.

Initial safety checks shall include:

– That capacitors are discharged: this shall be done in a safe manner to avoid

possibility of sparking;

– That there no live electrical components and wiring are exposed while

charging, recovering or purging the system;

– That there is continuity of earth bonding.

7. Repairs to sealed components

During repairs to sealed components, all electrical supplies shall be

disconnected from the equipment being worked upon prior to any removal of

sealed covers, etc.

If it is absolutely necessary to have an electrical supply to equipment during

servicing, then a permanently operating form of leak detection shall be located

at the most critical point to warn of a potentially hazardous situation.

Particular attention shall be paid to the following to ensure that by working on

electrical components, the casing is not altered in such a way that the level of

protection is affected.

This shall include damage to cables, excessive number of connections,

terminals not made to original specification, damage to seals, incorrect fitting

of glands, etc.

Ensure that apparatus is mounted securely.

Ensure that seals or sealing materials have not degraded such that they no

longer serve the purpose of preventing the ingress of flammable atmospheres.

Replacement parts shall be in accordance with the manufacturer's

specifications.

NOTE:

The use of silicon sealant may inhibit the effectiveness of some types of

leak detection equipment. Intrinsically safe components do not have to be

isolated prior to working on them.

8. Repair to intrinsically safe components

Do not apply any permanent inductive or capacitance loads to the circuit

without ensuring that this will not exceed the permissible voltage and current

permitted for the equipment in use.

Intrinsically safe components are the only types that can be worked on while

Safety precautions

8

CAUTION

live in the presence of a flammable atmosphere. The test apparatus shall be at

the correct rating.

Replace components only with parts specified by the manufacturer.

Other parts may result in the ignition of refrigerant in the atmosphere from a

leak.

9. Cabling

Check that cabling will not be subject to wear, corrosion, excessive pressure,

vibration, sharp edges or any other adverse environmental effects.

The check shall also take into account the effects of aging or continual

vibration from sources such as compressors or fans.

10.Detection of flammable refrigerants

Under no circumstances shall potential sources of ignition be used in the

searching for or detection of refrigerant leaks.

A halide torch (or any other detector using a naked flame) shall not be used.

11.Leak detection methods

The following leak detection methods are deemed acceptable for systems

containing flammable refrigerants:

– Electronic leak detectors shall be used to detect flammable refrigerants, but

the sensitivity may not be adequate, or may need re-calibration. (Detection

equipment shall be calibrated in a refrigerant-free area.)

– Ensure that the detector is not a potential source of ignition and is suitable

for the refrigerant used.

– Leak detection equipment shall be set at a percentage of the LFL of the

refrigerant and shall be calibrated to the refrigerant employed and the

appropriate percentage of gas (25 % maximum) is confirmed.

– Leak detection fluids are suitable for use with most refrigerants but the use

of detergents containing chlorine shall be avoided as the chlorine may react

with the refrigerant and corrode the copper pipe-work.

– If a leak is suspected, all naked flames shall be removed/ extinguished.

– If a leakage of refrigerant is found which requires brazing, all of the

refrigerant shall be recovered from the system, or isolated (by means of shut

off valves) in a part of the system remote from the leak.

– Oxygen free nitrogen (OFN) shall then be purged through the system both

before and during the brazing process.

12.Removal and evacuation

When breaking into the refrigerant circuit to make repairs – or for any other

purpose – conventional procedures shall be used.

However, it is important that best practice is followed since flammability is a

consideration.

The following procedure shall be adhered to:

– Remove refrigerant;

– Purge the circuit with inert gas;

Safety precautions

9

CAUTION

– Evacuate;

– Purge again with inert gas;

– Open the circuit by cutting or brazing.

The refrigerant charge shall be recovered into the correct recovery cylinders.

The system shall be “flushed” with OFN to render the unit safe.

This process may need to be repeated several times.

Compressed air or oxygen shall not be used for this task.

Flushing shall be achieved by breaking the vacuum in the system with OFN and

continuing to fill until the working pressure is achieved, then venting to

atmosphere, and finally pulling down to a vacuum.

This process shall be repeated until no refrigerant is within the system. When

the final OFN charge is used, the system shall be vented down to atmospheric

pressure to enable work to take place.

This operation is absolutely vital if brazing operations on the pipe-work are to

take place.

Ensure that the outlet for the vacuum pump is not close to any ignition sources

and there is ventilation available.

13.Charging procedures

In addition to conventional charging procedures, the following requirements

shall be followed:

– Ensure that contamination of different refrigerants does not occur when

using charging equipment.

– Hoses or lines shall be as short as possible to minimise the amount of

refrigerant contained in them.

– Cylinders shall be kept upright.

– Ensure that the refrigeration system is earthed prior to charging the system

with refrigerant.

– Label the system when charging is complete (if not already).

– Extreme care shall be taken not to overfill the refrigeration system.

Prior to recharging the system it shall be pressure tested with OFN.

The system shall be leak tested on completion of charging but prior to

commissioning.

A follow up leak test shall be carried out prior to leaving the site.

14.Decommissioning

Before carrying out this procedure, it is essential that the technician is

completely familiar with the equipment and all its detail.

It is recommended good practice that all refrigerants are recovered safely.

Prior to the task being carried out, an oil and refrigerant sample shall be taken in

case analysis is required prior to re-use of reclaimed refrigerant. It is essential

that electrical power is available before the task is commenced.

a) Become familiar with the equipment and its operation.

b) Isolate system electrically.

Safety precautions

10

CAUTION

c) Before attempting the procedure ensure that:

– Mechanical handling equipment is available, if required, for handling

refrigerant cylinders;

– All personal protective equipment is available and being used correctly;

– The recovery process is supervised at all times by a competent person;

– Recovery equipment and cylinders conform to the appropriate standards.

d) Pump down refrigerant system, if possible.

e) If a vacuum is not possible, make a manifold so that refrigerant can be

removed from various parts of the system.

f) Make sure that cylinder is situated on the scales before recovery takes

place.

g) Start the recovery machine and operate in accordance with manufacturer's

instructions.

h) Do not overfill cylinders. (No more than 80 % volume liquid charge).

I ) Do not exceed the maximum working pressure of the cylinder, even

temporarily.

j ) When the cylinders have been filled correctly and the process completed,

make sure that the cylinders and the equipment are removed from site

promptly and all isolation valves on the equipment are closed off.

k) Recovered refrigerant shall not be charged into another refrigeration system

unless it has been cleaned and checked.

15.Labelling

Equipment shall be labelled stating that it has been de-commissioned and emptied

of refrigerant.

The label shall be dated and signed.

Ensure that there are labels on the equipment stating the equipment contains

flammable refrigerant.

16.Recovery

When removing refrigerant from a system, either for servicing or

decommissioning, it is recommended good practice that all refrigerants are

removed safely.

When transferring refrigerant into cylinders, ensure that only appropriate

refrigerant recovery cylinders are employed.

Ensure that the correct number of cylinders for holding the total system charge

is available.

All cylinders to be used are designated for the recovered refrigerant and

labelled for that refrigerant (i.e. special cylinders for the recovery of

refrigerant).

Cylinders shall be complete with pressure relief valve and associated shut-

off valves in good working order.

Empty recovery cylinders are evacuated and, if possible, cooled before

recovery occurs.

The recovery equipment shall be in good working order with a set of

Safety precautions

11

CAUTION

instructions concerning the equipment that is at hand and shall be suitable for

the recovery of flammable refrigerants.

In addition, a set of calibrated weighing scales shall be available and in good

working order.

Hoses shall be complete with leak-free disconnect couplings and in good

condition.

Before using the recovery machine, check that it is in satisfactory working

order, has been properly maintained and that any associated electrical

components are sealed to prevent ignition in the event of a refrigerant release.

Consult manufacturer if in doubt.

The recovered refrigerant shall be returned to the refrigerant supplier in the

correct recovery cylinder, and the relevant Waste Transfer Note arranged.

Do not mix refrigerants in recovery units and especially not in cylinders.

If compressors or compressor oils are to be removed, ensure that they have

been evacuated to an acceptable level to make certain that flammable

refrigerant does not remain within the lubricant.

The evacuation process shall be carried out prior to returning the compressor

to the suppliers.

Only electric heating to the compressor body shall be employed to accelerate

this process.

When oil is drained from a system, it shall be carried out safely.

CAUTION

When moving or relocating the air conditioner, consult experienced service

technicians for disconnection and reinstallation of the unit.

Do not place any other electrical products or household belongings under

indoor unit or outdoor unit. Condensation dripping from the unit might get them

wet, and may cause damage or malfunction of your property.

Do not use means to accelerate the defrosting process or to clean, other than

those recommended by the manufacturer.

The appliance shall be stored in a room without continuously operating ignition

sources(for example, open flames, an operating gas appliance or an operating

electric heater).

Do not pierce or burn.

Be aware that refrigerants may not contain an odor.

To keep ventilation openings clear of obstruction.

The appliance shall be stored in a well-ventilated area where the room size

corresponds to the room area as specified for operation.

The appliance shall be stored in a room without continuously operating open

flames (for example an operating gas appliance) and ignition sources (for

example an operating electric heater).

Safety precautions

WARNING

This symbol shows that this appliance uses a flammable

refrigerant.

If the refrigerant is leaked and exposed to an external

ignition source, there is a risk of fire

CAUTION

This symbol shows that the operation manual should be

read carefully.

CAUTION

This symbol shows that a service personnel should be

handling this equipment with reference to the

installation manual.

CAUTION

This symbol shows that information is available such as

the operating manual or installation manual.

12

CAUTION

Any person who is involved with working on or breaking into a refrigerant circuit

should hold a current valid certificate from an industry-accredited assessment

authority, which authorises their competence to handle refrigerants safely in

accordance with an industry recognised assessment specification.

Servicing shall only be performed as recommended by the equipment

manufacturer.

Maintenance and repair requiring the assistance of other skilled personnel

shall be carried out under the supervision of the person competent in the use of

flammable refrigerants.

Do not use means to accelerate the defrosting process or to clean, other than

those recommended by the manufacturer.

Appliance shall be installed, operated and stored in a room with a floor

2

arealarger than 10 m .

The installation of pipe-work shall be kept to a a room with a floor area larger

2

than 10 m .

The pipe-work shall be complianced with national gas regulations.

The maximum refrigerant charge amount is 2.5 kg.The specific refrigerant

charge is based on the nameplate of the outdoor unit.

Mechanical connectors used indoors shall comply with ISO 14903. When

mechanical connectors are reused indoors, sealing parts shall be renewed.

When flared joints are reused indoors, the flare part shall be re-fabricated.

The installation of pipe-work shall be kept to a minimum.

Mechanical connections shall be accessible for maintenance purposes.

Explanation of symbols displayed on the indoor unit or outdoor unit.

Caution, risk of fire

C

13

Installation instructions

Installation diagram

Above figure is only a simple presentation of the unit, it may not match the external appearance of the unit you purchased.

Installation must be performed in accordance with the national wiring standards by authorized personnel only.

Air intake distance from

the wall should be

over 250mm

Air intake distance from the wall

over 250mm

air outlet distance from the wall

should be over 500mm

should be over 250mm

outdoor unit

Distance from the obstacle

should be over 500mm.

14

Installation instructions

Select the installation locations

Location for Installing Outdoor Unit

Where it is convenient to install and well ventilated.

Avoid installing it where flammable gas could leak.

Keep the required distance apart from the wall.

The pipe length between indoor and outdoor unit should be notmore than 5 meters in factory default

status, but it can go up to maximum 20 meters with additional refrigerant charge.

A fixed base where it is not subject to increased operation noise.

Where there is not any blockage of the air outlet.

Keep the outdoor unit away from greasy dirt,vulcanization gas exit.

Avoid installing it by the roadside where there is a risk of muddy water.

Avoid installing under direct sunlight, in an aisle or sideway, or near heat sources and ventilation fans.

Keep away from flammable materials, thick oil fog, and wet or uneven places.

Outdoor unit

Indoor unit

Pipe length is

20 meters Max.

be less than 15m

Height should

Outdoor unit

Indoor unit

Pipe length is

20 meters Max.

be less than 15m

Height should

If the height or pipe length is out of the scope of the table, please consult the merchant.

Model

7K~12K515 820

Max. allowed pipe length

without additional

refrigerant (m)

Limit of

length (m)

pipe Limit of Elevation

Difference H (m)

Required amount of

additional refrigerant (g/m)

18K

21K~25K

520 1520

520 1530

15

Outdoor Unit

1) Remove the access door from the unit by loosening

the screw. Connect the wires to the terminals on the

control board individually as follows.

2) Secure the power cord onto the control

board with cable clamp.

3) Reinstall the access door to the original position

with the screw.

4) Use a recognized circuit breaker for 24K model between

the power source and the unit. A disconnecting device to

adequately disconnect all supply lines must be fitted.

Note: For some models, it is necessary to remove the cabinet to

connect to the indoor unit terminal.

Access door

Terminal(inside)

Outdoor unit

Installation instructions

Caution:

1. Never fail to have an individual power circuit specifically for the air conditioner. As for the method of

wiring, refer to the circuit diagram posted on the inside of the access door .

2. Comfirm that the cable thickness is as specified in the power source specification.

3. Check the wires and make sure that they are all tightly fastened after cable connection.

4. Be sure to install an earth leakage circuit breaker in wet or moist areas.

The figures in this manual are based on the external

view of a standard model. Consequently, the shape

may differ from that of the air conditioner you have

selected.

Capacity (Btu/h) Power connecting cord

Power cord

Type Type

Normal cross

- sectional area

Normal cross

- sectional area

Cable Specifications

Attention:

The plug must be accessible even after the installation of the appliance in case there is a need to

disconnect it. If not possible, connect appliance to a double-pole switching device with contact

separation of at least 3 mm placed in an accessible position even after installation.

7K,9K,12K H07RN-F 2

1.0mm X3 H07RN-F 2

1.0mm X5

18K

24K

H07RN-F

2

1.5mm X3

2

2.5mm X3

H07RN-F

2

1.5mm X5

2

2.5mm X5

Connecting of the Cable

16

Installation instructions

Make sure that the color of the wires in the outdoor unit and terminal No. are the same as those

of the indoor unit.

7K~24K Model

Wiring diagram

2(N)

1(L)

0(L) 0(L)

2(N)

1(L)

Power connecting cord

Blue

Yellow/Green

Brown

Gray

Power supply

L

N

BN

BU

YE/GN

Terminal

Indoor unit

Terminal

Outdoor unit

4(SI)

Black

Warning:

Before obtaining access to terminals,all supply circuits must be disconnected.

The air which contains moisture remaining in the refrigeration cycle may cause a malfunction on the

compressor. After connecting the indoor and outdoor units, release air and moisture from the refrigerant

cycle using a vacuum pump, as shown below.

Installation instructions

Air purging

Note: To protect the environment, be sure not to discharge the refrigerant to the air directly.

See next page for air purging steps.

Fix with bolts and nuts tightly on a flat and strong floor.

If installed on the wall or roof, make sure to fix the supporter well to prevent it

from shaking due to serious vibration or strong wind.

3. Outdoor Unit Piping Connection

4. Outdoor Unit Cable Connection (see previous page)

Remove the valve caps from the 2-way and 3-way valve.

Connect the pipes to the 2-way and 3-way valves separately according to the required torque.

2. Install and Fix Outdoor Unit

1. Install Drain Port and Drain Hose (for heat-pump model only)

Drain hose

(prepared by user)

Washer

Drain port

The condensate drains from the outdoor unit when the unit operates

in heating mode. In order not to disturb your neighbor and protect

the environment, install a drain port and a drain hose to direct the

condensate water. Just install the drain port and rubber washer to

the chassis of the outdoor unit, then connect a drain hose to the

port as the right figure demonstrates.

Outdoor unit installation

Rubber pad (optional)

Place under the leg pedestal

17

Refrigerant flow direction 2-way valve

(6) Open 1/4 turn

valve cap

(1) Turn

(8) Tighten

(2) Turn

3-way valve

(8) Tighten

(1) Turn

(7) Turn to fully open the

valve

(7) Turn to fully open the valve

(8) Tighten

3-way valve diagram

connect to indoor unit

open position

spindle

service port cap

Service

port

Connect to outdoor unit

Valve core

needle

indoor unit

Valve cap

Vacuum pump

(1) Unscrew and remove caps from 2 and 3-way valves.

(2) Unscrew and remove cap from service valve.

(3) Connect vacuum pump flexible hose to the service valve.

(4) Start vacuum pump for 10-15 minutes until reaching a vacuum of 10 mm Hg absolutes.

(5) With vacuum pump still running close the low pressure knob on vacuum pump manifold. Then stop

the vacuum pump.

(6) Open 2-way valve ,1/4 turn, then close it after 10 seconds. Check tightness of all joints using liquid

soap or an electronic leak detector.

(7) Turn 2 and 3-way valves stem to fully open the valves. Disconnect the flexible vacuum pump hose.

(8) Replace and tighten all valve caps.

How to Purge Air Tubes:

Installation instructions

18

La pagina sta caricando ...

Hisense R32 Air Conditioner Manuale utente

Hisense R32 Air Conditioner Manuale utente

in altre lingue

Altri documenti