Simplicity MANUAL, OPS, ESLT23460 Manuale utente

Safety Instructions & Operator's Manual for

NOTE: Specifications are correct at time of printing and are subject to change without notice.

* Actual sustained engine power will likely be lower due to operating limitations and environmental factors. Please refer to “Engine Power Rating Information” for

further details.

Manual No. 7104355 (Rev. ‘-’, 3/10/2010)

LAWN TRACTOR

SERIES 0

Models

ESLT23460 (7800342E)

!

Not for

Reproduction

Thank you for purchasing this quality-built Snapper product. We are pleased that you’ve placed your confidence in the Snapper

brand. When operated and maintained according to the instructions in this manual, your Snapper mower will provide many

years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with mowers and how to

avoid them. Because Snapper does not necessarily know all the applications this mower could be used for, it is important that

you read and understand these instructions. Save these original instructions for future reference.

This mower requires final assembly before use. Refer to the

Assembly

section of this manual for instructions on final

assembly procedures. Follow the instructions completely.

Where to Find Us

You never have to look far to find Briggs & Stratton support and service for your mower. There are over 30,000 Briggs &

Stratton authorized service dealers worldwide who provide quality service. You can also contact Snapper Customer Service at

1-800-935-2967, or on the Internet at www.snapper.com.

Mower

Model Number _____________________________________

Serial Number _____________________________________

Engine

Model _____________________________________

Type _____________________________________

Trim _____________________________________

Date Purchased

Briggs & Stratton Yard Power Products Group

SNAPPER is a trademark of

Briggs & Stratton Power Products Group, LLC

Jefferson, WI, USA.

Not for

Reproduction

Table of Contents

Operator Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Important Operator Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

International Pictorials. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Parts Bag - Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Installing the Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Assembling the Steering Wheel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Maintenance Free Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

IMPORTANT! Before You Start Mowing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Features and Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Attachments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Using Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Driving and Stopping the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Mowing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Engine Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Maintenance Schedule. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

General Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Maintenance Free Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Lubrication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Mower Deck Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Misc. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Warranties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

General Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

3

English Dansk Nederlands Deutsch Italiano Lietuvių Norsk Polski Русский Slovenščina

Not for

Reproduction

4www.snapper.com

! !

WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects

that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in

serious injury or death to the operator or other persons. The owner of the machine must understand these

instructions and must allow only persons who understand these instructions to operate machine. Each

person operating the machine must be of sound mind and body and must not be under the influence of any

substance, which might impair vision, dexterity or judgment. If you have any questions pertaining to your

machine which your dealer cannot answer to your satisfaction, call or write the Customer Service

Department at SNAPPER, McDonough, Georgia 30253. Phone: (1-800-935-2967).

Protection for Children

Tragic accidents can occur if the operator is not alert to the

presence of children. Children are often attracted to the

machine and the mowing activity. Children who have been

given rides in the past may suddenly appear in the mowing

area for another ride and be run over or backed over by the

machine. Never assume that children will remain where you

last saw them.

1. KEEP children out of the mowing area and under the

watchful care of a responsible adult other than the operator.

2. DO NOT allow children in yard when machine is operated

(even with the blade OFF).

3. DO NOT allow children or others to ride on machine,

attachments or towed equipment (even with the blades

OFF). They may fall and be seriously injured.

4. DO NOT allow pre-teenage children to operate machine.

5. ALLOW only responsible adults & teenagers with mature

judgment under close adult supervision to operate machine.

6. DO NOT operate blades in reverse. STOP BLADES. LOOK

and SEE behind and down for children, pets and hazards

before and while backing.

7. USE EXTRA CARE when approaching blind corners,

shrubs, trees, or other objects that may obscure vision.

Protection against Tipovers

Slopes are a major factor related to loss-of-control and tip-

over accidents, which can result in severe injury or death.

All slopes require extra CAUTION. If you cannot back up the

slope or if you feel uneasy on the slope, DO NOT mow it.

Use extra care with grass catchers or other attachments;

these affect the handling and the stability of the machine.

1. DO NOT operate machine on slopes exceeding 10

degrees (18% grade).

2. Exercise EXTREME CAUTION on all slopes. Turn blades

OFF when traveling uphill. Use a slow speed and avoid

sudden or sharp turns.

3. DO NOT operate machine back and forth across face of

slopes. Operate up and down. Practice on slopes with

blades off.

4. AVOID starting, stopping or turning on slopes. If

machine stops going uphill or tires lose traction, turn

blades OFF and back slowly straight down the slope.

5. STAY ALERT for holes and other hidden hazards. Tall

grass can hide obstacles. Keep away from ditches,

washouts, culverts, fences and protruding objects.

Protection against Tipovers

(Continued From Previous Column)

6. KEEP A SAFE DISTANCE (at least 3 feet [91,4 cm]) away

from edge of ditches and other drop offs. The machine

could turn over if an edge caves in.

7. Always begin forward motion slowly and with caution.

8. Use weights or a weighted load carrier in accordance

with instructions supplied with a grass catcher. DO NOT

operate machine on slopes exceeding 10 degrees (18%

grade) when equipped with grass catcher.

9. DO NOT put your foot on the ground to try to stabilize

the machine.

10. DO NOT operate machine on wet grass. Reduced

traction could cause sliding.

11. Choose a low enough speed setting so that you will not

have to stop or shift on a slope. Tires may lose traction on

slopes even though the brakes are functioning properly.

12. DO NOT operate machine under any condition where

traction, steering or stability is doubtful.

13. Always keep the machine in gear when going down

slopes. DO NOT shift to neutral (or actuate hydro roll

release) and coast downhill.

Preparation

1. Read, understand, and follow instructions and warnings

in this manual and on the machine, engine and

attachments. Know the controls and the proper use of the

machine before starting.

2. Only mature, responsible persons shall operate the

machine and only after proper instruction.

3. Data indicates that operators age 60 and above, are

involved in a large percentage of mower-related injuries.

These operators should evaluate their ability to operate the

mower safely enough to protect themselves and others

from serious injury.

4. Handle fuel with extra care. Fuels are flammable and

vapors are explosive. Use only an approved fuel container.

DO NOT remove fuel cap or add fuel with engine running.

Add fuel outdoors only with engine stopped and cool. Clean

spilled fuel from machine. DO NOT smoke.

5. Practice operation of machine with BLADES OFF to learn

controls and develop skills.

6. Check the area to be mowed and remove all objects such

as toys, wire, rocks, limbs and other objects that could

cause injury if thrown by blade or interfere with mowing.

Important Operator Safety Instructions

Not for

Reproduction

5

! !

Protection against Tipovers

(Continued From Previous Column)

7. Keep people and pets out of mowing area. Immediately

STOP blades, STOP engine, and STOP machine if anyone

enters the area.

8. Check shields, deflectors, switches, blade controls and

other safety devices frequently for proper operation and

location.

9. Make sure all safety decals are clearly legible. Replace if

damaged.

10. Protect yourself when mowing and wear safety glasses,

a dust mask, long pants and substantial footwear.

11. Know how to STOP blades and engine quickly in

preparation for emergencies.

12. Use extra care when loading or unloading the machine

into a trailer or truck.

13. Check grass catcher components frequently for signs of

wear or deterioration and replace as needed to prevent

injury from thrown objects going through weak or worn

spots.

Safe Handling of Gasoline

To avoid personal injury or property damage, use extreme

care in handling gasoline. Gasoline is extremely flammable

and the vapors are explosive.

1. Extinguish all cigarettes, cigars, pipes and other sources

of ignition.

2. Use only an approved fuel container.

3. DO NOT remove fuel cap or add fuel with the engine

running. Allow the engine to cool before refueling.

4. DO NOT refuel the machine indoors.

5. DO NOT store the machine or fuel container inside where

there is an open flame, spark or pilot light such as on a

water heater or other appliances.

6. DO NOT fill fuel containers inside a vehicle or on a truck

or trailer bed with a plastic liner. Always place the

containers on the ground away from the vehicle before

filling.

7. Remove gas-powered equipment from the vehicle or

trailer and refuel it on the ground. If this is not possible,

then refuel equipment using a portable container, rather

than a gasoline dispenser nozzle.

8. DO NOT start gas powered equipment in enclosed

vehicles or trailers.

9. Keep the nozzle in contact with the rim of the fuel tank or

container opening at all times until fueling is complete. DO

NOT use a nozzle lock-open device.

10. If fuel is spilled on clothing, change clothing

immediately.

11. Never overfill a fuel tank. Replace fuel cap and tighten

securely.

Operation

1. Mount and dismount machine from left side. Keep clear

of discharge opening at all times.

2. Start engine from operator’s seat, if possible. Make sure

blades are OFF and parking brake is set.

3. DO NOT leave machine with engine running. STOP

engine, STOP blades, SET brake, and remove key before

leaving operators position of any reason.

4. DO NOT operate machine unless properly seated with

feet on feet rests or pedal(s).

5. STOP BLADES and ENGINE and make sure blades have

stopped before removing grass catcher or unclogging

mower to prevent loss of fingers or hand.

6. Blades must be OFF except when cutting grass. Set

blades in highest position when mowing over rough

ground.

7. Keep hands and feet away from rotating blades

underneath deck. DO NOT place foot on ground while

BLADES are ON or machine is in motion.

8. DO NOT operate machine without entire grass catcher or

guards in place and working. DO NOT point discharge at

people, passing cars, windows or doors.

9. Slow down before turning.

10. Watch out for traffic when near or crossing roadways.

11. STOP engine immediately after striking an obstruction.

Inspect machine and repair damage before resuming

operation.

12. Operate machine only in daylight or with good artificial

light.

13. Exercise CAUTION when pulling loads. Limit loads to

those you can safely control and attach loads to hitch plate

as specified with SNAPPER attachment instructions.

14. On slopes, the weight of the towed equipment may

cause loss of traction and loss of control. When towing,

travel slowly and allow extra distance to stop.

15. DO NOT operate engine in enclosed areas. Engine

exhaust gases contain carbon monoxide, a deadly poison.

16. DO NOT discharge material against a wall or

obstruction. Material may ricochet back towards the

operator.

17. Only use accessories approved by the manufacturer.

See manufacturer’s instructions for proper operation and

installation of accessories.

Important Operator Safety Instructions (Continued)

Not for

Reproduction

6www.snapper.com

! !

Towing

1. Tow only with a machine that has a hitch designed for

towing. DO NOT attach towed equipment except at the hitch

point.

2. Follow the manufacturer’s recommendation for weight

limits for towed equipment and towing on slopes.

3. DO NOT allow children or others on towed equipment.

4. On slopes, the weight of the towed equipment may cause

loss of traction and loss of control.

5. Travel slowly and allow extra distance to stop.

Maintenance

1. DO NOT store machine or fuel container inside where

fumes may reach an open flame, spark or pilot light such as

in a water heater, furnace, clothes dryer or other gas

appliance. Allow engine to cool before storing machine in

an enclosure. Store fuel container out of the reach of

children in a well ventilated, unoccupied building.

2. Keep engine free of grass, leaves or excess grease to

reduce fire hazard and engine overheating.

3. When draining fuel tank, drain fuel into an approved

container outdoors and away from open flame.

4. Check brakes frequently; adjust, repair or replace as

needed.

5. Keep all bolts, nuts and screws properly tight. Check that

all cotter pins are in proper position.

Maintenance

(Continued From Previous Column)

6. Always provide adequate ventilation when running

engine. Exhaust gases contain carbon monoxide, an

odorless and deadly poison.

7. Disconnect negative (black) cable from battery before

performing maintenance or service. Cranking engine could

cause injury.

8. DO NOT work under machine without safety blocks.

9. Service engine and make adjustments only when engine

is stopped. Remove spark plug wire(s) from spark plug(s)

and secure wire(s) away from spark plug(s).

10. DO NOT change engine governor speed settings or

overspeed engine.

11. Lubricate machine at intervals specified in manual to

prevent controls from binding.

12. Mower blades are sharp and can cut. Wrap the blades

or wear heavy leather gloves and use CAUTION when

handling them.

13. DO NOT test for spark by grounding spark plug next to

spark plug hole; spark plug could ignite gas exiting engine.

14. Have machine serviced by an authorized SNAPPER

dealer at least once a year and have the dealer install any

new safety devices.

15. Maintain or replace safety and instruction labels as

necessary.

16. Use only genuine SNAPPER replacement parts to

assure that original standards are maintained.

Important Operator Safety Instructions (Continued)

Not for

Reproduction

International Pictorials

IMPORTANT: Some of the following pictorials are located on your unit or on literature supplied with the product. Before you

operate the unit, learn and understand the purpose for each pictorial.

Figure 1: Safety warning pictorials

ABCDE

GH

F

IJK

LMNP

max 10°

A - Warning.

B - Shield Eyes. Explosive Gases Can

Cause Blindness Or Injury.

C - No Sparks, Flames or Smoking.

D - Sulphuric Acid Can Cause Blindness

Or Severe Burns.

E - Flush Eyes Immediately With Water.

Get Medical Help Fast.

F - IMPORTANT: Read Owner’s Manual

Before Operating This Machine.

G - WARNING: Thrown Objects. Keep

Bystanders Away. Read User

Instructions Before Operating This

Machine.

H - WARNING: Do Not Use This

Machine On Slopes Greater Than 10

Degrees.

I - DANGER: Keep People, Especially

Children, Away From Unit.

J - DANGER: No Step.

K - DANGER: Keep Feet And Hands

Away From Rotating Blade.

L- DANGER: Keep Hands Away From

Rotating Blade.

M - DANGER: Disconnect Spark Plug

Wire Before Servicing Unit.

N - WARNING: Hot Surface.

O - WARNING: Use Caution When

Connecting Or Disconnecting

Accessories.

P - WARNING: Crushed Fingers.

A - Engine start

B - Lights

C - Engine off

D - Engine on

E - Brake

F - Parking brake

G - Clutch

H - Slow

I - Fast

J - Choke

K - Oil

L - Blade rotation control

M - Raise

N - Fuel

ABCDEGH

F

IJKLMN

max± 90N max± 150N

O

Figure 2: Control and operating pictorials

7

Not for

Reproduction

Assembly

Read and follow the assembly and adjustment

instructions for your mower.

All fasteners are in the parts bag. Do not discard

any parts or material until the unit

is assembled.

NOTE: In this instruction book, left and right describe the

location of a part with the operator on the seat.

WARNING: Before doing any assembly or

maintenance to the mower, remove the wire from

the spark plug.

8www.snapper.com

Parts Bag - Contents

The fasteners and other loose parts are shown below. The

fasteners are shown full size. The quantity is shown in

brackets ( ).

Figure 3: Parts bag components

A - (2) Carriage bolt

B - (2) Wing nut

C - (1) Bolt

D - (1) Washer

E - (2) Knob

F - (2) Washer

G - (1) Keys & ring

H - (1) Terminal cover

ABC

D

EG

H

F

Not for

Reproduction

Installing the Seat

How to Install the Seat

1. Carefully remove the plastic bag from the seat. Use the

fasteners shown below to install the seat. The fasteners

are shown at full size.

Figure 4: Seat parts

A - Wing bolt (Also see “E” in Figure 3)

B - Washer (Also see “F” in Figure 3)

NOTE: Fasteners may be attached to seat for shipping

purposes, if so remove fasteners before proceeding.

2. Align the holes in the seat hinge to the holes in the

seat (Figure 5). Fasten the seat to the seat hinge with

the fasteners as shown.

3. Check the operating position of the seat. If the seat

needs to be adjusted, loosen the two wing bolts. Slide

the seat forward or backward along the seat adjusting

holes as shown. Tighten the wing bolts (A).

Figure 5: Seat

A - Wing bolt

B - Washer

C - Seat adjusting hole

D - Seat hinge

E - Seat

Assembling the Steering Wheel

How to Assemble the Steering Wheel

Tools Required: 3/8" Socket Wrench

Attach the steering wheel as follows:

Figure 6: Steering wheel parts

A - Screw (Also see “C” in Figure 3)

B - Washer (Also see “D” in Figure 3)

1. Make sure the front wheels point forward.

2. Slide the bellows over the steering post

(Figure 7).

NOTE: Before attachment of the steering wheel, make

sure that the front wheels point forward and are

straight. For proper alignment of the steering wheel,

see Figure 7.

3. Slide the steering wheel onto the steering post.

4. Use the fasteners shown above to secure the steering

wheel. The fasteners are shown at full size. Tighten the

screw until snug and then add 1/4 turn. DO NOT over

tighten.

5. Attach the cover to the steering wheel.

6. Some models have an

optional

decal in the parts bag.

Attach the decal to the center of the steering wheel as

shown.

A B

A

B

C

D

E

A

9

Not for

Reproduction

Figure 7: Steering post

A - Screw

B - Washer

C - Cover

D - Decal (Optional)

E - Steering wheel

F - Bellows

G - Steering post

H - Straight

Maintenance Free Battery

IMPORTANT: Before you attach the battery cables to the

battery, check the battery date. The battery date tells if the

battery must be charged.

1. Check the top and the side of the battery for the

location of the battery date (Figure 9).

2. If the battery is put into service before the battery date,

the battery cables can be attached without charging the

battery. See “How To Install The Battery Cables”.

3. If the battery is put into service

after

the battery date,

the battery must be charged. See “How To Charge The

Maintenance Free Battery”.

How to Charge the Maintenance Free Battery

WARNING: When you charge the battery, do not

smoke. Keep the battery away from any sparks. The

fumes from the battery acid can cause an

explosion.

1. Remove the battery and battery tray.

2. Remove the protective cap from the battery terminal.

3. Use a 12 volt battery charger to charge the battery.

Charge at a rate of 6 amperes for one hour. If you do

not have a battery charger, have an authorized service

center charge the battery.

4. Install the battery and battery tray. Make sure the

positive (+) terminal is on the left side.

How to Install the Battery Cables

WARNING: To prevent sparks, fasten the red cable

to the positive (+) terminal before you connect the

black cable.

Use the fasteners shown below to install the battery cables.

The fasteners are shown at full size.

Figure 8: Battery cable parts

A - Carriage bolt (Also see “A” in Figure 3)

B - Wing nut (Also see “B” in Figure 3)

10 www.snapper.com

D

A

B

E

C

H

G

F

AB

Not for

Reproduction

1. Remove the protective cap from the battery terminal.

2. Fasten the red cable and terminal cover (if equipped)

to the positive (+) terminal with the fasteners as

shown (Figure 9).

3. Fasten the black cable to the negative (-) terminal with

the fasteners as shown.

Figure 9: Battery

A - Carriage bolt

B - Wing nut

C - Black cable

D - Positive (+) terminal

E - Red cable

F - Battery

G - Battery tray

H - Terminal cover (Also see “H” in Figure 3)

IMPORTANT! Before You Start Mowing

• Check the engine oil.

• Fill the fuel tank with gasoline.

• Check the air pressure of the tires.

• Check the level of the mower deck.

• Make sure the battery cables are attached.

• Make sure the wire is attached to the spark plug.

WARNING: Before doing any assembly or

maintenance to the mower, remove the wire from

the spark plug.

NOTE: In this instruction book, left and right describe the

location of a part with the operator on the seat.

Operator Presence System (Seat)

The seat has an Operator Presence System to shut off the

engine when the operator leaves the seat. This system is not

intended for regular use in stopping the engine or the

blade(s). Before leaving the seat, move the blade rotation

control to the DISENGAGE position, shift to neutral, set the

parking brake, and stop the engine.

How To Check The Safety Interlock Switches

To check the function of the safety interlock switches, follow

the steps below.

1. Check the blade rotation control switch. Sit in the seat.

Depress the clutch/brake pedal. Move the blade rotation

control to the ENGAGE position. Turn the ignition

switch to the START position. The engine should not

start. If the engine starts, the switch is defective and

must be replaced.

2. Check the clutch/brake switch. Sit in the seat. Move the

blade rotation control to the DISENGAGE position. DO

NOT depress the clutch/brake pedal. Turn the ignition

switch to the START position. The engine should not

start. If the engine starts, the switch is defective and

must be replaced.

3. Check the Operator Presence System switch. DO NOT

sit in the seat. Depress the clutch/brake pedal. Move

the blade rotation control to the DISENGAGE position.

Turn the ignition switch to the START position. The

engine should not start. If the engine starts, the switch

is defective and must be replaced.

4. Check the Reverse Mowing Option (RMO) switch. Sit

in the seat. Depress the clutch/brake pedal. Move the

blade rotation control to the DISENGAGE position. Start

the engine and move the drive control to the reverse

(R) position. With the engine running, move the blade

rotation control to the ENGAGE position. The engine

should stop running. If the engine continues to run, the

RMO switch is defective and must be replaced.

11

H

A

E

A

B

D

C

G

F

Not for

Reproduction

How to Prepare the Engine

NOTE: The engine was shipped from the factory filled with

oil. Check the level of the oil. Add oil as needed.

NOTE: The operation of a new engine will sometimes result

in a slight amount of smoke. This smoke is caused by paint

or oil on or around the muffler. This is normal and only

expected during initial operation.

A separate engine manual is also included with the unit. See

this engine manual for the manufacturer’s instructions for

the type of gasoline and oil to use. Before you use the unit,

read the information on safety, operation, maintenance, and

storage.

WARNING: Follow the engine manufacturer’s

instructions for the type of gasoline and oil to use.

Always use a safety gasoline container. Do not

smoke when adding gasoline to the engine. When

inside an enclosure, do not fill with gasoline.

Before you add gasoline, stop the engine. Let the

engine cool for several minutes.

IMPORTANT: This unit is equipped with an internal

combustion engine and must not be used on or near any

unimproved forest-covered, brush-covered or grass-covered

land unless the engine’s exhaust system is equipped with a

spark arrester meeting applicable local or state laws (if any).

If a spark arrester is used, it must be maintained in effective

working order by the operator.

In the State of California the above is required by law

(Section 4442 of the California Public Resources Code).

Other states may have similar laws. Federal laws apply on

federal lands. See an Authorized Service Center for a spark

arrester for the muffler.

In some areas, local law requires the use of a resistor spark

plug to control the ignition signals. See an Authorized

Service Center for a resistor spark plug for the engine.

NOTE: Actual sustained horsepower will likely be lower due

to operating limitations and environmental factors.

Check the Tires

NOTE: The tires may be over inflated for shipment.

Check the air pressure in the tires. Tires with too much air

pressure will cause the unit to ride rough. Also, the wrong

air pressure will keep the mower deck from cutting level.

Recommended air pressure is 14 PSI (1 BAR).

Check the Level of the Mower Deck

Make sure the level of cut is still correct. After you mow a

short distance, look at the area that was cut. If the mower

deck does not cut level, see the instructions on “How To

Level The Mower Deck” in the Maintenance section of this

instruction book.

12 www.snapper.com

Not for

Reproduction

Features and Controls

A - Throttle Control / Choke Control Levers — Throttle

control increases or decreases the speed of the engine.

Choke control engages the choke to start a cold engine.

B - Steering Wheel (Removed for clarity) — Steers the unit.

C - Brake Pedal — Quickly stops the unit.

D - Deck Lift Lever — Changes the height of cut.

E - PTO Switch — Starts and stops the rotation of the

blades.

F - Cruise Control — Locks ground speed in forward.

G - Reverse Mowing Option (RMO) — Allows engaging of

mowing deck while traveling in reverse.

H - Ignition Switch — Starts and stops the engine.

(Note: The headlight switch is incorporated into the

ignition switch.)

I- Parking Brake Lever — Engages the brake when you leave

the unit.

J - Speed Control Pedal — Changes the speed and the

direction of the unit.

K - Automatic Drive Disconnect (not shown, located behind

the unit) — Disengages the transmission.

13

H

I

A

C

J

E

D

F

G

B

Not for

Reproduction

Operation

Attachments

This unit can use many different attachments.

For all pull-behind attachments or trailers, the maximum

gross weight is 250 pounds (113 kg). Gross weight is the

weight of the attachment or trailer and any load that might

be on or in it.

Do not operate on a slope that is greater than 10 degrees

when using a pull-behind attachment or trailer. Never allow

someone to stand or ride on or in an attachment or trailer.

Using Controls

How to Use the Throttle Control

Use the throttle control to increase or decrease the speed of

the engine.

CAUTION: Always operate the engine with the throttle

control in the FAST position. If the engine runs for several

minutes at slower than the FAST position, the engine and

transmission will overheat and can be damaged.

1. The FAST position is marked with a detent. For normal

operation and when using a grass bagger, move the

throttle control to the FAST position. For maximum

charging of the battery and for a cooler running engine

and transmission, operate the engine in the FAST

position.

2. For transport and to tow pull behind attachments,

control the ground speed with the speed control pedal.

3. The engine governor is set at the factory for maximum

performance. Do not adjust the governor to increase

the speed of the engine.

14 www.snapper.com

Not for

Reproduction

How to Engage the Blades

The PTO switch is above and to the right of the steering

wheel (Figure 10). Use the PTO switch to engage the blades.

Figure 10: PTO switch

A - PTO switch (shown in the DISENGAGE position)

1. Before you start the engine, make sure the PTO switch

is pushed down in the DISENGAGE position.

2. Pull the PTO switch up to the ENGAGE position to

rotate the blades.

NOTE: If the engine stops when you engage the blades,

the seat switch is not activated. Make sure you sit in

the middle of the seat. Also, make sure the wire is

connected to the seat switch.

3. Push the PTO switch down to the DISENGAGE position

to stop the blades. Before you leave the operator’s

position, make sure the blades have stopped rotating.

4. Before you ride the unit across a sidewalk or a road,

push the PTO switch down to the DISENGAGE position.

WARNING: Always keep your hands and feet away

from the blade, deflector opening, and the mower

deck when the engine runs.

How to Use the Speed Control Pedal

The drive system uses a Hydrostatic Automatic Drive

transmission. The Hydrostatic transmission is very easy to

operate. This type of drive system does not require a shift

lever or a clutch pedal.

The speed and direction of travel is controlled by a single

speed control pedal operated with your right foot. Do not

use the left brake pedal in normal operation. Only use the left

brake pedal to quickly stop in an emergency.

Driving and Stopping the Unit

How to Drive Forward

1. The automatic drive disconnect must be in the DRIVE

position (Figure 13).

2. Slowly release your left foot from the brake pedal.

3. Move the throttle control to the FAST position.

4. Slowly push the speed control pedal forward to the

desired speed (Figure 11).

5. To increase forward speed, slowly move the speed

control pedal forward. To reduce forward speed, slowly

release the speed control pedal until the unit slows to

the desired speed.

Figure 11: Speed control operation

A - Reverse

B - Neutral

C - Forward

D - Forward movement

E - Reverse movement

F - Speed control pedal

15

A

ED

F

7101936

A B C

Not for

Reproduction

How to Use the Cruise Control

To engage the cruise control:

1. Slowly push the speed control pedal forward to the

desired speed (Figure 11).

2. Pull up on the cruise control knob (Figure 12). Release

the speed control pedal. The unit should continue

traveling forward at the desired speed.

NOTE: The cruise control only operates in forward

speeds.

To disengage the cruise control:

1. Push the speed control pedal (Figure 11), OR

2. Push the brake pedal.

WARNING: Do not engage the cruise control when

driving on slopes, or when people or animals are in

the vicinity.

Figure 12: Cruise control

A - Cruise Control knob

How to Drive in Reverse

1. Look to the rear.

2. Slowly push the speed control pedal to the REVERSE

position.

How to Change Direction

CAUTION: To change directions, do not use the left brake

pedal. Use only the speed control pedal.

1. Slowly remove your foot from the speed control pedal.

The speed control pedal will automatically return to the

NEUTRAL position.

2. When the unit stops, slowly move the speed control

pedal to the desired direction.

Speed Control Pedal Positions

The forward speed is controlled by the position of the speed

control pedal. The following chart provides functions along

with the pedal positions. Always operate the engine with the

throttle control in the FAST position.

How to Disconnect the Transmission

To push the unit, use the automatic drive disconnect to

release the transmission. The automatic drive disconnect is

located on the right rear of the unit.

1. The engine must be off.

2. Pull out and lock the automatic drive disconnect in the

PUSH position (Figure 13). The transmission is now

released and the unit can be pushed.

NOTE: In cold weather, the heavy viscosity oil in the

transmission will make the unit difficult to push.

3. To engage the transmission, unlock and push in the

automatic drive disconnect. The transmission is now

connected and ready to operate.

Function Pedal Positon Throttle Position

Trimming

Snow Thrower 1/3 Fast Throttle

Bagging Grass 1/3 to 1/2

Normal Mowing 1/2 to 2/3

Easy Mowing

Snow Blade 1/2 to 3/4

Transport FULL

Pull Behind

Attachments 1/3 to 1/2

16 www.snapper.com

A

Not for

Reproduction

Figure 13: Automatic drive disconnect

A - Automatic drive disconnect DRIVE position

B - Automatic drive disconnect PUSH position

C - Automatic drive disconnect

How to Set the Parking Brake

1. Completely push the brake pedal forward.

2. Lift the parking brake lever (Figure 14).

3. Remove your foot from the brake pedal and then

release the parking brake lever. Make sure the parking

brake will hold the unit.

4. To release the parking brake, completely push the brake

pedal forward. The parking brake will automatically

release.

WARNING: Before you leave the operator’s position,

move the speed control pedal to the neutral (N)

position. Set the parking brake. Move the blade

rotation control to the DISENGAGE position. Stop the

engine and remove the ignition key.

Figure 14: Parking brake

A - Brake pedal

B - Parking brake lever

How to Change the Cutting Height

To change the cutting height, raise or lower the deck lift

lever as follows:

1. Move the deck lift lever forward to lower the mower

deck and back to raise the mower deck (Figure 15).

2. When you ride on a sidewalk or road, move the deck lift

lever to the highest position and disengage the blades

(Figure 10).

Figure 15: Lift control

A - Deck lift lever

How to Stop the Unit

1. Slowly remove your foot from the speed control pedal.

The speed control pedal will automatically return to the

NEUTRAL position and the unit will stop.

2. Move the blade rotation control to the DISENGAGE

position.

3. Set the parking brake.

WARNING: Make sure the parking brake will hold

the unit.

4. Move the throttle control to the SLOW position.

5. To stop the engine, turn the ignition key to the OFF

position. Remove the key.

17

C

A

7101935

AB

B

Not for

Reproduction

How to Transport the Unit

To transport the unit, follow the steps below.

1. Disengage the blades.

2. Raise the deck lift lever to the highest position.

3. Move the throttle control to the FAST position.

4. Slowly push the speed control pedal forward to the

desired speed.

Mowing

How to Operate the Mower Deck

WARNING: The deflector is a safety device. Do not

remove the deflector. The deflector forces the

discharged material toward the ground. Always

keep the deflector in the down position. If the

deflector is damaged, replace the deflector with an

original equipment part from an authorized service

center.

1. Start the engine.

2. Release the parking brake.

3. Move the deck lift lever to a height of cut position. In

high or thick grass, cut the grass in the highest

position first and then lower the mower deck to a lower

position.

CAUTION: Do not operate with the mower deck in the

LEVEL ADJUSTMENT position. If you operate in the LEVEL

ADJUSTMENT position, the mower deck and blades can be

damaged.

4. Move the throttle control to the SLOW position.

5. Engage the blades.

6. Move the throttle control to the FAST position.

7. Slowly push the speed control pedal to the desired

speed.

NOTE: When you mow in heavy grass or mow with a

grass bagger, use a slow forward speed.

8. Make sure the level of cut set at the factory is still

correct. After you mow a short distance, look at the

area that was cut. If the mower deck does not cut level,

see the instructions on “How To Level The Mower

Deck” in the Maintenance section.

WARNING: For better control of the unit, always

select a safe speed.

Reverse Mowing Option (RMO)

WARNING: Mowing in reverse can be hazardous to

bystanders. Tragic accidents can occur if the

operator is not alert to the presence of children.

Never activate RMO if children are present.

Children are often attracted to the unit and the

mowing activity.

1. Engage the blades.

2. Insert the supplied key into the RMO switch, located to

the right of the steering wheel bellows (Figure 16).

3. Turn the key. The L.E.D. light will illuminate, indicating

thet the RMO feature has been activated. The mower

deck can now be operated while the unit is traveling in

reverse.

4. The reverse mowing option is deactivated when the

blades are disengaged, and must be reactivated each

time the blades are engaged, if desired.

5. Remove the key to restrict access to the RMO feature.

WARNING: The engine will shut off if the speed

control pedal is moved into reverse while the

blades are engaged and the RMO is not activated.

Figure 16: Reverse Mowing Option (RMO)

A - Key

B - RMO switch

C - L.E.D. light

18 www.snapper.com

A

C

B

Not for

Reproduction

How to Operate the Unit on Hills

WARNING: Do not ride up or down slopes that are

too steep to back straight up. Never ride the unit

across a slope.

1. Control the speed only with the speed control pedal. Do

not use the brake pedal on a hill.

2. To help prevent an accident, slowly move the speed

control pedal. Avoid sudden turns or changes in speed.

3. To reduce forward speed when going down a hill,

slowly release the speed control pedal until the unit

slows to the desired speed.

How to Stop on a Hill

1. Avoid stopping on a hill. If you must quickly stop in an

emergency, remove your right foot from the speed

control pedal and quickly depress the left brake pedal.

2. Set the parking brake.

3. Before you dismount from the seat, move the throttle

control to SLOW position, move the blade rotation

control to the DISENGAGED position, turn off the

engine and set the parking brake.

How to Start Operation on a Hill

1. Start the engine.

2. Move the blade rotation control to the ENGAGED

position.

3. Move the throttle control to the FAST position.

4. Depress the brake pedal and release the parking brake.

As you release the parking brake, push the speed

control pedal to the desired speed.

WARNING: Slowly push the speed control pedal as

you release the parking brake. The parking brake

must be disengaged before the speed control pedal

is able to engage the transmission.

19

Not for

Reproduction

Engine Operation

Before Starting the Engine

Check the Oil

NOTE: The engine was shipped from the factory filled with

oil. Check the level of the oil. Add oil as needed. See the

engine manufacturer’s instructions for the type of gasoline

and oil to use.

1. Make sure the unit is level.

NOTE: Do not check the level of the oil while the engine

runs.

2. Check the oil. Follow the procedure in the engine

manufacturer’s instructions.

3. If necessary, add oil until the oil reaches the FULL mark

on the dipstick. The quantity of oil needed from ADD to

FULL is shown on the dipstick. Do not add too much

oil.

Add Gasoline

WARNING: Always use a safety gasoline container.

Do not smoke when adding gasoline to the fuel

tank. Do not add gasoline when you are inside an

enclosure. Before you add gasoline, stop the

engine and let the engine cool for several minutes.

Fill the fuel tank with regular unleaded gasoline. Do not use

premium unleaded gasoline. Make sure the gasoline is fresh

and clean. Leaded gasoline will increase deposits and

shorten the life of the valves.

Figure 17: Gas tank

A - Fuel tank

B - Full line

CAUTION: A mixture of alcohol (ethanol or methanol) and

gasoline (called gasohol), will attract moisture and cause

acid deposits during storage. While the unit is in storage,

the acids in the fuel can damage the fuel system.

To prevent engine problems with the fuel system, empty the

fuel system before storage of 30 days or longer as follows.

1. Drain the fuel tank.

2. Start the engine. Let the engine run until the fuel lines

and the carburetor are empty.

3. After storage, make sure you use fresh fuel. See the

storage instructions for additional information.

4. Never use engine cleaner or carburetor cleaner in the

fuel tank or permanent damage can occur.

Carburetor

Do not attempt to adjust the carburator. Engine adjustments

and repairs should be performed only by an authorized

dealer.

How to Start the Engine

WARNING: The electrical system has an operator

presence system that includes a sensor switch for

the seat. These components tell the electrical

system if the operator is sitting on the seat. This

system will stop the engine when the operator

leaves the seat. For your protection, always make

sure this system operates correctly.

NOTE: The engine will not start unless you depress the brake

pedal or engage the parking brake and disengage the blades.

1. Push the brake pedal completely forward. Keep your

foot on the pedal.

2. Make sure the blades are disengaged.

3. Move the throttle control completely forward to the

FAST position.

4. Move the choke control completely forward.

5. Turn the ignition key to the START position. Release

the key when the engine starts.

NOTE: If the engine does not start after four or five

tries, see the TROUBLESHOOTING CHART.

6. Turn off the choke, and slowly move the throttle control

to the SLOW position.

7. Let a cold engine run for several minutes. Begin work

when the engine is warm. To start a hot engine, move

the throttle control to a position between FAST and

SLOW.

20 www.snapper.com

B

A

Not for

Reproduction

La pagina si sta caricando...

Simplicity MANUAL, OPS, ESLT23460 Manuale utente

Simplicity MANUAL, OPS, ESLT23460 Manuale utente

in altre lingue