Ericsson M-PA EDACS Manuale utente

Marca: Ericsson

Modello: M-PA EDACS

Tipo: Manuale utente

Mobile Communications

LBI-38407D

Operator’s Manual

EDACS



M-PA



PORTABLE RADIOS

May 1991, Ericsson Mobile Communications AB

Table of Contents

INTRODUCTION . . . . . . . . . 5

CONTROLS . . . . . . . . . . . 7

ON/OFF SWITCH . . . . . . . 7

VOLUME CONTROL KNOB . . 7

CONTROL KNOB . . . . . . . 7

PTT BUTTON . . . . . . . . . . 8

MONITOR BUTTON . . . . . . 8

Trunked Mode . . . . . . . . 8

Conventional Mode . . . . . . 8

EMERGENCY BUTTON . . . . 9

STEP BUTTON

(Scan And System Models Only) 9

SCAN BUTTON

(Scan And System Models Only) 10

Table of Contents

(Continued)

SPC BUTTON

(Scan And System Models Only) 10

2nd BUTTON

(Scan And System ModeIs Only) 11

ADD/DELETE BUTTON

(Scan And System Models Only) 11

LOCK BUTTON

(Scan And System ModeIs Only) 11

STO BUTTON (Shifted Digit 1 -

System Model Only) . . . . . . 11

RCL BUTTON (Shifted Digit 3 -

System Model Only) . . . . . . 12

CLR BUTTON (Shifted # Button-

System Model Only) . . . . . . 12

STS BUTTON (Shifted Digit -

System Model Only) . . . . . . 12

INDICATORS . . . . . . . . . . . 12

UNIVERSAL DEVICE

CONNECTOR . . . . . . . . . . 14

ALERT TONES . . . . . . . . . . 14

OPERATION . . . . . . . . . . . 15

POWER-UP . . . . . . . . . . 15

SYSTEM/GROUP/CHANNEL

SELECTION . . . . . . . . . . 15

This manual is published by

Ericsson GE Mobile

Communications Inc.

, without any warranty. Im-

provements and changes to this manual necessitated

by typographical errors, inaccuracies of current infor-

mation, or improvements to programs and/or equip-

ment, may be made by

Ericsson GE Mobile

Communications Inc.

, at any time and without no-

tice. Such changes will be incorporated into new

editions of this manual. No part of this manual may be

reproduced or transmitted in any form or by any

means, electronic or mechanical, including photo-

copying and recording, for any purpose, without the

express written permission of

Ericsson GE Mobile

Communications Inc.

Table of Contents

(Continued)

STEP Button Programmed For

System Selection; CONTROL

KNOB Programmed For Group

And Channel Selection . . . . 16

CONTROL KNOB Programmed

For System Selection; STEP

Button Programmed For Group

And Channel Selection . . . . 17

TRUNKED MODE OPERATION 17

Receiving A Message . . . . . 17

Sending A Message . . . . . . 19

Emergency Operation

(Trunked Mode) . . . . . . . . 19

Dynamic Regrouping . . . . . 20

Wide Area System Scanning . 20

Scanning Trunked Groups (Scan

And System Models Only) . . . 21

SpeciaI CaIIs . . . . . . . . . 22

SYSTEM MESSAGE OPERATION

(System Model Only) . . . . . . 27

CONVENTIONAL MODE

OPERATION . . . . . . . . . . . 27

Receiving A Message . . . . . 27

Sending A Message . . . . . . 28

Emergency Operation

(Conventional Mode) . . . . . 29

Scanning Conventional

Channels (Scan And System

Models Only) . . . . . . . . . . 29

Table of Contents

(Continued)

Telephone Interconnect

Calls (Scan And System

ModeIs Only) . . . . . . . . . 31

OPERATING TIPS . . . . . . . . 31

OPERATING RULES

AND REGULATIONS . . . . . . . 32

BATTERY PACKS . . . . . . . . . 33

INSTALLING THE BATTERY

PACK . . . . . . . . . . . . . . 33

REMOVING THE BATTERY

PACK . . . . . . . . . . . . . . 33

CHARGING THE BATTERY

PACKS . . . . . . . . . . . . . . 34

RECHARGEABLE BATTERY

PACK DISPOSAL . . . . . . . . 35

SWIVEL MOUNT REMOVAL AND

REPLACEMENT . . . . . . . . . . 35

INTRINSICALLY SAFE USAGE . . 36

BATTERY PACKS . . . . . . . . 36

ACCESSORIES . . . . . . . . . 37

WARRANTY . . . . . . . . . . . . 38

NICKEL-CADMIUM BATTERY

WARRANTY . . . . . . . . . . . . 39

CONTROLS

ON/OFF SWITCH

The ON/OFF SWITCH is located on

the battery pack. Sliding this switch up will

supply power to the radio from the battery

pack. An audible click will be heard and

the ‘ON" indicator will be exposed. When

the radio is turned on, it will perform a

power-up self test and resume operating

on the previous group or channel. Sliding

the switch down will turn the radio off.

VOLUME CONTROL KNOB

The VOLUME CONTROL KNOB is a

rotatable control on the top of the radio

used to adjust the receiver’s volume level

in the speaker. Rotating this knob in a

clockwise direction will increase the vol-

ume and counter-clockwise rotation will

decrease the volume. Minimum volume

levels can be programmed into the radio to

prevent missed calls when the knob is

rotated fully counter-clockwise.

CONTROL KNOB

Figure 1 - Side View (All Models)

Figure 2 - Select Model

INTRODUCTION

The EDACS M-PA Select, Scan

and System model radios are high-quality

microprocessor-controlled synthesized

two-way FM portable radios. These full-

featured radios are designed for operation

in EDACS (Enhanced Digital Access Com-

munications System) trunking systems

and conventional radio systems. M-PA op-

eration is highlighted by the radio’s pro-

gramming versatility. This permits custom

operation of each radio to meet the needs

of the radio system and the individual us-

ers.

This manual describes operating pro-

cedures for the three (3) different radio

models.

The M-PA Select model radio is the

basic version of the radio that can be pro-

grammed with up to sixteen (16) inde-

pendent trunked groups and/or

conventional radio channels. This unit fea-

tures an eight-digit alphanumeric liquid

crystal display (LCD) and a 16-position

knob for group/channel selection. The dis-

play also has status flags that indicate

various operating modes and it is backlit

for nighttime and low-level ambient light

operation.

Scan and System model radios have

an LCD similar to the Select model radio.

These radios have front panel keypads

that provide additional operating features

not available on the Select model radio.

The Scan model radio has a 4-button key-

pad and the System model radio has a

16-button keypad. Additional features in-

clude expanded system and group/chan-

nel selection capability, trunked group and

conventional channel scan capability,

trunked mode individual call capability, and

telephone interconnect call capability. The

numeric keypad on the System model ra-

dio also allows storage of ten (10) opera-

tor-entered telephone numbers and ten

(10) operator-entered radio ID numbers.

These numbers can be recalled at will and

initiated. Manually dialed telephone inter-

connect with overdial capability and con-

ventional mode DTMF dialing is also

provided by the System model’s 16-button

keypad.

Figure 3 - Scan Model

Figure 4 - System Model

The rotatable 16-position CONTROL

KNOB located on the top of the radio pro-

vides system, group or channel selection

according to how the radio is programmed.

A stop plate may be installed under the

knob to limit the maximum number of po-

sitions to less than sixteen (16). It is nor-

mally factory installed for fifteen (15)

positions.

On the Select model radio, the CON-

TROL KNOB selects any one of trunked

systems and groups or conventional chan-

nels programmed into the radio.

On Scan and System model radios,

the CONTROL KNOB is used in combina-

tion with the keypad to select a specific

trunked system and group or a conven-

tional channel. The selection method is

determined by the radio’s programming.

See the section entitled "SYS-

TEM/GROUP/CHANNEL SELECTION" in

the "OPERATION" section of this manual

for details.

PTT BUTTON

Pressing the PTT BUTTON on the

side of the radio turns on the radio‘s trans-

mitter. The "TX" status flag in the display

will turn on when the radio is transmitting.

Releasing the PTT BUTTON will return

operation to receive mode.

When operating on a trunked system,

the radio may be programmed to automat-

ically transmit (without the operator press-

ing the PTT BUTTON) to maintain

communication with the site controller. The

"TX" status flag in the display will turn on

when the radio is transmitting.

MONITOR BUTTON

Trunked Mode

The exact operation of a particular ra-

dio will vary depending upon its mode of

operation, its programming, and the par-

ticular radio system. Consult a radio sys-

tem’s representative for particular features

that are programmed into the radio.

The radio operates in trunked mode

when a trunked system is selected and it

operates in conventional mode when a

conventional system is selected.

When operating on a trunked system

in special call mode, pressing the MONI-

TOR BUTTON after an individual call has

been received will return the radio to the

group call mode. In this condition, the radio

will not respond on an individual basis but

it will then transmit group calls upon sub-

sequent activations of the PTT BUTTON.

The radio will also automatically return to

the group call mode after the programmed

individual call-back time-out period ex-

pires.

This button is also used to toggle be-

tween group and regroup settings if the

Dynamic Regrouping mode (with deselect

capability) has been activated by the site

controller.

On the System model radio, pressing

the MONITOR BUTTON will clear all digits

entered from the numeric keypad and re-

turn the radio to the selected group display.

Conventional Mode

When the radio is operating in conven-

tional mode (on a conventional channel),

the MONITOR BUTTON is used to tempo-

rarily unsquelch the receiver so channel

traffic can be monitored. Momentarily

pressing it will unsquelch the receiver.

If the selected channel has Channel

Guard (CG) and/or Type 99 (T99) coded-

squelch tone decode feature programmed

for the selected channel, this button is can

also be used to enable and disable the

programmed feature. Repeated activa-

tions will toggle CG and/or T99 between

the enabled (on) and disabled (off) states.

To toggle the programmed feature, press

and hold the MONITOR BUTTON for at

least two (2) seconds until the appropriate

status flag in the display toggles.

The MONITOR BUTTON is also used

to reset the radio after a Type 99 (T99)

selective call has been successfully re-

ceived. If the radio is operating in a Type

99 mode, momentarily press the MONI-

TOR BUTTON to reset the radio after a

T99 call is successfully received.

EMERGENCY BUTTON

When the radio is operating in trunked

mode, pressing and holding the red

EMERGENCY BUTTON on top of the ra-

dio for approximately one (1) second will

initiate an emergency call on the pro-

grammed home group. If no home group

is programmed into the radio the emer-

gency call will be transmitted on the se-

lected group.

In conventional mode, initiating an

emergency call by pressing the EMER-

GENCY BUTTON will cause the radio to

transmit GE-STAR emergency signaling

on the programmed emergency channel.

If no emergency channel is programmed,

GE-STAR emergency signaling will be

transmitted on the selected channel.

STEP BUTTON

(Scan And System Models Only)

The STEP button located on the key-

pad can be programmed to select trunked

groups and conventional channels or it can

be programmed to select systems. See the

section entitled "SYSTEM/GROUP/

CHANNEL SELECTION" for details.

STEP is also used to scroll through the

programmed special call table when the

special call mode is enabled.

SCAN BUTTON

(Scan And System Models Only)

Pressing the SCAN button on the key-

pad will toggle scan operation on and off

When the radio is scanning, the "SCN"

status flag in the display will turn on and all

groups/channels on the scan list in the

current system will be scanned.

SPC BUTTON

(Scan And System Models Only)

Pressing SPC will switch operation

from the group select mode to the special

call mode. The last selected special call

will be displayed.

While in special call mode, the next

programmed special call can be selected

by pressing STEP. Pressing 2nd then

STEP will select the previous programmed

special call. The caller’s ID of the last

received individual call and the last re-

ceived group call on the selected group are

a selectable using this method. See "

Spe-

cial Calls" for details.

2nd BUTTON (Scan And System

ModeIs Only)

On an M-PA Scan model radio the two

(2) center buttons (SCAN and SPC) on the

keypad are dual-function buttons. The

second or shifted functions are accessed

by first pressing the blue 2nd button. The

SCAN button’s second function is scan

add/delete for scan list updating. The sec-

ond function for the SPC button is the

keypad lock feature.

On an M-PA System model radio, six

(6) of the buttons on the keypad are dual-

function buttons. Press and release the

blue 2nd function button to shift keypad

selection to the scan add/delete (SCAN

button), the keypad lock feature (SPC but-

ton), STO, RCL, CLR, or STS buttons.

ADD/DELETE BUTTON

(Scan And System Models Only)

When in trunked mode, pressing and

releasing 2nd and then pressing A/D

(shifted SCAN button) will toggle the se-

lected group on and off the scan list. When

Figure 6 - System Model Keypad

Figure 5 - Scan Model Keypad

the selected group is on the scan list, the

‘S" status flag will show in the display.

In conventional mode, pressing and

releasing 2nd and then pressing A/D

(shifted SCAN button) will scroll the se-

lected channel’s scan priority between

non-priority scan ("S" status flag), priority-

two scan ("2" status flag), priority-one scan

("1" status flag) and no scan (no status

flags).

Scan must be turned off("SCN" status

flag off) before groups or channels can be

added to or deleted from the scan list.

LOCK BUTTON

(Scan And System ModeIs Only)

The radio’s keypad can be locked to

prevent accidental activations. To lock the

keypad, simultaneously press the 2nd and

LOCK (shifted SPC); "LOCKED" will be

displayed when the keypad is locked. To

unlock the keypad, press the 2nd and

LOCK buttons again; ‘UNLOCKED" will be

displayed momentarily.

STO BUTTON

(Shifted Digit 1 - System Model Only)

STO (shifted digit 1) allows ten (10)

telephone numbers and ten (10) radio ID

numbers to be stored and later recalled

with the RCL button.

Store a telephone number by entering

the number (up to 29 digits) followed by an

asterisk (*). Next, enter the storage loca-

tion (1 - 10) and press and release 2nd and

then press STO. "STORED" will be dis-

played for two seconds.

Store individual radio ID numbers by

entering the ID number (1 - 16382) fol-

lowed by a pound sign (#). Next enter the

storage location (1 - 10) and press and

release 2nd and then press STO.

‘STORED’ will be displayed for two sec-

onds.

RCL BUTTON

(Shifted Digit 3 - System Model Only)

RCL allows the previously stored tele-

phone or radio ID numbers to be recalled.

To recall a number first enter an * or # (*

for telephone number, # for radio ID num-

ber) and then enter the storage location (1

- 10). Next press and release 2nd and then

press RCL and the recalled number will be

displayed.

CLR BUTTON

(Shifted # Button-System Model Only)

To clear the last digit entered, press

and release 2nd and then press CLR

(shifted # button). Holding CLR down will

repetitively clear previous digits. The radio

will return to the last operating state when

all entered digits are cleared.

STS BUTTON

(Shifted Digit - System Model Only)

The STS button will be used for future

status operations.

INDICATORS

The radio’s liquid crystal display (LCD)

located on the front panel has eight (B)

alphanumeric characters and various

status flags located above and below the

alphanumeric characters. This display

provides indications of the current operat-

ing system, group or channel and it dis-

plays various other messages such as

special call ID names or numbers, and

telephone interconnect numbers. If pro-

grammed on, LCD backlighting will turn on

for a short period anytime an active button

is pressed or the CONTROL KNOB is ro-

tated.

The status flags located along the top

and bottom of the display indicate operat-

ing modes and conditions as follows:

EMG EMerGency mode - On indicates

an emergency call has been initi-

ated by the user. Flashing indi-

cates an emergency call has

been received.

NC No Control channel- On indi-

cates the radio is not receiving

the trunked control chan-

nel. Flashing indicates the

trunked system is in a failsoft

condition (supervisory radios

only).

Figure 7 - Liquid Crystal Display

HIgh power transmit - On indi-

cates the selected system or

channel has been pro-

grammed for high power transmit

operation. Off indicates low

power transmit.

MSG MeSsaGe - Flashing indicates

an individual call has been re-

ceived (trunked mode).

T99 Type 99 tone decode - On indi-

cates Type 99 tone decoding is

enabled on the seIected conven-

tional channel. Flashing in-

dicates a T99 selective call has

been received and the radio

must be reset to receive another

T99 call.

CNV CoNVentional mode - On indi-

cates the radio is operating in the

conventional mode.

SPC SPecial Call mode - On indicates

the special call mode has been

enabled. (Scan and System

models only).

Transmitter enabled - On when

the radio is transmitting.

BSY BuSY - When in trunked mode,

on indicates the radio is receiving

a call; flashing indicates a call

has been queued. In con-

ventional mode, on indicates a

carrier is being received.

CG Channel Guard - On indicates

Channel Guard decode is en-

abled on the selected conven-

tional channel.

BAT BATtery low - On indicates the

battery pack’s charge is low.

S Scan list - On indicates the se-

lected group or channel is on the

scan list (Scan and System mod-

els only).

1 priority 1 - On indicates the se-

lected conventional channel is

designated as the priority-one

scan channel. (Scan and Sys-

tem models only).

priority 2 - On indicates the se-

lected conventional channel is

designated as the priority-two

scan channel. (Scan and Sys-

tem models only).

SCN SCaN mode - On indicates the

radio is scanning. (Scan and

System models only).

UNIVERSAL DEVICE CONNECTOR

The Universal Device Connector

(UDC) is Iocated on the side of the radio-

just above the PTT and MONITOR BUT-

TONS. This connector provides con-

nections for the external accessories such

as a headset, a speaker-mike, or an emer-

gency lanyard. When the radio is locked in

a vehicular charger/repeater the UDC pro-

vides the audio and control connections

between the radio and the vehicular

charger/repeater. The UDC is also used by

the maintenance personnel when the radio

is programmed.

ALERT TONES

The radio sounds three (3) basic alert tones

or "beeps" to indicate various operating

conditions. Alert tones may be pro-

grammed to remain off at all times.

500 Hz Tone - trunked failure tone

sounds when a

trunked failure has oc-

curred (call denied,

failed confirmation).

1000 Hz Tone - key pressed - sounds

when a button is

pressed and a status

change occurs.

- channel access tone

sounds when a

trunked channel has

been assigned and it is

clear to talk.

- low battery sounds

when the battery

pack’s charge is low.

2500 Hz Tone - call queued tone

sounds when a

trunked call is queued.

OPERATION

POWER-UP

After the battery pack and antenna

have been installed, turn the radio on by

sliding the ON/OFF SWITCH on the bat-

tery pack up. After the radio has completed

a power-up self-test, it will begin opera-

tion on the last operating state as dis-

played in the LCD. If programmed on, the

power-up alert tone (beep) will be heard.

If the radio was previously operating in

a trunking system and communication with

this system’s control channel cannot be

established, the "NC" status flag will turn

on. This may occur if, for example, the

radio is out of range of the previous trunk-

ing site. It may be necessary to move to

another location, select another trunking

system, or a conventional channel.

SYSTEM/GROUP/CHANNEL SELEC-

TION

The Select model radio can be pro-

grammed with up to sixteen (16) different

system/group or channel combinations. To

select a particular group or channel, rotate

the CONTROL KNOB to the desired sys-

tem/group or channel in accordance with

the radio ‘s programming.

The Scan and System model radios

are programmed with

one of two different

system/group/channel selection modes as

follows:

•

Systems are selected with the

STEP button; groups and channels

are selected with the CONTROL

KNOB.

•

Systems are selected with the

CONTROL KNOB; groups and

channels are selected with the

STEP button.

STEP Button Programmed For Sys-

tem Selection; CONTROL KNOB Pro-

grammed For Group And Channel

Selection

System Selection

Press and release STEP to select the

next trunked system programmed into the

radio as indicated in the display. To select

the previous system, press and release

2nd and then press STEP. Holding down

STEP will cause the radio to automatically

scroll through the system list One or more

of the systems may be programmed for

conventional mode operation. Upon

reaching an end of the system list, the

radio may be programmed to stop selec-

tion or wrap around (go from one end to

the other).

On the System model radio, systems

can also be selected by entering the sys-

tem number from the numeric keypad and

then pressing STEP. If a number out of the

programmed range is entered, "RANGE"

will be displayed.

Group/Channel Selection

After the desired system is selected

with the STEP button, rotate the CON-

TROL KNOB to the desired trunked group

or conventional channel as indicated in the

display A stop-plate may be placed under

the knob to limit the maximum positions to

less than sixteen (16).

CONTROL KNOB Programmed For

System Selection; STEP Button Pro-

grammed For Group And Channel Se-

lection

System Selection

Rotate the CONTROL KNOB to the

desired trunked system as indicated in the

display. One or more of the systems

maybe programmed for conventional

mode operation. A stop-plate may be

placed under the knob to limit the maxi-

mum positions to less than sixteen (16).

Group/Channel Selection

After the desired system is selected

with the CONTROL KNOB, press and re-

lease STEP to select the next trunked

group or conventional channel pro-

grammed into the radio as indicated in the

display To select the previous group or

channel, press and release 2nd and then

press STEP. Holding down STEP will

cause the radio to automatically scroll

through the group/channel list. Upon

reaching an end of the group/channel list,

the radio may be programmed to stop se-

lection or wrap around (go from one end to

the other).

On the System model radio, groups or

channels can also be selected by entering

the group/channel number from the nu-

meric keypad and then pressing STEP. If

a number out of the programmed range is

entered, ‘RANGE’ will be displayed.

TRUNKED MODE OPERATION

Digital trunking provides fast commu-

nication access. In this mode the operator

selects a communication system and

group and the communication channel is

allocated through digital signalling with the

site.

Receiving A Message

1. Slide the ON/OFF SWITCH on

the battery pack up to the on

position. The radio will initiate

and complete the power-up self-

test then the system’s name and

"NC" status flag will be displayed

until a control channel is located.

When the control channel is lo-

cated, the "NC" status flag dis-

appears and the group name is

displayed.

2. Adjust the VOLUME CONTROL

to an approximate mid-range po-

sition.

3. Select the desired system and

group. See the section entitled

"SYSTEM/GROUP/CHANNEL

SELECTION" operating proce-

dures for details. The dis-

play indicates the selected

group.

4. The radio is now ready to receive

messages.

5. GROUP CALL - When a group

call is received, the radio un-

squelches on the assigned

channel and the "BSY" status

flag turns on. The group name or

the originator’s ID (depending on

programming) is displayed. Ad-

just the volume as necessary.

INDIVIDUAL CALL - If an indi-

vidual call (a call directed to only

one radio) is received, the radio

will unsquelch on the assigned

channel and the "BSY" status

flag will turn on. "*INDV*", the

originators ID number, or the

caller’s name (if programmed) is

displayed and the "MSG" status

flag flashes. Adjust the volume

as necessary.

Responding to an individual call

prior to the programmed call-

back time-out period will auto-

matically direct the transmission

to the originating unit on an indi-

vidual basis.

The "MSG" status flag will re-

main flashing even after the indi-

vidual call time-out period

expires. On a Scan or System

model radio, press the SPC but-

ton (SPecial Call) to call the

originating unit back after the

time-out period has expired. The

originator’s ID or name will be

displayed. Follow the proce-

dures for sending a special call.

Sending A Message

1. Turn the radio on, set the receive

audio level and select the de-

sired system and group.

2. Observe the display for the ab-

sence of the "BSY" status flag to

ensure no one is transmitting on

the selected group.

3. Press and hold the PTT BUT-

TON. The radio will perform the

necessary signalling re-

quired to obtain a communica-

tion channel.

4. When the channel has been ac-

quired, the "TX" and "BSY"

status flags are displayed

and the channel access alert

tone (one beep) sounds.

5. Hold the radio approximately

three inches from the mouth and

speak into the microphone in a

normal voice.

6. Release the PTT BUTTON

when the transmission is com-

plete. If the transmission ex-

ceeds the programmed Carrier

Control Timer limit, the radio will

unkey and an alert tone will

sound.

7. Listen for a reply.

Emergency Operation (Trunked Mode)

Receiving An Emergency Call

If the radio receives an Emergency Chan-

nel Assignment in trunked mode, an alert

tone sounds and the "EMG" status flag

starts flashing. Follow standard emergency

procedures.

Sending An Emergency Call

1. To enable an emergency trans-

mission, press and hold the

EMERGENCY BUTTON

(small red button near antenna)

for approximately one second.

The radio transmits an

emergency message until an

Emergency Channel Assign-

ment is received. Upon re-

ceipt, the "EMG" status flag

turns on and the radio begins

operating on the selected

group or the home group, de-

pending upon programming.

2. Press the PTT BUTTON and

speak into the microphone in a

normal voice.

3. Release the PTT BUTTON

when the transmission is com-

plete and listen for a reply.

4. When the radio receives a nor-

mal group channel assignment,

it will return to the previously se-

lected group.

Clearing An Emergency

An emergency can be cleared from a

System model radio if it is programmed

with supervisory privileges. To clear an

emergency from a supervisory System

model radio, press 2nd, CLR, and then the

EMERGENCY BUTTON all within one

second. The "EMG" status flag will turn off

when the emergency state has been

cleared by the trunked system.

Dynamic Regrouping

Dynamic Regrouping is a feature

which allows the System Manager to dy-

namically program new groups into se-

lected radios. Upon development of the

regrouping plan, the site controller sends

each radio the regroup plan number, knob

setting(s), and activate/deactivate com-

mands.

When the radio is regrouped, it will

alert the user and the display will indicate

"REGRP nn" (nn = 01 - 08 depending upon

the CONTROL KNOB setting).

If the regroup plan has deselect capa-

bility active on the selected system, press

the MONITOR BUTTON to toggle between

the group and regroup modes.

Wide Area System Scanning

The EDACS M-PA radio can be pro-

grammed for wide area system scan op-

eration for multi-site applications. Upon

the loss of the currently selected system’s

control channel, the radio can be pro-

grammed to automatically scan the control

channels of up to six other systems. If a

new control channel is found, the radio will

switch to the new system and sound an

alert tone. Group selection may change

upon switching to the new system.

The radio can also be programmed for

priority wide area system scan operation.

A priority system is assigned to each sys-

tem programmed into the radio. A radio

programmed in this manner will scan the

priority trunked system’s control channel

once every one, two, three or four minutes

(programmable). This priority scan timer is

reset each time the PTT BUTTON is

pressed.

Scanning Trunked Groups (Scan And

System Models Only)

Groups which have been previously

added to the scan list on a per system

basis can be scanned. Each system’s

scan list is retained in memory when the

radio is turned off or when the battery pack

is removed.

La pagina sta caricando ...

Ericsson M-PA EDACS Manuale utente

Marca: Ericsson

Modello: M-PA EDACS

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: Ericsson M-PA EDACS User manual

Ericsson M-PA EDACS Manuale utente

Ericsson M-PA EDACS Manuale utente

in altre lingue

Altri documenti