Whirlpool AKP 256/NA Program Chart

Categoria
Forni
Tipo
Program Chart
User and maintenance manual
Manuale d’uso e manutenzione
IT
AKP 256
GB1
YOUR SAFETY AND THAT OF OTHERS IS PARAMOUNT
This manual and the appliance itself provide important safety warnings, to be read and observed at all times.
All safety warnings give specific details of the potential risk present and indicate how to reduce risk of injury, damage and electric
shock resulting from improper use of the appliance. Carefully observe the following instructions:
- The appliance must be disconnected from the power supply before carrying out any installation work.
- Installation and maintenance must be carried out by a qualified technician, in compliance with the manufacturers
instructions and local safety regulations. Do not repair or replace any part of the appliance unless specifically stated in the
user manual.
- Regulations require that the appliance is earthed.
- The power cable must be long enough for connecting the appliance, once fitted in its housing, to the power supply
socket.
- For installation to comply with current safety regulations, an all-pole disconnect switch with minimum contact gap of
3 mm must be utilized.
- Do not use multiple plug adapters or extension leads.
- Do not pull the power supply cable in order to unplug the appliance.
- The electrical components must not be accessible to the user after installation.
- Do not touch the appliance with any wet part of the body and do not operate it when barefoot.
- This appliance is designed solely for use as a domestic appliance for cooking food. No other type of use is permitted
(e.g.: heating rooms). The Manufacturer declines all responsibility for inappropriate use or incorrect setting of the controls.
- The appliance is not intended for use by persons (including children) with any physical, sensory or mental impairment, or
without experience and knowledge of the appliance, unless supervised or previously instructed in its use by those
responsible for their safety.
- The accessible parts of the appliance may become very hot during use. Young children should be kept away from the
appliance and supervised to ensure that they do not play with it.
- During and after use, do not touch the heating elements or interior surfaces of the appliance - risk of burns. Do not allow
the appliance to come into contact with cloths or other flammable materials until all the components have cooled
sufficiently.
- At the end of cooking, exercise caution when opening the appliance door, letting the hot air or steam exit gradually
before accessing the oven. When the appliance door is shut, hot air is vented from the aperture above the control panel.
Do not obstruct the vent apertures.
- Use oven gloves to remove pans and accessories, taking care not to touch the heating elements.
- Do not place flammable materials in or near the appliance: a fire may break out if the appliance is inadvertently switched
on.
- Do not heat or cook sealed jars or containers in the appliance. The pressure that builds up inside might cause the jar to
explode, damaging the appliance.
- Do not use containers made of synthetic materials.
- Overheated oils and fats catch fire easily. Always remain vigilant when cooking foods rich in fat and oil.
- Never leave the appliance unattended during food drying.
- If alcoholic beverages are used when cooking foods (e.g. rum, cognac, wine), remember that alcohol evaporates at high
temperatures. As a result, there is a risk that vapours released by the alcohol may catch fire upon coming into contact with
the electrical heating element.
Scrapping of household appliances
- This appliance is manufactured with recyclable or reusable materials. Dispose of it in accordance with local waste disposal
regulations. Before scrapping, cut off the power supply cable.
- For further information on the treatment, recovery and recycling of household electrical appliances, contact your
competent local authority, the collection service for household waste or the store where you purchased the appliance.
IMPORTANT SAFETY INSTRUCTIONS
This is the danger symbol, pertaining to safety, which alerts users to potential risks to themselves and others.
All safety warnings are preceded by the danger symbol and the following terms:
DANGER
Indicates a hazardous situation which, if not avoided, will cause serious injury.
WARNING
Indicates a hazardous situation which, if not avoided, could cause serious injury.
GB2
After unpacking the oven, make sure that it has not been damaged during transport and that the oven door closes properly. In
the event of problems, contact the dealer or your nearest After-sales Service. To prevent any damage, only remove the oven
from its polystyrene foam base at the time of installation.
PREPARING THE HOUSING UNIT
Kitchen units in contact with the oven must be heat resistant (min 90°C).
Carry out all cabinet cutting work before fitting the oven in the housing and carefully remove all wood chips and sawdust.
After installation, the bottom of the oven must no longer be accessible.
For correct appliance operation, do not obstruct the minimum gap between the worktop and the upper edge of the oven.
ELECTRICAL CONNECTION
Make sure the power voltage specified on the appliance dataplate is the same as the mains voltage. The dataplate is on the front
edge of the oven (visible when the door is open).
Power cable replacement (type H05 RR-F 3 x 1.5 mm
2
) must be carried out by a qualified electrician. Contact an
authorized service centre.
GENERAL RECOMMENDATIONS
Before use:
- Remove cardboard protection pieces, protective film and adhesive labels from accessories.
- Remove the accessories from the oven and heat it at 200° for about an hour to eliminate the smell and fumes from the
insulating materials and protective grease.
During use:
- Do not place heavy objects on the door as they could damage it.
- Do not cling to the door or hang anything from the handle.
- Do not cover the inside of the oven with aluminium foil.
- Never pour water into the inside of a hot oven; this could damage the enamel coating.
- Never drag pots or pans across the bottom of the oven as this could damage the enamel coating.
- Make sure that the electrical cables of other appliances do not touch hot parts of the oven or become trapped in the door.
- Do not expose the oven to atmospheric agents.
Disposal of packing material
The packing material is 100% recyclable and is marked with the recycle symbol ( ). The various parts of the packing must
therefore be disposed of responsibly and in full compliance with local authority regulations governing waste disposal.
Scrapping the product
- This appliance is marked in compliance with European Directive 2002/96/EC, Waste Electrical and Electronic Equipment
(WEEE).
- By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
- The symbol on the product or on the accompanying documentation indicates that it should not be treated as
domestic waste but must be taken to an appropriate collection centre for the recycling of electrical and electronic
equipment.
Energy saving
- Only pre-heat the oven if specified in the cooking table or your recipe.
- Use dark lacquered or enamelled baking moulds as they absorb heat far better.
- Switch the oven off 10/15 minutes before the set cooking time. Food requiring prolonged cooking will continue to cook even
once the oven is switched off.
- This oven, which is intended to come into contact with foodstuffs, complies with European Regulation ( ) n.1935/2004
and has been designed, manufactured and sold in conformity with the safety requirements of the “Low Voltage” directive
2006/95/CE (which replaces 73/23/CEE and subsequent amendments), the protection requirements of “EMC” 2004/108/
CE.
INSTALLATION
SAFEGUARDING THE ENVIRONMENT
DECLARATION OF CONFORMITY
GB3
The oven does not work:
Check for the presence of mains electrical power and if the oven is connected to the electrical supply.
Turn off the oven and restart it to see if the fault persists.
Before calling the After-Sales Service:
1. See if you can solve the problem yourself with the help of the suggestions given in the “Troubleshooting guide“.
2. Switch the appliance off and back on again it to see if the fault persists.
If after the above checks the fault still occurs, get in touch with the nearest After-sales Service.
Always specify:
a brief description of the fault;
the type and exact model of the oven;
the service number (number after the word Service on the rating plate), located on the right hand edge of the oven cavity
(visible when the oven door is open). The service number is also indicated on the guarantee booklet;
your full address;
your telephone number.
If any repairs are required, please contact an authorised After-sales Service (to guarantee that original spare parts will be used
and repairs carried out correctly).
Oven exterior
IMPORTANT: do not use corrosive or abrasive detergents. If any of these products accidentally comes into contact with
the appliance, clean immediately with a damp cloth.
Clean the surfaces with a damp cloth. If it is very dirty, add a few drops of washing up detergent to the water. Finish off
with a dry cloth.
Oven interior
IMPORTANT: do not use abrasive sponges or metallic scrapers or scourers. Over time, these can ruin enamelled surfaces
and the oven door glass.
After every use, allow the oven to cool then clean it preferably while it is still warm in order to remove built-up dirt and
stains caused by food residues (e.g. food with a high sugar content).
Use proprietary oven detergents and follow the manufacturer’s instructions to the letter.
Clean the door glass with a suitable liquid detergent. The oven door can be removed to facilitate cleaning (see
MAINTENANCE).
The top heating element of the grill (see MAINTENANCE) can be lowered (some models only) to clean the roof of the oven.
N.B.: during prolonged cooking of foods with a high water content (e.g. pizza, vegetables, etc.) condensation may form
on the inside of the door and around the seal. When the oven is cold, dry the inside of the door with a cloth or sponge.
Accessories:
Soak the accessories in water with washing up detergent immediately after use, handling them with oven gloves if still
hot.
Food residues can be easily removed using a brush or sponge.
Cleaning the rear wall and catalytic side panels of the oven (if present):
IMPORTANT: do not use corrosive or abrasive detergents, coarse brushes, pot scourers or oven sprays which could
damage the catalytic surface and ruin its self-cleaning properties.
Operate the oven empty with the fan-assisted function at 200°C for about one hour
Next, leave the appliance to cool down before removing any food residue with a sponge.
TROUBLESHOOTING GUIDE
AFTER-SALES SERVICE
CLEANING
WARNING
- Never use steam cleaning equipment.
- Only clean the oven when it is cool to the touch.
- Disconnect the appliance from the power supply.
GB4
REMOVING THE DOOR
To remove the door:
1. Open the door fully.
2. Lift the catches and push them forwards as far as they will go (Fig. 1).
3. Close the door as far as it will go (A), lift it up (B) and turn it (C) until it is released (D) (Fig. 2).
To refit the door:
1. Insert the hinges in their seats.
2. Open the door fully.
3. Lower the two catches.
4. Close the door.
MOVING THE TOP HEATING ELEMENT (SOME MODELS ONLY)
1. Remove the side accessory holder grilles (Fig. 3).
2. Pull the heating element out a little (Fig. 4) and lower it (Fig. 5).
3. To reposition the heating element, lift it up, pulling it slightly towards you, making sure it comes to rest on the lateral
supports.
MAINTENANCE
WARNING
- Use protective gloves.
- Ensure the oven is cold before carrying out the following operations.
- Disconnect the appliance from the power supply.
Fig. 1 Fig. 2
Fig. 3 Fig. 4 Fig. 5
GB5
REPLACING THE OVEN LAMP
To replace the rear lamp (if present):
1. Disconnect the oven from the power supply.
2. Unscrew the lamp cover (Fig. 6), replace the lamp (see note for lamp type) and screw the lamp cover back on.
3. Reconnect the oven to the power supply.
To replace the side lamp (if present):
1. Disconnect the oven from the power supply.
2. Remove the side accessory holder grilles, if present (Fig. 3).
3. Use a screwdriver to prise off the lamp cover (Fig. 7).
4. Replace the lamp (see note for lamp type) (Fig. 8).
5. Reposition the lamp cover, pushing it on firmly until it snaps into place (Fig. 9).
6. Refit the side accessory holder grilles.
7. Reconnect the oven to the power supply.
N.B.:
- Only use 25-40W/230V type E-14, T300°C incandescent lamps, or 20-40W/230 V type G9, T300°C halogen lamps.
- Lamps are available from our After-sales Service.
IMPORTANT:
- If using halogen lamps, do not handle with bare hands since fingerprints can damage them.
- Do not use the oven until the lamp cover has been repositioned.
Fig. 6 Fig. 7 Fig. 8 Fig. 9
GB6
FOR ELECTRICAL CONNECTION, SEE THE PARAGRAPH ON INSTALLATION
1. Control panel
2. Upper heating element/grill
3. Cooling fan (not visible)
4. Dataplate (not to be removed)
5. Light
6. Fan
7. Turnspit (if present)
8. Lower heating element (hidden)
9. Door
10. Position of shelves (the number of shelves is indicated on the front of the oven)
11. Rear wall
N.B.:
- During cooking, the cooling fan may switch on at intervals in order to minimise energy consumption.
- At the end of cooking, after the oven in switched off, the cooling fan may continue to run for a while.
ACCESSORIES SUPPLIED
A. WIRE SHELF (2): the wire shelf can be used to grill food or as a support for pans, cake tins and other ovenproof cooking
receptacles.
B. DRIP TRAY (1): the drip tray is designed to be positioned under the wire shelf in order to collect fat or as an oven tray for
cooking meat, fish, vegetables, focaccia, etc.
ACCESSORIES NOT SUPPLIED
Other accessories can be purchased separately from the After-sales Service.
INSERTING WIRE SHELVES AND OTHER ACCESSORIES IN THE OVEN
1. Insert the wire shelf horizontally, with the raised part “A” upwards (Fig. 1).
2. The other accessories, like the drip tray and baking tray, are inserted with the raised part on the flat section “B” facing
upwards (Fig. 2).
INSTRUCTIONS FOR OVEN USE
Fig. A Fig. B
Fig. 1 Fig. 2
GB7
CONTROL PANEL DESCRIPTION
1. Function selector knob
2. Minute minder knob
3. Thermostat knob
4. Thermostat led
HOW TO OPERATE THE OVEN
Turn the selector knob to the required function.
The oven light switches on.
Turn the thermostat knob clockwise to the required temperature.
The thermostat led lights up, switching off again when the oven reaches the selected temperature.
At the end of cooking, turn the knobs to “0”.
MINUTE MINDER
The minute minder allows a time of between 1 and 60 minutes to be set. To set the minute minder, first turn it clockwise all the
way round and then set it to the desired time. Once the set time has elapsed, a signal sound will be emitted.
1 2 3 4
GB8
FUNCTION DESCRIPTION TABLE
FUNCTIONS KNOB
OFF To stop cooking and switch off the oven.
LAMP To switch the oven interior light on/off.
CONVENTIONAL
To cook any kind of dish on one shelf only. Use the 2nd shelf. Preheat the oven to the required
temperature. The thermostat led turns off when the oven is ready and food can be placed in it.
CONVECTION BAKE
To cook meat and pies with liquid filling (savoury or sweet) on a single shelf, and pizzas on one
or two shelves. This function delivers an even, golden, crisp top and base. When cooking on two
levels, switch the position of the dishes halfway through cooking to cook food more evenly. Use
the 2nd shelf to cook on one shelf only. To cook on two shelves, use the 1st and 3rd shelves.
Preheat the oven to the required temperature and place the food in it when the set temperature
is reached.
GRILL
To grill steak, kebabs and sausages; to cook vegetables au gratin and toast bread. Place food on
the 4th shelf. When grilling meat, use the drip tray to collect the cooking juices. Position it on the
3rd shelf, adding approx. half a litre of water. Preheat the oven for 3 - 5 min. During cooking the
oven door must remain closed.
TURBO GRILL
To roast large joints of meat (legs, roast beef, chickens). Position the food on the middle shelves.
Use the drip tray to collect the cooking juices. Position it on the 1st/2nd shelf, adding approx.
half a litre of water. It is advisable to turn the meat over during cooking for more even browning.
The oven does not have to be preheated. During cooking the oven door must remain closed.
DEFROST
To speed up defrosting of food. Place food on the middle shelf. Leave food in its packaging in
order to prevent it from drying out on the outside.
TURBOFAN
For food with a crisp base and soft top. Ideal for cooking cakes with liquid filling and no
precooked base (e.g. tarts, plum cakes, ricotta cakes as well as pizzas with abundant topping) on
a single shelf. Place food on the 2nd shelf. Preheat the oven before cooking.
This function is also ideal for frozen convenience foods (e.g. pizzas, chips, strudel, lasagna).
Follow the instructions on the product packaging.
FORCED AIR
To cook a variety of food requiring the same cooking temperature on a maximum of two shelves
at the same time (e.g.: fish, vegetables, cakes). This function can be used to cook different foods
without odours being transferred from one food to another. Use the 2nd shelf to cook on one
shelf only. To cook on two shelves, use the 1st and 3rd shelves, preheating the oven first.
BOTTOM HEATING
ELEMENT + FAN
To finish cooking food with a very liquid consistency and to obtain crisp, golden bases. Also
useful for thickening sauces. Place food on the 2nd shelf. The oven does not have to be
preheated.
BOTTOM HEATING
For browning the base of dishes at the end of cooking. Place food on the 1st/ 2nd shelf. This
function can also be used for slow cooking, e.g. meat or vegetable stews; in this case, use the
2nd shelf. The oven does not have to be preheated.
GB9
COOKING TABLES
Recipe
Function Preheating Shelf
(from bottom)
Temperature
(°C)
Time
(min)
Accessories
Leavened cakes
Yes 2 150-175 35-90 Cake tin on wire shelf
Yes 1-3 150-170 30-90
Shelf 3: cake tin on wire shelf
Shelf 1: cake tin on wire shelf
Filled pies (cheesecake,
strudel, apple pie)
Yes 2 150-190 30-85
Drip tray/ baking tray or cake
tin on wire shelf
Yes 1-3 150-190 35-90
Shelf 3: cake tin on wire shelf
Shelf 1: cake tin on wire shelf
Biscuits/Tartlets
Yes 2 160-175 20-45 Drip tray / baking tray
Yes 1-3 150-175 20-45
Shelf 3: wire shelf
Shelf 1: drip tray / baking tray
Choux buns
Yes 2 175-200 30-40 Drip tray / baking tray
Yes 1-3 170-190 35-45
Shelf 3: oven tray on wire shelf
Shelf 1: drip tray / baking tray
Meringues
Yes 2 100 110-150 Drip tray / baking tray
Yes 1-3 100 130-150
Shelf 3: oven tray on wire shelf
Shelf 1: drip tray / baking tray
Bread / Pizza / Focaccia
Yes 2 225-250 12-50 Drip tray / baking tray
Yes 1-3 225-250 25-50
Shelf 3: oven tray on wire shelf
Shelf 1: drip tray / baking tray
Frozen pizza
Yes 2 250 10-15
Shelf 2: drip tray / baking tray
or wire shelf
Yes 1-3 250 10-20
Shelf 3: oven tray on wire shelf
Shelf 1: drip tray / baking tray
Savoury pies (vegetable
pie, quiche)
Yes 2 175-200 40-50 Cake tin on wire shelf
Yes 1-3 175-190 55-65
Shelf 3: cake tin on wire shelf
Shelf 1: cake tin on wire shelf
Vols-au-vent / Puff pastry
crackers
Yes 2 175-200 20-30 Drip tray / baking tray
Yes 1-3 175-200 25-45
Shelf 3: oven tray on wire shelf
Shelf 1: drip tray / baking tray
Lasagne / Baked pasta /
Cannelloni / Flans
Yes 2 200 45-55 Oven tray on wire shelf
Lamb / Veal / Beef / Pork
1Kg
Yes 2 200 80-110
Drip tray or oven tray on wire
shelf
Chicken / Rabbit / Duck 1 Kg Yes 2 200 50-100
Drip tray or oven tray on wire
shelf
GB10
Turkey / Goose 3 Kg Yes 1/2 200 80-130
Drip tray or oven tray on wire
shelf
Baked fish / en papillote
(fillet, whole)
Yes 2 175-200 40-60
Drip tray or oven tray on wire
shelf
Stuffed vegetables
(tomatoes, courgettes,
aubergines)
Yes 2 175-200 50-60 Oven tray on wire shelf
Toast Yes 4 200 3-5 Wire shelf
Fish fillets / steaks Yes 4 200 20-30
Shelf 3: wire tray (turn food
halfway through cooking)
Shelf 2: drip tray with water
Sausages / Kebabs / Spare
ribs / Hamburgers
Yes 4 200 30-40
Shelf 4: wire shelf (turn food
halfway through cooking)
Shelf 3: drip tray with water
Roast chicken 1-1.3 Kg - 2 200 55-70
Shelf 2: wire shelf (turn food
two thirds of the way through
cooking if necessary)
Shelf 1: drip tray with water
Roast Beef rare 1 Kg - 2 200 35-45
Oven tray on wire shelf (turn
food two thirds of the way
through cooking if necessary)
Leg of lamb / Shanks - 2 200 60-90
Drip tray or oven tray on wire
shelf (turn food two thirds of
the way through cooking if
necessary)
Roast potatoes - 2 200 45-55
Drip-tray / baking tray (if
necessary, turn food two thirds
of the way through cooking)
Vegetable gratin - 2 200 20-30 Oven tray on wire shelf
Lasagna & Meat Yes 1-3 200 50-100
Shelf 3: oven tray on wire shelf
Shelf 1: drip tray or oven tray
on wire shelf
Meat & Potatoes Yes 1-3 200 45-100
Shelf 3: oven tray on wire shelf
Shelf 1: drip tray or oven tray
on wire shelf
Fish & Vegetables Yes 1-3 175 30-50
Shelf 3: oven tray on wire shelf
Shelf 1: drip tray or oven tray
on wire shelf
Recipe
Function Preheating Shelf
(from bottom)
Temperature
(°C)
Time
(min)
Accessories
GB11
How to read the cooking table
The table indicates the best function to use for any given food, to be cooked on one or more shelves at the same time. Cooking
times start from the moment food is placed in the oven, excluding pre-heating (where required). Cooking temperatures and
times are purely for guidance and will depend on the amount of food and type of accessory used. Use the lowest recommended
values to begin with and, if the food is not cooked enough, then move on to higher values. Use the accessories supplied and
preferably dark coloured metal cake tins and oven trays. You can also use pans and accessories in pyrex or stoneware, but bear
in mind that cooking times will be slightly longer. To obtain best results, carefully follow the advice given in the cooking table
for the choice of accessories (supplied) to be placed on the various shelves.
Cooking different foods at the same time
Using the “CONVECTION BAKE” function, you can cook different foods which require the same cooking temperature at the same
time (for example: fish and vegetables), using different shelves. Remove the food which requires less cooking time and leave
food which requires longer cooking time in the oven.
Desserts
- Cook delicate desserts with the conventional function on one shelf only. Use dark coloured metal cake tins and always
position them on the wire shelf supplied. To cook on more than one shelf, select the forced air function and stagger the
position of the cake tins on the shelves, aiding optimum circulation of the hot air.
- To check whether a raising cake is cooked, insert a wooden toothpick into the centre of the cake. If the toothpick comes
out clean, the cake is ready.
- If using non-stick cake tins, do not butter the edges as the cake may not rise evenly around the edges.
- If the cake “sinks” during cooking, set a lower temperature the next time, perhaps reducing the amount of liquid in the
mixture and mixing more gently.
- For sweets with moist fillings (cheesecake or fruit pies) use the “CONVECTION BAKE” function. If the base of the cake is
soggy, lower the shelf and sprinkle the bottom of the cake with breadcrumbs or biscuit crumbs before adding the filling.
Meat
- Use any kind of oven tray or pyrex dish suited to the size of the piece of meat being cooked. For roast joints, it is best to
add some stock to the bottom of the pan, basting the meat during cooking for added flavour. When the roast is ready, let
it rest in the oven for another 10-15 minutes, or wrap it in aluminium foil.
- When you want to grill meat, choose cuts with an even thickness all over in order to achieve uniform cooking results. Very
thick pieces of meat require longer cooking times. To prevent the meat from burning on the outside, lower the position of
the wire shelf, keeping the food farther away from the grill. Turn the meat two thirds of the way through cooking.
To collect the cooking juices it is advisable to place a drip-tray with half a litre of water directly under the grill on which the meat
is placed. Top-up when necessary.
Turnspit (only in some models)
Use this accessory to evenly roast large pieces of meat and poultry. Place the meat on the spit rod, tying it with string if chicken,
and check that it is secure before inserting the rod in the seat located on the front wall of the oven and resting it on the respective
support. To prevent smoke and to collect cooking juices, it is advisable to place a drip-tray with half a litre of water on the first
level. The rod has a plastic handle which must be removed before starting to cook, and used at the end of cooking to avoid burns
when taking the food out of the oven.
Pizza
Lightly grease the trays to ensure the pizza has a crispy base. Scatter the mozzarella over the pizza two thirds of the way through
cooking.
RECOMMENDED USE AND TIPS
IT12
LA SICUREZZA VOSTRA E DEGLI ALTRI È MOLTO IMPORTANTE
Il presente manuale e l’apparecchio stesso sono corredati da importanti messaggi relativi alla sicurezza, da leggere ed osservare
sempre.
Tutti i messaggi relativi alla sicurezza specificano il potenziale pericolo a cui si riferiscono ed indicano come ridurre il rischio di
lesioni, danni e scosse elettriche conseguenti ad un non corretto uso dell’apparecchio. Attenersi scrupolosamente alle seguenti
istruzioni:
- L’apparecchio deve essere scollegato dalla rete elettrica prima di effettuare qualunque intervento d’installazione.
- Linstallazione o la manutenzione deve essere eseguita da un tecnico specializzato, in conformità alle istruzioni del
fabbricante e nel rispetto delle norme locali vigenti in materia di sicurezza. Non riparare o sostituire qualsiasi parte
dell’apparecchio se non specificamente richiesto nel manuale d’uso.
- La messa a terra dell’apparecchio è obbligatoria.
- Il cavo di alimentazione deve essere sufficientemente lungo da permettere il collegamento dell’apparecchio, incassato nel
mobile, alla presa di rete.
- Affinché l’installazione sia conforme alle norme di sicurezza vigenti, occorre un interruttore onnipolare avente una
distanza minima di 3 mm. tra i contatti.
- Non utilizzare prese multiple o prolunghe.
- Non tirare il cavo di alimentazione dell’apparecchio per staccarlo dalla presa di corrente.
- Una volta terminata l’installazione, i componenti elettrici non dovranno più essere accessibili dall’utilizzatore.
- Non toccare l’apparecchio con parti del corpo umide e non utilizzarlo a piedi nudi.
- L’apparecchio è destinato esclusivamente ad uso domestico per la cottura di alimenti. Non sono consentiti altri usi (es.
riscaldare ambienti). Il fabbricante declina ogni responsabilità per usi non appropriati o per errate impostazioni dei
comandi.
- L’utilizzo dell’apparecchio non è consentito alle persone (inclusi i bambini) con ridotte capacità fisiche, sensoriali o
mentali, o con mancanza di esperienza o conoscenza, a meno che non abbiano avuto istruzioni riguardanti l’uso
dell’apparecchio da parte di persone responsabili della loro sicurezza.
- Le parti accessibili possono diventare molto calde durante l’uso. I bambini devono essere mantenuti a distanza e
sorvegliati affinchè non giochino con l’apparecchio.
- Durante e dopo l’uso non toccare gli elementi riscaldanti o le superfici interne dell’apparecchio perché possono causare
ustioni. Evitare il contatto con panni o altro materiale infiammabile fino a che tutti i componenti dell’apparecchio non si
siano sufficientemente raffreddati.
- A fine cottura, aprire la porta dell’apparecchio con cautela, facendo uscire gradualmente l’aria calda o il vapore prima di
accedere al suo interno. Con la porta dell’apparecchio chiusa, la fuoriuscita dellaria calda avviene dall’apertura posta al di
sopra del pannello comandi. Non ostruire in nessun caso le aperture di ventilazione.
- Usare guanti da forno per rimuovere pentole e accessori facendo attenzione a non toccare gli elementi riscaldanti.
- Non riporre materiale infiammabile nell’apparecchio o nelle sue vicinanze. Se l’apparecchio dovesse essere messo in
funzione inavvertitamente, potrebbe incendiarsi.
- Non riscaldare o cuocere nell’apparecchio cibi in barattoli chiusi. La pressione che si sviluppa all’interno potrebbe far
scoppiare il barattolo, danneggiando l’apparecchio.
- Non usare recipienti in materiale sintetico.
- I grassi e gli oli surriscaldati prendono facilmente fuoco. Sorvegliare la cottura di alimenti ricchi di grasso e di olio.
- Non lasciare mai l’apparecchio incustodito durante l’essiccazione dei cibi.
- Se nel cuocere cibi si aggiungono bevande alcoliche (ad es. rum, cognac, vino), tenere presente che l’alcool evapora a
temperature elevate. Non è quindi escluso che i vapori generati possano infiammarsi giungendo a contatto con la
resistenza elettrica.
Smaltimento elettrodomestici
- Questo prodotto è stato fabbricato con materiale riciclabile o riutilizzabile. Rottamarlo seguendo le normative locali per lo
smaltimento dei rifiuti. Prima di disfarsene, renderlo inutilizzabile tagliando il cavo di alimentazione.
- Per ulteriori informazioni sul trattamento, recupero e riciclaggio degli elettrodomestici, contattare l’idoneo ufficio locale, il
servizio di raccolta dei rifiuti domestici o il negozio presso il quale il prodotto è stato acquistato.
ISTRUZIONI IMPORTANTI PER LA SICUREZZA
Questo è il simbolo di pericolo, relativo alla sicurezza, il quale avverte dei potenziali rischi per l’utilizzatore e per gli altri.
Tutti i messaggi relativi alla sicurezza saranno preceduti dal simbolo di pericolo e dai seguenti termini:
PERICOLO
Indica una situazione pericolosa che, se non evitata, provoca lesioni gravi.
AVVERTENZA
Indica una situazione pericolosa che, se non evitata, potrebbe provocare lesioni gravi.
IT13
Dopo aver disimballato il forno verificare che non si sia danneggiato durante il trasporto e che la porta si chiuda perfettamente.
In caso di problemi, contattare il rivenditore o il Servizio Assistenza Clienti. Per prevenire eventuali danni, si consiglia di
rimuovere il forno dalla base in polistirolo soltanto prima dell’installazione.
PREDISPOSIZIONE DEL MOBILE PER INCASSO
I mobili della cucina adiacenti al forno devono resistere al calore (min 90°C).
Eseguire tutti i lavori di taglio del mobile prima di inserire il forno e rimuovere accuratamente trucioli o residui di segatura.
La parte inferiore del forno non deve più essere accessibile dopo l’installazione.
Per un corretto funzionamento del prodotto non ostruire l’apertura minima tra piano di lavoro e il lato superiore del forno.
CONNESSIONE ALLA RETE ELETTRICA
Controllare che la tensione indicata sulla targhetta matricola del prodotto sia la stessa della rete elettrica. Essa si trova sul bordo
anteriore del forno (visibile quando la porta è aperta).
Eventuali sostituzioni del cavo di alimentazione (tipo H05 RR-F 3 x 1,5 mm
2
) devono essere effettuate unicamente da
personale qualificato. Rivolgersi ai centri di assistenza autorizzati.
RACCOMANDAZIONI GENERALI
Prima dell’utilizzo:
- Rimuovere protezioni di cartone, pellicole trasparenti ed etichette adesive dagli accessori.
- Togliere gli accessori dal forno e riscaldarlo a 200° per unora circa in modo da eliminare odori e fumi derivanti da
materiale isolante e grassi di protezione.
Durante l’utilizzo:
- Non appoggiare pesi sulla porta in quanto essi potrebbero danneggiarla.
- Non aggrapparsi alla porta o appendere oggetti alla maniglia.
- Non ricoprire l’interno del forno con fogli di alluminio.
- Non versare mai acqua all’interno del forno caldo; lo smalto potrebbe danneggiarsi.
- Non trascinare sul fondo del forno pentole o tegami per non rovinare lo smalto.
- Accertarsi che i cavi elettrici di altri apparecchi non vadano a toccare le parti calde del forno o ad incastrarsi nella porta.
- Non esporre il forno agli agenti atmosferici.
Smaltimento imballaggio
Il materiale di imballaggio è riciclabile al 100% ed è contrassegnato dal simbolo di riciclaggio ( ). Le diverse parti
dell’imballaggio non devono essere disperse nell’ambiente, ma smaltite in conformità alle norme stabilite dalle autorità locali.
Smaltimento prodotto
- Questo apparecchio è contrassegnato in conformità alla Direttiva Europea 2002/96/EC, Waste Electrical and Electronic
Equipment (WEEE).
- Assicurandosi che questo prodotto sia smaltito in modo corretto, l’utente contribuisce a prevenire le potenziali
conseguenze negative per l’ambiente e la salute.
- Il simbolo sul prodotto o sulla documentazione di accompagnamento indica che questo prodotto non deve essere
trattato come rifiuto domestico, ma deve essere consegnato presso l’idoneo punto di raccolta per il riciclaggio di
apparecchiature elettriche ed elettroniche.
Risparmio energetico
- Preriscaldare l’apparecchio solo se indicato nella tabella di cottura o nella vostra ricetta.
- Usare stampi da forno scuri, laccati o smaltati, perché assorbono molto meglio il calore.
- Spegnere il forno 10/15 minuti prima del tempo totale di cottura impostato. Nel caso di cibi che richiedono tempi lunghi,
questi continueranno comunque a cuocere.
- Questo apparecchio, destinato ad entrare a contatto con prodotti alimentari, è conforme al regolamento ( ) n.1935/
2004 ed è stato progettato, costruito ed immesso sul mercato in conformità ai requisiti di sicurezza della direttiva “Bassa
Tensione”2006/95/CE (che sostituisce la 73/23/CEE e successivi emendamenti), requisiti di protezione della direttiva
“EMC” 2004/108/CE.
INSTALLAZIONE
CONSIGLI PER LA SALVAGUARDIA DELLAMBIENTE
DICHIARAZIONE DI CONFORMITÀ
IT14
Il forno non funziona:
Verificare che ci sia tensione in rete e che il forno sia connesso elettricamente.
Spegnere e riaccendere il forno, per accertare che l’inconveniente sia stato ovviato.
Prima di contattare il Servizio Assistenza:
1. Verificare che non sia possibile risolvere da soli il problema sulla base dei punti descritti in “Guida ricerca guasti”.
2. Spegnere e riaccendere l’apparecchio per accertarsi che l’inconveniente sia stato ovviato.
Se dopo i suddetti controlli l’inconveniente permane, contattare il Servizio Assistenza più vicino.
Indicare sempre:
una breve descrizione del guasto;
il tipo e il modello esatto del forno;
il numero Assistenza (è il numero che si trova dopo la parola Service sulla targhetta matricola), posto sul bordo interno
destro della cavità del forno (visibile a porta aperta). Il numero Assistenza è anche riportato sul libretto di garanzia;
il vostro indirizzo completo;
il vostro numero telefonico.
Qualora si renda necessaria una riparazione, rivolgersi ad un Centro di Assistenza Tecnica autorizzato (a garanzia dell’utilizzo
di pezzi di ricambio originali e di una corretta riparazione).
Esterno del forno
IMPORTANTE: non usare detergenti corrosivi o abrasivi. Se, inavvertitamente, uno di questi prodotti dovesse venire a
contatto con l’apparecchio, pulirlo subito con un panno umido.
Pulire con panno umido le superfici. Se molto sporco, aggiungere all’acqua qualche goccia di detersivo per i piatti.
Asciugare con panno asciutto.
Interno del forno
IMPORTANTE: Non utilizzare spugne abrasive, pagliette o raschietti metallici. Il loro impiego, col tempo, potrebbe
rovinare le superfici smaltate e il vetro della porta.
Dopo ogni uso, lasciare raffreddare il forno e pulirlo preferibilmente quando è ancora tiepido per rimuovere incrostazioni
e macchie dovute a residui di cibo (es. alimenti ad alto contenuto di zucchero).
Usare detergenti specifici per la pulizia del forno ed attenersi alle indicazioni del Fabbricante.
Pulire il vetro della porta con detergenti liquidi specifici. Per facilitare la pulizia della porta è possibile rimuoverla (vedi
MANUTENZIONE).
La resistenza superiore del grill (vedi MANUTENZIONE) è abbassabile (solo in alcuni modelli) per pulire la parte superiore
dell’interno dell’apparecchio.
NOTA: durante le cotture prolungate di alimenti ricchi di acqua (es. pizza, verdure, ecc.) è possibile la formazione di
condensa all’interno della porta e sulla guarnizione. A forno freddo, asciugare con un panno o una spugna.
Accessori:
Mettere a bagno gli accessori con detersivo per piatti dopo l’uso, maneggiandoli con guanti da forno, se ancora caldi.
I residui di cibo possono essere rimossi con una idonea spazzola o con una spugna.
Pulizia della paratia posteriore e dei pannelli laterali catalitici (se in dotazione):
IMPORTANTE: non usare detergenti corrosivi o abrasivi, spazzole ruvide, spugne per pentole o spray per forno che
potrebbero danneggiare la superficie catalitica, facendole perdere le sue proprietà autopulenti.
Far funzionare il forno a vuoto ad una temperatura di 200°C per circa unora con la funzione ventilato.
Al termine, lasciare raffreddare l’apparecchio ed usare una spugna per rimuovere eventuali residui di cibo.
GUIDA RICERCA GUASTI
SERVIZIO ASSISTENZA
PULIZIA
AVVERTENZA
- Non usare assolutamente pulitrici a getto di vapore.
- Effettuare la pulizia ad apparecchio freddo.
- Scollegare l’apparecchio dalla rete elettrica.
IT15
RIMOZIONE DELLA PORTA
Per togliere la porta:
1. Aprire completamente la porta.
2. Sollevare le levette di arresto delle cerniere in avanti fino al fermo (Fig. 1).
3. Chiudere la porta fino al bloccaggio (A), sollevarla (B) e ruotarla (C) fino allo sganciamento della stessa (D) (Fig. 2).
Per riposizionare la porta:
1. Inserire le cerniere nelle apposite sedi.
2. Aprire completamente la porta.
3. Abbassare le due levette di arresto.
4. Chiudere la porta.
SPOSTAMENTO DELLA RESISTENZA SUPERIORE (SOLO PER ALCUNI MODELLI)
1. Rimuovere le griglie porta accessori laterali (Fig. 3).
2. Estrarre leggermente la resistenza (Fig. 4) e abbassarla (Fig. 5).
3. Per riposizionare la resistenza, sollevarla, tirandola leggermente verso di sè, assicurandosi che appoggi sulle apposite sedi
laterali.
MANUTENZIONE
AVVERTENZA
- Utilizzare guanti protettivi.
- Eseguire le operazioni indicate ad apparecchio freddo.
- Scollegare l’apparecchio dalla rete elettrica.
Fig. 1 Fig. 2
Fig. 3 Fig. 4 Fig. 5
IT16
SOSTITUZIONE DELLA LAMPADA
Per sostituire la lampada posteriore (se in dotazione):
1. Scollegare il forno dalla rete elettrica.
2. Svitare il copri-lampada (Fig. 6), sostituire la lampada (per il tipo vedere nota) e riavvitare il copri-lampada.
3. Ricollegare il forno alla rete elettrica.
Per sostituire la lampada laterale (se in dotazione):
1. Scollegare il forno dalla rete elettrica.
2. Rimuovere le griglie porta accessori laterali, se in dotazione (Fig. 3).
3. Fare leva verso l’esterno con un cacciavite a taglio fino a rimuovere il coprilampada (Fig. 7).
4. Sostituire la lampada (per il tipo vedere nota) (Fig. 8).
5. Riposizionare il coprilampada e spingerlo contro la parete per agganciarlo correttamente (Fig. 9).
6. Rimontare le griglie porta accessori laterali.
7. Ricollegare il forno alla rete elettrica.
NOTA:
- Usare solo lampade ad incandescenza da 25-40W/230V tipo E-14, T300°C, o lampade alogene da 20-40W/230 V tipo G9,
T300°C.
- Le lampade sono disponibili presso i Servizi Assistenza Clienti.
IMPORTANTE:
- In caso di impiego di lampade alogene, non maneggiarle a mani nude, per evitare che vengano danneggiate dalle
impronte digitali.
- Non far funzionare il forno senza prima aver riposizionato il coprilampada.
Fig. 6 Fig. 7 Fig. 8 Fig. 9
IT17
PER IL COLLEGAMENTO ELETTRICO CONSULTARE LA PARTE RELATIVA ALL’INSTALLAZIONE
1. Pannello comandi
2. Resistenza superiore/grill
3. Ventola raffreddamento (non visibile)
4. Targhetta matricola (da non rimuovere)
5. Lampada
6. Ventola
7. Girarrosto (se in dotazione)
8. Resistenza inferiore (non visibile)
9. Porta
10. Posizione dei ripiani (il numero di livello è indicato sul frontale del forno)
11. Paratia
NOTA:
- Durante la cottura, è possibile che la ventola di raffreddamento si attivi ad intermittenza per ridurre il consumo
energetico.
- A fine cottura, dopo lo spegnimento del forno, la ventola di raffreddamento può continuare a funzionare per un certo
intervallo di tempo.
ACCESSORI IN DOTAZIONE
A. GRIGLIA (2): da usare per la cottura di cibi o come supporto per pentole, tortiere o qualunque recipiente adatto alla
cottura in forno.
B. LECCARDA (1): da usare, posizionata sotto la griglia, per raccogliere grasso o come piastra per cuocere carni, pesci,
verdure, focacce, etc.
ACCESSORI NON IN DOTAZIONE
È possibile acquistare separatamente altri accessori presso il Servizio Assistenza Clienti.
INSERIMENTO DI GRIGLIE E ALTRI ACCESSORI ALL’INTERNO DEL FORNO
1. Inserire la griglia orizzontalmente, con la parte rialzata “A” orientata verso l’alto (Fig. 1).
2. Per gli altri accessori, come leccarda e piastra dolci, l’inserimento avviene con la sporgenza presente sulla parte piana “B”
orientata verso l’alto (Fig. 2).
ISTRUZIONI PER L’USO DEL FORNO
Fig. A Fig. B
Fig. 1 Fig. 2
IT18
DESCRIZIONE PANNELLO COMANDI
1. Manopola selezione funzioni
2. Manopola contaminuti
3. Manopola termostato
4. Spia termostato
COME FAR FUNZIONARE IL FORNO
Ruotare la manopola selezione funzioni sulla funzione desiderata.
La lampada del forno si accende.
Ruotare la manopola del termostato in senso orario sulla temperatura desiderata.
La spia del termostato si accende e si spegne al raggiungimento della temperatura selezionata.
A fine cottura ruotare le manopole sulla posizione “0”.
CONTAMINUTI
Il contaminuti permette l’impostazione di un tempo da 1 a 60 minuti. Per impostare il contaminuti consigliamo di ruotare di un
giro completo la manopola in senso orario e di riportarlo sul tempo di desiderato. Allo scadere del tempo impostato verrà
emesso un segnale acustico.
1 2 3 4
1 / 1

Whirlpool AKP 256/NA Program Chart

Categoria
Forni
Tipo
Program Chart

in altre lingue