SCOTT 2023 SOLACE eRIDE Manuale utente

DISPLAY MANUAL

Display V01 & Remote V01

User Manual

EN

EN – 2

1 Safety

This instruction contains information that you must observe for

your personal safety and to prevent personal injury and damage

to property. They are highlighted by warning triangles and shown

below according to the degree of danger.

►Read the instructions completely before start-up and use. This will help

you to avoid hazards and errors.

►Keep the manual for future reference. This user manual is an integral part

of the product and must be handed over to third parties in case of resale.

NOTE

Also observe the additional documentation for the other components of the

HPR50 drive system as well as the documentation enclosed with the e-bike.

1.1 Hazard classiﬁcation

HAZARD

The signal word indicates a hazard with a high degree of risk which will

result in death or serious injury if not avoided.

WARNING

The signal word indicates a hazard with a medium level of risk which will

result in death or serious injury if not avoided.

CAUTION

The signal word indicates a hazard with a low level of risk which could result

in a minor or moderate injury if not avoided.

NOTE

A note in the sense of this instruction is important information about the

product or the respective part of the instruction to which special attention

is to be drawn.

EN – 3

1.2 Intended Use

The Display V01 and the Remote V01 of the drive system are intended exclu-

sively for Displaying information and operating your e-bike and must not be

used for other purposes.

Any other use or use that goes beyond this is considered improper and will

result in the loss of the warranty. In case of non-intended use, TQ-Systems

GmbH assumes no liability for any damage that may occur and no warranty

for proper and functional operation of the product.

Intended use also includes observing these instructions and all information

contained therein as well as the information on intended use in the supple-

mentary

documents enclosed with the e-bike.

Faultless and safe operation of the product requires proper transport, storage,

installation and operation.

1.3 Safety instructions for working on the e-bike

Make sure that the HPR50 drive system is no longer supplied with power

before doing any work (e.g. cleaing, chain maintenance, etc.) on the e-bike:

►Switch off the drive system at the Display and wait until the Display has

disappeared.

Otherwise, there is a risk that the drive unit may start in an uncontrolled way

and cause serious injuries, e.g. crushing, pinching or shearing of the hands.

All work such as repair, assembly, service and maintenance be carried out

exclusively by a bicycle dealer authorized by TQ.

1.4 Safety instructions for the Display und Remote

—Do not be distracted by the information shown on the Display while riding,

concentrate exclusively on the trafﬁc. Otherwise there is a risk of an acci-

dent.

—Stop your e-bike when you want to perform actions other than changing

the assistance level.

—The walk assist that can be activated via the Remote must only be used to

push the e-bike. Make sure that both wheels of the e-bike are in contact

with the ground. Otherwise there is a risk of injury.

—When the walk assist is activated, make sure that your legs are at a safe

distance from the pedals. Otherwise there is a risk of injury from the

rotating pedals.

EN – 4

1.5 Riding safety instructions

Observe the following points to avoid injuries due to a fall when starting with

high torque:

—We recommend that you wear a suitable helmet and protective clothing

every time you ride. Please observe the regulations of your country.

—The assistance provided by the drive system depends ﬁrstly on the

selected assistance mode and secondly on the force exerted by the rider

on the pedals. The higher the force applied to the pedals, the greater

the Drive Unit assistance. The drive support stops as soon as you stop

pedaling.

—Adjust the riding speed, the assistance level and the selected gear to the

respective riding situation.

CAUTION

Risk of injury

Practice the handling of the e-bike and its functions without assistance from

the drive unit at ﬁrst. Then gradually increase the assistance mode.

1.6 Safety instructions for using Bluetooth® and

ANT+

—Do not use Bluetooth® and ANT+ technology in areas where the use of

electronic devices with radio technologies is prohibited, such as hospitals

or medical facilities. Otherwise, medical devices such as pacemakers may

be disturbed by the radio waves and patients may be endangered.

—People with medical devices such as pacemakers or deﬁbrillators should

check with the respective manufacturers in advance that the function of

the medical devices is not affected by the Bluetooth® and ANT+ tech-

nology.

—Do not use Bluetooth® and ANT+ technology near devices with automatic

control, such as automatic doors or ﬁre alarms. Otherwise, the radio waves

may affect the devices and cause an accident due to possible malfunction

or accidental operation.

EN – 5

1.7 FCC

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference

that may cause undesired operation.

No changes shall be made to the equipment without the manufacturer’s

permission as this may void the user’s authority to operate the equipment.

This equipment complies with the RF exposure limits in FCC § 1.1310.

1.8 ISED

This device contains licence-exempt transmitter(s)/receiver(s) that comply

with Innovation, Science and Economic Development Canada’s licence-ex-

empt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may

cause undesired operation of the device.

This equipment complies with the RF exposure evaluation requirements of

RSS-102.

Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils

radio exempts de licence. L’exploitation est autorisée aux deux conditions

suivantes:

(1) le dispositif ne doit pas produire de brouillage préjudiciable, et

(2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage

susceptible de provoquer un fonctionnement indésirable.

Cet équipement est conforme aux exigences d’évaluation de l’exposition aux

RF de RSS-102.

EN – 6

2 Technical data

2.1 Display

Screen diagonal 2 inch

State of charge indication Seperate for Battery and range extender

Connectivity Bluetooth, ANT+ (Radio network standard

with low power consumption)

Protection class IP66

Dimension 74 mm x 32 mm x 12,5 mm /

2,91“ x 1,26“ x 0,49“

Weight 35 g / 1,23 oz

Operating temperature

Storage temperature

-5 °C to +40 °C / 23 °F to 104 °F

0 °C to +40 °C / 32 °F to 140 °F

Tab. 1: Technical data – Display V01

2.2 Remote

Protection class IP66

Weight with cable 25 g / 0,88 oz

Operating temperature

Storage temperature

-5 °C to +40 °C / 23 °F to 104 °F

0 °C to +40 °C / 32 °F to 104 °F

Tab. 2: Technical data – Remote

EN – 7

3 Operation and indication components

3.1 Overview Display

Pos. in

Fig. 1

Description

1 State of charge Battery

(max. 10 bars, 1 bar

corresponds 10 %)

2 State of charge range

extender (max. 5 bars,

1 bar corresponds 20 %)

3 Display panel for

different screen views

with riding informa-

tion (see section 6 auf

Seite 9)

4 Assist mode

(OFF, )

5 Button

3.2 Overview Remote

Pos. in

Fig. 2

Description

1 UP Button

2 DOWN Button

Fig. 1: Operation and indicaton

components on Display

1

2

4

5

3

Fig. 2: Operation on the Remote

1

2

EN – 8

4 Operation

►Make sure that the Battery is sufﬁciently charged before operation.

Switch on drive system:

►Switch on the drive unit by shortly

pressing the button (see Fig. 3) on

the Display.

Switch off drive system:

►Switch off the drive unit by long

pressing the button (see Fig. 3) on

the Display.

Fig. 3: Button on Display

EN – 9

5 Setup-Mode

5.1 Setup-Mode activate

►Switch off the drive system.

►Press and hold the button on the

Display (pos. 5 in Fig. 1) and the

DOWN button on the Remote

(pos. 2 in Fig. 2) for at least 5

seconds.

►Dealer Service Tool necessary if no

Rmote installed.

5.2 Settings

The following settings can be made in the setup-mode:

Setting Default value Possible values

Measure metric (km) metric (km) or angloamerican (mi)

Acoustic

acknowledge

signal

ON (sounds with each

buttonpress)

ON, OFF

Walk assist ON ON, OFF

Tab. 3: Settings in Setup-Mode

►Use the buttons on the Remote to scroll through the respective menu.

►Conﬁrm the selection made with the button on the Display. The next

selection is then Displayed or the setup mode is terminated.

►The Display screen can be changed by pressing the Remote button (> 3s)

if the walk assist function is deactivated due to country-speciﬁc laws and

regulations.

Fig. 4: Setup-Mode activate

>5 s

+

EN – 10

6 Riding information

At the bottom of the display, driving information can be shown in 4 different

views. Regardless of the currently selected view, the charging status of

the battery and optional range extender is displayed in the center and the

selected assistance level is shown at the top.

►With a double click press on the button on the Display (pos. 5 in Fig. 1)

you switch to the next screen view.

Screen view Riding information

—Battery state of charge in percent (68 %

in this example).

—Riding range in kilometers or miles (37

km in this example), the range calcu-

lation is an estimate that depends on

many parameters (see section 11.3 auf

Seite 17).

EN – 11

Screen view Riding information

—Current rider power in watt (163 W in this

example).

—Current drive unit power in watts (203 W

in this example).

—Current speed (24 km/h in this example)

in kilometers per hour (KPH) or miles per

hour (MPH).

—Current rider cadence in revolutions per

minute (61 RPM in this example).

EN – 12

Screen view Riding information

—Activated light (LIGHT ON)

—Switch on the light by pressing the UP

button and DOWN button at the same

time.

Depending on wheter the e-bike is equipped

with light and TQ smartbox (please see the

smartbox manual for more information).

—Deactivated light (LIGHT OFF)

—Switch off the light by pressing the UP

button and DOWN button at the same

time.

Tab. 4: Display – Riding information

EN – 13

7 Select assist mode

You can choose between 3 assist

modes or switch off the assist from

the drive unit. The selected assist

mode I, II or III is shown on the Display

with the corresponding number of

bars (see pos. 1 in Fig. 5).

—With a short press on the button

UP of the Remote (see Fig. 6) you

increase the assist mode.

—With a short press on the button

DOWN of the Remote (see Fig. 6)

you decrease the assist mode.

—With a long press (>3 s) on the

DOWN button of the Remote (see

Fig. 6), you switch off the assist

from the drive system. Fig. 5: Visualization of the selected

assist mode

1

Fig. 6: Select assist mode on the

Remote

EN – 14

8 Set connections

8.1 Connection e-bike to smartphone

NOTE

—You can download the TQ E-Bike app from the Appstore for IOS and the

Google Play Store for Android.

—Download the TQ E-Bike app.

—Select your bike (you only need to

pair your smartphone the ﬁrst time).

—Enter the numbers shown on the

Display in your phone and conﬁrm

the connection.

Fig. 7: Connection E-Bike to

Smartphone

765 100

EN – 15

8.2 Connection e-bike to bicycle computers

NOTE

—To make a connection with the bicycle computer, the e-bike and bicycle

computer must be within radio range (maximum distance approx.

10 meters).

—Pair your bicycle computer

(Bluetooth or ANT+).

—Select at least one of the three

shown sensors (see Fig. 8).

—Your e-bike is now connected.

Add sensors

Cadence

2948

eBike

2948

Power

2948

Cadence 82

Battery 43 %

Power 180 W

Your e-bike will

have a unique

identication

number.

Fig. 8: Connection e-bike to bicycle

computer

EN – 16

9 Walk assist

The walk assist makes it easier to push the e-bike, e.g. off-road.

NOTE

—The availability and characteristics of the walk assist are subject to coun-

try-speciﬁc laws and regulations. For example, the assistance provided

by the push assist is limited to a speed of max. 6 km/h in Europe.

—If you have locked the use of the walk assist in setup mode (see section

“„5.2 Settings“”), the next screen with riding information is Displayed

instead of activating the walk assist (see chapter “„6 Riding informa-

tion“”).

Activate walk assist

CAUTION

Risk of injury

►Make sure that both wheels of the e-bike are in contact with the ground.

►When the walk assist is activated, make sure that your legs are a sufﬁ-

cient safety distance from the pedals.

►When the e-bike is at standstill, press the UP button on the Remote for

longer than 0,5 s (see Fig. 9) to

activate the walk assist.

►Press the UP button again and

keep it pressed to move the e-bike

with the walk assist.

Deactivate walk assist

The walk assist is deactivated in the

following situations:

—Press the DOWN button on the Remote control (pos. 2 in Fig. 2).

—Press the button on the Display (pos. 5 in Fig. 1).

—After 30 s without actuation of the walk assist.

—By pedaling.

Fig. 9: Activate walk assist

>0,5 s

EN – 17

10 Reset to factory settings

►Switch on the drive system.

►Press and hold the button on the

Display and the DOWN button on

the Remote for at least 10 s, the

Setup-Mode is indicated ﬁrst and

RESET is followed (see Fig. 10).

►Make your choice with the buttons

on the Remote and conﬁrm it by

pressing the button on the Display.

►Dealer Service Tool necessary if no

Rmote installed.

When resetting to factory settings,

the following parameters are reset to

the factory settings:

—Drive Unit tuning

—Walk assist

—Bluetooth

—Acoustic acknowledge sounds

Fig. 10: Reset to factory settings

>10 s

+

>10 s

EN – 18

11 General riding notes

11.1 Functionality of the drive system

The drive system supports you when riding up to a speed limit permitted by

law which may vary depending on your country. The precondition for Drive

Unit assistance is that the rider pedals. At speeds above the permitted speed

limit, the drive system turns off the assistance until the speed is back within

the permitted range.

The assistance provided by the drive system depends ﬁrstly on the selected

assistance mode and secondly on the force exerted by the rider on the

pedals. The higher the force applied to the pedals the greater the Drive Unit

assistance.

You can also ride the e-bike without Drive Unit assistance, e.g. when the drive

system is switched off or the Battery is empty.

11.2 Gear shift

The same speciﬁcations and recommendations apply for shifting gears on an

e-bike as for shifting gears on a bicycle without Drive Unit assistance.

11.3 Riding range

The possible range with one Battery charge is inﬂuenced by various factors,

for example:

—Weight of e-bike, rider and baggage

—Selected assist mode

—Speed

—Route proﬁle

—Selected gear

—Age and state of charge of the Battery

—Tire pressure

—Wind

—Outside temperature

The range of the e-bike can be extended with the optional range extender.

EN – 19

12 Cleaning

—The components of the drive system must not be cleaned with a

high-pressure cleaner.

—Clean the Display and the Remote only with a soft, damp cloth.

13 Maintenance and Service

All service, repair or maintenance work performed by a TQ authorized

bicycle dealer. Your bicycle dealer can also help you with questions about

bicycle use, service, repair or maintenance.

14 Environmentally friendly disposal

The components of the drive system and the batteries must not be

disposed of in the residual waste garbage can.

—Dispose of metal and plastic components in accordance with-

country-speciﬁc regulations.

—Dispose of electrical components in accordance with country-speciﬁc

regulations. In EU countries, for example, observe the national imple-

mentations of the Waste Electrical and Electronic Equipment Directive

2012/19/EU (WEEE).

—Dispose of batteries and rechargeable batteries in accordance with the

country-speciﬁc regulations. In EU countries, for example, observe the

national implementations of the Waste Battery Directive 2006/66/EC in

conjunction with Directives 2008/68/EC and (EU) 2020/1833.

—Observe addtitonally the regulations and laws of your country for disposal.

In addition you can return components of the drive system that are no longer

required to a bicycle dealer authorized by TQ.

La pagina sta caricando ...

SCOTT 2023 SOLACE eRIDE Manuale utente

SCOTT 2023 SOLACE eRIDE Manuale utente

in altre lingue