Asus Q670EM-IM-A Manuale utente

Marca: Asus

Modello: Q670EM-IM-A

Categoria: Schede madri

Tipo: Manuale utente

Industrial Motherboard

Q670EM-IM-A

E21753

First Edition

March 2023

No part of this manual, including the products and software described in it, may be reproduced,

transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any

means, except documentation kept by the purchaser for backup purposes, without the express written

permission of ASUSTeK COMPUTER INC. (“ASUS”).

Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless

such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the

product is defaced or missing.

ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS

OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS

DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,

INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,

LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),

EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY

DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.

SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR

INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,

AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO

RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS

MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.

Products and corporate names appearing in this manual may or may not be registered trademarks or

copyrights of their respective companies, and are used only for identification or explanation and to the

owners’ benefit, without intent to infringe.

iii

Contents

Chapter 1 Product Overview

1.1 Package contents......................................................................... 1-1

1.2 Features ........................................................................................ 1-1

1.3 Specifications ............................................................................... 1-2

Chapter 2: Motherboard Information

2.1 Before you proceed ..................................................................... 2-1

2.2 Motherboard layout ...................................................................... 2-2

2.3 Central Processing Unit (CPU) ................................................... 2-4

2.3.1 CPU installation .............................................................. 2-5

2.3.2 CPU heatsink and fan assembly installation ................... 2-7

2.4 System memory ........................................................................... 2-9

2.5 Jumpers ...................................................................................... 2-10

2.6 Connectors ................................................................................. 2-14

2.6.1 Rear panel connectors .................................................. 2-14

2.6.2 Internal connectors ....................................................... 2-16

2.7 Slot .............................................................................................. 2-27

Chapter 3: BIOS Setup

3.1 BIOS Setup program .................................................................... 3-1

3.2 Main menu .................................................................................... 3-2

3.3 Advanced menu ........................................................................... 3-2

3.3.1 PCH-FW Configuration ................................................... 3-2

3.3.2 Trusted Computing ......................................................... 3-3

3.3.3 CPU Configuration .......................................................... 3-4

3.3.4 Graphics Configuration ................................................... 3-5

3.3.5 Power Management ....................................................... 3-5

3.3.6 PCI Express Configuration .............................................. 3-6

3.3.7 Super IO Configuration ................................................... 3-8

3.3.8 Serial Console Redirection ............................................. 3-9

3.3.9 SATA Configuration ...................................................... 3-12

3.3.10 VMD setup menu .......................................................... 3-13

3.3.11 Network Stack Configuration ........................................ 3-13

3.3.12 USB Configuration ........................................................ 3-13

3.3.13 NVMe Configuration ...................................................... 3-15

3.3.14 Onboard Devices Configuration .................................... 3-15

3.3.15 APM Configuration ........................................................ 3-16

3.3.16 EZ-Flash ....................................................................... 3-17

3.3.17 IO Expander Configuration ........................................... 3-17

3.3.18 Watchdog Timer ............................................................ 3-18

3.4 Hardware Monitor menu ............................................................ 3-18

3.5 Security menu ............................................................................ 3-19

3.5.1 Administrator Password ................................................ 3-19

3.5.2 User Password .............................................................. 3-20

3.5.3 Secure Boot .................................................................. 3-20

3.6 Boot menu .................................................................................. 3-21

3.7 Exit menu .................................................................................... 3-22

Appendix

Notices .......................................................................................................A-1

Service and Support .................................................................................A-5

1-1

Chapter 1: General information

1.1 Package contents

Check your industrial motherboard package for the following items.

1 x ASUS Q670EM-IM-A Motherboard

1 x Serial ATA 6.0 Gb/s cable

2 x M.2 screw packages

1 x ASUS I/O Shield

If any of the above items is damaged or missing, contact your distributor or

sales representative immediately.

1.2 Features

• Intel® socket 1700 for 12th Gen Intel® Core™ i9/ i7/ i5/ i3, Pentium®, and

Celeron® processors Max. 125W TDP

• Four Dual Channel DDR5 U-DIMMs up to 128GB

• 7 x SATA 6.0 Gb/s, 4 x USB 3.2 Gen 2, 5 x USB 3.2 Gen 1, 4 x USB 2.0,

10 x COM ports

• 2 x PCIe x16 slots, 2 x PCIe x4 slots, 1 x M.2 (Key E, 2230) for WiFi/BT device

supports Intel® CNVi, 1 x M.2 (Key M, 2242/2260/2280) with PCIe and SATA

modes supports NVMe

• Multi-display: 4 x DisplayPorts

Chapter 1

Product overview

Q670EM-IM-A

1-2

1.3 Specifications

(continued on the next page)

CPU

LGA1700 for Intel® 12th/13th Gen. Core™ i9/ i7/ i5/ i3/

Pentium®/Celeron® Processors

Supports up to 125W TDP

Chipset Intel® Q670E Chipset

Memory

4 x U-DIMM, Max. 128GB, DDR5

4400MT/s (2DPC - 1DIMM 1R&2R)

4000MT/s (2DPC – 2DIMM 1R)

3600MT/s (2DPC – 2DIMM 2R)

Display 4 x DisplayPort, supports DP++ 1.4, up to 3840 x 2160 @

60Hz

Expansion slots

1 x PCIe 5.0 x16 Slot (x16 mode / x8+x8 mode)

1 x PCIe 4.0 x4 Slot (x4 mode)

1 x PCIe 5.0 x16 Slot (x8 mode)

1 x PCIe 4.0 x4 Slot (x4 mode)

1 x M.2 E key, Type 2230 for WIFI/BT device (PCIe x1 &

USB2.0 & CNVI)

1 x M.2 M key, Type 2242/2260/2280 (PCIe x4 / SATA

mode) supports NVMe

Storage 7 x SATA Gen 3.0, Up to 6Gb/s

Support RAID 0,1,5,10

LAN

3 x Intel® Lan controllers:

1 x Intel® I210AT

1 x Intel® I226V

1 x Intel® I226LM (Intel vPro supported)

Audio Realtek ALC897 High Definition Audio CODEC

Rear panel I/O ports

4 x DisplayPort

2 x USB 3.2 Gen 1 ports

4 x USB 3.2 Gen 2 ports (3 x Type-A, 1 x Type-C®)

3 x RJ45 LAN ports

1 x Serial port (supports RS232/422/485)

3 x Audio jack (Line-Out, Line-In, Mic in)

1-3

Chapter 1: General information

Internal I/O ports

9 x COM Port headers (RS232)

1 x USB 3.2 Gen 1 header supports additional 2 USB 3.2

Gen 1 ports

1 x USB 3.2 Gen 1 vertical connector

2 x USB 2.0 headers support additional 4 x USB 2.0 ports

1 x CPU Fan header with PWM mode

3 x Chassis Fan headers with PWM mode

1 x Front Panel Audio header (AAFP)

1 x System Panel header

1 x Chassis Intrusion header

1 x Speaker header

1 x I2C header

1 x Clear CMOS header

1 x COM Debug header

1 x LPT port header

1 x Buzzer

1 x PS/2 header

1 x S/PDIF header

1 x SPI TPM header

1 x Disable ME jumper

1 x AT/ATX mode selection header

1 x 24-pin ATX Power connector

1 x 8-pin ATX Power connector

GPIO 1 x 8-bit GPIO header

Watch dog timer Yes

Power requirement AT mode / ATX mode

Operation Temperature 0~60°C

Non-Operation

Temperature -40~85°C

Relative Humidity 40°C @ 10%~95%

OS support

Windows® 10 (64-bit)

Windows® IoT Enterprise

Ubuntu

RedHat Enterprise

Fedora Workstation

OpenSUSE

Certification CE, FCC, BSMI, VCCI, RCM

Form Factor Micro ATX Form Factor, 244cm x 244cm

Specifications are subject to change without notice. Please refer to the ASUS

website for the latest specifications.

Q670EM-IM-A

1-4

2-1

Chapter 2: Motherboard information

Chapter 2

Motherboard information

2.1 Before you proceed

Take note of the following precautions before you install motherboard components

or change any motherboard settings.

• Unplug the power cord from the wall socket before touching any

component.

• Before handling components, use a grounded wrist strap or touch a safely

grounded object or a metal object, such as the power supply case, to avoid

damaging them due to static electricity.

• Hold components by the edges to avoid touching the ICs on them.

• Whenever you uninstall any component, place it on a grounded antistatic

pad or in the bag that came with the component.

• Before you install or remove any component, always remove the AC power

by unplugging the power cord from the power outlet. Failure to do so may

cause severe damage to the motherboard, peripherals, or components.

Q670EM-IM-A

2-2

2.2 Motherboard layout

Place this side

towards the rear

of the chassis

Place eight (8) screws into the holes indicated by circles to secure the

motherboard to the chassis.

Do not overtighten the screws! Doing so can damage the motherboard.

2-3

Chapter 2: Motherboard information

Connectors/Jumpers/Slots Page

1. CPU and Chassis Fan headers (4-pin CPU_FAN, 4-pin CHA_FAN1-3) 2-19

2. ATX Power connectors (24-pin ATX_PWR, 8-pin EATX12V) 2-25

3. M.2 socket 3 (M.2(SOCKET3)) 2-21

4. Intel® LGA1700 CPU socket 2-4

5. DDR5 U-DIMM slots 2-9

6. USB 3.2 Gen 1 connector (20-1 pin U32G1_910) 2-16

7. SATA 6.0Gb/s ports (7-pin SATA6G_1-7) 2-19

8. SPI TPM header (14-1 pin TPM) 2-18

9. System Panel header (10-1 pin F_PANEL) 2-20

10. Chassis Intrude header (4-1 pin CHASSIS) 2-12

11. Serial Port connectors (10-1 pin COM2-10) 2-22

12. Speaker header (4-pin SPEAKER) 2-21

13. M.2 Wi-Fi (M.2(WIFI)) 2-22

14. Clear CMOS header (2-pin CLRTC) 2-13

15. Disable ME Update jumper (3-pin DIS_ME) 2-11

16. AT/ATX mode selection (3-pin AT_ATX_SEL) 2-11

17. USB 2.0 connector (10-1 pin USB_1112, USB_713) 2-17

18. Keyboard and Mouse Port connector (8-pin KBMS_CON) 2-26

19. LPT header (26-1 pin LPT) 2-16

20. Front Panel Audio header (10-1 pin AAFP) 2-24

21. Digital Audio header (4-1 pin SPDIF_OUT) 2-23

22. I2C header (6-1 pin I2C) 2-23

23. General purpose input/output connector (10-pin GPIO_CON) 2-18

24. PCI Express x4 slots 2-27

25. PCI Express x16 slots 2-27

26. USB 3.2 Gen 1 vertical connector (U32G1_8) 2-17

27. COM1 Ring/+5V/+12V selection (6-pin COM1_SEL) 2-10

Q670EM-IM-A

2-4

Unplug all power cables before installing the CPU.

• Upon purchase of the motherboard, ensure that the PnP cap is on

the socket and the socket contacts are not bent. Contact your retailer

immediately if the PnP cap is missing, or if you see any damage to the

PnP cap/socket contacts/motherboard components. The manufacturer will

shoulder the cost of repair only if the damage is shipment/transit-related.

• Keep the cap after installing the motherboard. The manufacturer will

process Return Merchandise Authorization (RMA) requests only if the

motherboard comes with the cap on the socket.

• The product warranty does not cover damage to the socket contacts

resulting from incorrect CPU installation/removal, or misplacement/loss/

incorrect removal of the PnP cap.

2.3 Central Processing Unit (CPU)

The motherboard comes with a surface mount LGA1700 socket designed for

the 13th Gen Intel® Core™ and 12th Gen Intel® Core™ i9/ i7/ i5/ i3, Pentium®, and

Celeron® processors.

LGA1700

2-5

Chapter 2: Motherboard information

2.3.1 CPU installation

2 3

Q670EM-IM-A

2-6

2-7

Chapter 2: Motherboard information

2.3.2 CPU heatsink and fan assembly installation

To install the CPU heatsink and fan assembly

Apply Thermal Interface Material to

the CPU cooling system and CPU

before you install the cooling system,

if necessary.

Q670EM-IM-A

2-8

To uninstall the CPU heatsink and fan assembly

2-9

Chapter 2: Motherboard information

2.4 System memory

The motherboard comes with Dual Inline Memory Modules (DIMM) slots designed

for DDR5 (Double Data Rate 5) memory modules.

A DDR5 memory module is notched differently from a DDR, DDR2, DDR3, or

DDR4 module. DO NOT install a DDR, DDR2, DDR3, or DDR4 memory module

to the DDR5 slot.

Recommended memory configurations

DIMM_A21st DIMM_A21st

DIMM_B21st

DIMM_A1

DIMM_A21st

DIMM_B1

DIMM_B21st

DIMM_A1

DIMM_A2

DIMM_B1

DIMM_B2

1st

Q670EM-IM-A

2-10

2.5 Jumpers

1. COM1 Ring/+5V/+12V selection (6-pin COM1_SEL)

This jumper allows you to select 5V or 12V depending on your COM device.

Setting Pins

+12V 1-2

+5V 3-4

Ring (Default) 5-6

Connector type

HEADER 2x3p, 2.54mm pitch, S/T

(Default)

+5V+12V

COM1_SEL

2-11

Chapter 2: Motherboard information

2. AT/ATX mode selection (3-pin AT_ATX_SEL)

In ATX mode (default), you will need to manually press the power button to

turn on the system power. In AT mode, the board will automatically turn on

when system power is connected.

Connector type

HEADER 1x3p, 2.54mm pitch, S/T

Pins Description

1-2 (Default) ATX mode

2-3 AT mode

123

ATX mode

(Default)

AT mode

AT_ATX_SEL

3. Disable ME jumper (3-pin DIS_ME)

This jumper allows you to enable or disable the Intel® ME function. Set this

jumper to pins 1-2 to enable (default) the Intel® ME function and to pins 2-3 to

disable it.

Connector type

HEADER 1x3p, 2.54mm pitch, S/T

Q670EM-IM-A

2-12

4. Chassis intrusion header (4-1 pin CHASSIS)

This header is for a chassis-mounted intrusion detection sensor or switch.

Connect one end of the chassis intrusion sensor or switch cable to this

connector. The chassis intrusion sensor or switch sends a high-level signal to

this connector when a chassis component is removed or replaced. The signal

is then generated as a chassis intrusion event.

Connector type

HEADER 4p, K2, 2.54mm pitch

+5VSB_MB

Chassis Signal

GND

CHASSIS

PIN 1

La pagina sta caricando ...

Asus Q670EM-IM-A Manuale utente

Marca: Asus

Modello: Q670EM-IM-A

Categoria: Schede madri

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: Asus Q670EM-IM-A User manual