OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
Natural Sound Stereo Integrated Amplifier
Préampli/ampli de puissance stéréo de la série “Natural Sound”
Natural Sound Stereo-Verstärker
Natural Sound Integrerad Stereo Förstärkare
Amplificatore integrato stereo a Suono Naturale
Amplificador integrado estéreo de Sonido Natural
Natural Sound Geïntegreerde Stereo Versterker
AX-380
This product complies with the radio frequency interference requirements of the Council Directive 82/499/EEC and/or
87/308/EEC.
Cet appareil est conforme aux prescriptions de la directive communautaire 87/308/CEE.
Diese Geräte entsprechen der EG-Richtlinie 82/499/EWG und/oder 87/308/EWG.
Dette apparat overholder det gaeldende EF-direktiv vedrørende radiostøj.
Questo apparecchio è conforme al D.M.13 aprile 1989 (Direttiva CEE/87/308) sulla soppressione dei radiodisturbi.
Este producto está de acuerdo con los requisitos sobre interferencias de radio frequencia fijados por el Consejo Directivo
87/308 CEE.
Dit product voldoet aan de EEG normen betreffende radio-frekwentie storingen 82/499/EEG en/of 87/308/EEG.
2
●
Remote Control Transmitter
●
Emetteur de télécommande
●
Fernbedienungsgeber
●
Fjärrkontrollsändare
●
Trasmittente del telecomando
●
Transmisor del control remoto
●
Afstandbediening
●
Batteries (size AA, R6, UM-3)
●
Piles (taille AA, R6, UM-3)
●
Batterien (größ AA, R6, UM-3)
●
Batterier (storlek AA, R6, UM-3)
●
Batterie (taglia AA, R6, UM-3)
●
Pilas (tamaño AA, R6, UM-3)
●
Batterijen (maat AA, R6, UM-3)
SUPPLIED ACCESSORIES
●
After unpacking, check that the following parts are contained.
ACCESSOIRES FOURNIS
●
Après le déballage, vérifier que les pièces suivantes sont incluses.
MITGELIEFERTE ZUBEHÖRTEILE
●
Nach dem Auspacken überprüfen, ob die folgenden Teile vorhanden sind.
MEDFÖLJANDE TILLBEHÖR
●
Kontrollera effer det apparaten packats upp att följande delar finns med.
ACCESSORI IN DOTAZIONE
●
Disimballato l’apparecchio, controllate di possedere tutte le parti menzionate.
ACCESORIOS INCLUIDOS
●
Desembale el aparato y verifique que los siguientes accesorios están en la caja.
BIJGELEVERDE ACCESSOIRES
●
Controleer na het uitpakken of de volgende onderdelen voorhanden zijn.
POWER
PLAY/CUT
PHONO
SKIP PLAY CD
SEARCH PAUSE/STOP DISC SKIP
—
+
A/B/C/D/E
TUNER
DIR A
DECK A/B
DIR B TAPE 1
TAPE 2
REC/PAUSE
STOP
REC MUTE
AUX
VOLUME
—
+
PRESET
PLAY
1. To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2. Install this unit in a cool, dry, clean place – away from windows,
heat sources, sources of excessive vibration, dust, moisture and
cold. Avoid sources of humming (transformers, motors). To
prevent fire or electrical shock, do not expose the unit to rain or
water.
3. Never open the cabinet. If something drops into the set, contact
your dealer.
4. Do not use force on switches, controls or connection wires. When
moving the unit, first disconnect the power plug and the wires
connected to other equipment. Never pull the wires themselves.
5. The openings on the cabinet assure proper ventilation of the unit.
If these openings are obstructed, the temperature inside the
cabinet will rise rapidly and eventually damage the circuits.
Therefore, avoid placing objects against these openings and do
not install the unit where the flow of air through the ventilation
openings could be impeded.
6. Always set the VOLUME control to “–
∞
” before starting the audio
source play. Increase the volume gradually to an appropriate level
after playback has been started.
7. Do not attempt to clean the unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
8. Be sure to read the “TROUBLESHOOTING” section regarding
common operating errors before concluding that the unit is faulty.
9. When not planning to use this unit for long periods of time (ie.,
vacation, etc.), disconnect the AC power plug from the wall outlet.
10.To prevent lightning damage, disconnect the AC power plug and
disconnect the antenna cable when there is an electrical storm.
11.Grounding or polarization – Precautions should be taken so that
the grounding or polarization of an appliance is not defeated.
12. AC outlet
Do not connect audio equipment to the AC outlet on the rear panel
if that equipment requires more power than the outlet is rated to
provide.
13.Voltage Selector (General Model only)
The voltage selector on the rear panel of this unit must be set
for your local main voltage BEFORE plugging into the AC
main supply.
Voltages are 110/120/220/240V AC, 50/60 Hz.
IMPORTANT
Please record the serial number of this unit in the space below.
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future reference.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
For U.K. customers
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an
appropriate 3 pin plug fitted. For details, refer to the
instructions described below.
Note: The plug severed from the mains lead must be
destroyed, as a plug with bared flexible cord is hazardous if
engaged in a live socket outlet.
SPECIAL INSTRUCTIONS FOR U.K. MODEL
IMPORTANT:
The wire in the mains lead are coloured in accordance with
the following code:
Blue: NEUTRAL
Brown: LIVE
The colours of the wires in the mains lead of this apparatus
may not correspond with the coloured markings identifying
the terminals in your plug. Proceed as follows: the wire
which is coloured BLUE must be connected to the terminal
which is marked with the letter N or coloured BLACK. The
wire which is coloured BROWN must be connected to the
terminal which is marked with the letter L or coloured RED.
Making sure that neither core is connected to the earth
terminal of the three pin plug.
3
English
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
Thank you for selecting this YAMAHA stereo amplifier
●
55W
+
55W (8Ω) RMS Output Power, 0.04% THD,
20
–
20,000 Hz
●
High Dynamic Power, Low Impedance Drive
Capability
●
Continuously Variable Loudness Control
●
CD Direct Switch to Reproduce the Purest CD
Sound
●
Remote Control Capability
Supplied Accessories .....................................................2
Caution ...........................................................................3
Connections ...................................................................4
Operations ......................................................................6
Remote Control Transmitter ...........................................9
Notes about the Remote Control Transmitter ...............10
Troubleshooting ............................................................11
Specifications ...............................................................12
FEATURES CONTENTS
The apparatus is not disconnected from the AC power
source as long as it is connected to the wall outlet, even if
the apparatus itself is turned off.
4
CONNECTIONS
• Before attempting to make any connections to or from this unit, be sure to first switch OFF the power to this unit and to any other
components to which connections are being made.
• When making connections between this unit and other components, be sure all connections are made correctly, that is to say L
(left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this
unit.
* : Refer to “ABOUT THE ACCESSORY
TERMINALS” on page 5.
OUTPUT
GND
REMOTE
CONTROL
AUDIO OUT
LINE OUT
LINE IN
OUTPUT
OUTPUT
LINE IN
Turntable
Video cassette player,
LD player, etc.
Tape deck 2 Speakers A
Right Left
To AC outlet
Compact disc player Tuner Tape deck 1 Speakers B
Right
Left
CD PHONO TUNER AUX TAPE
PB
REC
OUT
TAPE
PB
REC
OUT
TAPE 1 TAPE 2
REMOTE
CONTROL
PHONO
SPEAKER AC OUTLETS
R L
A
B
R
L
+-- +--
LINE OUT
(Europe model)
GND
100W MAX. TOTAL
SWITCHED
Video cassette player,
LD player, etc.
5
English
Connect the SPEAKERS terminals to your speakers with wire
of the proper gauge, cut to be as short as possible. If the
connections are faulty, no sound will be heard from the
speakers. Make sure that the polarity of the speaker wires is
correct, that is, + and – markings are observed. If these wires
are reversed, the sound will be unnatural and will lack bass.
Do not let the bare speaker wires touch each other and do
not let them touch the metal parts of this unit as this could
damage this unit and/or speakers.
How to Connect:
Red: positive (+)
Black: negative (–)
➀
Unscrew the knob.
➁
Insert the bare wire.
[Remove approx. 5mm
(1/4”) insulation from
the speaker wires.]
➂
Tighten the knob and
secure the wire.
●
One or two speaker systems can be connected to this unit.
If you connect only one speaker system, connect it to either
the SPEAKERS A or B terminals.
●
Use speakers with the specified impedance shown on the
rear of this unit.
●
Banana Plug connections are also possible (except for
Scandinavian model). Simply insert the Banana Plug
connector into the corresponding terminal.
CONNECTING SPEAKERS
ABOUT THE ACCESSORY TERMINALS
AC OUTLET(S)
(Europe and General models)
............................................................3 SWITCHED OUTLETS
(Australia and U.K. models)
...............................................................1 SWITCHED OUTLET
Use these to connect the power cords from your components
to this unit.
The power to the SWITCHED outlets is controlled by this unit’s
POWER switch or the provided remote control transmitter’s
POWER key. These outlets will supply power to any
component whenever this unit is turned on.
The maximum power (total power consumption of
components) that can be connected to the SWITCHED AC
OUTLET(S) is 100 watts.
REMOTE CONTROL (PHONO) connector
If you have a YAMAHA turntable with a terminal for remote
control, connect it to this connector by using the cable provided
with the turntable. This connection allows you to control the
turntable from the provided remote control transmitter.
GND terminal (For turntable use)
Connecting the ground wire of the turntable to this terminal will
normally minimize hum, but in some cases better results may
be obtained with the ground wire disconnected.
1
2
3
6
1
Set to the “
∞
” position.
2
3
Select a desired input source.
* The indicator corresponding to the selected input source
will illuminate.
* Note that pressing on each input selector button selects
the source which is connected to the corresponding input
terminals on the rear panel.
4
Select the speakers to be used.
* If you use two speaker systems, press both the A and B
switches.
5
Play the source.
6
Adjust to the desired output level.
7
If desired, adjust the BASS, TREBLE, BALANCE and
LOUDNESS controls, etc. (Refer to page 8.)
Notes
●
If you select AUX, TUNER, CD or PHONO, be sure that
TAPE 1 and/or TAPE 2 are not being selected.
●
If you select TAPE 1 and TAPE 2 at the same time, the
result will be the sound from the tape deck 1.
●
For TAPE 1 and TAPE 2, whenever the button is pressed,
the corresponding input source is selected or canceled
alternately.
OPERATIONS
TO PLAY A SOURCE
TAPE 1
MONITOR
COPY
INPUT
AUX
TUNER
CD
PHONO
TAPE 2
SPEAKERS
A
B
ON
OFF
ON
OFF
— dB
VOLUME
0
POWER
0
— dB
VOLUME
∞
∞
2
3
4
7
1, 6
7
English
1
Select the source to be recorded.
* To dub from tape to tape, refer to the “Notes” shown at
right.
* When you select AUX, TUNER, CD or PHONO, be sure
that TAPE 1 and/or TAPE 2 are not also selected.
2
Play the source and then turn the VOLUME control up
to confirm the input source.
3
Begin recording on the tape deck.
4
To monitor the audio signals being recorded, press the
input selector button for the tape deck being used to
make the recording.
SOURCE
Tape deck connected to
the TAPE 2 terminals.
RECORDER
Tape deck connected to
the TAPE 1 terminals.
Notes
●
VOLUME, BASS, TREBLE, BALANCE and LOUDNESS
control settings have no effect on the material being
recorded.
●
To dub from tape to tape, only the following method of
dubbing can be performed.
TO RECORD A SOURCE TO TAPE
→
TAPE 1
MONITOR
COPY
INPUT
AUX
TUNER
CD
PHONO
TAPE 2
TAPE 1
MONITOR
COPY
INPUT
AUX
TUNER
CD
PHONO
TAPE 2
1, 4
2
Using the CD DIRECT switch
You can enjoy the purest possible sound from your CD input
source by setting this switch ON. By doing so, the CD audio
signal bypasses the BASS, TREBLE, BALANCE and
LOUDNESS controls, eliminating any alterations to the audio
signal.
When you listen with headphones
Connect the headphones to the PHONES jack. When listening
with headphones privately, set both the SPEAKERS A and B
switches to the OFF position.
8
Adjusting the BASS and TREBLE
controls
Adjusting the BALANCE control Selecting the SPEAKER system
Adjust the balance of the output volume to the left and right
speakers to compensate for sound imbalance caused from
speaker location or listening room conditions.
Because one or two speaker systems can be connected to this
unit, the SPEAKERS switches allow you to select speaker
system A or B, or both at once.
BASS : Turn this clockwise to increase (or counter-
clockwise to decrease) the low frequency
response.
TREBLE : Turn this clockwise to increase (or counter-
clockwise to decrease) the high frequency
response.
Adjusting the continuously variable
LOUDNESS control
This control provides compensation for the human ears’ loss of
sensitivity to high and low-frequency ranges at low volume.
This control is adjustable to retain full tonal range at any
volume level.
1
Set to the “FLAT” position.
2
Set to the loudest listening level that
you would listen to.
3
Turn so that the desired volume can
be achieved.
BALANCE
0
L 5
5 R
BASS
—
5 +
5
0
LOUDNESS
FLAT
—
30dB
I0
0
— dB
VOLUME
LOUDNESS
FLAT
—
30dB
I0
SPEAKERS
A
B
ON
OFF
ON
OFF
PHONES
CD DIRECT
∞
TREBLE
—
5 +
5
0
9
English
REMOTE CONTROL TRANSMITTER
The remote control transmitter provided with this unit is designed to control all the most commonly used functions of the unit. If the
CD player, tuner, turntable and tape deck connected to this unit are YAMAHA components, then this remote control transmitter will
also control various functions of each component.
KEY FUNCTIONS
For Control of This Unit
For Other Component Control
Identify the remote control transmitter keys with your component’s keys. If these keys are identical, their function will be the
same. On each key function, refer to the corresponding instruction on your component’s manual.
STANDBY mode (Europe model only)
While the power is on, pressing the POWER key on the remote
control transmitter switches the unit to the STANDBY mode.
(In this mode, the indicator is half illuminated.)
POWER
PLAY/CUT
PHONO
SKIP PLAY CD
SEARCH PAUSE/STOP DISC SKIP
—
+
A/B/C/D/E
TUNER
DIR A
DECK A/B
DIR B TAPE 1
TAPE 2
REC/PAUSE
STOP
REC MUTE
AUX
VOLUME
—
+
PRESET
PLAY
POWER
PLAY/CUT
PHONO
SKIP PLAY CD
SEARCH PAUSE/STOP DISC SKIP
—
+
A/B/C/D/E
TUNER
DIR A
DECK A/B
DIR B TAPE 1
TAPE 2
REC/PAUSE
STOP
REC MUTE
AUX
VOLUME
—
+
PRESET
PLAY
Turns the power on/off.
Selects input source.
Turns the volume level up/down.
Controls compact disc player.
* DISC SKIP is applicable only to
compact disc changer.
Controls tuner
* + : Selects higher preset station
number.
– : Selects lower preset station number.
A/B/C/D/E: Selects the page (A – E) of
preset stations.
Controls tape deck.
* DIR A, B and DECK A/B are
applicable only to double
cassette tape deck.
* For a single cassette deck with
automatic reverse function,
pressing DIR A will reverse the
direction of tape running.
Starts/stops record play on turntable.
POWER POWER
POWER on mode
STANDBY mode
• •
10
NOTES ABOUT THE REMOTE CONTROL TRANSMITTER
Battery installation
Battery replacement
If you find that the remote control transmitter must be used
closer to the main unit, the batteries are weak. Replace both
batteries with new ones.
Notes
●
Use only AA, R6, UM-3 batteries for replacement.
●
Be sure the polarities are correct. (See the illustration inside
the battery compartment.)
●
Remove the batteries if the remote control transmitter will
not be used for an extended period of time.
●
If batteries leak, dispose of them immediately. Avoid
touching the leaked material or letting it come in contact with
clothing, etc. Clean the battery compartment thoroughly
before installing new batteries.
Remote control transmitter operation range
Notes
●
There should be no large obstacles between the remote
control transmitter and the main unit.
●
If the remote control sensor is directly illuminated by strong
lighting (especially an inverter type of fluorescent lamp etc.),
it might cause the remote control transmitter not to work
correctly. In this case, reposition the main unit to avoid
direct lighting.
2
3
1
30°
30°
Remote control
sensor
Within approximately
7 m (23 feet)
11
English
If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple
measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and
contact your authorized YAMAHA dealer or service center for help.
TROUBLESHOOTING
SYMPTOM
The unit fails to turn on when the POWER
switch is pressed.
No sound.
The sound suddenly goes off.
Only one side speaker outputs the sound.
There is a lack of bass, and no ambience.
Sound “hums”.
Sound level is low.
Using the BASS, TREBLE, BALANCE and
LOUDNESS controls does not affect the
tone of CD input source.
The volume level cannot be increased, or
sound is distorted.
The remote control transmitter does not
work.
CAUSE
Power cord is not plugged in or is not
completely inserted.
Incorrect output cord connections.
Appropriate input source is not selected.
Speaker connections are not secure.
The protection circuit has activated because
of short circuit etc.
Incorrect setting of the BALANCE control.
Incorrect cord connections.
The + and – wires are connected in reverse
at the amplifier or speakers.
Incorrect cord connections.
No connection from the turntable to the GND
terminal.
The LOUDNESS control is functioning.
The CD DIRECT switch is ON.
The power to the component connected to
the REC OUT terminals of this unit is off.
Direct sunlight or lighting (of an inverter type
of flourescent lamp etc.) is striking the
remote control sensor of the main unit.
The batteries of this remote control
transmitter are too weak.
REMEDY
Firmly plug in the power cord.
Connect the cords properly. If the problem
persists, the cords may be defective.
Select an appropriate input source with the
input selector buttons.
Secure the connections.
Turning the unit off and then on will reset the
protection circuit.
Adjust it to the appropriate position.
Connect the cords properly. If the problem
persists, the cords may be defective.
Connect the speaker wires in the correct
phase (+ and –).
Firmly connect the audio plugs. If the
problem persists, the cords may be defective.
Make the GND connection between the
turntable and this unit.
Set the LOUDNESS control to the FLAT
position.
The CD DIRECT switch must be switched
OFF to use those controls.
Turn the power to the component on.
Change position of the main unit.
Replace the batteries with new ones.
12
SPECIFICATIONS
Minimum RMS Output Power per Channel
8 ohms, 20 Hz to 20 kHz, 0.04% THD....................55W+55W
6 ohms, 20 Hz to 20 kHz, 0.06% THD
[Except Scandinavia model].................................60W+60W
Dynamic Power per Channel
(by IHF Dynamic Headroom measuring method)
8/6/4/2 ohms...............................................78/90/110/120W
DIN Standard Output Power per Channel
(4 ohms, 1 kHz, 0.7% THD)
[Europe model only].......................................................85W
IEC Power (8 ohms, 1 kHz, 0.04% THD)
[Europe model only].........................................................70W
Damping Factor
8 ohms, 20 Hz to 20 kHz...................................................100
Input Sensitivity/Impedance
PHONO MM...............................................2.5 mV/47 k-ohms
TAPE/AUX/TUNER/CD
..............................150 mV/47 k-ohms
Maximum Input Signal (1 kHz, 0.01% THD)
PHONO MM..................................................................80 mV
Headphone Jack Rated Output/ Impedance
(8 ohms, 20 Hz to 20 kHz, 0.04% THD)
Output Level ................................................................0.42V
Impedance.............................................................390 ohms
Frequency Response (20 Hz to 20 kHz)
TAPE/AUX/TUNER/CD
..............................................0±0.5 dB
RIAA Equalization Deviation (20 Hz to 20 kHz)
PHONO MM..............................................................0±0.5 dB
Total Harmonic Distortion (20 Hz to 20 kHz)
PHONO MM to REC OUT (1V)
........................................
0.02%
TAPE/AUX/TUNER/CD
to SP OUT
(27.5W/8 ohms) ..........................................................0.02%
Signal-to-Noise Ratio (IHF-A Network)
PHONO MM (5 mV Input Shorted) ............................... 82 dB
TAPE/AUX/TUNER/CD (Input Shorted)
........................ 105 dB
Residual Noise (IHF-A Network)....................................100 µV
Channel Separation (Vol. –30 dB)
PHONO MM (Input Shorted 1 kHz)................................65 dB
TAPE/AUX/TUNER/CD
(Input 5.1 k-ohms Terminated 1 kHz)
.......................................................................................60 dB
Tone Control Characteristics
BASS: Boost/cut.....................................±10 dB (50 Hz)
(Turnover frequency) ............................(350 Hz)
TREBLE: Boost/cut...................................±10 dB (20 kHz)
(Turnover frequency)............................(3,5 kHz)
Continuous Loudness Control
Attenuation......................................................–30 dB (1 kHz)
(Level related equalization)
Power Supply
[Australia and U.K. models] ...........................AC 240V, 50 Hz
[Europe model] ..............................................AC 230V, 50 Hz
[General model] ...................AC 110/120/220/240V, 50/60 Hz
Power Consumption
[Scandinavia model].......................................................130W
[Australia, U.K., Europe (except Scandinavia) and General
models] ..........................................................................150W
AC Outlets
3 SWITCHED OUTLETS
[Europe and General models]....................100W max. total
1 SWITCHED OUTLET
[Australia and U.K. models] .......................100W max. total
Dimensions (W x H x D)............................435 x 126 x 308 mm
(17-1/8” x 4-15/16” x 12-1/8”)
Weight
[Australia, U.K. and General models] .....6.6 kg (14 lbs. 8 oz.)
[Europe model] ..........................................7 kg (15 lbs. 6 oz.)
Accessories.....................................Remote control transmitter
Batteries
Specifications subject to change without notice.
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, D-2084 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. 17 RUE DES CAMPANULES, LOGNES 77321 MARNE LA VALLEE CEDEX 2, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
VR 35210
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
Yamaha AX-55 Manuale del proprietario
- Categoria
- Amplificatori audio
- Tipo
- Manuale del proprietario
in altre lingue
- English: Yamaha AX-55 Owner's manual
- français: Yamaha AX-55 Le manuel du propriétaire
- español: Yamaha AX-55 El manual del propietario
- Deutsch: Yamaha AX-55 Bedienungsanleitung
- русский: Yamaha AX-55 Инструкция по применению
- Nederlands: Yamaha AX-55 de handleiding
- português: Yamaha AX-55 Manual do proprietário
- dansk: Yamaha AX-55 Brugervejledning
- čeština: Yamaha AX-55 Návod k obsluze
- polski: Yamaha AX-55 Instrukcja obsługi
- svenska: Yamaha AX-55 Bruksanvisning
- Türkçe: Yamaha AX-55 El kitabı
- suomi: Yamaha AX-55 Omistajan opas
- română: Yamaha AX-55 Manualul proprietarului
Documenti correlati
-
Yamaha 401 Manuale del proprietario
-
-
Yamaha Audio RX-V385 Manuale utente
-
-
-
-
-
-