Pioneer X-HM51 Manuale utente

X-HM51-K/-S

CD Receiver System | Micro chaîne CD | CD-Receiversystem |

Sistema CD con amplificatore | CD Receiver System |

Sistema receptor de CD | Система ресивера CD

XC-HM51-K/-S

CD Receiver | Micro chaîne CD | CD-Receiver |

Ricevitore CD | CD-Receiver | Receptor de CD | CD-Ресивер

Operating Instructions

Mode d’emploi

Bedienungsanleitung

Istruzioni per l’uso

Handleiding

Manual de instrucciones

Инструкции по эксплуатации

;+0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸱᭶㸰㸶᪥ࠉᮌ᭙᪥ࠉ༗ᚋ㸰᫬㸯ศ

CAUTION

TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

D3-4-2-1-1_B1_En

WARNING

This equipment is not waterproof. To prevent a fire or

shock hazard, do not place any container filled with

liquid near this equipment (such as a vase or flower

pot) or expose it to dripping, splashing, rain or

moisture.

D3-4-2-1-3_A1_En

WARNING

To prevent a fire hazard, do not place any naked flame

sources (such as a lighted candle) on the equipment.

D3-4-2-1-7a_A1_En

VENTILATION CAUTION

When installing this unit, make sure to leave space

around the unit for ventilation to improve heat radiation

(at least 25 cm at top, 10 cm at rear, and 5 cm at each

side).

WARNING

Slots and openings in the cabinet are provided for

ventilation to ensure reliable operation of the product,

and to protect it from overheating. To prevent fire

hazard, the openings should never be blocked or

covered with items (such as newspapers, table-cloths,

curtains) or by operating the equipment on thick carpet

or a bed.

D3-4-2-1-7b*_A1_En

Operating Environment

Operating environment temperature and humidity:

+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH

(cooling vents not blocked)

Do not install this unit in a poorly ventilated area, or in

locations exposed to high humidity or direct sunlight

(or strong artificial light)

D3-4-2-1-7c*_A1_En

WARNING

Store small parts out of the reach of children and

infants. If accidentally swallowed, contact a doctor

immediately.

D41-6-4_A1_En

This product is for general household purposes. Any

failure due to use for other than household purposes

(such as long-term use for business purposes in a

restaurant or use in a car or ship) and which requires

repair will be charged for even during the warranty

period.

K041_A1_En

CAUTION

The STANDBY/ON switch on this unit will not

completely shut off all power from the AC outlet.

Since the power cord serves as the main disconnect

device for the unit, you will need to unplug it from the

AC outlet to shut down all power. Therefore, make

sure the unit has been installed so that the power

plug can be easily unplugged from the AC outlet in

case of an accident. To avoid fire hazard, the power

cord should also be unplugged from the AC outlet

when left unused for a long period of time (for

example, when on vacation).

D3-4-2-2-2a*_A1_En

POWER-CORD CAUTION

Handle the power cord by the plug. Do not pull out the

plug by tugging the cord and never touch the power

cord when your hands are wet as this could cause a

short circuit or electric shock. Do not place the unit, a

piece of furniture, etc., on the power cord, or pinch the

cord. Never make a knot in the cord or tie it with other

cords. The power cords should be routed such that they

are not likely to be stepped on. A damaged power cord

can cause a fire or give you an electrical shock. Check

the power cord once in a while. When you find it

damaged, ask your nearest PIONEER authorized service

center or your dealer for a replacement.

S002*_A1_En

Do not install your speakers overhead on the ceiling or

wall. The grill is designed to be detachable, and as such

it may fall and cause damage or personal injury if

installed overhead.

SGK004_A1_En

CAUTION

This product is a class 1 laser product classified

under the Safety of laser products, IEC 60825-1:2007.

CLASS 1 LASER PRODUCT

D58-5-2-2a_A1_En

X-HM51 only

;+0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸱᭶㸰㸶᪥ࠉᮌ᭙᪥ࠉ༗ᚋ㸰᫬㸯ศ

Information for users on collection and disposal of old equipment and used batteries

These symbols on the products, packaging, and/or accompanying documents mean

that used electrical and electronic products and batteries should not be mixed with

general household waste.

For proper treatment, recovery and recycling of old products and used batteries,

please take them to applicable collection points in accordance with your national

legislation.

By disposing of these products and batteries correctly, you will help to save valuable

resources and prevent any potential negative effects on human health and the

environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products and batteries,

please contact your local municipality, your waste disposal service or the point of sale

where you purchased the items.

These symbols are only valid in the European Union.

For countries outside the European Union:

If you wish to discard these items, please contact your local authorities or dealer and

ask for the correct method of disposal.

K058a_A1_En

Symbol examples

for batteries

Symbol for

equipment

Pb

Radio wave caution

This unit uses a 2.4 GHz radio wave frequency, which is

a band used by other wireless systems (Microwave

ovens and Cordless phones, etc.). In this event noise

appears in your television image, there is the possibility

this unit (including products supported by this unit) is

causing signal interference with the antenna input

connector of your television, video, satellite tuner, etc. In

this event, increase the distance between the antenna

input connector and this unit (including products

supported by this unit).

• Pioneer is not responsible for any malfunction of the

compatible Pioneer product due to communication

error/malfunctions associated with your network

connection and/or your connected equipment.

Please contact your Internet service provider or

network device manufacturer.

• A separate contract with/payment to an Internet

service provider is required to use the Internet.

;+0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸱᭶㸰㸶᪥ࠉᮌ᭙᪥ࠉ༗ᚋ㸰᫬㸯ศ

4

En

Thank you for buying this Pioneer product.

Please read through these operating instructions so that you will know how to operate your model properly. After you

have finished reading the instructions, put them in a safe place for future reference.

Contents

01 Before you start

What’s in the box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Loading the batteries in the remote control . . . . . . . . . 5

Using the remote control . . . . . . . . . . . . . . . . . . . . . . . . . 5

02 Part names and functions

Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Detatching and replacing the front grille

(X-HM51 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

03 Connections

Speaker connection (X-HM51 only) . . . . . . . . . . . . . . . 10

Using other subwoofer . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Connecting antennas . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Using external antennas . . . . . . . . . . . . . . . . . . . . . . . . . 12

Plugging in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

04 Getting started

To turn the power on . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

General control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Input function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Display brightness control . . . . . . . . . . . . . . . . . . . . . . . 13

Volume auto setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Volume control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Muting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Sound controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Equalizer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

P.BASS control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Bass/treble control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Setting the wake-up timer . . . . . . . . . . . . . . . . . . . . . . . 14

Calling the wake-up timer . . . . . . . . . . . . . . . . . . . . . . . . 15

Cancelling the wake-up timer. . . . . . . . . . . . . . . . . . . . . 15

Using the wake-up timer. . . . . . . . . . . . . . . . . . . . . . . . . 15

Using the sleep timer . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Using Headphones . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

05 iPod/iPhone/iPad playback

Confirming what iPod/iPhone/iPad models are

supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Connecting your iPod/iPhone/iPad . . . . . . . . . . . . . . . 16

Connecting iPod/iPhone/iPad using supplied iPad

stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Playing iPod/iPhone/iPad . . . . . . . . . . . . . . . . . . . . . . . 17

06 Disc playback

Playing discs or files . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Advanced CD or MP3/WMA disc playback . . . . . . . . . 19

Direct track search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Repeat play. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Random play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Programmed play (CD or MP3/WMA) . . . . . . . . . . . . . . 20

About downloading MP3/WMA . . . . . . . . . . . . . . . . . . . 20

About folder playback order . . . . . . . . . . . . . . . . . . . . . . 20

Specify the folder to play. . . . . . . . . . . . . . . . . . . . . . . . . 21

Switch the display contents . . . . . . . . . . . . . . . . . . . . . . 21

07 USB playback

Playing USB storage devices . . . . . . . . . . . . . . . . . . . . 22

Repeat play. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Random play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Specify the folder to play. . . . . . . . . . . . . . . . . . . . . . . . . 23

Switch the display contents . . . . . . . . . . . . . . . . . . . . . . 23

Playing in the desired order (Programmed Play) . . . . 23

08 Using the tuner

Listening to the radio broadcasts . . . . . . . . . . . . . . . . 24

Tuning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Saving station presets. . . . . . . . . . . . . . . . . . . . . . . . . . . 24

To recall a memorised station . . . . . . . . . . . . . . . . . . . . 25

To scan the preset stations. . . . . . . . . . . . . . . . . . . . . . . 25

To erase entire preset memory. . . . . . . . . . . . . . . . . . . . 25

Changing the noise cut mode . . . . . . . . . . . . . . . . . . . . 25

Using the Radio Data System (RDS) . . . . . . . . . . . . . . 25

An introduction to RDS. . . . . . . . . . . . . . . . . . . . . . . . . . 25

Searching for RDS programs. . . . . . . . . . . . . . . . . . . . . 25

Information provided by RDS . . . . . . . . . . . . . . . . . . . . . 26

Using the Auto Station Program Memory (ASPM). . . . 26

Notes for RDS operation. . . . . . . . . . . . . . . . . . . . . . . . . 26

09 Other connections

Connecting auxiliary components . . . . . . . . . . . . . . . . 27

10

Bluetooth

® Audio playback

Music playback using Bluetooth wireless

technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Pairing with the unit (Initial registration) . . . . . . . . . . 28

Listen to music on the unit from a Bluetooth capable

device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Radio wave caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Scope of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Radio wave reflections . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Precautions regarding connections to products

supported by this unit . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

11 Additional information

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Playable discs and formats . . . . . . . . . . . . . . . . . . . . . 34

Regarding copy protected CDs . . . . . . . . . . . . . . . . . . . 34

Supported audio file formats . . . . . . . . . . . . . . . . . . . . . 34

Cautions on use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

When moving this unit . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Place of installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Do not place objects on this unit . . . . . . . . . . . . . . . . . . 35

About condensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Cleaning the product. . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Cleaning the lens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Handling discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Storing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Cleaning discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

About specially shaped discs. . . . . . . . . . . . . . . . . . . . . 35

About iPod/iPhone/iPad . . . . . . . . . . . . . . . . . . . . . . . . 36

Restoring all the settings to the defaults . . . . . . . . . . 36

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

;+0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸱᭶㸰㸶᪥ࠉᮌ᭙᪥ࠉ༗ᚋ㸰᫬㸯ศ

Before you start 01

5

En

English Français Español

Chapter 1:

Before you start

What’s in the box

Please confirm that the following accessories are in the box

when you open it.

• Remote control

•Power cord

• AM antenna cable

• FM wire antenna

• AAA batteries (R03) x 2

• Speaker cord x 2 (X-HM51 only)

•iPad stand

• Warranty card

• Operating instructions (this document)

Loading the batteries in the

remote control

1 Open the rear lid and load the batteries as

illustrated below.

2 Close the rear lid.

CAUTION

• When inserting the batteries, make sure not to damage

the springs on the battery’s terminals. This can cause

batteries to leak or over heat.

• Do not use any batteries other than the ones specified.

Also, do not use a new battery together with an old one.

• When loading the batteries into the remote control, set

them in the proper direction, as indicated by the polarity

marks ( and ).

• Do not heat batteries, disassemble them, or throw them

into flames or water.

• Batteries may have different voltages, even if they are the

same size and shape. Do not use different types of

batteries together.

• To prevent leakage of battery fluid, remove the batteries

if you do not plan to use the remote control for a long

period of time (1 month or more). If the fluid should leak,

wipe it carefully off the inside of the case, then insert

new batteries. If a battery should leak and the fluid

should get on your skin, flush it off with large quantities

of water.

• When disposing of used batteries, please comply with

governmental regulations or environmental public

institution’s rules that apply in your country/area.

• WARNING

Do not use or store batteries in direct sunlight or other

excessively hot place, such as inside a car or near a

heater. This can cause batteries to leak, overheat,

explode or catch fire. It can also reduce the life or

performance of batteries.

Using the remote control

The remote has a range of about 7 m at an angle of about 30º

from the remote sensor.

Keep in mind the following when using the remote control:

• Make sure that there are no obstacles between the

remote and the remote sensor on the unit.

• Remote operation may become unreliable if strong

sunlight or fluorescent light is shining on the unit’s

remote sensor.

• Remote controllers for different devices can interfere

with each other. Avoid using remotes for other

equipment located close to this unit.

• Replace the batteries when you notice a fall off in the

operating range of the remote.

INPUT

30°

7 m

30°

;+0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸱᭶㸰㸶᪥ࠉᮌ᭙᪥ࠉ༗ᚋ㸰᫬㸯ศ

Part names and functions02

6

En

Chapter 2:

Part names and functions

Remote control

1 1 STANDBY/ON

Switches the receiver between standby and on (page 13).

2 Input function buttons

Use to select the input source to this receiver (pages 17, 18,

22, 24, 27 and 28).

3 CD Receiver control buttons

CLOCK/TIMER

Use for setting the clock, as well as for setting and

checking the timers (page 13).

SLEEP

See Using the sleep timer on page 15.

4 Numeric buttons (0 to 9)

Use to enter the number (page 19).

5

CLEAR

Use to clear the programmed play (page 20).

6 CD Receiver control buttons

DISPLAY

Press to change the display for songs playing back from

CD or USB (page 21).

FOLDER

Use to select the folder of the MP3/WMA disc or USB

mass storage device (page 20).

MENU

Use to access the menu.

MEMORY/PROGRAM

Use to memory or program the MP3/WMA disc

(page 20).

7

F

/

G

/

H

/

I

(TUNE +/–), ENTER

Use to select/switch system settings and modes, and to

confirm actions.

Use TUNE +/– can be used to find radio frequencies

(page 24).

8

PRESET +/–

Use to select preset radio stations (page 25).

9

MUTE

Mutes/unmutes the sound (page 13).

10 Playback control buttons

Use to control each function after you have selected it using

the input function buttons (page 18).

4

5

1

3

2

6

7

8

12

17

13

14

9

10

11

16

15

STANDBY/ON





CD USB TUNER AUDIO IN

DISPLAY FOLDER

MENU

PRESET VOLUME

ST/MONO ASPM PTY DISPLAY

+

MUTE

TUNE–

TUNE+

DIMMER

 







–

+

–

MEMORY

/PROGRAM

123

456

789

0

BT AUDIO

CLOCK/TIMER

SLEEP

EQUALIZER

P. BA SS

BASS/TREBLE

RANDOM

CLEAR REPEAT

OPEN/CLOSE

RDS

ENTER

OPTION

;+0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸱᭶㸰㸶᪥ࠉᮌ᭙᪥ࠉ༗ᚋ㸰᫬㸯ศ

Part names and functions 02

7

En

English Français Español

11

Tuner

control buttons

ST/MONO

Use to switch the sound mode between stereo and

monaural. (page 24)

RDS ASPM

Use to search for RDS Auto station program memory

(page 25).

RDS PTY

Use to search for RDS program types (page 25).

RDS DISPLAY

Press to change the RDS display for information mode

(page 25).

12 OPEN/CLOSE

Use to open or close the disc tray (page 18).

13 Sound control buttons

Adjust the sound quality (page 14).

14 RANDOM

Randomize order of track playback from a CD, iPod or USB

(page 19).

15

REPEAT

Press to change the repeat play setting from a CD, iPod or

USB (page 19).

16 Volume control buttons

Use to set the listening volume (page 13).

17

DIMMER

Dims or brightens the display. The brightness can be

controlled in four steps (page 13).

Note

The OPTION buttons are not available for this unit.

Detatching and replacing the front

grille (X-HM51 only)

The front grille of this speaker system is removable. Proceed

as follows:

1 Grab the bottom of the grille, and gently

pull it toward you to remove the bottom

portion.

2 Next, grab the top part of the grille and

gently pull it toward you to remove the top

portion.

3 To install the grille, align the projections on

the speaker with the receptacles on the top and

at the base of the grille and push them into

place.

;+0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸱᭶㸰㸶᪥ࠉᮌ᭙᪥ࠉ༗ᚋ㸰᫬㸯ศ

Part names and functions02

8

En

Front panel

1 1 STANDBY/ON button

Switches the receiver between standby and on (page 13).

2 Remote sensor

Receives the signals from the remote control.

3TIMER

indicator

Lights when the unit power is off but when the timer setting is

activated.

4 Character display

See Display on page 9.

5 Volume control

Use to set the listening volume (page 13).

6 INPUT button

Selects the input source.

7 Headphone socket

Use to connect headphones. When the headphones are

connected, there is no sound output from the speakers

(page 15).

8 AUDIO IN socket

Use to connect an auxiliary component using a stereo

minijack cable (page 27).

9 USB terminal

Use to connect your USB mass storage device or Apple iPod/

iPhone/iPad as an audio source (pages 17 and 22).

10 Disc tray

Place the disc, label side up (page 18).

11 Playback control buttons

Select the desired track or file to be played back. Stop current

playback. Stop playback or resume playback from the point

where it was paused.

12 Disc tray open/close button

Use to open or close the disc tray (page 18).

 STANDBY/ON

INPUT

VOLUME

PHONES AUDIO IN

  

TIMER

7 86 9 11 1210

2 51 3 4

;+0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸱᭶㸰㸶᪥ࠉᮌ᭙᪥ࠉ༗ᚋ㸰᫬㸯ศ

Part names and functions 02

9

En

English Français Español

Display

1

Lights when the sound is muted.

Note

• The mute icon will be displayed in red.

2

Start playback.

3 !

Pause playback.

4

Timer function is set.

5 Character display

Displays various system information.



1 32 4

5

;+0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸱᭶㸰㸶᪥ࠉᮌ᭙᪥ࠉ༗ᚋ㸰᫬㸯ศ

Connections03

10

En

Chapter 3:

Connections

CAUTION

• Be sure to turn off the power and unplug the power cord

from the power outlet whenever making or changing

connections.

• Connect the power cord after all the connections

between devices have been completed.

Speaker connection (X-HM51 only)

• The provided speaker wire with the red tube is for the (+)

terminal. Connect the wire with red tube the (+)

terminal, and other wire to the (–) terminal.

CAUTION

• These speaker terminals carry HAZARDOUS LIVE

voltage. To prevent the risk of electric shock when

connecting or disconnecting the speaker cables,

disconnect the power cord before touching any

uninsulated parts.

• Make sure that the speaker cable cores do not become

exposed and make contact with other cable cores. This

may cause malfunction of the product.

• Do not allow the speaker cable core to come into contact

with the receiver body.

- If the speaker cable core comes into contact with any

metal portion of the receiver’s body, it may damage the

speakers and cause smoke and fire.

Insert speaker cables securely into the terminals and

check that the cable does not come out of easily.

X-HM51 only

• Do not connect any speakers other than those supplied

to this system.

• Do not connect the supplied speakers to any amplifier

other than the one supplied with this system.

Connection to any other amplifier may result in

malfunction or fire.

• Do not attach these speakers to the wall or ceiling. They

may fall off and cause injury.

• These speakers are magnetically shielded. However,

depending on the installation location, color distortion

may occur if the speaker system is installed extremely

close to the screen of a television set. If this happens,

turn off the television set, and then turn it on after 15 to

30 minutes. If the problem persists, move the speaker

system away from the television set.

XC-HM51 only

• You can use speakers with a nominal impedance

between 4 : and 16 :.

Note

• There is no difference between L and R speakers.

Cleaning the glossy finish of the speaker (X-HM51

only)

• If you use a dusty or hard cloth or if you rub the screen

hard, the finish of the product will be scratched.

• If you clean the surface of the speaker system with a wet

cloth, water droplets on the surface may enter into the

product, resulting in malfunction.

• When cleaning the finish of the speaker system, gently

wipe it with a dry soft cloth.

SUBWOOFER

PREOUT

SPEAKERS

RL

+

X-HM51

This unit’s rear panel

Red tube

Supplied

speaker wire

Left speakerRight speaker

;+0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸱᭶㸰㸶᪥ࠉᮌ᭙᪥ࠉ༗ᚋ㸰᫬㸯ศ

Connections 03

11

En

English Français Español

If not using the provided speaker wire

1 Twist exposed wire strands together.

2 Loosen terminal and insert exposed wire.

3 Tighten terminal.

X-HM51 only

• Do not install your speakers overhead on the ceiling or wall.

The grill is designed to be detachable, and as such it may

fall and cause damage or personal injury if installed

overhead.

• Do not allow any objects to fall into or to be placed in the

bass reflex ducts.

• Do not stand or sit on the speakers. You may be injured.

Using other subwoofer

You can connect a subwoofer with an amplifier to the

SUBWOOFER PREOUT socket.

Note

• No sound is heard from the subwoofer without a built-in

amplifier.

• Subwoofer Pre-out (audio signal): 350 mV / 10 k :at 70

Hz.

Connecting antennas

Connect the AM loop antenna and the FM wire antenna as

shown below. To improve reception and sound quality,

connect external antennas (see Using external antennas on

page 12).

1 Connect the AM antenna wires.

Hold the terminal part of the wire when connecting.

2 Fix the AM loop antenna to the attached

stand.

To fix the stand to the antenna, bend in the direction indicated

by the arrow (fig. a) then clip the loop onto the stand (fig. b).

3 Place the AM antenna on a flat surface and

in a direction giving the best reception.

4 Connect the FM wire antenna into the FM

antenna socket.

For best results, extend the FM antenna fully and fix to a wall

or door frame. Don’t drape loosely or leave coiled up.

To customers in Norway and Sweden

CAUTION

• “Apparater som er koplet til beskyttelsesjord via

nettplugg og/eller via annet jordtilkoplet utstyr - og er

tilkoplet et koaksialbasert kabel-TV nett, kan forårsake

brannfare. For å unngå dette skal det ved tilkopling av

apparater til kabel-TV nett installeres en galvanisk

isolator mellom apparatet og kabel-TV nettet.”

• “Apparater som är kopplade till skyddsjord via jordat

vägguttag och/eller via annan utrustning och samtidigt

är kopplad till kabel-TV nät kan i vissa fall medföra risk för

brand. För att undvika detta skall vid anslutning av

apparaten till kabel-TV nät galvanisk isolator finnas

mellan apparaten och kabel-TV nätet.

12 3

10 mm

AM

LOOP

ANTENNA

FM

UNBAL

75 Ω

LINE

IN

SUBWOOFER

PREOUT

L

R

This unit’s rear panel

Audio cable

(commercially available)

Commercially available

subwoofer (amplifier built in)

To audio input

socket

AM

LOOP

ANTENNA

FM

UNBAL

75 Ω

2

1

3

4

fig. a

fig. b

;+0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸱᭶㸰㸶᪥ࠉᮌ᭙᪥ࠉ༗ᚋ㸰᫬㸯ศ

Connections03

12

En

Using external antennas

To improve FM reception

Use a PAL connector (not supplied) to connect an external FM

antenna.

Plugging in

CAUTION

• Do not use any power cord other than the one supplied

with this unit.

• Do not use the supplied power cord for any purpose

other than that described below.

Before making or changing the connections, switch off the

power and disconnect the power cord from the AC outlet.

After you’ve finished making all connections, plug the unit

into an AC outlet.

ANTENNA

FM

UNBAL

75 Ω

One-touch PAL

connector

75 :coaxial

cable

AC IN

SPEAKER

R

To AC outlet

This unit’s rear panel

Power cord

;+0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸱᭶㸰㸶᪥ࠉᮌ᭙᪥ࠉ༗ᚋ㸰᫬㸯ศ

Getting started 04

13

En

English Français Español

Chapter 4:

Getting started

To turn the power on

Press the 1 STANDBY/ON to turn the power on.

After use:

Press the 1 STANDBY/ON to enter the power stand-by mode.

Note

• In standby mode, if iPod/iPhone/iPad is connected, the

unit turns charge mode.

Setting the clock

1 Press

1 STANDBY/ON

to turn the power on.

2 Press

CLOCK/TIMER

on the remote control.

“CLOCK” is shown on the main display.

3 Press

ENTER

.

4 Press

HI

to set the day, then press ENTER.

5 Press

HI

to set the hour, then press

ENTER.

6 Press

HI

to set the minute, then press

ENTER to confirm.

7 Press

ENTER

.

To confirm the time display:

Press the CLOCK/TIMER. The time display will appear for

about 10 seconds.

To readjust the clock:

Perform “Setting the clock” from step 1.

Note

• When power supply is restored after unit is plugged in

again or after a power failure, reset the clock.

General control

Input function

When the INPUT on main unit is pressed, the current function

will change to different mode. Press the INPUT repeatedly to

select desired function.

Display brightness control

Press DIMMER to dims the display brightness. The

brightness can be controlled in four steps.

Volume auto setting

If you turn off and on the main unit with the volume set to 31

or higher, the volume starts at 30.

Volume control

Turn the VOLUME on the unit or press VOLUME +/– on the

remote control to increase or decrease the volume.

CAUTION

• The sound level at a given volume setting depends on

speaker efficiency, location, and various other factors. It

is advisable to avoid exposure to high volume levels. Do

not turn the volume on to full at switch on. Listen to

music at moderate levels. Excessive sound pressure

from earphones and headphones can cause hearing

loss.

Muting

The volume is muted temporarily when pressing the MUTE on

the remote control. Press again to restore the volume.

STANDBY/ON





CD USB TUNER AUDIO IN

123

BT AUDIO

CLOCK/TIMER

SLEEP

EQUALIZER

OPEN/CLOSE

DISPLAY FOLDER

MENU

PRESET VOLUME

TUNE–

TUNE+

MEMORY

/PROGRAM

ENTER

CD AM USB/iPodFM

AUDIO IN

LINE

BT AUDIO

;+0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸲᭶㸰᪥ࠉⅆ᭙᪥ࠉ༗๓㸶᫬㸳㸲ศ

Getting started04

14

En

Sound controls

Equalizer

When the EQUALIZER is pressed, the current mode setting

will be displayed. To change to a different mode, press the

EQUALIZER repeatedly until the desired sound mode

appears.

P.BASS control

When the power is first turned on, the unit will enter the

P.BASS mode which emphasises the bass frequencies. To

cancel the P.BASS mode, press the P.BASS on the remote

control.

Bass/treble control

Press the BASS/TREBLE, then press FG/HI to adjust the

bass or treble.

Note

•The EQUALIZER and P.BASS cannot operate

simultaneously. The most recently selected of these two

functions will be the one used.

• BASS/TREBLE can operate alongside either the

EQUALIZER or P.BASS.

When one of the above two functions is

selected, the function that is not selected

will be displayed as follows.

1When

P.BASS

setting (

ON

/

OFF

) is changed

• EQUALIZER : FLAT

2When

EQUALIZER

setting is changed

• P.BASS : OFF

Setting the wake-up timer

Used to change the existing timer setting, or to set a new

timer.

1Press

1 STANDBY/ON

to turn the power on.

2 Press and hold

CLOCK/TIMER

.

3Press

HI

to select “ONCE” or “DAILY”,

then press ENTER.

ONCE – Works once only at a preset time.

DAILY – Works at the preset time on a preset day.

4Press

HI

to select “TIMER SET”, then

press ENTER.

5Press

HI

to select the timer playback

source, then press

ENTER

.

• CD, FM, AM, USB/iPod, BT AUDIO, AUDIO IN and LINE

can be selected as the playback source.

6Press

HI

to select the timer day, then

press ENTER.

7Press

HI

to set the hour, then press

ENTER.

8Press

HI

to set the minute, then press

ENTER.

• Set the time to finish as in steps 7 and 8 above.

9 Adjust the volume press

VOLUME +/–

, then

press ENTER.

10 Press

1 STANDBY/ON

to enter the power

standby mode.

•The TIMER indicator lights up.

NIGHT

FLAT A flat and basic sound.

ACTIVE

DIALOGUE

A sound that can be enjoyed

at night even with lower volume.

A powerful sound that

emphasizes low and high tones.

A sound that allows the radio or

vocals to be heard more easily.

B*HWWLQJBVWDUWHGB;+0IP࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸳᭶㸰㸶᪥ࠉⅆ᭙᪥ࠉ༗ᚋ㸰᫬㸱㸯ศ

Getting started 04

15

En

English Français Español

Calling the wake-up timer

An existing timer setting can be reused.

1 Follow steps 1 to 3 in “Setting the wake-up

timer”.

2 Press

HI

to select “TIMER ON”, then press

ENTER.

Cancelling the wake-up timer

Turn off the timer setting.

1 Follow steps 1 to 3 in “Setting the wake-up

timer”.

2 Press

HI

to select “TIMER OFF”, then

press ENTER.

Using the wake-up timer

1 Press

1 STANDBY/ON

to turn the power

off.

2 At the wake-up time, this unit will turn on

automatically and play the selected input

function.

Note

• If at the wake-up time an iPod/iPhone/iPad is not

connected to the unit or a disc is not inserted, the unit

will be turned on but will not play back the track.

• Some discs may not be played automatically at the wake-

up time.

• When setting the timer set at least one minute between

the start and end time.

Using the sleep timer

The sleep timer switches off the unit after a specified time so

you can fall asleep without worrying about it.

1 Press

SLEEP

repeatedly to select a switch off

time.

Choose between 10 min, 20 min, 30 min, 60 min, 90 min, 120

min, 150 min, 180 min or OFF. The newly set value displays for

3 seconds, and then the setting is completed.

Note

• The sleep timer can be set by pressing SLEEP while the

remaining time is displayed.

Using Headphones

Connect the headphones plug to the PHONES terminal.

When the headphones are connected, there is no sound

output from the speakers.

• Do not turn the volume on to full at switch on and listen

to music at moderate levels. Excessive sound pressure

from earphones and headphones can cause hearing

loss.

• Before plugging in or unplugging the headphone,

reduce the volume.

• Be sure your headphone has a 3.5 mm diameter plug

and impedance between 16

: and 50 :. The

recommended impedance is 32

:.

• Audio from the iPod/iPhone/iPad cannot be heard via

the headphones connected to the unit. “HP MUTE” will

be displayed if you connect the headphones when the

iPod/iPhone/iPad function is selected.

 STANDBY/ON

INPUT

VOLUME

PHONES AUDIO IN

  

TIMER

;+0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸱᭶㸰㸶᪥ࠉᮌ᭙᪥ࠉ༗ᚋ㸰᫬㸯ศ

iPod/iPhone/iPad playback05

16

En

Chapter 5:

iPod/iPhone/iPad playback

Merely by connecting your iPod/iPhone/iPad to this unit, you

can enjoy high-quality sound from your iPod/iPhone/iPad.

Playback setting for iPod/iPhone/iPad music can be

performed from this unit or the iPod/iPhone/iPad itself.

Confirming what iPod/iPhone/iPad

models are supported

The iPod/iPhone/iPad playable on this unit are shown below.

Note

• Pioneer does not guarantee that this unit plays iPod/

iPhone/iPad models other than the ones specified.

• Some functions may be restricted depending on the

model or software version.

• iPod/iPhone/iPad is licensed for reproduction of non-

copyrighted materials or materials the user is legally

permitted to reproduce.

• Features such as the equalizer cannot be controlled

using this system, and we recommend switching the

equalizer off before connecting.

• Pioneer cannot under any circumstances accept

responsibility for any direct or indirect loss arising from

any inconvenience or loss of recorded material resulting

from iPod/iPhone/iPad failure.

• For detailed instructions on using the iPod/iPhone/iPad,

please refer to the manual supplied with the iPod/

iPhone/iPad.

• This system has been developed and tested for the

software version of iPod/iPhone/iPad indicated on the

website of Pioneer (http://pioneer.jp/homeav/support/

ios/eu/).

• Installing software versions other than indicated on the

website of Pioneer to your iPod/iPhone/iPad may result

in incompatibility with this system.

• This unit cannot be used to record CD, tuner or other

content on an iPod/iPhone/iPad.

Connecting your iPod/iPhone/iPad

Connecting iPod/iPhone/iPad using

supplied iPad stand

1 Connect the iPod/iPhone/iPad cable to the

unit.

2 Pass the iPod/iPhone/iPad cable through the

bottom of the stand and connect it to the iPod/

iPhone/iPad.

3 Set the iPod/iPhone/iPad on the stand.

iPod/iPhone/iPad USB Terminal (Audio only)

iPod nano (3/4/5/6/7G) 

iPod touch (1/2/3/4/5G) 

iPhone 5 

iPhone 4S 

iPhone 4 

iPhone 3GS 

iPhone 3G 

iPhone 

iPad mini 

iPad (3/4G) 

iPad/iPad 2 

;+0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸱᭶㸰㸶᪥ࠉᮌ᭙᪥ࠉ༗ᚋ㸰᫬㸯ศ

iPod/iPhone/iPad playback 05

17

En

English Français Español

Playing iPod/iPhone/iPad

1 Connect your iPod/iPhone/iPad.

• If an iPod/iPhone/iPad is connected while the unit is

turned on, playback of the iPod/iPhone/iPad will not

begin.

2 Press

USB

as the input source.

“USB/iPod” is shown on the main display.

3 When the recognition is completed, will

begin playing automatically.

• The available iPod/iPhone/iPad playback controls from

the unit are !, + ), *,.

• In the following case, operate your iPod/iPhone/iPad

directly:

- Searching a file by artist name or genre.

- Playing in the repeat or random mode.

CAUTION

• When your iPod/iPhone/iPad is connected to this unit

and you wish to operate the iPod/iPhone/iPad directly,

be sure to steady the iPod/iPhone/iPad with the other

hand to prevent malfunctions due to faulty contacts.

Note

• For detailed instructions on using the iPod/iPhone/iPad,

please refer to the manual supplied with the iPod/

iPhone/iPad.

• iPod/iPhone/iPad recharging occurs whenever an iPod/

iPhone/iPad is connected to this unit. (This function is

supported in standby mode as well.)

• When input is switched from USB/iPod to another

function, iPod/iPhone/iPad playback is temporarily

stopped.

Important

If this unit cannot play your iPod/iPhone/iPad, perform the

following troubleshooting checks:

• Check whether the iPod/iPhone/iPad is supported by

this unit.

• Reconnect the iPod/iPhone/iPad to the unit. If this

doesn’t seem to work, try resetting your iPod/iPhone/

iPad.

• Check that iPod/iPhone/iPad software is supported by

the unit.

If the iPod/iPhone/iPad cannot be operated, check the

following items:

• Is the iPod/iPhone/iPad connected correctly? Reconnect

the iPod/iPhone/iPad to the unit.

• Is the iPod/iPhone/iPad experiencing a hangup? Try

resetting the iPod/iPhone/iPad, and reconnect it to the

unit.

;+0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸱᭶㸰㸶᪥ࠉᮌ᭙᪥ࠉ༗ᚋ㸰᫬㸯ศ

Disc playback06

18

En

Chapter 6:

Disc playback

This system can play back a standard CD, CD-R/RW in the CD

format and CD-R/RW with MP3 or WMA files, but cannot

record on them. Some audio CD-R and CD-RW discs may not

be playable due to the state of the disc or the device that was

used for recording.

MP3:

MP3 is a form of compression. It is an acronym which stands

for MPEG Audio Layer 3. MP3 is a type of audio code which is

processed by significant compression from the original audio

source with very little loss in sound quality.

• This system supports MPEG-1/2 Audio Layer 3 (Sampling

rates: 8 kHz to 48 kHz; Bit rates: 64 kbps to 384 kbps).

• During VBR file playback, time counter in the display

may differ from its actual playback time.

WMA:

WMA (Windows Media Audio) files are Advanced System

Format files that include audio files which are compressed

with Windows Media Audio codec. WMA is developed by

Microsoft as an audio format file for Windows Media Player.

• This system supports WMA (Sampling rates: 32 kHz/44.1

kHz/48 kHz; Bit rates: 64 kbps to 320 kbps).

• During VBR file playback, time counter in the display

may differ from its actual playback time.

Playing discs or files

1 Press

1 STANDBY/ON

to turn the power on.

2 Press

CD

on the remote control or

INPUT

repeatedly on the main unit to select CD input.

3 Press

$ OPEN/CLOSE

to open the disc tray.

4 Place the disc on the disc tray, label side up.

5 Press

$ OPEN/CLOSE

to close the disc tray.

6 Press

!

to start playback.

After the last track is played, the unit will stop automatically.

CAUTION

• Do not place two discs in one disc tray.

• Do not play discs of special shapes (heart, octagon, etc).

It may cause malfunctions.

• Do not push the disc tray whilst it is moving.

• If the power fails whilst the tray is open, wait until the

power is restored.

• Be sure to place 8 cm disc in the middle of the disc tray.

Note

• Due to the structure of the disc information, it takes longer

to read an MP3/WMA disc than a normal CD

(approximately 20 to 90 seconds).

• When the beginning of the first track is reached during fast

reverse, the unit will enter the playback mode (only for CD).

• Rewritable multi-session discs with unfinished writing, can

still be played.

• If TV or radio interference occurs during CD operation,

move the unit away from the TV or radio.

Tip

• When no operation has done in CD mode and the audio

file is not played for more than 30 minutes, the power will

automatically turn off.

Various disc functions

Function Main

unit

Remote

control

Operation

Play

Press in the stop mode.

Stop

Press in the playback mode.

Pause

Press in the playback mode.

Press

!

to resume

playback from the paused

point.

Track up/

down

Press in the playback or stop

mode.

If you press the button in the

stop mode, press

!

to start

the desired track.

Fast

forward/

reverse

Press and hold down in the

playback mode.

Release the button to resume

playback.































;+0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸱᭶㸰㸶᪥ࠉᮌ᭙᪥ࠉ༗ᚋ㸰᫬㸯ศ

Disc playback 06

19

En

English Français Español

Advanced CD or MP3/WMA disc

playback

Direct track search

By using the numeric buttons, the desired tracks on the

current disc can be played.

Use the numeric buttons on the remote control to

select the desired track whilst playing the selected

disc.

Note

• A track number higher than the number of tracks on the

disc cannot be selected.

To stop playback:

Press #.

Repeat play

Repeat play can play one track, all tracks or a programmed

sequence continuously.

To repeat one track:

Press REPEAT repeatedly until “REPEAT ONE” appears. Press

ENTER.

To repeat all tracks:

Press REPEAT repeatedly until “REPEAT ALL” appears. Press

ENTER.

To repeat desired tracks:

Perform steps 1 to 5 in “Programmed play (CD or MP3/WMA)”

section on next page and then press REPEAT repeatedly until

“REPEAT ALL” appears. Press ENTER.

To cancel repeat play:

Press REPEAT repeatedly until “REPEAT OFF” appears. Press

ENTER.

Note

• After performing repeat play, be sure to press #.

Otherwise, the disc will play continuously.

• During repeat play, random play is not possible.

Random play

The tracks on the disc can be played in random order

automatically.

To random play all tracks:

Press RANDOM repeatedly until “RANDOM ON” appears.

Press ENTER.

To cancel random play:

Press RANDOM repeatedly until “RANDOM OFF” appears.

Press ENTER.

Note

• If you press the , during random play, you can move

to the track selected next by the random operation. On

the other hand, the + does not allow you to move to

the previous track. The beginning of the track being

played will be located.

• In random play, the unit will select and play tracks

automatically. (You cannot select the order of the

tracks.)

• During random play, repeat play is not possible.

DISPLAY FOLDER

MENU

PRESET VOLUME

ST/MONO ASPM PTY DISPLAY

+

MUTE

TUNE–

TUNE+

DIMMER

 







–

+

–

MEMORY

/PROGRAM

0

RDS

ENTER

STANDBY/ON





CD USB TUNER AUDIO IN

DISPLAY FOLDER

TUNE+

123

456

789

0

BT AUDIO

CLOCK/TIMER

SLEEP

EQUALIZER

P. BA S S

BASS/TREBLE

RANDOM

CLEAR REPEAT

OPEN/CLOSE

;+0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸱᭶㸰㸶᪥ࠉᮌ᭙᪥ࠉ༗ᚋ㸰᫬㸯ศ

Disc playback06

20

En

Programmed play (CD or MP3/WMA)

You can choose up to 32 selections for playback in the order

you like.

1 Whilst in the stop mode, press

MEMORY

/

PROGRAM

on the remote control to enter the

programming save mode.

2 Press

+,

or the numeric buttons on the

remote control to select the desired tracks.

3 Press ENTER to save folder and track

number.

4 Repeat steps 2 to 3 for other folder/tracks.

Up to 32 tracks can be programmed.

• If you want to check the programmed tracks, press

MEMORY/PROGRAM.

• If you make a mistake, the last programmed tracks will

be canceled by pressing CLEAR.

5 Press

!

to start playback.

To cancel the programmed play mode:

To cancel the programmed play, press # twice on the remote

control. The display will show “PRG CLEAR” and all the

programmed content will be cleared.

Adding tracks to the program:

Press the MEMORY/PROGRAM. Then follow steps 2 to 3 to

add tracks.

Note

• When a disc is ejected anything programmed is cleared.

• If you press the 1 STANDBY/ON to enter the standby

mode or change the function from CD to another, the

programmed selections will be cleared.

• During the program operation, random play is not

possible.

About downloading MP3/WMA

There are many music sites on the internet that you can

download MP3/WMA music files. Follow the instructions

from the website on how to download the music files. You can

then play back these downloaded music files by burning them

to a CD-R/RW disc.

• Your downloaded song/files are for personal use only.

Any other usage of the song without owner’s permission,

is against the law.

About folder playback order

If MP3/WMA files are recorded in several folders, a folder

number will be set to each folder automatically.

These folders can be selected by the FOLDER on the remote

control. If there is no supported file formats inside the

selected folder, the folder is skipped and the next folder will be

selected.

Example: How the folder numbers are assigned if MP3/WMA

format files are recorded are as shown below.

1 ROOT folder is set as FOLDER 1.

2 As for folders inside ROOT folder (FOLDER A

and FOLDER B), the folder which is recorded

earlier on the disc will be set as FOLDER 2 and

FOLDER 3.

3 As for folder inside FOLDER A (FOLDER C and

FOLDER D), the folder which is recorded earlier

on the disc will be set as FOLDER 4 and FOLDER

5.

4 FOLDER E that is inside FOLDER D will be set

as FOLDER 6.

• The folder and file order information which is recorded

on the disc depends on the writing software. There

maybe possibilities that this unit will playback the files

not according to our expected playback order.

• From a disc with MP3/WMA files up to 255 folders and

999 files (including non playable files) can be read.

ROOT

(FOLDER 1)

FOLDER A

(FOLDER 2)

FOLDER B

(FOLDER 3)

FILE 9

FILE 10

FILE 3

FILE 4

FILE 5

FILE 6

FILE 7

FILE 8

FOLDER E

(FOLDER 6)

FOLDER C

(FOLDER 4)

FOLDER D

(FOLDER 5)

FILE 1

FILE 2

;+0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸱᭶㸰㸶᪥ࠉᮌ᭙᪥ࠉ༗ᚋ㸰᫬㸯ศ

La pagina sta caricando ...

Pioneer X-HM51 Manuale utente

Pioneer X-HM51 Manuale utente

in altre lingue

Documenti correlati

Altri documenti