Worx WG349E Manuale utente

WG349E WG349E.9 WA0307

20V Cordless Pole Saw

20V Akku-Pole-Kettensäge

Scie à colonne sans fil 20V

20 V Sega Potatrice a batteria

20V Motosierra inalámbrica

Serra de pólo sem fio 20V

20V Draadloze kettingzaag

20V Trådløs motorsav

20V Trådløs motorsag

20V Sladdlös motorsåg

20 V Akumulatorowa piła łańcuchowa

μ  μ  20V

20 V Vezeték nélküli láncfűrész

20V Fierăstrău cu poli fără fir

20 V Akumulátorová řetězová pila

20 V Akumulátorová reťazová píla

20V Brezžična motorna žaga

P10

P19

P30

P41

P52

P63

P74

P85

P94

P104

P114

P125

P137

P148

P158

P168

P178

EN

D

F

I

ES

PT

NL

DK

NOR

SV

PL

GR

HU

RO

CZ

SK

SL

Original Instruction

Originalbetriebsanleitung

Notice originale

Istruzioni originali

Manual original

Oorspronkelijke gebruiksaanwijzing

Original brugsanvisning

Original driftsinstruks

Bruksanvisning i original

Instrukcja oryginalna

 Ω ΩΩ ΔΩ

Eredeti használati utasítás

Instrucţiuni originale

Původní návod k používání

Pôvodný návod na použitie

Izvirna navodila

EN

D

F

I

ES

PT

NL

DK

NOR

SV

PL

GR

HU

RO

CZ

SK

SL

13

6

20 19 18 1721

810

14

26

15

12

11

7

16

45

23 24

25

22

2

9

13

Kink

1

2

11

12

13

27

D

C2

C1

B2

B1

A

Bar

0.12-0.2”

2

1

3

1

2

3

2

1

G

F1

E

F2

H2

H1

1

2

1

2

1

2

L1

K

J

I2

I1

L2

1

2

8

N2

N1

M

O1

O3

O2

2" to 4"

(5 a 10 cm)

6"

(15 cm)

W

Y

ZX

Y

1/3

a

Q

P

O6

O5

O4

10

20V Cordless Pole Saw

EN

PRODUCT SAFETY

ORIGINAL INSTRUCTIONS

GENERAL POWER TOOL

SAFETY WARNINGS

WARNING: Read all safety warnings and all

instructions.

Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and instructions for future

reference.

The term “power tool” in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or

dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust.

Power tools

create sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while

operating a power tool.

Distractions can cause you

to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet. Never

modify the plug in any way.

Do not use any

adapter plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce

risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators.

There is an increased risk of electric

shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions.

Water entering a power tool will increase

the risk of electric shock.

d) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk

of electric shock.

e) When operating a power tool outdoors, use an

extension cord suitable for outdoor use.

Use of

a cord suitable for outdoor use reduces the risk of

electric shock.

f) If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply.

Use of an RCD reduces the risk of

electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do

not use a power tool while you are tired or under the

influence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result

in serious personal injury.

b) Use personal protective equipment. Always

wear eye protection.

Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions

will reduce personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the off-position before connecting

to power source and/or battery pack, picking up

or carrying the tool.

Carrying power tools with your

finger on the switch or energising power tools that

have the switch on invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on.

A wrench or a key left

attached to a rotating part of the power tool may

result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times.

This enables better control of

the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery.

Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long

hair can be caught in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used.

Use of

dust collection can reduce dust-related hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application.

The correct power

tool will do the job better and safer at the rate for

which it was designed.

b) Do not use the power tool if the switch does not

turn it on and off.

Any power tool that cannot be

controlled with the switch is dangerous and must be

repaired.

c) Disconnect the plug from the power source and/

or the battery pack from the power tool before

making any adjustments, changing accessories,

or storing power tools.

Such preventive safety

measures reduce the risk of starting the power tool

accidentally

.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are dangerous

in the hands of untrained users.

e) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and

any other condition that may affect the power

tool’s operation.

If damaged, have the power tool

repaired before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean.

Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking

into account the working conditions and the

work to be performed.

Use of the power tool for

operations different from those intended could result

in a hazardous situation.

11

20V Cordless Pole Saw

EN

5) Battery tool use and care

a) Recharge only with the charger specified by the

manufacturer.

A charger that is suitable for one

type of battery pack may create a risk of fire when

used with another battery pack.

b) Use power tools only with specifically

designated battery packs.

Use of any other battery

packs may create a risk of injury and fire.

c) When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects,

that can make a connection from one terminal

to another.

Shorting the battery terminals together

may cause burns or a fire.

d) Under abusive conditions, liquid may be ejected

from the battery; avoid contact.

If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation or

burns.

6) Service

a) Have your power tool serviced by a qualified

repair person using only identical replacement

parts.

This will ensure that the safety of the power

tool is maintained.

POLE SAW SAFETY WARNINGS

1. Keep the pole saw a sufficient distance away from

overhead electrical power lines.

2. Be aware of the dangerous of operating positions, as

well as the risk of being struck by falling branches or

branches that, having hit the ground, rebound, the

operator may be struck by falling branches or by those

that rebound after hitting the ground. Remove the

branches in sections.

SAFETY WARNINGS FOR

BATTERY PACK

a) Do not dismantle, open or shred cells or battery

pack.

b) Do not short-circuit a battery pack. Do not store

battery packs haphazardly in a box or drawer

where they may short-circuit each other or be

short-circuited by conductive materials. When

battery pack is not in use, keep it away from other

metal objects, like paper clips, coins, keys, nails,

screws or other small metal objects, that can make

a connection from one terminal to another. Shorting

the battery terminals together may cause burns or a

fire.

c) Do not expose battery pack to heat or fire. Avoid

storage in direct sunlight.

d) Do not subject battery pack to mechanical

shock.

e) In the event of battery leaking, do not allow the

liquid to come into contact with the skin or eyes.

If contact has been made, wash the affected

area with copious amounts of water and seek

medical advice.

f) Keep battery pack clean and dry.

g) Wipe the battery pack terminals with a clean dry

cloth if they become dirty.

h) Battery pack needs to be charged before use.

Always refer to this instruction and use the

correct charging procedure.

i) Do not maintain battery pack on charge when

not in use.

j) After extended periods of storage, it may

be necessary to charge and discharge the

battery pack several times to obtain maximum

performance.

k) Recharge only with the charger specified

by Worx. Do not use any charger other than

that specifically provided for use with the

equipment.

l) Do not use any battery pack which is not

designed for use with the equipment.

m) Keep battery pack out of the reach of children.

n) Retain the original product literature for future

reference.

o) Remove the battery from the equipment when

not in use.

p) Dispose of properly.

q) Do not mix cells of different manufacture,

capacity, size or type within a device.

r) Keep the battery away from microwaves and

high pressure.

SAVE THESE INSTRUCTIONS

SYMBOLS

To reduce the risk of injury, user must

read instruction manual

Warning

Wear ear protection

Wear eye protection

Wear head protection

Wear protective gloves

12

20V Cordless Pole Saw

EN

Wear protective footwear

Do not expose to moisture.

Keep sufficient distance away from

electrical power lines

Waste electrical products must not

be disposed of with household waste.

Please recycle where facilities exist.

Check with your local authorities or

retailer for recycling advice.

Li-Ion battery This product has been

marked with a symbol relating to

‘separate collection’ for all battery

packs and battery pack. It will then

be recycled or dismantled in order to

reduce the impact on the environment.

Battery packs can be hazardous for the

environment and for human health since

they contain hazardous substances.

Do not burn

Batteries may enter water cycle if

disposed improperly, which can be

hazardous for ecosystem. Do not dispose

of waste batteries as unsorted municipal

waste.

Unlock

Lock

COMPONENT LIST

1. CHAIN

2. CHAIN TENSIONING KNOB

3. CHAIN COVER

4. SAW HEAD ADJUSTMENT KNOB

5. SAW HEAD LOCKINGBUTTONS

6. OIL FILLER CAP

7. GUIDE BAR

8. OIL LEVEL WINDOW

9. DRIVE SPROCKET

10. CHAIN DIRECTION SYMBOL

11. BAR LOCATING TABS

12. FASTENING BAR BOLT

13. BAR PAD

14. BUMPER SPIKE

15. OIL OUTLET

16. BAR AND CHAIN SHEATH

17. POLE SAW ASSEMBLY LEVER

18. INNER POLE CLAMPING LEVER

19. ONOFF TRIGGER

20. BATTERY PACK

21. BATTERY PACK RELEASE BUTTON

22. REAR HANDLE

23. EXTENSION POLE LOCKOFF BUTTON

24. EXTENSION POLE ROTATION BUTTON

25. SHOULDER STRAP HOOKS

26. SHOULDER STRAP

27. BAR TENSIONING PLATE SEE FIG. A

 Not all the accessories illustrated or described

are included in standard delivery.

13

20V Cordless Pole Saw

EN

TECHNICAL DATA

Type WG349E WG349E.9 (3 - designation of machin-

ery, representative of pole saw)

WG349E WG349E.9

Voltage 20 V Max. **

Bar length 20 cm

Cutting length 18 cm

Chain speed 5.0 m/s

Oil tank capacity 80 ml

Chain pitch 0.95 cm(3/8”)

Number of chain

drive links 33

Chain gauge 1.1 mm(0.043”)

Adaptive Chain type Trilink Huihuang: CL14333X

Jinfeng Garden Tools: 90X-33

Adaptive Bar type

Trilink Huihuang: N1430833-

1041TL

Jinfeng Garden Tools:

ES084SDEA041(A)

Charging time 1 hr /

Weight (chain & bar

included) 3.7 kg 3.3 kg

Total reach 3.6 m

Machine length from 1.8 m to 2.3 m (fully

extended)

Saw head rotation

angle 00, 150, 300 (3 positions)

Handle rotation

angle 180 degrees total

** Voltage measured without workload. Initial battery

voltage reaches maximum of 20 volts. Nominal voltage is

18 volts.

ACCESSORIES

WG349E WG349E.9

Charger (WA3880) 1 /

Battery pack

(WA3551) 1/

Shoulder strap 1 1

Bar & Chain Sheath 1 1

Pole saw head attach-

ment (WA0307)

11

We recommend that you purchase your accessories listed

in the above list from the same store that sold you the tool.

Refer to the accessory packaging for further details. Store

personnel can assist you and offer advice.

NOISE DATA

A weighted sound pressure L

pA

= 79.07 dB(A)

K

PA

= 3 dB(A)

A weighted sound power L

wA

= 89.7 dB(A)

K

PA

= 3 dB(A)

Wear ear protection.

VIBRATION INFORMATION

Vibration total values (triax vector sum) determined ac-

cording to EN ISO 11680-1.

Vibration emission value: ah

= 1.83 m/s2 Uncertainty K = 1.5 m/s

The declared vibration total value may be used for

comparing one tool with another, and may also be used in a

preliminary assessment of exposure.

WARNING: The vibration emission value during

actual use of the power tool can differ from the

declared value depending on the ways in which the tool

is used dependant on the following examples and other

variations on how the tool is used:

How the tool is used and the materials being cut or drilled.

The tool being in good condition and well maintained

Using the correct accessory for the tool and ensuring it is

sharp and in good condition.

The tightness of the grip on the handles and if any anti

vibration accessories are used.

And the tool is being used as intended by its design and

these instructions.

This tool may cause hand-arm vibration syndrome if

its use is not adequately managed.

WARNING: To be accurate, an estimation of exposure

level in the actual conditions of use should also take

account of all parts of the operating cycle such as the times

when the tool is switched off and when it is running idle but

not actually doing the job. This may significantly reduce the

exposure level over the total working period.

Helping to minimise your vibration exposure risk.

ALWAYS use sharp chisels, drills and blades.

Maintain this tool in accordance with these instructions and

14

20V Cordless Pole Saw

EN

keep well lubricated (where appropriate).

If the tool is to be used regularly then invest in anti vibration

accessories.

Plan your work schedule to spread any high vibration tool

use across a number of days.

INTENDED USE

The pole saw is intended for sawing of trees, tree trunks,

branches, wooden beams, planks, etc. Cuts can be sawed

with or across the grain. This product is not suitable for

sawing mineral materials.

ASSEMBLY

WARNING! Do not install the battery pack

before it has been completely assembled.

Always use gloves when handling the chain.

CHAIN AND GUIDE BAR ASSEMBLY

1. Unpack all parts carefully.

2. Place the saw on a solid, level surface.

3. Use only genuine Worx chains or those recommended

for Guide Bar.

4. Slide the Chain (1) in the slot around the Guide Bar

(7). Ensure the Chain is in correct running direction

by comparing it to the chain icon on the guide bar, or

referring to the Chain Direction Symbol (10) found on

the saw body. Ensure the Bar Tensioning Plate (27) is

facing outward. (See Fig. A)

5. Fit the Chain onto the Drive Sprocket (9), so that the

Fastening Bar Bolt (12) and the two Bar Locating Tabs

(11) on the Bar Pad (13) fit into the keyway of the opening

on the Guide Bar (7). (See Fig. B1, B2)

6. Assure all parts are seated properly. Make sure the drive

links are fully seated in the drive sprocket (See Fig. C1),

avoiding a kink as shown in Fig. C2. If kink occurs, pick

up on the chain at the guide bar just ahead of the kink

and then pull the kink out.

NOTE: Chain should rotate freely and be free of kinks.

7. Fit the Chain Cover (3) and tighten the Chain Cover by

turning the Chain Tensioning Knob (2) clockwise until it

is tight. (See Fig. D)

WARNING The chain is not yet tensioned.

Tensioning the chain applies as described

under “TENSIONING CHAIN”. The chain now

needs to be inspected to make sure it is properly

tensioned.

TENSIONING CHAIN (See Fig. E)

NOTE: New saw chains will stretch. Check the chain tension

frequently when first used and tighten when the Chain (1)

becomes loose around the Guide Bar (7).

WARNING:

 Removing the battery pack before adjusting saw

chain tension.

 Cutting edges on chain are sharp. Use protective

gloves when handling chain.

 Maintain proper chain tension always. A loose

chain will increase the risk of kickback. A loose

chain may jump out of guide bar groove. This may

injure operator and damage chain. A loose chain

will cause chain, bar, and sprocket to wear rapidly.

1. Place the saw on any suitable flat surface.

2. Turn the Chain Tensioning Knob (2) clockwise until it is

hand tight.

NOTE: The tension is automatically increased while the

Chain Tensioning Knob (2) is being turned in a clockwise

direction. The built-in ratchet mechanism prevents the

chain tension from loosening.

3. Double check the tension set by the automatic Chain

Tensioning Knob. The correct chain tension is reached

when the Chain (1) can be raised approx. half the

drivelink depth from the Guide Bar (7) in the center. This

should be done by using one hand to raise the chain

against the weight of the machine. (See Fig. E)

NOTE: The Chain (1) is properly tensioned when it can be

lifted off of the Guide Bar (7) and the drivelink is within

the rail of the Guide Bar (7).

NOTE: The Chain (1) will stretch while cutting and

lose proper tension. When the chain becomes loose,

completely unscrew the Chain Tensioning Knob (2)

or turn the knob around three full turns in a counter-

clockwise direction, then retighten the Chain Tensioning

Knob (2) to properly reset the chain tension by

repeating Steps 1-4 listed above.

ASSEMBLING THE EXTENSION POLE TO THE MACHINE

(See Fig. F1)

Step 1: Loosen the pole saw assembly lever (17) as shown in

Fig F1. Align and insert the machine into the extension pole.

Step 2: Press the pole saw assembly lever to tighten the

extension pole to the machine.

NOTE: Make sure the extension pole is locked into

position securely before operation.

REMOVING THE EXTENSION POLE (See Fig. F2)

Step 1: Unlock the pole saw assembly lever (17) as shown.

Step 2: Slide saw to disconnect the extension pole with

the saw while pressing both saw head locking-buttons (5)

simultaneously.

ADJUSTING POLE LENGTH (See Fig. G)

The pole saw has a telescoping pole assembly that will

extend from 1.8m(fully retracted) to 2.3m (fully extended) .

Inner pole clamping level (18) is used to hold the pole in

position at any extended length.

1. To extend the pole, loosen the inner pole clamping lever

(18) as shown in Fig. G. Pole will slide freely.

2. Pull inner pole section out to desired length of

extension.

NOTE: only extend pole to minimum length required to

reach limb that is being cut.

3. To lock pole in position, tighten clamping lever as shown

in Fig. G.

ATTACHING AND ADJUSTING THE SHOULDER STRAP

(See Fig. H1, H2)

Attach the shoulder strap to the hooks on the pole with the

included carabiner hook, as shown in Fig. H1. To adjust the

position of the shoulder strap, loosen the Locking knob by

turning it counter-clockwise. Move it to the desired position.

Tighten the Locking Knob clockwise to lock, as indicated.

15

20V Cordless Pole Saw

EN

ADJUSTING THE SAW HEAD ANGLE (See Fig. I1, I2)

The saw head can be rotated for different cutting angles for

0

o

, 15

o

, and 30

o

. (See Fig. I1)

1. Rotate the pole saw head to the desired cutting angle

while pressing the Saw Head Adjustment Knobs located

on both sides simultaneously. (See Fig. I2)

2. Release the knobs when the pole saw head is set to the

desired angle.

NOTE: Failure to properly secure the pole saw head may

result in personal injury and/or property damage.

WARNING! Always ensure the pole saw head is

securely locked! Do not attempt to use the pole

saw with the head in any other position or

unlocked!

ADJUSTING THE REAR HANDLE (See Fig. J)

Push the extension pole rotation button forward to unlock.

Hold the rear handle and rotate it to the most comfortable

and balanced position. Release the extension pole rotation

button to lock the rear handle.

WARNING: Always make sure that the handle is

locked in the desired position before operation.

Do not rotate the handle when the saw is being

operated.

LUBRICATION

Important: The pole saw is not filled with oil. It

is essential to fill with oil before use. Never

operate the pole saw without chain oil or at an

empty oil tank level, as this will result in extensive

damage to the product.

NOTE: Chain life and cutting capacity depend

on optimum lubrication. Therefore, the chain is

automatically oiled during operation.

FILLING OIL TANK SEE FIG. K

WARNING: Removing the battery pack before

filling the oil tank.

1. Set pole saw on any suitable surface with Oil Filler Cap

(6) facing upward.

2. Clean area around the Oil Filler Cap with cloth and

unscrew the cap by turning it counter clockwise.

3. Add bar and chain oil (not included) until tank is full.

4. Avoid dirt or debris entering oil tank, refit Oil Filler Cap

(6) and tighten by turning clockwise until hand tight.

Important: To allow venting of the oil tank,

small breather channels are provided between

the Oil Filler Cap and the strainer, to prevent

leakage, and ensure machine is left in a horizontal

position (Oil Filler Cap (6) uppermost) when not in

use.

It is important to use bar and chain lubricant (not

provided) that is formulated to perform over a wide

temperature range with no dilution required. This can

be found at the location where you purchased this

saw or your local hardware store. Do not use dirty,

used or otherwise contaminated oils. Damage may

occur to the bar or chain. Use of non approved oil will

void the warranty.

Do not swallow. If swallowed, call a physician

immediately. Keep out of reach of children. Store

away from heat or open flame.

Checking the Automatic Oiler

Proper functioning of the automatic oiler can be checked by

running the pole saw and pointing the tip of the Guide Bar

(7) towards a piece of cardboard or paper on the ground.

If an increasing oil pattern develops on the cardboard, the

automatic oiler is operating fine. If there is no oil pattern,

despite a full oil reservoir, contact Worx customer service

agent or Worx approved service agent.

CAUTION: Do not touch the ground with the

chain. Ensure safety clearance of 3.6m

OPERATION

1. BEFORE USING YOUR CORDLESS TOOL

WARNING! The charger and battery pack are

specially designed to work together so do not

attempt to use any other devices. Never insert or

allow metallic objects into your charger or battery pack

connections because of an electrical failure and hazard will

occur.

NOTE: Your battery pack is UNCHARGED and you must

charge once before use.

The battery charger supplied is matched to the Li-ion

battery installed in the machine. Do not use another battery

charger.

2. CHARGING YOUR BATTERY PACK

The Li-ion battery is protected against deep discharging.

When the battery is empty, the machine is switched off by

means of a protective circuit.

In a warm environment or after heavy use, the battery pack

may become too hot to permit charging. Allow time for the

battery to cool down before recharging.

3. TO REMOVE OR INSTALL BATTERY PACK (See Fig. L1,

L2)

Depress the Battery Pack Release Button to remove the

Battery Pack from your tool. After recharging, insert the

Battery Pack into the battery port. A simple push and slight

pressure will be sufficient until a click is heard. Check to see

if the battery is fully secured.

NOTE: When removing the battery pack, hold it firmly

to avoid dropping and injury.

4. SWITCHING ON AND OFF (See Fig. M)

ATTENTION: Check the battery pack before

using your cordless tool. Only use the battery

pack listed in the accessories section.

For switching on the tool, press the extension pole lock-off

button (23), then fully press the On/Off Trigger (19) and hold

in this position. The extension pole lock-off button can now

be released.

For switching off, release the On/Off Trigger.

5. CUTTING

Important: Is the oil tank filled? Check the Oil

Level Window (8) prior to starting and

16

20V Cordless Pole Saw

EN

regularly during operation (See Fig. N1). Refill oil

when oil level is low. A full oil tank will last approx. 35

minutes of cutting depending on sawing intensity and

stops.

Check recent replaced chain tension about every 10

minutes during operation.

(1) Installing the battery pack into the machine.

(2) Make sure section of log to be cut is not laying on the

ground. This will keep the chain (1) from touching the

ground as it cuts through the log.

Touching the ground while the Chain is moving is

dangerous and will dull the Chain.

(3) Use both hands to grip saw. Always use left hand to grip

main handle and right hand to grip Rear Handle (22).

Use a firm grip. Thumbs and fingers must wrap around

saw handles. (See Fig. N2)

(4) Make sure your footing is firm. Keep feet-shoulder

width apart. Distribute your weight evenly on both feet.

(5) When ready to make a cut, push the extension pole

lock-off button (23) completely in with the right thumb

and squeeze the trigger. This will turn saw on. Releasing

the trigger will turn the saw off. Make sure the saw is

running at full speed before starting a cut.

(6) When starting a cut, slowly place moving chain against

the wood. The wood should be as close to the saw body

as possible. Hold saw firmly in place to avoid possible

bouncing or skating (sideways movement) of saw.

(7) Guide the saw using light pressure and do not put

excessive force on the saw, letting the saw do its work.

The motor will overload and can burn out. It will do

the job better and safer at the rate for which it was

intended.

(8) Remove the saw from a cut with the saw running at full

speed. Stop the saw by releasing the On/off Trigger (19).

Make sure the chain has stopped before setting the saw

down.

(9) Keep practicing on scrap logs in a secure working area

until you are comfortable, using a fluid motion and a

steady cutting rate.

Kickback Safety Devices on This Saw

This saw has a low-kickback chain and reduced kickback

Guide Bar. Both items reduce the chance of kickback.

However, kickback can still occur with this saw.

The following steps will reduce the risk of kickback.

• Use both hands to grip saw while saw is running. Use

firm grip. Thumbs and fingers must wrap around saw

handles.

• Keep all safety items in place on saw. Make sure they

work properly.

• Keep solid footing and balance at all times.

• Stand slightly to the left side of saw. This keeps your

body from being in direct line with chain.

• Do not let Guide Bar nose touch anything when chain is

moving.

• Never try cutting through two logs at same time. Only

cut one log at a time.

• Do not bury the Guide Bar nose or try plunge cut (boring

into wood using Guide Bar nose.

• Watch for shifting of wood or other forces that may

pinch chain.

• Use extreme caution when re-entering a previous cut.

• Use only the low-kickback chain and Guide Bar (7) that

were supplied with this pole saw or recommended.

• Never use a dull or loose chain. Keep chain sharp with

proper tension.

OPERATION FOR POLE SAW

Cutting with shoulder strap (See Fig. N2)

The extension pole is supplied with a shoulder strap that

gives extra support when hoisting the pole saw in the air.

Hook the shoulder strap to the extension pole and wrap

around your shoulder. The shoulder strap can also soften

the impact if the pole saw is dropped after the completion

of a cut.

Cutting with extension pole

1. Install the battery pack into the machine.

2. Before cutting a high branch, consider all the same

points detailed in the previous section “Trimming

Branches” but pay particular attention to the likely

path of the falling branch.

WARNING: Do not stand directly below a

branch being cut. Keep bystanders far away.

Do not stand on a ladder or other type of unstable

support while using the tool. Do not use the tool near

cable, electrical power or telephone lines. Keep 3m

away from all power lines. (See Fig. O1-O4)

3. Use both hands to grip Pole Saw. Use only designated

grip areas when operating Pole Saw (See Fig. O5). Use

firm grip. Thumbs and fingers must wrap around Pole

Saw handle and pole.

4. Make sure your footing is firm. Keep feet apart. Divide

your weight evenly on both feet.

5. When ready to make a cut, press the extension pole

lock-off button (23), then fully press the On/off Trigger

(19) (See Fig. M). This will turn Pole Saw on. Releasing

On/off Trigger will turn Pole Saw off. Make sure saw is

running at full speed before starting a cut.

6. When starting a cut, place moving chain against

wood. Hold Pole Saw firmly in place to avoid possible

bouncing or skating (sideways movement) of saw.

7. Guide Pole Saw using light pressure. Do not force Pole

Saw. The motor will overload and can burn out. It will

do the job better and safer at the rate for which it was

intended.

8. Remove Pole Saw from a cut with saw running at full

speed. Stop Pole Saw by releasing trigger. Make sure

chain has stopped before setting Pole Saw down.

TRIMMING A TREE (PRUNING)

WARNING: Avoid kickback. Kickback can result in

severe injury or death.

See Kickback, to avoid risk of kickback.

WARNING: Do not operate Pole Saw while

• in a tree

• on a ladder or any other unstable surface

• in any awkward position

You may lose control of Pole Saw causing severe

injury.

WARNING: Do not extend arms above shoulders when

using Pole Saw.

CAUTION: Seek professional help if facing conditions

beyond your ability.

17

20V Cordless Pole Saw

EN

Trimming a tree is the process of cutting limbs from a living

tree. Make sure your footing is firm. Keep feet apart. Divide

your weight evenly on both feet.

Follow directions below to trim a tree.

1. Make first cut six inches from tree trunk on underside

of limb. Use top of guide bar to make this cut. Cut 1/3

through diameter of limb (See Fig. O6).

2. Move two to four inches farther out on limb. Make

second cut from above limb. Continue cut until you cut

limb off.

3. Make third cut as close to tree trunk as possible on

underside of limb stub. Use top of guide bar to make

this cut. Cut 1/3 through diameter of stub.

4. Make fourth cut directly above third cut. Cut down to

meet third cut. This will remove limb stub.

SAW MAINTENANCE

Follow maintenance instructions in this manual. Proper

cleaning of saw and chain and Guide Bar maintenance can

reduce chances of kickback. Inspect and maintain saw after

each use. This will increase the service life of your saw.

NOTE: Even with proper sharpening, risk of kickback can

increase with each sharpening.

MAINTENANCE AND STORAGE

OF POLE SAW

1. Remove the battery pack

• When not in use

• Before moving from one place to another

• Before servicing

• Before changing accessories or attachments, such as

saw chain and guard

2. Inspect pole saw before and after each use. Check

saw closely if guard or other part has been damaged.

Check for any damage that may affect operator safety

or operation of saw. Check for alignment or binding of

moving parts. Check for broken or damaged parts. Do

not use pole saw if damage affects safety or operation.

Have damage repaired by authorized service center.

To locate an authorized service center, visit www.worx.

com.

3. Maintain pole saw with care.

• Never expose saw to rain or direct moisture.

• Keep chain sharp, clean, and lubricated for better and

safer performance.

• Follow steps outlined in this manual to sharpen chain.

• Keep handles dry, clean, and free of oil and grease.

• Keep all screws and nuts tight.

4. When servicing, use only identical replacement parts.

5. When not in use, always store pole saw

• in a high or locked place, out of children’s reach

• in a dry place

• with bar and chain cover (3) in place

Bar Maintenance

To maximize bar life, the following bar maintenance is

recommended.

The bar rails that carry the chain should be cleaned before

storing the tool or if the bar or chain appear to be dirty.

The rails should be cleaned every time the chain is

removed.

To clean the Bar rails.

1. Remove chain cover and bar and chain. (see section

ASSEMBLY)

2. Using a wire brush, screwdriver or similar tool, clear the

residue from the inner groove of the bar. (See Fig. P)

3. Make sure to clean oil passages thoroughly.

Conditions which require Chain (1) and Guide Bar (7)

maintenance:

• Saw cuts to one side or at an angle.

• Saw has to be forced through the cut.

• Inadequate supply of oil to the bar and chain.

Check the condition of the Guide Bar each time the chain

is sharpened. A worn Guide Bar will damage the chain and

make cutting difficult.

After each use, remove the battery pack, clean all sawdust

from the Guide Bar and sprocket hole.

When rail top is uneven, use a flat file to restore square

edges and sides.

File Rail Edges

and Sides

Square

Worn Groove Correct Groove

Replace the Guide Bar when the groove is worn, the Guide

Bar is bent or cracked, or when excess heating or burring of

the rails occurs. If replacement is necessary, use only the

Guide Bar specified for your saw in the repair parts list or on

the decal located on the pole saw.

Replacing Bar & Chain

Replace chain when cutters are too worn to sharpen or

when chain stops. Only use replacement chain noted in this

manual.

Inspect Guide Bar before sharpening chain. A worn or

damaged Guide Bar is unsafe. A worn or damaged Guide Bar

will damage chain. It will also make cutting harder.

Fit the Bar Tensioning Plate (27) Tab into the new bar by

tightening the screw clockwise. The tab protrusion (a) must

be fitted into the bar hole. (See Fig. Q)

SHARPENING SAW CHAIN

WARNING:

Remove the battery pack before servicing.

Severe injury or death could occur from

electrical shock or body contact with moving chain.

Cutting edges on chain are sharp. Use protective

gloves when handling chain.

Keep chain sharp. Your saw will cut faster and more safely. A

dull chain will cause undue sprocket, Guide Bar, chain, and

motor wear. If you must force chain into wood and cutting

creates only sawdust with few large chips, chain is dull.

ENVIRONMENTAL

PROTECTION

Waste electrical products must not be disposed

of with household waste. Please recycle where

facilities exist. Check with your local authorities or

retailer for recycling advice.

18

20V Cordless Pole Saw

EN

TROUBLESHOOTING TABLE

The following table gives checks and actions that you can perform if your machine does not operate correctly. If these do not

identify/remedy the problem, contact your service agent.

WARNING: Switch off and remove the battery pack before investigating fault.

Symptom Possible Cause Remedy

Pole saw fails to

operate Out of battery.

Fuse faulty. Charge the battery pack.

Replace fuse.

Pole saw

operates

intermittently

Over heating

Applying too much pressure while cutting.

Loose connection.

Internal wiring defective.

On/Off Trigger defective.

Place the machine in a cool, ventilated

place to cool it down

Applying relatively less pressure while

cutting

Contact service agent 1-866-354-Worx

(9679).

Dry chain No oil in reservoir

Vent in oil filler cap clogged

Oil passage clogged

Refill oil

Clean cap

Clean oil passage outlet

Chain/chain bar

over-heats

No oil in reservoir

Vent in oil filler cap clogged

Oil passage clogged

Chain is over tensioned

Dull chain

Refill oil

Clean cap

Clean oil passage outlet

Adjust chain tension

Sharpen chain or replace

Pole saw rips,

vibrates, does not

saw properly

Chain tension too loose

Dull chain

Chain worn out

Chain teeth are facing in the wrong direc-

tion

Adjust chain tension

Sharpen chain or replace

Replace chain

Reassemble with chain in correct

direction

DECLARATION OF

CONFORMITY

We,

Positec Germany GmbH

Grüner Weg 10, 50825 Cologne, Germany

Declare that the product

Description Battery-powered pole saw

Type WG349E WG349E.9 (3 - designation of machinery,

representative of pole saw)

Function Cutting high branch

Complies with the following Directives:

2006/42/EC, 2014/30/EU,

2011/65/EU&(EU)2015/863,

2000/14/EC amended by 2005/88/EC

The notified body involved

Name: Intertek Deutschland GmbH (Notified body

0905)

Address: Stangenstraße 1, 70771 LEINFELDEN-

ECHTERDINGEN

Certification No.: 190601913SHA-V1

2000/14/EC amended by 2005/88/EC:

- Conformity Assessment Procedure as per Annex V

- Measured Sound Power Level 89.7 dB(A)

- Declared Guaranteed Sound Power Level 93 dB(A)

Standards conform to

EN 60745-1, EN ISO 11680-1, EN ISO 3744,

EN 55014-1, EN 55014-2

The person authorized to compile the technical file,

Name: Marcel Filz

Address: Positec Germany GmbH, Grüner Weg 10,

50825 Cologne, Germany

2021/04/12

Allen Ding

Deputy Chief Engineer, Testing & Certification

Positec Technology (China) Co., Ltd.

18, Dongwang Road, Suzhou Industrial

Park, Jiangsu 215123, P. R. China

19

20V Akku-Pole-Kettensäge D

ORIGINALBETRIEBSANLEITUNG

PRODUKTSICHERHEIT

ALLGEMEINE

SICHERHEITSHINWEISE FÜR

ELEKTROWERKZEUGE

WARNUNG: Lesen Sie alle

Sicherheitshinweise und Anweisungen.

Versäumnisse bei der Einhaltung der Sicherheitshinweise

und Anweisungen können elektrischen Schlag, Brand und/

oder schwere Verletzungen verursachen.

Bewahren Sie alle Sicherheitshinweise und

Anweisungen für die Zukunft auf.

Der in den Sicherheitshinweisen verwendete Begriff

„Elektrowerkzeug“ bezieht sich auf akkubetriebene

Elektrowerkzeuge (ohne Netzkabel) .

1) Arbeitsplatzsicherheit

a) Halten Sie Ihren Arbeitsbereich sauber und

gut beleuchtet. Unordnung oder unbeleuchtete

Arbeitsbereiche können zu Unfällen führen.

b) Arbeiten Sie mit dem Elektrowerkzeug nicht in

explosionsgefährdeter Umgebung, in der sich

brennbare Flüssigkeiten, Gase oder Stäube

befinden. Elektrowerkzeuge erzeugen Funken, die

den Staub oder die Dämpfe entzünden können.

c) Halten Sie Kinder und andere Personen während

der Benutzung des Elektrowerkzeugs fern. Bei

Ablenkung können Sie die Kontrolle über das Gerät

verlieren.

2) Elektrische Sicherheit

a) Der Anschlussstecker des Elektrowerkzeuges

muss in die Steckdose passen. Der Stecker darf

in keiner Weise verändert werden. Verwenden

Sie keine Adapterstecker gemeinsam mit

schutzgeerdeten Elektrowerkzeugen.

Unveränderte Stecker und passende Steckdosen

verringern das Risiko eines elektrischen Schlages.

b) Vermeiden Sie Körperkontakt mit geerdeten

Oberflächen wie von Rohren, Heizungen, Herden

und Kühlschränken. Es besteht ein erhöhtes Risiko

durch elektrischen Schlag, wenn Ihr Körper geerdet

ist.

c) Halten Sie Elektrowerkzeuge von Regen oder

Nässe fern. Das Eindringen von Wasser in ein

Elektrowerkzeug erhöht das Risiko eines elektrischen

Schlages.

d) Zweckentfremden Sie das Kabel nicht, um das

Elektrowerkzeug zu tragen, aufzuhängen oder

um den Stecker aus der Steckdose zu ziehen.

Halten Sie das Kabel fern von Hitze, Öl, scharfen

Kanten oder sich bewegenden Geräteteilen.

Beschädigte oder verwickelte Kabel erhöhen das

Risiko eines elektrischen Schlages.

e) Wenn Sie mit einem Elektrowerkzeug

im Freien arbeiten, verwenden Sie nur

Verlängerungskabel, die auch für den

Außenbereich geeignet sind. Die Anwendung

eines für den Außenbereich geeigneten

Verlängerungskabels verringert das Risiko eines

elektrischen Schlages.

f) Wenn der Betrieb des Elektrowerkzeuges

in feuchter Umgebung nicht

vermeidbar ist, verwenden Sie einen

Fehlerstromschutzschalter. Der Einsatz eines

Fehlerstromschutzschalters vermindert das Risiko

eines elektrischen Schlages.

3) Sicherheit von Personen

a) Seien Sie aufmerksam, achten Sie darauf,

was Sie tun, und gehen Sie mit Vernunft

an die Arbeit mit einem Elektrowerkzeug.

Benutzen Sie kein Elektrowerkzeug, wenn

Sie müde sind oder unter dem Einfluss von

Drogen, Alkohol oder Medikamenten stehen.

Ein Moment der Unachtsamkeit beim Gebrauch des

Elektrowerkzeuges kann zu ernsthaften Verletzungen

führen.

b) Tragen Sie persönliche Schutzausrüstung und

immer eine Schutzbrille. Das Tragen persönlicher

Schutzausrüstung, wie Staubmaske, rutschfeste

Sicherheitsschuhe, Schutzhelm oder Gehörschutz,

je nach Art und Einsatz des Elektrowerkzeuges,

verringert das Risiko von Verletzungen.

c) Vermeiden Sie eine unbeabsichtigte

Inbetriebnahme. Vergewissern Sie sich,

dass das Elektrowerkzeug ausgeschaltet

ist, bevor Sie es an den Akku anschließen, es

aufnehmen oder tragen. Wenn Sie beim Tragen des

Elektrowerkzeuges den Finger am Schalter haben

oder das Gerät eingeschaltet an die Stromversorgung

anschließen, kann dies zu Unfällen führen.

d) Entfernen Sie Einstellwerkzeuge oder

Schraubenschlüssel, bevor Sie das

Elektrowerkzeug einschalten. Ein Werkzeug oder

Schlüssel, der sich in einem drehenden Geräteteil

befindet, kann zu Verletzungen führen.

e) Vermeiden Sie eine abnormale Körperhaltung.

Sorgen Sie für einen sicheren Stand und halten

Sie jederzeit das Gleichgewicht. Dadurch können

Sie das Elektrowerkzeug in unerwarteten Situationen

besser kontrollieren.

f) Tragen Sie geeignete Kleidung. Tragen Sie

keine weite Kleidung oder Schmuck. Halten Sie

Haare, Kleidung und Handschuhe fern von sich

bewegenden Teilen. Lockere Kleidung, Schmuck

oder lange Haare können von sich bewegenden Teilen

erfasst werden.

g) Wenn Staubabsaug- und -auffangeinrichtungen

montiert werden können, vergewissern Sie

sich, dass diese angeschlossen sind und

richtig verwendet werden. Verwendung einer

Staubabsaugung kann Gefährdungen durch Staub

verringern.

4) Verwendung und Behandlung des

Elektrowerkzeuges

a) Überlasten Sie das Gerät nicht. Verwenden

Sie für Ihre Arbeit das dafür bestimmte

Elektrowerkzeug. Mit dem passenden

Elektrowerkzeug arbeiten Sie besser und sicherer im

angegebenen Leistungsbereich.

20

20V Akku-Pole-Kettensäge D

b) Benutzen Sie kein Elektrowerkzeug, dessen

Schalter defekt ist. Ein Elektrowerkzeug, das sich

nicht mehr ein- oder ausschalten lässt, ist gefährlich

und muss repariert werden.

c) Entfernen Sie den Akku, bevor Sie

Geräteeinstellungen vornehmen, Zubehörteile

wechseln oder das Gerät weglegen.

Diese Vorsichtsmaßnahme verhindert den

unbeabsichtigten Start des Elektrowerkzeuges.

d) Bewahren Sie unbenutzte Elektrowerkzeuge

außerhalb der Reichweite von Kindern auf.

Lassen Sie Personen das Gerät nicht benutzen,

die mit diesem nicht vertraut sind oder

diese Anweisungen nicht gelesen haben.

Elektrowerkzeuge sind gefährlich, wenn Sie von

unerfahrenen Personen benutzt werden.

e) Pflegen Sie Elektrowerkzeuge mit Sorgfalt.

Kontrollieren Sie, ob bewegliche Teile

einwandfrei funktionieren und nicht klemmen,

ob Teile gebrochen oder so beschädigt sind,

dass die Funktion des Elektrowerkzeuges

beeinträchtigt ist. Lassen Sie beschädigte Teile

vor dem Einsatz des Gerätes reparieren. Viele

Unfälle haben ihre Ursache in schlecht gewarteten

Elektrowerkzeugen.

f) Halten Sie Schneidwerkzeuge scharf und

sauber. Sorgfältig gepflegte Schneidwerkzeuge mit

scharfen Schneidkanten verklemmen sich weniger

und sind leichter zu führen.

g) Verwenden Sie Elektrowerkzeug, Zubehör,

Einsatzwerkzeuge usw. entsprechend diesen

Anweisungen. Berücksichtigen Sie dabei die

Arbeitsbedingungen und die auszuführende

Tätigkeit. Der Gebrauch von Elektrowerkzeugen für

andere als die vorgesehenen Anwendungen kann zu

gefährlichen Situationen führen.

5) Verwendung und Behandlung des

Akkuwerkzeugs

a) Laden Sie die Akkus nur in Ladegeräten auf,

die vom Hersteller empfohlen werden. Für ein

Ladegerät, das für eine bestimmte Art von Akkus

geeignet ist, besteht Brandgefahr, wenn es mit

anderen Akkus verwendet wird.

b) Verwenden Sie nur die dafür vorgesehenen

Akkus in den Elektrowerkzeugen. Der Gebrauch

von anderen Akkus kann zu Verletzungen und

Brandgefahr führen.

c) Halten Sie den nicht benutzten Akku fern

von Büroklammern, Münzen, Schlüsseln,

Nägeln, Schrauben oder anderen kleinen

Metallgegenständen, die eine Überbrückung der

Kontakte verursachen könnten. Ein Kurzschluss

zwischen den Akkukontakten kann Verbrennungen

oder Feuer zur Folge haben.

d) Bei falscher Anwendung kann Flüssigkeit aus

dem Akku austreten. Vermeiden Sie den Kontakt

damit. Bei zufälligem Kontakt mit Wasser

abspülen. Wenn die Flüssigkeit in die Augen

kommt, nehmen Sie zusätzlich ärztliche Hilfe

in Anspruch. Austretende Akkuflüssigkeit kann zu

Hautreizungen oder Verbrennungen führen.

6) Service

a) Lassen Sie Ihr Elektrowerkzeug nur von

qualifiziertem Fachpersonal und nur mit

Original-Ersatzteilen reparieren. Damit wird

sichergestellt, dass die Sicherheit des Gerätes

erhalten bleibt.

SICHERHEITSHINWEISE VON

POLE KETTENSÄGE

1. Halten Sie die Pole Kettensäge in ausreichendem

Abstand von elektrischen Freileitungen.

2. Achten Sie auf die Gefahr von Betriebspositionen

sowie die Gefahr, von herabfallenden Ästen getroffen

zu werden, oder von Ästen, die nach dem Aufprall

auf den Boden zurückprallen. Der Bediener kann von

herabfallenden Ästen oder von solchen getroffen

werden, die nach dem Aufprall auf den Boden

zurückprallen. Entfernen Sie die Äste abschnittsweise.

SICHERHEIT HINWEISE FÜR

AKKUPACK

a) Zellen bzw. Akkupack nicht zerlegen, öffnen oder

zerdrücken.

b) Akkupack nicht kurzschließen. Akkupacks

nicht wahllos in einer Schachtel oder

Schublade aufbewahren, wo sie einander

kurzschließen oder durch andere leitfähige

Materialien kurzgeschlossen werden könnten.

Bei Nichtverwendung des Akkupacks ist dieses

von Metallgegenständen fernzuhalten, wie etwa

Büroklammern, Münzen, Nägeln, Schrauben

oder anderen kleinen Metallgegenständen, wo

sich die Batterieklemmen berühren könnten.

Das Kurzschließen der Batterieklemmen kann

Verbrennungen bzw. einen Brand verursachen.

c) Zellen bzw. Akkupacks nicht Hitze oder Feuer

aussetzen. Lagerung in direktem Sonnenlicht

vermeiden.

d) Akkupack nicht mechanischen Stößen

aussetzen.

e) Im Fall, dass Flüssigkeit aus dem Akku austritt,

darf diese nicht in Kontakt mit der Haut oder den

Augen kommen. Sollte dies dennoch geschehen,

den betroffenen Bereich sofort mit viel Wasser

spülen und einen Arzt aufsuchen.

f) Akkupack sauber und trocken halten.

g) Sollten die Klemmen des Akkupacks schmutzig

werden, diese mit einem sauberen, trockenen

Tuch abwischen.

h) Akkupackmuss vor Gebrauch aufgeladen

werden. Immer dieses Anweisungen beachten

und den korrekten Ladevorgang ausführen.

i) Akkupack bei Nichtverwendung nicht längere

Zeit aufladen lassen.

j) Nach längerer Lagerung des Gerätes ist es

eventuell notwendig, die Zellen oder das

Akkupack mehrere Male aufzuladen und zu

entladen, um eine optimale Leistung zu erhalten.

k) Nur mit dem von Worx bezeichneten Ladegerät

aufladen. Kein Ladegerät verwenden, das nicht

La pagina sta caricando ...

Worx WG349E Manuale utente

Worx WG349E Manuale utente

in altre lingue