Indesit WISE 127 X Instructions For Use Manual

Marca: Indesit

Modello: WISE 127 X

Categoria: Lavatrici

Tipo: Instructions For Use Manual

English,1

Contents

Installation, 2-3

Unpacking and levelling, 2

Electric and water connections, 2-3

The first wash cycle, 3

Technical details, 3

Washing machine description, 4-5

Control panel, 4

Display, 5

MEMO Programme, 5

Starting and Programmes, 6

Briefly: how to start a programme, 6

Programme table, 6

Personalisations, 7

Setting the spin cycle, 7

Setting the Delay Timer, 7

Setting the temperature, 7

Functions, 7

Detergents and laundry, 8

Detergent dispenser, 8

Bleach cycle, 8

Preparing your laundry, 8

Special items, 8

Precautions and advice, 9

General safety, 9

Disposal, 9

Saving energy and respecting the environment, 9

Care and maintenance, 10

Cutting off the water or electricity supply, 10

Cleaning your appliance, 10

Cleaning the detergent dispenser, 10

Caring for your appliance door and drum, 10

Cleaning the pump, 10

Checking the water inlet hose, 10

Troubleshooting, 11

Service, 12

Before calling for Assistance, 12

WASHING MACHINE

WISE 127 X

Instructions for use

Èeský,25

Slovenèina,13

Românã,37

Magyar,4 9

 Keep this instruction manual in a safe place for

future reference. Should the appliance be sold,

transferred or moved, make sure the instruction

manual accompanies the washing machine to inform

the new owner as to its operation and features.

 Read these instructions carefully: they contain vital

information on installation, use and safety.

Unpacking and levelling

Unpacking

1. Unpack the washing machine.

2. Check whether the washing machine has been

damaged during transport. If this is the case, do not

install it and contact your retailer.

3. Remove the 4

protective screws and

the rubber washer with

the respective spacer,

situated on the rear of

the appliance (see

figure).

4. Seal the gaps using the plastic plugs provided.

5. Keep all the parts: you will need them again if the

washing machine needs to be moved to another

location.

 Packaging materials are not children's toys.

Levelling

1. Install the washing machine on a flat sturdy floor,

without resting it up against walls, furniture cabinets

or other.

2. If the floor is not

perfectly level, compen-

sate for any unevenness

by tightening or

loosening the adjustable

front feet (see figure);

the angle of inclination,

measured according to

the worktop, must not

exceed 2°.

Levelling your appliance correctly will provide it with

stability and avoid any vibrations, noise and shifting

during operation. If it is placed on a fitted or loose

carpet, adjust the feet in such a way as to allow

enough room for ventilation beneath the washing

machine.

Electric and water connections

Connecting the water inlet hose

1. Insert seal A into the

end of the inlet hose

and screw the latter

onto a cold water tap

with a 3/4 gas threaded

mouth (see figure).

Before making the

connection, allow the

water to run freely until

it is perfectly clear.

2. Connect the other end

of the water inlet hose to

the washing machine,

screwing it onto the

appliance's cold water

inlet, situated on the top

right-hand side on the

rear of the appliance

(see figure).

3. Make sure there are no kinks or bends in the hose.

 The water pressure at the tap must be within the

values indicated in the Technical details table

(on the next page).

 If the water inlet hose is not long enough, contact

a specialist store or an authorised serviceman.

Installation

ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description

Connecting the drain hose

Connect the drain hose,

without bending it, to a

draining duct or a wall

drain situated between

65 and 100 cm from

the floor;

alternatively, place it

over the edge of a

basin, sink or tub,

fastening the duct

supplied to the tap (see

figure). The free end of

the hose should not be

underwater.

 We advise against the use of hose extensions; in

case of absolute need, the extension must have the

same diameter as the original hose and must not

exceed 150 cm in length.

Electric connection

Before plugging the appliance into the mains

socket, make sure that:

 the socket is earthed and in compliance with the

applicable law;

 the socket is able to sustain the appliance's

maximum power load indicated in the Technical

details table (on the right);

 the supply voltage is included within the values i

ndicated on the Technical details table

(on the right);

 the socket is compatible with the washing

machine's plug. If this is not the case, replace

the socket or the plug.

 The washing machine should not be installed in an

outdoor environment, not even when the area is

sheltered, because it may be very dangerous to

leave it exposed to rain and thunderstorms.

 When the washing machine is installed, the mains

socket must be within easy reach.

 Do not use extensions or multiple sockets.

 The power supply cable must never be bent or

dangerously compressed.

 The power supply cable must only be replaced by

an authorised serviceman.

Warning! The company denies all liability if and when

these norms are not respected.

The first wash cycle

Once the appliance has been installed, and before

you use it for the first time, run a wash cycle with

detergent and no laundry, setting the 90°C

programme without a pre-wash cycle.

65 - 100 cm

Technical details

Model

WISE 127 X

Dimensions

59.5 cm wide

85 cm high

40 cm deep

Capacity

from 1 to 4,5 kg

Electric

connections

voltage 220/230 Volts 50 Hz

maximum absorbed power 1850 W

Water

connections

maximum pressure 1 MPa (10 bar)

minimum pressure 0.05 MPa (0.5 bar)

drum capacity 40 litres

Spin speed

up to 1200 rpm

Control

programmes

according to

IEC456 directive

programme 2; temperature 60°C;

run with a load of 4,5 kg.

This appliance is compliant with the

following European Community

Directives:

- 73/23/CEE of 19/02/73 (Low

Voltage) and subsequent amendments

- 89/336/CEE of 03/05/89

(Electromagnetic Compatibility) and

subsequent amendments

- 2002/96/CE

Control panel

Washing machine description

Control knob

Display

Detergent dispenser

SPIN

button

TEMPERATURE

button

START/STOP

button

START/RESET

button

Detergent dispenser to add detergent and fabric

softener (see page 8).

SPIN button to adjust the spin speed or exclude it

altogether (see page 7).

DELAY TIMER button to delay the start of the set

programme for a maximum period of 24 hours

(see page 7).

TEMPERATURE button to adjust the wash tempe-

rature (see page 7).

Display to programme the washing machine and

follow the wash cycle progress (see opposite page).

FUNCTION buttons: to select the functions

available. The button corresponding to the function

selected will remain on.

START/RESET button to start the programmes or

cancel any incorrect settings.

START/STOP button to turn the washing machine

on and off.

Control knob to select the wash programmes.

The knob stays still during the cycle.

DELAY TIMER

button

FUNCTION

Buttons

Display

In addition to being a practical tool to programme your appliance (see page 7), the display provides useful

information concerning the wash cycle.

Once you have pressed the START/RESET button to

start the programme, the display will indicate the

amount of time left until the end of the wash cycle. If

a delayed start has been set (using the Delay Timer,

see page 7), the delay time will be indicated on the

display.

ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description

Door lock:

If the symbol is on, the washing machine door is locked to prevent it from being opened accidentally. To avoid

any damages, wait for the symbol to switch itself off before you open the appliance door.

At the end of the programme, the word END is displayed.

 In the event of an anomaly, an error code will appear, such as: F-01, which should be communicated to the

Service Centre (see page 12).

"MEMO" Programme

This programme allows you to store your favourite or most-used wash cycle.

All you have to do is set the desired programme and, once it has started, turn the KNOB to position

; the

wash cycle will be stored automatically and the word MEMO appears on the display, flashing for a few seconds.

Subsequently, you can start the "MEMO" cycle by simply turning the KNOB to position

; you will be able to

see the temperature/spin cycle/delay timer values by pressing the corresponding buttons; you will also be able to

modify them but this variation will only be valid for the programme in progress and it will not be stored in the

"MEMO" cycle.

If you want to store a new wash cycle, repeat the above-mentioned operations.

Type of fabric and

degree of soil

Programmes

Te m p e -

rature

Detergent

Fabric

softener

Stain removal

option/bleach

Cycle

length

(m inute s)

Description of wash cycle

pre-

wash

Standard

Extremely soiled whites

(sheets, tablecloths, etc.)

90°C   

135

Pre-wash, wash cycle, rinse cycles,

intermediate and final spin cycles

Extremely soiled whites

(sheets, tablecloths, etc.)

90°C  

Delicate/

Traditional

125

Wash cycle, rinse cycles,

intermediate and final spin cycles

Heavily soiled whites and fast

colours

60°C  

Delicate/

Traditional

110

Wash cycle, rinse cycles,

intermediate and final spin cycles

Heavily soiled whites and

delicate colours

40°C  

Delicate/

Traditional

105

Wash cycle, rinse cycles,

intermediate and final spin cycles

Slightly soiled whites and

delicate colours (shirts,

jumpers, etc.)

40°C  

Delicate/

Traditional

Wash cycle, rinse cycles,

intermediate and final spin cycles

Heavily soiled fast colours

(baby linen, etc.)

°C

  Delicate

Wash cycle, rinse cycles, anti-

crease or delicate spin cycle

Heavily soiled fast colours

(baby linen, etc.)

40°C   Delicate

Wash cycle, rinse cycles, anti-

crease or delicate spin cycle

Wool

40°C  

Wash cycle, rinse cycles

anti-

crease and delicate spin cycle

Very delicate fabrics

(curtains, silk, viscose, etc.)

30°C  

Wash cycle, rinse cycles, anti-

crease or draining cycle

Time 4 you

Heavily soiled whites and fast

colours

60°C  

Wash cycle, rinse cycles,

intermediate and final spin cycles

Slightly soiled whites and

delicate colours (shirts,

jumpers, etc.)

40°C  

Wash cycle, rinse cycles,

intermediate and final spin cycles

Delicate colours (all types of

slightly soiled garments)

°C



Wash cycle, rinse cycles,

delicate spin cycle

Delicate colours (all types of

slightly soiled garments)

30°C   30

Wash cycle, rinse cycles and

delicate spin cycle

Sport

Sports shoes

(MAX. 2 pairs)

°C

 50

Cold wash (without detergents),

wash cycle, rinse cycles, and

delicate spin cycle

Fabrics for sportswear

(Tracksuits, shorts, etc.)

30°C   60

Wash cycle, rinse cycles,

intermediate and final spin cycles

MEMO

Allows for any wash cycle to be stored

PARTIAL PROGRAMMES

Rinse 

Delicate/

Traditional

Rinse cycles and spin cycle

Spin Draining and spin cycle

Drain Draining

Starting and Programmes

Programme table

Notes

-For programmes 7 and 8, we advise against exceeding a wash load of 3.5 kg.

-For programme 12 we advise against exceeding a wash load of 2 kg.

-For the anti-crease function: see Easy iron, opposite page. The information contained in the table is purely indicative.

Special programme

Daily (programme 10 for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it only lasts

30 minutes and allows you to save on both time and energy. By setting this programme (10 at 30°C), you can wash

different fabrics together (except for woollen and silk items), with a maximum load of 3 kg.

We recommend the use of liquid detergent.

Briefly: starting a programme

1. Turn the washing machine on by pressing button .

2. Load your laundry into the washing machine and

shut the appliance door.

3. Set the knob to the desired programme. The

estimated duration of the selected programme is

displayed. The temperature and spin speed are

automatically set according to the programme

(to change them, see page 7).

4. Select any functions (see page 7).

5. Add the detergent and any fabric softener

(see page 8).

6. Start he programme by pressing the START/RESET

button.

To cancel it, keep the START/RESET button

pressed for at least 2 seconds.

7. When the programme has ended, the word END is

displayed. Take out your laundry and leave the

appliance door ajar to allow the drum to dry

thoroughly.

8. Turn the washing machine off by pressing button

(see page 5).

Function Effect Comments

Enabled with

programmes:

Stain

removal

Bleaching cycle

designed to

remove the

toughest stains.

Please remember to pour the bleach into extra compartment 4

(se

e page 8)

This function is incompatible with the EASY IRON function.

2, 3, 4,

Rinse cycle.

Extra Rinse

Increases the

efficiency of the

rinse.

Recommended when the appliance has a full load or with large

quantities of detergent.

1, 2, 3, 4, 7,

8, 9, 11, 12,

Rinse cycle.

Easy iron

This option

reduces the

amount of

creasing on

fabrics, making

them easier to

iron.

When this function is set, programmes 4, 5, 6 will end, with the

laundry left to soak (Anti-crease), and the relative button flashes:

- to conclude the cycle, press the START/RESET button or the

EASY IRON button;

- to run the draining cycle alone, set the knob to the relative

symbol and press the START/RESET button.

This function is incompatible with the STAIN REMOVAL function.

3, 4, 5, 6, 7, 8,

9, Rinse

cycle.

ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description

Personalisations

Setting the spin cycle

If, when the appliance is switched on, the KNOB is positioned on

a programme with a spin cycle, a fixed

appears. Press button

and the maximum spin speed allowed for the programme set

will be displayed, and the

icon flashes. Press it again and the

values lower until they reach OFF, which indicates that the spin

cycle has been excluded (press it again to go back to the

maximum value); stop on the desired speed, after approximately

2 seconds the setting is accepted: the symbol

remains fixed.

The spin cycle setting is enabled with all the programmes except

for 6 and the Draining cycle.

Setting the Delay Timer

Press the button and you will see the word OFF on the

display, while the relative symbol flashes.

Press the button again and "1h" appears, that is, a delay of one

hour (this can reach up to 24h); stop on the "desired" delay; after

approximately 2 seconds the setting is accepted, following which,

the time for the set programme appears on the display and the

symbol

remains on.

If you now press the START/RESET button, the set "delay"

appears; this decreases every hour until the start of the cycle. In

this phase, the "delay" can only be modified by decreasing it.

The Delay Timer regulation is enabled with all programmes.

Setting the temperature

If, when the appliance is switched on, the KNOB is positioned on a programme for which the temperature needs

to be regulated, a fixed

appears. Press button and the maximum temperature allowed for the programme set

will be displayed and the

icon flashes. Press it again and the temperature lowers until it reaches OFF, which

indicates a cold wash cycle (press it again to go back to the maximum value); stop on the desired value, after

approximately 2 seconds the setting is accepted: the symbol

remains fixed.

The temperature adjustment is enabled with all wash programmes.

Functions

To enable a function:

1. press the button corresponding to the desired function, according to the table below;

2. the function is enabled when the corresponding button is illuminated.

Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the

programme set.

If you set a function that is incompatible with another function you selected previously, only the last one selected

will be enabled.

FUNCTION buttons

Detergent dispenser

Good washing results also depend on the correct

dose of detergent: adding too much detergent won't

necessarily make for a more efficient wash, and may

in fact cause build up on the interior of your

appliance and even pollute the environment.

Open up the detergent

dispenser and pour in

the detergent and fabric

softener, as follows.

compartment 1: Detergent for pre-wash

(powder)

Before pouring in the detergent, make sure that

extra compartment 4 has been removed.

compartment 2: Detergent for the wash cycle

(powder or liquid)

Liquid detergent should only be poured in

immediately prior to the wash cycle start.

compartment 3: Additives (fabric softeners, etc.)

The fabric softener should not overflow from the grid.

extra compartment 4: Bleach

 Do not use hand wash detergent because it may

form too much foam.

Bleach cycle

 Traditional bleach should be used on sturdy

white fabrics, and delicate bleach for coloured

fabrics, synthetics and for wool.

Place extra

compartment 4,

provided, into

compartment 1.

When pouring in the

bleach, be careful not to

exceed the "max" level

indicated on the central

pivot (see figure).

To run the bleach cycle alone, pour the bleach into extra

compartment 4, set the Rinse programme

and

enable the Stain removal function (see page 7).

To bleach during a wash cycle, pour in the detergent

and fabric softener, set the desired programme and

enable the Stain removal function (see page 7).

The use of extra compartment 4 excludes the

possibility of using the pre-wash cycle.

Preparing your laundry

 Divide your laundry according to:

- the type of fabric/the symbol on the label.

- the colours: separate coloured garments from

whites.

 Empty all pockets and check for loose buttons.

 Do not exceed the weight limits stated below,

which refer to the weight when dry:

Sturdy fabrics: max 4,5 kg

Synthetic fabrics: max 2.5 kg

Delicate fabrics: max 2 kg

Wool: max 1 kg

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1,200 g

1 towel 150-250 g

Special items

Curtains: fold curtains and place them in a pillow

case or mesh bag. Wash them separately without

exceeding half the appliance load. Use programme 6

which excludes the spin cycle automatically.

Quilted coats and windbreakers: if they are

padded with goose or duck down, they can be

machine-washed. Turn the garments inside out and

load a maximum of 2-3 kg, repeating the rinse cycle

once or twice and using the delicate spin cycle.

Wool: for best results, use a specific detergent,

taking care not to exceed a load of 1 kg.

Detergents and laundry

Precautions and advice

ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description

 The washing machine was designed and built in

compliance with the applicable international safety

regulations. The following information is provided for

your safety and should consequently be read carefully.

General safety

 This appliance has been designed for non-

professional, household use and its functions must

not be changed.

 This washing machine should only be used by

adults and in accordance with the instructions

provided in this manual.

 Never touch the washing machine when barefoot

or with wet or damp hands or feet.

 Do not pull on the power supply cable to unplug

the appliance from the electricity socket. Pull the

plug out yourself.

 Do not open the detergent dispenser while the

appliance is in operation.

 Do not touch the drain water as it could reach

very high temperatures.

 Never force the washing machine door: this could

damage the safety lock mechanism designed to

prevent any accidental openings.

 In the event of a malfunction, do not under any

circumstances touch internal parts in order to

attempt repairs.

 Always keep children well away from the

appliance while in operation.

 The appliance door tends to get quite hot during

the wash cycle.

 Should it have to be moved, proceed with the

help of two or three people and handle it with the

utmost care. Never try to do this alone, because

the appliance is very heavy.

 Before loading your laundry into the washing

machine, make sure the drum is empty.

Disposal

 Disposing of the packaging material:

observe local regulations, so the packaging can

be re-used.

 The European Directive 2002/96/EC on Waste

Electrical and Electronic Equipment, requires that

old household electrical appliances must not be

disposed of in the normal unsorted municipal waste

stream. Old appliances must be collected

separately in order to optimise the recovery and

recycling of the materials they contain and reduce

the impact on human health and the environment.

The crossed out "wheeled bin" symbol on the

product reminds you of your obligation, that when

you dispose of the appliance it must be separately

collected.

Consumers should contact their local authority or

retailer for information concerning the correct

disposal of their old appliance.

Saving energy and respecting the

environment

Environmentally-friendly technology

If you only see a little water through your appliance

door, this is because thanks to the latest Indesit

technology, your washing machine only needs less

than half the amount of water to get the best results:

an objective reached to respect the environment.

Saving on detergent, water,

energy and time

 To avoid wasting resources, the washing machine

should be used with a full load. A full load instead of

two half loads allows you to save up to 50% on energy.

 The pre-wash cycle is only necessary on

extremely soiled garments. Avoiding it will save on

detergent, time, water and between 5 and 15%

energy.

 Treating stains with a stain remover or leaving them

to soak before washing will cut down the need to

wash them at high temperatures. A programme at

60°C instead of 90°C or one at 40°C instead of

60°C will save up to 50% on energy.

 Use the correct quantity of detergent depending

on the water hardness, how soiled the garments

are and the amount of laundry you have, to avoid

wastage and to protect the environment: despite

being biodegradable, detergents do contain

ingredients that alter the natural balance of the

environment. In addition, avoid using fabric

softener as much as possible.

 If you use your washing machine from late in the

afternoon until the early hours of the morning, you

will help reduce the electricity board's peak load.

The Delay Timer option (see page 7) helps to

organise your wash cycles accordingly.

 If your laundry has to be dried in a tumble dryer,

select a high spin speed. Having the least water

possible in your laundry will save you time and

energy in the drying process.

Care and maintenance

Cutting off the water or electricity

supply

 Turn off the water tap after every wash. This will

limit the wear of your appliance's water system

and also prevent leaks.

 Unplug your appliance when cleaning it and

during all maintenance operations.

Cleaning your appliance

The exterior and rubber parts of your appliance can

be cleaned with a soft cloth soaked in lukewarm

soapy water. Do not use solvents or abrasives.

Cleaning the detergent dispenser

Remove the dispenser

by pulling it out (see

figure).

Wash it under running

water; this operation

should be repeated

frequently.

Caring for your appliance door and

drum

 Always leave the appliance door ajar to prevent

unpleasant odours from forming.

Cleaning the pump

The washing machine is fitted with a self-cleaning

pump that does not require any maintenance.

Sometimes, small items (such as coins or buttons)

may fall into the pre-chamber that protects the

pump, situated in the lower part of the same.

 Make sure the wash cycle has ended and unplug

the appliance.

To access the pre-chamber:

1. using a screwdriver,

remove the cover panel

on the lower front of the

washing machine (see

figure);

2. unscrew the lid

rotating it anti-

clockwise (see figure): a

little water may trickle

out. This is perfectly

normal;

3. clean the interior thoroughly;

4. screw the lid back on;

5. reposition the panel, making sure the hooks are

securely in place before you push it onto the

appliance.

Checking the water inlet hose

Check the water inlet hose at least once a year. If

you see any cracks, replace it immediately: during

the wash cycles, water pressure is very strong and

a cracked hose could easily split open.

 Never use hoses that have already been used.

Your washing machine could fail to work. Before calling for Assistance (see page 12), make sure the problem

can't easily be solved by consulting the following list.

Troubleshooting

Problem

The washing machine won't

start.

The wash cycle won't start.

The washing machine fails to

load water (The wording H2O is

displayed).

The washing machine

continuously loads and unloads

water.

The washing machine does not

drain or spin.

The washing machine vibrates

too much during the spin cycle.

The washing machine leaks.

There is too much foam.

Possible causes/Solution:

 The appliance is not plugged into the socket, or not enough to

make contact.

 There has been a power failure.

 The appliance door is not shut properly (the word DOOR is

displayed).

 The

button has not been pressed.

 The START/RESET button has not been pressed.

 The water tap is not turned on.

 A delayed start has been set (using the Delay Timer, see page 7).

 The water inlet hose is not connected to the tap.

 The hose is bent.

 The water tap is not turned on.

 There is a water shortage.

 The water pressure is insufficient.

 The START/RESET button has not been pressed.

 The drain hose is not fitted between 65 and 100 cm from the floor

(see page 3).

 The free end of the hose is underwater (see page 3).

 The wall drainage system doesn't have a breather pipe.

If the problem persists even after these checks, turn off the water tap,

switch the appliance off and call for Assistance. If the dwelling is on one of

the upper floors of a building, there may be drain trap problems causing the

washing machine to load and unload water continuously. In order to avoid

such an inconvenience, special anti-drain trap valves are available in shops.

 The programme does not foresee the draining: some programmes

require enabling the draining manually (see page 6).

 The Easy iron option is enabled: to complete the programme, press

the START/RESET button (see page 7).

 The drain hose is bent (see page 3).

 The drain duct is clogged.

 The drum was not unblocked correctly during installation (see page 2).

 The washing machine is not level (see page 2).

 The washing machine is closed in between furniture cabinets and

the wall (see page 2).

 The water inlet hose is not screwed on correctly (see page 2).

 The detergent dispenser is obstructed (to clean it, see page 10).

 The drain hose is not secured properly (see page 3).

 The detergent is not suitable for machine washing (it should bear

the definition "for washing machines" or "hand and machine wash",

or the like).

 You used too much detergent.

ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description

Before calling for Assistance:

 Check whether you can solve the problem on your own (see page 11);

 Restart the programme to check whether the problem has been solved;

 If this is not the case, contact an authorised Technical Service Centre on the telephone number

provided on the guarantee certificate.

 Always request the assistance of authorised servicemen.

Notify the operator of:

 the type of problem;

 the appliance model (Mod.);

 the serial number (S/N).

This information can be found on the data plate situated on the rear of the washing machine.

Service

Slovenèina

Vsebina

Namestitev, 14-15

Odstranitev embalae in izravnavanje, 14

Prikljuèitev na vodovodno in elektrièno napeljavo, 14-15

Prvo pranje, 15

Tehnièni podatki, 15

Opis pralnega stroja, 16-17

Upravljalna ploèa, 16

Prikazovalnik, 17

Program MEMO, 17

Zagon in razlièni pralni programi, 18

Na kratko: kako zagnati program pranja, 18

Tabela pralnih programov, 18

Posebne nastavitve, 19

Nastavitev centrifuge, 19

Funkcija delay timer, 19

Nastavitev temperature, 19

Funkcije, 19

Pralna sredstva in perilo, 20

Predal za pralna sredstva, 20

Pranje z belilom, 20

Priprava perila, 20

Posebne vrste perila, 20

Opozorila in nasveti, 21

Varnost, 21

Ravnanje z odpadnim materialom, 21

Varèevanje in skrb za okolje, 21

Vzdrevanje in èièenje, 22

Odklop vodovodne in elektriène napeljave, 22

Èièenje pralnega stroja, 22

Èièenje predala za pralna sredstva, 22

Vzdrevanje vratc in bobna, 22

Èièenje èrpalke, 22

Pregled cevi za dotok vode, 22

Motnje in njihovo odpravljanje, 23

Pomoè, 24

Preden poklièete pooblaèeni servis, 24

PRALNI STROJ

WISE 127 X

Navodila za uporabo

 Shranite to knjiico, da jo boste lahko po potrebi

uporabili. Èe boste pralni stroj prodali, ga nehali

uporabljati ali premestili drugam, naj bo knjiica pri

njem, tako da se bo novi lastnik lahko seznanil z

delovanjem in ustreznimi opozorili.

 Pozorno preberite navodila. Našli boste pomembne

informacije glede namestitve, uporabe in

zagotavljanja varnosti.

Odstranitev embalae in izravnavanje

Odstranitev embalae

1. Odstranite embalao

2. Preverite, da ni bil pralni stroj med prevozom

pokodovan. Èe je pokodovan, ga ne prikljuèite,

ampak obvestite prodajalca.

3. Odstranite vse 4

zaèitne vijake in

gumico z distanènikom

na zadnji strani (glej

sliko).

4. S priloenimi plastiènimi èepi zaprite odprtine.

5. Vse odstranjene dele shranite. Èe bo pralni stroj

potrebno prevaati, jih bo treba spet namestiti.

 Embalaa ni primerna kot igraèa za otroke

Izravnavanje

1. Pralni stroj namestite na ravna in trda tla. Naj se

ne dotika sten, pohištva ipd.

2. Èe tla niso

popolnoma vodoravna, z

odvijanjem ali

zavijanjem prednjih

noic uravnajte lego

pralnega stroja (glej

sliko). Nagib na delovni

površini ne sme

presegati 2°.

Natanèno izravnanje poveèa stabilnost pralnega

stroja in prepreèuje vibracije, hrup in premikanje

med delovanjem. Èe je na tleh tapison ali preproga,

uravnajte noice tako, da bo pod pralnim strojem

ostalo nekaj prostora za prezraèevanje.

Prikljuèitev na vodovodno in elektrièno

napeljavo

Prikljuèitev dotoène cevi za vodo

1. Vstavite tesnilo A na

konec dotoène cevi; cev

privijte na pipo za dotok

hladne vode s ¾

navojem (glej sliko).

Predtem pustite teèi

vodo, dokler ne bo

èista.

2. Dotoèno cev privijte

na ustrezen prikljuèek

na zadnji strani

pralnega stroja zgoraj

desno (glej sliko).

3. Pazite, da cev ne bo prepognjena ali stisnjena.

 Vodni tlak v pipi mora biti v mejah vrednosti, ki so

zapisane v tabeli tehniènih podatkov (glej naslednjo

stran).

 Èe dotoèna cev ni dovolj dolga, se obrnite na

specializirano trgovino ali na pooblaèeni servis.

Namestitev

Namestitev odtoène cevi

Odtoèno cev, ki ne sme

biti prepognjena,

prikljuèite na odtoèni

sistem ali na odtok na

zidu, ki sta v viini 65 -

100 cm od tal;

ali jo naslonite na rob

umivalnika ali korita; s

priloenim vodilom jo

pritrdite na pipo (glej

sliko). Prosti konec

odtoène cevi ne sme

biti potopljen v vodo.

 Odsvetujemo uporabo podaljka za odtoèno cev.

Èe je to nujno, naj ima podaljek isti premer in naj

ne bo dalji od 150 cm.

Prikljuèitev na elektrièno napeljavo

Preden pralni stroj prikljuèite na elektrièno

napeljavo, se preprièajte, èe:

 je elektrièni prikljuèek ozemljen in neoporeèen;

 elektrièni prikljuèek zmore najveèjo obremenitev

moèi pralnega stroja, ki je zapisana v tabeli

tehniènih podatkov (glej poleg);

 elektrièna napetost v vtiènici ustreza vrednostim v

tabeli tehniènih podatkov (glej poleg);

 vtiènica ustreza vtikaèu pralnega stroja. V

nasprotnem primeru je treba zamenjati vtiènico

ali vtikaè.

 Pralni stroj ne sme biti nameèen na prostem

(èeprav je pod streho), saj ga je zelo nevarno

izpostavljati deju in nevihtam.

 Ko je pralni stroj nameèen, naj bo vtiènica lahko

dosegljiva.

 Ne uporabljajte podaljškov in razdelivcev.

 Kabel naj ne bo prepognjen ali stisnjen.

 Elektrièni kabel lahko zamenja le pooblaèeni

serviser.

Pozor! V primeru neupotevanja teh navodil nae

podjetje ne sprejema nobene odgovornosti.

Prvo pranje

Po prikljuèitvi in pred uporabo zaenite prvo pranje z

detergentom in brez perila. Prvo pranje naravnajte

na 90°C brez predpranja.

PomoèMotnjeOpozorila VzdrevanjeProgrami Pralna sredstvaNamestitev Opis

65 - 100 cm

Tehnièni podatki

Model

WISE 127 X

Dimenzije

irina 59,5 cm

viina 85 cm

globina 40 cm

Zmogljivost

1 - 4,5 kg

Elektrièna napeljava

napetost 220/230 V, 50 Hz

maksimalna poraba moèi 1850 W

Vodovodni prikljuèek

najveèji dovoljeni tlak 1 MPa (10 b)

najmanji dovoljeni tlak 0,05 MPa (0,5 b)

prostornina bobna 40 litrov

Hitrost centrifuge

do 1200 vrtljajev na minuto

Kontrolni program

po standardu IEC456

program 2; temperatura 60°C;

z obremenitvijo 4,5 kg.

Pralni stroj je izdelan v skladu z

veljavnimi mednarodnimi predpisi:

- EEC 73/23 z dne 19.2.1973 (Nizka

napetost) s kasnejimi spremembami

- EEC 89/336 z dne 3.5.1989

(Elektromagnetna kompatibilnost)

s kasnejimi spremembami

- 2002/96/CE

Upravljalna ploèa

Opis pralnega stroja

Gumb

Prikazovalnik

Predal za pralna sredstva

Tipka

CENTRIFUGA

Tipka

TEMPERATURA

Tipka

VKLOP/IZKLOP

Tipka

START/RESET

Predal za pralna sredstva za odmerjanje

detergentov in dodatkov (glej str. 20).

Tipka CENTRIFUGA za nastavitev hitrosti

centrifuge ali njen izklop (glej str. 19).

S tipko DELAY TIMER lahko zakasnimo zaèetek

pranja in sicer za najveè 24 ur (glej str. 19).

Tipka TEMPERATURA za nastavitev temperature

pranja (glej str. 19).

Prikazovalnik za nastavitev pralnega programa in

spremljanje poteka pranja (glej naslednjo stran).

Tipke FUNKCIJ: za nastavitev razpololjivih funkcij.

Tipka za izbrano funkcijo bo ostala prigana.

Tipka START/RESET za zagon programov ali izbris

napaènih nastavitev.

Tipka VKLOP/IZKLOP za vklop in izklop pralnega

stroja.

Gumb za izbiranje programov.

Med potekom pranja se gumb ne premika.

Tipka

DELAY TIMER

Tipke

FUNKCIJ

PomoèMotnjeOpozorila VzdrevanjeProgrami Pralna sredstvaNamestitev Opis

Prikazovalnik

Prikazovalnik slui za programiranje pranja (glej str. 19), poleg tega pa nas tudi sproti obveèa o poteku pranja.

Ko pritisnemo na tipko START/RESET za zagon

pralnega programa, se na prikazovalniku pokae

èas, ki bo potreben do konca pranja. Èe je

nastavljena zakasnitev zaèetka pranja, bo to

prikazano (Delay Timer, glej str. 19)

Vratca so blokirana:

Prigani znak pomeni: vratca so blokirana, da jih ne bi pomotoma odprli. Preden odprete vratca, morate

poèakati, da znak ugasne, sicer lahko pride do pokodb.

Na koncu pranja se pokae napis END.

 Èe pride do nepravilnosti, se pokae koda napake, na primer F-01. Kodo napake sporoèimo na pooblaèeni

servis (glej str. 24).

Program MEMO

S to funkcijo lahko shranimo v spomin pralni program, ki ga najraje ali najpogosteje uporabljamo.

Nastavimo eljeni program, ga zaenemo in nato zavrtimo GUMB na poloaj

. Pralni program se bo

samodejno shranil v spomin in na prikazovalniku se bo za nekaj trenutkov pokazal utripajoèi napis MEMO.

Kasneje lahko ta v spomin shranjeni program MEMO zaenemo preprosto tako, da GUMB zavrtimo na

poloaj

; s pritiskom na ustrezne tipke boste lahko preverili nastavljene vrednosti temperature, centrifuge

in zakasnitve zaèetka pranja; te vrednosti boste lahko tudi spremenili, pri tem pa bodo spremembe veljale le

za tekoèi pralni program in ne bodo shranjene v spomin (v program MEMO).

Èe elite v spomin shraniti drug pralni program, ponovite zgoraj opisani potek.

Lastnosti tkanine in stopnja

umazanosti

Program

Tempe-

ratura

Detergent

Meh

alec

Uporaba

belila

Trajanje

programa

(v minutah)

Potek programa

predp-

ranje

pranje

Standardno perilo

Belo perilo, zelo moèno umazano

(rjuhe, prti ipd.)

90°C

 

135

Predpranje, pranje, izpiranje,

vmesno in konèno o¡zemanje

Belo perilo, zelo moèno umazano

(rjuhe, prti ipd.)

90°C



¡z

no /

navadno

125

Pranje, izpiranje, vmesno in

konèno o

¡z

emanje

B elo perilo in vzdr¡zljivo barvno

perilo, moèno umazano

60°C



¡z

no /

navadno

110

Pranje, izpiranje, vmesno in

konèno o

¡z

emanje

Belo in obèutljivo barvno perilo,

moèno umazano

40°C



¡z

no /

navadno

105

Pranje, izpiranje, vmesno in

konèno o

¡z

emanje

Malo umazano belo perilo in

obèutljivo barvno perilo

(srajce, majice ipd.)

40°C



¡z

no /

navadno

Pranje, izpiranje, vmesno in

konèno o

¡z

emanje

V zdr¡zljivo barvno perilo, moèno

umazano (oblaèila za dojenèke ipd.)

°C

ne

¡z

Pranje, izpiranje, mehèanje

ali blago o

¡z

emanje

Vzdr

¡z

ljivo barvno perilo, moèno

umazano (oblaèila za dojenèke ipd.)

40°C

ne

¡z

Pranje, izpiranje, mehèanje ali

blago o

¡z

emanje

Volna

40°C



Pranje, izpiranje

mehèanje in

blago o

¡z

emanje

Zelo obèutljive tkanine (zavese,

svila, viskoza ipd.)

30°C



Pranje, izpiranje, mehèanje ali

izpraznitev

Time 4 you

B elo perilo in vzdr¡zljivo barvno

perilo, moèno umazano

60°C



Pranje, izpiranje, vmesno in

konèno o

¡z

emanje

Malo umazano belo perilo in obèutljivo

barvno perilo (srajce, majice ipd.)

40°C



Pranje, izpiranje, vmesno in

konèno o

¡z

emanje

O bèutljivo barvno perilo

(malo umazano perilo vseh vrst)

°C



Pranje, izpiranje in blago

¡z

emanje

O bèutljivo barvno perilo

(malo umazano perilo vseh vrst)

30°C

 30

Pranje, izpiranje in blago

¡z

emanje

portna oblaèila

portne copate

(maksimalno 2 para.)

°C

 50

Pranje brez detergenta, pranje,

izpiranje in blago o¡zemanje

Tkanine portnih oblaèil (trenirke,

nogavice ipd.)

30°C

 60

Pranje, izpiranje, vmesno in

konèno o

¡z

emanje

MEMO

Omogoèa shranitev v spomin kateregakoli pralnega programa

DELNI PROGRAMI

Izpiranje 

¡z

no /

navadno

Izpiranje in o

¡z

emanje

¡z

emanje Izpraznitev in o

¡z

emanje

Izpraznitev Izpraznitev

Zagon in razlièni pralni programi

Tabela pralnih programov

Na kratko: kako zagnati program pranja

1. Prigite pralni stroj s pritiskom na tipko .

2. Perilo dajte v pralni stroj in zaprite vratca.

3. Z gumbom nastavite eljeni program. Na

prikazovalniku se bo pokazal predvideni èas

pranja. Temperatura in hitrost centrifuge se

samodejno naravnata glede na izbrani program (za

spremembo nastavitve glej str. 19).

4. Izberite funkcije po elji (glej str. 19).

5. Vstavite detergent in dodatke (glej str. 20).

6. Poenite program s pritiskom na tipko START/

RESET.

Za preklic drite tipko START/RESET najmanj 2

sekundi.

7. Ob zakljuèku programa se pokae napis END.

Perilo vzemite ven, vratca pa pustite priprta, da

se boben osui.

8. Ugasnite pralni stroj s pritiskom na tipko

Opombi

-Pri programih 7 - 8 je priporoèljiva manja kolièina perila: ne veè kot 3,5 kg.

-Pri programu 12 je priporoèljivo, da perilo v pralnem stroju ne presega 2 kg.

-Podatki v tej tabeli so zgolj informativni. Za opis postopka proti meèkanju glej tabelo na naslednji strani.

Posebni program

Polurni program (program 10 za sintetiko) je posebej prilagojen za pranje manj umazanega perila v èim

krajem èasu: traja samo 30 minut in tako prihrani energijo in èas. S tem programom (program 10 pri 30°C)

je mogoèe prati skupaj razliène tkanine (razen volne in svile), ki skupaj ne smejo tehtati veè kot 3 kg.

Pri tem programu priporoèamo uporabo tekoèega detergenta.

(glej str. 17).

Posebne nastavitve

PomoèMotnjeOpozorila VzdrevanjeProgrami Pralna sredstvaNamestitev Opis

Nastavitev centrifuge

Èe je ob vkljuèitvi pralnega stroja GUMB naravnan na program,

ki omogoèa nastavitev hitrosti centrifuge, znak

miruje (ne

utripa). Ob pritisku na tipko

se pokae maksimalna hitrost

centrifuge, ki jo nastavljeni program omogoèa; znak

pri tem

utripa. Z nadaljnjim pritiskanjem se hitrost centrifuge zniuje

vse do napisa OFF, ki oznaèuje izklop centrifuge (ob ponovnem

pritisku se spet pokae maksimalna vrednost). Ustavite se pri

eljeni hitrosti; po priblino dveh sekundah bo izbira sprejeta:

znak

bo obmiroval. Hitrost centrifuge je mogoèe uravnavati

pri vseh programih, razen pri programih 6 in izèrpanje vode.

Funkcija delay timer

Ob pritisku na tipko se bo na prikazovalniku pokazal napis

OFF, ustrezni znak pa bo utripal.

Ob ponovnem pritisku se na prikazovalniku pokae napis 1h,

to je zakasnitev za eno uro, in tako naprej vse do 24h. Ustavite

se pri eljeni zakasnitvi; po priblino dveh sekundah bo izbira

sprejeta: na prikazovalniku se bo pokazala èas zakasnitve

pralnega programa in znak

bo obmiroval.

Ob pritisku na tipko START/RESET se bo sedaj pokazal èas

zakasnitve, ki se bo zmanjeval vsako uro vse do zagona pranja. V tej fazi je zakasnitev mogoèe

spremeniti le v smer manje zakasnitve. Funkcijo Delay Timer je mogoèe uporabiti za vse pralne programe.

Nastavitev temperature

Èe je ob vkljuèitvi pralnega stroja GUMB naravnan na program, ki omogoèa nastavitev temperature, znak

miruje (ne utripa). Ob pritisku na tipko se pokae maksimalna temperatura, ki jo nastavljeni program

omogoèa; znak

pri tem utripa. Z nadaljnjim pritiskanjem se temperatura zniuje vse do napisa OFF, ki

oznaèuje pranje s hladno vodo (ob ponovnem pritisku se spet pokae maksimalna temperatura). Ustavite se

pri eljeni temperaturi; po priblino dveh sekundah bo izbira sprejeta: znak

bo obmiroval.

Temperaturo je mogoèe uravnavati pri vseh pralnih programih.

Funkcije

Pralni stroj omogoèa razliène funkcije za doseganje takne stopnje èistosti, kakrno elite. Za izbiro

posameznih funkcij:

1. pritisnite tipko za ustrezno funkcijo (glej spodnjo tabelo);

2. prigana tipka pomeni, da je funkcija aktivirana.

Pozor: Hitro utripanje tipke oznaèuje, da funkcija ni zdruljiva z izbranim programom.

Èe boste izbrali dve med seboj nezdruljivi funkciji, bo aktivirana samo tista, ki ste jo izbrali nazadnje.

Funkcije Uèinek Opombe za uporabo

razpolago:

Belilo

Postopek pranja z

belilom za odstranitev

trdovratnih made±zev.

Ne pozabite dati belila v dodatno posodico 4

(glej str.

20).

Ni zdruzljivo s funkcijo

Postopek proti mehèanju

pri

programih

2, 3, 4,

"izpiranje"

Dodatno

izpiranje

Poveèa uèinek

izpiranja.

Priporoèljivo pri maksimalni obremenitvi (5 kg) pralnega stroja ali pri

veèjih odmerkih detergenta.

pri

programih

1, 2, 3, 4,

7, 8, 9, 11, 12,

"izpiranje"

Postopek

proti

meèkanju

Ubla±zi meèkanje

tkanin in tako olaja

likanje.

Ob nastavitvi te funkcije se programi 4, 5, 6 prekinejo v fazi mehèanja

perila (postopek proti meèkanju); pri tem ustrezni znak utripa.

- za dokonèanje pranja pritisnite na tipko START/RESET ali na

funkcijo

Postopek proti mehèanju

- èe ±zelite tu konèati program, naravnajte gumb na znak in pritisnite

na tipko START/RESET.

Ni zdruzljivo s funkcijo

Belilo.

pri

programih

3, 4, 5, 6,

7, 8, 9,

"izpiranje"



Tipke FUNKCIJ

Predal za pralna sredstva

Dobri uèinki pranja so odvisni tudi od pravilnega

odmerjanja pralnih sredstev. Èe z njimi pretiravamo,

perilo ni niè bolje oprano, poveèamo pa verjetnost

nastajanja usedlin v pralnem stroju in

onesnaevanje okolja.

Odprite predal za pralna

sredstva in v

posamezne prekate

dajte detergent oziroma

dodatke po naslednjih

navodilih:

Prekat 1: detergent za predpranje (v prahu)

Preden odmerite ustrezno kolièino detergenta, se

preprièajte, da v prekat ni vstavljena dodatna

posodica 4.

Prekat 2: detergent za pranje (v prahu ali tekoèini)

Tekoèi detergent smemo vliti v prekat le neposredno

pred pranjem.

Prekat 3: dodatki (mehèalec idr.)

Mehèalec naj se ne izliva preko reetke prekata.

Dodatna posodica 4: belilo

 Ne uporabljajte detergentov za roèno pranje, ker se

preveè penijo.

Pranje z belilom

 Navadno belilo uporabljamo za bele in vzdrljive

tkanine, neno belilo pa za barvne, sintetiène in

volnene tkanine.

Priloeno dodatno

posodico 4 vstavite v

prekat 1.

Belilo naj ne presega

oznake max na

stebrièku (glej sliko).

Èe elite opraviti zgolj pranje z belilom, dajte belilo v

dodatno posodico 4, naravnajte program izpiranje

in vkljuèite monost belilo (glej str. 19). Èe elite

uporabiti belilo kot dodatek med sicernjim potekom

pranja, dajte detergent in dodatke v ustrezne prekate,

izberite eljeni program in vkljuèite monost belilo

(glej str. 19).

Uporaba dodatne posodice 4 ni zdruljiva s predpranjem.

Priprava perila

 Perilo razvrstite po:

- vrsti tkanine / znaku na etiketi.

- barvi: loèite barvno perilo od belega perila.

 Izpraznite epe in preglejte gumbe.

 Ne obremenite pralnega stroja preko navedene

tee suhega perila:

Vzdrljive tkanine: najveè 4,5 kg

Sintetiène tkanine: najveè 2,5 kg

Obèutljive tkanine: najveè 2 kg

Volna: najveè 1 kg

Koliko tehta perilo?

1 rjuha 400-500 gr.

1 prevleka za blazino 150-200 gr.

1 prt 400-500 gr.

1 kopalni plaè 900-1.200 gr.

1 brisaèa 150-250 gr.

Posebne vrste perila

Zavese: Namestite jih v prevleko ali mreasto vreèo.

Perite jih posebej, njihova tea pa naj ne presega

poloviène obremenitve. Uporabite program 6, ki

samodejno izkljuèi oemanje.

Pernice in bunde s puhom: Èe je polnilo iz gosjega

ali raèjega perja, je mono pranje v pralnem stroju.

Oblaèila obrnite. Perila naj ne bo veè kot 2-3 kg.

Ponovno izpiranje vkljuèite e enkrat ali dvakrat in

uporabite neno oemanje.

Volna: Za bolji uèinek uporabite poseben

detergent za volno. Perila naj ne bo veè kot 1 kg.

Pralna sredstva in perilo

La pagina sta caricando ...

Indesit WISE 127 X Instructions For Use Manual

Marca: Indesit

Modello: WISE 127 X

Categoria: Lavatrici

Tipo: Instructions For Use Manual

Scarica il pdf

rapporto

in altre lingue

English: Indesit WISE 127 X
slovenčina: Indesit WISE 127 X
română: Indesit WISE 127 X

Indesit WISE 127 X Instructions For Use Manual

Indesit WISE 127 X Instructions For Use Manual

in altre lingue

Documenti correlati

Altri documenti