Brooks GF / GI Istruzioni per l'uso

Tipo
Istruzioni per l'uso
SolidSense II
®
Series
Installation and Operation Manual
X-PR-SolidSense II-PT-eng
Part Number: 541B160AAG
May, 2019
Brooks
®
SolidSense II
®
Series
Pressure Transducer
SolidSense II ATEX
Pressure Transmitter
Pigtail Conguration
SolidSense II
Pressure Transducer
15-Pin Flow Thru
Conguration
SolidSense II
Pressure Transducer
with Bendix
®
Conguration
SolidSense II
Pressure Transducer
with Integrated Digital
Display
Installation and Operation Manual
X-PR-SolidSense II-PT-eng
Part Number: 541B160AAG
May, 2019
SolidSense II
®
Series
ESD (Electrostatic Discharge)
CAUTION: This instrument contains electronic components that are susceptible to damage by static electricity. Proper handling procedures must be observed
during the removal, installation or other handling of internal circuit boards or devices.
Handling Procedure:
1. Power to unit must be removed.
2. Personnel must be grounded, via a wrist strap or other safe, suitable means before any printed circuit card or other internal device is installed,
removed or adjusted.
3. Printed circuit cards must be transported in a conductive container. Boards must not be removed from protective enclosure until immediately before
installation. Removed boards must immediately be placed in protective container for transport, storage or return to factory.
Comments
This instrument is not unique in its content of ESD (electrostatic discharge) sensitive components. Most modern electronic designs contain components
that utilize metal oxide technology (NMOS, SMOS, etc.). Experience has proven that even small amounts of static electricity can damage or destroy these
devices. Damaged components, even though they appear to function properly, exhibit early failure.
Brooks Instrument designs, manufactures and tests its products to meet many national and international standards. These products must be properly
installed, operated and maintained to ensure they continue to operate within their normal specifications. The following instructions must be adhered to
and integrated into your safety program when installing, operating and maintaining Brooks Instrument products.
•To ensure proper performance, use qualified personnel to install, operate, update, program and maintain the product.
•Read all instructions prior to installing, operating and servicing the product. If this instruction manual is not the correct manual, please see back cover
for local sales office contact information. Save this instruction manual for future reference.
WARNING: Do not operate this instrument in excess of the specifications listed in the Instruction and Operation Manual. Failure to heed
this warning can result in serious personal injury and / or damage to the equipment.
If you do not understand any of the instructions, contact your Brooks Instrument representative for clarification.
Follow all warnings, cautions and instructions marked on and supplied with the product.
WARNING: Prior to installation ensure this instrument has the required approval ratings to meet local and national codes. Failure to heed this warning can
result in serious personal injury and / or damage to the equipment.
Install your equipment as specified in the installation instructions of the appropriate instruction manual and per applicable local and national codes.
Connect all products to the proper electrical and pressure sources.
Operation: (1) Slowly initiate flow into the system. Open process valves slowly to avoid flow surges. (2) Check for leaks around the flow meter inlet
and outlet connections. If no leaks are present, bring the system up to the operating pressure.
Please make sure that the process line pressure is removed prior to service. When replacement parts are required, ensure that qualified people use
replacement parts specified by Brooks Instrument. Unauthorized parts and procedures can affect the product's performance and place the safe
operation of your process at risk. Look-alike substitutions may result in fire, electrical hazards or improper operation.
Ensure that all equipment doors are closed and protective covers are in place to prevent electrical shock and personal injury, except when
maintenance is being performed by qualified persons.
WARNING: For liquid flow devices, if the inlet and outlet valves adjacent to the devices are to be closed for any reason, the devices must be completely
drained. Failure to do so may result in thermal expansion of the liquid that can rupture the device and may cause personal injury.
All pressure equipment with an internal pressure greater than 0.5 bar (g) and a size larger than 25mm or 1" (inch) falls under the Pressure Equipment Directive (PED).
The Specifications Section of this manual contains instructions related to the PED directive.
Products described in this manual are in compliance with EN directive 2014/34/EU.
All Brooks Instrument Flowmeters fall under fluid group 1.
Products larger than 25mm or 1" (inch) are in compliance with PED category I, II or III.
Products of 25mm or 1" (inch) or smaller are Sound Engineering Practice (SEP).
The Brooks Instrument (electric/electronic) equipment bearing the CE mark has been successfully tested to the regulations of the Electro Magnetic
Compatibility (EMC directive 2014/30/EU).
Special attention however is required when selecting the signal cable to be used with CE marked equipment.
Quality of the signal cable, cable glands and connectors:
Brooks Instrument supplies high quality cable(s) which meets the specifications for CE certification.
If you provide your own signal cable you should use a cable which is overall completely screened with a 100% shield.
“D” or “Circular” type connectors used should be shielded with a metal shield. If applicable, metal cable glands must be used providing cable screen clamping.
The cable screen should be connected to the metal shell or gland and shielded at both ends over 360 Degrees.
The shield should be terminated to an earth ground.
Card Edge Connectors are standard non-metallic. The cables used must be screened with 100% shield to comply with CE certification.
The shield should be terminated to an earth ground.
For pin configuration : Please refer to the enclosed Instruction Manual.
European Pressure Equipment Directive (PED)
European Electromagnetic Compatibility (EMC)
Essential Instructions
Read before proceeding!
Installation and Operation Manual
X-PR-SolidSense II-PT-eng
Part Number: 541B160AAG
May, 2019
SolidSense II
®
Series
Dear Customer,
We appreciate this opportunity to service your pressure measurement and control requirements with a Brooks
Instrument device. Every day, customers all over the world turn to Brooks Instrument for solutions to their gas
and liquid control applications. Brooks provides an array of ow, pressure and level measurement and control
products for various industries from biopharmaceuticals, oil and gas, fuel cell research and chemicals, to medical
devices, analytical instrumentation, semiconductor manufacturing, and more.
The Brooks product you have just received is of the highest quality available, offering superior performance,
reliability and value to the user. It is designed with the ever changing process conditions, accuracy requirements
and hostile process environments in mind to provide you with a lifetime of dependable service.
We recommend that you read this manual in its entirety. Should you require any additional information concerning
Brooks products and services, please contact your local Brooks Sales and Service Ofce listed on the back cover
of this manual or visit www.BrooksInstrument.com.
Yours sincerely,
Brooks Instrument
Installation and Operation Manual
X-PR-SolidSense II-PT-eng
Part Number: 541B160AAG
May, 2019
SolidSense II
®
Series
Paragraph Page
Number Number
Section 1 Introduction
1-1 Introduction......................................................................................................................................1-1
1-2 Intended Use ...................................................................................................................................1-2
1-3 Notice and Caution Statements.......................................................................................................1-2
1-4 Product Description Code ...............................................................................................................1-2
1-5 SolidSense II Pressure Transducer Specications..........................................................................1-5
Section 2 Installation
2-1 General............................................................................................................................................2-1
2-2 Receipt of Equipment ......................................................................................................................2-1
2-3 Recommended Storage Practice ....................................................................................................2-1
2-4 Return Shipment .............................................................................................................................2-1
2-5 Transit Precautions .........................................................................................................................2-2
2-6 Removal from Storage ....................................................................................................................2-2
2-7 Mechanical Connections .................................................................................................................2-2
2-8 Electrical Connections .....................................................................................................................2-3
2-9 Installation Instructions - Non-Incendive Field Wiring .....................................................................2-6
2-9-1 Non-Incendive Field Wiring 4-20 mA .............................................................................................2-6
2-9-2 Non-Incendive Field Wiring 0-5 Vdc ..............................................................................................2-7
2-10 Zero Adjustment ..............................................................................................................................2-8
2-10-1 .................................................................................................................................................... Zero
Adjustment (SolidSense II Standard Pressure Transducers) .......................................................................2-8
2-10-2 Zero Adjustment (ATEX SolidSense II Standard Pressure Transmitters Only) ..............................2-9
2-10-3 Integrated Display Operation.........................................................................................................2-10
Appendix A: Essential Instructions ............................................................................................................ A-1
Warranty, Local Sales/Service Contact Information ........................................................................Back Cover
Installation and Operation Manual
X-PR-SolidSense II-PT-eng
Part Number: 541B160AAG
May, 2019
SolidSense II
®
Series
Figures
Figure Page
Number Number
1-1 SolidSense II Pressure Transducer Sample Congurations ...........................................................1-1
1-2 Dimensional Drawings - SolidSense II Series, SC: Surface Mount, 1.5” C-Seal ...........................1-7
1-3 Dimensional Drawings - SolidSense II Series, SM: Face Seal, Swivel, Male ................................1-7
1-4 Dimensional Drawings - SolidSense II Series, CS: Surface Mount, 1.125” C-Seal .......................1-8
1-5 Dimensional Drawings - SolidSense II Series, SF: Face Seal, Swivel, VCR, Female ...................1-8
1-6 Dimensional Drawings - SolidSense II Series, CH: 1.5” C-Seal, High Flow....................................1-9
1-7 Dimensional Drawings - SolidSense II Series, 4S: Tube Weld Stub, 1/4” OD ...............................1-9
1-8 Dimensional Drawings - SolidSense II Series, CD: Surface Mount, Longer Gland, 1.125” C-Seal 1-10
1-9 Dimensional Drawings - SolidSense II Series, NT: 1/4” Male NPT ...............................................1-10
1-10 Dimensional Drawings - SolidSense II Series, SM: Face Seal, Swivel Male ................................1-11
1-11 Dimensional Drawings - SolidSense II Series, VS: Face Seal, Fixed Male/Swivel Female ...........1-11
1-12 Dimensional Drawings - SolidSense II Series, 4A: Micro-Fit Tee, 3/8” Branch X 1/4” Run ............1-12
1-13 Dimensional Drawings - SolidSense II Series, VM: Face Seal, Fixed Male ...................................1-12
1-14 Dimensional Drawings - SolidSense II Series, Single End (GID) and Flow Through (GIF)
Integrated Display Models ........................................................................................................1-13
1-15 Dimensional Drawings - SolidSense II ATEX Pressure Transmitter (Option) .................................1-14
2-1 4-20 mA Pinouts ..............................................................................................................................2-4
2-2 Voltage Output Pinouts....................................................................................................................2-4
2-3a 4-20 mA Output Device Wiring to LR056 ........................................................................................2-5
2-3b Integrated Display Electrical Connections .......................................................................................2-5
2-4 Non-Incendive Field Wiring for 4-20 mA..........................................................................................2-6
2-5 Non-Incendive Field Wiring for 0-5 Vdc...........................................................................................2-7
2-6 Location of the Zero Adjustment Screw on the Standard SolidSense II Pressure Transducers .....2-8
2-7 Location of the Zero Adjustment Screw on the ATEX SolidSense II Pressure Transmitters ...........2-9
2-8 Proper Wrench/Leverage Points for SolidSense II Devices ............................................................2-9
2-9 Location of the Zero Adjustment Screw on the Integrated Display SolidSense II Pressure Transmitters
2-10
Table Page
Number Number
1-1 Optional Cables for SolidSense II - Standard..................................................................................1-2
1-2 Product Description Code for SolidSense II - Standard ..................................................................1-3
1-3 Product Description Code for SolidSense II - ATEX ........................................................................1-4
1-4 Specications ..................................................................................................................................1-5
Installation and Operation Manual
X-PR-SolidSense II-PT-eng
Part Number: 541B160AAG
May, 2019
SolidSense II
®
Series
1-1 Introduction
This manual covers the Brooks
®
SolidSense II
®
Series pressure
transducers as shown in Figure 1-1 below. Included herein is general
information, operating specications, installation, removal instructions
and product warranty information.
This manual is organized into the following sections:
Section 1 - Introduction
Section 2 - Installation
Section A - Essential Instructions
Back Cover - Limited Warranty and Contacts
It is recommended that this manual be read in its entirety before
attempting to operate the Brooks SolidSense II Series devices.
Figure 1-1 SolidSense II Pressure Transducer Sample Congurations
Installation and Operation Manual
X-PR-SolidSense II-PT-eng
Part Number: 541B160AAG
May, 2019
SolidSense II
®
Series
1-2 Intended Use
The Brooks SolidSense II Series pressure transducers meet the most rigid
semiconductor and industrial high purity application requirements. With
accuracy of 0.25% of full scale, SolidSense II pressure transducers are used
to provide years of reliable pressure monitoring in a variety of applications.
The SolidSense II Series pressure transducers have one of the smallest
footprints in the industry for quick and easy installation in the tightest areas.
1-3 Notice and Caution Statements
Warning, caution and notice statements are located throughout this manual
in the ANSI format.
A WARNING statement indicates a potentially hazardous situation which, if
not avoided, could result in death or serious injury.
A CAUTION statement indicates a potentially hazardous situation which, if
not avoided, MAY result in minor or moderate injury. It may also be used to
alert against unsafe practices.
A NOTICE statement describes specic information that requires special
attention.
1-4 Product Description Code
The following Product Description Code (PDC) identies the SolidSense II
pressure transducer in various congurations Reference Tables 1-1 thru 1-3.
This code is used to order your SolidSense II pressure transducer. Call your
Brooks Service and Support Representative if you need assistance.
Table 1-1 Optional Cables for SolidSense II - Standard
Installation and Operation Manual
X-PR-SolidSense II-PT-eng
Part Number: 541B160AAG
May, 2019
SolidSense II
®
Series
Table 1-2 Product Description Code for SolidSense II - Standard
SampleSample
SampleSample
Sample
Model CodeModel Code
Model CodeModel Code
Model Code
Code DescriptionCode Description
Code DescriptionCode Description
Code Description
Code OptionCode Option
Code OptionCode Option
Code Option
Option DescriptionOption Description
Option DescriptionOption Description
Option Description
I.I.
I.I.
I. Base Model Code
GFGF
GFGF
GF Pressure Transducer
GIGI
GIGI
GI Pressure Transducer with integrated display
II.II.
II.II.
II. Body Type
DD
DD
D Dead End
FF
FF
F Flow Through
III.III.
III.III.
III. PSI
0000
0000
00 30
0101
0101
01 100
0202
0202
02 250
X2X2
X2X2
X2 235
0505
0505
05 500
1010
1010
10 1000
2525
2525
25 2500
3030
3030
30 3000
6060
6060
60 60
1515
1515
15 1500 Torr
IV.IV.
IV.IV.
IV. Pressure Reference
AA
AA
A Absolute, psi
CC
CC
C Compound, psi
GG
GG
G Gauge, psi
BB
BB
B Absolute, Bar
PP
PP
P Compound, Bar
SS
SS
S Gauge, Bar
TT
TT
T Absolute Torr
V.V.
V.V.
V. Output
33
33
3 0.00 to 10.00 Vdc
44
44
44 to 20 mA
55
55
5 0.05 to 5.05 Vdc
66
66
6 0.2 to 5.2 Vdc
77
77
72 to 10 Vdc
88
88
8 No signal output (GI model with display only)
VI.VI.
VI.VI.
VI. Electrical Connection GFF GFD GIF GID
AA
AA
A4 ft Pigtail with AMP
®
Connector (3-pin) - Current Output Only
xx
BB
BB
B Bendix
®
Connector xx
DD
DD
D 15 Pin HD D-Sub Connector - Voltage Output Only xx
EE
EE
E9 inch Pigtail with 15 Pin (Standard) D-Sub Connector - Voltage Output Only
xxxx
GG
GG
G4 ft Pigtail with AMP
®
Connector (4-pin) - Voltage Output Only
xx
HH
HH
H6 inch Pigtail with Molex
®
Connector
xx
KK
KK
K 9-pin D-Sub - Voltage Output Only xx
LL
LL
L 10 ft (3m) Pigtail
xxxx
MM
MM
M5 inch (0.127m) Pigtail with AMP
®
Connector (4-pin) - Voltage Output Only
xx
NN
NN
N 16.5 ft cable with Bendix
®
Type (Bayonet)
xxxx
PP
PP
P6 ft (2m) Pigtail
xxxx
RR
RR
R8 inch Pigtail with AMP
®
Connector (4-pin)
xx
SS
SS
S 2m (79”) Pigtail with 9-Pin D Connector - Current Output Only xx
VV
VV
V 18 inch Pigtail with 6-pin Molex
®
Connector
xx
WW
WW
W2 inch Pigtail with AMP
®
Connector (4-pin) plus 1” strain relief (+/- 1/8”) at
xx
20° angle from bottom dead center
ZZ
ZZ
Z 36 inch Pigtail ith Bendix
®
Connector (Bayonet)
xxxx
VII.VII.
VII.VII.
VII. Fittings GFF GFD GIF GID
4S*4S*
4S*4S*
4S* Tube Weld Stub 1/4” O.D. x
4T*4T*
4T*4T*
4T* Duncan T, 1/4” Tube Weld Stub x
CDCD
CDCD
CD Surface Mount, 1.125” C-Seal, 0.5” longer gland
xx
CHCH
CHCH
CH Surface Mount, 1.5” C-Seal, High Flow K1H x
CSCS
CSCS
CS Surface Mount, 1.125” C-Seal, Standard
xx
NTNT
NTNT
NT 1/4” NPT x
SCSC
SCSC
SC Surface Mount, 1.5” C-Seal x
SFSF
SFSF
SF Face Seal, swivel female
xxxx
SMSM
SMSM
SM Face Seal, swivel male
xxxx
VMVM
VMVM
VM Face Seal, xed male x x
VSVS
VSVS
VS Face Seal, xed male/swivel female on Duncan
Tx
II
II
I
IIII
IIII
II
IIIIII
IIIIII
III
IVIV
IVIV
IV
VV
VV
V
VIVI
VIVI
VI
VIIVII
VIIVII
VII
GFGF
GFGF
GF
FF
FF
F
0202
0202
02
CC
CC
C
44
44
4
PP
PP
P
SFSF
SFSF
SF
* Tube stubs (4S and 4T) are not suitable for compression joint.
Installation and Operation Manual
X-PR-SolidSense II-PT-eng
Part Number: 541B160AAG
May, 2019
SolidSense II
®
Series
Table 1-3 Product Description Code for SolidSense II - ATEX
Sample Model CodeSample Model Code
Sample Model CodeSample Model Code
Sample Model Code
II
II
I
IIII
IIII
II
IIIIII
IIIIII
III
IVIV
IVIV
IV
VV
VV
V
VIVI
VIVI
VI
VIIVII
VIIVII
VII
VIIIVIII
VIIIVIII
VIII
GFGF
GFGF
GF
FF
FF
F
0202
0202
02
CC
CC
C
44
44
4
PP
PP
P
SFSF
SFSF
SF
AA
AA
A
Code DescriptionCode Description
Code DescriptionCode Description
Code Description
Code OptionCode Option
Code OptionCode Option
Code Option
Option DescriptionOption Description
Option DescriptionOption Description
Option Description
I.I.
I.I.
I. Base Model Code
GFGF
GFGF
GF Pressure Transducer
II.II.
II.II.
II. Body Type
DD
DD
D Dead End
FF
FF
F Flow Through
III.III.
III.III.
III. PSI
0000
0000
00 30
0101
0101
01 100
0202
0202
02 250
0505
0505
05 500
1010
1010
10 1000
2525
2525
25 2500
3030
3030
30 3000
1515
1515
15 1500 Torr
IV.IV.
IV.IV.
IV. Pressure Reference
AA
AA
A Absolute, psi
CC
CC
C Compound, psi
GG
GG
G Gauge, psi
BB
BB
B Absolute, Bar
PP
PP
P Compound, Bar
SS
SS
S Gauge, Bar
TT
TT
T Torr
V.V.
V.V.
V. Output
44
44
44 to 20 mA
55
55
5 0.05 to 5.05 Vdc
VI.VI.
VI.VI.
VI. Electrical Connection
PP
PP
P 2m Pigtail
LL
LL
L 3m Pigtail
EE
EE
E9 inch Pigtail w/15-pin (standard) D-sub Connectors
NN
NN
N 16.5 foot cable with Bendix
®
Type (Bayonet)
VII.VII.
VII.VII.
VII. Fittings
4S4S
4S4S
4S Tube Weld Stub 1/4” O.D. (GFD Only)*
CSCS
CSCS
CS Surface Mount, 1.125” C-Seal, Standard (GFD Only)
CHCH
CHCH
CH Surface Mount, 1.5” C-Seal, High Flow K1H (GFD Only)
SCSC
SCSC
SC Surface Mount, 1.5” C-Seal (GFD Only)
NTNT
NT
NT
NT 1/4” NPT (GFD only)
VMVM
VMVM
VM Face Seal, fixed male (x2 on Duncan T for GFF)
VSVS
VSVS
VS Face Seal, fixed male/swivel female on Duncan T (GFF Only)
SMSM
SMSM
SM Face Seal, swivel male (x2 on Duncan T for GFF)
SFSF
SFSF
SF Face Seal, swivel female (x2 on Duncan T for GFF)
4T4T
4T4T
4T Duncan T, 1/4” Tube Weld Stub (GFF Only)*
VIII.VIII.
VIII.VIII.
VIII.Explosion Proof
AA
AA
A FM and ATEX approved
* Tube stubs (4S and 4T) are not suitable for compression joint.
Installation and Operation Manual
X-PR-SolidSense II-PT-eng
Part Number: 541B160AAG
May, 2019
SolidSense II
®
Series
1-5 SolidSense II Pressure Transducer Specications
Performance Non-Display Version Display Version
Temperature:
Operating: -20
O
F to 180
O
F (-29
O
C to 82
O
C) -20°F to 140°F (-29°C to 60°C)
Storage: -40
O
F to 180
O
F (-40
O
C to 82
O
C) -40°F to 167°F (-40°C to 75°C)
Compensated: -4
O
F to 140
O
F (-20
O
C to 60
O
C) / 68
O
F to 140
O
F (20
O
C to 60
O
C) 0-10 Vdc version
Burst Pressure: 400% full scale
Proof Pressure: 200% full scale up to 2,000 psi, 150% full scale for higher ranges
Accuracy: 0.25% full scale (BFSL)
Response Time: < 5 msec
Zero and Span Temperature
Coecient (each):
>100 PSI Ranges Full Scale: +0.02% full scale/
O
F (-4
O
F to 140
O
F, -20
O
C to 60
O
C)
+0.50% full scale (68
O
F to 140
O
F, 20
O
C to 60
O
C) 0 to 10 Vdc version
<100 PSI Ranges Full Scale: +0.04% full scale/
O
F (-4
O
F to 140
O
F, -20
O
C to 60
O
C)
+1.00% full scale (68
O
F to 140
O
F, 20
O
C to 60
O
C) 0 to 10 Vdc version
Mechanical
Housing: Stainless steel, polymer plastics
Wetted Parts: VIM-VAR 316L stainless steel, SEMI F20
Surface Finish: Compliant with SEMI F19
Cleanliness: Compliant to ASTM F1374-92 (2005)
Internal Volume: 1.79cc
Process Connections: (See Product Congurations for available options)
Approximate Shipping Weight: 0.70 lb. (0.32 kg)
Electrical Non-Display Version Display Version
Supply Current: Max. 10 mA Max. 30 mA
Power Requirements: 10 to 30 Vdc for 4 to 20 mA output 15 to 30 Vdc for 4 to 20 mA output and no signal output
11 to 30 Vdc for 0 to 5 Vdc output 11 to 30 Vdc for 0 to 5 Vdc output
13 to 32 Vdc for 0 to 10 Vdc output 13 to 30 Vdc for 0 to 10 Vdc output
Electrical Connections: Code B Bendix
®
connector
(See Tables 1-1 & 1-2 for Code P Pigtail 6 ft long
full list) Code D 15-pin HD D-sub connector
Code K 9-pin D-sub
Code A 4 ft pigtail with AMP
®
connector (3 pin)
Code G 4 ft pigtail with AMP
®
connector (4 pin)
Code H 6 inch pigtail with Molex
®
connector
Electrical Protection: Reverse polarity for power connections
Table 1-4 Specications
Specications continued on next page.
Installation and Operation Manual
X-PR-SolidSense II-PT-eng
Part Number: 541B160AAG
May, 2019
SolidSense II
®
Series
Optional Display Non-Display Version Display Version
Digits: N/A -xxx to 1xxx
Type: N/A 7 Segment Red LED
Polarity: N/A Automatic (-) Display
Over Pressure Reading Trigger: N/A 110% full scale ± 5% full scale (Display reading: 1---)
Display Accuracy: N/A ±-0.25% of Rdg ± 1 Count for psi
(excluding transducer output) N/A ± - 0.25% of Rdg ± 5 Count for kPa
Character Size: N/A 0.30” height
kPa/psi Switch: N/A Yes
Rotatable: N/A Continuous rotation covering 4 quadrants
Zero Pot: N/A Yes
Zero Pot Adj. Screwdriver: N/A 1-1.2 mm at type
Approvals and Compliance
FM Approval: Non-Incendive for use in Class I, Div II Groups A, B, C and D Hazardous Applications
Excludes 0 to 10 Vdc and 15-pin HD D-Sub connector congurations
EMC: Compliant to EU Directive 2004/108/EC
RoHS: Compliant to EU Directive 2002/95/EC
Table 1-4 Specications (Continued)
Installation and Operation Manual
X-PR-SolidSense II-PT-eng
Part Number: 541B160AAG
May, 2019
SolidSense II
®
Series
Figure 1-3 Dimensional Drawings - SolidSense II Series, SM: Face Seal, Swivel, Male
Figure 1-2 Dimensional Drawings - SolidSense II Series, SC: Surface Mount, 1.5” C-Seal
GFD Congurations
Installation and Operation Manual
X-PR-SolidSense II-PT-eng
Part Number: 541B160AAG
May, 2019
SolidSense II
®
Series
Figure 1-5 Dimensional Drawings - SolidSense II Series, SF: Face Seal, Swivel, VCR, Female
Figure 1-4 Dimensional Drawings - SolidSense II Series, CS: Surface Mount, 1.125” C-Seal
GFD Congurations
Installation and Operation Manual
X-PR-SolidSense II-PT-eng
Part Number: 541B160AAG
May, 2019
SolidSense II
®
Series
Figure 1-7 Dimensional Drawings - SolidSense II Series, 4S: Tube Weld Stub, 1/4” OD
Figure 1-6 Dimensional Drawings - SolidSense II Series, CH: 1.5” C-Seal, High Flow
GFD Congurations
Installation and Operation Manual
X-PR-SolidSense II-PT-eng
Part Number: 541B160AAG
May, 2019
SolidSense II
®
Series
Figure 1-9 Dimensional Drawings - SolidSense II Series, NT: 1/4” Male NPT
Figure 1-8 Dimensional Drawings - SolidSense II Series, CD: Surface Mount, Longer Gland, 1.125” C-Seal
GFD Congurations
Installation and Operation Manual
X-PR-SolidSense II-PT-eng
Part Number: 541B160AAG
May, 2019
SolidSense II
®
Series
Figure 1-11 Dimensional Drawings - SolidSense II Series, VS: Face Seal, Fixed Male/Swivel Female
Figure 1-10 Dimensional Drawings - SolidSense II Series, SM: Face Seal, Swivel Male
GFF Congurations
Installation and Operation Manual
X-PR-SolidSense II-PT-eng
Part Number: 541B160AAG
May, 2019
SolidSense II
®
Series
Figure 1-13 Dimensional Drawings - SolidSense II Series, VM: Face Seal, Fixed Male
Figure 1-12 Dimensional Drawings - SolidSense II Series, 4A: Micro-Fit Tee, 3/8” Branch X 1/4” Run
GFF Congurations
Installation and Operation Manual
X-PR-SolidSense II-PT-eng
Part Number: 541B160AAG
May, 2019
SolidSense II
®
Series
Figure 1-14 Dimensional Drawings - SolidSense II Series, Single End (GID) and Flow Through (GIF) Integrated Display Models
GID & GIF Integrated Display Congurations
Installation and Operation Manual
X-PR-SolidSense II-PT-eng
Part Number: 541B160AAG
May, 2019
SolidSense II
®
Series
Figure 1-15 Dimensional Drawings - SolidSense II ATEX Pressure Transmitter (Option)
For more details on the SolidSense II ATEX compliant pressure
transmitters, visit our website at www.BrooksInstrument.com/Products
for the data sheet: DS-PR-SolidSense II ATEX-PT-eng or contact your
nearest Brooks Customer Service Center for assistance.
Note: Bendix, 15-pin and pigtail available on all ATEX process ttings. Limited examples are shown above.
For all electrical connection and tting options see the Model Code Table.
Additional dimensional drawings are available on request.
Installation and Operation Manual
X-PR-SolidSense II-PT-eng
Part Number: 541B160AAG
May, 2019
SolidSense II
®
Series
2-1 General
This section provides installation instructions for the Brooks
®
SolidSense II
pressure transducers. Refer to Section 1 of this manual for dimensions.
2-2 Receipt of Equipment
When the equipment is received, the outside packing case should be
checked for damage incurred during shipment. If the packing case is
damaged, the local carrier should be notied at once regarding his liability. A
report should be submitted to the nearest Brooks Instrument location listed
on the Global Service Network page on our website: BrooksInstrument.com/
GlobalSupportCenters
Remove the envelope containing the packing list. Carefully remove the
instrument from the packing case. Make sure spare parts are not discarded
with the packing materials. Inspect for damaged or missing parts.
2-3 Recommended Storage Practice
If intermediate or long-term storage of equipment is required, it is
recommended that the equipment be stored in accordance with the following:
a. Within the original shipping container.
b. Ambient temperature 21°C (70°F) nominal, 79°C (175°F) maximum
-29°C (-20°F) minimum.
c. Relative humidity 45% nominal, 60% maximum, 25% minimum.
2-4 Return Shipment
Prior to returning any instrument to the factory for any reason, visit our
website for instructions on how to obtain a Return Materials Authorization
Number (RMA #) and complete a Decontamination Statement to accompany
it: BrooksInstrument.com/Service. All instruments returned to Brooks also
require a Material Safety Data Sheet (MSDS) for the uid(s) used in the
instrument. Failure to provide this information will delay processing of the
instrument.
Instrument must have been purged in accordance with the following:
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50

Brooks GF / GI Istruzioni per l'uso

Tipo
Istruzioni per l'uso