ProLights LUMA1500SH Manuale utente

Categoria
Stroboscopi
Tipo
Manuale utente
USER MANUAL
MANUALE UTENTE
LUMA1500SH
MOVING HEAD
EN - IT
All rights reserved by Music & Lights S.r.l. No part of this instruction manual may be
reproduced in any form or by any means for any commercial use.
In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the
characteristics stated in this instruction manual at any time and without prior notice.
All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it
REV.03-04/18 Firmware v1.1.00
1
LUMA1500 SH
Packing content
LUMA 1500SH
Mount bracket
User manual
TABLE OF CONTENTS
Safety
General instructions
Warnings and installation precautions
1 Introduction
1. 1 Description
1. 2 Technical specifications
1. 3 Operating elements and connections
2 Installation
2. 1 Mounting
3 Functions and settings
3. 1 Operation
3. 2 Basic
3. 3 Using the menu
3. 4 Menu structure
3. 5 Slave Receive mode
3. 6 Operation in automatic mode
3. 7 Scenes Record mode
3. 8 Music mode
3. 9 Microphone Sensitivity
3. 10 Linking
3. 11 DMX addressing
3. 12 DMX mode
3. 13 Connection of the DMX line
3. 14 Construction of the DMX termination
3. 15 DMX control
3. 16 Channel function
3. 17 Color - Gobos wheel
3. 18 Fixture ID and RDM
3. 19 Wireless control settings
3. 20 Fixture settings
3. 21 Advanced
3. 22 Fixture information
4 Maintenance
4. 1 Maintenance and cleaning the unit
4. 2 Fuse replacement
4. 3 Module replacement
4. 4 Trouble shooting
2
2
3
3
6
7
8
8
9
10
12
12
13
14
14
14
15
15
15
16
17
26
27
28
28
28
30
31
32
32
33
35
LUMA1500 SH
2
WARNING! Before carrying out any operations with the unit, carefully read this instruction
manual and keep it with cure for future reference. It contains important information about
the installation, usage and maintenance of the unit.
SAFETY
General instruction
The products referred to in this manual conform to the European Community Directives and are there-
fore marked with
.
The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.
Never make any modifications on the unit not described in this instruction manual, otherwise you will
risk an electric shock.
Connection must be made to a power supply system fitted with efficient earthing (Class I appliance ac-
cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units
from indirect contact and/or shorting to earth by using appropriately sized residual current devices.
The connection to the main network of electric distribution must be carried out by a qualified electrical
installer. Check that the main frequency and voltage correspond to those for which the unit is designed
as given on the electrical data label.
This unit is not for home use, only professional applications.
Never use the fixture under the following conditions:
- in places wet;
- in places subject to vibrations or bumps;
- in places with an ambient temperature of over 45°C.
Make certain that no inflammable liquids, water or metal objects enter the fixture.
Do not dismantle or modify the fixture.
All work must always be carried out by qualified technical personnel. Contact the nearest sales point for
an inspection or contact the manufacturer directly.
If the unit is to be put out of operation definitively, take it to a local recycling
plant for a disposal which is not harmful to the environment.
Warnings and installation precautions
If this device will be operated in any way different to the one described in this manual, it may suffer
damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like
short circuit, burns, electric shock, etc.
Before starting any maintenance work or cleaning the projector, cut off power from the main supply.
Always additionally secure the projector with the safety rope. When carrying out any work, always com-
ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country
in which the fixture’s being used.
For inside use only. Not designed for outside use.
The minimum distance between the fixture and surrounding walls must be more than 50 cm and the
air vents at the housing must not be covered in any case.
Install the fixture in a well ventilated place.
Keep any inflammable material at a safe distance from the fixture.
The maximum temperature that can be reached on the external surface of the fitting, in a thermally
steady state, is high. After power off, please cool down over 15 minutes.
Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent
that their effectiveness is impaired.
The lamp (LED) shall be changed if it has become damaged or thermally deformed.
Never look directly at the light beam. Please note that fast changes in lighting, e. g. flashing light, may
trigger epileptic seizures in photosensitive persons or persons with epilepsy.
This product was designed and built strictly for the use indicated in this documentation. Any other use,
not expressly indicated here, could compromise the good condition/operation of the product and/or
be a source of danger.
We decline any liability deriving from improper use of the product.
3
LUMA1500 SH
- 1 - INTRODUCTION
1.1 DESCRIPTION
LUMA1500SH is a 440 W 6.500 K LED profile light designed to replace the 1.200 W discharge fixture used
in theatres, concerts, events and broadcast. The custom optical system delivers a consistent output with
a flat-field and crisp gobo projection right through the massive 5° to 50° zoom range.
LIGHT SOURCE
Source: 440W high-power white LED
CT: 6.500K
Lux: (5°) 26’533 lx - (50°) 1’535lx @5 m
Source life expectancy: >20.000 h
OPTICS
Zoom: 5° - 50° motorised linear zoom
Lens diameter: 120mm
Lens type: HD anti-reflection lenses with achromatic coating
Focus: motorised with auto-focus
Other: high-quality flat-field projection
COLOUR SYSTEM
Colour mixing: linear CMY
CTC: linear CTO correction 2700 ~ 6000 K
Colour wheel: 7 dichroic filters + open
DYNAMIC EFFECTS
Shutter system: (inc) 4 shutter blades with position and ±30° angle adjustment, ±45° rotation of the
complete framing system
Animation wheel: (opt) animation wheel with CW and CCW rotation
Rotating gobos: 6 rotating gobos + open, interchangeable, indexing
Gobo size: outer: 22,8 mm - image: 20 mm - thickness: 1,1 mm
Fixed gobos: 7 fixed gobos + open, interchangeable
Gobo size: gobo Ø 27 mm - img vØ 20 mm - 1,1 mm
Circular prism: 3f with bi-directional rotation, indexing
Frost: linear 0 - 100% frost filter
Iris: 5 - 100% motorised linear iris
BODY
Pan angle: 630° - 540°
Tilt angle: 267°
Pan/Tilt resolution: 8 / 16 bit
Feedback: automatic repositioning after accidental movement
Body: aluminium structure with hi-resistance polycarbonate cover
Body colour: black
CONTROL
Protocols: DMX512, RDM, W-DMX
DMX channels: 28 / 30 / 37 / 38channel
LUMA1500 SH
4
W-DMX: included, wireless solution receiver
RDM: RDM ready for fixture remote monitor and settings
Display: LCD high resolution colour display
Firmware upgrade: yes, via USB - DMX interface (UPBOX2) not included
Hibernation: power safe mode when lost DMX
ELECTRONICS
Dimmer: linear 0 ~ 100% electronic dimmer
Strobe / shutter: 1 - 28 Hz, electronic
Battery backup: battery backup for user operation without connecting to the main power
Operating temperature: -10° ~ +45°
ELECTRICAL
Power supply: 100-240 V – 50/60 Hz
Power consumption (at 230V): 650W
Power consumption (at 120V): 650W
Power factor: 0,98
PHYSICAL
Cooling: combination of heat pipe cooling system and low noise fan
Sospension and fixing: any position with quick-lock omega brackets
Pan / tilt lock: pan / tilt locking for transportation and maintenance
Signal connection: Amphenol XLR 3p + 5p IN/OUT connectors
Power connection: Neutrik powerCON TRUE1 IN connector
IP rating: 20
Dimensions (WxHxD): 428x757x291mm
Weight: 31kg
Fig.1
428mm
16,85in
235mm
9,25in
758mm
29,84in
Technical drawing
5
LUMA1500 SH
1
2
3
5
6
7
8
9
10
11
12
14
13
A
B
4
1.3 OPERATING ELEMENTS AND CONNECTIONS
Fig.2
1. MOVING HEAD
2. ROTARY ARM
3. TILT Mechanism Lock and Release
4. PAN Mechanism Lock and Release
5. HANDLE
6. LED INDICATOR "WDMX"
7. MICROPHONE
8. CONTROL PANEL with LCD display
and 5 button used to access
the control panel functions and
manage them.
9. DMX OUT ( 3-pole XLR):
1 = ground, 2 = DMX -, 3 = DMX +
10. DMX IN (3-pole XLR):
1 = ground, 2 = DMX -, 3 = DMX +
11. DMX OUT (5-pole XLR):
1 = ground, 2 = DMX-, 3 = DMX+,
4 N/C, 5 N/C
12. DMX IN (5-pole XLR):
1 = ground, 2 = DMX-, 3 = DMX+,
4 N/C, 5 N/C
13. MAIN FUSE HOLDER: replace a
burnt-out fuse by one of the same
type only.
14. POWER IN (PowerCON TRUE
IN): for connection to a socket
(100-240V~/50-60Hz) via the
supplied mains cable.
View A
View B
LUMA1500 SH
6
- 2 - INSTALLATION
2.1 MOUNTING
The LUMA 1500SH may be set up on a solid and even surface. By means of the fixing facilities of the base-
plate, the unit can also be mounted upside down to a cross arm. The base plate is shown in fig.3. For fixing,
stable mounting clips are required. According to the figure, the bolts of the brackets are placed into the
openings provided in the base plate and turned clockwise until they lock (to the stop). Always ensure that
the unit is firmly fixed to avoid vibration and slipping while operating. The mounting place must be of
sufficient stability and be able to support a weight of 10 times of the units weight. When carrying out any
installation, always comply scrupulously with all the regulations (particularly regarding safety) currently
in force in the country in which the fixture’s being used. Always additionally secure the projector with the
safety rope from falling down. For this purpose, fasten the safety rope at a suitable position so that the
maximum fall of the projector will be 20 cm.
Fig.3
CLAMP
SAFETY ROPE
OMEGA
7
LUMA1500 SH
- 3 - FUNCTIONS AND SETTINGS
3.1 OPERATION
Connect the supplied main cable to a socket (100-240V~/50-60Hz). The unit will run built-in program to re-
set all motors to their home position. Shortly after that the LUMA 1500SH is ready for operation. To switch
off, disconnect the mains plug from the socket. For a more convenient operation it is recommended to
connect the unit to a socket which can be switched on and off via light switch.
3.2 BASIC
The control panel of LUMA 1500SH has a display and 5 buttons for the complete programming and man-
agement of the projector menu (fig.4).
Fig.4 - Functions of the buttons and display icons
UP
DOWN LEFT RIGHT ENTER BATTERY
Increases the value
displayed or passes
to the previous item
in a menu
Decreases the value
displayed or passes
to the next item in
the menu
Return to the top
level
Commute from
units, tens, hundred
in the menu
Confirms the
displayed value,
or activates the
displayed function,
or enters the
successive menu
Used to activate the
backup battery. It
allows to switching
display interface
without main power
CONNECT SETUP ADVANCED INFORMATION STAND ALONE
Battery
SH
LUMA1500 SH
8
Fig.5 - Reversal of the display
3.3 USING THE MENU
1. Press the ENTER button to access the main menu.
2. Use the UP/DOWN button to select the menu to be used:
Connect;
Setup;
Advanced;
Information;
Stand alone;
3. Press ENTER to display the first item in the selected menu.
4. Use the UP/DOWN button to select the menu items.
NOTE - The display can be in one of two conditions: rest status and setting status. When it is in the rest sta-
tus, the display shows the projector’s DMX address. During menu setting status, after a wait time without
any key having been pressed, the display automatically returns to rest status.
It should be noted than when this condition occurs, any possible value that has been modified but not yet
confirmed with the ENTER button will be cancelled.
Reversal of the display
To activate this function, hold simultaneously for 3 seconds UP and DOWN buttons while the display is in
the rest mode. This status will be memorised and maintained even for the next time it will be switched on.
To return to the initial state, repeat the operation all over again.
9
LUMA1500 SH
MENU
1 CONNECT
ð
Address
ð
DMX
ð
Value (1-512)
W-DMX
ð
Value (1-512)
DMX Mode
ð
Mode
ð
Standard/Extended/ Basic-8bit/Basic-16bit/User
Edit User
ð
Max Channel/Control/Pan/Pan Fine/Tilt/...
Wireless
ð
DMX Out
ð
ON/OFF
Reset Connect
ð
YES/NO
RDM ID
ð
Name
ð
Fixture ID Name
Mode
ð
Mode1 / Mode2
Password
ð
050 (unlocks the following settings)
PID Code
ð
00001
2 SET UP
ð
Temperature
ð
Temperature C/F
ð
Celsius/Fahrenheit
Max Temperature
ð
Value (60°-139° C)
Movement
ð
Pan Reverse
ð
YES/NO
Tilt Reverse
ð
YES/NO
Pan Degree
ð
540/630
Pan/Tilt Feedbacks
ð
YES/NO
Pan/Tilt Mode
ð
Standard/Smooth
Screen
ð
Backlight
ð
Always On/Min (01-99)
Flip Display
ð
YES/NO
Display Bright
ð
Value (00-31)
Key Lock
ð
ON/OFF
Language
ð
EN/FR/SP...
Fixture
ð
Theater mode
ð
ON/OFF
Fans Mode
ð
Auto Speed/High Speed
No Signal
ð
Close/Hold/Auto/Music
Hibernation
ð
Disable/Min (01-99)
Adjust
ð
Control, Pan, Pan Fine, Tilt,
Tilt Fine, Pan&Tilt Speed,
Pan&Tilt Fun, Shutter Fun,
Shutter, Dimmer, Color1 Fun,
Color1, Cyan, Magenta, Yel-
low, CTO, Gobo1 Fun, Gobo1,
Gobo1 Rot. Fun, Gobo1
Rot., Gobo2 Fun, Gobo2,
Prism, Prism Rot., Focus Fun,
Focus, Zoom, Iris Fun, Iris
Fun, Animation&Blade1A,
Animation&Blade1B,
Blade2A, Blade2B, Blade3A,
Blade3B, Blade4A, Blade4B
ð
Value (000-255) for each function
3.4 MENU STRUCTURE
LUMA1500 SH
10
3 ADVANCED
ð
Reset
ð
All
Pan & Tilt
Colors
Gobos
Others
Calibration
ð
Password
ð
050 (unlocks the following settings)
Pan
ð
Value (-128-127)
Tilt
ð
Value (-128-127)
Color1
ð
Value (-128-127)
Gobo1
ð
Value (-128-127)
Prism
ð
Value (-128-127)
Focus
ð
Value (-128-127)
Reload Default
ð
Basic Reload
ð
ON/OFF
Program Reload
ð
ON/OFF
Password
ð
050 (unlocks the following settings)
Private Reload
ð
ON/OFF
All Reload
ð
ON/OFF
4 INFORMATION
ð
Time I nfo.
Temperature
Fans Speed
Channel Value
Error Message
Fixture Model
Software Ver.
5 STAND ALONE
ð
Play
ð
DMX Receive
Slave Receive
ð
Part 1-2-3 Receive
Sequence
ð
Alone/Master
Music
ð
Alone/Master
Mic Sens.
ð
Value (00-99%)
Select Chase
ð
Chase Part 1
ð
Chase 1 - Chase 8
Chase Part 2 Chase 1 - Chase 8
Chase Part 3
ð
Chase 1 - Chase 8
Edit Chases
ð
Edit Chase 1
ð
Chase Test/ Step 1 - Step 64
Edit Chase ... Chase Test/ Step 1 - Step 64
11
LUMA1500 SH
Edit Chase 8
ð
Chase Test/ Step 1 - Step 64
Edit Scenes
ð
Edit Scenes 001
ð
Pan/Tilt/CMY, Gobo1...
Edit Scenes ...
ð
Pan/Tilt/CMY, Gobo1...
Edit Scenes 250
ð
Pan/Tilt/CMY, Gobo1...
Scenes Record
ð
Sc XX - Sc XX
3.5 SLAVE RECEIVE MODE
This mode will allow you to link up the units together without a controller. Choose a unit to function as the
Master. The unit must be the first unit in line; other units will work as slave with the same effect.
A Master unit can send up to 3 different data groups to the Slave units, i.e. a Master unit can start 3 differ-
ent Slave units, which run 3 different programs. The Master unit sends the 3 program parts in a continuous
loop.
The Slave unit receives data from the Master unit according to the group which the Slave unit was as-
signed to.
For example, if a slave device is set to Receive Part 1, the Master unit Slave unit will send the automated Chase
Part 1; if set to Receive Part 2, the Chase Part 2 Slave units will receive from the Master.
To set the drive as a slave, proceed as follows:
Press the ENTER button to access the main menu.
Press the UP/DOWN button to scroll the menu, select the Stand Alone icon, then press the ENTER button
to enter the next menu.
Press the UP/DOWN button to scroll through the menu, and then select Play and press the ENTER
button to enter the next menu.
Press the UP/DOWN button to scroll through the menu, and select Slave Receive and press ENTER to
confirm.
Press the UP/DOWN button to select the different modes of operation Part 1 Receive/Receive Part 2/Part 3
Receive, and then press the ENTER button to confirm your choice.
Press the LEFT button repeatedly to exit the menu and save changes.
Select the desired program on the master unit (described in section 3.6).
Use the DMX connectors of the LUMA 1500SH and an XLR cable to form a chain of units. Under certain
conditions and lengths you want to make a termination as shown on page 18.
3.6 OPERATIONS IN AUTOMATIC MODE
The unit independently runs through its show. Before you send an automatic program you need to set the
drive as Master/Alone:
Press the ENTER button to access the main menu.
Press the UP/DOWN button to scroll the menu, select the Stand Alone icon, then press the ENTER button
to enter the next menu.
Press the UP/DOWN button to scroll through the menu, select Play and press the ENTER button to enter
the next menu.
Press the UP/DOWN button to scroll through the menu, select Sequence and press ENTER to confirm
your choice.
Press the UP/DOWN button to select the mode of operation:
- Master, if the unit is connected in series with other units and it acts as the Master;
LUMA1500 SH
12
- Alone, if the unit is not connected to other units.
Press the ENTER button to confirm your choice.
Press the LEFT button repeatedly to exit the menu and save changes.
The unit will go into automatic mode by executing the program automatically.
Select Chase
The function Select Chase lets you choose the automatic program to actually run.
Press the ENTER button to access the main menu.
Press the UP/DOWN button to scroll the menu, select the Stand Alone icon, then press the ENTER button
to enter the next menu.
Press the UP/DOWN button to scroll through the menu, select Select Chase and press the ENTER button
to enter the next menu.
Press the UP/DOWN button to scroll through the menu, then select Chase Part 1/Chase Part 2/Chase Part 3
and press ENTER to confirm.
Press the UP/DOWN button to select Chase1-Chase8, and press the ENTER button to confirm.
Press the LEFT button repeatedly to exit the menu and save changes.
Edit Chases
The function Edit Chases allows you to create automatic pre-programmed show.
The automatic programs Chase Part1/2/3 are each divided into Chase1-Chase8. Each Chase can be composed
of 1-64 step that can be configured through the following procedure:
Press the ENTER button to access the main menu.
Press the UP/DOWN button to scroll the menu, select the Stand Alone icon, then press the ENTER button
to enter the next menu.
Press the UP/DOWN button to scroll through the menu, select Edit Chases and press the ENTER button
to enter the next menu.
Press the UP/DOWN button to scroll through the menu, select Edit Chase 1 - Edit Chase 8, then press the
ENTER button to confirm.
Press the UP/DOWN button to select the Step 01 - Step 64, and press ENTER to confirm.
Press the UP/DOWN button to select the Scene you want to set for the Step chosen, and then press
ENTER to confirm. Press the LEFT button repeatedly to exit the menu and save changes.
Edit Scenes
The function Edit Scenes allows you to create individual scenes to be included in the Chase Step.
Press the ENTER button to access the main menu.
Press the UP/DOWN button to scroll the menu, select the Stand Alone icon, then press the ENTER button
to enter the next menu.
Press the UP/DOWN button to scroll through the menu, select Edit Scenes and press the ENTER button
to enter the next menu.
Press the UP/DOWN button to scroll through the menu, select Edit Scene 001 - Edit Scene 250, then press the
ENTER button to confirm.
Press the UP/DOWN button to select the desired function you want to edit (Control, Pan, Tilt, etc..), Then
press the ENTER button to confirm.
Press the UP/DOWN button to change the value of the function, then press the ENTER button to
confirm. Press the LEFT button repeatedly to exit the menu and save changes.
3.7 SCENES RECORD MODE
LUMA 1500SH is equipped with a built-in DMX recorder by which you can transmit the programmed
scenes from your DMX-controller to the device. Proceed as follows to store the sequence of scenes in the
13
LUMA1500 SH
unit.
Press the ENTER button to access the main menu.
Press the UP/DOWN button to scroll through the menu, select the Stand Alone icon, then press the ENTER
button to enter the next menu.
Press the UP/DOWN button to scroll through the menu, select Scenes Record and press the ENTER button
to enter the next menu.
Press the UP/DOWN button to adjust the scene at the beginning and end to be inserted in the auto-
matic program, then press the ENTER button to confirm.
Press the LEFT button repeatedly to exit the menu and save changes.
When recalling scenes from the controller will automatically be transmitted to the device.
3.8 MUSIC MODE
In music mode, via its integrated microphone, the unit can be controlled by music with a clear rhythm in
the bass range. If the music control should not work optimally, increase the volume or reduce the distance
between the sound source and the light effect unit or alternatively increase the sensitivity of the micro-
phone.
Press the ENTER button to access the main menu.
Press the UP/DOWN button to scroll the menu, select the Stand Alone icon, then press the ENTER button
to enter the next menu.
Press the UP/DOWN button to scroll through the menu, select Play and press the ENTER button to enter
the next menu.
Press the UP/DOWN button to scroll through the menu, select Music and press ENTER to confirm.
Press the UP/DOWN button to select the mode of operation:
- Master, if the mobile head is connected in series to other units, and it performs the Master function;
- Alone, if the fixture is not connected to other units.
Press the ENTER button to confirm your choice.
Press the LEFT button repeatedly to exit the menu and save changes.
The unit will go into music mode by executing an automatic program to the rhythm of music.
3.9 MICROPHONE SENSITIVITY
Select this function to set the value of the sensitivity of the microphone for use with a music control:
Press the ENTER button to access the main menu.
Press the UP/DOWN button to scroll the menu, select the Stand Alone icon, then press the ENTER button
to enter the next menu.
Press the UP/DOWN button to scroll through the menu, select Play, and press the ENTER button to enter
the next menu.
Press the UP/DOWN button to scroll through the menu, then select Mic Sens. and press ENTER to confirm.
Press the UP/DOWN button to adjust the level of sensitivity of the microphone, and then press the
ENTER button to confirm your choice.
Press the LEFT button repeatedly to exit the menu and save changes.
3.10 LINKING
Several units may be interconnected in order to control all further slave units to the same effect of the
master unit.
1. Connect the DMX OUT of the master unit via 3/5-pole XLR cable to the DMX IN of the first slave unit.
2. Connect the DMX OUT of the first slave unit to the DMX IN of the second slave unit, etc. until all units
are connected in a chain.
LUMA1500 SH
14
3.11 DMX ADDRESSING
To enter the DMX mode, follow these steps:
Press the ENTER button to access the main menu.
Press the UP/DOWN button to scroll the menu, select the Connect icon, then press the ENTER button to
enter the next menu.
Press the UP/DOWN button to scroll through the menu, select the Address and press the ENTER key.
Press the arrow keys to select the desired value (001-512).
Press the ENTER key to confirm the setting.
Press the LEFT button repeatedly to exit the menu and save changes.
3.12 DMX MODE
The LUMA 1500SH has 4 DMX channel configurations which can be accessed from the control panel.
Press the ENTER button to access the main menu.
Press the UP/DOWN button to scroll the menu, select the Connect icon, then press the ENTER button to
enter the next menu.
Press the UP/DOWN button to scroll through the menu, select DMX Mode and press the ENTER button to
enter the next menu.
Press the UP/DOWN button to scroll through the menu, select Mode and press ENTER to confirm your
choice.
Use the UP/DOWN button to select the desired DMX channel configuration (Standard, Extended, Basic-8bit,
Basic-16bit, User), then press the ENTER button to confirm your choice.
Press the LEFT button repeatedly to exit the menu and save changes.
The tables on page 17 show the mode of operation and their values DMX.
The unit is equipped with 3/5-pole XLR connections.
Edit User
The Edit User, in the same menu, allows you to create a profile of personalized functions. You can change
the parameters of the various functions (Control, Pan, Tilt, etc.). Once you’ve created your custom profile,
you can use it by selecting the USER mode as described above.
Fig.7
3.13 CONNECTION OF THE DMX LINE
DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120Ω imped-
ance and low capacity.
The following diagram shows the connection mode:
DMX - OUTPUT
XLR socket
DMX - INPUT
XLR plug
Pin1 : GND - Shield
Pin2 : - Negative
Pin3 : + Positive
Pin4 : N/C
Pin5 : N/C
15
LUMA1500 SH
Fig.8
ATTENTION
The screened parts of the cable (sleeve) must never be connected to the systems earth, as this would
cause faulty fixture and controller operation.
Over long runs can be necessary to insert a DMX level matching amplifier.
For those connections the use of balanced microphone cable is not recommended because it cannot
transmit control DMX data reliably.
Connect the controller DMX input to the DMX output of the first unit.
Connect the DMX output to the DMX input of the following unit. Connect again the output to the input
of the following unit until all the units are connected in chain.
When the signal cable has to run longer distance is recommended to insert a DMX termination on the
last unit.
3.14 CONSTRUCTION OF THE DMX TERMINATION
The termination avoids the risk of DMX 512 signals being reflected back along the cable when they reach-
es the end of the line: under certain conditions and with certain cable lengths, this could cause them to
cancel the original signals.
The termination is prepared by soldering a 120Ω 1/4 W resistor between pins 2 and 3 of the 5-pin male XLR
connector, as shown in figure.
Example:
3 pin XLR connector
LUMA1500 SH
16
3.15 DMX CONTROL
BAS-8 BAS-16 STD EXT
FUNCTION
DMX
Value
28 Ch 30 Ch 37 Ch 38 Ch
1 1 1 1
PAN
0~100% 000 - 255
2 2 2
PAN FINE
0~100% 000 - 255
2 3 3 3
TILT
0~100% 000 - 255
4 4 4
TILT FINE
0~100% 000 - 255
3 5 5 5
P/T SPEED
Fastest to slowest 000 - 255
6
P/T FUNCTION
Normal
Movement with Blackout
TBD (not used)
000 - 015
016 - 031
032 - 255
6 7
SHUTTER FUNCTION
Normal Shutter Functions
Pulse-effect Forward
Pulse-effect Reverse
Random strobe
TBD (not used)
000 - 015
016 - 031
032 - 047
048 - 063
064 - 255
7 8
SHUTTER
Normal Shutter Functions
Close
Strobe Rate (slow to fast)
Open
Pulse-effect Forward
Close
Strobe Rate (slow to fast)
Open
Pulse-effect Reverse
Close
Strobe Rate (slow to fast)
Open
Random Strobe
Close
Strobe Rate (slow to fast)
Open
000 - 031
032 - 223
224 - 255
000 - 031
032 - 223
224 - 255
000 - 031
032 - 223
224 - 255
000 - 031
032 - 223
224 - 255
4 6
SHUTTER
Shutter closed
No function (shutter open)
Strobe effect slow to fast
000 - 031
032 - 063
064 - 095
17
LUMA1500 SH
BAS-8 BAS-16 STD EXT
FUNCTION
DMX
Value
28 Ch 30 Ch 37 Ch 38 Ch
4 6
No function (shutter open)
Pulse-effect in sequences
No function (shutter open)
Random strobe effect slow to fast
No function (shutter open)
096 - 127
128 - 159
160 - 191
192 - 223
224 - 255
5 7 8 9
DIMMER
Dimmer (0% to 100%) 000 - 255
9 10
COLOR FUNCTION
Indexed
Indexed with Blackout
Forward Spin
Reverse Spin
Continuous
Color Bounce (from slow to fast)
TBD (not used)
000 - 015
016 - 031
032 - 047
048 - 063
064 - 079
080 - 111
112 - 255
10 11
COLOR
Indexed - Indexed w. Blackout - Bounce
1 - Open
2 - Open / Dark Red
3 - Dark Red
4 - Dark Red / Pink
5 - Pink
6 - Pink / Amber
7 - Amber
8 - Amber / Light Green
9 - Light Green
10 - Light Green / Dark Blue
11 - Dark Blue
12 - Dark Blue / Aquamarine
13 - Aquamarine
14 - Aquamarine / Congo Blue
15 - Congo Blue
16 - Congo Blue / Open
Forward Spin
Stop to fastest
Reverse Spin
Stop to fastest
Continuous
Positioning from 0 -360 degrees
000 - 015
016 - 031
032 - 047
048 - 063
064 - 079
080 - 095
096 - 111
112 - 127
126 - 143
144 - 159
160 - 175
176 - 191
192 - 207
208 - 223
224 - 239
240 - 255
000 - 255
000 - 255
000 - 255
LUMA1500 SH
18
BAS-8 BAS-16 STD EXT
FUNCTION
DMX
Value
28 Ch 30 Ch 37 Ch 38 Ch
6 8
COLOR
Indexed
1 - Open
2 - Open / Dark Red
3 - Dark Red
4 - Dark Red / Pink
5 - Pink
6 - Pink / Amber
7 - Amber
8 - Amber / Light Green
9 - Light Green
10 - Light Green / Dark Blue
11 - Dark Blue
12 - Dark Blue / Aquamarine
13 - Aquamarine
14 - Aquamarine / Congo Blue
15 - Congo Blue
16 - Congo Blue / Open
Indexed with Blackout
1 - Open
2 - Open / Dark Red
3 - Dark Red
4 - Dark Red / Pink
5 - Pink
6 - Pink / Amber
7 - Amber
8 - Amber / Light Green
9 - Light Green
10 - Light Green / Dark Blue
11 - Dark Blue
12 - Dark Blue / Aquamarine
13 - Aquamarine
14 - Aquamarine / Congo Blue
15 - Congo Blue
16 - Congo Blue / Open
Indexed with Bounce
1 - Open
2 - Open/ Dark Red
3 - Dark Red
4 - Dark Red / Pink
5 - Pink
6 - Pink / Amber
7 - Amber
8 - Amber / Light Green
9 - Light Green
000 - 001
002 - 003
004 - 005
006 - 007
008 - 009
010 - 011
012 - 013
014 - 015
016 - 017
018 - 019
020 - 021
022 - 023
024 - 025
026 - 027
028 - 029
030 - 031
032 - 033
034 - 035
036 - 037
038 - 039
040 - 041
041 - 043
044 - 045
046 - 047
048 - 049
050 - 051
052 - 053
054 - 055
056 - 057
058 - 059
060 - 061
062 - 063
064 - 073
074 - 083
084 - 093
094 - 103
104 - 113
114 - 123
124 - 133
134 - 143
144 - 153
1 / 1

ProLights LUMA1500SH Manuale utente

Categoria
Stroboscopi
Tipo
Manuale utente

in altre lingue