Hotpoint ARSF 85 (EU) Guida utente

Categoria
Lavatrici
Tipo
Guida utente
GB
1
English,1
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Description of the washing machine
and starting a wash cycle, 4-5
Control panel
Indicator lights
Starting a wash cycle
Wash cycles, 6
Table of wash cycles
Personalisation, 7
Setting the temperature
Setting the spin speed
Functions
Detergents and laundry, 8
Detergent dispenser drawer
Bleach cycle
Preparing the laundry
Garments requiring special care
Load balancing system
Precautions and tips, 9
General safety
Disposal
Opening the porthole door manually
Care and maintenance, 10
Cutting off the water or electricity supply
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Troubleshooting, 11
Service, 12
GB
ARSF 85
Instructions for use
WASHING MACHINE
Polski,13
PL
ÐÓÑÑÊÈÉ, 25
CIS
2
GB
A
Installation
This instruction manual should be kept in a safe
place for future reference. If the washing machine is
sold, transferred or moved, make sure that the
instruction manual remains with the machine so that
the new owner is able to familiarise himself/herself
with its operation and features.
Read these instructions carefully: they contain vital
information relating to the safe installation and
operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its packaging.
2. Make sure that the washing machine has not been
damaged during the transportation process. If it has
been damaged, contact the retailer and do not
proceed any further with the installation process.
3. Remove the 4
protective screws (used
during transportation) and
the rubber washer with
the corresponding
spacer, located on the
rear part of the appliance
(see figure).
4. Close off the holes using the plastic plugs provided.
5. Keep all the parts in a safe place: you will need
them again if the washing machine needs to be
moved to another location.
Packaging materials should not be used as toys for
children.
Levelling
1. Install the washing machine on a flat sturdy floor,
without resting it up against walls, furniture cabinets
or anything else.
2. If the floor is not
perfectly level, compen-
sate for any unevenness
by tightening or loosening
the adjustable front feet
(see figure); the angle of
inclination, measured in
relation to the worktop,
must not exceed 2°.
Levelling the machine correctly will provide it with
stability, help to avoid vibrations and excessive noise
and prevent it from shifting while it is operating. If it is
placed on carpet or a rug, adjust the feet in such a
way as to allow a sufficient ventilation space
underneath the washing machine.
Connecting the electricity and water
supplies
Connecting the water inlet hose
1. Insert seal A into the
end of the inlet hose and
screw the latter onto a
cold water tap with a 3/4
gas threaded opening
(see figure).
Before performing the
connection, allow the
water to run freely until it
is perfectly clear.
2. Connect the inlet hose
to the washing machine
by screwing it onto the
corresponding water inlet
of the appliance, which is
situated on the top right-
hand side of the rear part
of the appliance (see
figure).
3. Make sure that the hose is not folded over or bent.
The water pressure at the tap must fall within the
values indicated in the Technical details table (see
next page).
If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
Never use second-hand hoses.
Use the ones supplied with the machine.
GB
3
Technical data
Model
ARSF 85
Dimensions
width 59.5 cm
height 85 cm
depth 40 cm
Capacity
from 1 to 5 kg
Electrical
connections
please refer to the technical data
plate fixed to the machine
Water connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 40 litres
Spin speed
up to 800 rotations per minute
Energy rated
programmes
according to
regulation
EN 60456
programme 6; temperature 60°C;
using a load of 5 kg.
This appliance conforms to the
following EC Directives:
- 72/23/EEC dated 19/02/73 (Low
Voltage) and subsequent modifications
- 89/336/EEC dated 03/05/89
(Electromagnetic Compatibility) and
subsequent modifications
- 2002/96/EC
65 - 100 cm
Connecting the drain hose
Connect the drain hose,
without bending it, to a
drainage duct or a wall
drain located at a height
between 65 and 100 cm
from the floor;
alternatively, rest it on
the side of a washbasin
or bathtub, fastening the
duct supplied to the tap
(see figure). The free end
of the hose should not
be underwater.
We advise against the use of hose extensions; if it is
absolutely necessary, the extension must have the
same diameter as the original hose and must not
exceed 150 cm in length.
Electrical connections
Before plugging the appliance into the electricity
socket, make sure that:
the socket is earthed and complies with all
applicable laws;
the socket is able to withstand the maximum power
load of the appliance as indicated in the Technical
data table (see opposite);
the power supply voltage falls within the values
indicated in the Technical data table (see opposite);
the socket is compatible with the plug of the
washing machine. If this is not the case, replace
the socket or the plug.
The washing machine must not be installed
outdoors, even in covered areas. It is extremely
dangerous to leave the appliance exposed to rain,
storms and other weather conditions.
When the washing machine has been installed, the
electricity socket must be within easy reach.
Do not use extension cords or multiple sockets.
The cable should not be bent or compressed.
The power supply cable must only be replaced by
authorised technicians.
Warning! The company shall not be held responsible
in the event that these regulations are not respected.
The first wash cycle
Once the appliance has been installed, and before
you use it for the first time, run a wash cycle with
detergent and no laundry, using the wash cycle 1.
4
GB
Detergent dispenser drawer: used to dispense
detergents and washing additives (see Detergents
and laundry).
There is a key which provides a summary of the
available wash cycles inside the detergent dispenser
drawer; this may be consulted at any time.
ON/OFF button with indicator light: switches the
machine on and off.
If the indicator light is illuminated, this indicates that
the machine is switched on.
WASH CYCLE knob: programmes the wash cycles.
During the wash cycle, the knob does not move.
SPIN SPEED button: sets the spin speed or exclude
the spin cycle completely (see Personalisation).
TEMPERATURE button: sets the temperature or the
cold wash cycle (see Personalisation).
DISPLAY: indicates the time remaining for the
selected wash cycle and, if a delayed start has been
programmed, the time remaining until the start of the
wash cycle.
CONTROL PANEL LOCK button with indicator light:
activates or deactivates the control panel lock.
FUNCTION buttons with indicator light: used to
select the available functions. The indicator light
corresponding to the selected function will remain lit.
WASH CYCLE PROGRESS
indicator light
s: used to
monitor the progress of the wash cycle.
The illuminated indicator light shows which phase is in
progress.
DOOR LOCKED indicator light: indicates whether
the door may be opened or not (see next page).
START/PAUSE button with indicator light: starts or
temporarily interrupts the wash cycles.
N.B. To pause the wash cycle in progress, press this
button; the corresponding indicator light will flash
orange, while the indicator light for the current wash
cycle phase will remain lit in a fixed manner. If the
DOOR LOCKED
indicator light is switched off, the
door may be opened.
To start the wash cycle from the point at which it was
interrupted, press this button again.
Description of the washing machine
and starting a wash cycle
DOOR
LOCKED
indicator light
START/PAUSE
button with indicator
light
Control panel
WASH CYCLE PROGRESS
indicator lights
FUNCTION
buttons with
indicator lights
Detergent dispenser drawer
WASH CYCLE
knob
DISPLAY
ON/OFF
button with indicator
light
TEMPERATURE
button
SPIN SPEED
button
CONTROL PANEL LOCK
button with indicator light
GB
5
Indicator lights
The indicator lights provide important information.
This is what they can tell you:
Wash cycle phase indicator lights
As the WASH CYCLE knob is rotated, the indicator
lights illuminate, indicating the stages which will be
performed by the machine in accordance with the
selected wash cycle.
Once the desired wash cycle has been selected and
has begun, the indicator lights switch on one by one
to indicate which phase of the cycle is currently in
progress.
Function buttons and corresponding indicator
lights
When a function is selected, the corresponding
indicator light will illuminate.
If the selected function is not compatible with the
programmed wash cycle, the corresponding indicator
light will flash, a sound signal will be emitted and the
function will not be activated.
If a function which is incompatible with another
function selected previously, only the most recent
selection will remain active.
Temperature indicator light
When a temperature value is selected, the
corresponding indicator light will illuminate.
Spin indicator light
When a spin value is selected, the corresponding
indicator light will illuminate.
Control panel lock indicator light
To activate the control panel lock, press and hold the
button for approximately 2 seconds. When the
indicator light is illuminated, the control panel is
locked. This means it is possible to prevent wash
cycles from being modified accidentally, especially
where there are children in the home.
To deactivate the control panel lock, press and hold
the button for approximately 2 seconds.
Door locked indicator light
If this indicator light is on, the appliance door is locked
to prevent it from being opened accidentally; to avoid
any damage, wait for the indicator light to switch off
before you open the appliance door.
N.B. If the DELAY TIMER function is activated, the door
cannot be opened; pause the machine by pressing the
START/PAUSE button if you wish to open it.
If the START/PAUSE indicator light (orange) flashes
rapidly at the same time as the function indicator
light, this indicates a problem has occurred (see
Troubleshooting).
Starting a wash cycle
1. Switch the washing machine on by pressing the ON/OFF button. All indicator lights will switch on for a few
seconds, then they will switch off and the START/PAUSE indicator light will pulse.
2. Load the laundry and close the door.
3. Set the WASH CYCLE knob to the desired programme.
4. Set the washing temperature (see Personalisation).
5. Set the spin speed (see Personalisation).
6. Measure out the detergent and washing additives (see Detergents and laundry).
7. Select the desired functions.
8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit
in a fixed manner, in green.
To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.
9. At the end of the wash cycle the
indicator light will switch on. The DOOR LOCKED indicator light will switch
off, indicating that the door may be opened. Take out your laundry and leave the appliance door ajar to make
sure the drum dries completely. Switch the washing machine off by pressing the ON/OFF button.
Wash
Rinse
Spin
Drain no spin
End of wash cycle
6
GB
Special wash cycles
Sanitizing cycle (wash cycle 6). A high-temperature hygienic wash cycle (over 60°C) which requires the use of bleach.
Pour the bleach, the detergent and the additives into the relevant compartments (see paragraph entitled
Detergent dispenser drawer).
Goodnight cycle (wash cycle 7). This is a silent cycle which can be run at night, when the electricity prices are lower.
The wash cycle is designed for cottons and synthetics. At the end of the cycle the machine stops while there is still water
in the drum; to spin and drain the laundry press the START/PAUSE button; alternatively the machine will perform the spin
cycle and drain the water automatically after 8 hours.
Baby cycle (wash cycle 8). This wash cycle can be used to remove the soiling typically caused by babies, while ensuring
that all detergent is removed from nappies in order to prevent the delicate skin of babies from suffering allergies. The
cycle has been designed to reduce the amount of bacteria by using a greater quantity of water and optimising the effect
of special disinfecting additives added to the detergent.
At the end of the wash cycle, the machine will slowly rotate the drum to prevent the formation of creases; to end the cycle
press the START/PAUSE button.
Mix 30 (wash cycle 4) this wash cycle was designed to wash lightly soiled garments quickly: it lasts just 30 minutes and
therefore saves both energy and time. By selecting this wash cycle (4 at 30°C), it is possible to wash different fabrics
together (except for wool and silk items), with a maximum load of 3 kg.
Mix 15 (wash cycle 5) this wash cycle was designed to wash lightly soiled garments quickly: it lasts just 15 minutes and
therefore saves both energy and time. By selecting this wash cycle (5 at 30°C), it is possible to wash different fabrics
together (except for wool and silk items), with a maximum load of 1.5 kg.
Wash cycles
The information contained in the table is intended as a guide only.
For all Test Institutes:
1) Test wash cycle in compliance with regulation EN 60456: set wash cycle 6 with a temperature of 60°C.
2) Long wash cycle for cottons: set wash cycle 1 with a temperature of 40°C.
3) Short wash cycle for cottons: set wash cycle 2 with a temperature of 40°C.
Wash cycles
Table of wash cycles
Description of the wash cycle
Max
.
temp.
(°C)
Max.
speed
(rpm)
Detergents
Max.
load
(kg)
Cycle
duration
Bleach Wash
Fabric
softener
Special cycles
6
Sanitizing cycle:
Extremely soiled whites.
90° 800
ll l
5
6
Sanitizing cycle (1):
Heavily soiled whites and resistant colours.
60° 800 -
ll
5
7
Goodnigt cycle:
Lightly soiled delicate colours.
40° 800 -
ll
3
8
Baby cycle:
Heavily soiled delicate colours.
40° 800 -
ll
2
9
Shirts
40° 600 -
ll
2
10
Silk/Curtains:
For garments in silk and viscose, lingerie.
30° 0 -
ll
1
11
Wool:
For wool, cashmere, etc.
40° 600 -
ll
1
Everyday wash cycles (Daily)
1
Cotton:
Heavily soiled whites and resistant colours.
60° 800
ll l
5
1
Cotton (2):
Heavily soiled whites and delicate colours.
40° 800
ll l
5
2
Coloured Cottons (3):
Lightly soiled whites and delicate colours.
40° 800
ll l
5
3
Synthetics resistents:
Heavily soiled resistant colours.
60° 800 -
ll
2,5
3
Synthetics delicates:
Lightly soiled resistant colours.
40° 800 -
ll
2,5
4
Mix 30':
To refresh lightly soiled garments quickly (not suitable for wool,
silk and clothes which require washing by hand).
30° 800 -
ll
3
5
Mix 15':
To refresh lightly soiled garments quickly (not suitable for wool,
silk and clothes which require washing by hand).
30° 800 -
ll
1,5
Partials wash cycles
A
Rinse - 800 - -
l
5
B
Light Rinse - 800 - -
l
2,5
C
Spin - 800 - - - 5
D
Light spin - 800 - - - 2,5
E
Drain no spin - 0 - - - 5
The duration of the wash cycles can be checked on the display.
GB
7
Setting the temperature
By pressing the TEMPERATURE button to set the wash temperature (see Table of wash cycles).
The temperature may be lowered, or even set to a cold wash (
).
The washing machine will automatically prevent you from selecting a temperature which is higher than the
maximum value set for each wash cycle.
Setting the spin speed
By pressing the SPIN SPEED button to set the spin speed for the selected wash cycle.
The maximum spin speeds available for each wash cycle are as follows:
Wash cycles Maximum spin speed
Cottons 800 rpm
Synthetics 800 rpm
Wool 600 rpm
Silk drain only
The spin speed may be lowered, or the spin cycle can be excluded altogether by selecting the symbol
.
The washing machine will automatically prevent you from selecting a spin speed which is higher than the
maximum speed set for each wash cycle.
Functions
The various wash functions available with this washing machine will help to achieve the desired results, every time.
To activate the functions:
1. Press the button corresponding to the desired function;
2. the function is enabled when the corresponding indicator light is illuminated.
Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in
conjunction with the selected wash cycle.
Delay timer
To set a delayed start for the selected wash cycle, press the button repeatedly until the desired delay time is
displayed (this may be between 1 hour and 24 hours).
To disable the function press the button until the text
is displayed.
N.B. Once you have pressed the START/PAUSE button, the delay time may only be decreased if you wish to modify it.
This option is enabled with all programmes.
Super Wash
Because a greater quantity of water is used in the initial phase of the cycle, and because of the increased cycle
duration, this function offers a high-performance wash.
This function may not be used in conjunction with wash cycles 4, 5, 6, 10, 11, A, B, C, D, E.
Extra rinse
By selecting this function, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is
particularly useful for sensitive skin.
This function may not be used in conjunction with wash cycles 4, 5, C, D, E.
Easy iron
By selecting this function, the wash and spin cycles will be modified in order to reduce the formation of creases. At
the end of the cycle the washing machine will perform slow rotations of the drum; the EASY IRON and START/
PAUSE indicator lights will flash (orange) and the
phase will remain lit in a fixed manner. To end the cycle, press
the START/PAUSE button or the EASY IRON button.
For the Silk wash cycle, the machine will end the cycle while the laundry is soaking, the EASY IRON and START/
PAUSE indicator lights will flash (orange) and the RINSE phase will remain lit in a fixed manner. To drain the water
so that the laundry may be removed, press the START/PAUSE button or the EASY IRON button.
This function may not be used in conjunction with wash cycles 4, 5, 6, 7, 8, 11, C, D, E.
Personalisation
8
GB
Detergents and laundry
Detergent dispenser drawer
Good washing results also depend on the correct
dose of detergent: adding too much detergent will not
necessarily result in a more efficient wash, and may in
fact cause build up on the inside of your appliance
and contribute to environmental pollution.
Do not use hand washing detergents because these
create too much foam.
Open the detergent
dispenser drawer and
pour in the detergent or
washing additive, as
follows.
compartment 1: Pre-wash detergent (powder)
Before pouring in the detergent, make sure that extra
compartment 4 has been removed.
compartment 2: Detergent for the wash cycle
(powder or liquid)
Liquid detergent should only be poured in immediately
prior to the start of the wash cycle.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
extra compartment 4: Bleach
Bleach cycle
Bleaching may only be performed in conjunction with
wash cycles 1, 2, 6.
Pour the bleach into extra compartment 4; pour the
detergent and softener into the corresponding
compartments, then select one of the
abovementioned wash cycles.
This option is recommended only for very soiled
cotton garments.
Preparing the laundry
Divide the laundry according to:
- the type of fabric/the symbol on the label.
- the colours: separate coloured garments from
whites
Empty all garment pockets and check the buttons.
Do not exceed the listed values, which refer to the
weight of the laundry when dry:
Durable fabrics: max. 5 kg
Synthetic fabrics: max. 2.5 kg
Delicate fabrics: max. 2 kg
Wool: max. 1 kg
MAX
1
2
4
3
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g
Garments requiring special care
Shirts: use special wash cycle 9 to wash shirts in
various fabrics and colours.
It guarantees maximum care is taken of the garments
and minimises the formation of creases.
Silk: use special wash cycle 10 to wash all silk
garments. We recommend the use of special
detergent which has been designed to wash delicate
clothes.
Curtains: fold curtains and place them in a pillow
case or mesh bag. Use wash cycle 10.
Wool: Hotpoint/Ariston is the only washing machine
manufacturer to have been awarded the prestigious
Woolmark Platinum Care endorsement (M.0508) by
the Woolmark Company, which means that all
woollen garments may be washed in the washing
machine, even those which state hand wash only
on the label. Wash cycle 11 therefore offers
complete peace of mind when washing woollen
garments in the washing machine (max. load 1 kg)
and guarantees optimal performance.
Load balancing system
Before every spin cycle, to avoid excessive vibrations
and to distribute the load in a uniform manner, the
drum rotates continuously at a speed which is slightly
greater than the washing rotation speed. If, after
several attempts, the load is not balanced correctly,
the machine spins at a reduced spin speed. If the
load is excessively unbalanced, the washing machine
performs the distribution process instead of spinning.
To encourage improved load distribution and balance,
we recommend small and large garments are mixed
in the load.
GB
9
Precautions and tips
This washing machine was designed and
constructed in accordance with international safety
regulations. The following information is provided for
safety reasons and must therefore be read carefully.
General safety
This appliance was designed for domestic use only.
The washing machine must only be used by adults, in
accordance with the instructions provided in this manual.
Do not touch the machine when barefoot or with
wet or damp hands or feet.
Do not pull on the power supply cable when
unplugging the appliance from the electricity
socket. Hold the plug and pull.
Do not open the detergent dispenser drawer while
the machine is in operation.
Do not touch the drained water as it may reach
extremely high temperatures.
Never force the porthole door. This could damage
the safety lock mechanism designed to prevent
accidental opening.
If the appliance breaks down, do not under any
circumstances access the internal mechanisms in
an attempt to repair it yourself.
Always keep children well away from the appliance
while it is operating.
The door can become quite hot during the wash cycle.
If the appliance has to be moved, work in a group
of two or three people and handle it with the utmost
care. Never try to do this alone, because the
appliance is very heavy.
Before loading laundry into the washing machine,
make sure the drum is empty.
Disposal
Disposing of the packaging materials: observe local
regulations so that the packaging may be re-used.
The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment, requires that
old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected
separately in order to optimise the recovery and
recycling of the materials they contain and reduce
the impact on human health and the environment.
The crossed out "wheeled bin" symbol on the
product reminds you of your obligation, that when
you dispose of the appliance it must be separately
collected.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
Opening the porthole door manually
In the event that it is not possible to open the
porthole door due to a powercut, and if you wish to
remove the laundry, proceed as follows:
1. remove the plug from
the electrical socket.
2. make sure the water
level inside the machine is
lower than the door
opening; if it is not, remove
excess water using the
drain hose, collecting it in a
bucket as indicated in the
figure.
3. using a screwdriver,
remove the cover panel on
the lower front part of the
washing machine (see
figure).
4. pull outwards using the tab as indicated in the
figure, until the plastic tie-rod is freed from its stop
position; pull downwards and open the door at the
same time.
5. reposition the panel, making sure the hooks are
securely in place before you push it onto the
appliance.
20
10
GB
Care and maintenance
Cutting off the water and electricity
supplies
Turn off the water tap after every wash cycle. This
will limit wear on the hydraulic system inside the
washing machine and help to prevent leaks.
Unplug the washing machine when cleaning it and
during all maintenance work.
Cleaning the washing machine
The outer parts and rubber components of the
appliance can be cleaned using a soft cloth soaked
in lukewarm soapy water. Do not use solvents or
abrasives.
Cleaning the detergent dispenser
drawer
Remove the dispenser
by raising it and pulling it
out (see figure).
Wash it under running
water; this operation
should be repeated
frequently.
Caring for the door and drum of your
appliance
Always leave the porthole door ajar in order to
prevent unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-cleaning
pump which does not require any maintenance.
Sometimes, small items (such as coins or buttons)
may fall into the pre-chamber which protects the
pump, situated in its bottom part.
Make sure the wash cycle has finished and unplug
the appliance.
To access the pre-chamber:
1. using a screwdriver,
remove the cover panel
on the lower front part of
the washing machine
(see figure);
2. unscrew the lid by
rotating it anti-clockwise
(see figure): a little water
may trickle out. This is
perfectly normal;
3. clean the inside thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks are
securely in place before you push it onto the
appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If there are
any cracks, it should be replaced immediately: during
the wash cycles, water pressure is very strong and a
cracked hose could easily split open.
Never use second-hand hoses.
1
2
GB
11
Troubleshooting
Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see Assistance),
make sure that the problem cannot be not solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not
take in water (the indicator light
for the first wash cycle stage
flashes rapidly).
The washing machine
continuously takes in and drains
water.
The washing machine does not
drain or spin.
The washing machine vibrates a
lot during the spin cycle.
The washing machine leaks.
The START/PAUSE indicator light
(orange) and the function
indicator lights flash rapidly.
There is too much foam.
Possible causes / Solutions:
The appliance is not plugged into the socket fully, or is not making contact.
There is no power in the house.
The washing machine door is not closed properly.
The ON/OFF button has not been pressed.
The START/PAUSE button has not been pressed.
The water tap has not been opened.
A delayed start has been set (using the Delay Timer, see Personalisation).
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap has not been opened.
There is no water supply in the house.
The pressure is too low.
The START/PAUSE button has not been pressed.
The drain hose is not fitted at a height between 65 and 100 cm from the
floor (see Installation).
The free end of the hose is under water (see Installation).
The wall drainage system is not fitted with a breather pipe.
If the problem persists even after these checks, turn off the water tap,
switch the appliance off and contact the Assistance Service. If the dwelling is
on one of the upper floors of a building, there may be problems relating to
water drainage, causing the washing machine to fill with water and drain
continuously. Special anti-draining valves are available in shops and help to
avoid this inconvenience.
The wash cycle does not include draining: some wash cycles require the
drain phase to be started manually.
The EASY IRON function has been activated: To complete the wash cycle,
press the START/PAUSE button (Personalisation).
The drain hose is bent (see Installation).
The drainage duct is clogged.
The drum was not unlocked correctly during installation (see Installation).
The washing machine is not level (see Installation).
The washing machine is trapped between cabinets and walls (see Installation).
The water inlet hose is not screwed on properly (see Installation).
The detergent dispenser drawer is blocked (for cleaning instructions, see Care
and maintenance).
The drain hose is not fixed properly (see Installation).
Switch off the machine and unplug it, wait for approximately 1 minute and
then switch it back on again.
If the problem persists, contact the Technical Assistance Service.
The detergent is not suitable for machine washing (it should display the text
for washing machines or hand and machine wash, or the like).
Too much detergent was used.
12
GB
Service
Before calling for Assistance:
Check whether you can solve the problem alone (see Troubleshooting);
Restart the programme to check whether the problem has been solved;
If this is not the case, contact an authorised Technical Assistance Centre using the telephone number
provided on the guarantee certificate.
Always request the assistance of authorised technicians.
Have the following information to hand:
the type of problem;
the appliance model (Mod.);
the serial number (S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also
be found on the front of the appliance by opening the door.
!
PL
Polski
Spis treci
Instalacja, 14-15
Rozpakowanie i wypoziomowanie
Pod³¹czenia hydrauliczne i elektryczne
Pierwszy cykl prania
Dane techniczne
Opis pralki i uruchamianie programu, 16-17
Panel sterowania
Kontrolki
Uruchamianie programu
Programy, 18
Tabela programów
Personalizacja, 19
Ustawianie temperatury
Ustawianie wirowania
Funkcje
rodki pior¹ce i bielizna, 20
Szufladka na rodki pior¹ce
Cykl wybielania
Przygotowanie bielizny
Tkaniny wymagaj¹ce szczególnego traktowania
System równowa¿enia ³adunku
Zalecenia i rodki ostro¿noci, 21
Ogólne zasady bezpieczeñstwa
Utylizacja
Rêczne otwieranie okr¹g³ych drzwiczek
Utrzymanie i konserwacja, 22
Od³¹czenie wody i pr¹du elektrycznego
Czyszczenie pralki
Czyszczenie szufladki na rodki pior¹ce
Konserwacja okr¹g³ych drzwiczek i bêbna
Czyszczenie pompy
Kontrola przewodu doprowadzaj¹cego wodê
Nieprawid³owoci w dzia³aniu i sposoby
ich usuwania, 23
Serwis Techniczny, 24
PL
ARSF 85
Instrukcja obs³ugi
PRALKA
"
PL
A
Instalacja
Nale¿y zachowaæ niniejsz¹ ksi¹¿eczkê, aby móc z
niej skorzystaæ w ka¿dej chwili. W przypadku
sprzeda¿y, odst¹pienia lub przeniesienia pralki w inne
miejsce nale¿y zadbaæ o przekazanie instrukcji wraz z
maszyn¹, aby nowy w³aciciel móg³ zapoznaæ siê z
dzia³aniem urz¹dzenia i z dotycz¹cymi go
ostrze¿eniami.
Nale¿y uwa¿nie przeczytaæ instrukcjê obs³ugi:
zawiera ona wa¿ne informacje dotycz¹ce instalacji oraz
w³aciwego i bezpiecznego u¿ytkowania pralki.
Rozpakowanie i wypoziomowanie
Rozpakowanie
1. Rozpakowaæ pralkê.
2. Sprawdziæ, czy nie dozna³a ona uszkodzeñ w czasie
transportu. W przypadku stwierdzenia uszkodzeñ nie
pod³¹czaæ jej i skontaktowaæ siê ze sprzedawc¹.
3. Odkrêciæ " ruby
zabezpieczaj¹ce
maszynê na czas
transportu oraz zdj¹æ
gumowy element z
podk³adk¹, znajduj¹cy siê
w tylnej czêci pralki
(patrz rysunek).
4. Zatkaæ otwory przy pomocy plastikowych zalepek,
znajduj¹cych siê w wyposa¿eniu maszyny.
5. Zachowaæ wszystkie czêci: w razie koniecznoci
przewiezienia pralki w inne miejsce, powinny one
zostaæ ponownie zamontowane.
Czêci opakowania nie zabawkami dla dzieci.
Poziomowanie
1. Ustawiæ pralkê na p³askiej i twardej pod³odze, nie
opieraj¹c jej o ciany, meble itp.
2. Jeli pod³oga nie jest
idealnie pozioma, nale¿y
skompensowaæ
nierównoci, odkrêcaj¹c
lub dokrêcaj¹c przednie
nó¿ki (patrz rysunek); k¹t
nachylenia, zmierzony na
górnym blacie pralki nie
powinien przekraczaæ 2°.
Staranne wypoziomowanie pralki zapewnia jej
stabilnoæ i zapobiega wibracjom, ha³asowi oraz
przesuwaniu siê maszyny w czasie pracy. W razie
ustawienia na dywanie lub wyk³adzinie dywanowej
nale¿y tak wyregulowaæ nó¿ki, aby pod pralk¹
pozostawa³a wolna przestrzeñ niezbêdna dla
wentylacji.
Pod³¹czenia hydrauliczne i elektryczne
Pod³¹czenie przewodu doprowadzaj¹cego wodê
1. Wsun¹æ uszczelkê A
do koñcówki przewodu
doprowadzaj¹cego wodê i
przykrêciæ go do kurka
zimnej wody z
gwintowanym przy³¹czem
3/4 GAS (patrz rysunek).
Przed pod³¹czeniem
spuszczaæ wodê do
momentu, a¿ stanie siê
ona ca³kowicie przezroczysta.
2. Pod³¹czyæ do maszyny
przewód doprowadzaj¹cy
wodê, przykrêcaj¹c go do
odpowiedniego otworu
dop³ywowego,
znajduj¹cego siê w tylnej
czêci pralki, z prawej
strony u góry
(patrz rysunek).
3. Zwróciæ uwagê, aby na przewodzie nie by³o zagiêæ
ani zwê¿eñ.
Cinienie wody w kurku powinno mieciæ siê w
przedziale podanym w tabeli Danych technicznych
(patrz strona obok).
Jeli d³ugoæ przewodu doprowadzaj¹cego wodê jest
niewystarczaj¹ca, nale¿y zwróciæ siê do
specjalistycznego sklepu lub do autoryzowanego
technika.
Nigdy nie instalowaæ ju¿ u¿ywanych przewodów.
Stosowaæ przewody znajduj¹ce siê w wyposa¿eniu
maszyny.
#
PL
65 - 100 cm
Pod³¹czenie przewodu odp³ywowego
Pod³¹czyæ przewód
odp³ywowy, nie zginaj¹c
go, do rury ciekowej lub
do otworu odp³ywowego w
cianie, które powinny
znajdowaæ siê na
wysokoci od 65 do 100
cm od pod³ogi;
ewentualnie oprzeæ go na
brzegu zlewu lub wanny,
przymocowuj¹c do kranu
prowadnik, znajduj¹cy siê
w wyposa¿eniu (patrz
rysunek). Wolny koniec
przewodu odp³ywowego
nie powinien byæ
zanurzony w wodzie.
Odradza siê stosowanie przewodów przed³u¿aj¹cych;
jeli to konieczne, przewód przed³u¿aj¹cy powinien
mieæ tak¹ sam¹ rednicê jak oryginalny, a jego d³ugoæ
nie mo¿e przekraczaæ 150 cm.
Pod³¹czenie elektryczne
Przed w³o¿eniem wtyczki do gniazdka elektrycznego
nale¿y siê upewniæ, czy:
gniazdko posiada uziemienie i jest zgodne z
obowi¹zuj¹cymi przepisami;
gniazdko jest w stanie wytrzymaæ maksymalne
obci¹¿enie mocy maszyny, wskazane w tabeli
Danych technicznych (patrz obok);
napiêcie zasilania mieci siê w wartociach
wskazanych w tabeli Danych technicznych
(patrz obok);
gniazdko pasuje do wtyczki pralki. W przeciwnym
razie nale¿y wymieniæ gniazdko lub wtyczkê.
Nie nale¿y instalowaæ pralki na otwartym powietrzu,
nawet w os³oniêtym miejscu, gdy¿ wystawienie
urz¹dzenia na dzia³anie deszczu i burz jest bardzo
niebezpieczne.
Po zainstalowaniu pralki gniazdko elektryczne
powinno byæ ³atwo dostêpne.
Nie u¿ywaæ przed³u¿aczy ani rozga³êników.
Przewód nie powinien byæ pozginany ani
przygnieciony.
Przewód zasilania elektrycznego mo¿e byæ
wymieniany wy³¹cznie przez autoryzowanych
techników.
Uwaga! Producent nie ponosi ¿adnej odpowiedzialnoci
w przypadku nieprzestrzegania powy¿szych zasad.
Pierwszy cykl prania
Po zainstalowaniu pralki, przed przyst¹pieniem do jej
u¿ytkowania, nale¿y wykonaæ jeden cykl prania ze
rodkiem pior¹cym, ale bez wsadu, nastawiaj¹c
program 1.
Dane techniczne
Model
ARSF 85
Wymiary
szerokoæ cm 59,5
wysokoæ cm 85
g³êbokoæ cm 40
Pojemnoæ
od 1 do 5 kg
Dane pr¹du
elektrycznego
dane techniczne umieszczone na
tabliczce na maszynie
Dane sieci
wodocgowej
Maksymalne cinienie 1 MPa (10 barów)
cinienie minimalne 0,05 MPa (0,5 barów)
pojemnoæ bêbna 40 litrów
Szybkoæ wirowania
do 800 obrotów na minutê
Programy kontrolne
zgodnie z przepisami
EN 60456
program 6; temperatura 60°C;
wykonane przy 5 kg za³adowanej
bielizny.
Urz¹dzenie to zosto wyprodukowane
zgodnie z nastêpuj¹cymi przepisami EWG:
- 73/23/CEE z dn. 19/02/73 (o Niskim
Napiêciu) wraz z kolejnymi zmianami
- 89/336/CEE z dn. 03/05/89
(o Kompatybilnoci Elektromagnetycznej)
wraz z kolejnymi zmianami
- 2002/96/CE
$
PL
Szufladka na rodki pior¹ce: do dozowania
rodków pior¹cych i dodatków (patrz rodki pior¹ce
i bielizna).
Wewn¹trz szufladki na rodki pior¹ce znajduje siê
pulpit, na którym w ka¿dej chwili mo¿na odczytaæ
skrótowy schemat programów.
Przycisk z kontrolk¹ W£¥CZANIA/WY£¥CZANIA:
aby w³¹czyæ lub wy³¹czyæ urz¹dzenie.
Zapalona kontrolka wskazuje, ¿e urz¹dzenie jest
w³¹czone.
Pokrêt³o PROGRAMÓW: do ustawiania programów.
W czasie trwania programu pokrêt³o pozostaje
nieruchome.
Przycisk WIROWANIA: do nastawienia lub
wy³¹czenia wirowania (patrz Personalizacja).
Przycisk TEMPERATURY: do regulacji temperatury
prania lub do nastawienia prania w zimnej wodzie
(patrz Personalizacja).
WYWIETLACZ: aby wywietliæ czas pozostaj¹cy
do zakoñczenia wybranego cyklu prania oraz, jeli
zosta³o ustawione opónienie startu, czas
pozostaj¹cy do rozpoczêcia prania.
Przycisk z kontrolk¹ BLOKADY PRZYCISKÓW: aby
w³¹czyæ lub wy³¹czyæ blokadê panelu sterowania.
Przyciski z kontrolkami FUNKCJI: do wyboru
dostêpnych funkcji. Kontrolka wybranej funkcji
pozostaje zawiecona.
Kontrolki STANU ZAAWANSOWANIA CYKLU:
umo¿liwiaj¹ kontrolê stanu zaawansowania
programu prania.
Kontrolka BLOKADY OKR¥G£YCH DRZWICZEK:
pozwala sprawdziæ czy mo¿liwe jest otwarcie
okr¹g³ych drzwiczek (patrz strona obok).
Przycisk z kontrolk¹ START/PAUZA: do
uruchamiania programów lub ich chwilowego
przerywania.
N.B.: aby przerwaæ wykonywane pranie, nale¿y
nacisn¹æ ten przycisk, jego kontrolka zacznie
pulsowaæ na pomarañczowo, natomiast kontrolka
bie¿¹cej fazy bêdzie wieciæ ci¹g³ym wiat³em.
Jeli kontrolka BLOKADY OKR¥G£YCH
DRZWICZEK
jest wy³¹czona, mo¿na otworzyæ
drzwiczki pralki.
W celu ponownego uruchomienia prania od
momentu, w którym zosta³o ono przerwane, nale¿y
ponownie nacisn¹æ ten przycisk.
Opis pralki i
uruchamianie programu
Kontrolka
BLOKADY
OKR¥G£YCH
DRZWICZEK
Panel sterowania
Przyciski z
kontrolkami
FUNKCJI
Przycisk z
kontrolk¹
START/PAUZA
Kontrolki
STANU
ZAAWANSOWANIA CYKLU
Szufladka na rodki pior¹ce
Pokrêt³o
PROGRAMÓW
WYWIETLACZ
Przycisk z kontrolk¹
W£¥CZANIA/
WY£¥CZANIA
Przycisk
TEMPERATURY
Przycisk
WIROWANIA
Przycisk z
kontrolk¹
BLOKADY
PRZYCISKÓW
%
PL
Kontrolki
Kontrolki dostarczaj¹ wa¿nych informacji.
Oto co sygnalizuj¹:
Kontrolki bie¿¹cej fazy prania
Przy obracaniu pokrêt³em PROGRAMÓW kontrolki
bêd¹ siê zapalaæ, wskazuj¹c kolejne fazy pracy,
które wykona urz¹dzenie na podstawie ustawionego
programu.
Po wybraniu i uruchomieniu ¿¹danego cyklu prania
kontrolki bêd¹ siê kolejno zapalaæ, wskazuj¹c stan
zaawansowania programu:
Przyciski funkcyjne i ich kontrolki
Po dokonaniu wyboru funkcji jej kontrolka zawieci siê.
W przypadku wyboru funkcji niezgodnej z
ustawionym programem jej kontrolka zacznie
pulsowaæ, zostanie wyemitowany sygna³ dwiêkowy,
a funkcja nie w³¹czy siê.
Jeli ustawiona funkcja bêdzie sprzeczna z inn¹,
wybran¹ wczeniej, uwzglêdniony zostanie tylko
ostatni dokonany wybór.
Kontrolka temperatury
Przy wyborze wartoci temperatury zawieci siê
w³aciwa kontrolka.
Kontrolka wirowania
Przy wyborze prêdkoci wirowania zawieci siê
w³aciwa kontrolka.
Kontrolka blokady przycisków
Aby w³¹czyæ blokadê panelu sterowania, nale¿y
przytrzymaæ przycisk wciniêty przez oko³o 2
sekundy. Zapalona kontrolka wskazuje, ¿e panel
sterowania jest zablokowany. W ten sposób
uniemo¿liwia siê dokonywanie przypadkowych
zmian w programach, zw³aszcza jeli w domu
dzieci.
Aby wy³¹czyæ blokadê panelu sterowania, nale¿y
przytrzymaæ przycisk wciniêty przez oko³o 2
sekundy.
Kontrolka blokady okr¹g³ych drzwiczek
Zapalona kontrolka wskazuje, ¿e okr¹g³e drzwiczki
pralki zablokowane, aby zapobiec ich
przypadkowemu otwarciu. Przed przyst¹pieniem do
otwierania drzwiczek nale¿y poczekaæ, a¿ kontrolka
zganie, w przeciwnym razie mo¿na spowodowaæ
ich uszkodzenie.
N.B.: jeli funkcja Opónienie startu jest
w³¹czona, nie mo¿na otworzyæ okr¹g³ych drzwiczek,
w celu ich otwarcia konieczne jest chwilowe
zatrzymanie urz¹dzenia poprzez naciniêcie
przycisku START/PAUZA.
Szybkie pulsowanie (pomarañczowej) kontrolki
START/PAUZA równoczenie z kontrolk¹ funkcji
sygnalizuje wyst¹pienie nieprawid³owoci w
dzia³aniu pralki (patrz Nieprawid³owoci w dzia³aniu i
sposoby ich usuwania).
Uruchamianie programu
1. W³¹czyæ pralkê, naciskaj¹c przycisk W£¥CZANIE / WY£¥CZANIE . Wszystkie kontrolki zapal¹ siê na kilka
sekund, nastêpnie wy³¹cz¹ siê i zacznie pulsowaæ kontrolka START/PAUZA.
2. Za³adowaæ bieliznê i zamkn¹æ drzwiczki pralki.
3. Ustawiæ ¿¹dany program przy pomocy pokrêt³a PROGRAMÓW.
4. Ustawiæ temperaturê prania (patrz Personalizacja).
5. Ustawiæ szybkoæ wirowania (patrz Personalizacja).
6. Wsypaæ rodek pior¹cy i dodatki (patrz rodki pior¹ce i bielizna).
7. Wybraæ ¿¹dane funkcje.
8. Uruchomiæ program naciskaj¹c przycisk START/PAUZA, kontrolka programu bêdzie wieciæ ci¹g³ym wiat³em w
kolorze zielonym. Aby anulowaæ ustawiony cykl, nale¿y chwilowo zatrzymaæ urz¹dzenie, naciskaj¹c przycisk
START/PAUZA, i wybraæ nowy cykl.
9. Po zakoñczeniu programu zapali siê kontrolka
. Kontrolka BLOKADY DRZWICZEK zganie, wskazuj¹c, ¿e
otwarcie drzwiczek jest mo¿liwe. Wyj¹æ bieliznê i pozostawiæ drzwiczki pralki uchylone, aby bêben móg³ wyschn¹æ.
Wy³¹czyæ pralkê, naciskaj¹c przycisk W£¥CZANIE/WY£¥CZANIE.
Pranie zasadnicze
P³ukanie
Wirowanie
Wydalanie wody
Koniec cyklu
&
PL
rodki pior¹ce
Opis programu
Temp.
max
(°C)
Prêdkoæ
max
(obrotów
na minutê)
Wybielacz Pranie
rodek
zmiêkczaj¹cy
£adunek max (kg) Czas trwania cyklu
Programy specjalne
6
CYKL HIGIENICZNY:
Tkaniny bia³e bardzo mocno
zabrudzone.
90° 800
5
6
CYKL HIGIENICZNY (1):
Tkaniny bia³e i
kolorowe, wytrzyma³e, mocno zabrudzone.
60° 800 -
5
7
PROGRAM SPOKOJNY SEN:
Tkaniny
kolorowe, delikatne, lekko zabrudzone.
40° 800 -
3
8 BABY:
Tkaniny kolorowe, delikatne, mocno zabrudzone.
40° 800 -
2
9 KOSZULE
40° 600 -
2
10 JEDWAB/FIRANY:
Do jedwabiu, wiskozy, bielizny.
30° 0 -
1
11 WE£NA:
Do we³ny, kaszmiru, itp.
40° 600 -
1
Programy codzienne
1
BAWE£NA:
Tkaniny bia³e i kolorowe,
wytrzyma³e, mocno zabrudzone.
60° 800
5
1
BAWE£NA (2):
Tkaniny bia³e i kolorowe,
delikatne, mocno zabrudzone.
40° 800
5
2
BAWE£NA KOLOROWE (3):
Tkaniny bia³e lekko
zabrudzone i delikatne kolorowe.
40° 800
5
3
SYNTETYCZNE:
Tkaniny kolorowe, wytrzyma³e,
mocno zabrudzone.
60° 800 -
2,5
3
SYNTETYCZNE:
Tkaniny kolorowe, wytrzyma³e,
lekko zabrudzone.
40° 800 -
2,5
4
MIX 30':
W celu szybkiego odwie¿enia lekko
zabrudzonych tkanin (niewskazany dla we³ny, jedwabiu
i tkanin przeznaczonych do prania rêcznego).
30° 800 -
3
5
MIX 15’:
W celu szybkiego odwie¿enia lekko
zabrudzonych tkanin (niewskazany dla we³ny, jedwabiu
i tkanin przeznaczonych do prania rêcznego).
30° 800 -
1,5
Programy czêciowe
A
P³ukanie
- 800 - -
5
B
P³ukanie delikatne
- 800 - -
2,5
C
Wirowanie
- 800 - - - 5
D
Wirowanie delikatne
- 800 - - - 2,5
E
Wydalanie
wody
- 0 - - - 5
Programy specjalne
CYKL HIGIENICZNY (program 6). Wysokotemperaturowy program higienizuj¹cy, który przewiduje u¿ycie
wybielacza w temperaturze powy¿ej 60°C. Aby wybieliæ pranie, nale¿y umieciæ w odpowiednich przegródkach
wybielacz, rodek pior¹cy i dodatki (patrz paragraf Szufladka na rodki pior¹ce).
PROGRAM SPOKOJNY SEN (program 7). Jest to cichy cykl, który mo¿e byæ uruchamiany w nocy, w godzinach
ni¿szej taryfy energetycznej. Program ten zosta³ opracowany dla tkanin syntetycznych i bawe³nianych. Po
zakoñczeniu cyklu pralka zatrzymuje siê z wod¹ w bêbnie; aby wykonaæ wirowanie i odprowadzenie wody, nale¿y
nacisn¹æ przycisk START/PAUZA, w przeciwnym razie po 8 godzinach urz¹dzenie automatycznie odwiruje pranie i
odprowadzi wodê.
BABY (program 8). Program ten umo¿liwia usuniêcie z odzie¿y zabrudzeñ typowych dla dzieci, zapewniaj¹c przy
tym ca³kowite wyp³ukanie rodka pior¹cego z tkanin, aby unikn¹æ reakcji alergicznych, jakie móg³by on wywo³aæ na
delikatnej skórze dziecka. Cykl ten zosta³ opracowany w celu ograniczenia liczby bakterii poprzez wykorzystanie
wiêkszej iloci wody i optymalizacjê dzia³ania specjalnych dodatków higienizuj¹cych, którymi uzupe³niany jest
rodek pior¹cy.
Po zakoñczeniu prania urz¹dzenie wykona seriê wolnych obrotów bêbna, aby zapobiec powstaniu
zagnieceñ; w celu zakoñczenia cyklu nale¿y nacisn¹æ przycisk START/PAUZA.
MIX 30' (program 4) to program przeznaczony do prania lekko zabrudzonej bielizny w krótkim czasie: trwa on tylko 30
minut i pozwala dziêki temu na zaoszczêdzenie energii i czasu. Ustawiaj¹c program (4 w temperaturze 30°C) mo¿na
razem wypraæ ró¿nego rodzaju tkaniny (z wyj¹tkiem we³ny i jedwabiu), przy maksymalnym ³adunku 3 kg.
MIX 15' (program 5) to program przeznaczony do prania lekko zabrudzonej bielizny w krótkim czasie: trwa on tylko
15 minut i pozwala dziêki temu na zaoszczêdzenie energii i czasu. Ustawiaj¹c program (5 w temperaturze 30°C)
mo¿na razem wypraæ ró¿nego rodzaju tkaniny (z wyj¹tkiem we³ny i jedwabiu), przy maksymalnym ³adunku 1,5 kg.
Programy
Podane w tabeli dane maj¹ charakter orientacyjny.
Dla wszystkich Instytucji homologacyjnych:
1) Program kontrolny zgodny z norm¹ EN 60456: ustawiæ program 6, wybieraj¹c temperaturê 60°C.
2) Program bawe³na, d³ugi: ustawiæ program 1, wybieraj¹c temperaturê 40°C.
3) Program bawe³na, krótki: ustawiæ program 2, wybieraj¹c temperaturê 40°C.
Tabela programów
Programy
Mo¿liwa jest kontrola czasu trwania programów na wywietlaczu.
'
PL
Ustawianie temperatury
Naciskaj¹c przycisk TEMPERATURA ustawia siê temperaturê prania (patrz Tabela programów).
Temperaturê mo¿na zmniejszaæ, a¿ do prania w zimnej wodzie (
).
Pralka automatycznie uniemo¿liwi ustawienie temperatury wy¿szej od maksymalnej temperatury
przewidzianej dla danego programu.
Ustawianie wirowania
Naciskaj¹c przycisk WIROWANIE ustawia siê prêdkoæ wirowania dla wybranego programu.
Maksymalne prêdkoci przewidziane dla poszczególnych programów nastêpuj¹ce:
Programy Prêdkoæ maksymalna
Bawe³na 800 obrotów na minutê
Tkaniny syntetyczne 800 obrotów na minutê
We³na 600 obrotów na minutê
Jedwab tylko odprowadzenie wody
Prêdkoæ wirowania mo¿e zostaæ zmniejszona, mo¿na te¿ ca³kowicie wy³¹czyæ wirowanie, wybieraj¹c symbol
.
Pralka automatycznie uniemo¿liwi wykonanie wirowania z prêdkoci¹ wiêksz¹ ni¿ maksymalna prêdkoæ
wirowania przewidziana dla danego programu.
Funkcje
Ró¿ne funkcje, w jakie wyposa¿ona jest pralka, pozwalaj¹ na uzyskanie oczekiwanej czystoci i bieli prania.
Aby w³¹czyæ poszczególne funkcje, nale¿y:
1. nacisn¹æ przycisk odpowiadaj¹cy ¿¹danej funkcji;
2. zapalenie siê jego kontrolki sygnalizuje, ¿e funkcja jest w³¹czona.
Uwaga: Szybkie pulsowanie kontrolki wskazuje, ¿e danej funkcji nie mo¿na ustawiæ dla wybranego programu.
Start z opónieniem
Aby ustawiæ opónione uruchomienie wybranego programu, nale¿y naciskaæ przycisk a¿ do wywietlenia siê
¿¹danego opónienia (od 1 do 24 h).
W celu wy³¹czenia funkcji naciskaæ przycisk dopóki nie wywietli siê napis
.
N.B.: Po naciniêciu przycisku START/PAUZA wartoæ opónienia mo¿na zmieniæ tylko na mniejsz¹.
Jest aktywny ze wszystkimi programami.
Super Wash
Dzieki zastosowaniu wiekszej ilosci wody w poczatkowej fazie cyklu i wydluzeniu czasu trwania programu,
funkcja ta gwarantuje pranie o wysokiej skutecznosci.
Funkcji tej nie mo¿na w³¹czyæ w programach 4, 5, 6, 10, 11, A, B, C, D, E.
P³ukanie dodatkowe
Wybieraj¹c opcjê zwiêksza siê skutecznoæ p³ukania i zapewnia siê optymalne usuniêcie rodka
pior¹cego. Jest to przydatne w przypadku, gdy skóra jest szczególnie wra¿liwa na rodki pior¹ce.
Funkcji tej nie mo¿na w³¹czyæ w programach 4, 5, C, D, E.
£atwe prasowanie
Po wybraniu tej opcji pranie oraz wirowanie zostan¹ odpowiednio zmodyfikowane w celu ograniczenia
powstawania zagnieceñ. Po zakoñczeniu cyklu pralka wykona powolne obroty bêbna; kontrolka funkcji
£ATWE PRASOWANIE oraz kontrolka START/PAUZA bêd¹ pulsowaæ (pomarañczowym wiat³em),
natomiast kontrolka
bêdzie wieciæ wiat³em ci¹g³ym. W celu zakoñczenia cyklu nale¿y nacisn¹æ
przycisk START/PAUZA lub przycisk £ATWE PRASOWANIE.
W programie Jedwab po zakoñczeniu cyklu bielizna pozostanie namoczona, kontrolka funkcji £ATWE
PRASOWANIE oraz kontrolka START/PAUZA bêd¹ pulsowaæ (pomarañczowym wiat³em), natomiast
kontrolka P£UKANIA bêdzie wieciæ wiat³em ci¹g³ym. W celu odprowadzenia wody i umo¿liwienia wyjêcia
prania konieczne jest naciniêcie przycisku START/PAUZA lub przycisku £ATWE PRASOWANIE.
Funkcji tej nie mo¿na w³¹czyæ w programach 4, 5, 6, 7, 8, 11, C, D, E.
Personalizacja
PL
rodki pior¹ce i bielizna
Szufladka na rodki pior¹ce
Dobry rezultat prania zale¿y równie¿ od prawid³owego
dozowania rodka pior¹cego: u¿ycie jego nadmiernej
iloci nie poprawia skutecznoci prania, lecz
przyczynia siê do powstawania nalotów na
wewnêtrznych czêciach pralki i do zanieczyszczania
rodowiska.
Nie stosowaæ rodków do prania rêcznego, poniewa¿
tworz¹ one za du¿o piany.
Wysun¹æ szufladkê i
umieciæ w niej rodek
pior¹cy lub dodatkowy w
nastêpuj¹cy sposób.
przegródka 1: rodek pior¹cy do prania
wstêpnego (w proszku)
Przed wsypaniem rodka pior¹cego nale¿y sprawdziæ,
czy nie jest w³o¿ona dodatkowa przegródka 4.
przegródka 2: rodek pior¹cy do prania
w³aciwego (w proszku lub w p³ynie)
P³ynny rodek do prania nale¿y wlaæ dopiero przed
samym uruchomieniem programu.
przegródka 3: rodki dodatkowe
(zmiêkczaj¹ce, itp.)
rodek zmiêkczaj¹cy nie powinien wyp³ywaæ poza
kratkê.
dodatkowa przegródka 4: Wybielacz
Cykl wybielania
Wybielanie jest mo¿liwe tylko w programach , , $.
Wlaæ wybielacz do dodatkowej przegródki ", umieciæ
we w³aciwych przegródkach rodek pior¹cy i rodek
zmiêkczaj¹cy, po czym ustawiæ jeden z wy¿ej
wymienionych programów.
Zalecany tylko do prania bardzo zabrudzonej bielizny
bawe³nianej.
Przygotowanie bielizny
Podzieliæ bieliznê do prania wed³ug:
- rodzaju tkaniny / symbolu na etykietce.
- kolorów: oddzieliæ tkaniny kolorowe od bia³ych.
Opró¿niæ kieszenie i sprawdziæ guziki.
Nie przekraczaæ wskazanego ciê¿aru suchej
bielizny:
Tkaniny wytrzyma³e: max 5 kg
Tkaniny syntetyczne: max 2,5 kg
Tkaniny delikatne: max 2 kg
We³na: max 1 kg
MAX
1
2
4
3
Ile wa¿y bielizna?
1 przecierad³o 400-500 gr.
1 poszewka 150-200 gr.
1 obrus 400-500 gr.
1 szlafrok 900-1.200 gr.
1 rêcznik 150-250 gr.
Tkaniny wymagaj¹ce szczególnego
traktowania
Koszule: stosowaæ specjalny program 9
przeznaczony do prania koszul z ró¿nego rodzaju
tkanin i w ró¿nych kolorach.
Program ten pozwala zachowaæ je w doskona³ym
stanie, zmniejszaj¹c do minimum powstawanie
zagnieceñ.
Jedwab: stosowaæ odpowiedni program 10 do
prania wszelkiego rodzaju wyrobów z jedwabiu.
Zaleca siê stosowanie specjalnego rodka pior¹cego
do tkanin delikatnych.
Firany: w³o¿yæ je z³o¿one do poszewki lub do
siatkowatego worka. Stosowaæ program 10.
We³na: Hotpoint/Ariston to jedyna pralka, która
uzyska³a presti¿owe oznaczenie Woolmark
Platinum Care (M.0508) od The Woolmark Company,
które certyfikuje pranie w pralce wszystkich
wyrobów we³nianych, tak¿e tych z etykiet¹ tylko
pranie rêczne
. Korzystaj¹c z programu 11
mo¿na wiêc w pe³ni bezpiecznie praæ w pralce
wszystkie tkaniny we³niane (maks. 1 kg) z
gwarancj¹ uzyskania najlepszych rezultatów.
System równowa¿enia ³adunku
Przed ka¿dym wirowaniem, aby unikn¹æ
nadmiernych drgañ oraz jednorodnie roz³o¿yæ wsad,
bêben wykonuje obroty z prêdkoci¹ nieco wiêksz¹
ni¿ podczas prania. Jeli pomimo kolejnych prób
wsad nie zostanie równomiernie roz³o¿ony, maszyna
wykona wirowanie z prêdkoci¹ mniejsz¹ od
przewidzianej. W przypadku nadmiernego
niezrównowa¿enia pralka wykona roz³o¿enie wsadu
zamiast wirowania. Aby zapewniæ lepsze roz³o¿enie
wsadu oraz jego w³aciwe zrównowa¿enie, zaleca
siê wymieszanie du¿ych i ma³ych sztuk bielizny.
1 / 1

Hotpoint ARSF 85 (EU) Guida utente

Categoria
Lavatrici
Tipo
Guida utente