Electrolux TKGL5E101 Manuale utente

Marca: Electrolux

Modello: TKGL5E101

Categoria: Asciugatrici

Tipo: Manuale utente

user manual

istruzioni per l’uso

Condenser dryer

Asciugatrice

TK GL5 E

Electrolux. Thinking of you.

Share more of our thinking at www.electrolux.com

CONTENTS

Important safety information 2

Environment 4

Product description 5

Control panel 6

Before first use 7

Programme overview 7

Daily use 9

Care and cleaning 12

What to do if ... 15

Technical data 17

Machine settings 18

Hints for test institutes 18

Installation 19

Service 20

Subject to change without notice

IMPORTANT SAFETY INFORMATION

Important! In the interest of your safety

and to ensure the correct use, before

installing and first using the appliance,

read this user manual carefully,

including its hints and warnings. To

avoid unnecessary mistakes and

accidents, it is important to ensure that

all people using the appliance are

thoroughly familiar with its operation

and safety features. Save these

instructions and make sure that they

remain with the appliance if it is moved

or sold, so that everyone using it

through its life will be properly

informed on appliance use and safety.

- Please read the instruction book be-

fore using this appliance.

General safety

• It is dangerous to alter the specifications

or attempt to modify this product in any

way.

• This appliance is not intended for use by

persons (including children) with reduced

physical and sensory conditions or lack

of experience and knowledge, unless

they have been given supervision or in-

struction concerning use of the appliance

by a person responsible for their safety.

• Make sure that small children and pets

do not climb inside the drum. To avoid

this, please check into the drum before

using.

• Any objects such as coins, safety pins,

nails, screws, stones or any other hard,

sharp material can cause extensive dam-

age and must not be placed into the ma-

chine.

• In order to avoid danger of fires caused

by excessive drying, do not use appli-

ance to dry the following items: Cush-

ions, quilts etc. (these items accumulate

heat).

• Items such as foam rubber (latex foam),

shower caps, waterproof textiles, rubber

backed articles and clothes or pillows fit-

ted with foam rubber pads should not be

dried in the tumble dryer.

• Always unplug the appliance after use,

cleaning and maintenance.

• Under no circumstances should you at-

tempt to repair the machine yourself. Re-

pairs carried out by inexperienced per-

sons may cause injury or serious malfunc-

tioning. Contact your local Service Cen-

tre. Always insist on genuine spare parts.

• Items that have been soiled with substan-

ces such as cooking oil acetone, petrol,

kerosene, spot removers, turpentine, wax-

es and wax removers should be washed

in hot water with an extra amount of de-

tergent before being dried in the tumble

dryer.

• Danger of explosion: Never tumble dry

items that have been in contact with in-

flammable solvents (petrol, methylated

spirits, dry cleaning fluid and the like). As

these substances are volatile, they could

cause an explosion. Only tumble dry

items washed with water.

• Risk of fire: items that have been spot-

ted or soaked with vegetable or cooking

oil constitute a fire hazard and should not

be placed in the tumble dryer.

2 electrolux

• If you have washed your laundry with

stain remover you must execute an extra

rinse cycle before loading your tumble dry-

er.

• Please make sure that no gas lighters or

matches have accidentally been left in

pockets of garments incase they are loa-

ded into appliance

Warning!

• Risk of fire! Never stop a tumble

dry before the end of the drying

cycle unless all items are quickly

removed and spread out so that

the heat is dissipated.

•

Lint must not be allowed to accu-

mulate around the tumble dryer.

• Risk of electric shock! Do not spray

down the appliance with jets of water.

• The final part of a tumble dryer cycle oc-

curs without heat ( cool down cycle ) to

ensure that the items are left at a temper-

ature that ensures that items will not be

damaged.

• The tumble dryer is not to be used if in-

dustrial chemicals have been used for

cleaning.

• Ensure you have good ventilation in the in-

stallation room to avoid the back flow of

gases into the room from appliances burn-

ing other fuels, including open fires.

Installation

• This appliance is heavy. Care should be

taken when moving it.

• When unpacking the appliance, check

that it is not damaged. If in doubt, do not

use it and contact the Service Centre.

• All packaging must be removed before

use. Serious damage can occur to the

product and to property if this is not ad-

hered to. See relevant section in the user

manual.

• Any electrical work required to install this

appliance should be carried out by a quali-

fied electrician or competent person.

• If the machine is situated on a carpeted

floor, please adjust the feet in order to al-

low air to circulate freely under the appli-

ance.

• After having installed the appliance,

check that it is not pressing or standing

on its electrical supply cable.

• If the tumble dryer is placed on top of a

washing machine, it is compulsory to use

the stacking kit (optional accessory).

Use

• This appliance is designed for domestic

use. It must not be used for purposes oth-

er than those for which it was designed.

• Only wash fabrics which are designed to

be machine dried. Follow the instructions

on each garment label.

• Do not dry unwashed items in the tumble

dryer.

• Do not overload the appliance. See the

relevant section in the user manual.

• Clothes which are dripping wet should

not be placed in the dryer.

• Garments which have been in contact

with volatile petroleum products should

not be machine dried. If volatile cleaning

fluids are used, care should be taken to

ensure that the fluid is removed from the

garment before placing in the machine.

• Never pull the power supply cable to re-

move the plug from the socket; always

take hold of the plug itself.

• Never use the tumble dryer if the power

supply cable, the control panel, the work-

ing surface or the base are damaged so

that the inside of the tumble dryer is ac-

cessible.

• Fabric softeners, or similar products

should be used as specified by the fabric

softener instructions.

•

Caution - hot surface : Do not touch

the door light cover surface when the

light is switched on.

(Only dryers equipped with internal drum

light)

Child safety

• This machine is not intended for use by

young children or infirm persons without

supervision.

• Children often do not recognise the haz-

ards associated with electrical applian-

ces. Children should be supervised to en-

sure that they do not play with the appli-

ance.

electrolux 3

Warning!

• Danger of suffocation! The packag-

ing components (e.g. plastic film, pol-

ystyrene) can be dangerous to chil-

dren - Keep them out of children’s

reach.

• Keep all detergents in a safe place out of

children’s reach.

• Make sure that children or pets do not

climb inside the drum.

ENVIRONMENT

The symbol on the product or on its

packaging indicates that this product may

not be treated as household waste. Instead

it should be taken to the appropriate

collection point for the recycling of electrical

and electronic equipment. By ensuring this

product is disposed of correctly, you will

help prevent potential negative

consequences for the environment and

human health, which could otherwise be

caused by inappropriate waste handling of

this product. For more detailed information

about recycling of this product, please

contact your local council, your household

waste disposal service or the shop where

you purchased the product.

Environmental information

The packaging materials are environmental-

ly friendly and can be recycled. The plastic

components are identified by markings, e.g.

>PE<, >PS<, etc. Please dispose of the

packaging materials in the appropriate con-

tainer at the community waste disposal fa-

cilities.

Important! The heat pump of your tumble

dryer contains a closed refrigerant circuit

filled with a refrigerant which is free from

fluoro-chloro-hydrocarbons. The refrigerant

circuit in the heat pump must not be

damaged.

Warning! When a unit is no longer

being used:

• Pull the plug out of the socket.

• Cut off the cable and plug and dis-

pose of them.

• Dispose of the door catch. This pre-

vents children from trapping them-

selves inside and endangering their

lives.

4 electrolux

PRODUCT DESCRIPTION

1 Control panel

2 Water reservoir

3 Drum light

4 Fine fluff filters

5 Course fluff filters

6 Fluff filters

7 Rating plate

8 Loading door (reversible)

9 Heat exchanger door

10 Button for opening door in plinth

11 Ventilation grille

12 Adjustable feet

electrolux 5

CONTROL PANEL

Control panel

6 5 4

321

1 Programme selector and on/off switch

2 Function buttons

3 START PAUSE (Start / Pause) button

4 DELAY START (Zeitvorwahl) button

5 Display

6 Status LED

Display

1 time to end / error message

2 warnings

3 long anti-crease icon

4 cycle phase status

5 delay time option icon

6 child lock icon

Display description

drying (drying phase in-

dicator)

cooling (drying phase

indicator)

crease guard (drying

phase indicator)

long anti-crease

empty water reservoir

(warning)

clean filters (warning)

clean condenser (warn-

ing)

child lock

- -

6 electrolux

Display description

delay start cycle duration

time program scope

(10 min - 3h)

delay start scope

BEFORE FIRST USE

In order to remove any residues which may

have been produced during production,

wipe the dryer drum with a damp cloth or

carry out a brief drying cycle (ca. 30 min.)

with damp cloths in the machine.

PROGRAMME OVERVIEW

Programmes

max.

load

(weight

when

dry)

Application/properties Options

Care

mark

COTTONS (Baumwolle)

EXTRA DRY (Extra-

trocken)

8 kg

Thorough drying of thick or multi- lay-

ered fabrics, e.g. terry towelling

items, bathrobes.

all

except

TIME (Zeit-

wahl)

CUPBOARD DRY

(Schranktrocken)

8 kg

Thorough drying of fabrics of even

thicknesses, e.g. terry towelling

items, knitwear, towels.

all

except

TIME (Zeit-

wahl)

IRON DRY (Bügel-

trocken)

8 kg

For normal thickness cotton or linen

laundry, e.g. bedding, table linen.

all

except

TIME (Zeit-

wahl)

SYNTHETICS (Mischgewebe)

EXTRA DRY (Extra-

trocken)

3 kg

Thorough drying of thick or multi-lay-

ered fabrics, e.g. pullovers, bed-

ding, table linen.

all

except

TIME (Zeit-

wahl)

CUPBOARD DRY

(Schranktrocken)

3 kg

For thin fabrics which are not iron-

ed, e.g. easy care shirts, table linen,

baby clothes, socks, lingerie with

bones or wires.

all

except

TIME (Zeit-

wahl)

IRON DRY (Bügel-

trocken)

3 kg

For thin fabrics which are also to be

ironed, e.g. knitwear, shirts.

all

except

TIME (Zeit-

wahl)

SPECIAL

TIME PROGRAMME

(Zeitprogramm)

8 kg

For drying of individual items of laun-

dry.

all except

SENSITIVE

(Sensitiv)

FRESHEN-UP (Auffri-

schen)

1 kg

For refreshing textiles that have

been in storage.

all except

SENSITIVE

(Sensitiv)

and TIME

(Zeitwahl)

electrolux 7

Programmes

max.

load

(weight

when

dry)

Application/properties Options

Care

mark

BED LINEN (Bettwä-

sche)

3 kg

Bed linen (single and double sheet,

pillowcase, bedspread, duvet cover).

all except

SENSITIVE

(Sensitiv)

and TIME

(Zeitwahl)

EASY IRON PLUS

(Leichtbügeln plus)

1 kg (or 5

shirts)

Special program with anti-crease

mechanism for easy care fabrics

such shirts and blouses; for mini-

mum ironing effort. The results de-

pend on the type of fabric and its fin-

ish. Place fabrics in the dryer

straight after spinning; once dried,

immediately remove fabrics and

place on a clothes hanger.

all

except

SENSITIVE

(Sensitiv)

and TIME

(Zeitwahl)

WOOL (Wolle) 1 kg

For drying woollen fabrics after they

have been washed, using warm air

at minimum mechanical load (Follow

section “Sorting and preparing wash-

ing”). Recommendation: Remove

fabrics immediately after drying, as

no anti-crease programme follows.

The wool drying cycle of this tumble

drying machine has been tested

and approved by The Woolmark

Company. The cycle is suitable to

dry knitted wool garments which are

labelled "hand wash" provided that

the garments are washed in a Wool-

mark endorsed hand washing cycle

and tumble dried according to the in-

structions issued by the manufactur-

er. (M1022)

BUZZER

(Signal) , DE-

LAY START

(Zeitvorwahl)

NIGHT CYCLE (Nacht-

programm) SYNTHET-

ICS (Mischgewebe)

3 kg

For very quiet and gentle drying of

synthetics. Recommend for drying

during the night.

LONG AN-

TI-CREASE

(Knitter-

schutz

Plus) , BUZ-

ZER (Sig-

nal) , DELAY

START

(Zeitvorwahl)

NIGHT CYCLE (Nacht-

programm) COTTON

(Baumwolle)

8 kg

For very quiet and gentle drying of

cotton. Recommend for drying dur-

ing the night.

LONG AN-

TI-CREASE

(Knitter-

schutz

Plus) , BUZ-

ZER (Sig-

nal) , DELAY

START

(Zeitvorwahl)

1) The DELICATE (Schon) and SENSITIVE (Sensitiv) functions cannot be selected together

2) select DELICATE (Schon)

3) set as default

8 electrolux

DAILY USE

Sorting laundry

• Sort by fabric type:

– Cotton/linen for programmes in COT-

TONS (Baumwolle) programme group.

– Mixtures and synthetics for pro-

grammes in SYNTHETICS (Mischge-

webe) programme group.

• Sort by care label: The care labels mean:

Drying in the tumble dryer possible in

principle

Drying at normal temperature

Drying at reduced temperature

Drying in the tumble dryer not possible

Important! Do not place in the appliance

any wet laundry which is not specified on

the care label as being suitable for tumble-

drying.

This appliance can be used for all wet laun-

dry items which are labelled as suitable for

tumble-drying.

• Do not dry new, coloured textiles togeth-

er with light-coloured laundry items. Tex-

tile colours may bleed.

• Do not dry cotton jersey and knitwear

with the EXTRA programme. Items may

shrink!

• Wool and wool-like textiles can be dried

using the WOOL (Wolle) programme. Be-

fore the drying cycle spin the woollen tex-

tiles as well as possible (max. 1200 rpm).

Only dry woollen textiles together of simi-

lar or the same material, colour and

weight. Please dry heavy laundry items

made of wool separately.

Preparing laundry

• To avoid laundry becoming tangled:

close zips, button up duvet covers and

tie loose ties or ribbons (e.g. of aprons).

• Empty pockets. Remove metal items (pa-

per clips, safety pins, etc).

• Turn items with double-layered fabrics in-

side out (e.g. with cotton-lined anoraks,

the cotton layer should be outermost).

These fabrics will then dry better.

Important! Do not overload the appliance.

Observe max. loading volume of 8 kg.

Average laundry weights

bathrobe 1200 g

quilt cover 700 g

man’s work shirt 600 g

man’s pyjamas 500 g

sheet 500 g

tablecloth 250 g

man’s shirt 200 g

night dress 200 g

pillow case 200 g

towelling towel 200 g

blouse 100 g

ladies’ briefs 100 g

men’s underpants 100 g

napkin 100 g

tea cloth 100 g

Switching machine/drum light on

Turn the programme selector to any pro-

gramme or turn it to DRUM LIGHT (Beleuch-

tung) . The machine has been switched on.

When the loading door is opened, the drum

light is illuminated.

Laundry loading

Open loading door:

Use force to push against the loading

door (push point)

2. Load your laundry (do not force it in).

Caution! Do not jam laundry in be-

tween the loading door and rubber seal.

electrolux 9

3. Close loading door securely. Lock must

audibly lock.

Selecting the programme

Use the programme selector to set the pro-

gramme you require. The estimated time to

end of the programme appears on the

LCD, e.g.

( hours . minutes ).

During the cycle, time elapses by steps of

one minute.

DELICATE (Schon) function

654321

For especially gentle drying of sensitive fab-

rics with the

care label and for tempera-

ture-sensitive textiles (e.g. acrylic, viscose).

Programme is executed with reduced heat.

Delicate function is only suitable for use

with loads of up to 3kg.

To activate it:

1. Choose the drying programme.

2. Press DELICATE (Schon) button (1) -

the LED above is on.

To deselect function press again DELICATE

(Schon) button (1). The LED above is off.

SENSITIVE (Sensitiv) function

For gentle drying of fabrics that are frequent-

ly worn. Programme starts on full heat set-

ting, which is then reduced as the pro-

gramme progresses to be kind to the wash-

ing.

To activate it:

1. Choose the drying programme.

2. Press SENSITIVE (Sensitiv) button (2) -

the LED above is on.

To deselect function press again SENSI-

TIVE (Sensitiv) button (2). The LED above is

off.

The DELICATE (Schon) and SENSITIVE

(Sensitiv) functions cannot be selected

together.

LONG ANTI-CREASE (Knitterschutz

Plus) function

This function prolongs anti-crease phase

what gives 90 min. in total. The drum ro-

tates in intervals during this phase. The laun-

dry thereby remains relaxed and free of crea-

ses.

To activate it:

1. Choose the drying programme.

2. Press LONG ANTI-CREASE (Knitter-

schutz Plus) button (3) - the LED above

is on and display shows the following

icon

If this additional function is selected, the anti-

crease phase at the end of the drying cycle

is lengthened by 60 minutes. The laundry

can be removed at any time during the anti-

crease phase.

To deselect function press again LONG AN-

TI-CREASE (Knitterschutz Plus) button. The

LED above is off and 90 from the icon dis-

appears

BUZZER (Signal) function

The appliance is supplied with the BUZZER

(Signal) function deactivated.

The buzzer sounds or plays a tune when ac-

tivated during:

–cycle end

– anti-crease phase and when phase starts

or ends

– cycle interruption by a warning

–alarm

To activate it:

1. Choose the drying programme.

2. Press BUZZER (Signal) button (4) - the

LED above is on.

To deselect function press again BUZZER

(Signal) button (4). The LED above is off.

10 electrolux

TIME (Zeitwahl) function

To select the programme duration after set-

ting the TIME PROGRAMME (Zeitprog-

ramm) . You can select a programme dura-

tion from 10 mins to 3 hrs in 10-minute steps.

1. Turn the programme knob to the TIME

PROGRAMME (Zeitprogramm) . The

blinking 10' appears in the display. (cor-

responding to the cooling phase).

2. Press the TIME (Zeitwahl) button (5) re-

peatedly until the desired programme du-

ration is shown in the display, e.g.

for a programme of 20 minutes.

If the programme duration is not selected,

the duration is automatically set to 10 mins.

DELAY START (Zeitvorwahl)

With the DELAY START (Zeitvor-

wahl) button (7), you can delay the

start of a programme by between

30 minutes (30') and a maximum of

20 hours (20h).

1. Select the programme and additional

functions.

2. Press the DELAY START (Zeitvorwahl)

button (7) as many times as necessary

until the required start delay appears on

the display, e.g.

if the programme

is to be started in 12 hours.

If the display is showing 20h and

you press the button again, the

time delay will be cancelled. The dis-

play will show 0'and then the dura-

tion of the selected programme.

3. To activate the delay timer, press the

START PAUSE (Start / Pause) button

(6). The amount of time remaining until

the programme is set to start is continu-

ously displayed (e.g. 15h, 14h, 13h, …

30' etc).

CHILD LOCK function

The child lock can be set to prevent a pro-

gramme being accidentally started or a pro-

gramme in operation being accidentally

changed. The child lock function locks all

buttons and the programme knob. The

child lock can be activated or deactivated

by holding down the LONG ANTI-CREASE

(Knitterschutz Plus) (3) and BUZZER (Signal)

(4) buttons simultaneously for 5 seconds.

– Before programme is started: Appli-

ance cannot be used

– After programme is started: Pro-

gramme in operation cannot be

changed

The

icon appears in the display to indi-

cate that the child safety device is activated.

The child safety device is not deactivated

once the programme comes to an end.

If you want to set a new programme, you

must first deactivate the child safety device.

Starting the programme

654321

Press the START PAUSE (Start / Pause) but-

ton (6). The programme is started.

The programme phase is shown in LCD by

appropriate icon:

–

- drying phase indication

–

- cooling phase indication

–

- anti-crease phase indication

During program selection all appropriate

phase icons are displayed. When program

is started only current cycle phase is indica-

ted by single icon.

Changing programme

To change a programme which has been se-

lected by mistake once the programme has

started, first turn the programme selector to

OFF (Aus) and then reset the programme.

electrolux 11

The programme can no longer be

changed directly once the programme

has started. If nevertheless there is an

attempt to change the programme on

the programme knob, the programme

progress display and the maintenance

indicators flash. If an option (excluding

the buzzer ) is set, Err appears in the

multidisplay. The drying programme is

not however affected by this (laundry

protection).

Laundry unloading

Once the drying cycle is complete, display

shows a blinking

, anti-crease icon ap-

pears on LCD. If the BUZZER (Signal) but-

ton (4) has been pressed, an acoustic sig-

nal sounds intermittently for about one mi-

nute.

The drying cycles are automatically fol-

lowed by an anti-crease phase which

lasts around 30 minutes. The drum ro-

tates at intervals during this phase. This

keeps the laundry loose and free of crea-

ses. The laundry can be removed at

any time during the anti-crease phase.

(The laundry should be taken out to-

wards the end of the anti-crease phase

at the latest to prevent creases from

forming.) If LONG ANTI-CREASE (Knit-

terschutz Plus)

function has been se-

lected, the anti-crease phase is length-

ened by 60 minutes.

1. Open door.

2. Before removing the laundry, remove

fluff from the micro-fine filter. It is best to

use a damp hand for this purpose. (See

“Care and cleaning” chapter.)

3. Remove laundry.

4. Turn the programme selector to OFF

(Aus) .

Important! After each drying cycle:

- Clean the micro-fine filter and fine filter

- Drain the condensed water container

(See chapter “Care and cleaning”.)

5. Close the door.

CARE AND CLEANING

Cleaning fluff filter

The filters collect all the fluff which accumu-

lates during drying. To ensure that the dryer

works perfectly, the fluff filters (micro-fine fil-

ter and fine strainer) must be cleaned after

every drying cycle.

The warning icon

is on to remind you of

this operation.

Caution! Never operate the dryer

without fluff filters or with damaged or

blocked fluff filters.

Open loading door

2. Use a damp hand to clean the micro-

fine filter, which is built into the lower

part of the loading aperture.

After a period of time, a patina due to

detergent residue on laundry forms on

the filters. When this occurs, clean the

filters with warm water using a brush.

Remove the filter from the door pulling

it out. It can be positioned with the

tooth facing to the left or to the right).

After cleaning do not forget to put it

back.

12 electrolux

Push down unlock button on large

mesh filter.

Large mesh filter jumps up.

Take out fine strainer.

6. Remove fluff from fine strainer. It is best

to use a damp hand for this purpose.

Clean the entire filter area

The strainer area does not have to be

cleaned after every drying cycle, but

should be checked regularly and

cleaned of fluff if necessary.

To do this, grip the top of the large

mesh filter and pull it forwards until it

comes loose from the two brackets.

8. Remove fluff from the entire filter area.

It is best to use a vacuum cleaner for

this purpose.

9. Press both journals of the large mesh fil-

ter into the brackets on the loading

door until they snap into place.

10. Re-insert fine strainer.

11.

Press against the large mesh filter until

it locks into the interlock.

If the fine strainer is not fitted, the large

mesh filter will not snap into place and

the loading door cannot be closed.

Cleaning the door seal

Clean the door seal with a moist cloth imme-

diately after the drying cycle is completed.

Emptying the water reservoir

Empty the water reservoir after every drying

cycle.

electrolux 13

If the water reservoir is full, an active pro-

gramme will break off automatically and the

empty container

icon on the display will

light up. In order to continue the pro-

gramme, the water reservoir must first be

emptied.

Warning! The condensed water is not

suitable for drinking or for preparing

foodstuffs.

Take out water reservoir completely.

Pour condensed water out into a basin

or similar receptacle.

3. Refit water reservoir.

If the programme has been interrupted

as a result of the water reservoir being

full: Press the START PAUSE button to

continue the drying cycle.

The water reservoir has a volume of ap-

prox. 4.5 litres. This is sufficient for

around 8 kg of laundry which has previ-

ously been spun at 1000 revolutions/

minute.

The condensed water can be used as

distilled water, e.g. for steam ironing.

However first filter the condensed wa-

ter (e.g. with a coffee filter) to remove

any residue and small pieces of fluff.

Cleaning heat exchanger

If the heat exchanger

icon is displayed,

the heat exchanger needs to be cleaned.

Caution! Operating when the heat

exchanger is blocked with fluff can

damage the dryer. This also increases

energy consumption.

1. Open door.

Open door in plinth. To do this, press

the release button on the bottom of the

door aperture and open the door in the

plinth to the left.

3. Clean fluff from the inside of the door

and the heat exchanger front chamber.

Wipe the door seal with a damp cloth.

Turn both lock washers inwards.

14 electrolux

Use the handle to pull the heat exchang-

er out of the base and carry it horizontal-

ly to prevent any remaining water from

spilling.

6. To empty the heat exchanger, hold verti-

cally over a washing-up bowl.

Caution! Do not use sharp objects to

clean. The heat exchanger could

develop leaks.

7. Clean heat exchanger.

It is best to use a brush or to rinse thor-

oughly with a hand-held shower.

8. Replace heat exchanger and lock into

place (turn both lock washers outwards

until they snap into place).

9. Close door in plinth.

Caution! Never operate the dryer

without the heat exchanger.

To clean the drum

Caution! Do not use abrasive materials

to clean the drum. Use a soft detergent

to clean the inner side of the drum and

the drum blades.

Keep the inner surface of the drum and

the drum blades clean. The minerals

from the water or cleaning agents can

collect on the inner surface of the

drum. This cause that the laundry is not

sufficient dry.

Clean operating screen and housing

Caution! Do not use furniture cleaners

or aggressive cleaning agents to clean

the appliance.

Use a damp cloth to wipe down the op-

erating screen and housing.

WHAT TO DO IF ...

Troubleshooting by yourself

If, during operation, the error code E... plus

number or letter) appears on the LCD:

Switch the machine off and on again. Reset

programme. Press the START PAUSE

(Start / Pause) button (6). If the error is still

displayed, please inform your local Service

Force Centre and quote the error code.

Problem Possible cause Remedy

Dryer does not work.

Mains plug is not plugged in or

fuse is not working correctly.

Plug in at mains socket. Check

fuse in fuse box (domestic in-

stallation).

Loading door is open. Close loading door.

Have you pressed the START

PAUSE (Start / Pause) button

(6)?

Press the START PAUSE

(Start / Pause) button (6) again.

Drying results unsatisfactory.

Wrong programme selected.

Select a different programme

the next time you dry (see “Pro-

gramme chart” chapter).

Lint filters clogged. Clean lint filters.

Fluff filter clogged. Clean fluff filter.

Heat exchanger clogged with

lint.

Clean heat exchanger.

Overloading of laundry.

Observe recommended loading

volumes.

Ventilation slots in base area

covered up.

Uncover ventilation slots in

base area.

Residue on inside surface of

drum or drum ribs.

Clean inside surface of drum

and drum ribs.

Make an adjustment using the

DRYNESS function (1) (see

chapter ”Daily use”)

electrolux 15

Problem Possible cause Remedy

Conductance of water at instal-

lation site differs from standard

setting of machine.

Re-programme standard set-

ting for degree of drying (see

‘Programming options’ chap-

ter).

Loading door does not close.

Fine strainer not in place and/or

mesh filter not locked in place.

Install fine strainer and/or snap

large mesh filter into place.

When a button is pressed, Err

appears on the LCD.

Washing protection. After the

start of the programme, the op-

tion can no longer be set.

Turn the programme knob to

OFF (Aus) . Set the programme

again.

Drum light does not work.

Programme selector in OFF

(Aus) position.

Turn programme selector to

DRUM LIGHT (Beleuchtung) or

to any programme.

Defective light bulb.

Replace light bulb (see next sec-

tion).

Displayed programme time

changes erratically or stays un-

changed for a long time.

Programme time is corrected

automatically depending on

type and volume of laundry and

level of dampness.

Automatic process; this is not a

machine fault.

Programme inactive, empty wa-

ter reservoir

icon is on.

Water reservoir is full.

Empty the water reservoir, then

start programme with START

PAUSE (Start / Pause) button

(6).

Drying cycle ends shortly after

programme starts.

Not enough washing loaded or

washing loaded is too dry for se-

lected programme.

Select time programme or high-

er drying level (e.g. EXTRA DRY

(Extratrocken) or STRONG DRY

instead of CUPBOARD DRY

(Schranktrocken); ).

Drying cycle lasts an unusually

long time. Note: After around 5

hours the drying cycle ends au-

tomatically (see „Drying cycle

complete ”).

Lint filter clogged. Clean lint filter.

Fluff filter clogged. Clean fluff filter.

Load volume too big. Reduce load volume.

Laundry insufficiently spun.

Laundry must be adequately

spun.

Particularly high room tempera-

ture.

Automatic process, there is no

fault with the appliance. If possi-

ble, lower the room tempera-

ture.

1) only for dryers with DRYNESS function available

Changing the bulb for interior lighting

Only use a special bulb which is designed

specially for dryers. The special bulb can be

obtained from your local service centre.

Important! When the appliance is switched

on, the interior lighting switches itself off

after 4 minutes when the door is open.

Warning! Do not use standard bulbs!

These develop too much heat and may

damage the machine!

Before replacing the bulb, disconnect

the mains plug; with a permanent con-

nection: fully unscrew or deactivate the

fuse.

1. Unscrew cover above the bulb (this can

be found directly behind the loading aper-

ture, at the top; refer to “Description of

machine” section.)

2. Replace defective bulb.

3. Screw cover back down.

Check the correct positioning of o-ring gas-

ket before screwing back the door light cov-

er. Do not operate the dryer when missing o-

ring gasket on door light cover.

16 electrolux

Warning! For safety reasons, the cover

must be screwed down tightly. If this is

not done, the dryer must not be

operated.

TECHNICAL DATA

Height x width x depth 85 x 60 x 58 cm

Drum volume 108 l

Depth with loading door open 109 cm

Height can be adjusted by 1.5 cm

Weight when empty approx. 40 kg

Loading volume (depends on programme)

max. 8 kg

Voltage 220-230 V

Required fuse 10 A

Total power 2350 W

Energy efficiency class B

Energy consumption (8 kg of cotton, pre-drained

at 1000 rpm)

4.48 kWh

Average annual energy consumption 282 kWh

Use Domestic

Permissible ambient temperature + 5°C to + 35°C

Consumption values

The consumption values have been established under standard conditions. They may deviate when

the machine is operated in domestic circumstances.

Programme

Energy consumption in kWh / average dry-

ing time in min.

COTTON CUPBOARD DRY

4.48 / 135 (8 kg load pre-drained at 1000 rpm)

4.3 (8 kg load pre-drained at 1200 rpm)

4.0 (8 kg load pre-drained at 1400 rpm)

3.5 (8 kg load pre-drained at 1800 rpm)

COTTON IRON DRY

3.8 / 108 (8 kg load pre-drained at 1000 rpm)

SYNTHETICS CUPBOARD DRY

1.3 / 45 (3 kg load pre-drained at 1200 rpm)

1) Different loading volume data may be needed in some countries as a result of different measuring methods.

2) in accordance with EN 61121

electrolux 17

MACHINE SETTINGS

Setting Implementation

Buzzer permanent on/off

1. Turn the programme selector to any programme.

2. Press simultaneously the DELICATE (Schon) (1) and

SENSITIVE (Sensitiv) (2) buttons and hold down for ap-

prox. 5 seconds.

– diode above BUZZER (Signal) button (4) starts light-

ing - buzzer permanently on.

– lighting diode comes off - buzzer permanently off.

3. The buzzer is by default always off. You can use the

BUZZER (Signal) button (4) to activate or deactivate

sound but the machine does not memorize your selec-

tion.

Water hardness

Water contains, a variable quanti-

ty of limestone and mineral salts

of which quantities vary according

to geographical locations thus

varying its conductivity values.

Relevant variations of the conduc-

tivity of the water compared to

those prefixed by the factory

could slightly influence the residu-

al humidity of the laundry at the

end of the cycle. Your dryer al-

lows you to regulate the sensitivity

of the drying sensor based on con-

ductivity values of the water.

1. Turn the programme selector to any programme.

2. Press simultaneously the DELICATE (Schon) (1) and

TIME (Zeitwahl) (5) buttons and hold down for approx.

5 seconds. The current setting is on the display:

–

low conductivity <300 μS/cm

–

medium conductivity 300-600 μS/cm

–

high conductivity >600 μS/cm

3. Press the START PAUSE (Start / Pause) button (6) se-

quentially until you set desired level.

4. To memorize setting press simultaneously the DELI-

CATE (Schon) (1) and TIME (Zeitwahl) (5) buttons or

turn knob to OFF (Aus) position

Emptying water tank - warning

message permanent off

When using an external drain for

the condensed water.

1. Turn the programme selector to any programme.

2. Press simultaneously the SENSITIVE (Sensitiv) (2) and

TIME (Zeitwahl) (5) buttons and hold down for approx.

5 seconds.

The current setting is on the display:

–

warning

icon and - warning message is

off

–

warning

icon and - warning message is

switched on

By default the warning message is switched on and

always displayed at the end of the drying cycle or dur-

ing the cycle if the water container is full.

HINTS FOR TEST INSTITUTES

Parameters possible to check by the Test In-

stitutes:

• Energy consumption (corrected with final

humidity) during the cupboard dry cotton

cycle with nominal load.

• Energy consumption (corrected with final

humidity) during the cupboard dry cotton

cycle with half load.

• Final humidity (during cupboard dry cot-

ton, iron dry cotton and cupboard dry

easy care)

• Condensation efficiency (corrected with fi-

nal humidity) during cupboard dry cotton

cycle with nominal and half load

All the cycles have to be checked in accord-

ance with EN 61121 (Tumble dryers for

household use – Methods for measuring

the performance).

18 electrolux

INSTALLATION

Appliance positioning

• It is recommended that, for your conven-

ience, the machine is positioned close to

your washing machine.

• The tumble dryer must be installed in a

clean place, where dirt does not build up.

• Air must be able to circulate freely all

round the appliance. Do not obstruct the

front ventilation grille or the air intake

grilles at the back of the machine.

• To keep vibration and noise to a mini-

mum when the dryer is in use, it should

be placed on a firm, level surface.

• Once in its permanent operating position,

check that the dryer is absolutely level

with the aid of a spirit level. If it is not,

raise or lower the feet until it is.

• The feet must never be removed. Do not

restrict the floor clearance through deep-

pile carpets, strips of wood or similar.

This might cause heat built-up which

would interfere with the operation of the

appliance.

Important!

• The hot air emitted by the tumble dryer

can reach temperatures of up to 60°C.

The appliance must therefore not be in-

stalled on floors which are not resistant to

high temperatures.

• When operating the tumble dryer, the

room temperature must not be lower

than +5°C and higher than +35°C, as it

may affect the performance of the appli-

ance.

• Should the appliance be moved, it must

be transported vertically.

• The appliance must not be installed be-

hind the lockable door, a sliding door a

door with a hinge on the opposite side to

that of the appliance in such a way that a

full opening of the dryer is restricted.

Removing transport safety packaging

Caution!

Before use all parts of the transport packag-

ing must be removed.

1. Open loading door

2. Pull off adhesive strips from inside ma-

chine on top of drum.

3. Remove foil hose and polystyrene pad-

ding from the machine.

Electrical connection

Details on mains voltage, type of current

and the fuses required should be taken

from the type plate. The type plate is fitted

near the loading aperture (see “Product de-

scription” chapter).

Connect the machine to an earthed

socket, in accordance with current wir-

ing regulations.

Warning! The manufacturer

declines any responsibility for

damage or injury through failure to

comply with the above safety

precautions.

Should the appliance power supply

cable need to be replaced, this

must be carried out by our Service

Center.

Warning! The plug must be

accessible after installing the

machine.

Door reversal

Warning! Before changing the door

stop, disconnect the mains plug.

electrolux 19

Open loading door.

Unscrew hinge A from the front of the

machine and take off the loading door.

3. Remove cover plates B . To do this, in-

sert a thin screwdriver into the slots as

shown in the illustration, press down-

wards slightly and pry out the cover

plates.

4. Use an appropriate tool and exert pres-

sure to unfasten locking block C from

the snap-on fixture, take out and re-in-

sert on the other side having rotated

the block through 180°.

Unscrew hinge A from the loading

door, rotate through 180°, re-insert on

the opposite side and screw down.

6. Re-insert cover plates B on the oppo-

site site having first rotated them

through 180°.

Unscrew cover plates D from the front

of the machine, rotate through 180°,

screw on the opposite side.

8. Unscrew door lock E , push down slight-

ly and remove from the front of the ma-

chine.

9. Press snap-in button F in and down,

press cover down slightly and remove

from front of the machine.

10.

Change door lock E over to the oppo-

site side, screw down the door interlock.

11. On the other side, insert cover F and al-

low snap-in button to lock into place.

12. Insert loading door and hinges into re-

cesses on the front of the machine and

screw down.

Note regarding contact protection: The

machine is only secure for operations again

once all plastic parts have been inserted.

Special accessories

• stack kit

Available from your Service Force Cen-

tre or your specialist dealer

These intermediate installation kits can

be used to arrange the dryer and an wash-

ing machine (60 cm wide, front loaded)

as a space-saving washer/dryer stack.

The washing machine is at the bottom

and the dryer is at the top.

Read carefully the instructions supplied

with the kit.

•

drain kit

Available from your Service Force Cen-

tre or your specialist dealer

Installation kit for direct draining of con-

densate into a basin, siphon, gully, etc.

The condensate tank then no longer has

to be drained, it must however remain in

its intended position in the machine.

Read carefully the instructions supplied

with the kit.

•

pedestal with the drawer

Available from your Service Force Cen-

tre or your specialist dealer

To situate the dryer in optimal high and

have some additional space to store (e.g.

laundry).

Read carefully the instructions supplied

with the kit.

SERVICE

If there are technical faults, first check if you

can remedy the problem yourself with the

help of the operating instructions - see chap-

ter What to do if….

If you cannot remedy the problem on your

own, get in touch with the Customer Care

Department or one of our service partners.

To assist you quickly, these data are neces-

sary:

– Model description

– Product number (PNC)

– Serial number (S No. is on rating plate

stuck to the product - to find it see chapter

Product description ))

– Type of failure

– Any error messages shown by the display.

20 electrolux

La pagina sta caricando ...

Electrolux TKGL5E101 Manuale utente

Marca: Electrolux

Modello: TKGL5E101

Categoria: Asciugatrici

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: Electrolux TKGL5E101 User manual

Electrolux TKGL5E101 Manuale utente

Electrolux TKGL5E101 Manuale utente

in altre lingue

Documenti correlati

Altri documenti