Weller WSF 80 Istruzioni per l'uso

WSF 80
Weller
Marca
Weller
Modello
WSF 80
Categoria
Saldatori
Tipo
Istruzioni per l'uso
WSF 80
Thermo-regulated soldering iron gun with manual solder wire feed.
Technical data:
Voltage supply: 230 V 50 and 60 Hz
Max power: 80W
Power regulation: PWM from 0 to 100%
Max temperature: 550°C @ 100%
Cable: 3 x 0.75 H03 Schuko male connector
Weight: 320 gr.
Consist of:
• WSF 80
• 6 gr. Lead-free wire SACX0307 1mm coil
• WB 10 1mm and WB 15 1.5mm wire-guide
pipe
• 2mm EX key
• Empty spare coil
• SF25 2,5 sqmm
INSTRUCTIONS
Choose a tube guide wire 1 or 1.5 mm suitable for w SnPb alloys give 1mm min, max
1.5 mm).
Insert the end of the wire, perfectly straight, into t e gun holding down the lever until the soldering
p, (check the correct insertion through the windo
e orientation of the wire to the tip, act on the
urve Tips Tubetti guidafilo Max Temperature
ire diameter (use lead-free or
he rear hole of th
w). ti
Adjust the pre-load on the external spring acting on the knob, it is recommended to exercise the minimum
pressure to avoid the deformation of the wire.
If the wire blocks, holding down the lever and pull it out, after cutting the deformed part, proceed to a new post.
Connect the tool to the mains (230V ~) the indicator begins to flash.
TIN THE TIP AS SOON AS THE MELTING TEMPERATURE IS REACHED
Pushing the trigger, the wire advances toward the tip, for a length adjustable from 1 to 6 mm. To adjust the amount
f wire needed, act on the grain, in front of the trigger; for adjusting tho
grain beneath the thread guide
.
Model Longlife c
WSF 80 80W-230V~ SF25
384899
SF10(Ø1.0) T0051384999
SF15(1.6) T0051385099
SF25(2.5) T0051385199
85299
TB/70/10 Ø 1.0 T0051385399
TB/70/15 Ø 1.5 T0051385499
100% = 550°C
T0051
SF40(4.0) T00513
READ THE FO
LLOWING IMP N REGARDING THE SAFETY USE OF THE DEVICE
Before connecting the appli nameplate data corresponds with the mains.
This appliance must only be used for the purpose it was designed.
Do not touch the appliance with wet hands and / or feet are wet.
Do not pull the cord or the appliance itself to remove the plug from the socket.
Before performing any maintenance, disconnect the appliance from the mains and allow to cool.
Do not use non-standard extensions (IMQ-VDE-NF-ETC..)
This tool can be placed on a holder when not in use
WARRANTY
Weller warrants this product against defects in workmanship for one year from date of purchase documented, in
case of absence of such documentation will be considered the date of manufacture.
The warranty excludes all parts subject to wear.
The warranty is void in case of tampering or improper use of the device.
Transport costs are paid by the customer.
ORTANT INFORMATIO
ance make sure that the
2
DECLARATION CE OF CONFORMITY
otto:
Brand: WELLER
odel: WSF 80 80W 230Vac
DICHIARAZIONE DI CONFORMITA’ CE
WELLER
Dichiara sotto la sua esclusiva responsabilità che il prod
Hereby declares under his own responsibility that the product:
Tipo -Type: gun type soldering iron Marchio -
Modello - M
é di fabbricazione Italiana CEE - Is made in Italy CEE
é conforme alle seguenti norme: Complies with the following regulations:
• 2006/95/CE – DIRETTIVA BASSA TENSIONE
2006/95/CE – LOW VOLTAGE DIRECTIVE
• 2004/108/CE – DIRETTIVA COMPATIBILITA’ ELETTROMAGNETICA (EMC)
2004/108/CE – ELECTROMAGNETIC COMPATIBILITY DIRECTIVE (EMC)
• 2002/96/CE – DIRETTIVA SUI RIFIUTI DI APPARECCHIATURE ELETTRICHE ED ELETTRONICHE (RAEE)
2002/96/CE – WASTE ELECTRICAL AND ELECTRONICAL EQUIPMENT DIRECTIVE (WEEE)
base a quanto previsto dalla Direttiva:
r
icly in accordance with the requirements of the Directive:
• 2006/42/CE – DIRETTIVA COMUNITARIA SULLE MACCHINE
2006/42/CE - COUNCIL DIRECTIVE ON MACHINERY
www.weller-tools.com
Amministratore
Director
Date: 01 May 2012
  • Page 1 1
  • Page 2 2

Weller WSF 80 Istruzioni per l'uso

WSF 80
Weller
Marca
Weller
Modello
WSF 80
Categoria
Saldatori
Tipo
Istruzioni per l'uso
Scarica il pdf
rapporto

in altre lingue

Documenti correlati