Shindaiwa AH236S-LW Manuale utente

1????

OPERATOR'S MANUAL

MANUEL D'UTILISATION

BEDIENUNGSANLEITUNG

MANUALE PER L'OPERATORE

MANUAL DE INSTRUCCIONES

AH236S-LW

ENGLISH

FRANÇAIS

DEUTSCH

ITALIANO

ESPAÑOL

WARNING

READ THE INSTRUCTIONS CAREFULLY AND FOLLOW THE RULES FOR

SAFE OPERATION.

FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY.

AVERTISSEMENT

LIRE ATTENTIVEMENT LES INSTRUCTIONS ET SUIVRE LES RÈGLES DE

SECURITÉ.LE NON-RESPECT DES RÈGLES DE SÉCURITÉ ENTRAÎNE UN

RISQUE DE BLESSURE GRAVE.

WARNUNG

LESEN SIE DIE BEDIENUNGSANLEITUNG SORGFÄLTIG DURCH, UND

BEFOLGEN SIE DIE SICHERHEITSREGELN. ANDERNFALLS BESTEHT DAS

RISIKO SCHWERER VERLETZUNGEN.

AVVERTENZA

LEGGERE E SEGUIRE ATTENTAMENTE LE ISTRUZIONI PER LAVORARE IN

CONDIZIONI DI MASSIMA SICUREZZA. LA MANCATA OSSERVANZA DELLE

ISTRUZIONI POTREBBE PROVOCARE LESIONI GRAVI.

ADVERTENCIA

LEA ATENTAMENTE LAS INSTRUCCIONES Y SIGA LAS INDICACIONES

PARA UN FUNCIONAMIENTO SEGURO. DE NO HACERLO, PODRÍA SUFRIR

LESIONES GRAVES.

??

1Top cover

ENGLISH

(Original instructions)

OPERATOR'S MANUAL

ARTICULATED HEDGE TRIMMER

AH236S-LW

WARNING

READ THE INSTRUCTIONS CAREFULLY AND FOLLOW THE

RULES FOR SAFE OPERATION.

FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY.

2

Important information

2Important information

Please ensure that you read the operator's manual before using your product.

Intended use of this product

shindaiwa Hedge Trimmer are lightweight, high-performance, petrol engined units designed for hedge and shrub trim-

ming.

Do not use this unit for any purpose other than aforementioned.

Users of the product

You should not use this product until you have read the operator's manual carefully and fully absorbed its content.

This product should not be used by anyone who has failed to read the operator's manual properly, is suffering from a

cold, tiredness or otherwise in poor physical condition, or children.

Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their prop-

erty.

About your operator's manual

This manual contains necessary information about the operation and maintenance of your product. Please read it care-

fully and absorb its contents.

Always keep your manual in a place where it is readily accessible.

If you have lost your manual or it is damaged and no longer readable, please purchase a new one from your shindaiwa

dealer.

The units used in this manual are SI units (International System of Units). Figures in parentheses are reference values,

and there may be a slight conversion error in some cases.

Loaning or assigning your product

When loaning the product described in this manual to another party, ensure that the person borrowing and working with

the product receives the operator's manual along with the product. If you assign your product to another party, please

enclose the operator's manual with the product when handing it over.

Enquiries

Please contact your shindaiwa dealer for requests regarding information about your product, the purchase of consum-

ables, repairs, and other such enquiries.

Notices

The content of this manual may be changed without notice for the purpose of upgrades to the product. Some of the

illustrations used may differ from the product itself in order to make the explanations clearer.

This product requires the assembly of some parts.

Please consult your shindaiwa dealer if anything is unclear or of concern.

Feature of this model: Soft Start

Soft Start generates enough revolving power to rotate crankshaft up to a speed to ignite the engine and bring almost

no kickback. Soft Start makes engine start far easier than you ever expect.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a re-

placement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are

also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not

amount to a major failure.

For warranty service, find the nearest Authorised Service Dealer in our dealer locator map at www.echo australia.com.au/

en_au/finder, or by calling 1300 274 447, or by emailing or writing to salesenquires@briggsandstratton.com.au, Briggs &

Stratton Australia Pty Ltd, Locked bag 5004, St Clair, NSW 2759.

3

Contents

For safe use of your product............................................................................................... 4

Warning notices............................................................................................................. 4

Other indicators ............................................................................................................. 4

Symbols.........................................................................................................................4

Location in which the safety decal is attached............................................................... 6

Handling fuel.................................................................................................................. 7

Handling the engine....................................................................................................... 7

Handling the product ..................................................................................................... 9

Packing list........................................................................................................................ 13

Description........................................................................................................................ 14

Before you start ................................................................................................................15

Assembly ..................................................................................................................... 15

Adjusting Cutting Angle ............................................................................................... 17

Shoulder strap ............................................................................................................. 18

Preparing the fuel ........................................................................................................ 19

Engine operation............................................................................................................... 20

Starting the engine ...................................................................................................... 20

Stopping the engine..................................................................................................... 21

Hedge and shrub trimming operation ............................................................................... 22

Basic hedge trimming operation .................................................................................. 22

Maintenance and care ...................................................................................................... 23

Maintenance and care ................................................................................................. 23

Storage ............................................................................................................................. 29

Long-term storage (30 days or more).......................................................................... 29

Disposal procedure........................................................................................................... 30

Specifications.................................................................................................................... 31

Declaration of conformity .................................................................................................. 32

4

For safe use of your product

For safe use of you r product

Be careful to read this section before using your product.

The precautions described in this section contain important safety information. Please observe them carefully.

You must also read the precautions that appear in the body of the manual itself.

Text following a [diamond mark] mark describes the potential consequences of failing to observe the precaution.

Warning notices

Situations where there is a risk of physical injury to the operator and other people are indicated in this manual and on the product

itself by the following warning notices. Always read and observe them carefully in order to ensure safe operation.

Other indicators

As well as warning notices, this manual uses the following explanatory symbols:

Symbols

In this manual and on the product itself, a series of explanatory symbols is used. Please make sure that you fully understand what

each symbol means.

DANGER WARNING CAUTION

This symbol accompanied by the

word "DANGER" calls attentions to

an act or a condition which will lead to

serious personal injury or death of op-

erators and bystanders.

This symbol accompanied by the

word "WARNING" calls attentions to

an act or a condition which can lead to

serious personal injury or death of op-

erators and bystanders.

"CAUTION" indicates a potentially

hazardous situation which, if not

avoided, may result in minor or mod-

erate injury.

Circle and slash sym-

bol means whatever is

shown is prohibited.

NOTE IMPORTANT

This enclosed message provides tips

for use, care and maintenance of the

product.

Framed text featuring the word "IM-

PORTANT" contains important infor-

mation about the use, checking,

maintenance and storage of the prod-

uct described in this manual.

Symbol form/shape Symbol description/applica-

tion

Symbol form/shape Symbol description/applica-

tion

Carefully read the operator's

manual Petrol and oil mixture

Wear eyes, ears and head

protection Purge bulb (Primer)

Safety / Alert Finger severing

Emergency stop Carburettor adjustment

- Idle speed

Do not use the product in plac-

es with poor ventilation

Choke Control

"Cold Start"

Position

(Choke Closed)

5

For safe use of your product

Beware of fire

Choke Control

"Run"

Position

(Choke Open)

Beware of electric shocks Environmental protection!

Beware of high-temperature

areas

Guaranteed sound power lev-

el

Engine start

This product conducts elec-

tricity. Keep the product and/

or operator a minimum dis-

tance of 10 meters away from

electrical source and power

lines.

Wear heavy duty, non-slip

gloves.

Safety tip shoes or boots with

non-slip sole should be worn.

Keep bystanders at least 15

meters away from the operat-

ing trimmer to reduce the risk

of being struck by falling ob-

jects or thrown debris.

Be aware of the danger of fall-

ing debris.

Symbol form/shape Symbol description/applica-

tion

Symbol form/shape Symbol description/applica-

tion

6

For safe use of your product

Location in which the safety decal is attached

The safety decal shown below has been attached to the products described in this manual. Ensure that you understand what

the decal means before using your product.

If the decal becomes unreadable due to wear and tear or damage, or peels off and is lost, please purchase a replacement decal

from your dealer and attach it in the location shown in the illustrations below. Ensure that the decal is readable at all times.

1. Safety decal (Part number X505-002890)

7

For safe use of your product

Handling fuel

Handling the engine

DANGER

Always keep well away from fire when refuelling

Fuel is highly inflammable and leads to a risk of fire if mishandled. Use extreme care when mixing, storing or handling

or serious personal injury may result. Be careful to observe the following instructions.

Do not smoke or hold a flame near when refuelling.

Do not fuel up while the engine is hot or in operation.

If you do so, the fuel could ignite and cause fire, leading to burns.

About the container and refuelling place

Use an approved fuel container.

Fuel tanks/cans may be under pressure.

Always loosen fuel caps slowly allowing pressure to

equalize.

DO NOT fill fuel tanks indoors.

ALWAYS fill fuel tanks outdoors over bare ground.

Fuel spills can cause fire

Observe the following precautions when refuelling:

Do not add so much fuel that it reaches the mouth of the

fuel tank. Keep the fuel within the prescribed level (up to

the shoulder level of the fuel tank).

Mop up any fuel that overflows or spills out due to over-

filling.

Tighten the fuel tank cap securely after refuelling.

Fuel spills can cause fire and burns when ignited.

1. Fuel tank

2. Shoulder level

Do not start the engine in the area where you refue-

led

You must not start the engine in the place where you

carried out the refuelling. Move at least 3m from the

place where you refueled before starting the engine.

Fuel leaks that occur while refuel-

ling can cause fire if ignited.

Fuel leaks cause fire

After refuelling, always check

that there are no leaks or dis-

charges of fuel from the fuel

pipe, fuel system grommets, or

around the fuel tank cap.

If you do find fuel leaks or discharges, stop using the

product immediately and contact your dealer to have it

repaired.

Any fuel leaks could cause fire.

DANGER

Keep the trimmer at least 10 meters away from electrical lines or branches that contact electrical lines

The articulated hedge trimmer is not insulated against electrical shock. Keep the trimmer at least 10 meters away from

electrical lines or branches that contact electrical lines.

Approaching or contacting electrical lines with the trimmer could cause death or serious injury.

8

For safe use of your product

WARNING

Starting the engine

Be particularly careful to observe the following precau-

tions when starting the engine:

Always ensure all handles and guards are fitted

Check that none of the nuts and bolts are loose

Check that there are no fuel leaks

Check that the cutter blades is not damaged or exces-

sively worn. If you find any abnormalities, do not use

the product.

Place the product in a flat, well ventilated place

Leave plenty of space around the product and do not al-

low people or animals near it

Remove obstructions, if any

Make sure that the cutter blades is not touching the

ground or any obstacles

Start the engine with the throttle trigger in the idle speed

position

Hold the product firmly to the ground when starting the

engine

Do not start the engine holding the product in the air

Failure to observe the precautions could cause an accident

or injury, or even lead to a fatality.

Once the engine has started, check for abnormal vi-

brations and sounds

Check that there are no abnormal vibrations or sounds

once the engine starts. Do not use the product if there

are abnormal vibrations or sounds. Contact your dealer

to have it repaired.

Accidents involving parts that fall or shatter off can cause

wounds or serious injury.

Do not touch high temperature or high voltage com-

ponents while the product is running

Do not touch the following high temperature or high volt-

age components while the product is running or for some

time after it stops.

Silencer, spark plug, gear housing, and

other high temperature components

You could burn yourself if you touch a high

temperature component.

Spark plug, spark plug wire, and other

high voltage components

You could receive an electric shock if you

touch a high voltage component while the

product is running.

Put safety first in the case of fire or smoke

If fire comes from the engine or smoke appears from

any area other than the exhaust vent, first distance

yourself from the product to ensure your physical safe-

ty.

Use a shovel to throw sand or other such

material on the fire to prevent it from

spreading, or put it out with a fire extin-

guisher.

A panicked reaction could result in the fire and

other damage becoming more extensive.

Exhaust fumes are toxic

The exhaust fumes from the engine contain toxic gases.

Do not operate the product indoors or in a plastic green-

house or in other ill ventilated places.

The exhaust fumes could cause poisoning.

Turn off the engine when checking or maintaining

the product

Observe the following precautions when checking and

maintaining your product after use:

Turn the engine off and do not attempt to check or main-

tain the product until the engine has cooled

You could burn yourself.

Remove the spark plug cap before performing checks

and maintenance

An accident could occur if the product starts unexpectedly.

Checking the spark plug

Observe the following precautions when checking the

spark plug.

If the electrodes or terminals are worn, or if there are

cracks in the ceramics, replace them with new parts.

The spark test (for checking whether the spark plug is

sparking) must be carried out by your dealer.

The spark test must not be carried out in proximity of

the spark plug hole.

The spark test must not be performed in places where

there are fuel spills or inflammable gases

You must not touch the

metal parts of the spark

plug

The spark plug could ig-

nite a fire or give you an

electric shock.

9

For safe use of your product

Handling the product

General precautions

Precautions for use

WARNING

Operator's manual

Be careful to read the operator's manual

properly before using your product in or-

der to ensure correct operation.

Failure to do so could lead to an accident or

serious injury.

Do not use the product for anything

other than its intended purpose

You must not use the product for any purpose other

than those described in the operator's manual.

To do so could lead to an accident or serious injury.

Do not modify the product

You must not modify the product.

To do so could lead to an accident or serious injury. Any

malfunction resulting from a modification to the product will

not be covered by the manufacturer's warranty.

Do not use the product unless it has been checked

and maintained

You must not use the product unless it has been

checked and maintained. Always ensure that the prod-

uct is checked and maintained on a regular basis.

Failure to do so could lead to an accident or serious injury.

Loaning or assigning your product

When loaning your product to another party, ensure

that the person borrowing the product receives the op-

erator's manual along with it.

If you assign your product to another party, please en-

close the operator's manual with the product when

handing it over.

Failure to do so could lead to an accident or serious injury.

Being prepared in case of an injury

In the unlikely event of an accident or injury, please ensure

that you are prepared.

First aid kit

Towels and wipes (to stop any bleeding)

Whistle or mobile phone (for calling outside help)

If you are unable to perform first aid or call for outside help,

the injury could worsen.

DANGER

Always stop the engine when a blades jam occurs

Do not attempt to remove an object causing a blades jam if the engine is running.

Physical injury can occur if a blades jam is removed and the blades starts moving.

10

For safe use of your product

WARNING

Users of the product

The product should not be used by:

people who are tired

people who have taken alcohol

people who are on medication

people who are pregnant

people who are in poor physical

condition

people who have not read the op-

erator's manual

children

Failure to observe these instruc-

tions could lead to an accident.

The ignition system of this product generates electro-

magnetic fields during operation. Magnetic fields can

cause pacemaker interference or pacemaker failure. To

reduce health risks, we recommend that pacemaker us-

ers consult their physician and the pacemaker manu-

facturer before operating this product.

Environment of use and operation

Do not use the product in places where there is no sure

foothold, such as on steep slopes or after rainfall, as

such places are slippery and dangerous.

Maintain footing and balance at all times. Do not stand

on slippery, uneven or unstable surfaces. Do not work

in odd positions or on ladders. Do not over reach.

Do not operate the product at night or in dark places

with poor visibility.

Heavy protective clothing can increase operator fatigue

which may lead to heat stroke. Schedule heavy work for

early morning or late afternoon hours when tempera-

tures are cooler.

When cutting a branch that is under tension, be alert for

spring-back so that you will not be struck by the moving

branch.

A serious injury could result if you fall or slip, or fail to oper-

ate the product correctly.

Transport of the product

When transporting in the situations described below, turn

off the engine and ensure that the cutter blades has

stopped moving, then fit the blade cover and position the

silencer away from yourself.

Moving to the place where you are working

Moving to another area while you are working

Leaving the place where you have been working

Failure to observe these precautions could cause burns or

serious injury.

When transporting the product by car, empty the fuel

tank, fit the blade cover, and secure the product firmly

in place to prevent it from moving around.

When carrying the articulated hedge trimmer by hand,

the cutter attachment should be pointing backward with

the cutter blade in the retracted or transporting posi-

tion.

Travelling by car with fuel in the fuel tank could lead to a fire.

Vibration and cold

It is believed that a condition called Raynaud's Phenome-

non which affects the fingers of certain individuals may be

brought about by exposure to vibration and cold. Expo-

sure to vibration and cold may cause tingling and burning,

followed by loss of colour and numbness in the fingers.

The following precautions are strongly recommended be-

cause the minimum exposure which might trigger the ail-

ment is unknown.

Keep your body warm, especially the head and neck,

feet and ankles, and hands and wrists.

Maintain good blood circulation by performing vigorous

arm exercises during frequent work breaks, and also by

not smoking.

Limit the number of hours of operation.

Try to fill each day with jobs where operating the hedge

trimmer or other hand-held power equipment is not re-

quired.

If you experience discomfort redness and swelling of

the fingers, followed by whitening and loss of feeling,

consult your physician before exposing yourself further

to cold and vibration.

Failure to observe these instructions could result in damage

to your health.

Repetitive stress injuries

It is believed that over-using the muscles and tendons of

the fingers, hands, arms and shoulders may cause sore-

ness, swelling, numbness, weakness and extreme pain to

the areas just mentioned. Certain repetitive hand activities

may put you at a high risk for developing a repetitive

stress injury (RSI).

To reduce the risk of RSI, do the following:

Avoid using your wrist in a bent, extended or twisted

position.

Take periodic breaks to minimize repetition and rest

your hands. Reduce the speed and force in which you

do the repetitive movement.

Do exercises to strengthen hand and arm muscles.

See a doctor if you feel tingling, numbness or pain in

your fingers, hands, wrists or arms. The sooner RSI is

diagnosed, the more likely permanent nerve and muscle

damage can be prevented.

Failure to observe these instructions could result in damage

to your health.

11

For safe use of your product

WARNING

Remove foreign objects and obstructions before

working with the product

Inspect area that the product will be used in. Remove

stones, metal objects and any other object that could

jam or damage the product.

An accident or serious injury can occur if foreign objects

throw the cutting device.

Turn off the engine immediately if anything goes

wrong

In the following situations, turn off the engine immediately

and ensure that the cutting device has stopped before

checking each area of the product. Replace any damaged

parts.

If the cutting device hits a rock, tree, post, or other such

obstruction while you work.

If the product suddenly starts to vibrate abnormally.

Continuing to use parts when they are damaged could lead

to an accident or serious injury.

The area within a 15 m radius is a danger zone

The area within a 15 m radius of the product is a danger

zone. Be careful to observe the following precautions

while working with the product.

Do not allow children and other people or pets to enter

the danger zone.

If another person enters the danger zone, turn off the

engine to stop the blades.

When approaching the operator, signal to him by, for

example, throwing twigs from outside the danger zone,

and then check that engine has been switched off and

the blades has stopped moving.

Do not allow anyone to hold the material you are cut-

ting.

Any contact with the cutter blades could cause serious inju-

ry.

Do not use the product when the cutter blades is

moving at idle speed

You must not use the product while the cutter blades is

moving if the Hedge Trimmer is running with the throttle

trigger in the idle speed position. Turn off the engine im-

mediately and adjust the carburettor.

To do so could lead to an accident or serious injury.

Operation

Never remove hands from the product when the blades

are moving.

Only adjust cutting angle with unit resting flat on the

ground, with the switch in the "STOP" position. Never

adjust blade angle while standing.

Failure to observe these instructions will cause the product

to be held unsteadily and could result in serious injury.

Make sure that the cutter blades is stopped before

putting the product on the ground

When you turn off the engine, check to ensure the cutter

blades has stopped moving before you lower the prod-

uct to the ground.

Even if the engine has been turned off, the blades can still

cause an injury while free-wheeling.

Remove debris from the silencer

If objects such as grasses, leaves, twigs or excessive

grease got stuck over the area around the silencer of

the engine, stop the engine and remove them paying at-

tention not to touch hot spots.

Failure to do so could lead to a fire.

WARNING

Do not use the product to cut hard objects

Do not use the product to cut hard objects such as

wires or steel plates.

If the blades strikes an obstruction or is prevented from

functioning properly, stop the engine and inspect the

blades for damage.

Failure to follow these instructions could cause breakage of

the product or an accident.

Never use the product getting on a ladder or a stool

Do not overreach or stand on unstable surfaces.

Do not use the product when being at the top of the lad-

der or standing on a stool.

Failure to do so could lead to an accident or serious injury.

12

For safe use of your product

Protective gear

WARNING

Wear protective gear

Always wear the following protective gear when working

with the hedge trimmer.

a Head protection (helmet): Protects the head

b Ear muffs or ear plugs: Protect the hearing

c Safety goggles: Protect the eyes

d Safety gloves: Protect the hands from cold and vibration

e Work clothes that fit (long sleeves, long trousers): Pro-

tect the body

f Heavy duty, non-slip protective boots or non-slip work

shoes : Protect the feet

Failure to observe these precautions could result in damage

to your sight or hearing, or lead to a serious injury.

When necessary, please use the protective gear below.

Dust mask: Protects the breathing apparatus

Bee net: To deal with attacks by bees

Full face shield: When trimming overhead, wear head pro-

tection meeting CE with a full face shield.

Wear proper clothing

Do not wear ties, jewellery, or loose, dangling clothing which could be

caught in the unit. Do not wear open toed footwear, or go bare-foot or

barelegged.

Failure to observe these precautions could result in damage to your sight or

hearing, or lead to a serious injury.

13

Packing list

The following parts are packed separately in the packing box.

When you have unpacked the box, please check the parts that it contains.

Contact your dealer if anything is missing or broken.

1. Power head

2. Operation shaft

3. Blade cover

4. Shoulder strap

5. L-wrench

6. Spanner

7. Socket wrench

8. Operator's manual

14

Description

Descript ion

1. Ignition switch Device for allowing the engine to be

started and stopped.

2. Throttle trigger lockout Device that prevents the acci-

dental operation of the throttle trigger until manually re-

leased.

3. Spark plug

4. Air cleaner cover Covers air filter.

5. Fuel tank cap For closing the fuel tank.

6. Fuel tank Contains fuel and fuel filter.

7. Throttle trigger Device activated by the operator's fin-

ger, for controlling the engine speed.

8. Front grip

9. Hand guard Guard between the front handle and cut-

ting device for protecting the hand from injuries if the

hand slips off the handle.

10. Outer tube Part of the unit that provides a casing for

power transmission shaft.

11. Cutter assembly adjustment lever Provides secure

hand grip for adjusting cutting blade angle.

12. Hedge trimmer cutter assembly

13. Latch lock Fixes the angle of the cutter.

14. Latch release Safety device to prevent the latch lock

from being released unexpectedly.

15. Knob Releases the rotation regulation when it is pulled.

16. Gear housing assembly Gear housing contains drive

gears for transmitting power to cutting blades.

17. Cutter bar and cutter blades That part of the assembly

of cutter blade and shear plate together with any sup-

porting part, which performs the cutting action.

18. Blunt extension An extending blunt part of the cutting

device.

19. Blade cover When transporting or storing the product

always fit the blade cover.

20. Suspension point Device on which the strap can be

hooked.

21. Shoulder strap An adjustable strap to suspend unit.

22. Starter handle Pull handle to start the engine.

23. Type and serial number

15

Before you start

Assembly

Connect the outer tube to the powerhead

1. Place the powerhead on a clean, flat surface, spark plug fac-

ing up.

2. Slip off the protective cover from the end of the outer tube.

3. Use the L-wrench to loosen the tube clamp screw.

4. Slide the outer tube into the tube clamp until the tube bot-

toms. If installation is difficult, rotate the outer tube or main

shaft slightly until you feel the drive shaft splines engage with

the powerhead.

5. Position the outer tube so that the gearcase output shaft is

facing left on silencer cover.

6. Slide the outer tube into the powerhead until the throttle grip

just contacts the tube clamp.

7. Tighten the clamp screw firmly.

Connect the throttle cable

1. Loosen the air cleaner cover knob and remove the air clean-

er cover.

WARNING

Read the operator's manual carefully to ensure that you assemble the product correctly.

Using a product that has been incorrectly assembled could lead to an accident or serious injury.

1. Spark plug

2. Clamp screw

3. Tube clamp

4. Drive shaft

5. Outer tube

6. Protective cover

WARNING

Ensure that the fuel tank cap is securely in place.

Failure to do so could lead to an injury or serious accident,

or cause a fire.

1. L-wrench

2. Tube clamp

CAUTION

Do not force the shaft tube into the powerhead.

Excessive force can damage the shaft tube and drive shaft.

1. Air cleaner cover

2. Air cleaner cover knob

16

Before you start

2. Place throttle cable into adjustment fixture and install wire

end into large carburettor throttle swivel hole.

3. The throttle lever free play should be approximately 4-6 mm.

4. Turn the adjustment nut in or out as required to obtain proper

free play 4-6 mm.

5. Make sure that the throttle lever operates smoothly without

binding.

6. Check throttle for freedom of movement and that wide open

throttle / low idle extremes are adjusted properly.

7. Tighten locknut.

8. Connect 2 ignition leads from throttle cable tubing to 2 igni-

tion leads on engine.

9. Secure ignition leads against engine with clips.

10. Install air cleaner cover.

1. Throttle cable

2. Adjustment fixture

3. Throttle swivel hole

4. Adjustment nut

5. Locknut

1. Ignition leads

2. Clip

3. Clip

CAUTION

Wiring runs must not interfere with throttle operation.

17

Before you start

Adjusting Cutting Angle

Adjusting the hedge trimmer cutter assembly

1. Position the hedge trimmer on a flat, level surface with the

engine resting on the fuel tank guard. Make sure the blade

cover is in place on the blade.

2. Pull the tip of hand guard, and remove the cutter assembly.

3. With your right hand, grasp the outer tube near the handle.

With your left hand, grip the adjustment lever on the cutter

assembly. With the index finger of your left hand, press the

latch release. With your left thumb, press the latch lock.

4. While holding the latch release down, pivot the cutter assem-

bly using the adjustment lever until it is at the desired cutting

angle.

5. Release the latch lock and the latch release. Make sure the

latch lock and the latch release return securely to the straight

ahead position.

6. Remove the blade cover from the cutter blade. The engine

now may be started.

DANGER

Never adjust cutting assembly with engine running.

Failure to do so could lead to an injury or serious accident.

WARNING

Hedge trimmer blades are sharp. Always wear gloves when adjusting cutting assembly.

Wear heavy duty gloves when working with the hedge trimmer blades. When replacing the hedge trimmer blades

during a trimming task, ensure that the engine is switched off and that the blades have stopped.

Do not stand hedge trimmer on end when adjusting cutting angle, otherwise serious injury may result.

Gear case assembly becomes HOT during use. Always grip assembly at blade-adjustment handle when making cut-

ting angle adjustments, otherwise serious injury may result.

Failure to do so could lead to an injury or serious accident.

1. Cutter assembly

2. Hand guard

1. Adjustment lever

2. Latch release

1. Latch lock

1. Adjustment lever

IMPORTANT

The latch release provides an interlock to help prevent inad-

vertent depression of the latch lock.

18

Before you start

Cutter assembly position

The cutter assembly can be adjusted to ten different positions

ranging from 135° to 270° from the outer tube as shown. Al-

ways make sure the lock latch is securely locked after each

adjustment.

Adjusting for Storage or Transportation

1. With the engine off, install the blade cover onto the blade.

2. Rotate the cutter assembly so it is parallel to the tube. The

rotation is restricted at the position of 135° by the lock pin.

Pull the knob and release the lock pin.

3. Make sure the latch lock and the latch release return secure-

ly to a locking position.

4. Fit the tip of the cutter assembly into the storage position of

the hand guard and fix it.

5. Make sure the blade cover is in place on the cutters before

storing or transporting.

Shoulder strap

1. Hook the strap hook to the hanger on the outer tube.

2. Wear the shoulder strap so that the hook stays at your right

hand side.

3. Adjust the length of the shoulder strap so that you can hold

and operate the machine comfortably.

Emergency Release

∗In case of emergency, strongly pull the white tab at the hook.

The machine will be released from the strap.

1. Knob

1. Support notch

2. Blade cover

WARNING

Never run the engine when adjusting the cutter assem-

bly to the storage position.

IMPORTANT

Adjust the shoulder strap or harness so the shoulder pad rests

comfortably on the off-side shoulder. Make sure all hooks and

adjustment devices are secure.

La pagina si sta caricando...

Shindaiwa AH236S-LW Manuale utente

Shindaiwa AH236S-LW Manuale utente

in altre lingue

Documenti correlati