Shindaiwa AH236S-LW Manuale utente

Categoria
Tagliasiepi a motore
Tipo
Manuale utente
1????
OPERATOR'S MANUAL
MANUEL D'UTILISATION
BEDIENUNGSANLEITUNG
MANUALE PER L'OPERATORE
MANUAL DE INSTRUCCIONES
AH236S-LW
ENGLISH
FRANÇAIS
DEUTSCH
ITALIANO
ESPAÑOL
WARNING
READ THE INSTRUCTIONS CAREFULLY AND FOLLOW THE RULES FOR
SAFE OPERATION.
FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY.
AVERTISSEMENT
LIRE ATTENTIVEMENT LES INSTRUCTIONS ET SUIVRE LES RÈGLES DE
SECURITÉ.LE NON-RESPECT DES RÈGLES DE SÉCURITÉ ENTRAÎNE UN
RISQUE DE BLESSURE GRAVE.
WARNUNG
LESEN SIE DIE BEDIENUNGSANLEITUNG SORGFÄLTIG DURCH, UND
BEFOLGEN SIE DIE SICHERHEITSREGELN. ANDERNFALLS BESTEHT DAS
RISIKO SCHWERER VERLETZUNGEN.
AVVERTENZA
LEGGERE E SEGUIRE ATTENTAMENTE LE ISTRUZIONI PER LAVORARE IN
CONDIZIONI DI MASSIMA SICUREZZA. LA MANCATA OSSERVANZA DELLE
ISTRUZIONI POTREBBE PROVOCARE LESIONI GRAVI.
ADVERTENCIA
LEA ATENTAMENTE LAS INSTRUCCIONES Y SIGA LAS INDICACIONES
PARA UN FUNCIONAMIENTO SEGURO. DE NO HACERLO, PODRÍA SUFRIR
LESIONES GRAVES.
??
1Top cover
ENGLISH
(Original instructions)
OPERATOR'S MANUAL
ARTICULATED HEDGE TRIMMER
AH236S-LW
WARNING
READ THE INSTRUCTIONS CAREFULLY AND FOLLOW THE
RULES FOR SAFE OPERATION.
FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY.
2
Important information
2Important information
Please ensure that you read the operator's manual before using your product.
Intended use of this product
shindaiwa Hedge Trimmer are lightweight, high-performance, petrol engined units designed for hedge and shrub trim-
ming.
Do not use this unit for any purpose other than aforementioned.
Users of the product
You should not use this product until you have read the operator's manual carefully and fully absorbed its content.
This product should not be used by anyone who has failed to read the operator's manual properly, is suffering from a
cold, tiredness or otherwise in poor physical condition, or children.
Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their prop-
erty.
About your operator's manual
This manual contains necessary information about the operation and maintenance of your product. Please read it care-
fully and absorb its contents.
Always keep your manual in a place where it is readily accessible.
If you have lost your manual or it is damaged and no longer readable, please purchase a new one from your shindaiwa
dealer.
The units used in this manual are SI units (International System of Units). Figures in parentheses are reference values,
and there may be a slight conversion error in some cases.
Loaning or assigning your product
When loaning the product described in this manual to another party, ensure that the person borrowing and working with
the product receives the operator's manual along with the product. If you assign your product to another party, please
enclose the operator's manual with the product when handing it over.
Enquiries
Please contact your shindaiwa dealer for requests regarding information about your product, the purchase of consum-
ables, repairs, and other such enquiries.
Notices
The content of this manual may be changed without notice for the purpose of upgrades to the product. Some of the
illustrations used may differ from the product itself in order to make the explanations clearer.
This product requires the assembly of some parts.
Please consult your shindaiwa dealer if anything is unclear or of concern.
Feature of this model: Soft Start
Soft Start generates enough revolving power to rotate crankshaft up to a speed to ignite the engine and bring almost
no kickback. Soft Start makes engine start far easier than you ever expect.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a re-
placement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are
also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not
amount to a major failure.
For warranty service, find the nearest Authorised Service Dealer in our dealer locator map at www.echo australia.com.au/
en_au/finder, or by calling 1300 274 447, or by emailing or writing to salesenquires@briggsandstratton.com.au, Briggs &
Stratton Australia Pty Ltd, Locked bag 5004, St Clair, NSW 2759.
3
Contents
For safe use of your product............................................................................................... 4
Warning notices............................................................................................................. 4
Other indicators ............................................................................................................. 4
Symbols.........................................................................................................................4
Location in which the safety decal is attached............................................................... 6
Handling fuel.................................................................................................................. 7
Handling the engine....................................................................................................... 7
Handling the product ..................................................................................................... 9
Packing list........................................................................................................................ 13
Description........................................................................................................................ 14
Before you start ................................................................................................................15
Assembly ..................................................................................................................... 15
Adjusting Cutting Angle ............................................................................................... 17
Shoulder strap ............................................................................................................. 18
Preparing the fuel ........................................................................................................ 19
Engine operation............................................................................................................... 20
Starting the engine ...................................................................................................... 20
Stopping the engine..................................................................................................... 21
Hedge and shrub trimming operation ............................................................................... 22
Basic hedge trimming operation .................................................................................. 22
Maintenance and care ...................................................................................................... 23
Maintenance and care ................................................................................................. 23
Storage ............................................................................................................................. 29
Long-term storage (30 days or more).......................................................................... 29
Disposal procedure........................................................................................................... 30
Specifications.................................................................................................................... 31
Declaration of conformity .................................................................................................. 32
4
For safe use of your product
For safe use of you r product
Be careful to read this section before using your product.
The precautions described in this section contain important safety information. Please observe them carefully.
You must also read the precautions that appear in the body of the manual itself.
Text following a [diamond mark] mark describes the potential consequences of failing to observe the precaution.
Warning notices
Situations where there is a risk of physical injury to the operator and other people are indicated in this manual and on the product
itself by the following warning notices. Always read and observe them carefully in order to ensure safe operation.
Other indicators
As well as warning notices, this manual uses the following explanatory symbols:
Symbols
In this manual and on the product itself, a series of explanatory symbols is used. Please make sure that you fully understand what
each symbol means.
DANGER WARNING CAUTION
This symbol accompanied by the
word "DANGER" calls attentions to
an act or a condition which will lead to
serious personal injury or death of op-
erators and bystanders.
This symbol accompanied by the
word "WARNING" calls attentions to
an act or a condition which can lead to
serious personal injury or death of op-
erators and bystanders.
"CAUTION" indicates a potentially
hazardous situation which, if not
avoided, may result in minor or mod-
erate injury.
Circle and slash sym-
bol means whatever is
shown is prohibited.
NOTE IMPORTANT
This enclosed message provides tips
for use, care and maintenance of the
product.
Framed text featuring the word "IM-
PORTANT" contains important infor-
mation about the use, checking,
maintenance and storage of the prod-
uct described in this manual.
Symbol form/shape Symbol description/applica-
tion
Symbol form/shape Symbol description/applica-
tion
Carefully read the operator's
manual Petrol and oil mixture
Wear eyes, ears and head
protection Purge bulb (Primer)
Safety / Alert Finger severing
Emergency stop Carburettor adjustment
- Idle speed
Do not use the product in plac-
es with poor ventilation
Choke Control
"Cold Start"
Position
(Choke Closed)
5
For safe use of your product
Beware of fire
Choke Control
"Run"
Position
(Choke Open)
Beware of electric shocks Environmental protection!
Beware of high-temperature
areas
Guaranteed sound power lev-
el
Engine start
This product conducts elec-
tricity. Keep the product and/
or operator a minimum dis-
tance of 10 meters away from
electrical source and power
lines.
Wear heavy duty, non-slip
gloves.
Safety tip shoes or boots with
non-slip sole should be worn.
Keep bystanders at least 15
meters away from the operat-
ing trimmer to reduce the risk
of being struck by falling ob-
jects or thrown debris.
Be aware of the danger of fall-
ing debris.
Symbol form/shape Symbol description/applica-
tion
Symbol form/shape Symbol description/applica-
tion
6
For safe use of your product
Location in which the safety decal is attached
The safety decal shown below has been attached to the products described in this manual. Ensure that you understand what
the decal means before using your product.
If the decal becomes unreadable due to wear and tear or damage, or peels off and is lost, please purchase a replacement decal
from your dealer and attach it in the location shown in the illustrations below. Ensure that the decal is readable at all times.
1. Safety decal (Part number X505-002890)
7
For safe use of your product
Handling fuel
Handling the engine
DANGER
Always keep well away from fire when refuelling
Fuel is highly inflammable and leads to a risk of fire if mishandled. Use extreme care when mixing, storing or handling
or serious personal injury may result. Be careful to observe the following instructions.
Do not smoke or hold a flame near when refuelling.
Do not fuel up while the engine is hot or in operation.
If you do so, the fuel could ignite and cause fire, leading to burns.
About the container and refuelling place
Use an approved fuel container.
Fuel tanks/cans may be under pressure.
Always loosen fuel caps slowly allowing pressure to
equalize.
DO NOT fill fuel tanks indoors.
ALWAYS fill fuel tanks outdoors over bare ground.
Fuel spills can cause fire
Observe the following precautions when refuelling:
Do not add so much fuel that it reaches the mouth of the
fuel tank. Keep the fuel within the prescribed level (up to
the shoulder level of the fuel tank).
Mop up any fuel that overflows or spills out due to over-
filling.
Tighten the fuel tank cap securely after refuelling.
Fuel spills can cause fire and burns when ignited.
1. Fuel tank
2. Shoulder level
Do not start the engine in the area where you refue-
led
You must not start the engine in the place where you
carried out the refuelling. Move at least 3m from the
place where you refueled before starting the engine.
Fuel leaks that occur while refuel-
ling can cause fire if ignited.
Fuel leaks cause fire
After refuelling, always check
that there are no leaks or dis-
charges of fuel from the fuel
pipe, fuel system grommets, or
around the fuel tank cap.
If you do find fuel leaks or discharges, stop using the
product immediately and contact your dealer to have it
repaired.
Any fuel leaks could cause fire.
DANGER
Keep the trimmer at least 10 meters away from electrical lines or branches that contact electrical lines
The articulated hedge trimmer is not insulated against electrical shock. Keep the trimmer at least 10 meters away from
electrical lines or branches that contact electrical lines.
Approaching or contacting electrical lines with the trimmer could cause death or serious injury.
8
For safe use of your product
WARNING
Starting the engine
Be particularly careful to observe the following precau-
tions when starting the engine:
Always ensure all handles and guards are fitted
Check that none of the nuts and bolts are loose
Check that there are no fuel leaks
Check that the cutter blades is not damaged or exces-
sively worn. If you find any abnormalities, do not use
the product.
Place the product in a flat, well ventilated place
Leave plenty of space around the product and do not al-
low people or animals near it
Remove obstructions, if any
Make sure that the cutter blades is not touching the
ground or any obstacles
Start the engine with the throttle trigger in the idle speed
position
Hold the product firmly to the ground when starting the
engine
Do not start the engine holding the product in the air
Failure to observe the precautions could cause an accident
or injury, or even lead to a fatality.
Once the engine has started, check for abnormal vi-
brations and sounds
Check that there are no abnormal vibrations or sounds
once the engine starts. Do not use the product if there
are abnormal vibrations or sounds. Contact your dealer
to have it repaired.
Accidents involving parts that fall or shatter off can cause
wounds or serious injury.
Do not touch high temperature or high voltage com-
ponents while the product is running
Do not touch the following high temperature or high volt-
age components while the product is running or for some
time after it stops.
Silencer, spark plug, gear housing, and
other high temperature components
You could burn yourself if you touch a high
temperature component.
Spark plug, spark plug wire, and other
high voltage components
You could receive an electric shock if you
touch a high voltage component while the
product is running.
Put safety first in the case of fire or smoke
If fire comes from the engine or smoke appears from
any area other than the exhaust vent, first distance
yourself from the product to ensure your physical safe-
ty.
Use a shovel to throw sand or other such
material on the fire to prevent it from
spreading, or put it out with a fire extin-
guisher.
A panicked reaction could result in the fire and
other damage becoming more extensive.
Exhaust fumes are toxic
The exhaust fumes from the engine contain toxic gases.
Do not operate the product indoors or in a plastic green-
house or in other ill ventilated places.
The exhaust fumes could cause poisoning.
Turn off the engine when checking or maintaining
the product
Observe the following precautions when checking and
maintaining your product after use:
Turn the engine off and do not attempt to check or main-
tain the product until the engine has cooled
You could burn yourself.
Remove the spark plug cap before performing checks
and maintenance
An accident could occur if the product starts unexpectedly.
Checking the spark plug
Observe the following precautions when checking the
spark plug.
If the electrodes or terminals are worn, or if there are
cracks in the ceramics, replace them with new parts.
The spark test (for checking whether the spark plug is
sparking) must be carried out by your dealer.
The spark test must not be carried out in proximity of
the spark plug hole.
The spark test must not be performed in places where
there are fuel spills or inflammable gases
You must not touch the
metal parts of the spark
plug
The spark plug could ig-
nite a fire or give you an
electric shock.
9
For safe use of your product
Handling the product
General precautions
Precautions for use
WARNING
Operator's manual
Be careful to read the operator's manual
properly before using your product in or-
der to ensure correct operation.
Failure to do so could lead to an accident or
serious injury.
Do not use the product for anything
other than its intended purpose
You must not use the product for any purpose other
than those described in the operator's manual.
To do so could lead to an accident or serious injury.
Do not modify the product
You must not modify the product.
To do so could lead to an accident or serious injury. Any
malfunction resulting from a modification to the product will
not be covered by the manufacturer's warranty.
Do not use the product unless it has been checked
and maintained
You must not use the product unless it has been
checked and maintained. Always ensure that the prod-
uct is checked and maintained on a regular basis.
Failure to do so could lead to an accident or serious injury.
Loaning or assigning your product
When loaning your product to another party, ensure
that the person borrowing the product receives the op-
erator's manual along with it.
If you assign your product to another party, please en-
close the operator's manual with the product when
handing it over.
Failure to do so could lead to an accident or serious injury.
Being prepared in case of an injury
In the unlikely event of an accident or injury, please ensure
that you are prepared.
First aid kit
Towels and wipes (to stop any bleeding)
Whistle or mobile phone (for calling outside help)
If you are unable to perform first aid or call for outside help,
the injury could worsen.
DANGER
Always stop the engine when a blades jam occurs
Do not attempt to remove an object causing a blades jam if the engine is running.
Physical injury can occur if a blades jam is removed and the blades starts moving.
10
For safe use of your product
WARNING
Users of the product
The product should not be used by:
people who are tired
people who have taken alcohol
people who are on medication
people who are pregnant
people who are in poor physical
condition
people who have not read the op-
erator's manual
children
Failure to observe these instruc-
tions could lead to an accident.
The ignition system of this product generates electro-
magnetic fields during operation. Magnetic fields can
cause pacemaker interference or pacemaker failure. To
reduce health risks, we recommend that pacemaker us-
ers consult their physician and the pacemaker manu-
facturer before operating this product.
Environment of use and operation
Do not use the product in places where there is no sure
foothold, such as on steep slopes or after rainfall, as
such places are slippery and dangerous.
Maintain footing and balance at all times. Do not stand
on slippery, uneven or unstable surfaces. Do not work
in odd positions or on ladders. Do not over reach.
Do not operate the product at night or in dark places
with poor visibility.
Heavy protective clothing can increase operator fatigue
which may lead to heat stroke. Schedule heavy work for
early morning or late afternoon hours when tempera-
tures are cooler.
When cutting a branch that is under tension, be alert for
spring-back so that you will not be struck by the moving
branch.
A serious injury could result if you fall or slip, or fail to oper-
ate the product correctly.
Transport of the product
When transporting in the situations described below, turn
off the engine and ensure that the cutter blades has
stopped moving, then fit the blade cover and position the
silencer away from yourself.
Moving to the place where you are working
Moving to another area while you are working
Leaving the place where you have been working
Failure to observe these precautions could cause burns or
serious injury.
When transporting the product by car, empty the fuel
tank, fit the blade cover, and secure the product firmly
in place to prevent it from moving around.
When carrying the articulated hedge trimmer by hand,
the cutter attachment should be pointing backward with
the cutter blade in the retracted or transporting posi-
tion.
Travelling by car with fuel in the fuel tank could lead to a fire.
Vibration and cold
It is believed that a condition called Raynaud's Phenome-
non which affects the fingers of certain individuals may be
brought about by exposure to vibration and cold. Expo-
sure to vibration and cold may cause tingling and burning,
followed by loss of colour and numbness in the fingers.
The following precautions are strongly recommended be-
cause the minimum exposure which might trigger the ail-
ment is unknown.
Keep your body warm, especially the head and neck,
feet and ankles, and hands and wrists.
Maintain good blood circulation by performing vigorous
arm exercises during frequent work breaks, and also by
not smoking.
Limit the number of hours of operation.
Try to fill each day with jobs where operating the hedge
trimmer or other hand-held power equipment is not re-
quired.
If you experience discomfort redness and swelling of
the fingers, followed by whitening and loss of feeling,
consult your physician before exposing yourself further
to cold and vibration.
Failure to observe these instructions could result in damage
to your health.
Repetitive stress injuries
It is believed that over-using the muscles and tendons of
the fingers, hands, arms and shoulders may cause sore-
ness, swelling, numbness, weakness and extreme pain to
the areas just mentioned. Certain repetitive hand activities
may put you at a high risk for developing a repetitive
stress injury (RSI).
To reduce the risk of RSI, do the following:
Avoid using your wrist in a bent, extended or twisted
position.
Take periodic breaks to minimize repetition and rest
your hands. Reduce the speed and force in which you
do the repetitive movement.
Do exercises to strengthen hand and arm muscles.
See a doctor if you feel tingling, numbness or pain in
your fingers, hands, wrists or arms. The sooner RSI is
diagnosed, the more likely permanent nerve and muscle
damage can be prevented.
Failure to observe these instructions could result in damage
to your health.
11
For safe use of your product
WARNING
Remove foreign objects and obstructions before
working with the product
Inspect area that the product will be used in. Remove
stones, metal objects and any other object that could
jam or damage the product.
An accident or serious injury can occur if foreign objects
throw the cutting device.
Turn off the engine immediately if anything goes
wrong
In the following situations, turn off the engine immediately
and ensure that the cutting device has stopped before
checking each area of the product. Replace any damaged
parts.
If the cutting device hits a rock, tree, post, or other such
obstruction while you work.
If the product suddenly starts to vibrate abnormally.
Continuing to use parts when they are damaged could lead
to an accident or serious injury.
The area within a 15 m radius is a danger zone
The area within a 15 m radius of the product is a danger
zone. Be careful to observe the following precautions
while working with the product.
Do not allow children and other people or pets to enter
the danger zone.
If another person enters the danger zone, turn off the
engine to stop the blades.
When approaching the operator, signal to him by, for
example, throwing twigs from outside the danger zone,
and then check that engine has been switched off and
the blades has stopped moving.
Do not allow anyone to hold the material you are cut-
ting.
Any contact with the cutter blades could cause serious inju-
ry.
Do not use the product when the cutter blades is
moving at idle speed
You must not use the product while the cutter blades is
moving if the Hedge Trimmer is running with the throttle
trigger in the idle speed position. Turn off the engine im-
mediately and adjust the carburettor.
To do so could lead to an accident or serious injury.
Operation
Never remove hands from the product when the blades
are moving.
Only adjust cutting angle with unit resting flat on the
ground, with the switch in the "STOP" position. Never
adjust blade angle while standing.
Failure to observe these instructions will cause the product
to be held unsteadily and could result in serious injury.
Make sure that the cutter blades is stopped before
putting the product on the ground
When you turn off the engine, check to ensure the cutter
blades has stopped moving before you lower the prod-
uct to the ground.
Even if the engine has been turned off, the blades can still
cause an injury while free-wheeling.
Remove debris from the silencer
If objects such as grasses, leaves, twigs or excessive
grease got stuck over the area around the silencer of
the engine, stop the engine and remove them paying at-
tention not to touch hot spots.
Failure to do so could lead to a fire.
WARNING
Do not use the product to cut hard objects
Do not use the product to cut hard objects such as
wires or steel plates.
If the blades strikes an obstruction or is prevented from
functioning properly, stop the engine and inspect the
blades for damage.
Failure to follow these instructions could cause breakage of
the product or an accident.
Never use the product getting on a ladder or a stool
Do not overreach or stand on unstable surfaces.
Do not use the product when being at the top of the lad-
der or standing on a stool.
Failure to do so could lead to an accident or serious injury.
12
For safe use of your product
Protective gear
WARNING
Wear protective gear
Always wear the following protective gear when working
with the hedge trimmer.
a Head protection (helmet): Protects the head
b Ear muffs or ear plugs: Protect the hearing
c Safety goggles: Protect the eyes
d Safety gloves: Protect the hands from cold and vibration
e Work clothes that fit (long sleeves, long trousers): Pro-
tect the body
f Heavy duty, non-slip protective boots or non-slip work
shoes : Protect the feet
Failure to observe these precautions could result in damage
to your sight or hearing, or lead to a serious injury.
When necessary, please use the protective gear below.
Dust mask: Protects the breathing apparatus
Bee net: To deal with attacks by bees
Full face shield: When trimming overhead, wear head pro-
tection meeting CE with a full face shield.
Wear proper clothing
Do not wear ties, jewellery, or loose, dangling clothing which could be
caught in the unit. Do not wear open toed footwear, or go bare-foot or
barelegged.
Failure to observe these precautions could result in damage to your sight or
hearing, or lead to a serious injury.
13
Packing list
Packing list
The following parts are packed separately in the packing box.
When you have unpacked the box, please check the parts that it contains.
Contact your dealer if anything is missing or broken.
1. Power head
2. Operation shaft
3. Blade cover
4. Shoulder strap
5. L-wrench
6. Spanner
7. Socket wrench
8. Operator's manual
14
Description
Descript ion
1. Ignition switch Device for allowing the engine to be
started and stopped.
2. Throttle trigger lockout Device that prevents the acci-
dental operation of the throttle trigger until manually re-
leased.
3. Spark plug
4. Air cleaner cover Covers air filter.
5. Fuel tank cap For closing the fuel tank.
6. Fuel tank Contains fuel and fuel filter.
7. Throttle trigger Device activated by the operator's fin-
ger, for controlling the engine speed.
8. Front grip
9. Hand guard Guard between the front handle and cut-
ting device for protecting the hand from injuries if the
hand slips off the handle.
10. Outer tube Part of the unit that provides a casing for
power transmission shaft.
11. Cutter assembly adjustment lever Provides secure
hand grip for adjusting cutting blade angle.
12. Hedge trimmer cutter assembly
13. Latch lock Fixes the angle of the cutter.
14. Latch release Safety device to prevent the latch lock
from being released unexpectedly.
15. Knob Releases the rotation regulation when it is pulled.
16. Gear housing assembly Gear housing contains drive
gears for transmitting power to cutting blades.
17. Cutter bar and cutter blades That part of the assembly
of cutter blade and shear plate together with any sup-
porting part, which performs the cutting action.
18. Blunt extension An extending blunt part of the cutting
device.
19. Blade cover When transporting or storing the product
always fit the blade cover.
20. Suspension point Device on which the strap can be
hooked.
21. Shoulder strap An adjustable strap to suspend unit.
22. Starter handle Pull handle to start the engine.
23. Type and serial number
15
Before you start
Before you start
Assembly
Connect the outer tube to the powerhead
1. Place the powerhead on a clean, flat surface, spark plug fac-
ing up.
2. Slip off the protective cover from the end of the outer tube.
3. Use the L-wrench to loosen the tube clamp screw.
4. Slide the outer tube into the tube clamp until the tube bot-
toms. If installation is difficult, rotate the outer tube or main
shaft slightly until you feel the drive shaft splines engage with
the powerhead.
5. Position the outer tube so that the gearcase output shaft is
facing left on silencer cover.
6. Slide the outer tube into the powerhead until the throttle grip
just contacts the tube clamp.
7. Tighten the clamp screw firmly.
Connect the throttle cable
1. Loosen the air cleaner cover knob and remove the air clean-
er cover.
WARNING
Read the operator's manual carefully to ensure that you assemble the product correctly.
Using a product that has been incorrectly assembled could lead to an accident or serious injury.
1. Spark plug
2. Clamp screw
3. Tube clamp
4. Drive shaft
5. Outer tube
6. Protective cover
WARNING
Ensure that the fuel tank cap is securely in place.
Failure to do so could lead to an injury or serious accident,
or cause a fire.
1. L-wrench
2. Tube clamp
CAUTION
Do not force the shaft tube into the powerhead.
Excessive force can damage the shaft tube and drive shaft.
1. Air cleaner cover
2. Air cleaner cover knob
16
Before you start
2. Place throttle cable into adjustment fixture and install wire
end into large carburettor throttle swivel hole.
3. The throttle lever free play should be approximately 4-6 mm.
4. Turn the adjustment nut in or out as required to obtain proper
free play 4-6 mm.
5. Make sure that the throttle lever operates smoothly without
binding.
6. Check throttle for freedom of movement and that wide open
throttle / low idle extremes are adjusted properly.
7. Tighten locknut.
8. Connect 2 ignition leads from throttle cable tubing to 2 igni-
tion leads on engine.
9. Secure ignition leads against engine with clips.
10. Install air cleaner cover.
1. Throttle cable
2. Adjustment fixture
3. Throttle swivel hole
4. Adjustment nut
5. Locknut
1. Ignition leads
1. Ignition leads
2. Clip
3. Clip
CAUTION
Wiring runs must not interfere with throttle operation.
17
Before you start
Adjusting Cutting Angle
Adjusting the hedge trimmer cutter assembly
1. Position the hedge trimmer on a flat, level surface with the
engine resting on the fuel tank guard. Make sure the blade
cover is in place on the blade.
2. Pull the tip of hand guard, and remove the cutter assembly.
3. With your right hand, grasp the outer tube near the handle.
With your left hand, grip the adjustment lever on the cutter
assembly. With the index finger of your left hand, press the
latch release. With your left thumb, press the latch lock.
4. While holding the latch release down, pivot the cutter assem-
bly using the adjustment lever until it is at the desired cutting
angle.
5. Release the latch lock and the latch release. Make sure the
latch lock and the latch release return securely to the straight
ahead position.
6. Remove the blade cover from the cutter blade. The engine
now may be started.
DANGER
Never adjust cutting assembly with engine running.
Failure to do so could lead to an injury or serious accident.
WARNING
Hedge trimmer blades are sharp. Always wear gloves when adjusting cutting assembly.
Wear heavy duty gloves when working with the hedge trimmer blades. When replacing the hedge trimmer blades
during a trimming task, ensure that the engine is switched off and that the blades have stopped.
Do not stand hedge trimmer on end when adjusting cutting angle, otherwise serious injury may result.
Gear case assembly becomes HOT during use. Always grip assembly at blade-adjustment handle when making cut-
ting angle adjustments, otherwise serious injury may result.
Failure to do so could lead to an injury or serious accident.
1. Cutter assembly
2. Hand guard
1. Adjustment lever
2. Latch release
1. Latch lock
1. Adjustment lever
IMPORTANT
The latch release provides an interlock to help prevent inad-
vertent depression of the latch lock.
18
Before you start
Cutter assembly position
The cutter assembly can be adjusted to ten different positions
ranging from 135° to 270° from the outer tube as shown. Al-
ways make sure the lock latch is securely locked after each
adjustment.
Adjusting for Storage or Transportation
1. With the engine off, install the blade cover onto the blade.
2. Rotate the cutter assembly so it is parallel to the tube. The
rotation is restricted at the position of 135° by the lock pin.
Pull the knob and release the lock pin.
3. Make sure the latch lock and the latch release return secure-
ly to a locking position.
4. Fit the tip of the cutter assembly into the storage position of
the hand guard and fix it.
5. Make sure the blade cover is in place on the cutters before
storing or transporting.
Shoulder strap
1. Hook the strap hook to the hanger on the outer tube.
2. Wear the shoulder strap so that the hook stays at your right
hand side.
3. Adjust the length of the shoulder strap so that you can hold
and operate the machine comfortably.
Emergency Release
In case of emergency, strongly pull the white tab at the hook.
The machine will be released from the strap.
1. Knob
1. Support notch
2. Blade cover
WARNING
Never run the engine when adjusting the cutter assem-
bly to the storage position.
IMPORTANT
Adjust the shoulder strap or harness so the shoulder pad rests
comfortably on the off-side shoulder. Make sure all hooks and
adjustment devices are secure.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176

Shindaiwa AH236S-LW Manuale utente

Categoria
Tagliasiepi a motore
Tipo
Manuale utente