Siemens ET875LMV1D/06 Manuale utente
- Categoria
- Piani cottura
- Tipo
- Manuale utente
Questo manuale è adatto anche per
ET8..LMV1.
Hob
[en] Instruction manual
2 Ø = cm
(7
/09
[
[
en
3
Table of contents
enI nst r uct i on manual
8 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
( Important safety information . . . . . . . . . . . . . . . 4
] Causes of damage . . . . . . . . . . . . . . . . . . . . . . . . 5
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
7 Environmental protection . . . . . . . . . . . . . . . . . . 5
Energy-saving tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Environmentally-friendly disposal . . . . . . . . . . . . . . . . . 5
* Getting to know your appliance . . . . . . . . . . . . . 6
The control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
The hotplates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Residual heat indicator. . . . . . . . . . . . . . . . . . . . . . . . . 7
1 Operating the appliance . . . . . . . . . . . . . . . . . . . 7
Switching the hob on and off . . . . . . . . . . . . . . . . . . . . 7
Setting a hotplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Table of cooking times. . . . . . . . . . . . . . . . . . . . . . . . . 8
c Frying Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Pans for the sensor frying system . . . . . . . . . . . . . . . . 9
The frying settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Setting the sensor frying system . . . . . . . . . . . . . . . . . 9
Switching off the sensor frying system . . . . . . . . . . . . . 9
Frying table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
v PowerBoost function . . . . . . . . . . . . . . . . . . . . . 10
Switching on PowerBoost. . . . . . . . . . . . . . . . . . . . . . 10
Switch off PowerBoost . . . . . . . . . . . . . . . . . . . . . . . . 11
A Childproof lock. . . . . . . . . . . . . . . . . . . . . . . . . . 11
Switching the childproof lock on and off . . . . . . . . . . 11
Automatic childproof lock . . . . . . . . . . . . . . . . . . . . . 11
O Time-setting options . . . . . . . . . . . . . . . . . . . . . 11
Automatic hotplate switch-off . . . . . . . . . . . . . . . . . . . 11
Automatic timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Kitchen timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Stopwatch function. . . . . . . . . . . . . . . . . . . . . . . . . . . 12
b Automatic safety cut-out . . . . . . . . . . . . . . . . . . 12
z Keep warm function. . . . . . . . . . . . . . . . . . . . . . 12
Switching on the Keep warm function . . . . . . . . . . . . 12
Switching off the Keep warm function . . . . . . . . . . . . 12
k Wipe protection . . . . . . . . . . . . . . . . . . . . . . . . . 12
[ Energy consumption indicator . . . . . . . . . . . . . 13
Q Basic settings. . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Changing the basic settings. . . . . . . . . . . . . . . . . . . . 13
o Home Connect . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Setting up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Home Connect settings . . . . . . . . . . . . . . . . . . . . . . .15
Software update . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
About data protection . . . . . . . . . . . . . . . . . . . . . . . . .17
Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . .17
e Hood connection . . . . . . . . . . . . . . . . . . . . . . . . 18
Setting up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Resetting connection . . . . . . . . . . . . . . . . . . . . . . . . .19
Control the hood via the hob . . . . . . . . . . . . . . . . . . .19
Hood control settings . . . . . . . . . . . . . . . . . . . . . . . . .19
D Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Ceramic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Hob surround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
3 Trouble shooting . . . . . . . . . . . . . . . . . . . . . . . . 20
E-report in the displays . . . . . . . . . . . . . . . . . . . . . . . .21
4 Customer service . . . . . . . . . . . . . . . . . . . . . . . . 21
E number and FD number . . . . . . . . . . . . . . . . . . . . .21
E Test dishes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Produktinfo
Additional information on products, accessories,
replacement parts and services can be found at
www.siemens-home.bsh-group.com and in the online
shop www.siemens-home.bsh-group.com/eshops
en Intended use
4
8Intended use
Intended use
Read these instructions carefully. Please keep
the instruction and installation manual, as well
as the appliance certificate, in a safe place for
later use or for subsequent owners.
Check the appliance for damage after
unpacking it. Do not connect the appliance if it
has been damaged in transport.
Only a licensed professional may connect
appliances without plugs. Damage caused by
incorrect connection is not covered under
warranty.
This appliance is intended for private domestic
use and the household environment only. The
appliance must only be used for the
preparation of food and beverages. The
cooking process must be supervised. A short
cooking process must be supervised without
interruption. Only use the appliance in
enclosed spaces.
This appliance is intended for use up to a
maximum height of 2000 metres above sea
level.
This appliance may be used by children over
the age of 8 years old and by persons with
reduced physical, sensory or mental
capabilities or by persons with a lack of
experience or knowledge if they are
supervised or are instructed by a person
responsible for their safety how to use the
appliance safely and have understood the
associated hazards.
Children must not play with, on, or around the
appliance. Children must not clean the
appliance or carry out general maintenance
unless they are at least 15 years old and are
being supervised.
Keep children below the age of 8 years old at
a safe distance from the appliance and power
cable.
(Important safety
information
Impor t ant saf et y informat i on
:Warning – Risk of fire!
■ Hot oil and fat can ignite very quickly. Never
leave hot fat or oil unattended. Never use
water to put out burning oil or fat. Switch off
the hotplate. Extinguish flames carefully
using a lid, fire blanket or something similar.
Risk of fire!
■ The hotplates become very hot. Never
place combustible items on the hob. Never
place objects on the hob.
Risk of fire!
■ The appliance gets hot. Do not keep
combustible objects or aerosol cans in
drawers directly underneath the hob.
Risk of fire!
■ The hob switches off automatically and can
no longer be operated. It may switch on
unintentionally at a later point. Switch off the
circuit breaker in the fuse box. Contact the
after-sales service.
Risk of burns!
■ Do not use hob covers here.They can
cause accidents, for example due to
overheating, catching fire or materials
shattering.
:Warning – Risk of burns!
■ The hotplates and surrounding area
(particularly the hob surround, if fitted)
become very hot. Never touch the hot
surfaces. Keep children at a safe distance.
Risk of burns!
■ The hotplate heats up but the display does
not work. Switch off the circuit breaker in
the fuse box. Contact the after-sales
service.
Risk of burns!
■ It is only allowed to use safety devices, e.g.
hob guards, which have been approved by
ourselves. Unsuitable safety devices or hob
guards may result in accidents.
:Warning – Risk of electric shock!
■ Incorrect repairs are dangerous. Repairs
may only be carried out and damaged
power cables replaced by one of our
trained after-sales technicians. If the
appliance is defective, unplug the appliance
from the mains or switch off the circuit
breaker in the fuse box. Contact the after-
sales service.
Risk of electric shock!
■ Do not use any high-pressure cleaners or
steam cleaners, which can result in an
electric shock.
Risk of electric shock!
■ A defective appliance may cause electric
shock. Never switch on a defective
appliance. Unplug the appliance from the
mains or switch off the circuit breaker in the
fuse box. Contact the after-sales service.
Risk of electric shock!
■ Cracks or fractures in the glass ceramic
may cause electric shocks. Switch off the
circuit breaker in the fuse box. Contact the
after-sales service.
Causes of damage en
5
:Warning – Risk of injury!
Saucepans may suddenly jump due to liquid
between the pan base and the hotplate.
Always keep the hotplate and saucepan bases
dry.
]Causes of damage
Causes of damage
Caution!
■ Rough pot and pan bases scratch the ceramic.
■ Avoid boiling pots dry. This may cause damage.
■ Never place hot pots or pans on the control panel,
the display area or the surround. This may cause
damage.
■ Damage can occur if hard or pointed objects fall on
the hob.
■ Aluminium foil and plastic containers melt on hot
hotplates. Oven protective foil is not suitable for your
hob.
Overview
You will find the most frequently caused damage in the
following table.
7Environmental protection
En v i r o n ment al pr ot ec t i on
In this section, you can find information about saving
energy and disposing of the appliance.
Energy-saving tips
■ Always place suitable lids on saucepans. When
cooking without a lid, considerably more energy is
required. A glass lid means that you can see inside
without having to lift the lid.
■ Use pots and pans with even bases. Uneven bases
increase energy consumption.
■ The diameter of pot and pan bases should be the
same size as the hotplate. In particular, small
saucepans on the hotplate cause energy losses.
Please note: cookware manufacturers often indicate
the upper diameter of the saucepan. This is usually
bigger than the diameter of the base of the pan.
■ Use a small saucepan for small quantities. A larger,
less full saucepan requires a lot of energy.
■ Cook with only a little water. This will save energy.
Vitamins and minerals in vegetables are preserved.
■ Always cover as large an area of the hotplate as
possible with your saucepan.
■ Switch to a lower heat setting in good time.
■ Select a suitable ongoing cooking setting. You will
waste energy by using an ongoing cooking setting
which is too high.
■ Use the residual heat of the hob. For longer cooking
times, you can switch the hotplate off 5-10 minutes
before the end of the cooking time.
Environmentally-friendly disposal
Dispose of packaging in an environmentally-friendly
manner.
Damage Cause Measure
Stains Boiled over food Remove boiled over food imme-
diately with a glass scraper.
Unsuitable clean-
ing agents
Only use cleaning agents that
are suitable for glass ceramic.
Scratches Salt, sugar and
sand
Do not use the hob as a work
surface or storage space.
Rough pot and
pan bases
scratch the
ceramic.
Check your cookware.
Discolouration Unsuitable clean-
ing agents
Only use cleaning agents that
are suitable for glass ceramic.
Pan abrasion (e.g.
aluminium)
Lift pots and pans when moving
them.
Blisters Sugar, food with a
high sugar con-
tent
Remove boiled over food imme-
diately with a glass scraper.
This appliance is labelled in accordance with
European Directive 2012/19/EU concerning
used electrical and electronic appliances
(waste electrical and electronic equipment -
WEEE). The guideline determines the
framework for the return and recycling of used
appliances as applicable throughout the EU.
en Getting to know your appliance
6
*Getting to know your
appliance
Get t i ng to know your appl i ance
The instruction manual is the same for various different
hobs. You can find the hob dimensions in the overview
of models. ~ Page 2
The control panel
Notes
■ Depending on the operating condition of the hob the
controls which can currently be selected light up
brightly or dimmed. If you touch them, the relevant
function is activated.
■ The controls which cannot currently be selected do
not light up.
■ The settings of the hotplates currently selected light
up brightly.
■ Always keep the controls dry. Moisture reduces their
effectiveness.
■ Do not pull pans close to the displays and sensors.
The electronics could overheat.
The hotplates
Notes
■ Any dark areas in the glow pattern of the hotplate
are due to technical reasons. The function of the
hotplate is not affected.
■ Hotplate temperature is regulated by the heat
switching on and off.The heat may also switch on
and off at the highest setting.
This ensures e.g.:
– sensitive components are protected from
overheating
– the appliance is protected from electrical
overload
– better cooking results are achieved
Í
E
E
ÍÍ
q
Î
Indica-
tors/sym-
bols
‚-Š
Heat settings
•/œ
Residual heat
›
PowerBoost function
–
Keep-warm function
‰‰
Timer
D
Wi-Fi
Controls
#
Main switch
b PowerBoost function
¢
Hotplate selection
$
Child safety lock
Wipe protection
a
Fan setting hood
Õ
Sensor frying system
0IIIIIIIIIIIII Control panel*
ð
Activating the dual-circuit hotplate
ˆ
Activating the small cooking zone
Ô
Activating the extended cooking zone
=
Lighting hood
è
Keep-warm function
0
Timer
‰
Stopwatch function
*The middle hotplate is adjusted on the right-hand control panel
Hotplate Activating and deactivating
$
Single-circuit hot-
plate
ð
Dual-circuit hotplate
Touch the ð symbol
When the hotplate is activated: the corresponding indicator lights up
Operating the appliance en
7
■ With multi-circuit hotplates the heater elements of the
inner filament circuits and the heater element of the
activations may switch on and off at different times.
Combination cooking zone
The single and dual-circuit hotplate can be operated
without the bridge heating element independently of
each other or combined with the bridge heating
element as described in the table.
The small roasting zone (1 + 3) and the single-circuit
hotplate (2) can also be operated independently of
each other with different heat settings. Different
temperature ranges are therefore generated at the large
roaster, the teppan yaki or the grill plate, for example:
the small roasting zone can then be used to fry a meal
and the single-circuit hotplate can simultaneously be
used to keep a meal warm.
Note: Suitable cookware is available from the after-
sales service or our e-Shop.
Residual heat indicator
The hob has a two-stage residual heat indicator for
each hotplate.
If • appears in the display the hob is still hot. It may be
used, for example, to keep a small meal warm or to
melt cooking chocolate. As the hotplate cools down
further, the display changes to œ. The display remains lit
until the hotplate has cooled sufficiently.
1Operating the appliance
Oper at i ng the appl i ance
In this section, you can find out how to set the
hotplates. The table shows heat settings and cooking
times for various meals.
Switching the hob on and off
The main switch is used to switch the hob on and off.
Switching on the appliance
Touch the # symbol. A signal sounds. The indicator
light above the main switch lights up. The control
displays and the heat setting displays ‹ light up. The
hob is ready for use.
The two front hotplates are automatically selected. The
‹ heat setting displays light up brightly.
Switching off the appliance
Touch the
# symbol until the indicator light above the
main switch and the displays go out. All hotplates are
switched off. The residual heat indicator remains on
until the hotplates have cooled down sufficiently.
Notes
■ The hob will switch itself off automatically once all
hotplates have been switched off for a while (10-
60 seconds).
■ The settings remain stored for 4 seconds after the
hob has been switched off. If you switch it on again
during this time, the hob will operate using the
previously stored settings.
Setting a hotplate
Select the desired heat setting on the control panel.
Heat setting 1 = Lowest power
Heat setting 9 = Highest power
Every heat setting has an intermediate setting. It
appears on the display, e.g. as ….†.
Selecting the heat setting
The hob must be on.
1. Touch the ‹ heat setting display to select the
hotplate.
‹ lights up brightly on the heat setting display
2. Select the required heat setting on the control panel.
The hotplate is switched on.
1 = dual-circuit hotplate
2 = single-circuit hotplate
3 = bridge heating element
Combination Activation Suitable for
Small roasting
zone:
Combination of 1
+ 3
With the ˆ symbol activate
the bridge heating element.
ˆ symbol lights up
brightly.
Small roaster
Small teppan yaki
Large roasting
zone:
Combination of 1
+ 3 + 2
Touch the Ô symbol
Ô symbol lights up brightly.
Large roaster
Large teppan yaki
Large grill plate
E
1
2
en Operating the appliance
8
Changing the heat setting:
Select the hotplate and set the required heat setting on
the control panel.
Switching off the hotplate
Select the hotplate. Set the control panel to 0. After
about 10 seconds, the residual heat indicator appears.
Note: The last selected hotplate remains activated. You
can set the hotplate without selecting it again.
Table of cooking times
The following table provides some examples.
Cooking times and heat settings may vary depending
on the type of food, its weight and quality. Deviations
are therefore possible.
For bringing liquids to the boil, use heat setting 9.
Stir thick liquids occasionally.
Food that needs to be seared quickly or food which
loses a lot of liquid during initial frying is best seared in
several small portions.
Tips for energy-saving cooking can be found in the
Environmental protection section.~ Page 5
Ongoing
cooking set-
ting
Ongoing cook-
ing time in
minutes
Melting
Chocolate coating 1-1.5 -
Butter, honey, gelatine 1-2 -
Heating and keeping warm
Stew (e.g. lentil stew) 1-2 -
Milk** 1.5-2.5 -
Heating sausages in water** 3-4 -
Defrosting and heating
Frozen spinach 2.5-3.5 10-20 min
Frozen goulash 2.5-3.5 20-30 min
Poaching, simmering
Dumplings 4.5-5.5* 20-30 min
Fish 4-5* 10-15 min
White sauces, e.g. béchamel
sauce
1-2 3-6 min
Whisked sauces, e.g. sauce Béar-
naise, hollandaise
3-4 8-12 min
Boiling, steaming, braising
Rice (with double the quantity of
water)
2-3 15-30 min
Rice pudding 1.5-2.5 35-45 min
Unpeeled boiled potatoes 4-5 25-30 min
* Ongoing cooking without a lid
** Without lid
*** Turn frequently
Boiled potatoes 4-5 15-25 min
Pasta, noodles 6-7* 6-10 min
Stew, soups 3.5-4.5 15-60 min
Vegetables 2.5-3.5 10-20 min
Frozen vegetables 3.5-4.5 10-20 min
Cooking in a pressure cooker 4-5 -
Braising
Roulades 4-5 50-60 min
Pot roast 4-5 60-100 min
Goulash 2.5-3.5 50-60 min
Frying with little oil**
Escalope, plain or breaded 6-7 6-10 min
Escalope, frozen 6-7 8-12 min
Chop, plain or breaded*** 6-7 8-12 min
Steak (3 cm thick) 7-8 8-12 min
Hamburger, rissoles (3 cm
thick)***
4.5-5.5 30-40 min
Poultry breast (2 cm thick)*** 5-6 10-20 min
Poultry breast, frozen*** 5-6 10-30 min
Fish and fish fillet, plain 5-6 8-20 min
Fish and fish fillet, breaded 6-7 8-20 min
Fish and fish fillet, breaded and
frozen, e.g. fish fingers
6-7 8-12 min
Scampi and prawns 7-8 4-10 min
Sautéing vegetables, fresh mush-
rooms
7-8 10-20 min
Vegetables, meat in Asian-style
strips
7.5-8.5 15-20 min
Stir fry, frozen 6-7 6-10 min
Pancakes 6-7 consecutively
Omelette 3.5-4.5 consecutively
Fried eggs 5-6 3-6 min
Deep-fat frying (150-200 g per
portion continuously in 1-2 li-
tres oil**)
Frozen products, e.g. chips,
chicken nuggets
8-9 -
Croquettes, frozen 7-8 -
Meat, e.g. chicken portions 6-7 -
Fish, breaded or battered 5-6 -
Vegetables, mushrooms, breaded
or battered, tempura
5-6 -
Small baked items, e.g. ring
doughnuts/jam-filled doughnuts,
fruit in batter
4-5 -
Ongoing
cooking set-
ting
Ongoing cook-
ing time in
minutes
* Ongoing cooking without a lid
** Without lid
*** Turn frequently
Frying Sensor en
9
cFrying Sensor
Fr y i ng Sens or
The dual-circuit hotplate marked with the Õ symbol
has a sensor frying system function. If you operate the
hotplate with the sensor frying system, a sensor
regulates the temperature of the pan.
Your advantage when frying:
■ The hotplate only heats up when necessary. This will
save energy.
■ Oil and fat do not overheat.
Notes
■ Never leave fat unattended while you are heating it.
■ Put the pan in the centre of the hotplate. Make sure
that the base of the pan has the correct diameter.
■ Do not place a lid on the pan, otherwise the
regulator will not work. You can use a splatter guard;
it will not prevent the regulator from working.
■ Only use fat that is suitable for frying. For butter,
margarine, extra virgin olive oil or lard, select the
frying setting 1 or 2.
Pans for the sensor frying system
Select the right pan when using the sensor frying
system.
System pans as optional accessories
You can also purchase a frying pan which is ideally
suited to frying using the sensor frying system from your
specialist electrical retailer or at www.siemens
eshop.com: HZ390230
Both availability and whether it is possible to order
online differ between countries.
The frying settings given below have been adjusted to
the system pans.
Note: The sensor frying system may also work with
other pans. Test the pans first with low frying settings,
changing as necessary. The pans may overheat on high
frying settings.
The frying settings
Setting the sensor frying system
Select the appropriate frying setting from the table. Put
the pan on the hotplate.
The hob must be on.
1. Touch the Õ symbol. ‹ lights up in the hotplate
display and the Ý symbol appears.
2. Select the required frying setting on the control
panel. The sensor frying system is activated. The
large dual-circuit hotplate is switched on
automatically.
The Ýsymbol flashes until the frying temperature is
reached. Then a signal sounds. Symbol Ý is lit.
3. Add the fat and then the food to the pan.
Turn as you normally would to prevent burning.
Switching off the sensor frying system
Touch the Õ symbol.
Frying table
The table shows which frying setting is suitable for
which dish. The frying time may depend on the type,
weight, thickness and quality of the food.
The frying settings given are for the system pans. The
frying settings may vary if you use different pans.
First heat the empty pan. Only add the food with the fat
to the pan when the signal sounds.
Frying
setting
Temperature Suitable for
1 very low e.g. cooking and reducing sauces, steam-
ing vegetables without adding water and
with added fat, frying food with extra vir-
gin olive oil, butter or margarine
2 low e.g. omelettes, frying food with extra virgin
olive oil, butter or margarine
3 low - medium e.g. frying fish, thick food such as rissoles
and sausages
4 medium - high e.g. frying steak medium or well done, fro-
zen breaded products, thin food such as
escalopes, strips of meat and vegetables
5 high e.g. frying steak rare, potato fritters and
fried potatoes
Frying
setting
Total frying time after
the signal sounds
Meat
Escalope, plain or breaded 4 6-10 min
Fillet 4 6-10 min
Chop* 3 10-17 min
* Turn frequently
** Place in a cold pan
Í
Î
Í
Î
en PowerBoost function
10
vPowerBoost function
Po we r Boo s t function
PowerBoost lets you heat up large volumes of water
even faster than on heat setting 9.
PowerBoost is only available on hotplates marked with
the boost symbol.
With dual-circuit hotplates the second filament circuit
has to be activated for use with the PowerBoost
function.
Switching on PowerBoost
1. Select the hotplate.
2. Touch the b symbol. The › display lights up.
The PowerBoost function is switched on.
Cordon bleu* 3 15-20 min
Steaks, rare (3 cm thick) 5 6-8 min
Steaks medium or well done
(3 cm thick)
4 8-12 min
Poultry breast (2 cm thick)* 3 10-20 min
Sausages, pre-boiled or raw* 3 8-20 min
Hamburgers (1.5 cm thick)** 3 6-30 min
Rissoles (2 cm thick)** 3 10-20 min
Strips of meat, gyros 4 7-12 min
Minced meat 4 6-10 min
Bacon 2 5-8 min
Fish
Fish, fried, e.g. trout 3 10-20 min
Fish fillet, plain or breaded 3/4 10-20 min
Scampi, prawns 4 4-8 min
Egg dishes
Pancakes 4 continuous frying
Omelettes 2 3-6 min (per portion)
Fried egg 2/4 2-6 min
Scrambled egg 2 4-9 min
Shredded raisin pancake 3 10-15 min
French toast 3 4-8 min (per portion)
Potatoes
Fried potatoes, boiled in their
skin
5 6-12 min
Fried potatoes, made from raw
potatoes
3 15-25 min
Potato fritter 5 2.5-3.5 min (per por-
tion)
Rösti 2 40-45 min
Glazed potatoes 4 10-15 min
Vegetables
Sweat garlic / onions until
transluscent
1/2 2-10 min
Fried onions 3 5-10 min
Courgettes, aubergines 3 4-12 min
Peppers, green asparagus 3 4-15 min
Steaming vegetables with
added fat and without adding
water, e.g. courgettes, green
peppers
1 10-20 min
Mushrooms 4 10-15 min
Glazed vegetables 4 6-10 min
Frozen products
Escalope 4 15-20 min
Frying
setting
Total frying time after
the signal sounds
* Turn frequently
** Place in a cold pan
Cordon bleu 3 10-30 min
Poultry breast * 2 10-30 min
Chicken nuggets* 4 10-20 min
Gyros, kebab 4 10-15 min
Fish fillet, plain or breaded 3 10-20 min
Fish fingers 4 8-12 min
Chips 4/5 4-6 min
Stir fries / stir-fried vegetables 4 8-15 min
Spring rolls 3 10-30 min
Camembert/cheese 3 10-15 min
Sauces
Tomato sauce with vegetables 1 25-35 min
Béchamel sauce 1 10-20 min
Cheese sauce, e.g. Gorgonzola
sauce
1 10-20 min
Reducing sauces, e.g. tomato
sauce, Bolognese sauce
1 25-35 min
Sweet sauces, e.g. orange
sauce
1 15-25 min
Miscellaneous
Camembert/cheese 3 7-10 min
Dried ready meals to which you
add water, e.g. pasta with
sauce*
2 4-6 min
Croutons 3 6-10 min
Toasting almonds / other nuts /
pine nuts**
2 3-7 min
Frying
setting
Total frying time after
the signal sounds
* Turn frequently
** Place in a cold pan
Childproof lock en
11
Switch off PowerBoost
1. Select the cooking zone.
2. Select any ongoing cooking setting. The › display
goes out.
PowerBoost is switched off.
Notes
■ If you do not turn off the PowerBoost function, it
switches off automatically after a certain period of
time. The hotplate switches back to the heat setting
9.
■ Please remember that oil and fat heat up quickly with
PowerBoost. Never leave the hob unattended. Oil
and fat that have overheated will catch fire quickly,
see section "Important safety information".~ Page 4
AChildproof lock
Childproof lock
You can use the childproof lock to prevent children
from switching on the hob.
Switching the childproof lock on and off
The hob must be switched off.
To switch on: Switch on the hob using the main switch
#. Touch the # symbol for 4 seconds. The ‚ display
lights up for 10 seconds. The hob is locked.
To switch off: Switch on the hob using the main switch
#. Touch the # symbol for 4 seconds. The lock is
released.
Automatic childproof lock
This function automatically activates the childproof lock
every time you switch the hob off.
Switching on and off
Find out how to switch the automatic childproof lock on
and off in the Basic settings section.~ Page 13
OTime-setting options
Ti me- s et t i ng opt i ons
There are 3 different time-setting options:
■ A hotplate should switch off automatically
■ Kitchen timer
■ Stopwatch
Automatic hotplate switch-off
Enter a cooking time for the relevant hotplate. When the
cooking time has elapsed, the hotplate switches off
automatically.
Setting the cooking time
The hotplate must be switched on.
1. Touch the symbol 0 2 and then select the hotplate.
The x display lights up. ‹‹ minlights up in the
timer display.
2. Touch the desired presetting in the settings range.
The possible presetting from left to right is 1, 2, 3,
etc. to 9 minutes. Within 10 seconds, slide your
finger along the settings range repeatedly until the
desired cooking time is reached.
The cooking time counts down. If you have set a
cooking time for more than one hotplate, the shortest
cooking time is always displayed.
Sensor frying system
When you cook with the sensor frying system, the set
cooking time only begins when the temperature for the
selected area is reached.
Automatic setting
If you touch settings range presets 1 to 5 for a longer
time, the cooking time automatically counts back down
to one minute.
If you touch settings range presets 6 to 9 for a longer
time, the cooking time automatically counts up to 99
minutes.
When the time has elapsed,
When the cooking time has elapsed, the hotplate
switches off. You will hear an audible signal and
‹‹lights up in the display for 10 seconds. The indicator
x flashes. Touch any symbol. The displays go out and
the audible signal ceases.
Changing or cancelling the cooking time
Touch the symbol 0 2 and then select the hotplate.
Change the cooking time or set to ‹‹ in the settings
range.
Notes
■ You can set a cooking time of up to 99 minutes.
■ If the cooking time has counted down to the last
minute, the timer display changes from minutes to
seconds.
PLQ
[
PLQ
[
[
en Automatic safety cut-out
12
Automatic timer
You can use this function to preselect a cooking time
for all hotplates. Each time a hotplate is switched on,
the pre-selected cooking time then counts down. When
the cooking time has elapsed, the hotplate switches off
automatically.
You can find out how to switch on the automatic timer in
the Basic settings section.~ Page 13
Note: You can change the cooking time for a hotplate
or switch off the automatic timer for the hotplates:
Touch the symbol 0 2 and then select the hotplate.
Change the cooking time or set to ‹‹ in the settings
range.
Kitchen timer
You can use the kitchen timer to set a time of up to 99
minutes. It runs independently of all the other settings.
To activate it the hob must be on.
Setting the kitchen timer
1. Touch the 0 symbol, the V display lights up. ‹‹
min lights up in the timer display.
2. Set the desired time in the settings range.
The timer starts counting down after a few seconds.
When the time has elapsed,
When the time has elapsed, you will hear an audible
signal and ‹‹lights up in the display for 10 seconds.
The indicator V flashes. Touch any symbol. The
displays go out and the audible signal ceases.
Setting the correct time
Use the 0 symbol to select the kitchen timer and reset
the time.
Stopwatch function
The stopwatch function displays the time that has
passed since activating the function.
The stopwatch function only works when the hob is
switched on. When the hob is switched off, the
stopwatch function is switched off as well.
The stopwatch function is switched on by touching the
þ symbol. ‹‹ appears in the timer display and timing
starts. Seconds are displayed during the first minute,
and then minutes.
The stopwatch function is switched off by touching the
þ symbol again. The timer display goes out.
Note: If another time-setting option is selected in
addition to the stopwatch function, the setting appears
in the timer display for 10 seconds. The stopwatch
function is then displayed again.
bAutomatic safety cut-out
Au t o mat i c saf et y cut - out
If a hotplate has been switched on for a long time
without the setting being changed, the automatic time
limit is activated.
The hotplate stops heating. ”‰ and the •/œ residual
heat indicator flash alternately on the hotplate display.
The display goes out when you touch any control. You
can make new settings.
When the time limit is activated depends on the heat
setting selected (1 to 10 hours).
zKeep warm function
Ke e p wa r m function
The Keep warm function is suitable for melting
chocolate or butter and for warming food and cookware
Switching on the Keep warm function
1. Touch the è symbol
2. Select the hotplate. – lights up on the heat setting
display.
The Keep warm function is switched on.
Switching off the Keep warm function
1. Touch the è symbol.
2. Select the hotplate. ‹ lights up on the heat setting
display.
The Keep warm function is switched off.
kWipe protection
Wipe pr ot ect i on
If you wipe over the control panel while the hob is
switched on, settings may be altered.
To prevent this from happening, your hob has a wipe
protection function. Touch the # symbol. An audible
signal sounds. The # symbol lights up. The control
panel is locked for 30 seconds. You can now wipe over
the control panel without altering any settings.
Note: The main switch is excluded from the wipe
protection function. You can switch off the hob at any
time.
Energy consumption indicator en
13
[Energy consumption
indicator
Ener gy consumpt i on indicator
You can use this function to have the total energy
consumption between switching the hob on and off
displayed.
Once switched off, the consumption in kilowatt hours
(e.g. 1.87 kWh) is displayed for 10 seconds
The accuracy of the display depends, amongst other
things, on the voltage quality of the power supply.
The display has not been activated. You can find out
how to activate the display in the Basic settings
section.~ Page 13
QBasic settings
Ba s i c set t i ngs
Your appliance has various basic settings. You can
adapt these settings to suit your own needs.
Changing the basic settings
The hob must be switched off.
1. Switch on the hob.
2. Within the next 10 seconds, touch and hold the 0
symbol for 4 seconds.
The after-sales index will be displayed to begin with.You
can scroll through all the different information from the
setting area:
3. Touch the 0 symbol again
™‚ will appear and ‹ will be lit on the hotplate display.
4. Touch the 0 symbol repeatedly until the required
indicator appears.
Display
screen
Function
™‚
Automatic childproof lock
‹
Switched off.*
‚
Switched on.
ƒ
Manual and automatic childproof lock switched off.
™ƒ
Audible signal
‹
Confirmation signal and operation error signal are
switched off (main switch signal always remains).
‚
Only the operation error signal is switched on.
ƒ
Only the confirmation signal is switched on.
„
Confirmation signal and operation error signal switched
on.*
™„
Energy consumption display (Ask your electricity
supply company what the mains voltage is)
‹
Consumption display switched off.*
‚
Consumption display with mains voltage at 230 V.
ƒ
Consumption display with mains voltage at 400 V.
„
Consumption display with mains voltage at 220 V.
…
Consumption display with mains voltage at 240 V.
*Basic setting
™†
Automatic timer
‹‹
Switched off.*
‹‚-ŠŠ
Cooking time, after which the hotplates switch off.
™‡
Duration of the timer end signal
‚
10 seconds.*
ƒ
30 seconds
„
1 minute.
™ˆ
Activation of the heating elements
‹
Switched off.
‚
Switched on.
ƒ
Last setting before the hotplate was switched off.*
™‹
Reset the basic settings
‹
Switched off.*
‚
Switched on.
Information
screen
After-sales service index (KI)
‹‚
Manufacturing date
”š
Year of manufacture
‚†.
Month of manufacture
‹.†
Display
screen
Function
*Basic setting
en Home Connect
14
5. Set the value you require in the setting area.
6. Touch and hold the 0 symbol for 4 seconds.
The setting is now activated.
Switching off
To exit the basic setting, switch off the hob with the
main switch and make new settings.
oHome Connect
Ho me Connec t
This appliance is WLAN-enabled and settings can be
sent to the appliance via a mobile device.
If the appliance is not connected to the home network,
the appliance functions in the same way as a hob with
no network connection. The hob can always be
operated via the control panel.
The availability of the Home Connect function depends
on the availability of Home Connect services in your
country. Home Connect services are not available in
every country.You can find more information on this at
www.home-connect.com.
Notes
■ Hobs are not designed to be used unattended - you
must always keep an eye on the cooking process.
■ Ensure that you follow the safety instructions in this
instruction manual and that these are also observed
when operating the appliance via the Home Connect
app. You must also follow the instructions in the
Home Connect app.~ "Important safety
information" on page 4
■ Using the Home Connect app, you can send settings
to your appliance and then have to confirm them on
the appliance. It is not possible to operate the
appliance whilst you are away from home.
■ Operation on the appliance always has priority.
During this time, it is not possible to operate the
appliance using the Home Connect app.
Setting up
To implement settings via Home Connect, you must
have installed and set up the Home Connect app on
your mobile device.
Observe the Home Connect documents supplied for
this.
Follow the steps specified by the app to make the
settings.
The app must be open in order to perform the setup
process.
Automatic registration in the home network
You require a router that has WPS functionality.
You require access to your router.If you do not have
this, follow the steps for "Manual registration in the
home network".
1. Switch on the hob.
2. Touch the 0 symbol for 4 seconds.
Product information will be displayed.
3. Touch the 0 symbol repeatedly until the •’‚
setting appears.
‹ lights up on the cooking position display.
4. Set the ‚ value on the control panel.
‚ and the D symbol will flash on the cooking
position display.
5. Press the WPS button on the router within the next
2 minutes.
The hob is connected to the home network if the
D symbol no longer flashes but is lit up on the
cooking position display.
The appliance automatically tries to connect to the
app and the •’ƒ setting appears.The ‚ value
flashes on the control panel.
6. Start the app on the mobile device and follow the
instructions for automatic network registration.
The registration procedure has been completed once
the ‹ value appears on the cooking position display.
Manual registration in the home network
1. Switch on the hob.
2. Touch the 0 symbol for 4 seconds.
Product information will be displayed.
Home Connect en
15
3. Touch the 0 symbol repeatedly until the •’‚
setting appears.
‹ lights up on the cooking position display.
4. Set the ƒ value on the control panel.
ƒ and the D symbol will flash on the cooking
position display.
5. Use the "Home Connect" SSID and the "Home
Connect" key to register the mobile device on the
hob network.
The hob is connected to the home network if the
D symbol no longer flashes but is lit up on the
cooking position display.
The appliance automatically tries to connect to the
app and the •’ƒ setting appears.The ‚ value
flashes on the control panel.
6. Start the app on the mobile device and follow the
instructions for manual network registration.
The registration procedure has been completed once
the ‹ value appears on the cooking position display.
Home Connect settings
You can adjust Home Connect to suit your
requirements at any time.
In the basic settings for your hob, navigate to the Home
Connect settings to display network and appliance
information.
Symbol Function
•’‚
Registration in the home network (WLAN)
‹
Not connected /disconnect network.
‚
Connect automatically.
ƒ
Connect manually.
„
Connected.
•’ƒ
Connection to app
‹
Not connected.
‚
Connect.
•’„
Connect to WLAN
‹
Radio module switched off.
‚
Radio module switched on.
•’…
Settings via app
‹
Switched off.
‚
Switched on.*
•’†
Software update
‚
Update available and ready for installation.
ƒ
Starting installation.
•’‡
Remote access by Customer Service
‹
Not permitted.
‚
Permitted.
•’ˆ
WLAN signal strength
‹
Not connected to home network (WLAN).
‚
Signal strength 1 (poor)
ƒ
Signal strength 2 (moderate)
* Basic setting
en Home Connect
16
Notes
■ The •’ƒ setting is only displayed if the appliance is
connected to the home network.
■ The •’„ setting is only displayed if the appliance
has once connected to a network.
■ The •’† setting is only displayed if an update is
available.
■ The •’‡ setting is only displayed if Customer
Service is attempting to connect to the appliance.
You can end this at any time after granting access.
■ The •’ˆ and •’‰ settings are only displayed if
there is a connection to WLAN.
Deactivating WLAN
If WLAN is activated, you can use the Home Connect
functions.
Note: In networked standby mode, your appliance
requires max. 2 W.
1. Touch the 0 symbol for 4 seconds.
Product information will be displayed.
2. Touch the 0 symbol repeatedly until the •’„
setting appears.
‚ lights up on the cooking position display.
3. Set the ‹ value on the control panel.
WLAN is deactivated and the D symbol on the control
panel goes out.
Disconnecting from the network
Di sconnect i ng from the net wor k
You can disconnect your hob from the network at any
time.
Note: If your hob is disconnected from the network, it is
not possible to operate it using Home Connect.
1. Touch the 0 symbol for 4 seconds.
Product information will be displayed.
2. Touch the 0 symbol repeatedly until the •’‚
setting appears.
„ lights up on the cooking position display.
3. Set the ‹ value on the control panel.
The appliance is disconnected from the home network
and the D symbol on the control panel goes out.
Connecting to the network
Connect i ng to the net wor k
1. Touch the 0 symbol for 4 seconds.
Product information will be displayed.
2. Touch the 0 symbol repeatedly until the •’‚
setting appears.
‹ lights up on the cooking position display.
3. On the control panel
set the "Connect automatically" ‚ value or
or the "Connect manually" ƒ value.
4. Follow the instructions in the section entitled
"Automatic registration in the home network" or
"Manual registration in the home network".
Connect to the app
If the Home Connect app is installed on your mobile
device, you can connect it to your hob.
Notes
■ The appliance must be connected to the network.
■ The app must be open and be set up.
■ If your extractor hood is directly connected, first
disconnect the hob from your home network and
then initiate the connection process
again.~ "Disconnecting from the network"
on page 16~ "Connecting to the network"
on page 16
1. Touch the 0 symbol for 4 seconds.
The product information will be displayed.
2. Touch the 0 symbol repeatedly until the •’ƒ
setting appears.
‹ will be lit on the hotplate display.
3. Set the value ‚ in the settings area.
4. Follow the instructions in the app to complete the
connection process.
Settings via app
Using the Home Connect app, you can easily access
the basic settings for your hob and send settings for the
cooking positions to the hob.
„
Signal strength 3 (good)
•’‰
Connection to Home Connect server
‹
Not connected.
‚
Connected.
Symbol Function
* Basic setting
Home Connect en
17
Notes
■ To change basic settings the hob must be switched
off.
■ Operation on the appliance always has priority.
During this time it is not possible to operate the
appliance using the Home Connect app.
■ The transfer of settings is activated when the
appliance is supplied.
■ If the transfer of settings has been deactivated, only
the hob's operating statuses will be displayed in the
Home Connect app.
1. Touch the 0 symbol for 4 seconds.
Product information will be displayed.
2. Touch the 0 symbol repeatedly until the •’…
setting appears.
3. To activate the transfer, select the ‚ value on the
control panel. To deactivate the transfer, select the ‹
value.
Confirming settings
As soon as cooking settings are transmitted to a
cooking zone, the cooking zone display, timer display
or modified function starts, depending on the setting. To
confirm that you want to use these settings, touch the
indicator for the required hotplate. To discard the
settings, touch any other button on the hob.
Software update
Using the software update function, your hob's software
can be updated (e.g. for the purpose of optimisation,
troubleshooting or security updates). To do this, you
need to be a registered Home Connect user, have
installed the app on your mobile device and be
connected to the Home Connect server.
As soon as a software update is available, you will be
informed by the Home Connect app, from which you will
also be able to download the update.
Once the update has been successfully downloaded,
you can start installing it via the hob (basic settings,
•’† setting) or the Home Connect app if you are on
your local area network.
The Home Connect app will notify you once installation
is complete.
Notes
■ You can continue to use your hob as normal while
updates are downloading.
■ Depending on your personal settings in the app,
software updates can also be set to download
automatically.
■ We recommend that you install security updates as
soon as possible.
About data protection
When your appliance is connected for the first time to a
WLAN network, which is connected to the Internet, your
appliance transmits the following categories of data to
the Home Connect server (initial registration):
■ Unique appliance identification (consisting of
appliance codes as well as the MAC address of the
installed WiFi communication module).
■ Security certificate of the WiFi communication
module (to ensure a secure IT connection).
■ The current software and hardware version of your
domestic appliance.
■ Status of any previous resetting to factory settings.
This initial registration prepares the Home Connect
functions for use and is only required when you want to
use these Home Connect functions for the first time.
Note: Ensure that the Home Connect functions can be
used only in conjunction with the Home Connect app.
Information on data protection can be accessed in the
Home Connect app.
Declaration of Conformity
BSH Hausgeräte GmbH hereby declares that the
appliance which features Home Connect is in
accordance with the basic requirements and the other
relevant provisions of the directive 2014/53/EU.
A detailed RED Declaration of Conformity can be found
online at www.siemens-home.bsh-group.com on the
product page of your appliance with the additional
documents.
2.4 GHz band: max. 100 mW
5 GHz band: max. 100 mW
y
BE BG CZ DK DE EE IE EL
ES FR HR IT CY LV LT LU
HU MT NL AT PL PT RO SI
SK FI SE UK NO CH TR
5 GHz Wi-Fi: for indoor use only
en Hood connection
18
eHood connection
Ho o d connect i on
You can connect this appliance to a suitable extractor
hood and then control the functions of the hood via your
hob.
You have various options for connecting the appliances
together:
Home Connect
Two appliances can be connected using the Home
Connect app provided that both of them are Home
Connect-compatible.
Both appliances can be controlled via the app and via
the control panel.
Refer to the Home Connect documents supplied and
the Home Connect section for more information.
~ "Home Connect" on page 14
Connecting appliances directly
If the appliance is connected directly to an extractor
hood, the extractor hood can be controlled via the hob.
It is then not possible for either of the appliances to
connect to your home network or to the app. Both
appliances can be controlled via the control panel.
Connecting appliances via your home network
Use this type of connection if neither or one of the two
appliances is connected to the Home Connect app.
If the appliances are connected to each other via your
home network, you can use both the hood controls and
Home Connect to operate the hob.
Notes
■ Make sure you follow the safety instructions in the
instruction manual for your extractor hood and that
these are complied with even when operating the
appliance via the hood controls on the
hob.~ "Important safety information" on page 4
■ If the appliance is being operated by means of the
controls on the extractor hood, this mode of
operation always has priority. It is not possible to use
the hood controls on the hob during this time.
■ In networked standby mode, your appliance requires
a maximum of 2 W.
Setting up
To set up the connection between the hob and the
extractor hood, the hob must be switched on.
Connecting directly
Make sure that the extractor hood is switched off.
For more information, refer to the section entitled
"Connecting to the hob" in the instruction manual for
your extractor hood.
Note: If you connect your hob directly to the extractor
hood, it can no longer be connected to your home
network as well and you can no longer use Home
Connect.
1. Touch and hold the 0 symbol for four seconds.
The product information is displayed.
2. Touch the 0 symbol repeatedly until the ™‚‡
setting appears.
‹ lights up in the hotplate display.
3. Set the value ‚ in the settings area.
‚ flashes in the hotplate display.
4. You have two minutes to initiate the connection
process on the extractor hood.
Once the hob is connected to the extractor hood, the
value „ appears in the hotplate display. After you exit
the settings menu, the symbols for the hob-based hood
controls are displayed in the hob's control panel.
Connecting via your home network
You require a router that has WPS functionality.
You require access to your router.If you do not have
this, follow the steps for "Direct connection".
When you begin, make sure that the extractor hood is
connected to the app or is on your home network.
1. Touch the 0 symbol for 4 seconds.
The product information will be displayed.
Hood connection en
19
2. Touch the 0 symbol repeatedly until the ™‚‡
setting appears.
‹ (not connected) or ƒ (connected to home
network) will be lit on the hotplate display.
3. Set the value ‚ in the settings area.
‚ will flash on the hotplate display.
4. If the appliance is not yet connected to your home
network, press the WPS button on the router within
the next 2 minutes.
The hob will be connected to your home network
and the value ƒ will appear on the hotplate display.
The process of connecting to the extractor hood
starts automatically and is active for 2 minutes.
If the appliance is already connected to your home
network, proceed to the next step.
5. Initiate the process for connecting to the extractor
hood.
Once the connection process is complete, the value „
will appear on the hotplate display.The symbols for the
hood controls on the hob are displayed on the hob's
control panel.
Note: Connection can only be established when both
appliances are connected to your home network and
the connection process has been initiated for both of
them. If the connection process has already timed out
for one of the two appliances, try to connect again
(basic settings, ™‚‡ setting).
Resetting connection
You can reset the connections saved for your home
network and extractor hood at any time.
1. Touch the 0 symbol for 4 seconds.
Product information will be displayed.
2. Touch the 0 symbol repeatedly until the ™‚‡
setting appears.
3. Set the ‹ value on the control panel.
Control the hood via the hob
In the basic settings of your hob you can adjust the
behaviour of your extractor hood depending on the
switch-on/off of the hob or individual cooking zones.
~ "Hood control settings" on page 19
You can select other settings using the control panel.
Setting the fan
Switching on
Touch the I symbol.
Setting fan level
Select the fan level.
You can choose between the levels 1, 2 and 3. To
select the intensive levels, touch buttons 4 or 5, or
touch the & button repeatedly until the required intensive
level is set.
Switching off
Select fan level 0.
Setting automatic mode
Switching on
Touch the I symbol until the ‘ symbol appears on the
control panel.
The fan starts up automatically when steam is
produced.
Switching off
Touch the I symbol until the ‘ symbol goes out, or
select another fan level.
Setting the hood lighting
You can switch the hood light on and off via the hob's
control panel.
Touch the = symbol.
Hood control settings
Ho o d cont r ol set t i ngs
You can adapt the hood controls to suit your needs at
any time.
Note: The ™‚‰, ™ƒ‹, ™ƒ‚ and ™ƒƒ settings are only
displayed if the appliance is connected to an extractor
hood.
Symbol Function
™‚‡
Hob-hood connection
‹
Not connected / disconnect.
‚
Connect.
ƒ
Connected to home network (WLAN).
„
Connected to extractor hood.
™‚‰
Automatic fan switch-on
‹
Switched off.
The hood must be switched on manually if needed.
‚
Switched on in automatic mode.*
In automatic mode, the hood switches itself on when a
cooking zone is switched on.
ƒ
Switched on in manual mode.
The hood switches itself on with a default setting when a
cooking zone is switched on.
™ƒ‹
Fan run-on
‹
The fan switches itself off when the hob is switched off.
‚
Switched on in automatic mode.*
ƒ
Switched on with standard fan run-on.
„
No change in settings.
™ƒ‚
Switch light on automatically
‹
Switched off.
‚
Switched on.*
The light switches itself on when the hob is switched on.
™ƒƒ
Switch light off automatically
‹
Switched off.*
‚
Switched on.
The light switches itself off when the hob is switched off.
* Basic setting
en Cleaning
20
DCleaning
Cl eani ng
Suitable maintenance and cleaning products can be
purchased from the after-sales service or in our e-Shop.
Ceramic
Clean the hob after each use. This will prevent spills
from burning onto the ceramic.
Only clean the hob when it has cooled down sufficiently.
Use only cleaning agents which are suitable for glass
ceramic. Follow the cleaning instructions on the
packaging.
Never use:
■ Undiluted washing-up liquid
■ Detergent intended for dishwashers
■ Scouring agents
■ Harsh cleaning agents such as oven spray or stain
remover
■ Abrasive sponges
■ High-pressure cleaners or steam jet cleaners
Ground-in dirt can be best removed with a glass
scraper, available from retailers. Please note the
manufacturer's instructions.
You can also obtain a suitable glass scraper from our
after-sales service or from the e-Shop.
Using special sponges to clean glass ceramic achieves
great cleaning results.
Hob surround
To prevent damage to the hob surround, observe the
following instructions:
■ Use only hot soapy water.
■ Wash new sponge cloths thoroughly before use.
■ Do not use any sharp or abrasive agents.
■ Do not use the glass scraper.
3Trouble shooting
Tr oubl e shoot i ng
Faults often have simple explanations. Please read the
notes in the table before calling the after-sales service.
The electronics of your hob are underneath the control
panel. For various reasons, the temperature in this area
may rise sharply.
In order that the electronics do not overheat, the
hotplates are switched off as and when necessary. The
”ƒ, ”…, or ”† display appears alternately with the • or
œ residual heat indicator.
Display Fault Measure
None The power supply has been disconnected. Check the household fuse for the appliance. Check whether there is a
power cut by trying other electronic appliances.
All displays flash The touch control is wet or an object is resting
on it.
Dry the control or remove the object.
”ƒ
Several hotplates have been used over a pro-
longed period at high power settings. To pro-
tect the electronics, the hotplate has been
switched off.
Wait a while. Touch any touch control. When ”ƒ goes out, the electronics
have cooled down sufficiently. You can continue cooking.
”… Despite the switch-off by ”ƒ, the electronics
have become hot again. All hotplates have
therefore been switched off.
Wait a while. Touch any touch control. When ”… goes out, you can con-
tinue cooking.
Ӡand the heat setting
flash alternately. An
audible signal can be
heard
Warning: There is a hot pan in the area of the
control panel. There is a risk that the electron-
ics will overheat.
Remove the pan. The fault display goes out shortly afterwards. You can
continue cooking.
Ӡand audible signal
There is a hot pan in the area of the control
panel. To protect the electronics, the hotplate
has been switched off.
Remove the pan. Wait a while. Touch any control. When Ӡ goes out, you
can continue cooking.
”‰
The hotplate was in operation for too long and
has switched itself off.
You can switch the hotplate back on again immediately.
š“ The hotplates do
not heat up
Demo mode is switched on Switching off the demo mode: Disconnect the appliance for 30 seconds
from the power supply (switch off the household fuse or the circuit breaker
in the fuse box). Touch any touch control after 3 minutes. The demo mode
is switched off.
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
Siemens ET875LMV1D/06 Manuale utente
- Categoria
- Piani cottura
- Tipo
- Manuale utente
- Questo manuale è adatto anche per
in altre lingue
- English: Siemens ET875LMV1D/06 User manual
Documenti correlati
-
Siemens Electric Hob Manuale utente
-
Siemens ET675LMP1D/03 Manuale utente
-
Siemens ET975LMP1D/01 Manuale utente
-
Siemens ET975LVV1M Manuale utente
-
-
-
-
-
-