Simplicity 10.5HP AND 30IN Manuale utente

Marca: Simplicity

Modello: 10.5HP AND 30IN

Categoria: Tosa erba

Tipo: Manuale utente

Operator’s Manual – Lawn Tractor

Návod k použití - Sekačka na trávu

Betjeningsmanual - Græsslåmaskine

Bedienungsanleitung – Rasenmäher

Εγχειρίδιο χειριστή - Τρακτέρ χορτοταπήτων

Kasutajajuhend - Murutraktor

Käyttöohje – Ruohonleikkur

Manuel d’utilisation - Tondeuse à gazon

Használati útmutató - Gyep traktor

Manuale per l’operatore – Rasaerba

Gebruikershandleiding - Grasmaaier

Bruksanvisning - Gressklipper

Instrukcja obsługi - Kosiarka do trawy

Руководство по эксплуатации - Садовый трактор

Návod na obsluhu - Snehové frézy

Bruksanvisning – Gräsklippa

Model No. 309007x51C

Mfg. No. Description

7800531 Murray CE Riding Mower

Manual No. 1742447

Revision A

Rev. Date 03/2009

Not for

Reproduction

4 (17x47)

5 (1001054)

6 (2x82)

7 (14x79)

6 (2x82)

6 (17x146)

7 (25x3)

Not for

Reproduction

910

11 12

Not for

Reproduction

17 18

13 14

15 16

9/16

Not for

Reproduction

19 20

Not for

Reproduction

22 23

Not for

Reproduction

10 10

Not for

Reproduction

12 3 456

789

MAX 90N

+MAX 150N

10 11

12 13

1234567

10 11 12 13 14 15

1001054

2x82 14x79

17x47

327349

17x146

25x3

Not for

Reproduction

1742447 9

INTERNATIONAL PICTORIALS

IMPORTANT: The following pictorials are

located on your unit or on literature supplied

with the product. Before you operate the

unit, learn and understand the purpose for

each pictorial.

NOTE: Illustrations and pictorials begin on

page 2.

Safety Warning Pictorials (Figure 25)

1WARNING

2IMPORTANT: Read Owner’s Manual Before

Operating This Machine.

3WARNING: Thrown Objects. Keep

Bystanders Away. Read User Instructions

Before Operating This Machine.

4WARNING: Do Not Use This Machine On

Slopes Greater Than 10 Degrees.

5DANGER: Keep People, Especially

Children, Away From Unit.

6DANGER: No Step.

7DANGER: Keep Feet And Hands Away

From Rotating Blade.

8DANGER: Disconnect Spark Plug Wire

Before Servicing Unit.

9WARNING: Hot Surface.

10 WARNING: Use Caution When Connecting

Or Disconnecting Accessories.

11 WARNING: Crushed Fingers.

12 IMPORTANT: Follow Instructions In Owner’s

Manual To Level The Deck.

13 WARNING: Stay Clear Of Mower Blade As

Long As Engine Is Running.

Control And Operating Pictorials

(Figure 26)

1Engine Start

2Lights

3Engine Run

4Engine Stop

5Engine Run

6Brake

7Parking Brake

8Clutch

9Slow

10 Fast

11 Choke

12 Oil

13 Blade Rotation Control

14 Raise

15 Fuel

CONTENTS

INTERNATIONAL PICTORIALS 9

OWNER’S INFORMATION 10

SAFE OPERATION PRACTICES 10

ASSEMBLY 11

OPERATION 12

MAINTENANCE CHART 15

MAINTENANCE 15

TROUBLESHOOTING CHART 18

LIMITED WARRANTY 19

Not for

Reproduction

OWNER’S INFORMATION

Know your product: If you understand the unit

and how the unit operates, you will get the best

performance. As you read this manual, compare

the illustrations to the unit. Learn the location

and the function of the controls. To help prevent

an accident, follow the operating instructions

and the safety rules. Keep this manual for future

reference.

WARNING: Look for this symbol to indicate

important safety precautions. This symbol

indicates: “Attention! Become Alert! Your

Safety Is At Risk.”

Responsibility Of The Owner

WARNING: This cutting machine is

capable of amputating hands and feet

and throwing objects. Failure to

observe the following safety instructions

could result in serious injury or death to the

operator or bystanders.

The responsibility of the owner is to

follow the instructions below.

SAFE OPERATION PRACTICES

For Ride-On (Riding)

Rotary Mower Machines

Training

1. Read the instructions carefully. Be familiar

with the controls and the proper use of the

equipment.

2. Never allow children or people unfamiliar

with these instructions to use the mower.

Local regulations may restrict the age of the

operator.

3. Never mow while people, especially

children, or pets are nearby.

4. Keep in mind that the operator or user is

responsible for accidents or hazards

occurring to other people or their property.

5. Do not carry passengers.

6. All drivers should seek and obtain

professional and practical instruction. Such

instruction should emphasize:

a. the need for care and concentration

when working with ride-on machines;

b. control of a ride-on machine sliding on a

slope will not be regained by the

application of the brake. The main

reasons for loss of control are:

• insufficient wheel grip;

• being driven too fast;

• inadequate braking;

• the type of machine is unsuitable

for its task;

• lack of awareness of the effect of

ground conditions, especially

slopes;

• incorrect hitching and load

distribution.

Preparation

1. While mowing, always wear substantial

footwear and long trousers. Do not operate

the equipment when barefoot or wearing

open sandals.

2. Thoroughly inspect the area where the

equipment is to be used and remove all

objects which may be thrown by the

machine.

3. WARNING - Petrol is highly flammable.

a. Store fuel in containers specifically

designed for this purpose.

b. Refuel outdoors only and do not smoke

while refuelling.

c. Add fuel before starting the engine.

Never remove the cap of the fuel tank

or add petrol while the engine is running

or when the engine is hot.

d. If petrol is spilled, do not attempt to start

the engine but move the machine away

from the area of spillage and avoid

creating any source of ignition until

petrol vapours have dissipated.

e. Replace all fuel tanks and container

caps securely.

4. Replace faulty silencers.

5. Before using, always visually inspect to see

that the blades, blade bolts and cutter

assembly are not worn or damaged.

Replace worn or damaged blades and bolts

in sets to preserve balance.

6. On multi-blade machines, take care as

rotating one blade can cause other blades

to rotate.

Operation

1. Do not operate the engine in a confined

space where dangerous carbon monoxide

fumes can collect.

2. Mow only in daylight or in good artificial

light.

3. Before attempting to start the engine,

disengage all blade attachment clutches

and shift into neutral.

4. Do not use on slopes of more than 10

degrees.

5. Remember there is no such thing as a

“safe” slope. Travel on grass slopes

requires particular care. To guard against

overturning:

a. do not stop or start suddenly when

going up or downhill;

b. engage clutch slowly, always keep

machine in gear, especially when

travelling downhill;

c. machine speeds should be kept low on

slopes and during tight turns;

d. stay alert for humps and hollows and

other hidden hazards;

e. never mow across the face of the slope,

unless the mower is designed for this

purpose.

6. Use care when pulling loads or using heavy

equipment.

a. Use only approved drawbar hitch

points.

b. Limit loads to those you can safely

control.

c. Do not turn sharply. Use care when

reversing.

d. Use counterweight(s) or wheel weights

when suggested in the Instruction Book.

7. Watch out for traffic when crossing or near

roadways.

8. Stop the blades rotating before crossing

surfaces other than grass.

9. When using any attachments, never direct

discharge of material toward bystanders nor

allow anyone near the machine while in

operation.

10. Never operate the mower with defective

guards or shields, or without safety

protective devices in place.

11. Do not change the engine governor settings

or overspeed the engine. Operating an

engine at excessive speed may increase

the hazard of personal injury.

12. Before leaving the operator’s position

a. disengage the power take-off and lower

the attachments;

b. change into neutral and set the parking

brake;

c. stop the engine and remove the key.

13. Disengage drive to attachments, stop the

engine, and disconnect the spark plug

wire(s) or remove the ignition key

a. before cleaning blockages or

unclogging chute;

b. before checking, cleaning or working on

the mower;

c. after striking a foreign object. Inspect

the mower for damage and make

repairs before restarting and operating

the equipment;

d. if the machine starts to vibrate

abnormally (check immediately).

14. Disengage drive to attachments when

transporting or not in use.

15. Stop the engine and disengage drive to

attachment

a. before refuelling;

b. before removing the grass catcher;

c. before making height adjustment unless

adjustment can be made from the

operator’s position.

16. Reduce the throttle setting during engine

run-out and, if the engine is provided with a

shut-off valve, turn the fuel off at the

conclusion of mowing.

17. Before and when backing, look behind and

down for small children.

18. Use extra care when approaching blind

corners, shrubs, trees or other objects that

may obscure vision.

Maintenance and Storage

1. On multi-blade machines, take care as

rotating one blade can cause other blades

to rotate.

2. When machine is to be parked, stored or left

unattended, lower the cutting means unless

a positive mechanical lock is used.

3. Keep all nuts, bolts, and screws tight to be

sure the equipment is in safe working

condition.

4. Never store the equipment with petrol in the

tank inside a building where fumes may

reach an open flame or spark.

5. Allow the engine to cool before storing in

any enclosure.

6. To reduce the fire hazard, keep the engine,

silencer, battery compartment and petrol

storage area free of grass, leaves, or

excessive grease.

7. Check the grass catcher frequently for wear

or deterioration.

8. Replace worn or damaged parts for safety.

9. If the fuel tank has to be drained, this should

be done outdoors.

Not for

Reproduction

ASSEMBLY

All fasteners are in the parts bag. Do not discard

any parts or material until the unit is assembled.

WARNING: Before doing any

assembly or maintenance to the

mower, remove the wire from the

spark plug.

NOTE: In this instruction book, left and right

describe the location of a part with the

operator on the seat.

NOTE: Illustrations and pictorials begin on

page 2.

NOTE: To assemble the following loose

parts, use the fasteners shown at full size in

Figure 27.

How To Install The Seat (Figure 1)

1. Carefully remove the plastic bag from the

seat (1).

2. Raise the seat support (2) and secure in

the UP position with the seat support rod

(6).

3. Align the holes in the seat (1) to the holes in

the seat support (2). Fasten the seat (1) to

the seat support (2) with the fasteners (4)

and (5).

4. Check the operating position of the seat (1).

If the seat (1) needs to be adjusted, loosen

the two wing bolts (5). Slide the seat (1)

forward or backward along the seat

adjusting holes (3). Tighten the wing bolts

(5).

How To Assemble The Steering Wheel

(Figure 2)

1. Make sure the front wheels point forward.

2. Slide the tube (1) into the console (2).

Make sure the end of the tube (1) fits over

the steering bushing (3).

3. Attach the steering wheel (4) to the

steering post (5) with screw (7) and

washer (6).

4. Slide the steering wheel (4) and steering

post (5) into the tube (1) and console (2).

Push on the steering wheel (4). The

steering post (5) will lock onto the pinion

gear. Pull on the steering wheel (4). Make

sure that the steering post (5) is locked in

place.

5. Some models have an optional insert (8) in

the parts bag. Attach the insert (8) to the

centre of the steering wheel (4).

Maintenance Free Battery (Figure 3)

IMPORTANT: Before you attach the battery

cables to the battery, check the battery date.

The battery date tells if the battery must be

charged.

1. Raise the seat support and secure in the UP

position with the seat support rod.

2. Check the top of the battery (1) for the

location of the battery date.

3. If the battery (1) is put into service before

the battery date, the battery cables can be

attached without charging the battery (1).

See “How To Install The Battery Cables”.

4. If the battery (1) is put into service after the

battery date, the battery (1) must be

charged. See “How To Charge The

Maintenance Free Battery”.

How To Charge The Battery (Figure 3)

WARNING: When you charge the

battery, do not smoke. Keep the

battery away from any sparks. The

fumes from the battery acid can cause an

explosion.

1. To disconnect the battery retainer (2) from

the battery tray (3), push in on the lower

end of the battery retainer (2).

2. Remove the battery (1) from the right side

of the unit.

3. Remove the protective cap from the battery

terminal.

4. Use a 12 volt battery charger to charge the

battery (1). Charge at a rate of 6 amperes

for one hour. If you do not have a battery

charger, have an authorized service centre

charge the battery.

5. Install the battery (1) and secure with the

battery retainer (2). Make sure the

positive (+) terminal (4) is on the right

side.

How To Install The Battery Cables

(Figure 3)

WARNING: To prevent sparks, fasten

the red cable to the positive (+)

terminal before you connect the black

cable.

1. Remove the protective cap from the battery

terminal.

2. Fasten the red cable (5) and terminal

cover (9) to the positive (+) terminal (4)

with the fasteners (6) and (7).

3. Fasten the black cable (8) to the negative

(-) terminal with the fasteners (6) and (7).

Check The Tires

Check the air pressure in the tires. Tires with too

much air pressure will cause the unit to ride

rough. Also, the wrong air pressure will keep the

mower housing from cutting level. The correct

air pressure is shown on the side of the tire.

Check The Level Of The Mower Housing

Make sure the level of cut is still correct. After

you mow a short distance, look at the area that

was cut. If the mower housing does not cut

level, see the instructions on “How To Level The

Mower Housing” in the Maintenance section of

this instruction book.

How To Prepare The Engine

NOTE: The engine was shipped from the

factory filled with oil. Check the level of the

oil. Add oil as needed.

See the engine manufacturer’s instructions for

the type of petrol and oil to use. Before you use

the unit, read the information on safety,

operation, maintenance, and storage.

WARNING: Follow the engine

manufacturer’s instructions for the

type of petrol and oil to use. Always

use a safety petrol container. Do not smoke

when adding petrol to the engine. When

inside an enclosure, do not fill with petrol.

Before you add petrol, stop the engine. Let

the engine cool for several minutes.

Important! Before You Start Mowing

❐

Check the engine oil.

❐

Fill the fuel tank with petrol.

❐

Check the level of the mower

housing.

❐

Check the air pressure of the tyres.

❐

Attach the battery cables.

Final Assembly

1. Check all fasteners. Make sure all fasteners

are properly installed and are tight.

2. Check installation. Make sure all parts are

correctly installed.

WARNING: Make sure that the grass

bagger is properly assembled and

correctly installed. The Grass Bagger

must only be used when fully assembled and

correctly installed.

Not for

Reproduction

OPERATION

NOTE: Illustrations and pictorials begin on

page 2.

Location Of Controls (Figure 4)

Blade Rotation Control (1): Use the blade

rotation control to start and stop the rotation of

the blade.

Clutch / Brake Pedal (2): The pedal has two

functions. The first function is a clutch. The

second function is a brake.

Ignition Switch (3): Use the ignition switch to

start and stop the engine.

Speed Control Lever (4): The speed and

direction of travel is controlled by the speed

control lever. Use the speed control lever to

select either forward or reverse.

Lift Lever (5): Use the lift lever to change the

height of cut.

Parking Brake Lever (6): Use the parking

brake lever to engage the brake when you leave

the unit.

Throttle Control Lever (7): Use the throttle

control lever to increase or decrease the speed

of the engine.

Attachments

This unit can use many different attachments. This

unit can pull attachments like a lawn sweeper, a

lawn aerator, or a hopper spreader. This unit can

not use attachments that engage the ground like a

plough, a disk harrow, or a cultivator.

For trailer and pull-behind attachments, the

maximum weight is 90 kg (200 lbs).

Do not operate on a slope that is greater than

10 degrees when using a pull-behind

attachment or trailer.

How To Use The Throttle Control

(Figure 4 and Figure 5)

Use the throttle/choke control (7) to increase

or decrease the speed of the engine.

1. Move the throttle/choke control (7)

completely forward to the CHOKE position

to start a cold engine.

2. The FAST position is marked with a detent.

For normal operation and when using a

grass bagger, move the throttle control to

the FAST position. For maximum charging

of the battery and for a cooler running

engine, operate the engine in the FAST

position.

3. The engine governor is set at the factory for

maximum performance. Do not adjust the

governor to increase the speed of the

engine.

How To Use The Blade Rotation Control

(Figure 4 and Figure 6)

Use the blade rotation control (1) to engage

the blade(s).

1. Before you start the engine, make sure the

blade rotation control (1) is in the

DISENGAGE position (8).

2. To rotate the blade, move the blade

rotation control (1) forward to lock the

blade in the ENGAGE position (9).

3. To stop the blade, move the blade rotation

control (1) to the DISENGAGE position

(8). Before you leave the operator’s

position, make sure the blade(s) has

stopped rotating.

4. Before you ride the unit across a sidewalk

or a road, move the blade rotation control

(1) to the DISENGAGE position.

WARNING: Always keep your hands

and feet away from the blade,

deflector opening, and the mower

housing when the engine runs.

How To Engage The Transmission

To allow the unit to be pushed, it was shipped

with the automatic drive disconnect in the

PUSH position (A, Figure 7). Before operating,

the automatic drive disconnect must be set in

the DRIVE position (B, Figure 7).

1. The engine must be off.

2. The automatic drive disconnect is located

under the left side of the seat deck, next to

the hydrostatic transaxle.

3. To engage the transmission, unlatch the

automatic drive disconnect. The trans-

mission is now connected and ready to

operate.

4. To release the transmission and push the

unit, pull and twist the automatic drive

disconnect. Latch the automatic drive

disconnect in the PUSH position (A, Figure

7). The transmission is now released and the

unit can be pushed.

NOTE: In cold weather, the heavy viscosity

oil in the transmission will make the unit

difficult to push.

How To Use The Speed Control Lever

The Hydrostatic Drive is very easy to operate.

The drive system has a clutch/brake pedal on

the left side (Figure 8) and a speed control

lever on the right side (Figure 10).

To Drive Forward:

1. The automatic drive disconnect must be in

the DRIVE position (B, Figure 7).

2. Completely push the clutch/brake pedal

forward to stop the unit (see Figure 8). Keep

your foot on the pedal.

3. Move the speed control lever to the

NEUTRAL position (see Figure 10).

4. Slowly release your foot from the

clutch/brake pedal (see Figure 8). Do not

keep your foot on the pedal.

5. Move the throttle control to the FAST

position (see Figure 9).

6. Slowly push the speed control lever

forward to the desired speed (see Figure

10). To reduce forward speed, slowly pull the

speed control lever to the desired speed.

To Drive in Reverse:

1. Always disengage blades and look down

and behind before and while backing.

2. Move the speed control lever to the

NEUTRAL position (see Figure 10).

3. To go backward, move the speed control

lever to the REVERSE position.

How To Use The Parking Brake

(Figure 7)

1. Completely push the clutch/brake pedal

(2) forward.

2. Lift the parking brake lever (6).

3. Remove your foot from the clutch/brake

pedal (2) and then release the parking

brake lever (6). Make sure the parking

brake will hold the unit.

4. To release the parking brake (6),

completely push the clutch/brake pedal (2)

forward. The parking brake will

automatically release.

WARNING: Before you leave the

operator’s position, move the shift

lever to the neutral (N) position. Set

the parking brake. Move the blade rotation

control to the DISENGAGE position. Stop the

engine and remove the ignition key.

How To Change The Cutting Height

(Figure 11)

To change the cutting height, raise or lower the

lift lever (5) as follows.

1. Move the lift lever (5) forward to lower the

mower housing and back to raise the mower

housing.

2. When you ride on a sidewalk or road, move

the lift lever (5) to the highest position and

move the blade rotation control (1) to the

DISENGAGE position.

How To Stop The Unit (Figure 4)

1. Completely push the clutch/brake pedal

(2) forward to stop the unit. Keep your foot

on the pedal.

2. Move the blade rotation control (1) to the

DISENGAGE position.

3. Move the shift lever (4) to the NEUTRAL

position.

4. Set the parking brake (6).

WARNING: Make sure the parking

brake will hold the unit.

5. Move the throttle control (7) to the SLOW

position.

6. To stop the engine, turn the ignition key (3)

to the OFF position. Remove the key.

How To Transport The Unit

To transport the unit, follow the steps below.

1. Move the blade rotation control to the

DISENGAGE position.

2. Raise the lift lever to the highest position.

3. Move the throttle control to a position

between SLOW and FAST.

4. To go faster, move the shift lever to a faster

speed.

Not for

Reproduction

How To Install The Side Discharge

Attachment (Figure 12)

WARNING: To prevent the engine

from starting, disconnect the wire

from the spark plug. Make sure the

attachment clutch/blade rotation control is in

the DISENGAGE position.

The mulcher cover (1) lets you mulch the grass

for a clean, fine cut. To discharge the grass out

the side, install the side discharge attachment

(2) as follows.

1. Remove the two wingnuts (3) that secure

the mulcher cover (1).

2. Lift the mulcher cover (1). Mount the side

discharge attachment (2) onto the same

bolts that secured the mulcher cover (1).

3. Secure the side discharge attachment (2)

with the wingnuts (3).

4. To mulch, remove the side discharge

attachment (2) and mount the mulcher

cover (1) to the mower housing with the

wingnuts (3).

How To Operate With The Mower

Housing

WARNING: The mulch cover is a

safety device. Do not remove the

mulch cover. The deflector forces the

discharged material toward the ground.

Always keep the deflector in the down

position. If the deflector is damaged, replace

the deflector with an original equipment part

from an authorized service centre.

IMPORTANT: When you operate with the

mower housing, always operate with the

throttle control in the FAST position.

1. Start the engine.

2. Move the lift lever to a height of cut position.

In high or thick grass, cut the grass in the

highest position first and then lower the

mower housing to a lower position.

3. Move the throttle control to the SLOW

position.

4. Slowly move the blade rotation control to

the ENGAGE position.

5. Push the clutch/brake pedal completely

forward.

6. Move the shift lever to one of the speed

settings.

NOTE: When you mow in heavy grass or

mow with a bagger, put the shift lever in

the slowest speed.

7. Slowly release the clutch/brake pedal.

8. Move the throttle control to the FAST

position. If you need to go faster or slower,

stop the unit and move the shift lever to

another speed setting.

9. Make sure the level of cut is still correct.

After you mow a short distance, look at the

area that was cut. If the mower housing

does not cut level, see the instructions on

“How To Level The Mower Housing” in the

Maintenance section.

WARNING: For better control of the

unit, select a safe speed.

How To Operate On Hills

WARNING: Do not ride up or down

slopes that are too steep to back

straight up. Never ride the unit across

a slope.

1. Before you ride up or down a hill, move the

shift lever to the slowest speed.

2. Do not stop or change speed settings on a

hill. If you must stop, quickly push the

clutch/brake pedal forward and set the

parking brake.

3. To start again, make sure the shift lever is in

the slowest speed. Move the throttle control

to the SLOW position. Slowly release the

pedal.

4. If you must stop or start on a hill, always

have enough space for the unit to roll when

you release the brake and engage the

clutch.

5. Be very careful when you change directions

on a hill. When on a slope or in a turn on a

hill, move the throttle control to the SLOW

position to help prevent an accident.

Before Starting The Engine

Check The Oil

NOTE: The engine was shipped from the

factory filled with oil. Check the level of the

oil. Add oil as needed. See the engine

manufacturer’s instructions for the type of

petrol and oil to use.

1. Make sure the unit is level.

NOTE: Do not check the level of the oil

while the engine runs.

2. Check the oil. Follow the procedure in the

engine manufacturer’s instructions.

3. If necessary, add oil until the oil reaches the

FULL mark on the dipstick. The quantity of

oil needed from ADD to FULL is shown on

the dipstick. Do not add too much oil.

Add Petrol

WARNING: Always use a safety petrol

container. Do not smoke when adding

petrol to the fuel tank. Do not add

petrol when you are inside an enclosure.

Before you add petrol, stop the engine and

let the engine cool for several minutes.

(Figure 13) Fill the fuel tank (1) to the FULL (2)

position with regular unleaded petrol. Do not use

premium unleaded petrol. Make sure the petrol

is fresh and clean. Leaded petrol will increase

deposits and shorten the life of the valves.

How To Start The Engine

WARNING: The electrical system has

an operator presence system that

includes a sensor switch for the seat.

These components tell the electrical system

if the operator is sitting on the seat. This

system will stop the engine when the

operator leaves the seat. For your

protection, always make sure this system

operates correctly.

NOTE: The engine will not start unless you

depress the clutch/brake pedal and move the

blade rotation control to the DISENGAGE

position.

1. Push the clutch/brake pedal completely

forward. Keep your foot on the pedal.

2. Move the shift lever to the neutral (N)

position.

3. Make sure the blade rotation control is in

the DISENGAGE position.

4. Move the throttle control completely forward

to the CHOKE or FAST position. Some

models have a separate choke knob. Pull

the choke knob to the full CHOKE position.

5. Turn the ignition key to the START position.

NOTE: If the engine does not start after

four or five tries, move the throttle

control to the FAST position. Again try to

start the engine. If the engine will not

start, see the TROUBLE SHOOTING

CHART.

6. Slowly move the throttle control to the

SLOW position.

7. To start a hot engine, move the throttle

control to a position between FAST and

SLOW.

Not for

Reproduction

Mowing And Bagging Tips

1. For a lawn to look better, check the cutting

level of the mower housing. See “How To

Level The Mower Housing” in the

Maintenance section.

2. For the mower housing to cut level, make

sure the tyres have the correct amount of air

pressure.

3. Every time you use the unit, check the

blade. If the blade is bent or damaged,

immediately replace the blade. Also, make

sure the nut for the blade is tight.

4. Keep the blade(s) sharpened. Worn blades

will cause the ends of the grass to turn

brown.

5. Do not cut or bag grass that is wet. Wet

grass will not discharge correctly. Let the

grass dry before cutting.

6. Use the left side of the mower housing to

trim near an object.

7. Discharge the cut grass onto the mowed

area. The result is a more even discharge of

cut grass.

8. When you mow large areas, start by turning

to the right so that the cut grass will

discharge away from shrubs, fences,

driveways, etc. After one or two rounds,

mow in the opposite direction making left

turns until finished.

9. If the grass is very high, cut two times to

decrease the load on the engine. First cut

with the mower housing in the highest

position and then lower the mower housing

for the second cut.

10. For better engine performance and an even

discharge of the cut grass, always operate

the engine with the throttle in FAST position.

11. When you use a bagger, operate the engine

with the throttle in FAST position and the

shift lever in first or second gear.

12. For better cutting performance and a quality

cut, mow with the shift lever in one of the

slower speeds.

13. After each use, clean the bottom and top of

the mower housing for better performance.

Also, a clean mower housing will help

prevent a fire.

Mulching Tips

When you use a mulcher attachment, the grass

is cut into very small pieces. These small pieces

will quickly break down. Because the nutrients

are returned to the soil, the lawn will need less

fertilizer. To correctly mulch the grass, follow the

steps below.

1. Set the throttle in the FAST position.

Operate the mower at a slower ground

speed. If ground speed is too fast, the grass

will not have an even cut.

2. Keep a sharp edge on the blade. A blade

that is not sharp will cause the ends of the

grass to become brown.

3. Make sure the grass is dry. Wet grass is

difficult to cut.

4. Set the height of the mower housing so that

only the top third of the grass is cut. If the

grass is too high, set the height of the

mower housing to the maximum height.

Then, lower the mower housing for the

second cut. Also, instead of using the full

width of the mower housing, mulch at half

the width.

5. Clean the bottom of the mower housing.

Grass and other debris can keep the mower

from working correctly.

6. If the grass grows fast, mulch more often.

7. If an area needs improvement, mulch a

second time.

Not for

Reproduction

MAINTENANCE CHART

FREQUENCY MAINTENANCE REQUIRED COMMENTS

Daily or before each use Maintenance engine. Refer to the Engine Owner’s Manual.

Examine blade(s). Check for cracks, wear, and excessive damage.

Remove debris from unit and mowing area.

Examine all rotating and sliding parts.

Check tire inflation. Refer to the Maintenance section.

Verify that the mower housing is level. Refer to the Maintenance section.

Examine V-belts. Check for cracks, wear, and excessive damage.

Check brake operation. Refer to the Operation and Maintenance sections.

After completion of first

5 hours Change oil. Refer to the Engine Owner’s Manual.

After 25 hours Maintenance engine. Refer to the Engine Owner’s Manual.

Remove, examine, sharpen, and balance blade(s). Refer to Maintenance section.

Check adjustments:

a. Blade Rotation Control

b. Brake

c. Clutch

d. Steering

Refer to Maintenance section.

Lubricate chassis and mower housing. Refer to Where to Lubricate instructions.

Check the muffler:

a. Torque

b. For wear or burn out

c. Condition of spark arrestor (if applicable).

Refer to Maintenance section.

Before storage of 30 days

or more Prepare engine for storage. Refer to the Engine Owner’s Manual.

Drain fuel system. Refer to warnings in the Owner’s Manual.

Add fuel stabilizer. Refer to the Engine Owner’s Manual.

Prepare battery for storage:

a. Remove from unit.

b. Fully charge.

c. Move to cool dry place.

MAINTENANCE

NOTE: Illustrations and pictorials begin on

page 2.

General Recommendations

1. The owner’s responsibility is to maintain this

product. This will extend the life of the

product and is also necessary to maintain

warranty coverage.

2. Check the spark plug, drive brake, lubricate

the unit, and clean the air filter once a year.

3. Check the fasteners. Make sure all

fasteners are tight.

4. Follow the Maintenance section to keep the

unit in good operating condition.

WARNING: Before you make an in

spection, adjustment, or repair to the

unit, disconnect the wire to the spark

plug. Remove the wire from the spark plug to

prevent the engine from starting by accident.

NOTE: Torque is measured in foot pounds

(metric Nm). This measurement describes

how tight a nut or bolt must be. The torque is

measured with a torque wrench.

Inspect Blade (Figure 14)

WARNING: Before you inspect or

remove the blade, disconnect the wire

to the spark plug. If the blade hits an

object, stop the engine. Check the unit for

damage. The blade has sharp edges. When

you hold the blade, use gloves or cloth

material to protect your hands.

If you keep the blade (1) sharp and inspect the

blade for damage, the blade will cut better and

be more safe to operate. Frequently check the

blade for excessive wear, cracks, or other

damage. Frequently check the nut (3) that holds

the blade (1). Keep the nut (3) tight. If the blade

hits an object, stop the engine. Disconnect the

wire to the spark plug. See if the blade is bent or

damaged. Check the blade adapter (5) for

damage. Before you operate the unit, replace

damaged parts with original equipment parts.

See the authorized service center in your area.

Every three years, have an authorized service

person inspect the blade or replace the old

blade with an original equipment part.

How To Remove And Install The Blade

(Figure 14)

1. Remove the mower housing. See the

instructions on “How To Remove The

Mower Housing”.

2. Use a piece of wood to keep the blade from

rotating.

3. Remove the nut (3) that holds the

blade (1).

4. Check the blade (1) and the blade adapter

(5) according to the instructions for “Inspect

Blade”. Replace a badly worn or damaged

blade with an original equipment blade. See

an authorized service centre in your area.

5. Clean the top and bottom of the mower

housing. Remove all the grass and debris.

6. Mount the blade (1) and blade adapter (5)

on the mandrel (6).

7. Mount the blade (1) so that the hi-lift

edges (7) are up. If the blade is upside

down, the blade will not cut correctly and

can cause an accident.

8. Fasten the blade (1) with the original

washers and nut (3). Make sure the outside

rim of the Belleville washer (2) is against

the blade (1).

WARNING: Always keep the nut (3)

tight that holds the blade (1). A loose

nut or blade can cause an accident.

9. Tighten the nut (3) that holds the blade (1)

to a torque of 30 foot pounds (41,5 Nm).

10. Install the mower housing. See “How To

Remove The Mower Housing”.

Not for

Reproduction

How To Check The Blade Rotation

Control

WARNING: To prevent an injury, the

blade rotation control must operate

correctly.

In normal usage, the blade rotation control will

not require an adjustment. However, if the

cutting performance decreases or the quality of

cut is poor, make the following changes.

1. When you mow, make sure the throttle

control is in the FAST position.

2. (Figure 6) Move the blade rotation control

(1) to the DISENGAGE position (8).

3. Stop the engine. Disconnect the wire from

the spark plug.

4. Check the blade(s). Keep a sharp edge on

the blade(s). A blade that is not sharp will

cause the tips of the grass to become

brown.

5. If the quality of cut has not improved,

replace the mower drive belt. See “How To

Replace The Mower Drive Belt”. If the

replacing the belt does not correct the

problem, take the unit to an authorized

service center.

6. Move the blade rotation control (1) to the

DISENGAGE position (8). Stop the engine.

Disconnect the wire from the spark plug.

7. (Figure 15) Check the operation of the

blade brake. Rotate the pulley with your

hand. Make sure that the brake pad (7) is

pressed tightly against the pulley.

WARNING: If the brake pad (7) does not

press tightly against the pulley, take the

unit to an authorized service centre.

8. (Figure 6) Move the blade rotation control

(1) to the ENGAGE position (9).

9. (Figure 15) Check the pads for the blade

brake (7). If the pads are excessively worn

or damaged, replace the brake pad

assemblies. Correct replacement parts and

assistance are available from an authorized

service center.

10. Attach the wire to the spark plug. Mow for a

short distance and again check the

operation of the blade rotation control.

11. When you move the blade rotation control to

the DISENGAGE position, all movement will

stop within five seconds. If there is

movement of the belt or the blades continue

to rotate, engage and disengage the blade

rotation control five times to remove any

excess rubber from a new mower drive belt.

If you need assistance, take the unit to an

authorized service center.

How To Check And Adjust The Clutch

(Figure 16)

If the motion drive belt is loose, the clutch will

slip when; going up a hill, pulling a heavy load,

or the unit will not move forward. Adjust the

clutch as follows.

WARNING: Before you make an in

spection, adjustment, or repair to the

unit, disconnect the wire to the spark

plug. Remove the wire from the spark plug to

prevent the engine from starting by accident.

1. Check the routing of the motion drive belt.

Make sure the belt is installed correctly and

is inside all the belt guides.

2. Remove the cotter pin (1), washer (2), and

brake spring (3) from the adjustable

nut (4).

3. Disconnect the adjustable nut (4) from the

brake lever assembly (5).

4. Align the hole in the brake lever (5) with the

rear of the slot in the frame.

5. Push the clutch rod (6) toward the rear.

Turn the adjustable nut (4) until the nut will

fit through the hole in the brake lever (5).

6. Assemble the adjustable nut (4) to the

brake lever (5) and to the brake spring (3).

Fasten with the washer (2) and cotter

pin (1).

7. If the belt still slips after the clutch has been

adjusted, then the motion drive belt is worn

or damaged and must be replaced. See

“How To Replace The Motion Drive Belt”.

How To Check And Adjust The Drive

Brake (Figure 17)

1. The location of the drive brake is on the left

side of the gear box (see Figure 17).

2. Make sure the parking brake is set and the

automatic drive disconnect is in the PUSH

position (A, Figure 7).

3. Push the unit. If the rear wheels rotate,

adjust the brake pads as follows:

a. Release the parking brake.

b. Remove the brake arm spring (1) and

cotter pin (2) that secures the castle nut

(3).

c. Insert a 0.020 in. feeler gauge between

the brake rotor and top brake puck, then

set the brake by finger tightening or

loosening the castle nut.

d. Install a new cotter pin to secure the

castle nut, and then install the brake arm

spring.

e. Engage the parking brake.

f. Push the unit. If the rear wheels do not

turn, the drive brake is correctly adjusted.

g. Release the parking brake.

NOTE: If you cannot correctly adjust the

drive brake, replace the brake pads. Correct

replacement parts and assistance are

available from an authorized service center.

How To Remove The Battery (Figure 3)

To charge or clean the battery (1), remove the

battery (1) from the unit as follows.

WARNING: To prevent sparks,

disconnect the black battery cable (8)

from the negative (-) terminal before

you disconnect the red cable (5).

WARNING: The battery contains

sulphuric acid which is harmful to the

skin, eyes and clothing. If the acid

gets on the body or clothing, wash with

water.

1. Disconnect the black cable (8) from the

negative (-) terminal.

2. Disconnect the red cable (5) from the

positive (+) terminal (4).

3. To disconnect the battery retainer (2) from

the battery tray (3), push in on the lower

end of the battery retainer (2).

4. Remove the battery (1) from the right side

of the unit.

How To Charge The Battery (Figure 3)

WARNING: When you charge the

battery, do not smoke. Keep the

battery away from any sparks. The

fumes from the battery acid can cause an

explosion.

1. Before you charge the battery (1), remove

the battery (1).

2. To charge the battery (1), use a 12 volt

battery charger. Charge at a rate of 6

amperes for 1 hour.

3. Install the battery (1).

WARNING: To prevent sparks, fasten

the red cable to the positive (+) terminal

before you connect the black cable.

4. Fasten the red cable (5) to the positive (+)

terminal (4) with the fasteners as shown.

5. Fasten the black cable (8) to the negative

(-) terminal with the fasteners as shown.

6. Connect the battery retainer (2) to the

battery tray (3).

How To Level The Mower Housing

If the mower housing is level, the blade will cut

easier and the lawn will look better.

WARNING: Before you make an

inspection, adjustment, or repair to

the unit, disconnect the wire to the

spark plug. Remove the spark plug wire to

prevent the engine from starting by accident.

1. Make sure the unit is on a hard flat surface.

2. Check the air pressure in the tires. If the air

pressure is incorrect, the mower housing

will not cut level. The correct air pressure is

shown on the side of the tire.

3. Open the cover (5).

4. (Figure 18) Move the lift lever (1) to the

LEVEL ADJUSTMENT position (2).

5. (Figure 18 and 19) Loosen the front and

rear adjuster knobs (4). Make sure both

sides of the mower housing are sitting on a

flat surface. Also, make sure the lift links

and adjuster plates are loose and can easily

move up or down.

6. Tighten the front and rear adjuster knobs

(4). Make sure the adjuster knobs (4) are

tight. If necessary, use a wrench to tighten

the adjuster knobs (4). For plastic adjuster

knobs (4), tighten to a torque of 7 foot

pounds (9,5 Nm). For metal adjuster knobs

(4), tighten to a torque of 10 foot pounds

(13,5 Nm).

7. (Figure 20) Raise the lift lever (1) from the

LEVEL ADJUSTMENT position (2) to a

CUTTING HEIGHT position (3).

8. Close the cover (5).

9. Mow for a short distance. If the height of cut

is not level, repeat the above steps.

CAUTION: Do not operate with the mower

housing in the LEVEL ADJUSTMENT

position (2). If you operate in the LEVEL

ADJUSTMENT position (2), the mower

housing and blade will be damaged.

Not for

Reproduction

Where To Lubricate (Figure 21)

Models with grease fittings:

Lubricate with grease gun.

Apply grease with a brush to the

areas shown.

Lubricate the areas shown

with engine oil.

NOTE: Apply grease to the steering gear

assembly.

CAUTION: If the unit is operated in dry areas

that have sand, use a dry graphite spray to

lubricate the unit.

Check the Tires

Check the air pressure in the tires. Tires with too

much air pressure will cause the unit to ride

rough. Also, the wrong air pressure will keep the

mower housing from cutting level. The correct

air pressure is shown on the side of the tire.

How To Replace The Mower Drive Belt

(Figure 15)

1. Remove the mower housing. See the

instructions on “How To Remove The

Mower Housing”.

2. Pull the belt retainer (1) away from the

idler pulley (2) and remove the mower

drive belt (3).

3. Pull the brake pad (7) away from the jack-

shaft pulley (4) and remove the mower

drive belt (3).

NOTE: Replace the mower drive belt (3)

with an original equipment belt from an

authorized service center.

4. A correct replacement part or assistance is

available from an Authorized Service Centre

in your area.

5. To install the motion drive belt, reverse the

above steps.

6. Install the mower housing. See the

instructions on “How To Install The Mower

Housing”.

7. Before you mow, check the blade rotation

control. See the instructions on “How To

Adjust The Blade Rotation Control”.

How To Remove The Mower Housing

1. (Figure 6) Move the blade rotation control

(1) to the DISENGAGE position (8).

2. (Figure 18) Move the lift lever (1) to the

LEVEL ADJUSTMENT position (2).

NOTE: Make sure the lift lever (1) is locked in

the LEVEL ADJUSTMENT position (2).

3. (Figure 24) Remove the hair pins and the

washers from the rear suspension arms

(3). See illustrations “C” and “D”.

4. Remove the hair pins and washers from the

suspension links (4). See illustrations “A”

and “B”.

5. Disconnect the extension spring (5) from the

blade control rod (6). See illustration “E”.

6. Disconnect the front hanger (9) from the

frame support. See illustration “F”.

7. Remove the mower drive belt (7) from the

stack pulley (8). See illustration “G”.

8. Pull the mower housing away from the right

side of the unit.

9. To operate without the mower housing,

move the lift lever to the TOP position.

10. To install the mower housing, reverse the

above steps.

11. Make sure the mower drive belt (7) is

inside all the belt guides (10) and is also

below the spacer tube (11).

How To Install The Wheels

If the wheels must be removed for service,

make sure they are installed as follows:

Front Wheel (Figure 22)

1. Make sure the valve stem (2) is to the

outside. Slide the front wheel (1) onto the

spindle (3).

2. Fasten the front wheel (1) with washers

(4) and cotter pin (5). Bend the ends of the

cotter pin (5) apart to keep the front wheel

(1) on the spindle (3).

3. If your model has hub caps (6), install the

hub caps (6). Make sure the washers (4)

hold the hub caps (6) in place.

Rear Wheel (Figure 23)

1. Install the washers (7) and spacer (8) onto

the axle (9).

2. Mount the square key (10) in the key slot

(11).

3. Make sure the valve stem (2) is to the

outside. Align the slot in the rear wheel (12)

with the square key (10). Slide the rear

wheel (12) on the axle (9).

4. Fasten the rear wheel (12) with washer (7)

and e-ring (13).

5. If your model has hub caps (6), install the

hub caps (6). Make sure the washer (7)

holds the hub caps (6) in place.

How To Replace The Fuse

If the fuse is blown, the engine will not start.

Remove the fuse and replace with a 15 amp.

automotive fuse.

Storage (over 30 days)

At the end of each year, prepare the unit for

storage as follows.

1. Drain the fuel from the carburettor and the

fuel tank. Change the engine oil. See the

engine manufacturer’s instructions.

2. Clean the entire unit.

3. Charge the battery.

How To Order Replacement Parts

The replacement parts are shown either on the

back pages of this Operator’s Manual or in a

separate Illustrated Parts List (IPL).

Use only manufacturer’s authorized or approved

replacement parts. Do not use attachments or

accessories not specifically recommended for

this unit. In order to obtain proper replacement

parts you must supply the model number of your

mower (see nameplate).

Replacement parts, except for the engine,

transmission, transaxle or differential, are

available from the store where the mower was

purchased or a service shop recommended by

the store.

Warranty service is available only through

Authorized Service Dealers. Locate your

nearest dealer in our locator map at

www.murray.com.

Replacement parts for the engine, transaxle, or

transmission, are available from the

manufacturer’s authorized service center found

in the commercial pages of the telephone

directory. Also, see the individual engine or

transmission warranties to order replacement

parts.

When ordering the following information is

required:

(1) The Model Number

(2) Serial Number

(3) Part Number

(4) Quantity

Not for

Reproduction

TROUBLESHOOTING CHART

PROBLEM: The engine will not start.

1. Follow the steps, “How To Start The Engine”

in this book.

2. Electric-Start Models: Clean the battery

terminals. Tighten the cables.

3. Check for a loose wire. Tighten the limit

switches. (See the wiring diagram.)

4. Drain the fuel tank. Clean the fuel line.

Replace the fuel filter.

5. Remove the spark plug(s). Move the throttle

to the SLOW position. Turn the ignition key

to the ON position. Try to start the engine

sev eral times. Install the spark plug.

6. Replace the spark plug.

7. Adjust the carburettor.

PROBLEM: The engine will not turn

over.

1. Follow the steps, “How To Start The Engine”

in this book.

2. Electric-Start Models: Charge the battery.

3. Replace the fuse.

4. Check the wiring harness for damage or a

loose connection. Repair the damaged wire.

5. Electric-Start Models: replace the solenoid.

Recoil-Start Models: replace the module.

PROBLEM: The engine is difficult to

start.

1. Adjust the carburetor.

2. Replace the spark plug.

3. Replace the fuel filter.

PROBLEM: The engine does not run

smooth or has a loss of power.

1. Check the oil.

2. Clean the air filter.

3. Clean the air screen.

4. Replace the spark plug.

5. The engine is working too hard. Use a lower

gear.

6. Adjust the carburetor.

7. Replace the fuel filter.

PROBLEM: The engine does not run

smooth at fast speed.

1. Replace the spark plug.

2. Adjust the throttle control.

3. Clean the air filter.

4. Replace the fuel filter.

PROBLEM: The engine stops when the

blades are engaged.

1. Check the wiring harness for damage or a

loose connection. Repair the damaged wire.

2. Grass bag must be installed (applies only to

model with rear discharge grass bag).

PROBLEM: On slopes, the engine

stops.

1. Mow up and down slopes. Never mow

across a slope.

PROBLEM: The engine will not idle.

1. Replace the spark plug.

2. Clean the air filter.

3. Adjust the carburetor.

4. Adjust the throttle control.

5. Drain the fuel tank. Clean the fuel line.

Replace the fuel filter.

PROBLEM: A hot engine causes a

decrease in power.

1. Clean the air screen.

2. Check the oil.

3. Adjust the carburetor.

4. Replace the fuel filter.

PROBLEM: Excessive vibration.

1. Replace the blade.

2. Check for loose engine bolts.

3. Decrease the air pressure in the tyres.

4. Adjust the carburetor.

5. Check for a damaged belt or damaged

pulley. Replace the damaged parts.

PROBLEM: The grass does not

discharge correctly.

1. Stop the engine. Clean the mower housing.

2. Raise the height of cut.

3. Replace or sharpen the blade(s).

4. Move the shift lever to a slower speed.

5. Move the throttle control to the FAST

position.

6. Replace the spring for the blade idler.

7. Clean the extension tube and the connector

tube (applies only to model with rear

discharge grass bag).

PROBLEM: The mower housing does

not cut level.

1. Check the air pressure in the tyres.

2. Adjust the level of the mower housing.

3. Check the front axle. If the front axle does

not freely pivot, loosen the axle bolt(s).

PROBLEM: The mower blades will not

rotate.

1. Check the mower drive belt. Make sure the

belt is installed correctly.

2. Replace the mower drive belt.

PROBLEM: The unit will not move when

the clutch is engaged.

1. Check the motion drive belt. Make sure the

belt is installed correctly.

2. Adjust the clutch.

3. Replace the motion drive belt.

PROBLEM: The unit moves slower or

stops when the clutch is engaged.

1. Adjust the clutch.

2. Replace the motion drive belt.

PROBLEM: When the clutch/brake

pedal is released, belt noise can be

heard.

1. Temporary belt noise does not change the

operation of the unit. If belt noise is

continuous, check the routing of the belt.

Make sure the belt is inside all belt guides.

2. If the noise is continuous, adjust the clutch.

PROBLEM: The rear wheels spin over

uneven terrain.

1. Check the front axle. If the front axle does

not freely pivot, loosen the axle bolt(s).

Not for

Reproduction

BRIGGS & STRATTON CORPORATION OWNER WARRANTY POLICY

Effective January 1, 2006 replaces all undated Warranties and all Warranties dated before January 1, 2006

Briggs & Stratton Corporation will repair or replace, free of charge, any part(s) of the product that is defective in material or workmanship or both.

Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is effective

for the time periods and subject to the conditions stated below. For warranty service, find the nearest Authorized Service Dealer in your area. For

warranty service, find the nearest Authorized Service Dealer in our dealer locator map at www.murray.com.

THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT PERMITTED BY LAW ANY AND ALL

IMPLIED WARRANTIES ARE EXCLUDED. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE EXCLUDED TO THE

EXTENT EXCLUSION IS PERMITTED BY LAW. Some states or countries do not allow limitations on how long an implied warranty lasts, and

some states or countries do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation and exclusion

may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state or country to

country.

LIMITED WARRANTY

WARRANTY TERMS

Consumer Commercial

esUesUtinU/dnarB

syad09sraey2srotcarT/srediR ..................... ...........

The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of

time stated in the table above. “Consumer use” means personal residential household use by a retail consumer. “Commercial use” means

all other uses, including use for commercial, income producing or rental purposes. Once product has experienced commercial use, it shall

thereafter be considered as commercial use for purposes of this warranty.

No warranty registration is necessary to obtain warranty on Murray branded products. Save your proof of purchase receipt. If you do not

provide proof of the initial purchase date at the time warranty service is requested, the manufacturing date of the product will be used to

determine the warranty.

ABOUT YOUR WARRANTY

We welcome warranty repair and apologize to you for being inconvenienced. Any Authorized Service Dealer may perform warranty

repairs. Most warranty repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. For example,

warranty service would not apply to the product if damage occurred because of misuse, lack of routine maintenance, shipping, handling,

warehousing or improper installation. Similarly, the warranty is void if the serial number on the product has been removed or the product

has been altered or modified.

This warranty covers product related defective material and/or workmanship only. To avoid misunderstanding which might occur be-

tween the customer and the Dealer, listed below are some of the causes of product failure that the warranty does not cover.

Normal Wear: Small Engine Powered Equipment, like all mechanical devices, needs periodic parts and service to perform well. Warranty does not

cover repair when normal use has exhausted the life of the product or part.

Installation: This warranty does not apply to product that has been subjected to improper or unauthorized installation, alteration or modification. Nor

installations that prevent starting, cause unsatisfactory engine performance.

Improper Maintenance: The life of this product depends upon the conditions under which it operates, and the care it receives. Recommended

maintenance and adjustment intervals are stated in the Operator’s Manual. Often product, such as tillers, edgers, rotary mowers, are used in dusty

or dirty conditions, which can cause what appears to be premature wear. Such wear, when caused by dirt, dust, or other abrasive material entering

the product because of improper maintenance is not covered by warranty. The warranty will not cover repairs due to problems caused by replace-

ment parts that are not original manufactured part(s).

Incorrect and/or insufficient fuel or lubrication: This warranty does not cover damage caused by the use of stale fuel, or altered gasolines. Dam-

age to engine or engine components ie, combustion chamber, valves, valve seats, valve guides, burned starter motor windings caused by use of

alternate fuels such as liquified petroleum, natural gas, are not covered unless engine is certified for this operation. Parts which are scored or bro-

ken because product was operated with insufficient, contaminated or incorrect grade of lubricating oil as well as product components damaged due

to lack of lubrication are not covered.

Operational Misuse: Proper operation of the product is stated in the Operator’s Manual. Product damaged by overspeeding, overheating, or opera-

tion in a confined area without sufficient ventilation. Product broken by excessive vibration caused by a loose engine mounting, loose or unbalanced

blades, impellers, overspeeding, or bent crankshaft due to striking of solid object. Damage or malfunctions resulting from accidents, abuse, or im-

proper servicing or freezing or chemical deterioration, as well as operating in excess of recommended capacities as outlined in the Operator’s

Manual are not covered.

Routine tune-up, wear items or adjustments: This warranty excludes wear items such as oil, belts, blades, o-rings, filters, etc.

Other exclusions: Repair or adjustments for part(s) that are not manufactured by Briggs & Stratton Corporation, are not covered, see warranty for

respective manufacturers. This warranty excludes failures due to acts of God and other major forceful events beyond the manufacturers con-

trol. Also excluded are used, reconditioned, and demonstration products.

Warranty service is available only through Authorized Service Dealers. Locate your nearest dealer in our locator map at www.murray.com.

Not for

Reproduction

MEZINÁRODNÍ DIAGRAMY

DŮLEŽITÉ: Následující diagramy se nachází

na vaší jednotce nebo v literatuře dodané

s výrobkem. Před použitím jednotky zjistěte

a porozumějte významu každého diagramu.

POZNÁMKA: Ilustrace a diagramy začínají na

stránce 2.

Diagramy bezpečnostních varování

(Obrázek 25)

1VAROVÁNÍ

2DŮLEŽITÉ: Před použitím tohoto stroje si

přečtěte Manuál majitele.

3VAROVÁNÍ: Odhazované předměty. Osoby

udržujte mimo stroj. Před použitím stroje si

přečtěte Pokyny uživatele.

4VAROVÁNÍ: Tento stroj nepoužívejte na

svazích větších než 10 stupňů.

5NEBEZPEČÍ: Osoby, zvláště děti, udržujte

mimo jednotku.

6NEBEZPEČÍ: Bez schodů.

7NEBEZPEČÍ: Ruce a nohy udržujte mimo

dosah rotujících nožů.

8NEBEZPEČÍ: Před servisem jednotky

odpojte drát svíčky.

9VAROVÁNÍ: Horký povrch.

10 VAROVÁNÍ: Při zapojení či odpojování

doplňků dávejte pozor.

11 VAROVÁNÍ: Zmáčknuté prsty.

12 DŮLEŽITÉ: K vyrovnání plošiny dodržujte

pokynz v Manuálu Majitele.

13 VAROVÁNÍ: Když běží motor, zůstávejte

mimo dosah nožů sekačky.

Diagramy řízení a funkc (Obrázek 26)

1Nastartování motoru

2Světla

3Běh motoru

4Zastavení motoru

5Běh motoru

6Brzda

7Parkovací brzda

8Spojka

9Pomalu

10 Rychle

11 Sytič

12 Olej

13 Ovladač rotace nože

14 Zvednout

15 Palivo

OBSAH

MEZINÁRODNÍ DIAGRAMY 9

INFORMACE VLASTNÍKA 10

POSTUPY PRO BEZPEČNÉ POUŽITÍ 10

MONTÁŽ 11

OVLÁDÁNÍ 12

PLÁN ÚDRŽBY 15

ÚDRŽBA 15

PLÁN ŘEŠENÍ PROBLÉMŮ 18

ONEZEBÁ ZÁRUKA 19

Not for

Reproduction

La pagina sta caricando ...

Simplicity 10.5HP AND 30IN Manuale utente

Marca: Simplicity

Modello: 10.5HP AND 30IN

Categoria: Tosa erba

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

français: Simplicity 10.5HP AND 30IN Manuel utilisateur
Deutsch: Simplicity 10.5HP AND 30IN Benutzerhandbuch
slovenčina: Simplicity 10.5HP AND 30IN Používateľská príručka
dansk: Simplicity 10.5HP AND 30IN Brugermanual
eesti: Simplicity 10.5HP AND 30IN Kasutusjuhend
svenska: Simplicity 10.5HP AND 30IN Användarmanual

Simplicity 10.5HP AND 30IN Manuale utente

Simplicity 10.5HP AND 30IN Manuale utente

in altre lingue

Documenti correlati

Altri documenti