ASROCK 880GMH-LE USB3 Manuale del proprietario

11

1

ASRock 880GMH-LE/USB3 Motherboard

EnglishEnglish

English

Copyright Notice:Copyright Notice:

Copyright Notice:

No part of this installation guide may be reproduced, transcribed, transmitted, or trans-

lated in any language, in any form or by any means, except duplication of documen-

tation by the purchaser for backup purpose, without written consent of ASRock Inc.

Products and corporate names appearing in this guide may or may not be registered

trademarks or copyrights of their respective companies, and are used only for identifica-

tion or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:Disclaimer:

Disclaimer:

Specifications and information contained in this guide are furnished for informational

use only and subject to change without notice, and should not be constructed as a

commitment by ASRock. ASRock assumes no responsibility for any errors or omissions

that may appear in this guide.

With respect to the contents of this guide, ASRock does not provide warranty of any kind,

either expressed or implied, including but not limited to the implied warranties or

conditions of merchantability or fitness for a particular purpose. In no event shall

ASRock, its directors, officers, employees, or agents be liable for any indirect, special,

incidental, or consequential damages (including damages for loss of profits, loss of

business, loss of data, interruption of business and the like), even if ASRock has been

advised of the possibility of such damages arising from any defect or error in the guide

or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

Published June 2010

CALIFORNIA, USA ONLY

The Lithium battery adopted on this motherboard contains Perchlorate, a toxic

substance controlled in Perchlorate Best Management Practices (BMP) regulations

passed by the California Legislature. When you discard the Lithium battery in

California, USA, please follow the related regulations in advance.

“Perchlorate Material-special handling may apply, see

www.dtsc.ca.gov/hazardouswaste/perchlorate”

ASRock Website: http://www.asrock.com

22

2

ASRock 880GMH-LE/USB3 Motherboard

EnglishEnglish

English

Motherboard LayoutMotherboard Layout

Motherboard Layout

1 PS2_USB_PW1 Jumper 19 Seondary SATAII Connector (SATAII_2, Blue)

2 ATX 12V Power Connector (ATX12V1) 20 Primary SATAII Connector (SATAII_1, Blue)

3 CPU Heatsink Retention Module 21 Chassis Fan Connector (CHA_FAN1)

4 AM3 CPU Socket 22 Infrared Module Header (IR1)

5 2 x 240-pin DDR3 DIMM Slots 23 USB_PW3 Jumper

(Dual Channel: DDR3_A1, DDR3_B1; Blue) 24 USB 2.0 Header (USB6_7, Blue)

6 CPU Fan Connector (CPU_FAN1) 25 USB 2.0 Header (USB10_11, Blue)

7 Clear CMOS Jumper (CLRCMOS1) 26 USB 2.0 Header (USB8_9, Blue)

8 ATX Power Connector (ATXPWR1) 27 Print Port Header (LPT1)

9 Power Fan Connector (PWR_FAN1) 28 Floppy Connector (FLOPPY1)

10 Primary IDE Connector (IDE1, Blue) 29 Internal Audio Connector: CD1 (Black)

11 Fifth SATAII Connector (SATAII_5, Blue) 30 Front Panel Audio Header

12 Sixth SATAII Connector (SATAII_6, Blue) (HD_AUDIO1, White)

13 Fourth SATAII Connector (SATAII_4, Blue) 31 Serial Port Connector (COM1)

14 SPI Flash Memory (8Mb) 32 PCI Slots (PCI1-2)

15 Southbridge Controller 33 PCI Express 2.0 x16 Slot (PCIE2; Blue)

16 Chassis Speaker Header 34 PCI Express 2.0 x1 Slot (PCIE1; White)

(SPEAKER 1, White) 35 Northbridge Controller

17 System Panel Header (PANEL1, White) 36 USB_PW2 Jumper

18 Third SATAII Connector (SATAII_3, Blue)

33

3

ASRock 880GMH-LE/USB3 Motherboard

EnglishEnglish

English

I/O PI/O P

I/O P

anelanel

anel

LAN Port

ACT/LINK

LED

SPEED

LED

* There are two LED next to the LAN port. Please refer to the table below for the LAN port LED

indications.

LAN Port LED Indications

Activity/Link LED SPEED LED

Status Description Status Description

Off No Link Off 10Mbps connection

Blinking Data Activity Orange 100Mbps connection

On Link Green 1Gbps connection

1 PS/2 Mouse Port (Green) 8 USB 2.0 Port (USB4)

2 VGA/D-Sub Port 9 USB 3.0 Port (USB5)

* 3 LAN RJ-45 Port 10 USB 2.0 Ports (USB23)

4 Line In (Light Blue) 11 VGA/HDMI Port

* 5 Front Speaker (Lime) 12 VGA/DVI-D Port

6 Microphone (Pink) 13 PS/2 Keyboard Port (Purple)

7 USB 2.0 Ports (USB01)

To enable Multi-Streaming function, you need to connect a front panel audio cable to the front

panel audio header. After restarting your computer, you will find “VIA HD Audio Deck” tool on

your system. Please follow below instructions according to the OS you install.

For Windows

®

XP / XP 64-bit OS:

Please click “VIA HD Audio Deck” icon , and click “Speaker”. Then you are allowed to

select “2 Channel” or “4 Channel”. Click “Power” to save your change.

For Windows

®

7 / 7 64-bit / Vista

TM

/ Vista

TM

64-bit OS:

Please click “VIA HD Audio Deck” icon , and click “Advanced Options” on the left side

on the bottom. In “Advanced Options” screen, select “Independent Headphone”, and click

“OK” to save your change.

44

4

ASRock 880GMH-LE/USB3 Motherboard

1.1.

1.

IntroductionIntroduction

Introduction

Thank you for purchasing ASRock 880GMH-LE/USB3 motherboard, a reliable

motherboard produced under ASRock’s consistently stringent quality control. It de-

livers excellent performance with robust design conforming to ASRock’s commit-

ment to quality and endurance.

In this manual, chapter 1 and 2 contain introduction of the motherboard and step-by-step

guide to the hardware installation. Chapter 3 and 4 contain the configuration guide to

BIOS setup and information of the Support CD.

Because the motherboard specifications and the BIOS software might

be updated, the content of this manual will be subject to change without

notice. In case any modifications of this manual occur, the updated

version will be available on ASRock website without further notice. You

may find the latest VGA cards and CPU support lists on ASRock website

as well. ASRock website http://www.asrock.com

If you require technical support related to this motherboard, please visit

our website for specific information about the model you are using.

www.asrock.com/support/index.asp

1.11.1

1.1

Package ContentsPackage Contents

Package Contents

ASRock 880GMH-LE/USB3 Motherboard

(Micro ATX Form Factor: 9.6-in x 8.2-in, 24.4 cm x 20.8 cm)

ASRock 880GMH-LE/USB3 Quick Installation Guide

ASRock 880GMH-LE/USB3 Support CD

2 x Serial ATA (SATA) Data Cables (Optional)

1 x I/O Panel Shield

EnglishEnglish

English

55

5

ASRock 880GMH-LE/USB3 Motherboard

EnglishEnglish

English

1.21.2

1.2

SpecificationsSpecifications

Specifications

Platform - Micro ATX Form Factor: 9.6-in x 8.2-in, 24.4 cm x 20.8 cm

- All Solid Capacitor design (100% Japan-made high-quality

Polymer Capacitors)

CPU - Support for Socket AM3 processors: AMD Phenom

TM

II X6 /

X4 / X3 / X2 (except 920 / 940) / Athlon II X4 / X3 / X2 /

Sempron processors

- Six-Core CPU Ready

- Supports ASRock UCC - Unlock CPU Core

- Supports AMD’s Cool ‘n’ Quiet

TM

Technology

- FSB 2600 MHz (5.2 GT/s)

- Supports Untied Overclocking Technology (see CAUTION 1)

- Supports Hyper-Transport 3.0 (HT 3.0) Technology

Chipset - Northbridge: AMD 880G

- Southbridge: AMD SB710

Memory - Dual Channel DDR3 Memory Technology (see CAUTION 2)

- 2 x DDR3 DIMM slots

- Support DDR3 1800(OC)/1600(OC)/1333/1066/800 non-ECC,

un-buffered memory (see CAUTION 3)

- Max. capacity of system memory: 8GB (see CAUTION 4)

Expansion Slot - 1 x PCI Express 2.0 x16 slot (blue @ x16 mode)

- 1 x PCI Express 2.0 x1 slot

- 2 x PCI slots

- Supports ATI

TM

Hybrid CrossFireX

TM

Graphics - Integrated AMD Radeon HD 4250 graphics

- DX10.1 class iGPU, Shader Model 4.1

- Max. shared memory 512MB (see CAUTION 5)

- Three VGA Output options: D-Sub, DVI-D and HDMI

- Supports HDMI Technology with max. resolution up to

1920x1200 (1080P)

- Supports Dual-link DVI with max. resolution up to 2560x1600

@ 75Hz

- Supports D-Sub with max. resolution up to 2048x1536

@ 85Hz

- Supports HDCP function with DVI and HDMI ports

- Supports Full HD 1080p Blu-ray (BD) / HD-DVD playback

with DVI and HDMI ports

Audio - 5.1 CH HD Audio (VIA

®

VT1705 Audio Codec)

66

6

ASRock 880GMH-LE/USB3 Motherboard

EnglishEnglish

English

LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111E

- Supports Wake-On-LAN

- Supports LAN Cable Detection

Rear Panel I/O I/O Panel

- 1 x PS/2 Mouse Port

- 1 x PS/2 Keyboard Port

- 1 x VGA/D-Sub Port

- 1 x VGA/DVI-D Port

- 1 x HDMI Port

- 5 x Ready-to-Use USB 2.0 Ports

- 1 x Ready-to-Use USB 3.0 Port

- 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED LED)

- HD Audio Jack: Front Speaker/Microphone

USB 3.0 - 1 x USB 3.0 port by Fresco FL1000G, supports USB 3.0 up to

5Gb/s

Connector - 6 x Serial ATAII 3.0Gb/s connectors, support RAID (RAID 0,

RAID 1, RAID 10 and JBOD), NCQ, AHCI and “Hot Plug”

functions (see CAUTION 6)

- 1 x ATA133 IDE connector (supports 2 x IDE devices)

- 1 x Floppy connector

- 1 x IR header

- 1 x Print port header

- 1 x COM port header

- CPU/Chassis/Power FAN connector

- 24 pin ATX power connector

- 4 pin 12V power connector

- CD in header

- Front panel audio connector

- 3 x USB 2.0 headers (support 6 USB 2.0 ports)

BIOS Feature - 8Mb AMI BIOS

- AMI Legal BIOS

- Supports “Plug and Play”

- ACPI 1.1 Compliance Wake Up Events

- Supports jumperfree

- SMBIOS 2.3.1 Support

- VCCM, NB Voltage Multi-adjustment

Support CD - Drivers, Utilities, AntiVirus Software (Trial Version), AMD

OverDrive

TM

Utility, AMD Live! Explorer, AMD Fusion, ASRock

Software Suite (CyberLink DVD Suite - OEM and Trial;

Creative Sound Blaster X-Fi MB - Trial)

77

7

ASRock 880GMH-LE/USB3 Motherboard

EnglishEnglish

English

Unique Feature - ASRock OC Tuner (see CAUTION 7)

- Intelligent Energy Saver (see CAUTION 8)

- Instant Boot

- ASRock Instant Flash (see CAUTION 9)

- ASRock OC DNA (see CAUTION 10)

- Hybrid Booster:

- CPU Frequency Stepless Control (see CAUTION 11)

- ASRock U-COP (see CAUTION 12)

- Boot Failure Guard (B.F.G.)

Hardware - CPU Temperature Sensing

Monitor - Chassis Temperature Sensing

- CPU/Chassis/Power Fan Tachometer

- CPU Quiet Fan

- Voltage Monitoring: +12V, +5V, +3.3V, Vcore

OS - Microsoft

®

Windows

®

7 / 7 64-bit / Vista

TM

/ Vista

TM

64-bit

/ XP / XP Media Center / XP 64-bit compliant

Certifications - FCC, CE, WHQL

- ErP/EuP Ready (ErP/EuP ready power supply is required)

(see CAUTION 13)

* For detailed product information, please visit our website: http://www.asrock.com

WARNING

Please realize that there is a certain risk involved with overclocking, including adjusting

the setting in the BIOS, applying Untied Overclocking Technology, or using the third-

party overclocking tools. Overclocking may affect your system stability, or even

cause damage to the components and devices of your system. It should be done at

your own risk and expense. We are not responsible for possible damage caused by

overclocking.

88

8

ASRock 880GMH-LE/USB3 Motherboard

EnglishEnglish

English

CAUTION!

1. This motherboard supports Untied Overclocking Technology. Please read “Un-

tied Overclocking Technology” on page 25 for details.

2. This motherboard supports Dual Channel Memory Technology. Before you

implement Dual Channel Memory Technology, make sure to read the

installation guide of memory modules on page 12 for proper installation.

3. Whether 1800/1600MHz memory speed is supported depends on the AM3

CPU you adopt. If you want to adopt DDR3 1800/1600 memory module

on this motherboard, please refer to the memory support list on our

website for the compatible memory modules.

ASRock website http://www.asrock.com

4. Due to the operating system limitation, the actual memory size may be

less than 4GB for the reservation for system usage under Windows

®

7 /

Vista

TM

/ XP. For Windows

®

OS with 64-bit CPU, there is no such limitation.

5. The maximum shared memory size is defined by the chipset vendor and

is subject to change. Please check AMD website for the latest information.

6. Before installing SATAII hard disk to SATAII connector, please read the “SATAII

Hard Disk Setup Guide” on page 27 of “User Manual” in the support CD to

adjust your SATAII hard disk drive to SATAII mode. You can also connect SATA

hard disk to SATAII connector directly.

7. It is a user-friendly ASRock overclocking tool which allows you to surveil

your system by hardware monitor function and overclock your hardware

devices to get the best system performance under Windows

®

environment.

Please visit our website for the operation procedures of ASRock OC

Tuner. ASRock website: http://www.asrock.com

8. Featuring an advanced proprietary hardware and software design,

Intelligent Energy Saver is a revolutionary technology that delivers

unparalleled power savings. The voltage regulator can reduce the

number of output phases to improve efficiency when the CPU cores are

idle. In other words, it is able to provide exceptional power saving and

improve power efficiency without sacrificing computing performance. To

use Intelligent Energy Saver function, please enable Cool ‘n’ Quiet option

in the BIOS setup in advance. Please visit our website for the operation

procedures of Intelligent Energy Saver.

ASRock website: http://www.asrock.com

9. ASRock Instant Flash is a BIOS flash utility embedded in Flash ROM.

This convenient BIOS update tool allows you to update system BIOS

without entering operating systems first like MS-DOS or Windows

®

. With

this utility, you can press <F6> key during the POST or press <F2> key to

BIOS setup menu to access ASRock Instant Flash. Just launch this tool

and save the new BIOS file to your USB flash drive, floppy disk or hard

drive, then you can update your BIOS only in a few clicks without prepar-

ing an additional floppy diskette or other complicated flash utility. Please

be noted that the USB flash drive or hard drive must use FAT32/16/12 file

system.

99

9

ASRock 880GMH-LE/USB3 Motherboard

EnglishEnglish

English

10. The software name itself – OC DNA literally tells you what it is capable of.

OC DNA, an exclusive utility developed by ASRock, provides a conve-

nient way for the user to record the OC settings and share with others. It

helps you to save your overclocking record under the operating system

and simplifies the complicated recording process of overclocking settings.

With OC DNA, you can save your OC settings as a profile and share with

your friends! Your friends then can load the OC profile to their own system

to get the same OC settings as yours! Please be noticed that the OC

profile can only be shared and worked on the same motherboard.

11. Although this motherboard offers stepless control, it is not recommended

to perform over-clocking. Frequencies other than the recommended CPU

bus frequencies may cause the instability of the system or damage the

CPU.

12. While CPU overheat is detected, the system will automatically shutdown.

Before you resume the system, please check if the CPU fan on the

motherboard functions properly and unplug the power cord, then plug it

back again. To improve heat dissipation, remember to spray thermal

grease between the CPU and the heatsink when you install the PC system.

13. EuP, stands for Energy Using Product, was a provision regulated by

European Union to define the power consumption for the completed system.

According to EuP, the total AC power of the completed system shall be

under 1.00W in off mode condition. To meet EuP standard, an EuP ready

motherboard and an EuP ready power supply are required. According to

Intel’s suggestion, the EuP ready power supply must meet the standard of

5v standby power efficiency is higher than 50% under 100 mA current

consumption. For EuP ready power supply selection, we recommend you

checking with the power supply manufacturer for more details.

1010

10

ASRock 880GMH-LE/USB3 Motherboard

EnglishEnglish

English

2.2.

2.

InstallationInstallation

Installation

This is a Micro ATX form factor (9.6-in x 8.2-in, 24.4 cm x 20.8 cm) motherboard.

Before you install the motherboard, study the configuration of your chassis to en-

sure that the motherboard fits into it.

Pre-installation PrecautionsPre-installation Precautions

Pre-installation Precautions

Take note of the following precautions before you install motherboard

components or change any motherboard settings.

Before you install or remove any component, ensure that the

power is switched off or the power cord is detached from the

power supply. Failure to do so may cause severe damage to the

motherboard, peripherals, and/or components.

1. Unplug the power cord from the wall socket before touching any

component.

2. To avoid damaging the motherboard components due to static

electricity, NEVER place your motherboard directly on the carpet or

the like. Also remember to use a grounded wrist strap or touch a

safety grounded object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded anti-

static pad or in the bag that comes with the component.

5. When placing screws into the screw holes to secure the motherboard

to the chassis, please do not over-tighten the screws! Doing so may

damage the motherboard.

1111

11

ASRock 880GMH-LE/USB3 Motherboard

2.12.1

2.1

CPU InstallationCPU Installation

CPU Installation

Step 1. Unlock the socket by lifting the lever up to a 90

o

angle.

Step 2. Position the CPU directly above the socket such that the CPU corner with

the golden triangle matches the socket corner with a small triangle.

Step 3. Carefully insert the CPU into the socket until it fits in place.

The CPU fits only in one correct orientation. DO NOT force the CPU

into the socket to avoid bending of the pins.

Step 4. When the CPU is in place, press it firmly on the socket while you push

down the socket lever to secure the CPU. The lever clicks on the side tab

to indicate that it is locked.

2.22.2

2.2

Installation of CPU Fan and HeatsinkInstallation of CPU Fan and Heatsink

Installation of CPU Fan and Heatsink

After you install the CPU into this motherboard, it is necessary to install a

larger heatsink and cooling fan to dissipate heat. You also need to spray

thermal grease between the CPU and the heatsink to improve heat

dissipation. Make sure that the CPU and the heatsink are securely fas-

tened and in good contact with each other. Then connect the CPU fan to

the CPU FAN connector (CPU_FAN1, see Page 2, No. 6). For proper

installation, please kindly refer to the instruction manuals of the CPU fan

and the heatsink.

STEP 1:

Lift Up The Socket Lever

STEP 2 / STEP 3:

Match The CPU Golden Triangle

To The Socket Corner Small

Triangle

STEP 4:

Push Down And Lock

The Socket Lever

Lever 90° Up

CPU Golden Triangle

Socker Corner Small Triangle

EnglishEnglish

English

1212

12

ASRock 880GMH-LE/USB3 Motherboard

EnglishEnglish

English

2.3 Installation of Memory Modules (DIMM)2.3 Installation of Memory Modules (DIMM)

2.3 Installation of Memory Modules (DIMM)

880GMH-LE/USB3 motherboard provides two 240-pin DDR3 (Double Data Rate 3)

DIMM slots, and supports Dual Channel Memory Technology. For dual channel

configuration, you always need to install two identical (the same brand, speed,

size and chip-type) memory modules in the DDR3 DIMM slots to activate Dual Channel

Memory Technology. Otherwise, it will operate at single channel mode.

1. It is not allowed to install a DDR or DDR2 memory module into

DDR3 slot;otherwise, this motherboard and DIMM may be damaged.

2. If you install only one memory module or two non-identical memory

modules, it is unable to activate the Dual Channel Memory Technology.

Installing a DIMMInstalling a DIMM

Installing a DIMM

Please make sure to disconnect power supply before adding or

removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.

Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break

on the slot.

The DIMM only fits in one correct orientation. It will cause permanent

damage to the motherboard and the DIMM if you force the DIMM into the

slot at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully

snap back in place and the DIMM is properly seated.

1313

13

ASRock 880GMH-LE/USB3 Motherboard

EnglishEnglish

English

2.4 Expansion Slots (PCI and PCI Express Slots)2.4 Expansion Slots (PCI and PCI Express Slots)

2.4 Expansion Slots (PCI and PCI Express Slots)

There are 2 PCI slots and 2 PCI Express slots on this motherboard.

PCI Slots: PCI slots are used to install expansion cards that have the 32-bit PCI

interface.

PCIE Slots:

PCIE1 (PCIE x1 slot; White) is used for PCI Express cards with x1 lane

width cards, such as Gigabit LAN card and SATA2 card.

PCIE2 (PCIE x16 slot; Blue) is used for PCI Express x16 lane width

graphics cards.

Installing an expansion cardInstalling an expansion card

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power

supply is switched off or the power cord is unplugged. Please read the

documentation of the expansion card and make necessary hardware

settings for the card before you start the installation.

Step 2. Remove the system unit cover (if your motherboard is already installed in

a chassis).

Step 3. Remove the bracket facing the slot that you intend to use. Keep the

screws for later use.

Step 4. Align the card connector with the slot and press firmly until the card is

completely seated on the slot.

Step 5. Fasten the card to the chassis with screws.

Step 6. Replace the system cover.

1414

14

ASRock 880GMH-LE/USB3 Motherboard

EnglishEnglish

English

2. If you have installed onboard VGA driver from our support CD to your system

already, you can freely enjoy the benefits of dual monitor function after your

system boots. If you haven’t installed onboard VGA driver yet, please install

onboard VGA driver from our support CD to your system and restart your

computer. Then you can start to use dual monitor function on this motherboard.

1. DVI-D and HDMI ports cannot function at the same time. When one of

them is enabled, the other one will be disabled.

2. When you playback HDCP-protected video from Blu-ray (BD) or

HD-DVD disc, the content will be displayed only in one of the two

monitors instead of both monitors.

2.5 Dual Monitor and Surround Display Features2.5 Dual Monitor and Surround Display Features

2.5 Dual Monitor and Surround Display Features

Dual Monitor Feature

This motherboard supports dual monitor feature. With the internal VGA output

support (DVI-D, D-Sub and HDMI), you can easily enjoy the benefits of dual monitor

feature without installing any add-on VGA card to this motherboard. This

motherboard also provides independent display controllers for DVI-D, D-Sub and

HDMI to support dual VGA output so that DVI-D, D-sub and HDMI can drive same or

different display contents.

To enable dual monitor feature, please follow the below steps:

1. Connect DVI-D monitor cable to VGA/DVI-D port on the I/O panel, connect D-Sub

monitor cable to VGA/D-Sub port on the I/O panel, or connect HDMI monitor

cable to HDMI port on the I/O panel.

VGA/DVI-D port

HDMI port

VGA/D-Sub port

1515

15

ASRock 880GMH-LE/USB3 Motherboard

Surround Display Feature

This motherboard supports surround display upgrade. With the internal VGA

output support (DVI-D, D-Sub and HDMI) and external add-on PCI Express VGA

cards, you can easily enjoy the benefits of surround display feature.

Please refer to the following steps to set up a surround display environment:

1. Install the ATI

TM

PCI Express VGA card on PCIE2 slot. Please refer to page 13 for

proper expansion card installation procedures for details.

2. Connect DVI-D monitor cable to VGA/DVI-D port on the I/O panel, connect D-Sub

monitor cable to VGA/D-Sub port on the I/O panel, or connect HDMI monitor

cable to HDMI port on the I/O panel. Then connect other monitor cables to the

corresponding connectors of the add-on PCI Express VGA card on PCIE2 slot.

3. Boot your system. Press <F2> to enter BIOS setup. Enter “Share Memory”

option to adjust the memory capability to [32MB], [64MB], [128MB] [256MB] or

[512MB] to enable the function of VGA/D-sub. Please make sure that the value

you select is less than the total capability of the system memory. If you do not

adjust the BIOS setup, the default value of “Share Memory”, [Auto], will disable

VGA/D-Sub function when the add-on VGA card is inserted to this

motherboard.

4. Install the onboard VGA driver and the add-on PCI Express VGA card driver to

your system. If you have installed the drivers already, there is no need to install

them again.

5. Set up a multi-monitor display.

For Windows

®

XP / XP 64-bit OS:

Right click the desktop, choose “Properties”, and select the “Settings” tab

so that you can adjust the parameters of the multi-monitor according to the

steps below.

A. Click the “Identify” button to display a large number on each monitor.

B. Right-click the display icon in the Display Properties dialog that you wish

to be your primary monitor, and then select “Primary”. When you use

multiple monitors with your card, one monitor will always be Primary,

and all additional monitors will be designated as Secondary.

C. Select the display icon identified by the number 2.

D. Click “Extend my Windows desktop onto this monitor”.

E. Right-click the display icon and select “Attached”, if necessary.

F. Set the “Screen Resolution” and “Color Quality” as appropriate for the

second monitor. Click “Apply” or “OK” to apply these new values.

G. Repeat steps C through E for the diaplay icon identified by the number

one, two, three and four.

EnglishEnglish

English

1616

16

ASRock 880GMH-LE/USB3 Motherboard

EnglishEnglish

English

HDCP Function

HDCP function is supported on this motherboard. To use HDCP

function with this motherboard, you need to adopt the monitor that

supports HDCP function as well. Therefore, you can enjoy the

superior display quality with high-definition HDCP encryption

contents. Please refer to below instruction for more details about

HDCP function.

What is HDCP?

HDCP stands for High-Bandwidth Digital Content Protection, a

specification developed by Intel

®

for protecting digital entertainment

content that uses the DVI interface. HDCP is a copy protection

scheme to eliminate the possibility of intercepting digital data

midstream between the video source, or transmitter - such as a

computer, DVD player or set-top box - and the digital display, or

receiver - such as a monitor, television or projector. In other words,

HDCP specification is designed to protect the integrity of content as it

is being transmitted.

Products compatible with the HDCP scheme such as DVD players,

satellite and cable HDTV set-top-boxes, as well as few entertain-

ment PCs requires a secure connection to a compliant display. Due

to the increase in manufacturers employing HDCP in their equipment,

it is highly recommended that the HDTV or LCD monitor you purchase

is compatible.

For Windows

®

7 / 7 64-bit / Vista

TM

/ Vista

TM

64-bit OS:

Right click the desktop, choose “Personalize”, and select the “Display

Settings” tab so that you can adjust the parameters of the multi-monitor

according to the steps below.

A. Click the number ”2” icon.

B. Click the items “This is my main monitor” and “Extend the desktop onto

this monitor”.

C. Click “OK” to save your change.

D. Repeat steps A through C for the display icon identified by the number

three and four.

6. Use Surround Display. Click and drag the display icons to positions representing

the physical setup of your monitors that you would like to use. The placement

of display icons determines how you move items from one monitor to another.

1717

17

ASRock 880GMH-LE/USB3 Motherboard

ATI Catalyst Control Center

2.62.6

2.6

AA

A

TITI

TI

TMTM

TM

Hybrid CrossF Hybrid CrossF

Hybrid CrossF

ireXireX

ireX

TMTM

TM

Operation Guide Operation Guide

Operation Guide

This motherboard supports ATI

TM

Hybrid CrossFireX

TM

feature. ATI

TM

Hybrid

CrossFireX

TM

brings multi-GPU performance capabilities by enabling an AMD 880G

integrated graphics processor and a discrete graphics processor to operate

simultaneously with combined output to a single display for blisteringly-fast frame

rates. Currently, ATI

TM

Hybrid CrossFireX

TM

Technology is only supported with

Windows

®

Vista

TM

/ 7 OS, and is not available with Windows

®

XP OS. In the future,

ATI

TM

Hybrid CrossFireX

TM

may be supported with Windows

®

XP OS. Please visit

our website for updated information.

Enjoy the benefit of AEnjoy the benefit of A

Enjoy the benefit of A

TITI

TI

TMTM

TM

Hybrid CrossF Hybrid CrossF

Hybrid CrossF

ireXireX

ireX

TMTM

TM

Step 1. Install one compatible PCI Express graphics card to PCIE2 slot (blue). For

the proper installation procedures, please refer to section “Expansion Slots”.

Step 2. Connect the monitor cable to the correspondent connector on the PCI

Express graphics card on PCIE2 slot.

Step 3. Boot your system. Press <F2> to enter BIOS setup. Enter “Advanced”

screen, and enter “Chipset Settings”. Then set the option “Surround View”

to [Enabled].

Step 4. Boot into OS. Please remove the ATI

TM

driver if you have any VGA driver

installed in your system.

Step 5. Install the onboard VGA driver from our support CD to your system for both

the onboard VGA and the discrete graphics card.

Step 6. Restart your computer. Then you will find “ATI Catalyst Control Center” on

your Windows

®

taskbar.

EnglishEnglish

English

Vendor Chipset Model Driver

ATI RADEON HD5450 ATI Radeon HD 5450 1GB Support CD 8.71

What does an ATI

TM

Hybrid CrossFireX

TM

system include?

An ATI

TM

Hybrid CrossFireX

TM

system includes an ATI

TM

Radeon

TM

5450 series graphics

processor and a motherboard based on an AMD 880G integrated chipset, all operating

in a Windows

®

Vista

TM

/ 7 environment. Please refer to below PCI Express graphics

card support list for ATI

TM

Hybrid CrossFireX

TM

. For the future update of more

compatible PCI Express graphics cards, please visit our website for further

information.

1818

18

ASRock 880GMH-LE/USB3 Motherboard

EnglishEnglish

English

* Hybrid CrossFireX

TM

appearing here is a registered trademark of ATI

TM

Technologies Inc.,

and is used only for identification or explanation and to the owners’ benefit, without intent to

infringe.

* For further information of ATI

TM

Hybrid CrossFireX

TM

technology, please check AMD website

for up dates and details.

Step 7. Double-click “ATI Catalyst Control Center”. Click “View”, click “CrossFire

TM

”,

and then select the option “Enable CrossFire

TM

”.

View

CrossFire

TM

Enable CrossFire

TM

Step 8. Click “Yes” to continue.

Step 9. Click “OK” to save your change.

Step 10. Reboot your system. Then you can freely enjoy the benefit of Hybrid

TM

CrossFireX

TM

feature.

1919

19

ASRock 880GMH-LE/USB3 Motherboard

OpenShort

Clear CMOSDefault

EnglishEnglish

English

2.72.7

2.7

Jumpers SetupJumpers Setup

Jumpers Setup

The illustration shows how jumpers are

setup. When the jumper cap is placed on

pins, the jumper is “Short”. If no jumper cap

is placed on pins, the jumper is “Open”. The

illustration shows a 3-pin jumper whose pin1

and pin2 are “Short” when jumper cap is

placed on these 2 pins.

Jumper Setting

PS2_USB_PW1 Short pin2, pin3 to enable

(see p.2, No. 1) +5VSB (standby) for PS/2 or

USB23 wake up events.

Note: To select +5VSB, it requires 2 Amp and higher standby current provided by

power supply.

USB_PW2 Short pin2, pin3 to enable

(see p.2, No. 36) +5V_DUAL for USB01/45

wake up events.

Note: To select +5V_DUAL, it requires 2 Amp and higher standby current provided

by power supply. When you select +5V_DUAL, USB devices can wake up

the system under S3 (Suspend to RAM) state. To support ErP/EuP

requirement, please set this jumper to +5V.

USB_PW3 Short pin2, pin3 to enable

(see p.2, No. 23) +5VSB (standby) for

USB6_7/8_9/10_11 wake up

events.

Note: To select +5VSB, it requires 2 Amp and higher standby current provided by

power supply.

Clear CMOS Jumper

(CLRCMOS1)

(see p.2, No. 7)

Note: CLRCMOS1 allows you to clear the data in CMOS. The data in CMOS includes

system setup information such as system password, date, time, and system

setup parameters. To clear and reset the system parameters to default setup,

please turn off the computer and unplug the power cord from the power

supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3

on CLRCMOS1 for 5 seconds. However, please do not clear the CMOS right

after you update the BIOS. If you need to clear the CMOS when you just finish

updating the BIOS, you must boot up the system first, and then shut it down

before you do the clear-CMOS action.

2020

20

ASRock 880GMH-LE/USB3 Motherboard

EnglishEnglish

English

the red-striped side to Pin1

2.8 Onboard Headers and Connectors2.8 Onboard Headers and Connectors

2.8 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place

jumper caps over these headers and connectors. Placing jumper caps

over the headers and connectors will cause permanent damage of the

motherboard!

•

Floppy Connector

(33-pin FLOPPY1)

(see p.2 No. 28)

Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the

connector.

Primary IDE connector (Blue)

(39-pin IDE1, see p.2 No. 10)

Note: Please refer to the instruction of your IDE device vendor for the details.

Serial ATAII Connectors These six Serial ATAII (SATAII)

(SATAII_1: see p.2, No. 20) connectors support SATAII

(SATAII_2: see p.2, No. 19) or SATA hard disk for internal

(SATAII_3: see p.2, No. 18) storage devices. The current

(SATAII_4: see p.2, No. 13) SATAII interface allows up to

(SATAII_5: see p.2, No. 11) 3.0 Gb/s data transfer rate.

(SATAII_6: see p.2, No. 12)

Serial ATA (SATA) Either end of the SATA data cable

Data Cable can be connected to the SATA /

(Optional) SATAII hard disk or the SATAII

connector on the motherboard.

connect the black end

to the IDE devices

connect the blue end

to the motherboard

80-conductor ATA 66/100/133 cable

SATAII_1 SATAII_2 SATAII_3

SATAII_4 SATAII_5 SATAII_6

La pagina sta caricando ...

ASROCK 880GMH-LE USB3 Manuale del proprietario

Questo manuale è adatto anche per

ASROCK 880GMH-LE USB3 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti