Hitachi DH 40MR Handling Instructions Manual
- Categoria
- Utensili elettrici
- Tipo
- Handling Instructions Manual
DH 40MR
Rotary Hammer
Bohrhammer
Perforateur percussion
Martello perforatore
Boorhamer
Martillo perforador
Martelo perfurador
Συρδραπαν περιςτρικ
1
Read through carefully and understand these instructions before use.
Diese Anleitung vor Benutzung des Werkzeugs sorgfältig durchlesen und verstehen.
Lire soigneusement et bien assimiler ces instructions avant usage.
Prima dell’uso leggere attentamente e comprendere queste istruzioni.
Deze gebruiksaanwijzing s.v.p. voor gebruik zorgvuldig doorlezen.
Leer cuidadosamente y comprender estas instrucciones antes del uso.
Antes de usar, leia com cuidado para assimilar estas instruções.
∆ιαάστε πρσεκτικά και κατανήσετε αυτές τις δηγίες πριν τη ρήση.
208
Code No. C99118371 N
Printed in Japan
Handling instructions
Bedienungsanleitung
Mode d’emploi
Istruzioni per l’uso
Gebruiksaanwijzing
Instrucciones de manejo
Instruções de uso
δηγίες ειρισµύ
3
6
9
12
2
5
8
11
1
2
1
4
7
10
Hitachi Power Tools Europe GmbH
Siemensring 34, 47877 Willich, F. R. Germany
Hitachi Koki Co., Ltd.
Shinagawa Intercity Tower A, 15-1, Konan 2-chome,
Minato-ku, Tokyo, Japan
Nederlands
EC VERKLARING VAN CONFORMITEIT
Wij verklaren onder eigen verantwoordelijkheid dat dit
produkt conform de richtlijnen of gestandardiseerde
documenten EN50144, HD400, EN55014-1, EN55014-2,
EN61000-3-2, EN61000-3-3 en/of EN61000-3-11 voldoet
aan de eisen van EEG Bepalingen 73/23/EEG, 89/336/
EEG en/of 98/37/EC.
Deze verklaring is van toepassing op produkten
voorzien van de CE-markeringen.
Español
DECLARACIÓN DE CONFORMIDAD DE LA CE
Declaramos bajo nuestra única responsabilidad que
este producto está de acuerdo con las normas o con
los documentos de normalización EN50144, HD400,
EN55014-1, EN55014-2, EN61000-3-2, EN61000-3-3 y/o
EN61000-3-11, según indican las Directrices del Consejo
73/23/CEE, 89/336/CEE y/o 98/37/CE.
Esta declaración se aplica a los productos con marcas
de la CE.
Portugûes
DECLARAÇÃO DE CONFORMIDADE CE
Declaramos, sob nossa única e inteira responsabilidade,
que este produto está de acordo com as normas ou
documentos normativos EN50144, HD400, EN55014-1,
EN55014-2, EN61000-3-2, EN61000-3-3 e/ou EN61000-
3-11, em conformidade com as Diretrizes 73/23/CEE,
89/336/CEE e/ou 98/37/CE do Conselho.
Esta declaração se aplica aos produtos designados CE.
Ελληνικά
EK ∆ΗΛ·ΣΗ ΕΝΑΡΜΝΙΣΜΥ
∆ηλώνυµε µε απλυτη υπευθυντητα τι αυτ τ
πριν είναι εναρµνισµέν µε τα πρτυπα ή τα
έγραα πρτύπων EN50144, HD400, EN55014-1,
EN55014-2, EN61000-3-2, EN61000-3-3 και / ή EN61000-
3-11 σε συµωνία µε τις δηγίες τυ Συµυλίυ 73/
23/EOK, 89/336/EOK και/ή 98/37/EK.
Αυτή η δήλωση ισύει στ πριν µε τ σηµάδι CE.
English
EC DECLARATION OF CONFORMITY
We declare under our sole responsibility that this
product is in conformity with standards or standardized
documents EN50144, HD400, EN55014-1, EN55014-2,
EN61000-3-2, EN61000-3-3 and/or EN61000-3-11 in
accordance with Council Directives 73/23/EEC, 89/336/
EEC and/or 98/37/EC.
This declaration is applicable to the product affixed CE
marking.
Deutsch
ERKLÄRUNG ZUR KONFORMITÄT MIT CE-REGELN
Wir erklären mit alleiniger Verantwortung, daß dieses
Produkt den Standards oder standardisierten
Dokumenten EN50144, HD400, EN55014-1, EN55014-2,
EN61000-3-2, EN61000-3-3 und/oder EN61000-3-11 in
Übereinstimmung mit den Direktiven des Europarats
73/23/EWG, 89/336/EWG und/order 98/37/CE entspricht.
Diese Erklärung gilt für Produkte, die die CE-Markierung
tragen.
Français
DECLARATION DE CONFORMITE CE
Nous déclarons sous notre seule et entière respon-
sabilité que ce produit est conforme aux normes ou
documents normalisés EN50144, HD400, EN55014-1,
EN55014-2, EN61000-3-2, EN61000-3-3 et/ou EN61000-
3-11 en accord avec les Directives 73/23/CEE, 89/336/
CEE et/ou 98/37/CE du Conseil.
Cette déclaration s’applique aux produits désignés CE.
Italiano
DICHIARAZIONE DI CONFORMITÀ CE
Si dichiara sotto nostra responsabilità che questo
prodotto è conforme agli standard o ai documenti
standardizzati EN50144, HD400, EN55014-1, EN55014-
2, EN61000-3-2, EN61000-3-3 e/o EN61000-3-11
conforme alle direttive 73/23/CEE, 89/336/CEE e/o 98/
37/CE del concilio.
Questa dichiarazione è applicabile ai prodotti cui sono
applicati i marchi CE.
30. 8. 2002
Y. Hirano (EMO)
3
4
5
6
7
0
9
8
0
9
8
0
8
9
6
B
A
C
D
E
DH 40MR
Rotary Hammer
Bohrhammer
Perforateur percussion
Martello perforatore
Boorhamer
Martillo perforador
Martelo perfurador
Συρδραπαν περιςτρικ
1
Read through carefully and understand these instructions before use.
Diese Anleitung vor Benutzung des Werkzeugs sorgfältig durchlesen und verstehen.
Lire soigneusement et bien assimiler ces instructions avant usage.
Prima dell’uso leggere attentamente e comprendere queste istruzioni.
Deze gebruiksaanwijzing s.v.p. voor gebruik zorgvuldig doorlezen.
Leer cuidadosamente y comprender estas instrucciones antes del uso.
Antes de usar, leia com cuidado para assimilar estas instruções.
∆ιαάστε πρσεκτικά και κατανήσετε αυτές τις δηγίες πριν τη ρήση.
208
Code No. C99118371 N
Printed in Japan
Handling instructions
Bedienungsanleitung
Mode d’emploi
Istruzioni per l’uso
Gebruiksaanwijzing
Instrucciones de manejo
Instruções de uso
δηγίες ειρισµύ
3
6
9
12
2
5
8
11
1
2
1
4
7
10
Hitachi Power Tools Europe GmbH
Siemensring 34, 47877 Willich, F. R. Germany
Hitachi Koki Co., Ltd.
Shinagawa Intercity Tower A, 15-1, Konan 2-chome,
Minato-ku, Tokyo, Japan
Nederlands
EC VERKLARING VAN CONFORMITEIT
Wij verklaren onder eigen verantwoordelijkheid dat dit
produkt conform de richtlijnen of gestandardiseerde
documenten EN50144, HD400, EN55014-1, EN55014-2,
EN61000-3-2, EN61000-3-3 en/of EN61000-3-11 voldoet
aan de eisen van EEG Bepalingen 73/23/EEG, 89/336/
EEG en/of 98/37/EC.
Deze verklaring is van toepassing op produkten
voorzien van de CE-markeringen.
Español
DECLARACIÓN DE CONFORMIDAD DE LA CE
Declaramos bajo nuestra única responsabilidad que
este producto está de acuerdo con las normas o con
los documentos de normalización EN50144, HD400,
EN55014-1, EN55014-2, EN61000-3-2, EN61000-3-3 y/o
EN61000-3-11, según indican las Directrices del Consejo
73/23/CEE, 89/336/CEE y/o 98/37/CE.
Esta declaración se aplica a los productos con marcas
de la CE.
Portugûes
DECLARAÇÃO DE CONFORMIDADE CE
Declaramos, sob nossa única e inteira responsabilidade,
que este produto está de acordo com as normas ou
documentos normativos EN50144, HD400, EN55014-1,
EN55014-2, EN61000-3-2, EN61000-3-3 e/ou EN61000-
3-11, em conformidade com as Diretrizes 73/23/CEE,
89/336/CEE e/ou 98/37/CE do Conselho.
Esta declaração se aplica aos produtos designados CE.
Ελληνικά
EK ∆ΗΛ·ΣΗ ΕΝΑΡΜΝΙΣΜΥ
∆ηλώνυµε µε απλυτη υπευθυντητα τι αυτ τ
πριν είναι εναρµνισµέν µε τα πρτυπα ή τα
έγραα πρτύπων EN50144, HD400, EN55014-1,
EN55014-2, EN61000-3-2, EN61000-3-3 και / ή EN61000-
3-11 σε συµωνία µε τις δηγίες τυ Συµυλίυ 73/
23/EOK, 89/336/EOK και/ή 98/37/EK.
Αυτή η δήλωση ισύει στ πριν µε τ σηµάδι CE.
English
EC DECLARATION OF CONFORMITY
We declare under our sole responsibility that this
product is in conformity with standards or standardized
documents EN50144, HD400, EN55014-1, EN55014-2,
EN61000-3-2, EN61000-3-3 and/or EN61000-3-11 in
accordance with Council Directives 73/23/EEC, 89/336/
EEC and/or 98/37/EC.
This declaration is applicable to the product affixed CE
marking.
Deutsch
ERKLÄRUNG ZUR KONFORMITÄT MIT CE-REGELN
Wir erklären mit alleiniger Verantwortung, daß dieses
Produkt den Standards oder standardisierten
Dokumenten EN50144, HD400, EN55014-1, EN55014-2,
EN61000-3-2, EN61000-3-3 und/oder EN61000-3-11 in
Übereinstimmung mit den Direktiven des Europarats
73/23/EWG, 89/336/EWG und/order 98/37/CE entspricht.
Diese Erklärung gilt für Produkte, die die CE-Markierung
tragen.
Français
DECLARATION DE CONFORMITE CE
Nous déclarons sous notre seule et entière respon-
sabilité que ce produit est conforme aux normes ou
documents normalisés EN50144, HD400, EN55014-1,
EN55014-2, EN61000-3-2, EN61000-3-3 et/ou EN61000-
3-11 en accord avec les Directives 73/23/CEE, 89/336/
CEE et/ou 98/37/CE du Conseil.
Cette déclaration s’applique aux produits désignés CE.
Italiano
DICHIARAZIONE DI CONFORMITÀ CE
Si dichiara sotto nostra responsabilità che questo
prodotto è conforme agli standard o ai documenti
standardizzati EN50144, HD400, EN55014-1, EN55014-
2, EN61000-3-2, EN61000-3-3 e/o EN61000-3-11
conforme alle direttive 73/23/CEE, 89/336/CEE e/o 98/
37/CE del concilio.
Questa dichiarazione è applicabile ai prodotti cui sono
applicati i marchi CE.
30. 8. 2002
Y. Hirano (EMO)
3
4
5
6
7
0
9
8
0
9
8
0
8
9
6
B
A
C
D
E
2
3
60
13
16
19
14
17
20
15
18
21
English Deutsch Français Italiano
1
2
3
4
5
6
7
8
9
0
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
Tool shank
Grease
Tool
Part of SDS max shank
Front cap
Grip
Dial
Button
Selector lever
Lever holder
Stopper
Side handle
Taper shank adapter
Drill bit (taper shank)
Indicating groove shows
standard depth matching
the outside diameter of
the anchor for drilling.
Cotter
Rest
Drill chuck
Chuck adapter
Core bit
Core bit shank
Guide plate
Center pin
Core bit tip
Crank cover
Wear limit
No. of Carbon Brush
Werkzeugschaft
Schmierfett
Werkzeug
Teii des SDS-max
Schaftes
Vordere Abdeckung
Spannbacke
Skalenscheibe
Knopf
Wahlhebel
Hebelhalter
Anschlagstange
Seitengriff
Konusschaftadapter
Bohren (mit konischem
Schaft)
Anzeigerille zeigt
Normalloch-tiefe gemäß
Außendurchmesser des
Ankers für Bohren.
Keil
Auflage
Bohrfutter
Bohrfutteradapter
Bohrkrone
Bohrkronenschenkel
Führengsplatte
Mittelstift
Bohrkronenspitze
Kurbelabdeckung
Verschleißgrenze
Nr. der Kohlebürste
Queue
Graisse
Outil
Elément de la tige SDS
max
Capuchon avant
Attache coulissante
Bague
Bouton
Sélecteur
Support de levier
Quenouille
Poignée latérale
Raccord de queue
conique
Mèche (Queue conique)
La rainure indicatrice
montre la profondeur
standard adaptée au
diamètre extérieur de
l’ancre pour le perçage.
Clavette
Support
Mandrin porte-foret
Raccord de mandrin
Couronne
Queue de couronne
Plaque de guidage
Goujon central
Bout de couronne
Cache de carter
Limite d’usure
No. de balai en carbone
Gambo
Grasso
Utensile
Parte dell’asta SDS max
Protezione davanti
Presa davanti
Manopola
Tasto
Leva di selezione
Supporto leva
Bacchetta d’arresto
Impugnatura laterale
Adattatore del gambo
conico
Punta del trapano
(gambo conico)
Scanalatura di
riferimento indicante la
profondità standard con
il diametro esterno
dell’ancora per il
trapanaggio.
Chiave trasversale
Appoggio
Mandrino
Adattatore per mandrino
Corona
Gambo della corona
Piastra di guida
Perno ralla
Punta della corona
Coperchio manovella
Limite d’usura
Numero delle spazzole
di carbone
J
K
N
J
M
L
J
K
22
C
F
G
5
6
4
I
H
J
K
O
73
17 mm
7 mm
P
Q
2
3
60
13
16
19
14
17
20
15
18
21
English Deutsch Français Italiano
1
2
3
4
5
6
7
8
9
0
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
Tool shank
Grease
Tool
Part of SDS max shank
Front cap
Grip
Dial
Button
Selector lever
Lever holder
Stopper
Side handle
Taper shank adapter
Drill bit (taper shank)
Indicating groove shows
standard depth matching
the outside diameter of
the anchor for drilling.
Cotter
Rest
Drill chuck
Chuck adapter
Core bit
Core bit shank
Guide plate
Center pin
Core bit tip
Crank cover
Wear limit
No. of Carbon Brush
Werkzeugschaft
Schmierfett
Werkzeug
Teii des SDS-max
Schaftes
Vordere Abdeckung
Spannbacke
Skalenscheibe
Knopf
Wahlhebel
Hebelhalter
Anschlagstange
Seitengriff
Konusschaftadapter
Bohren (mit konischem
Schaft)
Anzeigerille zeigt
Normalloch-tiefe gemäß
Außendurchmesser des
Ankers für Bohren.
Keil
Auflage
Bohrfutter
Bohrfutteradapter
Bohrkrone
Bohrkronenschenkel
Führengsplatte
Mittelstift
Bohrkronenspitze
Kurbelabdeckung
Verschleißgrenze
Nr. der Kohlebürste
Queue
Graisse
Outil
Elément de la tige SDS
max
Capuchon avant
Attache coulissante
Bague
Bouton
Sélecteur
Support de levier
Quenouille
Poignée latérale
Raccord de queue
conique
Mèche (Queue conique)
La rainure indicatrice
montre la profondeur
standard adaptée au
diamètre extérieur de
l’ancre pour le perçage.
Clavette
Support
Mandrin porte-foret
Raccord de mandrin
Couronne
Queue de couronne
Plaque de guidage
Goujon central
Bout de couronne
Cache de carter
Limite d’usure
No. de balai en carbone
Gambo
Grasso
Utensile
Parte dell’asta SDS max
Protezione davanti
Presa davanti
Manopola
Tasto
Leva di selezione
Supporto leva
Bacchetta d’arresto
Impugnatura laterale
Adattatore del gambo
conico
Punta del trapano
(gambo conico)
Scanalatura di
riferimento indicante la
profondità standard con
il diametro esterno
dell’ancora per il
trapanaggio.
Chiave trasversale
Appoggio
Mandrino
Adattatore per mandrino
Corona
Gambo della corona
Piastra di guida
Perno ralla
Punta della corona
Coperchio manovella
Limite d’usura
Numero delle spazzole
di carbone
J
K
N
J
M
L
J
K
22
C
F
G
5
6
4
I
H
J
K
O
73
17 mm
7 mm
P
Q
5
English
GENERAL OPERATIONAL PRECAUTIONS
WARNING! When using electric tools, basic safety
precautions should always be followed to reduce the
risk of fire, electric shock and personal injury, including
the following.
Read all these instructions before operating this product
and save these instructions.
For safe operations:
1. Keep work area clean. Cluttered areas and benches
invite injuries.
2. Consider work area environment. Do not expose
power tools to rain. Do not use power tools in
damp or wet locations. Keep work area well lit.
Do not use power tools where there is risk to
cause fire or explosion.
3. Guard against electric shock. Avoid body contact
with earthed or grounded surfaces. (e.g. pipes,
radiators, ranges, refrigerators).
4. Keep children away. Do not let visitors touch the
tool or extension cord. All visitors should be kept
away from work area.
5. Store idle tools. When not in use, tools should
be stored in a dry, high or locked up place, out
of reach of children.
6. Do not force the tool. It will do the job better and
safer at the rate for which it was intended.
7. Use the right tool. Do not force small tools or
attachments to do the job of a heavy duty tool.
Do not use tools for purposes not intended; for
example, do not use circular saw to cut tree limbs
or logs.
8. Dress properly. Do not wear loose clothing or
jewelry, they can be caught in moving parts.
Rubber gloves and non-skid footwear are
recommended when working outdoors. Wear
protecting hair covering to contain long hair.
9. Use eye protection. Also use face or dust mask
if the cutting operation is dusty.
10. Connect dust extraction equipment.
If devices are provided for the connection of dust
extraction and collection facilities ensure these are
connected and properly used.
11. Do not abuse the cord. Never carry the tool by
the cord or yank it to disconnect it from the
receptacle. Keep the cord away from heat, oil and
sharp edges.
12. Secure work. Use clamps or a vise to hold the
work. It is safer than using your hand and it frees
both hands to operate tool.
13. Do not overreach. Keep proper footing and balance
at all times.
14. Maintain tools with care. Keep cutting tools sharp
and clean for better and safer performance. Follow
instructions for lubrication and changing
accessories. Inspect tool cords periodically and if
damaged, have it repaired by authorized service
center. Inspect extension cords periodically and
replace, if damaged. Keep handles dry, clean, and
free from oil and grease.
15. Disconnect tools. When not in use, before servicing,
and when changing accessories such as blades,
bits and cutters.
16. Remove adjusting keys and wrenches. Form the
habit of checking to see that keys and adjusting
wrenches are removed from the tool before turning
it on.
17. Avoid unintentional starting. Do not carry a
plugged-in tool with a finger on the switch. Ensure
switch is off when plugging in.
18. Use outdoor extension leads. When tool is used
outdoors, use only extension cords intended for
outdoor use.
19. Stay alert. Watch what you are doing. Use common
sense. Do not operate tool when you are tired.
20. Check damaged parts. Before further use of the
tool, a guard or other part that is damaged should
be carefully checked to determine that it will
operate properly and perform its intended function.
Check for alignment of moving parts, free running
of moving parts, breakage of parts, mounting and
any other conditions that may affect its operation.
A guard or other part that is damaged should be
properly repaired or replaced by an authorized
service center unless otherwise indicated in this
handling instructions. Have defective switches
replaced by an authorized service center. Do not
use the tool if the switch does not turn it on and
off.
21. Warning
The use of any accessory or attachment, other
than those recommended in this handling
instructions, may present a risk of personal injury.
22. Have your tool repaired by a qualified person.
This electric tool is in accordance with the relevant
safety requirements. Repairs should only be carried
out by qualified persons using original spare parts.
Otherwise this may result in considerable danger
to the user.
PRECAUTIONS ON USING ROTARY HAMMER
䡬 Wear earplugs to protect your ears during operation.
䡬 Do not touch the bit during or immediately after
operation. The bit becomes very hot during operation
and could cause serious burns.
䡬 Before starting to break, chip or drill into a wall,
floor or ceiling, thoroughly confirm that such items
as electric cables or conduits are not buried inside.
䡬 Always hold the body handle and side handle of
the power tool firmly. Otherwise the counterforce
produced may result in inaccurate and even
dangerous operation.
English
6
STANDARD ACCESSORIES
(1) Case (Molded plastic) ............................................... 1
(2) Side Handle ................................................................ 1
(3) Stopper ........................................................................ 1
(4) Hexagon Bar Wrench (for 6 mm screw) ............. 1
(5) Hexagon Bar Wrench (for 5 mm screw) ............. 1
(6) Hexagon Bar Wrench (for 4 mm screw) ............. 1
(7) Hammer Grease A .................................................... 1
Standard accessories are subject to change without
notice.
OPTIONAL ACCESSORIES (sold separately)
1. Through-hole drilling (Rotation + Hammering)
(1) Drill bit (SDS max shank)
2. Anchor hole drilling (Rotation + Hammering)
Drill bit (Taper shank)
Adapter for SDS-plus shank bit
3. Large dia. hole boring (Rotation + Striking)
(1) Center pin
䢇 Applied to core bits from 38 mm to 105 mm
䢇 Applied to core bits 32 mm and 35 mm
NOTE
Do not use core bits 25 mm or 29 mm.
(2) Core bit
䢇 External dia. 25, 29, 32, 35, 38, 45, 54, 64, 79, 94,
105 mm
(with guide plate, not applicable to cores 25 mm
or 29 mm)
(3) Core bit shank
䢇 Applied to core bits above 38 mm
䢇 Applied to core bits below 35 mm
4. Drilling holes .... For drilling metal and wooden
materials
(1) Drill bit
(SDS-plus shank)
(2) Adapter for SDS-plus
shank bit
(SDS max shank)
(2) Core
bit
(3) Core bit
shank
(Guide
plate)
(1) Center
pin
(3) Cotter
(1) Drill bit (taper shank)
External dia.: 11, 12.3, 12.7,
14.3, 14.5,
17.5 mm
(2) Taper shank
adapter
(SDS max shank)
13 mm drill chuck
(13VLA)
Chuck adapter
(SDS max shank)
Chuck wrench
SPECIFICATIONS
*Be sure to check the nameplate on product as it is subject to change by areas.
Voltage (by areas)* (110V, 115V, 120V, 127V, 220V, 230V, 240V)
Power input 950 W*
Capacity Drill bit: 40 mm
Core bit: 105 mm
No load speed 240 – 480 min
-1
Full-load impact rate 1320 – 2650 min
-1
Weight (without cord, side handle) 6.5 kg
Outer diameter (mm) Overall length (mm)
16
340, 540
19
22
320, 520
25
28
32
370, 570
38
40
Taper shank
Application drill bit
adapter
Morse taper Drill bit (taper shank)
(No. 1) 11, 12.3, 12.7, 14.3, 14.5, 17.5 mm
7
English
5. Bolt placing operation with Chemical Anchor.
(Rotation + Hammering)
6. Crushing (Hammering)
7. Groove digging and edging (Hammering)
8. Asphalt cutting (Hammering)
9. Scooping Work (Hammering)
10. Surface Roughing (Hammering)
11. Tamping (Hammering)
12. Syringe (for chip removal)
䡬 Hammer grease A
500 g (in a can)
70 g (in a green tube)
30 g (in a green tube)
Optional accessories are subject to change without
notice.
APPLICATIONS
䡬 Drilling holes in concrete
䡬 Drilling anchor holes
(Standard socket
on the market)
(SDS max shank)
12.7 mm Chemical
Anchor Adaptor
19 mm Chemical
Anchor Adaptor
(1) Bull point
Overall length: 280, 400 mm
(1) Cold chisel
Overall length: 280, 400 mm
(1) Cutter
(1) Scoop
(2) Shank
(1) Bushing Tool
(2) Shank
(1) Rammer
150 × 150 mm
䡬 Crushing concrete, chipping, digging, and squaring
(by applying optional accessories)
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a power receptacle while
the power switch is in the ON position, the power
tool will start operating immediately, which could
cause a serious accident.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
4. How to install tool
NOTE
For tools such as a bull point and a cold chisel,
use only Hitachi genuine parts.
(1) Clean, then smear the tool shank with the grease
provided in the green tube (Fig. 1).
(2) To attach the tool (SDS max shank), insert it into
the hole until it contacts the innermost end of the
hole as illustrated in Fig. 2.
If you continue to turn the tool with slight pressure,
you can feel a spot where there is a hitch. At that
spot, pull the grip to the direction of an arrow mark
and insert the tool all the way until it hits the
innermost end.
Releasing the grip reverts the grip and secures the
tool in place.
(3) Pull the tool to make sure it is locked completely.
(4) To remove the tool, fully pull the grip in the direction
of the arrow and pull out the tool.
5. Regulating the number of rotations and hammering
(Fig. 3)
This Rotary Hammer is equipped with a built-in
electronic control circuit that can adjust and regulate
the number of rotations and times of hammering.
This Rotary Hammer can be used by adjusting the
dial, depending upon the contents of operation,
such as boring holes into fragile materials, chipping,
centering, etc.
The scale ‘1’ of the dial is designed for a minimum
speed with the number of 240 rotations per minute
and 1320 times of blow per minute. The scale ‘6’
is designed for a maximum speed with the number
of 480 rotations per minute and 2650 times of blow
per minute.
CAUTION:
Do not adjust the dial during operation. Doing so
can result in injury because the Rotary Hammer
must be held by only one hand, disabling the steady
control of the Rotary Hammer.
HOW TO USE THE ROTARY HAMMER
1. How to drill holes (Fig. 4)
(1) Pull the switch trigger after applying the drill bit
tip to the drilling position.
English
8
5. Install the stopper (Fig. 10)
(1) Loosen the side handle and insert the straight portion
of the stopper into the handle bolt hole.
(2) Move the stopper to the specified position and
rotate the grip of the side handle clockwise to fix
the stopper.
6. Warming up (Fig. 11)
The grease lubrication system in this unit may
require warming up in cold regions.
Position the end of the bit so makes contact with
the concrete, turn on the switch and perform the
warming up operation. Make sure that a hitting
sound is produced and then use the unit.
CAUTION
When the warming up operation is performed, hold
the side handle and the main body securely with
both hands to maintain a secure grip and be careful
not to twist your body by the jammed drill bit.
DRILLING AND DRIVING-IN OPERATIONS FOR
ANCHORS
1. When a taper shank adapter is used. (Fig. 12)
(1) Install drill bit with taper shank in the taper shank
adapter.
(2) Turn the power on and drill a base hole to the depth
sounded by indicating groove on the drill bit.
(3) After cleaning out dust with a syringe, attach the
plug to the anchor tip and drive in the anchor with
a manual hammer.
(4) To remove the drill bit (taper shank), insert the
cotter into the slot of the taper shank adapter and
strike the head of the cotter with a manual hammer
supporting on a rest. (Fig. 13)
USING DRILL CHUCK, CHUCK ADAPTER
Note that this machine can be used at “rotation only”
if separately sold parts such as drill chuck and chuck
adapter are attached. Use it with the selector lever
positioned at “rotation + hammering”.
CAUTION:
During operation, be sure to grip the handle and
the side handle firmly to prevent your body from
swaying.
(1) Switching to “rotation + hammering”
For switching to “rotation + hammering”, follow the
same procedures mentioned in [3. When drilling at
“rotation + hammering”].
(2) Attaching chuck adapter to drill chuck (Fig. 14)
(a) Attach the chuck adapter to the drill chuck.
(b) The SDS max shank of the chuck adapter is
equivalent to the drill bit. Therefore, follow the
same procedure as [How to install tool] for
attaching and detaching.
(3) Drilling
(a) Even if you apply more-than-required pressure to
the machine body, drilling can never be performed
as quickly as you expect. Applying more force or
pressure to the machine body than what is needed,
on the contrary, damages the drill tip, resulting in
the declined working efficiency and shortened life
of this machine.
(b) A drill can snap sometimes when drilling is almost
finished. It is important to relax your thrusting
pressure when drilling is nearing the end.
(2) It is unnecessary to forcibly press the rotary hammer
main body. It is sufficient to slightly press the rotary
hammer to an extent that shavings are freely
discharged.
CAUTION
Although this machine is equipped with a safety
clutch, if the drill bit becomes bound in concrete
or other material, the resultant stoppage of the drill
bit could cause the machine body to turn in reaction.
Ensure that the main handle and side handle are
gripped firmly during operation.
2. How to chisel or crush (Fig. 5)
By applying the drill bit tip to the chiseling or
crushing position, operate the rotary hammer by
utilizing its empty weight.
Forcible pressing or thrusting is unnecessary.
3. When drilling at “rotation + hammering”:
CAUTION:
If you switch the selector lever during motor rotation,
the tool can start to rotate abruptly, resulting in
unexpected accidents. Be sure to switch the selector
lever when the motor is at a complete stop.
(1) Switching to “rotation + hammering”
(a) Push the button, release lock and turn the selector
lever clockwise.
(b) Align ▲ of the selector lever and
of the lever
holder as illustrated in Fig. 6.
(c) Release the button to lock the selector lever.
NOTE:
Turn the selector lever (do not push the button) to
check if it is completely locked and make sure that
it does not turn.
4. When chipping and chiseling at “hammering”:
CAUTION:
䡬 If the selector lever is switched during motor rotation,
the tool can start to rotate abruptly, resulting in
unexpected accidents. Make sure to switch the
selector lever when the motor is at a complete stop.
䡬 If the bull point or cold chisel is used at the position
of ”rotation + hammering”, the tool can start to
rotate, resulting in unexpected accidents. Make
sure that they are used at the position of
”hammering”.
(1) Switching to ”hammering”
(a) Push the button, release lock and turn the selector
lever counterclockwise.
(b) Align ▲ of the selector lever and
of the lever
holder as illustrated in Fig. 7.
(c) Release the button to lock the selector lever.
NOTE:
Turn the selector lever (do not push the button) to
check if it is completely locked and make sure that
it does not turn.
(2) When fixing working positions of tools such as cold
chisel, etc.,
(a) Push the button, release lock and turn the selector
lever.
Align ▲ of the selector lever and
of the lever
holder as illustrated in Fig. 8.
(b) Release the button to lock the selector lever.
(c) Turn the grip as illustrated in Fig. 9 and fix the
tool to the desired working direction.
(d) Switch the selector lever to “hammering”
according to the procedures mentioned in the
above item (1) and secure the position of the tool.
9
English
HOW TO HANDLE A CORE BIT
When a core bit is used, large diameter holes and blind
holes can be drilled. In this case, use optional
accessories for core bits (such as a center pin and core
bit shank) for more efficient operation.
1. Mounting
CAUTION
Prior to mounting a core bit, always disconnect the
plug from the power supply receptacle.
(1) Mount the core bit on the core bit shank. (Fig. 15)
Before that, feed oil to the screw portion of core
bit shank for easy dismounting.
(2) Mount the core bit shank on the main body in the
same manner as in mounting the drill bit and the
bull point. (Fig. 16)
(3) Insert the center pin into the guide plate until it
reaches the extremity.
(4) Fit in the guide plate by aligning its concaved
portion with the core bit tip. When the position of
the concave is shifted by turning the guide plate
right or left, the guide plate never slips off even
when the drill is used in a downward direction.
(Fig. 17)
2. Drilling holes
(1) Insert the plug into a receptacle.
(2) A spring is built in the center pin. By straightly and
gently pressing it to the wall or floor surface, the
entire surface of the core bit tip attains contact to
start the hole drilling job. (Fig. 18)
(3) When the hole depth reaches approximately 5 mm,
the hole position can be determined. Then remove
the center pin and guide plate from the core bit
and continue the hole drilling job.
CAUTION
When removing the center pin and guide plate,
always disconnect the plug from the receptacle.
3. How to dismount the core bit
䡬 By holding the rotary hammer (with the core bit
inserted) in an upward position, drive the rotary
hammer to repeat impact operation two or three
times, whereby the screw is loosened and the rotary
hammer becomes ready for disassembly. (Fig. 19)
䡬 Remove the core bit shank from the rotary hammer,
hold the core bit with one hand, and strongly strike
the head of the SDS max shank portion of the core
bit shank with a manual hammer two or three
times, whereby the round head screw is loosened
and the rotary hammer is ready for disassembly.
(Fig. 20)
HOW TO REPLACE GREASE
This machine is of full air-tight construction to protect
against dust and to prevent lubricant leakage. Therefore,
the machine can be used without lubrication for long
periods. Replace the grease as described below.
1. Grease replacement period
After purchase, replace grease after every 6 months
of usage. Ask for grease replacement at the nearest
Hitachi authorized Service center. Proceed for
replacement of grease.
2. Grease replenishment
CAUTION
Before replenishing the grease, turn the power off
and pull out the power plug.
(1) Remove the crank cover and wipe off the grease
inside. (Fig. 21)
(2) Supply 30g of Hitachi Electric Hammer Grease A
(Standard accessory, contained in tube) to the crank
case.
(3) After replenishing the grease, install the crank cover
securely.
NOTE
The Hitachi Electric Hammer Grease A is of the low
viscosity type. If necessary purchase from an Hitachi
authorized Service center.
MAINTENANCE AND INSPECTION
1. Inspecting the tool
Since use of a dull tool will degrade efficiency and
cause possible motor malfunction, sharpen or
replace the tool as soon as abrasion is noted.
2. Inspecting the mounting screws:
Regularly inspect all mounting screws and ensure
that they are properly tightened. Should any of the
screws be loose, retighten them immediately. Failure
to do so could result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very “heart” of the
power tool. Exercise due care to ensure the winding
does not become damaged and/or wet with oil or
water.
4. Inspecting the carbon brushes (Fig. 22)
The Motor employs carbon brushes which are
consumable parts. When they become worn to or
near the “wear limit”, it could result in motor trouble.
When an auto-stop carbon brush is equipped, the
motor will stop automatically. At that time, replace
both carbon brushes with new ones which have the
same carbon brush Numbers shown in the figure.
In addition, always keep carbon brushes clean and
ensure that they slide freely within the brush holders.
5. Replacing carbon brushes
Loosen the two set screws and remove the tail
cover. Remove the brush caps and carbon brushes.
After replacing the carbon brushes, tighten the brush
caps securely and install the tail cover with securely
tightening two set screws.
6. Service parts list
A: Item No.
B: Code No.
C: No. Used
D: Remarks
CAUTION
Repair, modification and inspection of Hitachi Power
Tools must be carried out by an Hitachi Authorized
Service Center.
This Parts List will be helpful if presented with the
tool to the Hitachi Authorized Service Center when
requesting repair or other maintenance.
In the operation and maintenance of power tools,
the safety regulations and standards prescribed in
each country must be observed.
MODIFICATIONS
Hitachi Power Tools are constantly being improved
and modified to incorporate the latest technological
advancements.
Accordingly, some parts (i.e. code numbers and/or
design) may be changed without prior notice.
English
10
NOTE
Due HITACHI’s continuing program of research and
development, the specifications herein are subject to
change without prior notice.
IMPORTANT
Correct connection of the plug
The wires of the main lead are coloured in accordance
with the following code:
Blue: — Neutral
Brown: — Live
As the colours of the wires in the main lead of this
tool may not correspond with the coloured markings
identifying the terminals in your plug proceed as follows:
The wire coloured blue must be connected to the
terminal marked with the letter N or coloured black.
The wire coloured brown must be connected to the
terminal marked with the letter L or coloured red.
Neither core must be connected to the each terminal.
NOTE
This requirement is provided according to BRITISH
STANDARD 2769: 1984.
Therefore, the letter code and colour code may not be
applicable to other markets except The United Kingdom.
Information concerning airborne noise and vibration
The measured values were determined according to
EN50144.
The typical A-weighted sound pressure level: 92 dB (A)
The typical A-weighted sound power level: 105 dB (A)
Wear ear protection.
The typical weighted root mean square acceleration
value: 6.9 m/s
2
55
56
A B C D
1 321-306 1
2 321-305 1
3 318-590 1
4 321-304 1
5 948-131 1
6 600-7DD 1 6007DDUAV2S
7 313-421 2 D8×20
8 321-286 1
9 313-396 1
10 321-287 1
11 321-303 1
12 321-302 1
13 981-942 4 M6×25
14 321-300 1
15 956-996 1 1AS-60
16 321-301 1
17 981-859 1
18 315-868 1
19 321-297 1
20 321-288 1
21 321-289 1
22 321-290 1
23 313-057 4 D6×6
24 321-291 1
25 321-298 1
26 321-299 1
27 321-293 1
28 321-274 1
29 321-292 1
30 310-420 1
31 321-295 1
32 986-104 1
33 321-284 1
34 980-708 1
35 321-285 1
36 321-296 1
38 ———— 1
39 321-315 1
40 ———— 1
41 321-314 1
42 939-540 1
43 321-275 1
44 944-109 1 3×3×8
45 620-3DD 1 6203DDCMPS2L
46 996-363 1 S-40
47 321-274 1
48 321-273 1
49 986-940 4 M6×45
50 944-109 1 3×3×8
51 321-279 1
52 313-050 1
53 600-2DD 1 6002DDCMPS2L
54 313-058 1
55 313-053 1
56 321-281 1
57 321-282 10
58 320-343 10
59 321-280 1
60 321-283 1
61 629-VVM 1 629VVC2PS2L
62 321-2377 1 “11-22”
63 944-525 1
64 313-078 1
A B C D
65 313-080 1
66 971-786 1
67 ———— 1
68 983-162 5 M4×12
69 313-079 1
70 321-309 1
71 311-229 1
72 321-308 1
73 321-307 1
74 873-095 1 P-16
75 321-310 1
76 321-311 1
77 321-312 1 D2×10
78 321-276 1
79 939-299 1 M661
80 321-319 1
81 620-1DD 1 6201DDCMPS2L
82 302-429 1
83 1 360-591U 1 110V-120V “87-90”
83 2 360-591E 1 220V-230V
83 3 360-591F 1 240V
85 953-174 2 D5×55
86 1 340-542C 1 110V “117, 118”
86 2 340-542G 1 120V “117, 118”
86 3 340-542E 1 220V-230V “117, 118”
86 4 340-542F 1 240F
87 982-631 1
88 608-VVM 1 608VVC2PS2L
89 321-320 1
90 930-703 2
92 321-322 1
93 321-318 1 “85, 86”
94 321-313 2 M6×22
95 935-829 2
96 999-073 2
97 971-001 2
98 321-321 1
99 877-839 2 M5×10
100 321-323 1
101 998-485 6 M5×14
102 313-093 1
103 321-324 1
104 301-653 2 D4×20
105 321-317 1
106 1 321-327 1 110V
106 2 321-326 1 120V
106 3 321-328 1 220V-240V
107 980-063 1
108 1 958-049 1 D8.2
108 2 940-778 1 D10.1
109 1 960-266 1
109 2 981-987Z 1 “SUI”
110 984-750 2 D4×16
111 ———— 1
112 959-141 1
113 938-307 1
501 321-325 1
502 981-840 1 30G
503 943-277 1 3MM
504 944-458 1 4MM
505 944-459 1 5MM
58
English
Nederlands
GUARANTEE CERTIFICATE
1 Model No.
2 Serial No.
3 Date of Purchase
4 Customer Name and Address
5 Dealer Name and Address
(Please stamp dealer name and address)
Italiano Ελληνικά
Français Português
Deutsch
Español
GARANTIEBEWIJS
1 Modelnummer
2 Serienummer
3 Datum van aankoop
4 Naam en adres van de gebruiker
5 Naam en adres van de handelaar
(Stempel a.u.b. naam en adres vande de
handelaar)
GARANTIESCHEIN
1 Modell-Nr.
2 Serien-Nr.
3 Kaufdaturn
4 Name und Anschrift des Kunden
5 Name und Anschrift des Händlers
(Bitte mit Namen und Anschrift des
Handlers abstempeln)
CERTIFICADO DE GARANTIA
1 Nùmero de modelo
2 Mùmero de serie
3 Fecha de adquisición
4 Nombre y dirección del cliente
5 Nombre y dirección del distribudor
(Se ruega poner el sellú del distribudor
con su nombre y dirección)
CERTIFICAT DE GARANTIE
1 No. de modèle
2 No de série
3 Date d'achat
4 Nom et adresse du client
5 Nom et adresse du revendeur
(Cachet portant le nom et l'adresse du
revendeur)
CETTIFICADO DE GARANTIA
1 Nùmero do modelo
2 Nùmero do série
3 Data de compra
4 Nome e morada do cliente
5 Nome e morada do distribuidor
(Por favor, carímbe o nome e morada
do distribuidor)
CERTIFICATO DI GARANZIA
1 Modello
2 N° di serie
3 Data di acquisto
4 Nome e indirizzo dell'acquirente
5 Nome e indirizzo del rivenditore
(Si prega di apporre il timbro con questi
dati)
ΠΙΣΤΠΙΗΤΙΚ ΕΓΓΥΗΣΗΣ
1 Αρ. Μντέλυ
2 Αύων Αρ.
3 Ηµερµηνία αγράς
4 ΄νµα και διεύθυνση πελάτη
5 ΄νµα και διεύθυνση µεταπωλητή
(Παρακαλύµε να ρησιµπιηθεί
σραγίδα)
✄
59
1
2
3
4
5
✄
DH 40MR
Rotary Hammer
Bohrhammer
Perforateur percussion
Martello perforatore
Boorhamer
Martillo perforador
Martelo perfurador
Συρδραπαν περιςτρικ
1
Read through carefully and understand these instructions before use.
Diese Anleitung vor Benutzung des Werkzeugs sorgfältig durchlesen und verstehen.
Lire soigneusement et bien assimiler ces instructions avant usage.
Prima dell’uso leggere attentamente e comprendere queste istruzioni.
Deze gebruiksaanwijzing s.v.p. voor gebruik zorgvuldig doorlezen.
Leer cuidadosamente y comprender estas instrucciones antes del uso.
Antes de usar, leia com cuidado para assimilar estas instruções.
∆ιαάστε πρσεκτικά και κατανήσετε αυτές τις δηγίες πριν τη ρήση.
208
Code No. C99118371 N
Printed in Japan
Handling instructions
Bedienungsanleitung
Mode d’emploi
Istruzioni per l’uso
Gebruiksaanwijzing
Instrucciones de manejo
Instruções de uso
δηγίες ειρισµύ
3
6
9
12
2
5
8
11
1
2
1
4
7
10
Hitachi Power Tools Europe GmbH
Siemensring 34, 47877 Willich, F. R. Germany
Hitachi Koki Co., Ltd.
Shinagawa Intercity Tower A, 15-1, Konan 2-chome,
Minato-ku, Tokyo, Japan
Nederlands
EC VERKLARING VAN CONFORMITEIT
Wij verklaren onder eigen verantwoordelijkheid dat dit
produkt conform de richtlijnen of gestandardiseerde
documenten EN50144, HD400, EN55014-1, EN55014-2,
EN61000-3-2, EN61000-3-3 en/of EN61000-3-11 voldoet
aan de eisen van EEG Bepalingen 73/23/EEG, 89/336/
EEG en/of 98/37/EC.
Deze verklaring is van toepassing op produkten
voorzien van de CE-markeringen.
Español
DECLARACIÓN DE CONFORMIDAD DE LA CE
Declaramos bajo nuestra única responsabilidad que
este producto está de acuerdo con las normas o con
los documentos de normalización EN50144, HD400,
EN55014-1, EN55014-2, EN61000-3-2, EN61000-3-3 y/o
EN61000-3-11, según indican las Directrices del Consejo
73/23/CEE, 89/336/CEE y/o 98/37/CE.
Esta declaración se aplica a los productos con marcas
de la CE.
Portugûes
DECLARAÇÃO DE CONFORMIDADE CE
Declaramos, sob nossa única e inteira responsabilidade,
que este produto está de acordo com as normas ou
documentos normativos EN50144, HD400, EN55014-1,
EN55014-2, EN61000-3-2, EN61000-3-3 e/ou EN61000-
3-11, em conformidade com as Diretrizes 73/23/CEE,
89/336/CEE e/ou 98/37/CE do Conselho.
Esta declaração se aplica aos produtos designados CE.
Ελληνικά
EK ∆ΗΛ·ΣΗ ΕΝΑΡΜΝΙΣΜΥ
∆ηλώνυµε µε απλυτη υπευθυντητα τι αυτ τ
πριν είναι εναρµνισµέν µε τα πρτυπα ή τα
έγραα πρτύπων EN50144, HD400, EN55014-1,
EN55014-2, EN61000-3-2, EN61000-3-3 και / ή EN61000-
3-11 σε συµωνία µε τις δηγίες τυ Συµυλίυ 73/
23/EOK, 89/336/EOK και/ή 98/37/EK.
Αυτή η δήλωση ισύει στ πριν µε τ σηµάδι CE.
English
EC DECLARATION OF CONFORMITY
We declare under our sole responsibility that this
product is in conformity with standards or standardized
documents EN50144, HD400, EN55014-1, EN55014-2,
EN61000-3-2, EN61000-3-3 and/or EN61000-3-11 in
accordance with Council Directives 73/23/EEC, 89/336/
EEC and/or 98/37/EC.
This declaration is applicable to the product affixed CE
marking.
Deutsch
ERKLÄRUNG ZUR KONFORMITÄT MIT CE-REGELN
Wir erklären mit alleiniger Verantwortung, daß dieses
Produkt den Standards oder standardisierten
Dokumenten EN50144, HD400, EN55014-1, EN55014-2,
EN61000-3-2, EN61000-3-3 und/oder EN61000-3-11 in
Übereinstimmung mit den Direktiven des Europarats
73/23/EWG, 89/336/EWG und/order 98/37/CE entspricht.
Diese Erklärung gilt für Produkte, die die CE-Markierung
tragen.
Français
DECLARATION DE CONFORMITE CE
Nous déclarons sous notre seule et entière respon-
sabilité que ce produit est conforme aux normes ou
documents normalisés EN50144, HD400, EN55014-1,
EN55014-2, EN61000-3-2, EN61000-3-3 et/ou EN61000-
3-11 en accord avec les Directives 73/23/CEE, 89/336/
CEE et/ou 98/37/CE du Conseil.
Cette déclaration s’applique aux produits désignés CE.
Italiano
DICHIARAZIONE DI CONFORMITÀ CE
Si dichiara sotto nostra responsabilità che questo
prodotto è conforme agli standard o ai documenti
standardizzati EN50144, HD400, EN55014-1, EN55014-
2, EN61000-3-2, EN61000-3-3 e/o EN61000-3-11
conforme alle direttive 73/23/CEE, 89/336/CEE e/o 98/
37/CE del concilio.
Questa dichiarazione è applicabile ai prodotti cui sono
applicati i marchi CE.
30. 8. 2002
Y. Hirano (EMO)
3
4
5
6
7
0
9
8
0
9
8
0
8
9
6
B
A
C
D
E
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
Hitachi DH 40MR Handling Instructions Manual
- Categoria
- Utensili elettrici
- Tipo
- Handling Instructions Manual
in altre lingue
- English: Hitachi DH 40MR
Documenti correlati
-
Hitachi DH 40FR Manuale utente
-
-
-
-
-
-
-
-
Hitachi DH 22PH Manuale del proprietario
-
Hitachi DH24DVA Manuale utente