Yamaha RX-V990 Manuale utente

Marca: Yamaha

Modello: RX-V990

Categoria: Lettori di cassette

Tipo: Manuale utente

RX-V990

Natural Sound Stereo Receiver

Récepteur stéréo “Son Naturel”

OWNER’S MANUAL

MODE D’EMPLOI

SAFETY INSTRUCTIONS

7 Wall or Ceiling Mounting — The unit should be mounted

to a wall or ceiling only as recommended by the

manufacturer.

8 Ventilation — The unit should be situated so that its

location or position does not interfere with its proper

ventilation. For example, the unit should not be situated

on a bed, sofa, rug, or similar surface, that may block

the ventilation openings; or placed in a built-in

installation, such as a bookcase or cabinet that may

impede the flow of air through the ventilation openings.

9 Heat — The unit should be situated away from heat

sources such as radiators, stoves, or other appliances

that produce heat.

10 Power Sources — The unit should be connected to a

power supply only of the type described in the operating

instructions or as marked on the unit.

11 Power-Cord Protection — Power-supply cords should be

routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying

particular attention to cords at plugs, convenience

receptacles, and the point where they exit from the unit.

12 Cleaning — The unit should be cleaned only as

recommended by the manufacturer.

13 Nonuse Periods — The power cord of the unit should be

unplugged from the outlet when left unused for a long

period of time.

14 Object and Liquid Entry — Care should be taken so that

objects do not fall into and liquids are not spilled into the

inside of unit.

15 Damage Requiring Service — The unit should be

serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged;

B. Objects have fallen, or liquid has been spilled into the

unit; or

C. The unit has been exposed to rain; or

D. The unit does not appear to operate normally or exhibits

a marked change in performance; or

E. The unit has been dropped, or the enclosure damaged.

16 Servicing — The user should not attempt service the

unit beyond those means described in the operating

instructions. All other servicing should be referred to

qualified service personnel.

17 Power Lines — An outdoor antenna should be located

away from power lines.

18 Grounding or Polarization — Precautions should be

taken so that the grounding or polarization is not

defeated.

1 Read Instructions — All the safety and operating

instructions should be read before the unit is operated.

2 Retain Instructions — The safety and operating

instructions should be retained for future reference.

3 Heed Warnings — All warnings on the unit and in the

operating instructions should be adhered to.

4 Follow Instructions — All operating and other

instructions should be followed.

5 Water and Moisture — The unit should not be used near

water – for example, near a bathtub, washbowl, kitchen

sink, laundry tub, in a wet basement, or near a

swimming pool, etc.

6 Carts and Stands — The unit should be used only with

a cart or stand that is recommended by

the manufacturer.

6A An unit and cart combination should be

moved with care. Quick stops,

excessive force, and uneven surfaces

may cause the unit and cart combination to overturn.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol, within an equilateral

triangle, is intended to alert you to the presence of uninsulated

“dangerous voltage” within the product’s enclosure that may be

of sufficient magnitude to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral triangle is intended

to alert you to the presence of important operating and

maintenance (servicing) instructions in the literature

accompanying the appliance.

IMPORTANT!

Please record the serial number of this unit in the space

below.

Model:

Serial No.:

The serial number is located on the rear of the unit.

Retain this Owner’s Manual in a safe place for future

reference.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

FCC INFORMATION

1. IMPORTANT NOTICE: DO NOT MODIFY THIS

UNIT! This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved

by Yamaha may void your authority, granted by the

FCC, to use the product.

IMPORTANT: When connecting this product to

accessories and/or another product use only high

quality shielded cables. Cable/s supplied with this

product MUST be used. Follow all installation

instructions. Failure to follow instructions could void

your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to

comply with the requirements listed in FCC

Regulations, Part 15 for Class “B” digital devices.

Compliance with these requirements provides a

reasonable level of assurance that your use of this

product in a residential environment will not result in

harmful interference with other electronic devices.

This equipment generates/uses radio frequencies

and, if not installed and used according to the

instructions found in the users manual, may cause

interference harmful to the operation of other

electronic devices.

Compliance with FCC regulations does not guarantee

that interference will not occur in all installations. If

this product is found to be the source of interference,

which can be determined by turning the unit “OFF”

and “ON”, please try to eliminate the problem by using

one of the following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch

(circuit breaker of fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/

reorient the antenna. If the antenna lead-in is 300

ohm ribbon lead, change the lead-in to coaxial type

cable.

If these corrective measures do not produce

satisfactory results, please contact the local retailer

authorized to distribute this type of product. If you can

not locate the appropriate retailer, please contact

Yamaha Electronics Corp., U.S.A. 6600 Orangethorpe

Ave, Buena Park, CA 90620

The above statement apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

19 Outdoor Antenna Grounding — If an outside antenna is

connected to this unit, be sure the antenna system is

grounded so as to provide some protection against

voltage surges and built-up static charges. Article 810 of

the National Electrical Code, ANSI/NFPA 70, provides

information with regard to proper grounding of the mast

and supporting structure, grounding of the lead-in wire

to an antenna discharge unit, size of grounding

conductors, location of antenna discharge unit,

connection to grounding electrodes, and requirements

for the grounding electrode.

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERIVCE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

NEC – NATIONAL ELECTRICAL CODE

ELECTRIC

SERVICE

EQUIPMENT

GROUND

CLAMP

MAST

ANTENNA

LEAD IN

WIRE

EXAMPLE OF ANTENNA GROUNDING

Note to CATV system installer:

This reminder is provided to call the CATV system

installer’s attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in

particular, specifies that the cable ground shall be

connected to the grounding system of the building, as

close to the point of cable entry as practical.

CAUTION (FOR CANADA MODEL)

TO PREVENT ELECTRIC SHOCK, MATHC WIDE

BLADE OF PLUG TO WIDE SLOT AND FULLY INSERT.

FOR CANADIAN CUSTOMERS

THIS DIGITAL APPARATUS DOES NOT EXCEED THE

“CLASS B” LIMITS FOR RADIO NOISE EMISSIONS

FROM DIGITAL APPARATUS SET OUT IN THE

RADIO INTERFERENCE REGULATIONS OF THE

CANADIAN DEPARTMENT OF COMMUNICATIONS.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT

1 To ensure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

2 Install your unit in a cool, dry, clean place – away from

windows, heat sources, and too much vibration, dust,

moisture or cold. Avoid sources of hum (transformers,

motors). To prevent fire or electrical shock, do not

expose to rain and water.

3 Do not operate the unit upside-down. It may overheat,

possibly causing damage.

4 Never open the cabinet. If a foreign object drops into

the set, contact your dealer.

5 Do not use force on switches, knobs or cords. When

moving the set, first turn the unit off. Then gently

disconnect the power plug and the cords connecting to

other equipment. Never pull the cord itself.

6 Do not attempt to clean the unit with chemical solvents;

this might damage the finish. Use a clean, dry cloth.

7 Always set the volume control to “–

∞

” before starting

the audio source play: increase the volume gradually to

an appropriate level after the play is started.

8 To prevent lightning damage, pull out the power cord

and remove the antenna cable during an electrical

storm.

9 Be sure to read the “Troubleshooting” section on

common operating errors before concluding that your

unit is faulty.

10 Do not connect audio equipment to the AC outlets on

the rear panel if that equipment requires more power

than the outlets are rated to provide.

11 When not planning to use this unit for long periods of

time (ie., vacation, etc.), disconnect the AC power plug

from the wall outlet.

The apparatus is not disconnected from the AC power

source as long as it is connected to the wall outlet, even

if the apparatus itself is turned off.

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s

Consumer Electronics Group want you to get the most out

of your equipment by playing it at a safe level. One that lets

the sound come through loud and clear without annoying

blaring or distortion – and, most importantly, without

affecting your sensitive hearing. Since hearing damage from

loud sounds is often undetectable until it is too

late, YAMAHA and the Electronic Industries

Association’s Consumer Electronics Group

recommend you to avoid prolonged exposure

from excessive volume levels.

Contents

PROFILE OF THIS UNIT....................................................7

SPEAKER SETUP FOR THIS UNIT...................................8

CONTROLS AND FUNCTIONS .......................................10

CONNECTIONS ...............................................................12

ADJUSTMENT BEFORE OPERATION............................18

BASIC OPERATIONS ......................................................21

TUNING OPERATIONS ...................................................24

USING THE DIGITAL SOUND FIELD

PROCESSOR (DSP) ........................................................28

SETTING THE SLEEP TIMER .........................................33

REMOTE CONTROL TRANSMITTER .............................34

ENGLISH

SUPPLIED ACCESSORIES

After unpacking, check that the following parts are contained.

• Remote Control Transmitter • Indoor FM Antenna

• Batteries (size AA, LR6, UM-3)

• Adapter for F-type connector

• User Program Sheets

• AM Loop Antenna

Remote

POWER

PLAY

TAPE 1

DIR A DIR B

SKIP

PHONO

TUNER

STOP

VCR 1

VCR 2

STOP PLAY

V–AUX

SLEEP TV VCR AUX

DISC

SKIP

PAUSE/STOP

DECK

A/B

PRESET

—

REC/PAUSEREC MUTE TAPE 2 MON

PLAY LD/TV

CHAPTER/CH

—

DISPLAY

MASTER

VOLUME

—

TEST

MUTING

—

TRANSMIT

/LEARN

DSP

HALL

EFFECT

CHURCH

CENTER LEVEL

REAR LEVEL

DELAY

TIME

MOVIE THEATER

JAZZ CLUB

STADIUM

PRO LOGIC

SURROUND

SPORTS

ENHANCED

ROCK

THEATER

70mm TV

YPC LEARN

USER

1234

5678

910

ON/OFF

RESET CLEAR

A B C D E

Features

• Five Speaker Configuration

Front: 100 W + 100 W (8Ω) RMS Output Power,

0.015% THD, 20-20,000 Hz

120 W + 120 W (6Ω) RMS Output Power,

0.04% THD, 20-20,000 Hz (USA Model Only)

Center: 100 W (8Ω) RMS Output Power,

0.015% THD, 1 kHz

Rear: 25 W + 25 W (8Ω) RMS Output Power,

0.08% THD, 1 kHz

• Digital Sound Field Processor

10 Programs including “Cinema DSP” 70mm Movie Theater

• 5 Channel Discrete Input for Dolby Surround Digital AC-3

• Automatic Input Balance Control for Dolby Pro Logic Surround

• Test Tone Generator for Easier Speaker Output Balance Adjustment

• 3 Center Channel Modes (NORMAL/WIDE/PHANTOM)

• 40-Station Random Access Preset Tuning

• Automatic Preset Tuning (FM only)

• Preset Station Shifting Capability (Preset Editing)

• IF Count Direct PLL Synthesizer Tuning System

• Video Signal Input/Output Capability

• SLEEP Timer

• Remote Control Capability

• Program and status messages superimposed on connected video monitor

ENGLISH

PROFILE OF THIS UNIT

You are the proud owner of a Yamaha stereo receiver –an extremely sophisticated audio component. The Digital

Sound Field Processor (DSP) built into this unit takes full advantage of Yamaha’s undisputed leadership in the

field of digital audio processing to bring you a whole new world of listening experiences. Follow the instructions in

this manual carefully when setting up your system, and this unit will sonically transform your room into a totally

new listening environments –movie theater, concert hall, and so on. In addition, you get incredible realism from

Dolby-encoded video sources using the built-in Dolby Pro Logic Surround Decoder.

Please read this owner’s manual carefully and store it in a safe place for later reference.

this same sound in your own listening room, so you’ll

feel all the sound of a live concert.

Furthermore, our technicians, armed with sophisti-

cated measuring equipment, have even made it

possible to capture the acoustics of a variety of venues

such as an actual concert hall, theater, etc. to allow

you to accurately recreate one of several actual live

performance environments, all in your own home.

Digital Sound Field Processing

What is it that makes live music so good? Today’s

advanced sound reproduction technology lets you get

extremely close to the sound of a live performance,

but chances are you’ll still notice something missing:

the acoustic environment of the live concert hall.

Extensive research into the exact nature of the sonic

reflections that create the ambience of a large hall has

made it possible for Yamaha engineers to bring you

Dolby Pro Logic Surround

The Dolby Pro Logic Surround Decoder program lets

you experience the dramatic realism and impact of

Dolby Surround movie theater sound in your own

home. Dolby Pro Logic gets its name from its profes-

sional-grade steering logic circuitry, which provides

greater effective front and rear channel separation for

a much higher degree of realism than the “passive”

Dolby Surround circuits found in less sophisticated

home audio/video equipment. Dolby Pro Logic

Surround provides a true center channel, so that there

are four independent channels, unlike passive Dolby

Surround which has in effect only three channels: left,

right, and rear. This center channel allows listeners

seated in even less-than-ideal positions to hear the

dialog originating from action on the screen while

getting a stereo effect as well.

This Dolby Pro Logic Surround Decoder employs a

digital signal processing system. This system in-

creases sound stability at each channel and minimizes

crosstalk between channels compared to conventional

analog Dolby signal processing.

In addition, this unit features a built-in automatic

input balance control. This circuit always presents

you the best surround conditions without performing

manual adjustments.

Dolby Pro Logic Surround + DSP

You can also enjoy Dolby Pro Logic with two modes

of Digital Sound field processing. These combinations

expand the surround effect. One is the “EN-

HANCED” Dolby Pro Logic Surround which recre-

ates the surround effect of the 35 mm film movie

theater. The other is the sound field program ”70 mm

MOVIE THEATER”. Which recreates the listening

experience of a 70mm film theater.

Directional Enhancement Circuit + DSP

The newly featured directional enhancement circuit

expands and focuses the digital sound field by

emphasizing position of sound.

This effect puts you in the midst of the action, while

centering and focusing your attention to the screen.

This circuit is available on the sound field program

“TV THEATER” and “SPORTS”.

CINEMA DSP

The YAMAHA “CINEMA DSP” logo indicates

these programs are created by the combination of

Dolby Pro Logic and YAMAHA DSP technology.

SPEAKER SETUP FOR THIS UNIT

SPEAKERS TO BE USED

This unit is designed to provide the best sound-field quality with a fivespeaker configuration. The speakers to be

used with this unit will be front speakers, rear speakers, and a center speaker.

The front speakers are used for the main source sound. These are usually a much larger, high-quality loudspeaker

than you will use for the surround sound effects. The center speaker is used for the center sound (dialog, etc.)

encoded with the Dolby Surround. And the rear speakers are used for special effects that enhance the surround

sound. The rear and center speakers do not need to be equal to the front speakers. However, all the speakers

should have high enough power handling to accept the maximum output of this unit.

SPEAKER CONFIGURATION

Five-Speaker Configuration

This configuration is the most effective and recom-

mended one. In this configuration, the center speaker

is used for dialog when you select the digital sound

field program DOLBY PRO LOGIC, DOLBY PRO

LOGIC ENHANCED, 70mm MOVIE THEATER, TV

THEATER, or SPORTS.

• Set the center channel mode to the “NORMAL” or

“WIDE” position. (For details, refer to page 19.)

Main L Center Main R

Dialogue

Surround sound

Dialogue

Surround sound

Rear L

Rear R

Four-Speaker Configuration

The center speaker is not used in this configuration. If

the digital sound field program DOLBY PRO LOGIC,

DOLBY PRO LOGIC ENHANCED, 70mm MOVIE

THEATER, TV THEATER, or SPORTS is selected, the

center sound along with the front effects are output

from the left and the right front speakers. However,

the sound effect of other programs can be the same as

that of the other configurations.

• Be sure to set the center channel mode to the

“PHANTOM” position. (For details, refer to page

19.)

Main L Main R

DialogueDialogue

Surround soundSurround sound

Dialogue

Surround sound

Rear L Rear R

ENGLISH

SPEAKER PLACEMENT

The recommended speaker configuration, the five-speaker configuration, will require two speaker pairs: front

speakers and rear speakers, plus a center speaker. When you place these speakers, refer to the following:

Front: In normal position. (The position of a standard

stereo speaker setup)

Center: Precisely between the front speakers. (To avoid

interference with TV sets, use a magnetically

shielded speaker.) When two center speakers are

used, place these to the right and left of your TV

set or video monitor.

Rear: Behind your listening position, facing slightly

inward. Nearly six feet (approx. 1.8 m) up from the

floor.

Rear L

Front R

Front L

Rear R

Center

1 POWER

Press to turn the RX-V990 on and off.

2 SPEAKERS A, B

Press button A or B to select a set of speakers.

(Press both buttons to select two sets of speakers,

or leave them off for headphone use.)

3 PHONES

Connect a set of headphones for private listening.

(Turn off the speakers 2 and the Digital Sound

Field Processor D. See page 23 for details; turn the

volume down to protect your hearing.)

4 TONE BYPASS

Press to bypass the Treble, and Bass controls (to

evaluate tone enhancements. See page 23 for

details).

5 BASS EXTENSION

Press to boost the low end frequencies to increase

the sound of the bass. See page 23 for details.

6 Tuner Section

Use the Tuner controls to store and select up to 40

AM or FM preset stations.

A/B/C/D/E - Repeatedly press this button to turn

through pages A through E to enter, edit, or select

preset stations in memory. Each page offers 8

presets.

PRESET STATIONS - Press button 1 through 8 to

access any of the 40 preset stations (used in

conjunction with the A/B/C/D/E button).

MEMORY - Press to place a new preset station in

memory.

EDIT - Press to edit preset stations.

TUNING MODE - Press to select the tuning mode

: Automatic or Manual.

FM/AM - Press to select FM or AM radio

reception.

TUNING - Press “Up” or “Down” to tune to the

frequency of the radio station you desire.

7 BASS

Turn to increase or decrease the low frequencies

(bass). See page 23 for details.

8 TREBLE

Turn to increase or decrease the high frequencies

(treble). See page 23 for details.

CONTROLS AND FUNCTIONS

DELAY TIME

CENTER REAR

CENTER

MODE

DOWN

TUNING

FM/AM

TUNING

MODE

EDIT

MEMORY

POWER

A/B/C/D/E

MAN’L/AUTO FM AUTO/MAN’L MONO

I 2345678

PRESET STATIONS

CINEMA DSP

NATURAL SOUND STEREO RECEIVER

RX–V990

LEVEL

PHANTOM

SPEAKERS

CINEMA DSP

PRO LOGIC

SPEAKERS

ENHANCED

SPEAKERS

PHONES

OFF

TONE

BYPASS

BASS TREBLE BALANCE

OFF

BASS

EXTENSION

REC OUT

LD/TV

VCR 1

TAPE 1

TUNER

PHONO

VIDEO AUX

VCR 2

SOURCE

345 7 8960A

ENGLISH

9 DSP Adjustment Control Section

CENTER MODE - When you are using Dolby Pro-

Logic, this button selects one of the three center

channel modes.

DELAY TIME - Increase (+) or decrease (–) the

delay time for each sound field D.

LEVEL

(CENTER, REAR) - Adjust the level of the

Center and Rear channels to achieve the best sound.

0 BALANCE

Turn to adjust the relative volume of the left and

right Front channels. See page 23 for details.

A REC OUT Selector

Use the Rec Out Selector to choose the source you

want to record. You can listen to another source

using the Input Selector E while recording. Set the

Rec Out Selector to “Source” when you want to

simultaneously record and listen to the input

source.

B VIDEO AUX Input

Connect a video source (camcorder, etc) to this

convenient front panel input. See page 16 for

details.

C VOLUME

Turn to adjust the master volume level of all

channels.

D DIGITAL SOUND FIELD PROCESSOR

Press the “Effect” button, then press one of the 10

DSP surround buttons to simulate various acoustic

environments. To turn off the surround sound,

press the “Effect” button again. See page 28 for

details.

E Input Selector

Press one of the input select buttons to select the

source you wish to hear and watch.

To listen to a 5CH DISCRT SOURCE, press the

LD/TV button so that “5CH DISCRT” appears on

the display. See page 30 for details.

CONTROLS AND FUNCTIONS

VOLUME

–dB

JAZZ CLUB

ROCK

CONCERT

HALL

PRO LOGIC

ENHANCED

THEATER

SPORTS

STADIUM

DIGITAL SOUND FIELD PROCESSOR

VIDEO AUX

VCR 2 VCR 1

LD/TV

TAPE 2

MONITOR

TUNER CD PHONO

EFFECT

MOVIE THEATER

70mm

CHURCH

TAPE 1

VIDEO AUX

8 VIDEO VIDEO L AUDIO R

2CH/5CH DISCRT

CONNECTIONS

CAUTION

Before attempting to make any connections to or from this unit, be sure to first switch OFF the power to this

unit and to any other components to which connections are being made.

CONNECTIONS WITH OTHER COMPONENTS

When making connections between this unit and other components, be sure all connections are made correctly,

that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each

component to be connected to this unit.

* If you have YAMAHA audio/video unit numbered as

etc. on the rear panel, connections can be made

easily by making sure to connect the output ( or input) terminals of each unit to the same-numbered terminals of

this unit.

TAPE 1

TAPE

REC

OUT

TAPE 2

TAPE

REC

OUT

10dB

0dB

PHONO

LD/TV

VCR 1

VCR 2

OUT

VIDEO SIGNAL

AUDIO SIGNAL

MONITOR

OUT

S VIDEO

AUDIO SIGNAL

LD/TV

VCR 1

VCR 2

OUT

VIDEO

ANT

GND

ANT

GND

Ω

UNBAL.

FRONT

LEVEL

FRONT

OUT

LD/TV

CENTER

LD/TV

SURROUND

5CH

DISCRT

INPUT

LD/TV

MAIN

Monitor TV

Tape deck 1

Turntable

Video cassette recorder 1

Video cassette recorder 2

Compact disc player

GND

VIDEO IN

Tape deck 2

LD Player

VIDEO IN

AUDIO IN

VIDEO OUT

AUDIO OUT

VIDEO OUT

AUDIO OUT

OUTPUT

AUDIO OUT

VIDEO OUT

VIDEO IN

AUDIO IN

LINE IN

LINE OUT

LINE IN

LINE OUT

ENGLISH

CONNECTING SPEAKERS

Connect the respective speakers to this unit as shown below:

VIDEO SIGNAL

MONITOR

OUT

S VIDEO

LD/TV

VCR 1

VCR 2

OUT

A OR B: 5

Ω

MIN. /SPEAKER

B: l2

Ω

MIN. /SPEAKER

OUTPUT

REAR OUT

CENTER

OUT

LOW

PASS

fo:200Hz

Ω

MIN. /SPEAKER

SPEAKERS

REAR

FRONT

CENTER

C: 8

Ω

MIN. /SPEAKER

D: 4

Ω

MIN. /SPEAKER

Right Left

Front speakers A

Rear speakers

Right Left

Front speakers B

Center speaker(s)

Note on front speaker connection:

One or two speaker systems can be connected to this

unit. If you connect only one speaker system, connect

it to either the SPEAKERS A or B terminals.

Note on center speaker connection:

One or two center speakers can be connected to this

unit. If you cannot place the center speaker on or

under the TV, it is recommended to use two center

speakers and place them on both sides of the TV to

orient the center sound at the center position.

When connecting two center speakers, be sure to

press the CENTER speaker switch into the “C+D”

position( ). When you use a single center speaker, set

the switch to the “C” position ( ).

How to Connect:

Connect the SPEAKERS terminals to your speakers

with wire of the proper gauge, cut as short as pos-

sible. If the connections are faulty, no sound will be

heard from the speakers. Make sure that the polarity

of the speaker wires is correct, that is, + and – mark-

ings are observed. If these wires are reversed, the

sound will be unnatural and will lack bass.

CAUTION

Do not let the bare speaker wires touch each other and

do not let them touch the metal parts of this unit. This

could damage this unit and/or the speakers.

Note:

Use speakers with the specified impedance shown on

the rear of this unit.

For connecting to the SPEAKER terminals

Red: positive (+)

Black: negative (–)

1 Unscrew the knob.

2 Insert the bare wire.

[Remove approx. 5mm

(1/4”) insulation from

the speaker wires.]

3 Tighten the knob and

secure the wire.

Banana Plug connections are also possible. Simply insert

the Banana Plug connector into the corresponding termi-

nal. (Not available on Singapore model.)

Note:

Use only single type banana plug cable.

ABOUT THE ACCESSORY TERMINALS

OUTPUT

REAR OUT

CENTER

OUT

LOW

PASS

fo:200Hz

1 LOW PASS terminal

This terminal is for output to a monaural amplifier

driving a subwoofer. Frequencies above 200␣ Hz are

filtered out so that only the bass range remains.

The output signal is from the front and center

channels.

You may wish to add a subwoofer to reinforce the

bass frequencies.

Connect the LOW PASS terminal to the INPUT

terminal of the subwoofer amplifier, and connect

the speaker terminals of the subwoofer amplifier to

the subwoofer.

With some subwoofers, including the Yamaha

Active Servo Processing Subwoofer System, the

amplifier and subwoofer are in the same unit.

2 CENTER OUTPUT terminal

This terminal is for center channel line output.

There is no connection to this terminal when you

use the built-in amplifier.

However, if you drive a center speaker with an

external power amplifier, connect the input

terminal of the external amplifier to this terminal.

3 REAR OUTPUT terminals

These terminals are for rear channel line output.

There is no connection to these terminals when

you use the built-in amplifier.

However, if you drive rear speakers with an

external stereo power amplifier, connect the input

terminals of the external amplifier (MAIN IN or

AUX terminals of a power amplifier or an inte-

grated amplifier) to these terminals.

GND terminal (For turntable use)

Connecting the ground wire of the turn-

table to this terminal will normally

minimize hum. In some cases, better

results may be obtained with the ground

wire disconnected.

AC OUTLETS

2 SWITCHED OUTLETS and 1

UNSWITCHED OUTLET (USA,

Canada models)

Use these to connect the power

cords from your components to

this unit.

The power to the SWITCHED outlets is controlled by

this unit’s POWER switch or the provided remote

control transmitter’s POWER key. These outlets will

supply power to any connected component whenever

this unit is turned on.

SWITCHED UNSWITCHED

120V 60Hz

120W MAX. TOTAL

120V 60Hz

200W MAX.

(USA model)

GND

The maximum power (total power consumption of

components) that can be connected to the SWITCHED

AC OUTLET(S) is 120 watts.

The power to the UNSWITCHED outlets cannot be

controlled by this unit’s POWER switch or the

provided remote control transmitter’s POWER key.

(USA, Canada models only).

The maximum power (power consumption of compo-

nent) that can be connected to the UNSWITCHED AC

OUTLET is 200 watts (USA model), 180 watts

(Canada model).

ENGLISH

10dB

0dB

TAPE 2

FRONT

LEVEL

FRONT

OUT

LD/TV

CENTER

LD/TV

SURROUND

5CH

DISCRT

INPUT

LD/TV

MAIN

TAPE 2

REC

OUT

75CH DISCRT INPUT terminals

These terminals are used with a Dolby Surround

AC-3 decoder. Connect the main audio output of

the decoder to the LD/TV MAIN input terminals,

the center channel audio output to the LD/TV

CENTER input terminal, and the surround audio

output to the LD/TV SURROUND input termi-

nals.

Note:

The 5CH DISCRT INPUT terminals are for used with an

AC-3 decoder.

When you use a Dolby Surround AC-3 decoder, the LFE

(Low Frequency Effect channel) signal coming from the

AC-3 decoder to this unit must be mixed with the main

output signal. Refer to your AC-3 decoder’s operating

manual for information about mixing these signals mode.

4 FRONT CH — MAIN␣ IN terminals

These terminals are for line input to the built-in

front channel amplifier. Leave the jumper bars

connected to the PRE␣ OUT terminals when you use

the built-in amplifier.

However, if you drive front speakers with an

external stereo power amplifier, remove the

jumper bars.

5 FRONT␣ CH — PRE␣ OUT terminals

These terminals are for front main channel line

output. Leave the jumper bars connected to the

MAIN␣ IN terminals when you use the built-in

amplifier.

However, if you drive front speakers with an

external stereo power amplifier, remove the

jumper bars and connect the input terminals of the

external amplifier (MAIN IN or AUX terminals of

a power amplifier or an integrated amplifier) to

these terminals.

6 FRONT LEVEL switch

Normally set to “0␣ dB”. If desired, you can de-

crease the output level at the FRONT SPEAKERS

terminals by 10␣ dB by setting this switch to

“–10␣ dB”.

CONNECTING S␣ VIDEO TERMINALS

If your video cassette recorder, video disc player, monitor, etc., are equipped with “S” (high-resolution) video

terminals, connect them to this unit’s S␣ VIDEO terminals. Otherwise, use the composite video terminals of the unit.

Note:

• If video signals are sent to both the S␣ VIDEO input and composite input terminals, the input signals will be sent to the

respective S␣ VIDEO output and composite output terminals independently.

VIDEO SIGNAL

MONITOR

OUT

S VIDEO

LD/TV

VCR 1

VCR 2

OUT

VIDEO

Video Cassette recorder 2

Video Cassette recorder 1

LD player

VIDEO

OUT

S VIDEO

OUT

Monitor TV

VIDEO

S VIDEO

S VIDEO OUT

VIDEO OUT

S VIDEO IN

VIDEO IN

S-VIDEO OUT

VIDEO OUT

S-VIDEO IN

VIDEO IN

ON SCREEN DISPLAY

If you connect a video cassette recorder, video disc player, monitor, etc., to this unit, you can display DSP

program names and information about the other settings and adjustments on the video monitor screen. This

information is superimposed over the video image.

If there is no program material on the monitor, the information will be displayed over a monochromatic back-

ground.

Notes:

• If you use a video monitor that is connected to both the S␣ VIDEO and composite terminals, the screen display informa-

tion is only output from the S␣ VIDEO terminals.

• When no video signal is input to any of the S␣ VIDEO or composite video input terminals, the screen display information

is output from the S␣ VIDEO and composite MONITOR OUT terminals with a monochromatic background.

CONNECTING TO VIDEO AUX TERMINALS (FRONT PANEL)

These terminals are used to connect any video input source such as a camcorder to this unit.

AUDIO OUT

VIDEO OUT

VIDEO

Camcorder

S-VIDEO

S VIDEO OUT

8 VIDEO

VIDEO AUX

8 VIDEO VIDEO L AUDIO R

ENGLISH

ANTENNA CONNECTIONS

• Each antenna should be connected to the designated terminals correctly, referring to the following diagram.

• Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide

sufficient signal strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an

indoor one. If you experience poor reception quality, an outdoor antenna may result in improvement.

TAPE 1

TAPE

REC

OUT

TAPE 2

TAPE

REC

OUT

10dB

0dB

PHONO

AUDIO SIGNAL

ANT

GND

ANT

GND

Ω

UNBAL.

FRONT

LEVEL

FRONT

OUT

AM loop

antenna

(included)

Indoor FM

antenna

(included)

Ground

Outdoor AM antenna

Outdoor FM antenna

75-ohm/300-ohm

antenna adapter

75-ohm

coaxial cable

300-ohm

feeder

Connecting the AM loop antenna

123

• The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall.

• The AM loop antenna should be kept connected, even if an outdoor AM antenna is connected to this unit.

➀

➁

➂

GND terminal

For maximum safety and minimum interference,

connect the GND terminal to a good earth ground.

A good earth ground is a metal stake driven into

moist earth.

Notes:

• When connecting the indoor FM

antenna, insert its connector into the

FM ANT terminal firmly.

• If you need an outdoor FM antenna to

improve FM reception quality, either

300-ohm feeder or coaxial cable may be

used. In locations troubled by electrical

interference, coaxial cable is preferable.

Orient so that the best

reception is obtained.

ADJUSTMENT BEFORE OPERATION

SPEAKER BALANCE ADJUSTMENT

This procedure lets you adjust the sound output level balance between the front, center, and rear speakers using

the built-in test tone generator. With this adjustment, the sound output level heard at the listening position will be

the same from each speaker. This is important for the best performance of the digital sound field processor.

The adjustment of each speaker output level should be done at your listening position with the remote control

transmitter. Otherwise, the result may not be satisfactory.

234

POWER

PLAY

TAPE 1

DIR A DIR B

SKIP

PHONO

TUNER

STOP PLAY

SLEEP TV VCR AUX

DISC

SKIP

PAUSE/STOP

DECK

A/B

PRESET

A B C D E

REC/PAUSEREC MUTE TAPE 2 MON

PLAY LD/TV

TRANSMIT

/LEARN

YPC LEARN

USER

—

* If you have a video monitor connected to this unit, you should use it to display the on screen information. The

easy-to-read information will help you to perform this adjustment.

Note:

Before adjustment, make sure that the mute circuit is not engaged. While mute is engaged, no sound will be heard and an

indicator on the master VOLUME control flashes. See page 23 for details.

Set to the “

∞

” position.

Set the remote YPC-USER-LEARN switch to the “YPC”

position.

For detailed information about the remote control transmitter,

refer to “REMOTE CONTROL TRANSMITTER” on page 34.

Set to the “0” position.

BASS TREBLE

YPC LEARN

USER

VOLUME

–dB

POWER

Press the POWER

switch to turn on the

power.

Select the main speakers to be used.

• If you use two main speaker systems, press both the A and

B switches.

SPEAKERS

BALANCE

Set to the “0” position.

ENGLISH

STOP

VCR 1

VCR 2

V–AUX

CHAPTER/CH

—

DISPLAY

MASTER

VOLUME

—

TEST

MUTING

—

DSP

HALL

EFFECT

CHURCH

CENTER LEVEL

REAR LEVEL

DELAY

TIME

MOVIE THEATER

JAZZ CLUB

STADIUM

PRO LOGIC

SURROUND

SPORTS

ENHANCED

ROCK

THEATER

70mm TV

1234

5678

910

ON/OFF

RESET CLEAR

In step 7, when you select the center mode, note the

following.

Five speaker configuration

NORMAL: Select this mode when you use a

center speaker that is smaller than the

front main speakers. In this mode, the

bass tone will be output from the

front speakers.

WIDE: Select this mode when your center

speakers are approximately the same

size as the front speakers.

Four speaker configuration

PHANTOM: Select this mode when you do not

have a center speaker. The center

channel sound will be output from

the left and right font speakers.

—

Select the center channel output mode according to your

speaker configuration.

(Refer to “SPEAKER CONFIGURATION” on page 8.)

CENTER

MODE

NORMAL

WIDE

PHANTOM

• If your video monitor is on, the state of the test tone output

is also shown by an image of an audio listening room on the

screen.

• The test tone from the left rear speaker and the right rear

speaker will be heard at the same time.

Turn up the volume using the remote

control transmitter.

You will hear a test tone (like pink

noise) from the left front speaker, then

the center speaker, then the right front

speaker, and then the rear speakers, for

about two seconds each. The display

changes as shown below.

TEST

MASTER

VOLUME

Press the TEST button to run the Dolby

test.

STOP

VCR 1

VCR 2

V–AUX

CHAPTER/CH

—

DISPLAY

MASTER

VOLUME

—

TEST

MUTING

—

DSP

HALL

EFFECT

CHURCH

CENTER LEVEL

REAR LEVEL

DELAY

TIME

MOVIE THEATER

JAZZ CLUB

STADIUM

PRO LOGIC

SURROUND

SPORTS

ENHANCED

ROCK

THEATER

70mm TV

1234

5678

910

ON/OFF

RESET CLEAR

Notes:

• Once you have completed these adjustments, you can

adjust whole sound level on your audio system by using

the VOLUME control (or the MASTER VOLUME keys

on the remote control transmitter).

• If you use external power amplifiers, their volume

controls may also need to be adjusted to achieve the

proper balance.

If there is insufficient sound output from the center

and rear speakers, you may decrease the front speaker

output level by setting the FRONT LEVEL switch on

the rear panel to “–10 dB”.

Note:

• If the center channel mode is in the “PHANTOM”

position, the sound output level of the center speaker

cannot be adjusted. This is because in this mode, the

center sound is automatically output from the left and

right front speakers.

• If you press the LEVEL +/– switch without previously

pressing the CENTER, or REAR switch, the last

channel selected will be changed.

Adjust the BALANCE control so that the test tone sound

output level of the left front speaker and the right front

speaker are the same.

Adjust the sound output level of the rear speakers to be

at the same level as that of the front speakers with the

REAR LEVEL keys.

Adjust the test tone sound output level of the center

speaker to be at the same level as that of the front

speakers with the CENTER LEVEL keys.

Cancel the test tone.

BALANCE

TEST

CENTER

LEVEL

REAR

LEVEL

PRO LOGIC

The previous mode is selected.

La pagina sta caricando ...

Yamaha RX-V990 Manuale utente

Marca: Yamaha

Modello: RX-V990

Categoria: Lettori di cassette

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: Yamaha RX-V990 User manual
français: Yamaha RX-V990 Manuel utilisateur
español: Yamaha RX-V990 Manual de usuario
Deutsch: Yamaha RX-V990 Benutzerhandbuch
русский: Yamaha RX-V990 Руководство пользователя
Nederlands: Yamaha RX-V990 Handleiding
português: Yamaha RX-V990 Manual do usuário
dansk: Yamaha RX-V990 Brugermanual
čeština: Yamaha RX-V990 Uživatelský manuál
polski: Yamaha RX-V990 Instrukcja obsługi
svenska: Yamaha RX-V990 Användarmanual
Türkçe: Yamaha RX-V990 Kullanım kılavuzu
suomi: Yamaha RX-V990 Ohjekirja
română: Yamaha RX-V990 Manual de utilizare

Documenti correlati

Altri documenti

Renkforce E-SA9 Manuale del proprietario