Dometic PerfectView M7LS Istruzioni per l'uso

M7LS

LCD-Monitor

Installation and Operating Manual . . . . . 11

LCD-Monitor

Montage- und Bedienungsanleitung . . . 25

Ecran LCD

Instructions de montage

et de service . . . . . . . . . . . . . . . . . . . . . . . 39

Pantalla LCD

Instrucciones de montaje y de uso . . . . .53

Monitor LCD

Instruções de montagem e manual de

instruções . . . . . . . . . . . . . . . . . . . . . . . . . 68

Monitor LCD

Istruzioni di montaggio e d’uso . . . . . . . . 82

LCD-monitor

Montagehandleiding en

gebruiksaanwijzing . . . . . . . . . . . . . . . . . 96

LCD-monitor

Monterings- og betjeningsvejledning . . 111

LCD-monitor

Monterings- och bruksanvisning. . . . . . 124

LCD-monitor

Monterings- og bruksanvisning . . . . . . 137

LCD-monitori

Asennus- ja käyttöohje. . . . . . . . . . . . . . 150

ЖК-монитор

Инструкция по монтажу

и эксплуатации. . . . . . . . . . . . . . . . . . . . 163

Monitor LCD

Instrukcja montażu i obsługi . . . . . . . . . 177

LCD monitor

Návod na montáž a uvedenie

do prevádzky . . . . . . . . . . . . . . . . . . . . . .191

Monitor LCD

Návod k montáži a obsluze . . . . . . . . . . 203

LCD-monitor

Szerelési és használati útmutató . . . . . . 216

C1/C2

MENU

POWER

+

EN

DE

FR

ES

PT

IT

NL

DA

SV

NO

FI

RU

PL

SK

CS

HU

DRIVING SUPPORT

PERFECTVIEW

M7LS-MB-16s.book Seite 1 Mittwoch, 3. August 2016 8:10 08

M7LS-MB-16s.book Seite 2 Mittwoch, 3. August 2016 8:10 08

M7LS

3

1

4

8

12 13 14

911

56 7

23

10

1

M7LS-MB-16s.book Seite 3 Mittwoch, 3. August 2016 8:10 08

M7LS

4

2

3

4

5

M7LS-MB-16s.book Seite 4 Mittwoch, 3. August 2016 8:10 08

M7LS

5

B

A

D

C

6

A

10 mm

15 mm

B

C

D

7

A

10 mm

B

20 mm

C

D

8

M7LS-MB-16s.book Seite 5 Mittwoch, 3. August 2016 8:10 08

M7LS

6

A

B

9

0

a

M7LS-MB-16s.book Seite 6 Mittwoch, 3. August 2016 8:10 08

M7LS

7

b

M7LS-MB-16s.book Seite 7 Mittwoch, 3. August 2016 8:10 08

M7LS

8

C1/C2

MENU

POWER

+

1

3

2

c

C1/C2 MENU POWER

+

123

46

5

d

M7LS-MB-16s.book Seite 8 Mittwoch, 3. August 2016 8:10 08

M7LS

9

1

3

2

4

e

M7LS-MB-16s.book Seite 9 Mittwoch, 3. August 2016 8:10 08

M7LS

10

1 32

7

6

11

12

13

10

9

5

8

4

C1 C2

f

M7LS-MB-16s.book Seite 10 Mittwoch, 3. August 2016 8:10 08

M7LS Notes on using the operating manual

EN

11

Please read this instruction manual carefully before installation and first use, and store

it in a safe place. If you pass on the product to another person, hand over this instruc-

tion manual along with it.

Contents

1 Notes on using the operating manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2 Safety and installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

5 Technical description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

6 General information on the electrical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

7 Mounting the monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

8 Using the LCD-monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

9 Cleaning and maintaining the LCD monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

10 Guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

11 Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

12 Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

1 Notes on using the operating manual

!

A

I

CAUTION!

Safety instruction: Failure to observe this instruction can lead to injury.

NOTICE!

Failure to observe this instruction can cause material damage and impair the function

of the product.

NOTE

Supplementary information for operating the product.

M7LS-MB-16s.book Seite 11 Mittwoch, 3. August 2016 8:10 08

Safety and installation instructions M7LS

EN

12

2 Safety and installation instructions

Please observe the prescribed safety instructions and stipulations from the vehicle

manufacturer and service workshops.

The manufacturer accepts no liability for damage in the following cases:

• Faulty assembly or connection

• Damage to the product resulting from mechanical influences and excess voltage

• Alterations to the product without express permission from the manufacturer

• Use for purposes other than those described in the operating manual

A

Therefore, please observe the following instructions:

• When working on the following cables, only use insulated cable terminals, plugs and flat sock-

ets:

– 30 (direct supply from positive battery terminal)

–15 (connected positive terminal, behind the battery)

– 31 (return cable from the battery, earth)

–Reversing light

Do not use porcelain wire connectors.

• Use a crimping tool (fig. 1 12, page 3) to connect the cables.

• Screw the cable when connecting cable 31 (earth)

– Screw on the cable using a cable terminal and serrated washer to one of the vehicle's earth

bolts or

– Screw the cable to the bodywork using a cable terminal and a self-tapping screw

Make sure there is a good earth connection.

NOTICE! Beware of damage

• To prevent the risk of short circuits, always disconnect the negative terminal of the

vehicle's electrical system before working on it.

If the vehicle has an additional battery, its negative terminal should also be discon-

nected.

• Inadequate supply cable connections could result in short circuits, causing:

–Cable fires

– The airbag being triggered

– Damage to electronic control equipment

– Electrical malfunctions (indicators, brake light, horn, ignition, lights)

M7LS-MB-16s.book Seite 12 Mittwoch, 3. August 2016 8:10 08

M7LS Safety and installation instructions

EN

13

If you disconnect the negative terminal of the battery, all data stored in the volatile memories will

be lost.

• The following data must be reset, depending on the vehicle equipment options:

–Radio code

– Vehicle clock

–Timer

– On-board computer

– Seat position

You can find instructions for making these settings in the operating manual.

Observe the following installation instructions:

!

Observe the following instructions when working with electrical parts:

• When testing the voltage in electrical cables, only use a diode test lamp (fig. 1 1, page 3) or a

voltmeter (fig. 1 2, page 3).

Test lamps with a bulb (fig. 1 3, page 3) consume excessive current which can damage the

vehicle's electronic system.

• When making electrical connections, ensure that:

– they are not kinked or twisted

– they do not rub on edges

– they are not laid in sharp-edged ducts without protection (fig. 3, page 4).

• Insulate all connections.

• Secure the cables against mechanical wear by using cable binders or insulating tape, for exam-

ple on existing cables.

Observe the following instructions when handling the LCD monitor:

!

CAUTION!

• Secure the monitor in such a way that it cannot become loose under any

circumstances (sudden braking, accidents) and cause injuries to the occupants

of the vehicle.

• Do not attach the monitor in the air bag deployment path, as this could cause injury

if the airbags are triggered.

CAUTION!

• People (including children) whose physical, sensory or mental capacities or lack of

experience or knowledge prevent them from using this product safely should not

use it without the supervision or instruction of a responsible person.

• Do not open the monitor (fig. 4, page 4).

• Do not immerse the monitor in water (fig. 5, page 4); the monitor is not water-

proof.

• The monitor must not impair your vision when driving (fig. b, page 7).

• Do not operate the monitor with wet hands.

• Do not operate the monitor if the housing has been damaged.

M7LS-MB-16s.book Seite 13 Mittwoch, 3. August 2016 8:10 08

Scope of delivery M7LS

EN

14

A

3Scope of delivery

4Intended use

The M7LS LCD monitor (item no. 9600000204) is a monitor primarily intended for use in vehicles.

It can be used to connect cameras (e. g. a reversing video system) or other video sources.

The LCD monitor is designed for use in all vehicles.

Since rear view systems are designed merely as an additional aid for reversing, it does not relieve

you of the duty to take proper care when reversing.

NOTICE!

• Connect it to the correct voltage.

• Do not use the monitor in areas which

– Are subjected to direct sunlight,

– Are subject to strong temperature fluctuations,

– Have high levels of humidity,

– Are poorly ventilated,

– Are dusty or oily.

• Do not press against the LCD display.

• Do not drop the monitor.

• If you use the monitor in vehicles, the vehicle should be running during operation to

prevent the vehicle battery from discharging.

• The picture quality can be impaired in the vicinity of electromagnetic fields.

For this reason do not mount the monitor near loudspeakers.

No. in

fig. c,

page 8

Quantity Description

Reference

number

1 1 Monitor M7LS 9600000204

21Monitor bracket

3 1 Connection cable 9102200027

––Fastening material

M7LS-MB-16s.book Seite 14 Mittwoch, 3. August 2016 8:10 08

M7LS Technical description

EN

15

5 Technical description

5.1 Function description

The LCD monitor is a monitor which allows cameras (e. g. a rear view video camera) or other video

sources (e. g. a TV) to be connected. It is possible to switch back and forth between video sources.

The monitor can be mounted on the dashboard, where it transmits the image from the connected

camera, allowing the driver to see the area behind the vehicle, e. g. when parking.

The brightness of the monitor adapts automatically to the ambient light.

The buttons are illuminated and can therefore also be operated in the dark.

The mirrored picture function can be activated individually for each of the two video inputs. The

image then appears as if you were looking into the rear view mirror.

5.2 Operating elements

The following control elements are located on the monitor:

No. in

fig. d,

page 8

Designation Description

1Light sensor

2 C1/C2 Selects the camera or swaps menu page 1 and 2.

3 – Reduces the volume or other selected parameters (bright-

ness, contrast, colour tint).

4 MENU Switches to setup mode (see chapter “Using the LCD-moni-

tor” on page 21).

5 + Increases the volume or other selected parameters (bright-

ness, contrast, colour tint).

6 Switches the monitor on and off.

M7LS-MB-16s.book Seite 15 Mittwoch, 3. August 2016 8:10 08

General information on the electrical connections M7LS

EN

16

6 General information on the electrical connections

6.1 Laying cables

A

Please observe the following instructions:

• As far as possible, use original openings or alternative openings for the connecting cable duct,

e. g. the paneling edges, ventilation grilles or blank panels. If no openings are available, you

must drill holes for the cables. Check beforehand that there is sufficient space on the other side

for the drill head to come out.

• Wherever possible lay cables inside the vehicle, as they are better protected there than outside

the vehicle.

If you do need to lay a cable outside the vehicle, ensure that it is well secured (use additional

cable ties, insulating tape, etc.).

• To prevent damage to the cables, when laying them, ensure that they are far enough away from

hot or moving vehicle components (exhaust pipes, drive shafts, light systems, fans, heater etc.).

• Wrap insulating tape around the plug connections of the connecting cables and every connec-

tion on a cable (including inside the vehicle) to protect them from exposure to water (fig. 9,

page 6). The most suitable tape for this purpose is self-vulcanising tape, for example from 3M.

• When laying electric connections (fig. 3, page 4), ensure that

– They are not kinked or twisted

– They do not rub on edges

– They are not laid in sharp edged ducts without protection

• Attach the cables securely in the vehicles to prevent tripping hazards. Use cable binders, insu-

lating tape or glue the cables in place.

• Protect every through-hole made in the bodywork against water penetration, e. g. by using a

cable with a sealant and by spraying the cable and the the cable sleeve with sealant.

I

NOTICE!

Cables and connections which are not properly installed will cause malfunctions or

damage to components. Correct installation of cables and connections ensures lasting

and trouble-free operation of the retrofitted components.

NOTE

Do not start sealing the through-holes until you have completed all installation work on

the camera, and the required cable lengths have been laid.

M7LS-MB-16s.book Seite 16 Mittwoch, 3. August 2016 8:10 08

M7LS Mounting the monitor

EN

17

6.2 Using branch connectors (fig. 6, page 5)

To prevent loose connections in the branch connectors, it is important to ensure that the cable

cross sections fit into the branch connectors.

To use the branch connectors, proceed as follows:

➤ Insert the cable to be tapped in the front groove of the cable connector (A).

➤ Insert the end of the new cable up to approx. 3/4 of the way into the rear groove (B).

➤ Use a pair of combination pliers to close the connector by pressing the metal pin in. This cre-

ates an electrical connection (C).

➤ Press down the safety cap until it snaps into place.

➤ Check that the connection is secure by lightly tugging the cable (D).

6.3 Creating clean soldering joints

Proceed as follows to solder a cable to the original cables (fig. 7, page 5):

➤ Strip approx. 10 mm of insulation from the end of the original cable (A).

➤ Strip approx. 15 mm of insulation from the end of the cable to be connected (B).

➤ Wind the cable to be connected around the original cable and solder the two cables together

(C).

➤ Insulate the two cables with insulating tape (D).

Proceed as follows to solder two cables together (fig. 8, page 5):

➤ Strip the two cables (A).

➤ Place a shrink sleeve with a length of approx. 20 mm over the cable (B).

➤ Twist the cables together and solder them (C).

➤ Place a shrink sleeve over the soldered point and heat it briefly (D).

7 Mounting the monitor

7.1 Tools required (fig. 1, page 3)

For installation and assembly you will need the following tools:

• Measuring ruler (4)

• Centre punch (5)

• Hammer (6)

• Drill bit set (7)

• Drill (8)

• Screwdriver (9)

M7LS-MB-16s.book Seite 17 Mittwoch, 3. August 2016 8:10 08

Mounting the monitor M7LS

EN

18

To make and test the electrical connection, the following tools are required:

• Diode test lamp (1) or voltmeter (2)

• Insulating tape (10)

• Heat shrinking sleeve

• Hot air blower (11)

• Crimping tool (12)

• Soldering iron (optional) (13)

• Solder (optional) (14)

• Cable bushing sleeves (optional)

Depending on the individual installation requirements you may require bolts, nuts, washers, self-

tapping screws and cable binders other than those including in the scope of delivery.

7.2 Installing the monitor

!

Observe the following installation instructions:

• Select an installation location that provides an unobstructed view of the monitor (fig. 0,

page 6 and fig. a, page 6).

• Never install the monitor in area where your head could impact it or in the air bag deployment

path. This could cause injury if the airbag opens.

• The monitor must not impair your vision when driving (fig. b, page 7).

• The installation location should be flat.

• Check that there is sufficient space underneath the installation location to attach the washers

and nuts.

• Check beforehand that there is sufficient space on the other side for the drill head to come out.

• Bear in mind the weight of the monitor. Provide reinforcement if necessary (larger washers or

plates).

• Ensure that you can lay the connection cable set to the monitor.

CAUTION! Risk of injury!

Select the location of the monitor so that it cannot injure the passengers in the vehicle

under any circumstances (e. g. sudden braking, road traffic accidents).

M7LS-MB-16s.book Seite 18 Mittwoch, 3. August 2016 8:10 08

M7LS Mounting the monitor

EN

19

To perform the installation, proceed as follows (fig. e, page 9):

➤ Slide the monitor (1) onto the mounting plate of the monitor bracket (2) and secure it on the

monitor bracket with the knurled screw (3).

➤ Position the monitor and the attached monitor bracket for testing.

➤ Mark the outlines of the corners of the monitor bracket (2) on the dashboard.

➤ Unscrew the monitor from the monitor holder.

➤ Hold the monitor bracket within the outlines marked beforehand and mark four different drill-

ing points.

➤ Drill Ø 2 mm holes at the points you have just marked.

➤ Screw on the monitor bracket with the 4 x 20 mm self-tapping screws.

➤ Slide the monitor (1) onto the mounting plate of the monitor bracket (2) and secure it on the

monitor bracket with the knurled screw (3).

I

7.3 Laying the system cable from the camera to the monitor

I

➤ Lay the system cable for the camera inside the vehicle.

➤ Lay the system cable for the camera to the monitor.

➤ Connect the monitor connection cable to the system cable.

➤ Insulate the plug connection with the insulating tape supplied. Overlap every layer of the insu-

lating tape by one half of its width.

➤ Attach the cables securely in the vehicles to prevent tripping hazards. This can be performed

by using cable binders, insulating tape or gluing in place with adhesives.

I

NOTE

You can now adjust the angle of inclination. To do this, loosen the knurled screw (4)

and tilt the monitor to the desired position. Tighten the knurled screw (4).

NOTE

Lay the camera cable so that should you need to remove the camera, you can access

the plug connection between the camera and the extension cable easily. This greatly

facilitates the disassembly.

NOTE

Only start sealing through-holes when you have completed all installation work on the

camera and have laid the required cable lengths.

M7LS-MB-16s.book Seite 19 Mittwoch, 3. August 2016 8:10 08

Mounting the monitor M7LS

EN

20

7.4 Connecting the monitor to an electricity supply (fig. f, page 10)

The circuit diagram for the monitor can be found in fig. f, page 10.

Observe the following instructions when laying the connection cable:

• Feed the connection cable through existing ducts or other openings where possible e. g. ven-

tilation grilles. If no appropriate ducts or openings are available you will need to drill a hole of

 18 mm. Check beforehand that there is sufficient space on the other side for the drill head to

come out (fig. 2, page 4).

• Please observe the notes from the chapter “General information on the electrical connections”

on page 16.

➤ Lay the monitor cable on the dashboard.

➤ Insert the plug of the monitor cable (2) in the socket (4) of the connection cable (3).

A

➤ Connect the red and black cables of the connection cables to a suitable voltage source:

– Connect the red cable (5) to terminal 15 (ignition).

– Connect the black cable (6) to terminal 31 (earth).

➤ If necessary, connect the mini DIN socket (7) of the connection cable to the mini DIN plug (9)

of the system cable (10).

No. Description

1Monitor

2 13-pin DIN plug

3Connection cable

413-pin DIN socket

5 12 V positive cable (red): Connection to the positive pole of the voltage source

6 Earth cable (black): Connection to the negative pole of the voltage source

76-pin DIN socket

8 Cable (green): Control input for the connection to the reversing lights

96-pin mini DIN plug

10 System cable

11 6-pin mini DIN socket

12 6-pin mini DIN plug

13 Camera

NOTICE!

Make sure the polarity is correct when connecting to a voltage source.

M7LS-MB-16s.book Seite 20 Mittwoch, 3. August 2016 8:10 08

La pagina sta caricando ...

Dometic PerfectView M7LS Istruzioni per l'uso

Questo manuale è adatto anche per

Dometic PerfectView M7LS Istruzioni per l'uso

in altre lingue

Documenti correlati

Altri documenti