Yamaha MFC10 Manuale del proprietario

Marca: Yamaha

Modello: MFC10

Categoria: Pianoforti digitali

Tipo: Manuale del proprietario

Congratulations!

Thank you for purchasing Yamaha’s MFC10 MIDI Foot Controller.

The MFC10 is a versatile MIDI foot control device that can transmit program changes and

control changes to control effectors, tone generators, keyboards, MIDI guitars, rhythm

machines, etc..

In addition to the onboard foot controller, up to 4 optional external foot controllers or

switches can also be connected to the MFC10 for increased control versatility.

In order to make full use of the MFC10’s features and functions, we recommend that you

read this manual thoroughly and keep it in a safe place for future reference.

Contents

Precautions................................................................................................................... 2

Power Supply ............................................................................................................... 3

Nomenclature ............................................................................................................... 4

Functions du MFC10.................................................................................................... 6

2 Modes .....................................................................................................6

Foot Controller Settings ...................................................................................7

All memory MIDI Channel Assign ........................................................................7

Bulk Dump ..................................................................................................7

Normal Mode ................................................................................................................ 8

Program Change Memory .................................................................................9

Program Change Memory Control (Transmit) ..........................................................9

Program Change Memory Edit .........................................................................10

Function Memory...........................................................................................12

Function Memory Control (Transmit) ..................................................................12

Edit Function Memory ...................................................................................13

About the TOGGLE ON-OFF/NUMBER OF PGM settings.................................18

MIX Mode ....................................................................................................................19

MIX Mode Memory Control (Transmit) ................................................................20

Editing MIX mode ........................................................................................21

The MIX mode’s Function Memory ............................................................21

Foot Controller ...........................................................................................................22

Editing FC (Foot Controller) data ......................................................................22

All Memory MIDI Channel Number Assign...............................................................24

Bulk Dump ..................................................................................................................25

Bulk Dump (Transmission) ..............................................................................25

Bulk Dump (Receive) .....................................................................................25

Initialize .......................................................................................................................26

MFC10 Sample Setups...............................................................................................27

MIDI Guitar System........................................................................................27

MIDI Keyboard System ...................................................................................28

MIDI Effector System .....................................................................................28

MIDI Sequencer or Rhythm Programmer System .................................................29

Error Messages ..........................................................................................................30

Trouble Shooting........................................................................................................30

MIDI Implementation Chart ....................................................................................................... 31

MIDI data format ....................................................................................................................... 32

Operation Guide........................................................................................................................ 35

Program Table........................................................................................................................... 36

Specifications ............................................................................................................................ 40

Precautions

!! PLEASE READ THIS BEFORE PROCEEDING !!

■ Location

Do not expose the MFC10 to the following

conditions to avoid deformation, discoloration,

or more serious damage.

• Direct sunlight (e.g. near a window).

• High temperatures (e.g. near a heat source,

outside, or in a car during the daytime).

• Excessive humidity.

• Excessive dust.

• Strong vibration.

■ USE THE CORRECT POWER SUPPLY

• Power to the MFC10 should be supplied

only from the appropriate Yamaha AC

adaptor (the PA-3B or another adaptor

specifically recommended by Yamaha). Use

of another adaptor may cause serious

damage to the unit. Also make sure that the

adaptor you have is appropriate for the AC

mains supply voltage in the area where you

intend to use the MFC10. (The correct

input voltage is marked on the adaptor.)

■ Power Supply

• Turn the power switch OFF when the

instrument is not in use.

• The power adaptor should be unplugged

from the AC outlet if the MFC10 is not to

be used for an extended period of time.

• Unplug the MFC10 during electric storms.

• Avoid plugging the MFC10 into the same

AC outlet as appliances with high power

consumption, such as electric heaters or

ovens. Also avoid using multi-plug adaptors

since these can result in reduced sound

quality and possibly damage.

■ Turn Power OFF When Making Connections

• To avoid damage to the MFC10 and other

devices to which it is connected (a sound

system, for example), turn the power

switches of all related devices OFF prior to

connecting or disconnecting audio and MIDI

cables.

■ MIDI Connections

• When connecting the MFC10 to MIDI

equipment, be sure to use high-quality

cables made especially for MIDI data

transmission.

• Avoid MIDI cables longer than about 15

meters. Longer cables can pick up electrical

noise that can causes data errors.

■ Handling and Transport

• Never apply excessive force to the controls,

connectors or other parts of the instrument.

• Always unplug cables by gripping the plug

firmly, not by pulling on the cable.

• Disconnect all cables before moving the

instrument.

• Physical shocks caused by dropping,

bumping, or placing heavy objects on the

instrument can result in scratches and more

serious damage.

■ Cleaning

• Clean the cabinet and panel with a dry soft

cloth.

• A slightly damp cloth may be used to

remove stubborn grime and dirt.

• Never use cleaners such as alcohol or

thinner.

• Avoid placing vinyl objects on top of the

instrument (vinyl can stick to and discolor

the surface).

■ Electrical Interference

• This instrument contains digital circuitry

and may cause interference if placed too

close to radio or television receivers. If this

occurs, move the instrument further away

from the affected equipment.

■ Data Backup

• The MFC10 contains a special read-write

memory without a battery, that retains the

contents of its internal memory even when

the power is turned OFF.

■ Service and Modification

• The MFC10 contains no user serviceable

parts. Opening it or tampering with it in any

way can lead to irreparable damage and

possibly electric shock. Refer all servicing

to qualified YAMAHA personnel.

YAMAHA is not responsible for damage caused by improper handling or operation.

DC IN

POWER

ON/

OFF

Power Supply

Use the PA-3B power adaptor (or another adaptor recommended by Yamaha) to supply

the MFC10 with power from a convenient wall socket.

Plug the AC adaptor into any convenient AC wall

socket.

Connect the adaptor’s plug into the [DC IN] jack on the

rear panel.

Wrap the power cord around the cord stopper hook to

prevent accidental unplugging during use.

Cord Stopper

Wall Socket

Power Adaptor

• Do not use an AC adaptor other than the

PA-3B, or other adoptors recommended by

Yamaha. The use of any incompatible adaptor

may result in damage, overheating, or fire to

the unit.

• Be sure to disconnected the power adaptor

from the outlet when the MFC10 is not in use.

Nomenclature

Front Panel

STATUS

DATA/CTRL

BANK MSB/MAX

BANK LSB/MIN

TOGGLE ON-OFF

/NUMBER OF PGM

DEC

/NO

INC

/YES

MEMORY

EDIT

WRITE

/EXIT

±10

8.8.8

4 3 5 6

POWER

ON/ OFF DC IN

FOOT

5432 OUTINWX IN

CONTROLLER/SWITCH MIDI

FOOT CONTROLLER 1

1 Parameter Lamp (see page 11, 16)

The currently selected parameter lamp will flash when

in the edit mode.

2 LED Display (see page 6)

Memory numbers, program changes and functions

(control changes) saved in memory, parameters, etc.,

are indicated in the display.

3 [INC/YES] (see page 11, 17)

Increases (INC) edit number values in the Play mode

and parameter data values in the Edit mode, and to

save data that has been edited, the YES button is used

to confirm the save operation.

4 [DEC/NO] (see page 11, 17)

Decreases (DEC) edit number values in the Play mode

and parameter data values in the Edit mode, and when

confirmation of the save operation of edited data is

requested, the NO button cancels the save operation.

5 [MEMORY EDIT] (see page 11, 16)

Enters the Memory Edit mode and selects edit param-

eters.

6 [FC EDIT] (see page 22)

Enters the Foot Controller Edit mode and selects edit

parameters.

7 [WRITE/EXIT] (see page 11, 17)

Exits the Edit mode and returns to the Normal control

mode. At this time it is necessary to press the [INC/

YES] button or [DEC/NO] button to either confirm or

cancel the data overwrite operation.

8 [FUNCTION] Foot switch (see page 6)

Switches between Program Change Memory and

Function Memory when in the Normal Mode.

In the Mix Mode, switches between Mix mode and

Function Memory.

■ Front Panel

Rear Panel

* When the lamp above the [FUNCTION] foot switch

is lit, the MFC10 is in Function Memory.

MIDI WX NORMAL — MIX

FUNCTION

# @

9 [1]-[0] Foot switch (see page 9, 12)

Selects Memory Numbers.

0 [x10] Foot switch (see page 9, 12)

Select the 100's or 10's digit.

! Onboard Foot Controller (see page 22)

The Foot Controller can be used to transmit control

changes, after touch, pitch bend, etc., to external MIDI

devices.

Nomenclature

■ Rear Panel

@ [FUNCTION NORMAL — MIX] Switch

(see page 8, 19)

Selects the mode that the MFC10 is to be operated in,

Normal mode or Mix mode.

# [MIDI — WX] Switch

Selects whether MIDI data is received via the WX jack

or the MIDI IN jack.

$ [WX IN] Jack

A Yamaha Wind MIDI Controller WX7/11 can be

directly connected to this jack. (The MFC10 supplies

electric power to the WX7/11, so the BT-7 Power Box is

not needed.)

% [MIDI IN/OUT] Jacks (see page 27)

Using a MIDI cable, external MIDI devices can be

connect to the MFC10.

^ [FOOT CONTROLLER/SWITCH 2-5] Jacks

(see page 22)

These jacks allow the connection of up to 4 optional

foot controllers or foot switches to the MFC10. The

connected foot controllers or foot switches can be used

to control MIDI data in the same manner as the

onboard foot controller.

& [DC IN] Jack (see page 3)

Connect the power adaptor here to supply the MFC10

with power.

* [POWER ON/OFF] Switch (see page 8)

Turns the MFC10’s power on or off.

User Memo Sticker

The supplied User Memo Sticker can be applied

next to the number plate above each foot switch to

write memos on.

MFC10 Functions

When a foot switch is pressed, MIDI data (program changes/function data) stored in the

MFC10’s internal memory is transmitted to external MIDI devices.

• Program Change Data Program change data transmitted from the MFC10 can select

voices, etc., on other MIDI devices.

Bank select data can be transmitted along with program change

data as well.

• Function Data The MFC10 can transmit the following function data to control

other MIDI devices.

* Values in parentheses are shown in the display.

• NOTE ON/OFF (90-9F)

• CONTROL CHANGE (b0-bF)

• PROGRAM CHANGE (C0-CF)

• SONG SELECT (F3)

• START (FA)

• CONTINUE (Fb)

• STOP (FC)

• SECTION CONTROL (F0)

• TEMPO CONTROL (Ft)

■ 2 Modes................................................................................................

Switch

STATUS

DATA/CTRL

BANK MSB/MAX

BANK LSB/MIN

TOGGLE ON-OFF

/NUMBER OF PGM

DEC

/NO

INC

/YES

MEMORY

EDIT

WRITE

/EXIT

±10

STATUS

DATA/CTRL

BANK MSB/MAX

BANK LSB/MIN

TOGGLE ON-OFF

/NUMBER OF PGM

DEC

/NO

INC

/YES

MEMORY

EDIT

WRITE

/EXIT

±10

The MFC10’s foot switches can be set to operate in one of two modes (Normal Mode/Mix Mode). Use the

[FUNCTION NORMAL — MIX] switch on the rear panel to set the mode the MFC10 will operate in. (see

page 5, 8, 19)

How the foot switches operate in each mode is further explained below.

[In this mode, Program Change Memory and Function Memory are independent of each other.]

NORMAL — MIX

FUNCTION

• NORMAL mode

Function memory

(100 types)

Program change memory

(128 types)

Function lamp is lit

Function lamp is off

MFC10 Functions

• MIX mode

STATUS

DATA/CTRL

BANK MSB/MAX

BANK LSB/MIN

TOGGLE ON-OFF

/NUMBER OF PGM

DEC

/NO

INC

/YES

MEMORY

EDIT

WRITE

/EXIT

±10

F06

F00

11 15

31 35

41 45

51 55

NORMAL — MIX

FUNCTION

Function memory (5 types)

Program change memory

(5 x 5 types)

[In this mode, Program Change Memory and Function Memory are mixed.]

Upper level foot switches [6]-[0]

Lower level foot switches [1]-[5]

• To access all 100 (F00-F99) Function Memory types, press

the [FUNCTION] switch, and it’s lamp will light.

• In the MIX mode, Program Change memory (25 memories)

is stored and played independent of Program Change

memory in the NORMAL mode.

■ Foot Controller Settings.....................................................................

■ Bulk Dump ...........................................................................................

Internal data for the Normal mode Program Change Memory, the Mix mode Program Change Memory, and

Function Memory and Foot Controller Memory (1-5) can be transmitted via MIDI OUT. (see page 25)

■ All Memory MIDI Channel Number Assign........................................

The settings for all MIDI channels, in all assigned memories, can be set to the same MIDI channel. (see page 24)

Sets parameters for the onboard Foot Controller and the external Foot Controllers 2-5. (see page 22)

Normal Mode

Both Program Change Memory and Function Memory can be accessed in the Normal

Mode.

Press the [FUNCTION] to switch between Program Change Memory and Function

Memory.

There are 100 memory allocations for Function data

(control change etc.). By selecting a memory

number, its stored function data is transmitted to

external devices via the MIDI OUT terminal.

There are 128 memory allocations for Program

Change data. By selecting a memory number, its

stored program change is transmitted to external

devices via the MIDI OUT terminal.

Function Memory

Program Change Memory

Press the [POWER ON/OFF] switch on the rear panel to turn

the power on.

Set the [FUNCTION NORMAL—MIX] switch on the rear

panel to the [NORMAL] position.

• Program Change Memory (128 types)

• Function Memory (100 types)

Function lamp is lit.

Function lamp is off.

001 128

F00 F99

Press [FUNCTION] to switch between Program Change

Memory (see page 9) and Function Memory (see page 12).

POWER

ON/ OFF

NORMAL — MIX

FUNCTION

Normal Mode

If FUNCTION lamp is lit, press [FUNCTION], so that the lamp is off, and Program Change Memory

is enabled.

Program Change Memory transmits MIDI channel numbers 1-16 and program change data (001-128)

that are stored in memory.

There are 128 memory allocations in which Program Change data can be saved. Also, Bank

Select data (00=MSB, 20=LSB) can be transmitted along with Program Change data.

Program Change Memory

■ Program Change Memory Control (Transmit) ..................................

STATUS

DATA/CTRL

BANK MSB/MAX

BANK LSB/MIN

TOGGLE ON-OFF

/NUMBER OF PGM

DEC

/NO

INC

/YES

MEMORY

EDIT

WRITE

/EXIT

±10

8.8.8.

[1]-[0], [x10] foot switches

• Press [FUNCTION] to enable Function Memory

(the FUNCTION lamp lights).

084

081

Example: To change the current memory number

084 to 081 press [1] once.

To change or select the 1's digit.

To change and select both the 10's and

1's digits.

Press one of the [1]-[0] foot switches.

Press [x10]. (The 10's digit of the LED

flashes indicating input standby.) Press [1]-[0], to

select the 10's digit value. (The 1's digit flashes

indicating input standby.)

Once again press [1]-[0] to select the 1's digit

value.

Select a Memory Number

Example: To change the current Memory Number

023 to 082, press [x10], [8], and [2] in

that order.

023 082

Program changes and bank select data are transmitted when a memory number is selected with the [1]-[0]

and [x10] foot switches. A total of 128 (001-128) memory allocations are available for storing such data.

Normal Mode

To change and select all digits.

Press [x10] two times.

If the 100's digit value is 1, it will change to

0, if it is 0 it will change to 1. (The 10's digit

flashes indicating input standby.)

Press [1]-[0], to select the 10's digit value.

(The 1's digit flashes indicating input standby.)

Once again, press [1]-[0] to select the 1's digit

value.

• When [x10] is pressed twice, the 100's digit value will

alternate between 1 and 0.

• Attempting to select the number 000, will result in 001

being selected. Also, inputting any value above 128

will result in 128 being selected.

■ Program Change Memory Edit...........................................................

The following 4 types of MIDI data can be transmitted with Program Change Memory.

The transmitting Channel Number and MIDI data can be stored to individual Memory Numbers.

• STATUS

C0 CF

C0 Channel 1

C1 Channel 2

C2 Channel 3

C3 Channel 4

C4 Channel 5

C5 Channel 6

C6 Channel 7

C7 Channel 8

C8 Channel 9

C9 Channel 10

CA Channel 11

Cb Channel 12

CC Channel 13

Cd Channel 14

CE Channel 15

CF Channel 16

Cn (n=MIDI channel numbers 1-16) assigns the MIDI channel for voice selection. The

number is shown in hexadecimal.

Example: To change the current Memory Number 048 to

126, press [x10], [X10], [2], [6] in that order.

Two times

048 126

• BANK MSB (Bank Select MSB)

• BANK LSB (Bank Select LSB)

000oFF 127

Bank select numbers are used to access voices other than the 128 voices normally available in

MIDI devices and GM devices. Program change data and bank select data (BANK MSB/

LSB:off, 000-127) must be transmitted together to access these voices.

Refer to the owner's manual of the receiving device for specific information on bank select data.

• DATA/CTRL

001 128

Sets program numbers (voice numbers 001-128) for transmission.

Refer to the owner's manual of the receiving device for details on voice assignments.

Refer to a GM voice map for the 128 voice allocations of GM MIDI devices.

• The default settings for each memory (001-128) is as

follows.

STATUS=C0 (Channel Number 1), DATA/CTRL=001-128

(same as the memory number), BANK MSB/MAX=off,

BANK LSB/MIN=off.

Normal Mode

How to Edit Memory

If the FUNCTION lamp is lit, press [FUNCTION], so that the

lamp is off, and Program Change Memory is enabled.

Select the Memory Number to be edited (see page 9). Press

[MEMORY EDIT] to edit to begin editing that Memory

Number. (The lamp above that foot switch and the STATUS

lamp will flash.)

Press [MEMORY EDIT] to cycle through the 4 edit param-

eters (the selected parameter’s light will flash).

Use [INC/YES] and [DEC/NO] to edit the parameter.

Press [INC/YES] to increase the value shown in the LED

display by 1, press [DEC/NO] to decrease the value by 1. By

holding a button, values will continuously increase or de-

crease.

Hold the [INC/YES] button and press the [DEC/NO] button

and the value shown in the LED display will increase by 10.

Repeatedly press [DEC/NO] to continue increasing the value

by 10.

Hold the [DEC/NO] button and press the [INC/YES] button

and the value shown in the LED display will decrease by 10.

Repeatedly press [INC/YES] to continue decreasing the value

by 10.

• TOGGLE ON-OFF/NUMBER OF PGM can not be

selected from Program Change Memory.

MEMORY

EDIT

Increase by 10

MEMORY

EDIT

DEC

/NO

INC

/YES

±10

DEC

/NO

INC

/YES

±10

001 128

128 001

DEC

/NO

INC

/YES

±10

DEC

/NO

INC

/YES

±10

Decrease by 10

WRITE

/EXIT

007

STATUS

DATA/CTRL

BANK MSB/MAX

BANK LSB/MIN

TOGGLE ON-OFF

/NUMBER OF PGM

STATUS settings

DATA/CONTROL settings

BANK MSB settings

BANK LSB settings

Press [INC/YES], to save the edited data to the current

Memory Number, The MFC10 will return to its normal control

mode.

Press [DEC/NO] to cancel the save operation of the edited

data. At this time the memory will revert to its pre-edited

contents.

DEC

/NO

INC

/YES

±10

DEC

/NO

INC

/YES

±10

• Another Memory Number from the same bank (10’s digit bank) can be easily edited by

pressing [1] - [0] without exiting from the edit mode. You must execute or cancel the save

operation for the currently edited data (the current Memory Number will flash) before

proceeding to edit the new number. Use [INC/YES] to execute or [DEC/NO] to cancel the

save operation. If data has not been edited, the Memory Number will not flash and the

newly selected Memory Number will be shown in the display.

After the desired parameters have been edited in steps 2 and 3,

press [WRITE/EXIT]. The Memory Number shown in the

LED display will flash. (The flashing number indicates

confirmation is necessary to proceed or cancel saving of the

edited data.)

• If data has not been edited, the Memory Number will

not flash and the MFC10 will return to its normal

control mode.

Normal Mode

Function Memory

Press [FUNCTION], the FUNCTION lamp will light, and Function Memory is enabled.

Function Memory stores and transmits MIDI data such as note on/off, control change, program

change, song select, start, continue, stop, etc., in its memory.

There are 100 (F00-F99) memory allocations in which Function Data can be saved.

• Press [FUNCTION] to enable to Program

Change Memory. (The FUNCTION lamp is off.)

■ Function Memory Control (Transmit) ................................................

Function data is transmitted when a Memory Number is selected using the [1]-[0] and [x10] foot switches. A total

of 100 (F00-F99) memory allocations are available for storing such data.

Example: To change the Memory Number “F84” to “F81”

press the [1] foot switch once.

Example: To change the Memory Number “F23” to “F47”,

press [x10], [4], [7] in that order.

F84

F81

Press one of the [1]-[0] foot switches.

Press the [x10] foot switch. (The 10's digit of

the LED flashes indicating input standby.) Press

[1]-[0], to select the 10's digit value. (The 1's digit

flashes indicating input standby.)

Once again press [1]-[0] to select the 1's digit

value.

To change and select the 1's digit.

To change and select both the 10's and

1's digits.

F23 F47

Select a Memory Number

Normal Mode

■ Edit Function Memory ........................................................................

The following 9 types of MIDI data can be transmitted with Function Memory.

The transmitting Channel Number and MIDI data can be stored to individual Memory Numbers.

DATA/CTRL 000-127 (Note Number)

BANK MSB/MAX 001-127 (Note On Velocity)

BANK LSB/MIN 001-127 (Note Off Velocity)

TOGGLE ON-OFF

Pn1-Pn4 (see page 18)

/NUMBER OF PGM

54 56 58 66 68 7061 63

55 57 59 60

62 64 65 67 69 71

................

Transmits keyboard Note On/Off data. If a different note is set to each foot switch, the

foot switches can be used to play a scale. Also, if a sampler is connected to the MFC10 the

foot switches can be used to trigger samples.

•Control Change (b) [STATUS=b0-bF]

DATA/CTRL 000-127 (Control Number)

BANK MSB/MAX 000-127 (Switch On Data)

BANK LSB/MIN 000-127 (Switch Off Data)

TOGGLE ON-OFF

off, on, Pn1-Pn4 (see page 18)

/NUMBER OF PGM

Note Number

•Note On/Off (9) [STATUS=90-9F]

90 9F

b0 bF

Normal Mode

Control Change List (for GM, XG supported devices)

Control

Function GM XG

Number

0 Bank Select N Y

1 Modulation Y Y

5 Portamento Time N Y

6 Data Entry Y Y

7 Main Volume Y Y

10 Pan Pot Y Y

11 Expression Y Y

32 Bank Select N Y

38 Data Entry Y Y

64 Hold 1 (Damper Pedal) Y Y

65 Portamento N Y

66 Sostenuto (Chord Hold) N Y

67 Soft Pedal N Y

71 Harmonic Content N Y

72 Release Time N Y

73 Attack Time N Y

74 Brightness N Y

84 Portamento Control N Y

91 Extensive Use Effect 1 (Reverb) N Y

93 Extensive Use Effect 3 (Chorus) N Y

94 Extensive Use Effect 4 (Celeste) N Y

96 Data-Increment N Y

97 Data-Decrement N Y

98 NRPN(LSB) N Y

99 NRPN(MSB) N Y

100 RPN(LSB) Y Y

101 RPN(MSB) Y Y

120 All Sound Off N Y

121 Reset All Controllers Y Y

122 Local Control N Y

123 All Note Off Y Y

124 Omni Off N Y

125 Omni On N Y

126 Mono On N Y

127 Poly On N Y

GM (GM System Level 1)

[GM] (General MIDI is in addition to the MIDI standard which ensures that any GM-compatible

music data can be accurately played on any GM-compatible tone generator, regardless of the

maker. The GM mark is affixed to all software and hardware products that support the General

MIDI standard.

[XG] is a MIDI format created by Yamaha which significantly imporves and expands upon the

General MIDI standard by providing a greater variety of high-quality Voices plus considerably

enhanced effect operations—while being fully compatible with GM.

GENERAL

•Program Change (C) [STATUS=C0-CF]

C0 CF

DATA/CTRL 001-128 (Program Number)

BANK MSB/MAX off, 000~127

BANK LSB/MIN off, 000~127

TOGGLE ON-OFF

Pn1-Pn4

(see page 18)

/NUMBER OF PGM

•Song Select (F3) [STATUS=F3]

DATA/CTRL 000-127 (Song Number)

•Start (FA) [STATUS=FA]

Other parameters cannot be set.

Y...Yes N...No

Normal Mode

• Section Control (F0) [STATUS=F0]

* When c41 or c42 is selected, the device number must be set in BANK MSB/MAX.

•Continue (Fb) [STATUS=Fb]

Other parameters cannot be set.

•Stop (FC) [STATUS=FC]

Other parameters cannot be set.

DATA/CTRL c01-c42 (Section Number)

BANK MSB/MAX 01-16, - - -

(Device Number)

c17 Fill In AA1

c18 Fill In AA2

c19 Fill In AA3

c20 Fill In AA4

c21 Fill In AA5

c22 Fill In AA6

c23 Fill In AA7

c24 Fill In AA8

c25 Fill In AB1

c26 Fill In AB2

c27 Fill In AB3

c28 Fill In AB4

c29 Fill In AB5

c30 Fill In AB6

c31 Fill In AB7

c32 Fill In AB8

c33 Ending 1

c34 Ending 2

c35 Ending 3

c36 Ending 4

c37 Ending 5

c38 Ending 6

c39 Ending 7

c40 Ending 8

c41 Reset Start

c42 Stop & Rewind

c01 Intro 1

c02 Intro 2

c03 Intro 3

c04 Intro 4

c05 Intro 5

c06 Intro 6

c07 Intro 7

c08 Intro 8

c09 Main 1

c10 Main 2

c11 Main 3

c12 Main 4

c13 Main 5

c14 Main 6

c15 Main 7

c16 Main 8

Data for section types that can be transmitted are listed below.

• Tempo Control (Ft) [STATUS=Ft]

DATA/CTRL 030~250 (Tempo Value)

The tempo of external devices can be controlled within a range of 30-250 beats per minute.

Normal Mode

How to Edit Memory

Select the Function Memory to be edited, press [MEMORY

EDIT], to begin editing that memory number. (The lamp above

the foot switch and the STATUS lamp will flash.)

Press [INC/YES] and [DEC/NO] to select the Status (transmit

MIDI data and MIDI channel number) (the STATUS lamp will

flash).

The 1's digit (MIDI channel number 1-16) of Status is shown in

hexadecimal. (see page 10)

Press [MEMORY EDIT] to select the parameters set in the

procedures above for editing (the lamp will flash).

Song Select Start Continue Stop

STATUS F3 FA Fb FC

DATA/CTRL 0-127 –– –

BANK MSB/MAX ––––

BANK LSB/MIN ––––

TOGGLE ON-OFF

––––

/NUMBER OF PGM

Note On/Note Off Control Change Program Change

STATUS

90-9F b0-bF C0-CF

(0-F indicates MIDI channel numbers)

DATA/CTRL Note Number Control Number Program Number

BANK MSB/MAX Note On Velocity Switch On Data Bank MSB

BANK LSB/MIN Note Off Velocity Switch Off Data Bank LSB

TOGGLE ON-OFF

Pn1-Pn4

Toggle On/Off

Pn1-Pn4

/NUMBER OF PGM Pn1-Pn4

90...9F Transmit Note On/Off

b0...bF Transmit Control Change

CO...CF Transmit Program Change

F3 Transmit Song Select

FA Transmit Start

Fb Transmit Continue

FC Transmit Stop

FO Transmit Section Control

Ft Transmit Tempo Control

MEMORY

EDIT

MEMORY

EDIT

MIDI data

Channel number

STATUS

DATA/CTRL

BANK MSB/MAX

BANK LSB/MIN

TOGGLE ON-OFF

/NUMBER OF PGM

STATUS

DATA/CTRL

BANK MSB/MAX

BANK LSB/MIN

TOGGLE ON-OFF

/NUMBER OF PGM

DEC

/NO

INC

/YES

±10

DEC

/NO

INC

/YES

±10

Normal Mode

Increase by 10

Section Control Tempo Control

STATUS F0 Ft

DATA/CTRL c01 - c42 030- 250

BANK MSB/MAX Channel Number (if c41, c42 is used) –

BANK LSB/MIN ––

TOGGLE ON-OFF

––

/NUMBER OF PGM

Press [INC/YES] or [DEC/NO] to edit parameter values.

Press [INC/YES] to increase the value shown in the LED

display by 1, press [DEC/NO] to decrease the value by 1. By

holding a button, values will continuously increase or decrease.

Hold the [INC/YES] button and press the [DEC/NO] button

and the value shown in the LED display will increase by 10.

Repeatedly press [DEC/NO] to continue increasing the value

by 10.

Hold the [DEC/NO] button and press the [INC/YES] button

and the value shown in the LED display will decrease by 10.

Repeatedly press [INC/YES] to continue decreasing the value

by 10.

DEC

/NO

INC

/YES

±10

DEC

/NO

INC

/YES

±10

DEC

/NO

INC

/YES

±10

001 128

128 001

*(—) is displayed to indicate parameters that cannot be selected.

WRITE

/EXIT

F07

After the desired parameters have been edited in steps 3 and 4,

press [WRITE/EXIT]. The Memory Number shown in the

LED display will flash.

• If data has not been edited, the Memory Number will

not flash and the MFC10 will return to its normal

control mode.

Press [INC/YES], to save the edited data to the current

Memory Number, The MFC10 will return to its normal control

mode.

Press [DEC/NO] to cancel the save operation of the edited

data. At this time the memory will revert to its pre-edited

condition.

Decrease by 10

DEC

/NO

INC

/YES

±10

• Another Memory Number from the same bank (10’s digit bank) can be easily edited by pressing [1] - [0]

without exiting from the edit mode. You must execute or cancel the save operation for the currently

edited data (the current Memory Number will flash) before proceeding to edit the new number. Use [INC/

YES] to execute or [DEC/NO] to cancel the save operation. If data has not been edited, the Memory

Number will not flash and the newly selected Memory Number will be shown in the display.

DEC

/NO

INC

/YES

±10

DEC

/NO

INC

/YES

±10

About the TOGGLE ON-OFF/NUMBER OF PGM settings.

Normal Mode

TOGGLE ON-OFF/NUMBER OF PGM contains the settings for “on, off, Pn1, Pn2, Pn3, Pn4”. According to the setting, you can use the

foot switch to operate as a toggle on-off, or simultaneously transmit several MIDI data.

TOGGLE ON-OFF settings

TOGGLE ON-OFF settings can be used in Function Memory that are saved with control change data.

• [on]...... Press the foot switch and the MAX value (switch on data) is continuously transmitted. Press the foot switch

once again and the MIN value (switch off data) is transmitted. The foot switch’s lamp will flash from the

time the MAX value is transmitted, until the MIN value is transmitted. Even if another foot switch is pressed,

the lamp will remain flashing. (The flashing lamp indicates continuous transmission of the MAX value.)

• [oFF]....Hold the foot switch and the MAX value (switch on data) is transmitted. Release the foot switch and the

MIN value (switch off data) is transmitted.

MIDI Data Simultaneous Transmission (Pn1-Pn4)

Pn1-Pn4 settings can be used in Function Memory that are saved with Note ON/OFF, control change, and program

change data.

Within Function Memories F00-F49, up to 4 of the same type of MIDI data (one of the following— Note On/Off,

Control Change, Program Change) can be simultaneously transmitted.

Pn4

Pn3

Pn2

Pn1

Pn4

Pn3

Pn2

Pn1

Pn4

Pn3

Pn2

Pn1

F00 F01 F49

For example, you can transmit several note on/off data over the same MIDI channel to play chords, or transmit control

change data over several MIDI channels to simultaneously control external effectors. Also, you can simultaneously

change the voices of several devices by transmitting Program Change Data over several MIDI channels.

■ Pn1-Pn4 Settings

Select the memory number to be set.

2 Press [MEMORY EDIT] and select “TOGGLE ON-OFF/

NUMBER OF PGM”.

3 Press [INC/YES] or [DEC/NO] and select “Pn1” (“Pn1” is

automatically selected when the edit operation is entered).

4 Select each parameter (STATUS, DATA/CTRL, etc.) using

[MEMORY EDIT], and set as required using [INC/YES] and

[DEC/NO].

5 After setting all parameters for “Pn1”, repeat steps 2 and 3 to

select “Pn2”. Repeat step 4 to select and set each parameter as

required.

6 In the same manner as “Pn2”, set parameters for “Pn3”, and “Pn4”

if necessary.

MEMORY

EDIT

Pn1

DEC

/NO

INC

/YES

±10

DEC

/NO

INC

/YES

±10

Pn2

MEMORY

EDIT

STATUS

DATA/CTRL

BANK MSB/MAX

BANK LSB/MIN

TOGGLE ON-OFF

/NUMBER OF PGM

• When “Pn1-Pn4” is set, the toggle setting will automatically be set to ON.

• If data is stored in Memory Numbers F00-F49, “Pn1” will automatically be selected when the Memory Number is

edited again.

MIX Mode

In the MIX mode, both Program Change data and Function data can be accessed at the

same time without having to change between modes with the [FUNCTION] switch. This

mode provides quick transmission of Program Change data and Function data.

In this mode, up to 25 different Program memories (independent of the NORMAL mode)

can be saved and accessed from the lower level of foot switches [1]-[5], and up to 5

different Function memories can be saved and accessed from the upper level of foot

switches [6]-[0]. Each of those memories can be selected and transmitted with the [1]-[0]

and [x10] foot switches.

Set the [FUNCTION NORMAL-MIX] switch on the

rear panel to the [MIX] position.

NORMAL — MIX

FUNCTION

Press [FUNCTION] and turn off the FUNCTION

lamp.

If [FUNCTION] is pressed while in the MIX mode

(the FUNCTION lamp lights), the MIX mode’s

FUNCTION memory (see page 21) will be enabled. All

foot switches can access the MFC10’s 100 FUNCTION

memories.

The 10's digit setting is valid when the MFC10 is

returned to the MIX mode. Press [FUNCTION] once

again, the FUNCTION lamp turns off, and the MFC10

is returned to MIX mode.

* The contents of each Function Memory number is same data between NORMAL mode and MIX mode. Program

Change Memory exists independently in each mode.

* Default setting for Program Change Memory in the MIX mode.

11[C0, 00], 12[C0, 01], 13[C0, 02], 14[C0, 03], 15[C0, 04], 21[C0, 05], 22[C0, 06], ...

La pagina sta caricando ...

Yamaha MFC10 Manuale del proprietario

Marca: Yamaha

Modello: MFC10

Categoria: Pianoforti digitali

Tipo: Manuale del proprietario

Scarica il pdf

rapporto

in altre lingue

English: Yamaha MFC10 Owner's manual
français: Yamaha MFC10 Le manuel du propriétaire
español: Yamaha MFC10 El manual del propietario
Deutsch: Yamaha MFC10 Bedienungsanleitung
русский: Yamaha MFC10 Инструкция по применению
Nederlands: Yamaha MFC10 de handleiding
português: Yamaha MFC10 Manual do proprietário
dansk: Yamaha MFC10 Brugervejledning
čeština: Yamaha MFC10 Návod k obsluze
polski: Yamaha MFC10 Instrukcja obsługi
svenska: Yamaha MFC10 Bruksanvisning
Türkçe: Yamaha MFC10 El kitabı
suomi: Yamaha MFC10 Omistajan opas
română: Yamaha MFC10 Manualul proprietarului

Documenti correlati

Altri documenti

AEG WX7-60CE1 Manuale utente