Philips GC4860/02 Manuale utente

GC4800 series

User manual

1

GC4800 series

ENGLISH 6

ESPAÑOL 23

ITALIANO 42

PORTUGUÊS 60

TÜRKÇE 78

6

Introduction

Congratulations on your purchase and welcome

to Philips! To fully benet from the support that

Philips offers, register your product at

www.philips.com/welcome.

General description (Fig. 1)

1 Spray nozzle

2 Filling opening

3 Spray button

4 Steam control

5 Steam boost button

6 Ionic DeepSteam button (GC4880, GC4875,

GC4870 only)

7 Ionic DeepSteam light (GC4880, GC4875,

GC4870 only)

8 Temperature dial

9 Amber temperature light (all types)/red auto-

off light GC4891/GC4890/GC4880/GC4875/

GC4870/GC4865/GC4860/GC4856/GC4855/

GC4852/GC4851/ GC4850 only).

10 Mains cord

11 Type plate

12 Soleplate

13 Calc-Clean button

Not shown: Heat-resistant protective cover

(GC4880 only)

Not shown: lling cup

Important

Read this user manual carefully before

you use the appliance and save it for

future reference.

ENGLISH

Danger

- Never immerse the iron in water.

Warning

- Check if the voltage indicated on the

type plate corresponds to the local

mains voltage before you connect the

appliance.

- Do not use the appliance if the plug,

the mains cord or the appliance

itself shows visible damage, or if the

appliance has been dropped or leaks.

- If the mains cord is damaged, you

must have it replaced by Philips, a

service centre authorised by Philips

or similarly qualied persons in order

to avoid a hazard.

- Never leave the appliance unattended

when it is connected to the mains.

- This appliance is not intended for use

by persons (including children) with

reduced physical, sensory or mental

capabilities, or lack of experience

and knowledge, unless they have

been given supervision or instruction

concerning use of the appliance by a

person responsible for their safety.

ENGLISH 7

- Children should be supervised to ensure

that they do not play with the appliance.

- Do not let the mains cord come into

contact with the hot soleplate of the

iron.

Caution

- Only connect the appliance to an

earthed wall socket.

- Check the mains cord regularly for

possible damage.

- The soleplate of the iron can become

extremely hot and may cause burns if

touched.

- When you have nished ironing, when

you clean the appliance, when you ll

or empty the water tank and also when

you leave the iron even for a short

while: set the steam control to position

0, put the iron on its heel and remove

the mains plug from the wall socket.

- Always place and use the iron on a

stable, level and horizontal surface.

- Do not put perfume, vinegar, starch,

descaling agents, ironing aids or other

chemicals in the water tank.

- This appliance is intended for

household use only.

ENGLISH8

Electromagnetic elds (EMF)

This Philips appliance complies with all standards

regarding electromagnetic elds (EMF). If handled

properly and according to the instructions in this

user manual, the appliance is safe to use based on

scientic evidence available today.

Before rst use

1 Remove any sticker, protective foil or plastic

from the soleplate.

2 Rinseanddrythellingcup.

Preparing for use

Filling the water tank

Type of water to be used

You can use normal tap water to ll the water tank.

Tip: If the tap water in your area is very hard, we

advise you to mix it with an equal amount of distilled

water. Do not use distilled water only.

1 Makesuretheapplianceisunplugged.

2 Set the steam control to position 0

(= no steam).

3 Openthecapofthellingopening.

4 Tilttheironbackwardsandusethellingcup

tollthewatertankwithtapwateruptothe

maximumlevel.

Do not ll the water tank beyond the MAX

indication.

ENGLISH 9

Donotputperfume,vinegar,starch,descaling

agents,ironingaidsorotherchemicalsinthewater

tank.

5 Closethecapofthellingopening(‘click’).

Selecting the temperature and steam

setting

Temperature and steam settings

Fabric type Temperature

setting

Steam

setting

Steam

boost

Ionic

DeepSteam

(specic

types only)

Linen MAX 5-6

\

yes

Cotton 3 3-4

\

yes

Wool 2 1-2 N.A. yes

Silk 1 0 N.A. N.A.

Synthetic

fabrics (e.g.

acrylic, nylon,

polyamide,

polyester)

1 0 N.A. N.A.

1 Specictypesonly:removetheheat-resistant

protective cover.

Donotleavetheheat-resistantprotectivecover

onthesoleplateduringironing.

ENGLISH10

2 Puttheirononitsheel.

3 Tosettherequiredironingtemperature,

turnthetemperaturedialtotheappropriate

position(seethe‘Temperatureandsteam

settings’tableabove).

Check the laundry care label for the fabric type.

If you do not know what kind or kinds of fabric

an article is made of, determine the right ironing

temperature by ironing a part that is not visible

when you wear or use the article.

Silk, woollen and synthetic materials: iron the reverse

side of the fabric to prevent shiny patches. To

prevent stains, do not use the spray function.

Start ironing the articles that require the lowest

ironing temperature, such as those made of synthetic

bres.

4 Settheappropriatesteamsetting(seethe

‘Temperatureandsteamsettings’tableabove).

Note: Make sure that the steam setting you select is

suitable for the set ironing temperature.

5 Putthemainspluginanearthedwallsocket.

, Theambertemperaturelightgoeson.

6 Whentheambertemperaturelighthasgone

out,waitawhilebeforeyoustartironing.

, Thetemperaturelightgoesonfromtimeto

timeduringironing.

Using the appliance

Note: The iron may give off some smoke when you use

it for the rst time. This ceases after a short while.

ENGLISH 11

Ironing without steam

1 Set the steam control to position 0

(= no steam).

2 Settherequiredironingtemperature(see

chapter‘Preparingforuse’,section‘Selecting

thetemperatureandsteamsetting’).

Steam ironing

1 Makesurethatthereiswaterinthewater

tank.

2 Settherequiredironingtemperature(see

chapter‘Preparingforuse’,section‘Selecting

thetemperatureandsteamsetting’).

3 Settheappropriatesteamsetting(see

chapter‘Preparingforuse’,section‘Selecting

thetemperatureandsteamsetting’).

Note: The iron starts to produce steam as soon as it

reaches the set temperature.

Steam ironing with extra steam

1 Forextrasteamduringironing,pressandhold

thesteamboostbutton.

ENGLISH12

Ironing with Ionic DeepSteam (specic

types only)

When you use the Ionic DeepSteam function during

steam ironing, the steam produced is ner than

during regular steam ironing. Fine steam reaches

deeper, especially into thick fabrics. This helps you

to remove stubborn creases easily.

1 Makesurethatthereiswaterinthewater

tank.

2 Settherequiredironingtemperature(see

chapter‘Preparingforuse’,section‘Selecting

thetemperatureandsteamsetting’).

3 Settheappropriatesteamsetting(seechapter

‘Preparingforuse’,section‘Selectingthe

temperatureandsteamsetting’).

4 PresstheIonicDeepSteambuttononceto

switchontheIonicDeepSteamfunction.

, TheblueIonicDeepSteamlightgoesonandyou

hearahummingsound.

, TheironnowproducesIonicDeepSteamto

helpyouremoveeventhetoughestcreases.

5 PresstheIonicDeepSteambuttonagainto

switchofftheIonicDeepSteamfunction.

ENGLISH 13

Note: The Ionic DeepSteam function is only effective

when it is used in combination with a steam setting

and a temperature setting between 2 and MAX.

Note: Do not use the Ionic DeepSteam function when

you iron without steam and/or at low temperature

settings. However, ironing at low temperatures without

steam with the Ionic DeepSteam function switched on

will not damage the iron.

Note: The Ionic DeepSteam output may vary from time

to time, depending on the ironing temperature.

Features

Spray function

You can use the spray function at any temperature

to moisten the article to be ironed. This helps

remove stubborn creases.

1 Makesurethatthereiswaterinthewater

tank.

2 Pressthespraybuttonseveraltimesto

moisten the article to be ironed.

Steam boost function

A steam boost from the special Steam Tip soleplate

helps remove stubborn creases. The steam boost

enhances the distribution of steam into every part of

your garment.

The steam boost function can only be used at

temperature settings between 3 and MAX.

1 Pressandreleasethesteamboostbutton.

ENGLISH14

Vertical steam boost

1 Youcanalsousethesteamboost

functionwhenyouholdtheironinvertical

position.

This is useful for removing creases from hanging

clothes, curtains etc.

Never direct the steam at people.

Drip stop

This iron is equipped with a drip-stop function: the

iron automatically stops producing steam when

the temperature is too low, to prevent water from

dripping out of the soleplate. When this happens,

you may hear a sound.

Automatic shut-off function (specic types only)

The automatic shut-off function automatically switches

off the iron if it has not been moved for a while.

, Theredauto-offlightashestoindicatethat

theironhasbeenswitchedoffbytheautomatic

shut-offfunction.

To let the iron heat up again:

1 Pickuptheironormoveitslightly.

, Theredauto-offlightgoesout.

, Ifthetemperatureofthesoleplatehasdropped

belowthesetironingtemperature,theamber

temperaturelightgoeson.

2 Iftheambertemperaturelightgoesonafter

youhavemovedtheiron,waitforittogoout

beforeyoustartironing.

Note: If the amber temperature light does not go on

after you move the iron, the soleplate still has the right

temperature and the iron is ready for use.

ENGLISH 15

Cleaning and maintenance

Cleaning

1 Set the steam control to position 0, remove

theplugfromthewallsocketandlettheiron

cool down.

2 Wipeakesandanyotherdepositsoffthe

soleplatewithadampclothandanon-abrasive

(liquid)cleaningagent.

To keep the soleplate smooth, avoid hard contact

withmetalobjects.Neveruseascouringpad,

vinegarorotherchemicalstocleanthesoleplate.

3 Cleantheupperpartoftheironwithadamp

cloth.

4 Regularlyrinsethewatertankwithwater.

Emptythewatertankafteryouhaverinsedit.

Double-Active Calc System

- The Anti-Calc tablet prevents scale from clogging

the steam vents. This tablet is constantly active and

does not need to be replaced.

- The Calc-Clean function removes the scale

particles from the iron.

Using the Calc-Clean function

Use the Calc-Clean function once every two weeks.

If the water in your area is very hard (i.e. when akes

come out of the soleplate during ironing), use the

Calc-Clean function more frequently.

1 Makesuretheapplianceisunplugged.

2 Set the steam control to position 0.

3 Fill the water tank to the MAX level.

ENGLISH16

Donotputvinegarorotherdescalingagentsin

the water tank.

4 SetthetemperaturedialtoMAX.

5 Putthepluginanearthedwallsocket.

6 Unplugtheironwhenthetemperature

lightgoesout.

7 Hold the iron over the sink, press and hold the

Calc-Cleanbuttonandgentlyshaketheironto

and fro.

, Steamandboilingwatercomeoutofthe

soleplate.Impuritiesandakes(ifany)are

ushedout.

8 ReleasetheCalc-Cleanbuttonassoonasall

thewaterinthetankhasbeenusedup.

9 RepeattheCalc-Cleanprocessiftheironstill

containsalotofimpurities.

After the Calc-Clean process

1 Puttheplugbackintothewallsocketandlet

theironheatuptoletthesoleplatedry.

2 Unplugtheironwhenithasreachedtheset

ironingtemperature.

3 Movethehotirongentlyoverapieceofused

cloth to remove any water stains that may have

formed on the soleplate.

4 Lettheironcooldownbeforeyoustoreit.

ENGLISH 17

Storage

1 Setthesteamcontroltoposition0andunplug

the iron.

2 Empty the water tank.

3 Let the iron cool down in a safe place.

4 Windthemainscordaroundthecordstorage

facilityandxitwiththecordclip.

5 Store the iron on its heel in a dry and safe

place.

Heat-resistant protective cover

(specic types only)

You can store the iron on the heat-resistant

protective cover immediately after ironing. It is not

necessary to let the iron cool down rst.

Donotusetheheat-resistantprotectivecover

duringironing.

1 Windthemainscordaroundthecordstorage

facilityandxitwiththecordclip.

2 Puttheironontheheat-resistantprotective

cover.

ENGLISH18

Environment

- Do not throw away the appliance with the normal

household waste at the end of its life, but hand

it in at an ofcial collection point for recycling. By

doing this, you help to preserve the environment.

Guarantee and service

If you need information or if you have a problem,

please visit the Philips website at www.philips.com

or contact the Philips Consumer Care Centre

in your country (you nd its phone number in

the worldwide guarantee leaet). If there is no

Consumer Care Centre in your country, go to your

local Philips dealer.

Troubleshooting

If the appliance does not work or does not work

properly, rst check the list below. If the problem

is not mentioned in this list, the appliance probably

has a defect. In that case we advise you to take the

appliance to your dealer or to an authorised Philips

service centre.

ENGLISH 19

Problem Possiblecause Solution

The iron

is plugged

in, but the

soleplate is

cold.

There is a

connection

problem.

Check the mains cord, the plug

and the wall socket.

The temperature

dial is set to MIN.

Set the temperature dial to the

required position.

The iron

does not

produce any

steam.

There is not

enough water in

the water tank.

Fill the water tank (see chapter

‘Preparing for use’, section ‘Filling

the water tank’).

The steam control

is set to position 0.

Set the steam control to a

position between 1 and 6 (see

chapter ‘Using the appliance’,

section ‘Steam ironing’).

The iron is not hot

enough and/or the

drip-stop function

has been activated.

Set an ironing temperature that

is suitable for steam ironing ( 2

to MAX). Put the iron on its heel

and wait until the temperature

light has gone out before you

start ironing.

The iron

does not

produce a

steam boost.

You have used

the steam boost

function too often

within a very short

period.

Continue ironing in horizontal

position and wait a while before

you use the steam boost function

again.

ENGLISH20

La pagina sta caricando ...

Philips GC4860/02 Manuale utente

Philips GC4860/02 Manuale utente

in altre lingue

Documenti correlati