Scholtes SMLE 129 Instructions For Use Manual

Marca: Scholtes

Modello: SMLE 129

Categoria: Lavatrici

Tipo: Instructions For Use Manual

Contents

Installation, 2-3-4-5

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Instructions for the fitter

Care and maintenance, 6

Cutting off the water or electricity supply

Cleaning the washing machine

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Precautions and tips, 7

General safety

Disposal

Opening the porthole door manually

Description of the washing machine, 8-9

Control panel

Display

Running a wash cycle, 10

Wash cycles and functions, 11

Table of wash cycles

Wash functions

Detergents and laundry, 12

Detergent dispenser drawer

Preparing the laundry

Special wash cycles

Load balancing system

Troubleshooting, 13

Service, 14

SMLE 129

Instructions for use

WASHING MACHINE

English,1

Español,29Français,15

Italiano,43

Installation

! This instruction manual should be kept in a safe

place for future reference. If the washer dryer is

sold, transferred or moved, make sure that the

instruction manual remains with the machine so

that the new owner is able to familiarise himself/

herself with its operation and features.

! Read these instructions carefully: they contain

vital information relating to the safe installation

and operation of the appliance.

Unpacking and levelling

Unpacking

1. Remove the washer dryer from its packaging.

2. Make sure that the washer dryer has not been

damaged during the transportation process. If it

has been damaged, contact the retailer and do not

proceed any further with the installation process.

3. Remove the 4 pro-

tective screws (used

during transportation)

and the rubber washer

with the corresponding

spacer, located on the

rear part of the applian-

ce (see figure).

4. Close off the holes using the plastic plugs

provided.

5. Keep all the parts in a safe place: you will

need them again if the washer dryer needs to

be moved to another location.

! Packaging materials should not be used as

toys for children.

Levelling

1. Install the washer dryer on a flat sturdy floor,

without resting it up against walls, furniture ca-

binets or anything else.

2. If the floor is not per-

fectly level, compensa-

te for any unevenness

by tightening or loo-

sening the adjustable

front feet (see figure);

the angle of inclination,

measured in relation to

the worktop, must not

exceed 2°.

Levelling the machine correctly will provide it with

stability, help to avoid vibrations and excessive

noise and prevent it from shifting while it is ope-

rating. If it is placed on carpet or a rug, adjust

the feet in such a way as to allow a sufficient

ventilation space underneath the washer dryer.

Connecting the electricity and wa-

ter supplies

Connecting the water inlet hose

1. Connect the supply

pipe by screwing it to

a cold water tab using

a ¾ gas threaded con-

nection (see figure).

Before performing the

connection, allow the

water to run freely until

it is perfectly clear.

2. Connect the inlet

hose to the washer dr-

yer by screwing it onto

the corresponding wa-

ter inlet of the applian-

ce, which is situated on

the top right-hand side

of the rear part of the

appliance (see figure).

3. Make sure that the hose is not folded over

or bent.

! The water pressure at the tap must fall within

the values indicated in the Technical details table

(see next page).

! If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

! Never use second-hand hoses.

! Use the ones supplied with the machine.

65 - 100 cm

Connecting the drain hose

Connect the drain

hose, without bending

it, to a drainage duct or

a wall drain located at a

height between 65 and

100 cm from the floor;

alternatively, rest it on

the side of a washba-

sin or bathtub, faste-

ning the duct supplied

to the tap (see figure).

The free end of the

hose should not be

underwater.

! We advise against the use of hose extensions;

if it is absolutely necessary, the extension must

have the same diameter as the original hose and

must not exceed 150 cm in length.

Electrical connections

Before plugging the appliance into the electricity

socket, make sure that:

• the socket is earthed and complies with all

applicable laws;

• the socket is able to withstand the maximum

power load of the appliance as indicated in the

Technical data table (see opposite);

• the power supply voltage falls within the values

indicated in the Technical data table (see opposite);

• the socket is compatible with the plug of the

washer dryer. If this is not the case, replace the

socket or the plug.

! The washer dryer must not be installed ou-

tdoors, even in covered areas. It is extremely

dangerous to leave the appliance exposed to

rain, storms and other weather conditions.

! When the washer dryer has been installed, the

electricity socket must be within easy reach.

! Do not use extension cords or multiple sockets.

! The cable should not be bent or compressed.

! The power supply cable must only be replaced

by authorised technicians.

Warning! The company shall not be held responsible

in the event that these regulations are not respected.

The first wash cycle

Once the appliance has been installed, and before

you use it for the first time, run a wash cycle with

detergent and no laundry, using the wash cycle .

Technical details

Model

SMLE 129

Dimensions

59,5 cm wide

81,5 cm high

54,5 cm deep

Capacity

from 1 to 7 kg

Electric

connections

Please refer to the technical

data plate fixed to the ma-

chine.

Water

connections

maximum pressure 1 MPa

(10 bar) minimum pressure

0.05 MPa (0.5 bar) drum

capacity 52 litres

Spin speed

up to 1200 rpm

Test wash

cycles in

accordan-

ce with

directives

1061/2010

and

1015/2010

Programme

(1° press of

the button): Cotton standard

60°C;

Programme (2° press of

the button): Cotton standard

40°C.

This appliance is compliant

with the following European

Community Directives:

- 2004/108/CE (Electroma-

gnetic Compatibility)

- 2006/95/CE (Low Voltage)

- 2002/96/CE

Instructions for the fitter

Mounting the wooden panel onto the door

and inserting the machine into cabinets:

In the case where the machine must be shipped

for final installation after the wooden panel has

been mounted, we suggest leaving it in its ori-

ginal packaging. The packaging was designed

to make it possible to mount the wooden panel

onto the machine without removing it completely

(see figures below).

The wooden panel that covers the face of

the machine must not be less than 18 mm in

thickness and can be hinged on either the right

or left. For the sake of practicality when using

the machine, we recommend that the panel be

hinged on the same side as the door for the

machine itself - the left.

Tur seite

Door Mounting Accessories (Fig. 1-2-3-4-5).

Fig. 1

N° 2 Hinges

N° 1 Magnet N° 1 Magnet plate

N° 1 Rubber plug

N° 2 Hinge Supports

N° 4 Spacers

Fig. 2

Fig. 3 Fig. 4

Fig. 5

Fig. 4/B

- No. 6 type A self-threading screws, l =13 mm.

- No. 2 type B metric, countersunk screws, l =25;

for fastening the magnet plate to the cabinet.

- No. 4 type C metric screws, l =15 mm; for

mounting the hinge supports to the cabinet.

- No. 4 type D metric screws, l =7 mm; for

mounting the hinges on the supports.

Mounting the Parts onto the Face of the

Machine.

- Fit the hinge supports to the appliance front

panel, positioning the hole marked with an arrow

in fig. 1 so that it is on the inner side of the front

panel. Fit a spacer (fig. 4/B) between the surfa-

ces using type C screws.

- Fit the magnet plate at the top of the opposite

side, using type B screws to fix two spacers (fig.

4/B) between the plate and the surface.

Using the Drilling Template.

- To trace the positions of the holes on the left-

hand side of the panel, align the drilling template

to the top left side of the panel using the lines

traced on the extremities as a reference.

- To trace the positions of the holes on the right-

hand side of the panel, align the drilling template

to the top right side of the panel.

- Use an appropriately sized router to mill the holes

for the two hinges, the rubber plug and the magnet.

Mounding the Parts onto the Wooden Panel

(Door).

- Insert the hinges into the holes (the movable part of

the hinge must be positioned facing away from the

panel) and fasten them with the 4 type A screws.

- Insert the magnet into the top hole on the op-

posite side of the hinges and fasten it with the

two type B screws.

- Insert the rubber plug into the bottom hole.

The panel is now ready to be mounted onto the

machine.

Mounting the Panel into the machine.

Insert the nib of the hinge (indicated by the arrow

in fig. 2) into the hole for the hinge and push the

panel towards the front of the machine. Fasten

the two hinges with the type D screws.

Fastening the plinth guide.

If the machine is installed at the end of a set of

modular cabinets, mount either one or both of

the guides for the base molding (as shown in fig.

8). Adjust them for depth based on the position

of the base molding, and, if necessary, fasten

the base to the guides (fig. 9).

This is how to assemble the plinth guide (fig. 8):

Fasten angle P using screw R, insert plinth guide

Q into the special slot and once it is in the desired

position, lock it in place using angle P and screw R.

Inserting the machine into the Cabinet.

- Push the machine into the opening, aligning it

with the cabinets (fig. 6).

- Regulate the adjustable feet to raise the ma-

chine to the appropriate height.

- To adjust the position of the wooden panel in

both the vertical and horizontal directions, use

the C and D screws, as shown in fig. 7.

Important: close the lower part of the appliance

front by ensuring that the plinth rests against the floor.

Fig. 8 Fig. 9

Accessories provided for the height

adjustment.

The following can be found inside the polystyrene

lid (fig. 10): 2 crossbars (G), 1 strip (M)

the following can be found

inside the appliance drum:

4 additional feet (H),

4 screws (I),

4 screws (R),

4 nuts (L),

2 plinth guides (Q)

Adjusting the appliance height.

The height of the appliance can be adjusted (from

815 mm to 835 mm), by turning the 4 feet.

Should you require the appliance to be placed

higher than the above height, you need to use the

following accessories to raise it to up to 870 mm:

The two crossbars (G); the 4 feet (H); the 4 screws (I); the

4 nuts (L) then perform the following operations (fig. 11):

remove the 4 original feet, place a crossbar G at

the front of the appliance, fastening it in place

using screws I (screwing them in where the ori-

ginal feet were) then insert the new feet H.

Repeat the same operation at the back of the appliance.

Now adjust feet H to raise or lower the appliance

from 835 mm to 870 mm.

Once you have reached the desired height, lock

nuts L onto crossbar G.

To adjust the appliance to a height between 870

mm and 900 mm, you need to mount strip M,

adjusting feet H to the required height.

Insert the strip as follows:

loosen the three screws N situated at the front of

the Top cover of the appliance, insert strip M as

shown in fig. 12, then fasten screws N.

570

min

815

540

595

820 ÷ 900

600 min

Fig. 6 Fig. 7

Fig. 11 Fig. 12

Fig. 10

Care and maintenance

Cutting off the water and electri-

city supplies

• Turn off the water tap after every wash cycle.

This will limit wear on the hydraulic system

inside the washer dryer and help to prevent

leaks.

• Unplug the washer dryer when cleaning it

and during all maintenance work.

Cleaning the washer dryer

The outer parts and rubber components of the

appliance can be cleaned using a soft cloth

soaked in lukewarm soapy water. Do not use

solvents or abrasives.

Cleaning the detergent dispenser

drawer

Remove the dispenser

by raising it and pul-

ling it out (see figure).

Wash it under running

water; this operation

should be repeated

frequently.

Caring for the door and drum of

your appliance

• Always leave the porthole door ajar in order

to prevent unpleasant odours from forming.

Cleaning the pump

The washer dryer is fitted with a self-cleaning

pump which does not require any maintenan-

ce. Sometimes, small items (such as coins or

buttons) may fall into the pre-chamber which

protects the pump, situated in its bottom part.

! Make sure the wash cycle has finished and

unplug the appliance.

To access the pre-chamber:

1. unscrew the lid

by rotating it anti-

clockwise (see figu-

re): a little water may

trickle out. This is

perfectly normal;

2. clean the inside thoroughly;

3. screw the lid back on;

Checking the water inlet hose

Check the inlet hose at least once a year. If

there are any cracks, it should be replaced

immediately: during the wash cycles, water

pressure is very strong and a cracked hose

could easily split open.

! Never use second-hand hoses.

Precautions and tips

! This washing machine was designed and constructed in

accordance with international safety regulations. The fol-

lowing information is provided for safety reasons and must

therefore be read carefully.

General safety

• This appliance was designed for domestic use only.

• This appliance can be used by children aged

from 8 years and above and persons with re-

duced physical, sensory or mental capabilities

or lack of experience and knowledge if they

have been given supervision or instruction

concerning use of the appliance in a safe way

and understand the hazards involved. Children

shall not play with the appliance. Cleaning

and user maintenance shall not be made by

children without supervision.

• Do not touch the machine when barefoot or with wet or

damp hands or feet.

• Do not pull on the power supply cable when unplugging

the appliance from the electricity socket. Hold the plug

and pull.

• Do not touch the drained water as it may reach extreme-

ly high temperatures.

• Never force the porthole door. This could damage the

safety lock mechanism designed to prevent accidental

opening.

• If the appliance breaks down, do not under any circum-

stances access the internal mechanisms in an attempt

to repair it yourself.

• Always keep children well away from the appliance while

it is operating.

• If the appliance has to be moved, work in a group of two

or three people and handle it with the utmost care. Never

try to do this alone, because the appliance is very heavy.

• Before loading laundry into the washing machine, make

sure the drum is empty.

Disposal

• Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

• The European Directive 2002/96/EC on Waste

Electrical and Electronic Equipment, requires that

old household electrical appliances must not be

disposed of in the normal unsorted municipal waste

stream. Old appliances must be collected

separately in order to optimise the recovery and

recycling of the materials they contain and reduce

the impact on human health and the environment.

The crossed out “wheeled bin” symbol on the

product reminds you of your obligation, that when

you dispose of the appliance it must be separately

collected. Consumers should contact their local

authority or retailer for information concerning the

correct disposal of their old appliance.

Opening the porthole door manually

In the event that it is not possible to open the porthole door

due to a powercut, and if you wish to remove the laundry,

proceed as follows:

1. remove the plug from the electrical socket.

2. make sure the water level inside the machine is lower than

the door opening; if it is not, remove excess water using the

drain hose, collecting it in a bucket.

3. pull outwards using the tab as indicated in the figure, until

the plastic tie-rod is freed from its stop position; pull down-

wards and open the door at the same time.

Detergent dispenser drawer: used to dispense deter-

gents and washing additives (see “Detergents and laundry”).

ON/OFF button : press this briefly to switch the machine

on or off. The START/PAUSE indicator light, which flashes

slowly in a green colour shows that the machine is switched

on. To switch off the washing machine during the wash cycle,

press and hold the button for approximately 2 seconds; if

the button is pressed briefly or accidentally the machine will

not switch off. If the machine is switched off during a wash

cycle, this wash cycle will be cancelled.

WASH CYCLE SELECTOR buttons: used to set the desired

wash cycle (see “Table of wash cycles”).

MEMORY button: press and hold the button to store a cycle

with your own set of preferences in the memory of the machine.

To recall a previously stored cycle, press the MEMORY button.

FUNCTION buttons: press the button to select the desired

function. The corresponding indicator light on the display

will switch on.

SPIN button : press to reduce or completely exclude the

spin cycle - the value is indicated on the display.

TEMPERATURE button : press to decrease the tempe-

rature: the value will be shown on the display.

CONTROL PANEL LOCK button : to activate the control

panel lock, press and hold the button for approximately 2

seconds. When the symbol is illuminated, the control

panel is locked (apart from the ON/OFF key). This means

it is possible to prevent wash cycles from being modified

accidentally, especially where there are children in the home.

To deactivate the control panel lock, press and hold the

button for approximately 2 seconds.

DELAYED START button : press to set a delayed start

time for the selected wash cycle. The delay time will be shown

on the display.

START/PAUSE button with indicator light: when the gre-

en indicator light flashes slowly, press the button to start a

wash cycle. Once the cycle has begun the indicator light will

remain lit in a fixed manner. To pause the wash cycle, press

the button again; the indicator light will flash in an orange

colour. If the symbol is not illuminated, the door may be

opened. To start the wash cycle from the point at which it

was interrupted, press the button again.

Standby mode

This washing machine, in compliance with new energy saving

regulations, is fitted with an automatic standby system which

is enabled after about 30 minutes if no activity is detected.

Press the ON-OFF button briefly and wait for the machine

to start up again.

Consumption in off-mode: 0,5 W

Consumption in Left-on: 0,5 W

Description of the washing

machine

SPIN SPEED

Button

START/PAUSE

button with indicator

light

Control panel

TEMPERATURE

Button

WASH

CYCLE

SELECTOR

Buttons

Detergent dispenser drawer

FUNCTION

buttons

ON/OFF

button

DISPLAY

DELAYED

START

Button

MEMORY

Button

CONTROL PANEL

LOCK button

Display

The display is useful when programming the machine and provides a great deal of information.

The two upper strings A and B provide details of the wash cycle selected, the wash cycle phase in progress and all informa-

tion relating to the progress status of the wash cycle.

String C shows the time remaining until the end of the wash cycle in progress and, if a DELAYED START has been set, the

time remaining until the start of the selected wash cycle.

String D shows the maximum spin speed value (this depends on the selected wash cycle); if the wash cycle does not include

a spin cycle, the string remains unused.

String E shows the maximum temperature value which may be selected (this depends on the wash cycle used); if the tempe-

rature of the wash cycle cannot be modified, the string remains unused.

Indicator lights F correspond to the functions and light up when the selected function is compatible with the set wash cycle.

Door locked symbol

If the symbol is lit, this indicates that the washing machine door is blocked to prevent it from being opened accidentally. To

prevent any damage from occurring, wait for the symbol to switch itself off before opening the appliance door.

N.B.: if the DELAYED START function has been activated, the door cannot be opened; pauses the machine by pressing the

START/PAUSE button if you wish to open it.

! The first time the machine is switched on, you will be asked to select the language and the display will automatically show

the language selection menu.

To select the desired language press the X and Y buttons; to confirm the selection press the Z button.

If you wish to change the selected language, simultaneously press and hold all the three buttons marked with an L in the

figure, until you hear a beep. Switch the machine on again; the language selection menu will be displayed.

START/PAUSE

button with indicator

light

Running a wash cycle

1. SWITCH THE MACHINE ON. Press the button; the

text WELCOME will appear on the display and the START/

PAUSE indicator light will flash slowly in a green colour.

2. LOAD THE LAUNDRY. Open the porthole door. Load

the laundry, making sure you do not exceed the maximum

load value indicated in the table of programmes on the

following page.

3. MEASURE OUT THE DETERGENT. Pull out the

detergent dispenser drawer and pour the detergent into

the relevant compartments as described in “Detergents

and laundry”.

4. CLOSE THE DOOR.

5. SELECT THE WASH CYCLE. Press one of the WASH

CYCLE SELECTOR buttons to select the required wash

cycle; the name of the wash cycle will appear on the

display. A temperature and spin speed is set for each

wash cycle; these may be adjusted. The duration of the

cycle will appear on the display.

6. CUSTOMISE THE WASH CYCLE. Use the relevant

buttons:

Modifying the temperature and/or spin

speed. The machine automatically selects the maximum

temperature and spin speed set for the selected wash

cycle; these values cannot therefore be increased. The

temperature can be decreased by pressing the button,

until the cold wash “OFF” setting is reached. The spin

speed may be progressively reduced by pressing the

button, until it is completely excluded (the “OFF” setting).

If these buttons are pressed again, the maximum values

are restored.

Setting a delayed start.

To set a delayed start for the selected programme, press

the corresponding button repeatedly until the required

delay period has been reached. When this option is

enabled, the symbol lights up on the display. To remove

the delayed start function press the button until the text

“OFF” appears on the display.

Modifying the cycle settings.

• Press the button to enable the function; the indicator

light corresponding to the button will switch on.

• Press the button again to disable the function; the

indicator light will switch off.

! If the selected function is not compatible with the

programmed wash cycle, the indicator light will flash and

the function will not be activated.

! If the selected function is not compatible with another

function which has been selected previously, the indicator

light corresponding to the first function selected will flash

and only the second function will be activated; the indicator

light corresponding to the enabled function will remain lit.

! The functions may affect the recommended load value

and/or the duration of the cycle.

7. START THE PROGRAMME. Press the START/PAUSE

button. The corresponding indicator light will become

green, remaining lit in a fixed manner, and the door will

be locked (the DOOR LOCKED symbol will be on).

During the wash cycle, the name of the phase in progress

will appear on the display. To change a wash cycle while

it is in progress, pause the washing machine using the

START/PAUSE button (the START/PAUSE indicator light

will flash slowly in an orange colour); then select the desired

cycle and press the START/PAUSE button again.

To open the door while a cycle is in progress, press the

START/PAUSE button; if the DOOR LOCKED symbol

is switched off the door may be opened. Press the START/

PAUSE button again to restart the wash cycle from the

point at which it was interrupted.

8. THE END OF THE WASH CYCLE. This will be indicated

by the text “END OF CYCLE” on the display; when the

DOOR LOCKED symbol switches off the door may be

opened. Open the door, unload the laundry and switch off

the machine.

! If you wish to cancel a cycle which has already begun, press

and hold the button. The cycle will be stopped and the

machine will switch off.

Wash cycles and functions

Table of wash cycles

Wash cycles

Description of the wash cycle

Max.

temp.

(°C)

Max.

speed

(rpm)

Detergents

Max. load (kg)

Residual

dampness %

Energy

consumption

kWh

Total water lt

Cycle

duration

Pre-

wash

Wash

Fabric

softener

Ble-

ach

Everyday wash cycles

Cotton: extremely soiled whites. 90° 1200

  

- 7 53 2,16 72 160’

Cotton Standard 60° (1) (1° press of the button): heavily soiled whites and resistant colours. 60° 1200 -

  

7 53 1,26 52,5 190’

Cotton Standard 40° (2) (2° press of the button): lightly soiled whites and delicate colours. 40° 1200 -

  

7 53 1,09 92 185’

Cotton Standard 20° (3° press of the button): lightly soiled whites and delicate colours. 20° 1200 -

  

7 - - - 170’

Synthetics (1° press of the button): heavily soiled resistant colours. 60° 800

   

3,5 44 0,93 47 115’

Synthetics (3) (1° press of the button): lightly soiled resistant colours. 40° 800

   

3,5 44 0,57 46 100’

Synthetics (2° press of the button): lightly soiled whites and delicate colours. 40° 800

   

3,5 - - - 75’

Mix 30’ (1° press of the button): to refresh lightly soiled garments quickly (not suitable for wool,

silk and clothes which require washing by hand).

30° 800 -

 

- 3 71 0,15 35 30’

Mix 15’ (2° press of the button): to refresh lightly soiled garments quickly (not suitable for wool,

silk and clothes which require washing by hand).

30° 800 -

 

- 1,5 71 0,19 31 15’

Special cycles / Memory

Memory: allows for any wash cycle to be stored.

Baby cycle: heavily soiled delicate colours. 40° 800 -

  

3 - - - 120’

Silk/Curtains: for garments in silk and viscose, lingerie. 30° 0 -

 

- 1 - - - 55’

Wool: for wool, cashmere, etc. 40° 800 -

 

- 1,5 - - - 70’

Partial wash cycles

Spin (1° press of the button) - 1200 - - - - 7 - - - 16’

Rinse (2° press of the button) - 1200 - -

 

7 - - - 36’

Pump out (3° press of the button) - 0 - - - - 7 - - - 2’

The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to

factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.

1) Test wash cycle in compliance with directive 1061/2010: set wash cycle (1° press of the button) with a temperature of 60°C.

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be

washed at 60°C. The actual washing temperature may differ from the indicated value.

2) Test wash cycle in compliance with directive 1061/2010: set wash cycle (2° press of the button) with a temperature of 40°C.

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be

washed at 40°C. The actual washing temperature may differ from the indicated value.

For all Test Institutes:

2) Long wash cycle for cottons: set wash cycle (2° press of the button) with a temperature of 40°C.

3) Synthetic program along: set wash cycle (1° press of the button) with a temperature of 40°C.

Wash functions

Stain removal

This function is particularly useful

for the removal of stubborn

stains. Place extra compartment

4 (supplied) into compartment 1.

When pouring in the bleach, be

careful not to exceed the “max”

level marked on the central pivot

(see figure).To run the bleach cycle

on its own, pour the bleach into extra

compartment 4, set the “Rinse”

programme and activate the “Stain

removal” programme. To bleach

during a wash cycle, pour in the

detergent and any fabric softener you wish to use, set the desired wash

cycle and enable the “Stain removal” function.

! The use of extra compartment 4 excludes the “Pre-wash”

function.

! It cannot be used with the , , , Spin, Pump out, programmes.

Prewash

If this function is selected, the pre-wash cycle will run; this is

useful for removing stubborn stains.

N.B.: put the detergent in the relevant compartment.

! It cannot be used with the , , , , , , , programmes.

Extra rinse

By selecting this option, the efficiency of the rinse is increased

and optimal detergent removal is guaranteed. It is particularly

useful for sensitive skin.

! It cannot be used in conjunction with the , Spin, Pump out,

programmes.

Easy iron

By selecting this function, the wash and spin cycles will be modified in

order to reduce the formation of creases. At the end of the cycle the

washing machine will perform slow rotations of the drum; the EASY

IRON and START/PAUSE indicator lights will flash (orange) and the

text “END OF CYCLE” will appear on the display. To end the cycle,

press the START/PAUSE button or the EASY IRON button. For the

Silk/Curtains cycle, the machine will end the cycle while the laundry

is soaking; the EASY IRON and START/PAUSE indicator lights will

flash (orange) and the text “STOP WITH WATER” will appear on

the display. To drain the water so that the laundry may be removed,

press the START/PAUSE button or the EASY IRON button.

! It may not be used with the , , , programmes.

Mini load

This function is recommended for when the load of laundry is

equal to half, or less than half, of the maximum recommended

load (see Table of wash cycles).

! It cannot be used with the , , “Spin” and “Pump out”

programmes”.

Detergents and laundry

Detergent dispenser drawer

Good washing results also depend on the correct dose of

detergent: adding too much detergent will not necessa-

rily result in a more efficient wash, and may in fact cause

build up on the inside of your appliance and contribute to

environmental pollution.

! Do not use hand washing detergents because these

create too much foam.

! Use powder detergent for white cotton garments, for pre-

washing, and for washing at temperatures over 60°C.

! Follow the instructions given on the detergent packaging.

Open the detergent di-

spenser drawer and pour

in the detergent or washing

additive, as follows.

compartment 1: Pre-wash detergent (powder)

Before pouring in the detergent, make sure that extra com-

partment 4 has been removed.

compartment 2: Detergent for the wash cycle

(powder or liquid)

Liquid detergent should only be poured in immediately

prior to the start of the wash cycle.

compartment 3: Additives (fabric softeners, etc.)

The fabric softener should not overflow the grid.

extra compartment 4: Bleach

Preparing the laundry

• Divide the laundry according to:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from whites

• Empty all garment pockets and check the buttons.

• Do not exceed the values listed in the “Table of wash

cycles”, which refer to the weight of the laundry when dry.

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1200 g

1 towel 150-250 g

Special wash cycles

Cotton Standard 20°: (programme ) ideal for heavily

soiled cotton loads. The effective performance levels achieved

at cold temperatures, which are comparable to washing at

40°, are guaranteed by a mechanical action which operates

at varying speed, with repeated and frequent peaks.

Mix 30’: this wash cycle was designed to wash lightly soi-

led garments quickly: it lasts just 30 minutes and therefore

saves both energy and time. By selecting this wash cycle (

at 30°C), it is possible to wash different fabrics together

(except for wool and silk items), with a maximum load of 3 kg.

Mix 15’: this wash cycle was designed to wash lightly soiled

garments quickly: it lasts just 15 minutes and therefore saves

both energy and time. By selecting this wash cycle ( at

30°C), it is possible to wash different fabrics together (except

for wool and silk items), with a maximum load of 1.5 kg.

Baby cycle: this wash cycle can be used to remove the

soiling typically caused by babies, while ensuring that all

detergent is removed from nappies in order to prevent the

delicate skin of babies from suffering allergies. The cycle

has been designed to reduce the amount of bacteria by using

a greater quantity of water and optimising the effect of special

disinfecting additives added to the detergent.

At the end of the wash cycle, the machine will slowly rotate

the drum to prevent the formation of creases; to end the cycle

press the START/PAUSE button.

Silk: use special wash cycle to wash all silk garments.

We recommend the use of special detergent which has been

designed to wash delicate clothes.

Curtains: fold curtains and place them in a pillow case or

mesh bag. Use wash cycle .

Wool: The wool wash cycle on this Hotpoint-Ariston machine

has been tested and approved by The Woolmark Company for

washing wool garments labelled as hand washable provided

that the garments are washed according to the instructions

on the garment label and those issued by the manufacturer

of this washing machine. Hotpoint-Ariston is the first washing

machine brand to be approved by The Woolmark Company for

Apparel Care- Platinum for its washing performance and con-

sumption of energy and water. (M1126)

In UK, Eire, Hong Kong and India the Woolmark trade mark is

a Certification trade mark.

Load balancing system

Before every spin cycle, to avoid excessive vibrations and

to distribute the load in a uniform manner, the drum rotates

continuously at a speed which is slightly greater than the

washing rotation speed. If, after several attempts, the load is

not balanced correctly, the machine spins at a reduced spin

speed. If the load is excessively unbalanced, the washing ma-

chine performs the distribution process instead of spinning.

To encourage improved load distribution and balance, we

recommend small and large garments are mixed in the load.

Troubleshooting

Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure

that the problem cannot be not solved easily using the following list.

Problem:

The washing machine does not

switch on.

The wash cycle does not start.

The washing machine does not

take in water (the text “NO WATER,

CHECK SUPPLY” appears on the

display).

The washing machine continuously

takes in and

drains water.

The washing machine does not

drain or spin.

The washing machine vibrates a lot

during the spin cycle.

The washing machine leaks.

The machine is locked and the display

flashes, indicating an

error code (e.g. F-01, F-..).

There is too much foam.

Possible causes / Solutions:

• The appliance is not plugged into the socket fully, or is not making contact.

• There is no power in the house.

• The washing machine door is not closed properly.

• The ON/OFF button has not been pressed.

• The START/PAUSE button has not been pressed.

• The water tap has not been opened.

• A delayed start has been set (see “Running a wash cycle”).

• The water inlet hose is not connected to the tap.

• The hose is bent.

• The water tap has not been opened.

• There is no water supply in the house.

• The pressure is too low.

• The START/PAUSE button has not been pressed.

• The drain hose is not fitted at a height between 65 and 100 cm from the floor

(see “Installation”).

• The free end of the hose is under water (see “Installation”).

• The wall drainage system is not fitted with a breather pipe.

If the problem persists even after these checks, turn off the water tap, switch

the appliance off and contact the Assistance Service. If the dwelling is on one of

the upper floors of a building, there may be problems relating to water drainage,

causing the washing machine to fill with water and drain continuously. Special

anti-draining valves are available in shops and help to avoid this inconvenience.

• The wash cycle does not include draining: some wash cycles require the drain

phase to be started manually (see “Wash cycles and functions”).

• The EASY IRON function has been activated: To complete the wash cycle,

press the START/PAUSE button (see “Wash cycles and functions”).

• The drain hose is bent (see “Installation”).

• The drainage duct is clogged.

• The drum was not unlocked correctly during installation (see “Installation”).

• The washing machine is not level (see “Installation”).

• The washing machine is trapped between cabinets and walls (see “Installation”).

• The water inlet hose is not screwed on properly (see “Installation”).

• The detergent dispenser drawer is blocked (for cleaning instructions, see

“Care and maintenance”).

• The drain hose is not fixed properly (see “Installation”).

• Switch off the machine and unplug it, wait for approximately 1 minute and

then switch it back on again.

If the problem persists, contact the Technical Assistance Service.

• The detergent is not suitable for machine washing (it should display the text

“for washing machines” or “hand and machine wash”, or the like).

• Too much detergent was used.

Service

Before calling for Assistance:

• Check whether you can solve the problem alone (see “Troubleshooting”);

• Restart the programme to check whether the problem has been solved;

• If this is not the case, contact an authorised Technical Assistance Centre using the telephone number provided on the

guarantee certificate.

! Always request the assistance of authorised technicians.

Have the following information to hand:

• the type of problem;

• the appliance model (Mod.);

• the serial number (S/N).

This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the

front of the appliance by opening the door.

Français

Sommaire

Installation, 16-17-18-19

Déballage et mise à niveau

Raccordements eau et électricité

Premier cycle de lavage

Caractéristiques techniques

Instructions pour l’installateur

Entretien et soin, 20

Coupure de l’arrivée d’eau et du courant

Nettoyage du lave-linge

Nettoyage du tiroir à produits lessiviels.

Entretien du hublot et du tambour

Nettoyage de la pompe

Contrôle du tuyau d’arrivée de l’eau

Précautions et conseils, 21

Sécurité générale

Mise au rebut

Ouverture manuelle de la porte hublot

Description du lave-linge, 22-23

Bandeau de commandes

Écran

Comment faire un cycle de lavage, 24

Programmes et fonctions, 25

Tableau des programmes

Fonctions de lavage

Produits lessiviels et linge, 26

Tiroir à produits lessiviels

Triage du linge

Programmes spéciaux

Système d’équilibrage de la charge

Anomalies et remèdes, 27

Assistance, 28

SMLE 129

Mode d’emploi

LAVE-LINGE

Installation

! Conserver ce mode d’emploi pour pouvoir le con-

sulter à tout moment. En cas de vente, de cession ou

de déménagement, veiller à ce qu’il suive toujours le

lavante-séchante pour que son nouveau propriétaire

soit informé sur son mode de fonctionnement et

puisse profiter des conseils correspondants.

! Lire attentivement les instructions: elles fournis-

sent des conseils importants sur l’installation,

l’utilisation et la sécurité de l’appareil.

Déballage et mise à niveau

Déballage

1. Déballer le lavante-séchante.

2. Contrôler que le lavante-séchante n’a pas été

endommagé pendant le transport. S’il est abîmé,

ne pas le raccorder et contacter le vendeur.

3. Enlever les 4 vis

de protection servant

au transport, le ca-

outchouc et la cale,

placés dans la partie

arrière (voir figure).

4. Boucher les trous à l’aide des bouchons

plastique fournis.

5. Conserver toutes ces pièces: il faudra les re-

monter en cas de transport du lavante-séchante.

! Les pièces d’emballage ne sont pas des jouets

pour enfants.

Mise à niveau

1. Installer le lavante-séchante sur un sol plat

et rigide, sans l’appuyer contre des murs, des

meubles ou autre.

2. Si le sol n’est pas

parfaitement horizon-

tal, visser ou dévisser

les pieds de réglage

avant (voir figure) pour

niveler l’appareil; son

angle d’inclinaison,

mesuré sur le plan

de travail, ne doit pas

dépasser 2°.

Une bonne mise à niveau garantit la stabilité

de l’appareil et évite qu’il y ait des vibrations,

du bruit et des déplacements en cours de

fonctionnement. Si la machine est posée sur

de la moquette ou un tapis, régler les pieds de

manière à ce qu’il y ait suffisamment d’espace

pour assurer une bonne ventilation.

Raccordements eau et électricité

Raccordement du tuyau d’arrivée de l’eau

1. Reliez le tuyau d’ali-

mentation en le vissant

à un robinet d’eau froi-

de à embout fileté 3/4

gaz (voir figure).

Faire couler l’eau ju-

squ’à ce qu’elle soit

limpide et sans impure-

tés avant de raccorder.

2. Raccorder le tuyau

d’arrivée de l’eau au

lavante-séchante en le

vissant à la prise d’eau

prévue, dans la partie

arrière en haut à droite

(voir figure).

3. Attention à ce que le tuyau ne soit pas plié

ou écrasé.

! La pression de l’eau doit être comprise entre

les valeurs indiquées dans le tableau des Ca-

ractéristiques techniques (voir page ci-contre).

! Si la longueur du tuyau d’alimentation ne suffit

pas, s’adresser à un magasin spécialisé ou à un

technicien agréé.

! N’utiliser que des tuyaux neufs.

! Utiliser ceux qui sont fournis avec l’appareil.

65 - 100 cm

Raccordement du tuyau de vidange

Raccorder le tuyau

d’évacuation, sans

le plier, à un conduit

d’évacuation ou à une

évacuation murale pla-

cés à une distance du

sol comprise entre 65

et 100 cm;

ou bien l’accrocher à

un évier ou à une bai-

gnoire, dans ce cas,

fixer le support en pla-

stique fourni avec l’ap-

pareil au robinet (voir

figure). L’extrémité libre

du tuyau d’évacuation

ne doit pas être plon-

gée dans l’eau.

! L’utilisation d’un tuyau de rallonge est abso-

lument déconseillée mais si on ne peut faire

autrement, il faut absolument qu’il ait le même

diamètre que le tuyau original et sa longueur ne

doit pas dépasser 150 cm.

Branchement électrique

Avant de brancher la fiche dans la prise de cou-

rant, s’assurer que:

• la prise est bien reliée à la terre et est conforme

aux réglementations en vigueur;

• la prise est bien apte à supporter la puissance

maximale de l’appareil indiquée dans le tableau

des Caractéristiques techniques (voir ci-contre);

• la tension d’alimentation est bien comprise

entre les valeurs figurant dans le tableau des

Caractéristiques techniques (voir ci-contre);

• la prise est bien compatible avec la fiche du

lavante-séchante. Autrement, remplacer la

prise ou la fiche.

! Le lavante-séchante ne doit pas être installé

dehors, même à l’abri, car il est très dangereux

de le laisser exposé à la pluie et aux orages.

! Après installation du lavante-séchante, la prise

de courant doit être facilement accessible.

! N’utiliser ni rallonges ni prises multiples.

! Le câble ne doit être ni plié ni trop écrasé.

! Le câble d’alimentation ne doit être remplacé

que par des techniciens agréés.

Attention! Nous déclinons toute responsabilité en cas

de non-respect des normes énumérées ci-dessus.

Premier cycle de lavage

Avant la première mise en service de l’appareil, ef-

fectuer un cycle de lavage avec un produit lessiviel

mais sans linge et sélectionner le programme .

Caractéristiques techniques

Modèle

SMLE 129

Dimensions

largeur 59,5 cm

hauteur 81,5 cm

profondeur 54,5 cm

Capacité

de 1 à 7 kg

Raccorde-

ments élec-

triques

Voir la plaque signalétique

appliquée sur la machine

Raccor-

dements

hydrauli-

ques

pression maximale 1 MPa

(10 bar) pression minimale

0,05 MPa (0,5 bar) capacité

du tambour 52 litres

Vitesse

d’essorage

jusqu’à 1200 tours minute

Programmes

de contrôle

selon les

directives

1061/2010

1015/2010.

programme

; (1° pres-

sion de la touche); Coton

standard 60°C.

programme ; (2° pres-

sion de la touche); Coton

standard 40°C.

Cet appareil est conforme

aux Directives Communau-

taires suivantes:

- 2004/108/CE (Compatibili-

té électromagnétique)

- 2006/95/CE (Basse Tension)

- 2002/96/CE

Instructions pour l’installateur

Application du panneau d’habillage en

bois sur la porte et montage du machine

à laver à l’intérieur des éléments:

Au cas où, après le montage du panneau en bois,

il faudrait expédier la machine pour son installation

finale, nous vous conseillons de la laisser dans

son emballage d’origine. L’emballage a été juste-

ment réalisé de manière à permettre le montage

du panneau en bois sur la machine sans déballer

complètement le produit (voir figures ci-dessous).

Le panneau en bois couvrant la façade ne doit

pas avoir plus de 18 mm d’épaisseur, il peut être

articulé tant à droite qu’à gauche. Pour plus de

facilité d’emploi, nous conseillons d’adopter le

même sens d’ouverture que pour le hublot dont

les charnières sont montées sur le côté gauche.

Tur seite

Accessoires montage porte (Fig.1-2-3-4-5).

Fig. 1

N°2 Charnière

N°1 Aimant N°1 Butoir aimant

N°1 Cheville en

caoutchouc

N°2 Supports charnière

N°4 Cales

Fig. 2

Fig. 3 Fig. 4

Fig. 5

Fig. 4/B

- 6 vis autotaraudeuses l = 13 mm “type A”.

- 2 vis métriques à tête évasée l = 25 mm “type

B”; pour fixation du butoir aimant au meuble.

- 4 vis métriques l = 15 mm “type C”; pour

montage des supports charnière au meuble.

- 4 vis métriques l = 7 mm “type D”; pour mon-

tage des charnières aux supports.

Montage des pièces sur la façade de la

machine.

- Montez les supports de la charnière sur la faça-

de, en positionnant le trou indiqué par une flèche

dans la fig. 1 vers l’intérieur de la façade et inter-

posez une cale (fig. 4/B). Utilisez les vis type C.

- Montez le butoir aimant du côté opposé en

haut et interposez deux cales (fig. 4/B). Utilisez

les deux vis type B.

Utilisation du gabarit de forage.

- Pour marquer l’emplacement des trous sur le

côté du panneau, alignez le gabarit de perçage

avec le côté supérieur gauche du panneau en vous

servant des lignes tracées aux extrémités.

- Pour marquer l’emplacement des trous sur le

côté droit du panneau, alignez le gabarit de perça-

ge avec le côté supérieur droit du panneau.

- Réalisez à l’aide d’une fraise appropriée les quatre

emplace-ments où devront trouver place les deux

charnières, la cheville en caoutchouc et l’aimant.

Montage des pièces sur le panneau en

bois (Porte).

- Montez les charnières aux emplacements prévus (la

partie mobile de la charnière doit se trouver vers l’ex-

térieur du panneau) et fixez-les à l’aide de 4 vis type A.

- Montez l’aimant à son emplacement en haut,

à l’opposé des charnières et fixez-le au moyen

de deux vis type B.

- Montez la cheville en caoutchouc à sa place en bas.

Le panneau est à présent prêt, vous pouvez le

monter sur la machine.

Montage du panneau sur la machine.

Introduisez l’ergot de la charnière indiqué par la

flèche fig. 2 dans le logement du support charnière,

poussez le panneau vers la façade de la machine et

fixez les deux charnières à l’aide des deux vis type D.

Fixation du support de la base.

Si la machine est installée à une extrémité de la

cuisine intégrée, montez une ou les deux glissières

du socle comme illustré fig. 8 en réglant leur pro-

fondeur en fonction de la position du socle et, au

besoin, fixez-le à ces dernières fig. 9. Pour monter

le support de la base, procédez comme suit (fig.

8): Fixez l’équerre P à l’aide de la vis R, insérez le

support de la base Q dans la fente prévue et après

l’avoir dûment positionné bloquez-le à l’aide de

l’équerre d’assemblage P et de la vis R.

Montage de la machine à l’intérieur des

éléments.

- Poussez la machine à travers l’ouverture en

l’alignant aux autres meubles (fig. 6).

- Servez-vous des pieds de réglage pour amener

la machine à la hauteur désirée.

- Pour régler la position du panneau en bois à la

verticale et à l’horizontale, servez-vous des vis C et

D comme illustré fig. 7.

Important: fermez la partie inférieure de la faça-

de, la base touchant au sol.

Fig. 8 Fig. 9

Accessoires fournis pour le réglage de la

hauteur.

Vous trouverez à l’intérieur du couvercle en polysty-

rène (fig. 10): 2 traverses (G); 1 listel (M);

et à l’intérieur du tambour :

4 pieds supplémentaires

(H),

4 vis (I),

4 vis (R),

4 écrous (L),

2 supports pour la base (Q)

Réglage de la machine en hauteur.

La machine peut être réglée en hauteur (de 815

mm à 835 mm) à l’aide de ses 4 pieds.

Si vous souhaitez l’amener à une hauteur supé-

rieure à celle qui est indiquée plus haut, c’est à dire

jusqu’à 870 mm, utilisez les accessoires suivants :

les 2 traverses (G); les 4 pieds (H); les 4 vis (I); les

4 écrous (L) puis procédez comme suit (fig. 11):

démontez les 4 pieds originaux, positionnez une

traverse G dans la partie avant de la machine,

fixez-la à l’aide des vis I (en les vissant dans les

trous où étaient fixés les pieds originaux) puis

montez les nouveaux pieds H.

Procédez de même dans la partie arrière de la

machine.

Vous pouvez alors régler les pieds H pour élever

ou abaisser la machine de 835 mm à 870 mm.

Après avoir atteint la hauteur désirée, bloquez les

écrous L à la traverse G.

Pour régler la machine à une hauteur comprise

entre 870 mm et 900 mm, montez le listel M et

réglez les pieds H jusqu’à la hauteur souhaitée.

Pour monter le listel, procédez comme suit:

desserrez les trois vis N situées dans la partie avant

du couvercle, montez le listel M comme illustré

fig. 12 et serrez les vis N.

570

min

815

540

595

820 ÷ 900

600 min

Fig. 6 Fig. 7

Fig. 11 Fig. 12

Fig. 10

Entretien et soin

Coupure de l’arrivée d’eau et du

courant

• Fermer le robinet de l’eau après chaque lavage.

Cela réduit l’usure de l’installation hydraulique

du lavante-séchante et évite tout danger de

fuites.

• Débrancher la fiche de la prise de courant

lors de tout nettoyage du lavante-séchante et

pendant tous les travaux d’entretien.

Nettoyage du lavante-séchante

Pour nettoyer l’extérieur et les parties en caout-

chouc, utiliser un chiffon imbibé d’eau tiède et

de savon. N’utiliser ni solvants ni abrasifs.

Nettoyage du tiroir à produits les-

siviels.

Soulever le tiroir et le

tirer vers soi pour le

sortir de son logement

(voir figure).

Le laver à l’eau cou-

rante; effectuer cette

opération assez sou-

vent.

Entretien du hublot et du tambour

• Il faut toujours laisser le hublot entrouvert pour

éviter la formation de mauvaise odeurs.

Nettoyage de la pompe

Le lavante-séchante est équipé d’une pompe

autonettoyante qui n’exige aucune opération

d’entretien. Il peut toutefois arriver que de menus

objets (pièces de monnaie, boutons) tombent

dans la préchambre qui protège la pompe, pla-

cée en bas de cette dernière.

! S’assurer que le cycle de lavage est bien ter-

miné et débrancher la fiche.

Pour accéder à cette préchambre:

1. dévisser le cou-

vercle en le tournant

dans le sens inverse

des aiguilles d’une

montre (voir figure): il

est normal qu’un peu

d’eau s’écoule;

2. nettoyer soigneusement l’intérieur;

3. revisser le couvercle;

Contrôle du tuyau d’arrivée de l’eau

Contrôler le tuyau d’alimentation au moins une

fois par an. Procéder à son remplacement en cas

de craquèlements et de fissures: car les fortes

pressions subies pendant le lavage pourraient

provoquer des cassures.

! N’utiliser que des tuyaux neufs.

La pagina sta caricando ...

Scholtes SMLE 129 Instructions For Use Manual

Marca: Scholtes

Modello: SMLE 129

Categoria: Lavatrici

Tipo: Instructions For Use Manual

Scarica il pdf

rapporto

in altre lingue

English: Scholtes SMLE 129
français: Scholtes SMLE 129
español: Scholtes SMLE 129

Scholtes SMLE 129 Instructions For Use Manual

Scholtes SMLE 129 Instructions For Use Manual

in altre lingue

Documenti correlati

Altri documenti