Yamaha IMX644 Manuale utente

Marca: Yamaha

Modello: IMX644

Categoria: Controller DJ

Tipo: Manuale utente

Owner's Manual

LST0803-001B 008AP-02B0

U.R.G., Pro Audio Division

Yamaha Pro Audio global web site:

http://www.yamahaproaudio.com/

Yamaha Manual Library

http://www.yamaha.co.jp/manual/

The above warning is located on the top of the unit.

Explanation of Graphical Symbols

The lightning ﬂash with arrowhead symbol

within an equilateral triangle is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufﬁcient magnitude

to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the product.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as

radiators, heat registers, stoves, or other apparatus

(including ampliﬁers) that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two

blades with one wider than the other. A grounding

type plug has two blades and a third grounding

prong. The wide blade or the third prong are provided

for your safety. If the provided plug does not ﬁt into

your outlet, consult an electrician for replacement of

the obsolete outlet.

10 Protect the power cord from being walked on or

pinched particularly at plugs, convenience

receptacles, and the point where they exit from the

apparatus.

11 Only use attachments/accessories speciﬁed by the

manufacturer.

12 Use only with the cart, stand,

tripod, bracket, or table

speciﬁed by the manufacturer,

or sold with the apparatus.

When a cart is used, use

caution when moving the cart/

apparatus combination to

avoid injury from tip-over.

13 Unplug this apparatus during lightning storms or

when unused for long periods of time.

14 Refer all servicing to qualiﬁed service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has

been exposed to rain or moisture, does not operate

normally, or has been dropped.

(UL60065_03)

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions con-

tained in this manual, meets FCC requirements. Modiﬁcations not

expressly approved by Yamaha may void your authority, granted by

the FCC, to use the product.

2. IMPORTANT:

When connecting this product to accessories and/

or another product use only high quality shielded cables. Cable/s

supplied with this product MUST be used. Follow all installation

instructions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE:

This product has been tested and found to comply with the

requirements listed in FCC Regulations, Part 15 for Class “B” digital

devices. Compliance with these requirements provides a reason-

able level of assurance that your use of this product in a residential

environment will not result in harmful interference with other elec-

tronic devices. This equipment generates/uses radio frequencies

and, if not installed and used according to the instructions found in

the users manual, may cause interference harmful to the operation

of other electronic devices. Compliance with FCC regulations does

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

not guarantee that interference will not occur in all installations. If

this product is found to be the source of interference, which can be

determined by turning the unit “OFF” and “ON”, please try to elimi-

nate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by

the interference.

Utilize power outlets that are on different branch (circuit breaker or

fuse) circuits or install AC line ﬁlter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change the

lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type of

product. If you can not locate the appropriate retailer, please con-

tact Yamaha Corporation of America, Electronic Service Division,

6600 Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed by

Yamaha Corporation of America or its subsidiaries.

FCC INFORMATION (U.S.A.)

(5)-6

1/2

IMX644 Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical

shock, short-circuiting, damages, ﬁre or other hazards. These precautions include, but are not limited to, the following:

• Only use the voltage speciﬁed as correct for the device. The required voltage is

printed on the name plate of the device.

• Use only the included power cord.

If you intend to use the device in an area other than in the one you purchased,

the included power cord may not be compatible. Please check with your Yamaha

dealer.

• Do not place the power cord near heat sources such as heaters or radiators, and

do not excessively bend or otherwise damage the cord, place heavy objects on

it, or place it in a position where anyone could walk on, trip over, or roll anything

over it.

• Be sure to connect to an appropriate outlet with a protective grounding

connection. Improper grounding can result in electrical shock.

• Do not open the device or attempt to disassemble the internal parts or modify

them in any way. The device contains no user-serviceable parts. If it should

appear to be malfunctioning, discontinue use immediately and have it inspected

by qualiﬁed Yamaha service personnel.

• Do not expose the device to dripping or splashing, use it near water or in damp

or wet conditions, or place containers on it containing liquids which might spill

into any openings. If any liquid such as water seeps into the device, turn off the

power immediately and unplug the power cord from the AC outlet. Then have

the device inspected by qualiﬁed Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

• If the power cord or plug becomes frayed or damaged, or if there is a sudden

loss of sound during use of the device, or if any unusual smells or smoke

should appear to be caused by it, immediately turn off the power switch,

disconnect the electric plug from the outlet, and have the device inspected by

qualiﬁed Yamaha service personnel.

• If this device should be dropped or damaged, immediately turn off the power

switch, disconnect the electric plug from the outlet, and have the device

inspected by qualiﬁed Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage

to the device or other property. These precautions include, but are not limited to, the following:

• Remove the electric plug from the outlet when the device is not to be used for

extended periods of time, or during electrical storms.

• When removing the electric plug from the device or an outlet, always hold the

plug itself and not the cord. Pulling by the cord can damage it.

• Before moving the device, remove all connected cables.

• When setting up the devices, make sure that the power switch can be easily

turned ON/OFF. If some trouble or malfunction occurs, immediately turn off the

power switch and disconnect the plug from the outlet.

• If the device is mounted in an EIA standard rack, carefully read the section

“Precautions for Rack Mounting” on page 7. Inadequate ventilation can result in

overheating, possibly causing damage to the device(s), malfunction, or even

ﬁre.

•Avoid setting all equalizer controls and faders to their maximum. Depending on

the condition of the connected devices, doing so may cause feedback and may

damage the speakers.

• Do not expose the device to excessive dust or vibrations, or extreme cold or heat

(such as in direct sunlight, near a heater, or in a car during the day) to prevent

the possibility of panel disﬁguration or damage to the internal components.

• Do not place the device in an unstable position where it might accidentally fall

over.

• Do not block the vents. This device has ventilation holes at the sides to prevent

the internal temperature from becoming too high. In particular, do not place the

device on its side or upside down. Inadequate ventilation can result in

overheating, possibly causing damage to the device(s), or even ﬁre.

• Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile

phone, or other electric devices. Doing so may result in noise, both in the device

itself and in the TV or radio next to it.

Power supply/Power cord

Do not open

Water warning

If you notice any abnormality

Power supply/Power cord

Location

(5)-6

2/2

IMX644 Owner’s Manual

• Before connecting the device to other devices, turn off the power for all devices.

Before turning the power on or off for all devices, set all volume levels to

minimum.

• The included power cable has a three-conductor plug, so if the AC outlet is

grounded the IMX644 will be grounded appropriately.

• When turning on the AC power in your audio system, always turn on the power

ampliﬁer LAST, to avoid speaker damage. When turning the power off, the power

ampliﬁer should be turned off FIRST for the same reason.

• Condensation can occur in the device due to rapid, drastic changes in ambient

temperature – when the device is moved from one location to another, or air

conditioning is turned on or off, for example. Using the device while

condensation is present can cause damage. If there is reason to believe that

condensation might have occurred, leave the device for several hours without

turning on the power until the condensation has completely dried out.

• Do not insert your ﬁngers or hands in any gaps or openings on the device

(ports, etc.).

•Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into any

gaps or openings on the device (ports, etc.) If this happens, turn off the power

immediately and unplug the power cord from the AC outlet. Then have the

device inspected by qualiﬁed Yamaha service personnel.

• Do not apply oil, grease, or contact cleaner to the faders. Doing so may cause

problems with electrical contact or fader motion.

• Do not rest your weight on the device or place heavy objects on it, and avoid use

excessive force on the buttons, switches or connectors.

Always turn the power off when the device is not in use.

The performance of components with moving contacts, such as switches, volume controls, and connectors, deteriorates over time. Consult qualiﬁed Yamaha service

personnel about replacing defective components.

SPECIAL NOTICES

• The illustrations as shown in this manual are for instructional purposes only, and may appear somewhat different from those on your device.

• The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.

• Speciﬁcations and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or speciﬁcations

at any time without prior notice. Since speciﬁcations, equipment or options may not be the same in every locale, please check with your Yamaha dealer.

Connections Handling caution

Yamaha cannot be held responsible for damage caused by improper use or modiﬁcations to the device, or data that is lost or destroyed.

European models

Purchaser/User Information speciﬁed in EN55103-1 and EN55103-2.

Inrush Current: 10 A

Conforms to Environments: E1, E2 E3 and E4

* This applies only to products distributed by

YAMAHA CORPORATION OF AMERICA.

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620

Telephone : 714-522-9011

Type of Equipment : DIGITAL INSTALLATION MIXER

Model Name : IMX644

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interfer-

ence that may cause undesired operation.

See user manual instructions if interference to radio reception is sus-

pected.

(FCC DoC)

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

WARNING:

THIS APPARATUS MUST BE EARTHED

IMPORTANT. The wires in this mains lead are coloured in accor-

dance with the following code:

GREEN-AND-YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus may

not correspond with the coloured markings identifying the terminals

in your plug proceed as follows:

The wire which is coloured GREEN-and-YELLOW must be con-

nected to the terminal in the plug which is marked by the letter E or

by the safety earth symbol or colored GREEN or GREEN-and-

YELLOW.

The wire which is coloured BLUE must be connected to the terminal

which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the termi-

nal which is marked with the letter L or coloured RED.

• This applies only to products distributed by Yamaha Music U.K. Ltd. (3 wires)

IMX644 Owner’s Manual

Table of contents

Introduction

Features ............................................................................... 6

Precautions for Rack Mounting ............................................ 7

Before Operation .................................................................. 7

Acquiring the IMX644 Manager Software and Manuals ....... 7

Controls and Functions

Front Panel ........................................................................... 8

Rear Panel.......................................................................... 10

Connections

System Example................................................................. 12

Connectors and Cables ...................................................... 13

Mix Functions

Input Channels ................................................................... 15

Output Channels................................................................. 17

Others................................................................................. 17

Appendix

Troubleshooting.................................................................. 18

Memory Initialization........................................................... 18

IMX644 Status List ............................................................. 19

Remote Control Protocol Specifications ............................. 20

General Specifications........................................................ 21

Input/output Characteristics................................................ 21

Electrical Characteristics .................................................... 22

GPI Circuit Example ........................................................... 23

Dimensions......................................................................... 24

Block Diagram .................................................................... 25

IMX644 Owner’s Manual

Introduction

Thank you for purchasing the Yamaha IMX644 Digital Installation Mixer. In order to take full

advantage of the IMX644 functionality and to ensure trouble-free operation, please read this

owner’s manual carefully before use. After you have read the manual, keep it in a safe place

for reference when needed.

■

Versatile Input/Output Conﬁguration

The IMX644 features an input/output configuration that is ideal

for a wide range of applications: six mono inputs, four stereo in-

puts, two stereo outputs, two mono outputs, and one dedicated

stereo output for recording.

■

16 Memories

Up to 16 sets of mixer settings can be stored in memory and in-

stantly recalled as required. Four of the memories can be directly

recalled via front-panel MEMORY [A] through [D] buttons.

■

Optical Digital I/O

Connecting to compatible devices (CD and DVD players, for ex-

ample) via the optical digital interface allows accurate signal

transfer with no loss of signal quality. The digital input features

a built-in sample rate converter, so there is no need for word

clock synchronization.

■

Powerful Mixing Features

•Parametric EQ

Parametric equalization is provided on all input channels: 3-

band EQ on mono input channels, and 2-band EQ on stereo

input channels.

6-band EQ is provided on all outputs except the recording

output.

• Feedback Suppressor

Feedback suppression is provided on all six mono input

channels.

The Feedback Suppressor provides two stages of feedback

prevention: static ﬁlters that can be set in advance, and

dynamic ﬁlters that self-adjust in real time to control feed-

back.

• Priority for Speciﬁed Voice or Music Sources

The Priority Ducker automatically “ducks” (reduces the vol-

ume of) the background when a signal is applied to a speci-

ﬁed mono input channel, making announcements stand out

for greater intelligibility. All stereo inputs assigned to the

same output channel are reduced to a speciﬁed level when

priority input is detected.

Music Override gives priority to a music source applied to a

speciﬁed stereo input channel. All other stereo inputs

assigned to the same output channel are muted when prior-

ity input is detected.

• Delay

Precise delays can be applied to all outputs to allow time

alignment for a solid sonic image with clear imaging and

optimum overall sound quality throughout the listening

area.

Features

Accessories

•AC power cord

• Rubber feet x 4

• Euroblock plug (3P) x 12

• Owner’s Manual (this document)

Introduction

IMX644 Owner’s Manual

This unit will operate stably in an environmental temperature of

0–40˚C. If you install this device together with multiple units of

the same device or other devices in an EIA standard rack, the

heat produced by the various devices may raise the ambient tem-

perature inside the rack, resulting in inefficient performance. To

ensure that the heat produced by this device can be dissipated ap-

propriately, please ensure the following conditions when rack-

mounting it.

• If multiple units are mounted in the same rack, leave a 1U

rack space between every two units. Also either leave the

open spaces uncovered or install appropriate ventilating

panels to minimize the possibility of heat buildup.

• When mounting this device together with other heat-pro-

ducing equipment such as power ampliﬁers, leave 1U or

more space between it and other devices. Install a ventila-

tion panel in this vacant space or leave it open to ensure ade-

quate cooling.

•To ensure sufﬁcient airﬂow, leave the rear of the rack open

and position it at least 10 centimeters from walls or other

surfaces. If the rear of the rack can’t be left open, install a

commercially available fan or similar ventilating option to

secure sufﬁcient airﬂow. If you’ve installed a fan kit, there

may be cases in which closing the rear of the rack will pro-

duce a greater cooling effect. Refer to the rack and/or fan

unit manual for details.

■

Connecting the AC Power Cable

CAUTION

• Before connecting the power cable, make sure that the power

switches of all devices are turned OFF.

First connect the supplied power cable to the [AC IN] socket on

the rear panel of the IMX644, then connect the AC plug to an ap-

propriate AC power outlet (make sure the local supply voltage

matches the rated AC voltage of the unit).

■

Powering ON or OFF

CAUTION

•To prevent loud noise bursts from the speakers when power-

ing up the system, turn devices ON in the following order:

audio sources (microphones, CD players, etc.), IMX644, and

ﬁnally power ampliﬁers. Reverse this order when turning the

system off.

Press the [ON] end of the [POWER] switch to

turn the unit ON.

Press the [OFF] end of the [POWER] switch to

turn the unit OFF.

CAUTION

• Rapidly turning the unit ON and OFF in succession can

cause it to malfunction. After turning the unit OFF, wait for

more than 6 seconds before turning it ON again.

The information in this manual deals primarily with setting up

and operating the IMX644 hardware.

For detailed parameter control the IMX644 Manager software

application is required. The IMX644 Manager software and

manuals can be downloaded from Yamaha’s professional audio

website (URL below).

http://www.yamahaproaudio.com/

The available IMX644 Manager documents are as follows:

• IMX644 Manager Owner’s Manual

This manual contains detailed information relating to the

IMX644 unit and IMX644 Manager software.

Precautions for Rack

Mounting

Before Operation

Acquiring the IMX644

Manager Software and

Manuals

IMX644 Owner’s Manual

Controls and Functions

[LOCK] Switch and Indicator

The [LOCK] switch can be used to “lock” the panel level knobs

(5, 8, and 11), making them inoperable and preventing acciden-

tal changes. After setting levels and/or recalling a memory as re-

quired, press the [LOCK] switch with a thin object (such as the

tip of a pen) to prevent further changes to the level settings. The

LOCK indicator lights red when the controls are locked.

Press the [LOCK] switch a second time to unlock the controls

and allow normal operation of the level knobs.

NOTE

• The LOCK buttons in the IMX644 Manager application

INPUT display can be used to enable independent operation

of each panel level control.

• If the settings of the level knobs have been increased since

the [LOCK] switch was engaged, the settings at the time the

[LOCK] switch was engaged will be retained when it is

disengaged. In order to increase a level setting after

disengaging the [LOCK] switch in such a case it is necessary

to lower the setting of the knob to the point at which it was

locked, and then raise the level as required.

• When the power is turned ON, the MEMORY number that

was active when the power was turned OFF is recalled. Save

the memory using the IMX644 Manager application before

engaging the [LOCK] switch.

• The LOCK function is temporarily disengaged when the

IMX644 Manager application goes online. The LOCK

function will be re-engaged if the unit is restarted, so don’t

operate the [LOCK] switch while the IMX644 Manager is

online.

[USB] Connector

The computer running the IMX644 Manager application can be

connected to the IMX644 via this connector. The [USB] connec-

tor cannot be used at the same time as the rear-panel [REMOTE]

connector.

Front Panel

578 !42 #

69)@

Precautions when using the [USB] connector

When connecting the computer to the [USB] connector,

make sure to observe the following points. Failing to do so

risks freezing the computer and corrupting or losing the data.

If the computer or the device freezes, restart the application

software or the computer OS, or turn the power to the device

off then on again.

CAUTION

• Use an AB type USB cable of less than about 3 meters.

• Before connecting the computer to the [USB] connector,

exit from any power-saving mode of the computer (such

as suspend, sleep, standby).

• Before turning on the power to the device, connect the

computer to the [USB] connector.

•Execute the following before turning the power to the

device on/off or plugging/unplugging the USB cable to/

from the [USB] connector.

- Quit any open application software on the computer.

- Make sure that data is not being transmitted from the

device.

• While the computer is connected to the device, you

should wait for six seconds or more between these

operations: (1) when turning the power of the device off

then on again, or (2) when alternately connecting/

disconnecting the USB cable.

Controls and Functions

IMX644 Owner’s Manual

■

MONO INPUT Section

Matrix Indicators

The outputs to which each mono input are assigned are displayed

by orange indicators.

[SIGNAL/PEAK] Indicators

These indicators light green when a signal is detected at the cor-

responding mono input.

The [SIGNAL/PEAK] indicators also light red to indicate exces-

sive input level at the corresponding input. If excessive input

level is indicated either reduce the output level of the connected

source, or reduce the IMX644 input sensitivity via the appropri-

ate rear-panel [PAD] switch or by reducing the [INPUT GAIN]

setting via the IMX644 Manager application.

Level Knobs

These knobs adjust the input level of the corresponding mono

channels.

■

STEREO INPUT Section

Matrix Indicators

The outputs to which each stereo input are assigned are dis-

played by orange indicators.

[SIGNAL/PEAK] Indicators

These indicators light green when a signal is detected at the cor-

responding stereo input.

The [SIGNAL/PEAK] indicators also light red to indicate exces-

sive input level at the corresponding input. If excessive input

level is indicated, reduce the output level of the connected

source.

NOTE

• The [SIGNAL/PEAK] indicator may light red when certain

types of signals are received via the OPTICAL input, but in

such cases the signal is within range and no further adjust-

ments are required.

Level Knobs

These knobs adjust the input level of the corresponding stereo

channels.

■

OUTPUT Section

Level Meter

Displays the levels of the signal being output via OUTPUT 1 and

If the PEAK indicator lights the output level is too high. If exces-

sively high output levels are indicated, reduce the input and/or

output levels as required.

NOTE

• The signals OUTPUT 1 and 2 are both stereo pairs, so each

level meter indicates the output level of the mixed L and R

signal.

)

[SIGNAL/PEAK] Indicators

These indicators light green when a signal is detected at

OUTPUT 3 and 4.

The [SIGNAL/PEAK] indicators also light red to indicate exces-

sive output level at the corresponding output. If excessive output

level is indicated, reduce the input level or output level.

! Level Knobs

These knobs adjust the output level from the corresponding out-

put channels.

@ MEMORY [A] – [D] Buttons

• Recalling Memories

To recall a memory press and hold one of the MEMORY

buttons for about 2 seconds – the button’s indicator will

light and the mix settings assigned to that memory will be

recalled.

Settings are stored in the IMX644 memories via the

IMX644 Manager application. Memories A through D all

contain the same settings when the unit is initially shipped

from the factory.

• Switching Modes

To start the unit in IMX644 Manager mode, hold the MEM-

ORY [D] button while turning the [POWER] switch ON.

The unit starts up in the “normal” mode if the power is

turned on while the MEMORY [D] button is not held.

# [POWER] Switch & Indicator

Turns power to the unit ON or OFF. The indicator lights green

when the power is ON.

NOTE

• Since the level settings for each channel are stored in the

IMX644 unit itself, be sure that the IMX644 Manager applica-

tion is online when setting up the memories.

IMX644

Manager Mode

This mode allows communication with

the IMX644 application. Communica-

tion with AMX and similar external

controllers cannot occur in this mode.

Normal Mode

This is the unit’s normal operating

mode. Communication with AMX and

similar external controllers is also pos-

sible in this mode. Communication

with the IMX644 Manager application

is not possible in this mode.

Controls and Functions

10 IMX644 Owner’s Manual

NOTE

• Refer to “Connectors and Cables” on page 13 for details on connectors and cables for use with the IMX644.

1 [AC IN] Connector

Connect the supplied AC cable here.

First connect the AC cable to the IMX644, then plug it into an

appropriate AC outlet.

2 Earth Screw

For maximum safety, please earth the unit properly. The sup-

plied AC power cable is a 3-wire type, so if the AC outlet used

is properly earthed the IMX644 will be earthed as well. Hum and

interference may by further reduced in some cases by also con-

necting the earth screw to an earth point.

3 [REMOTE] Connector

This RS-232C connector allows communication with a comput-

er running the IMX644 Manager application or external control-

lers.

The [REMOTE] connector cannot be used simultaneously with

the front-panel [USB] connector. If both connectors are connect-

ed, the front-panel [USB] connector takes priority.

4 [GPI] Connector

This 25-pin D-sub GPI (General Purpose Interface) connector

provides eight input ports and eight output ports for a variety of

control signals, plus one dedicated output port that indicates the

unit’s power ON/OFF status.

■ STEREO INPUT Section

5 L/R Connectors 1, 2, 3, 4A, and OPTICAL 4B

The output from CD players and other stereo line-level sources

can be connected to these stereo inputs.

NOTE

• The 4A (L/R) connectors and 4B (OPTICAL) connector can-

not be used simultaneously.

■ REC OUT Section

6 L/R Connectors A and OPTICAL B

A CD recorder or other stereo recorder can be connected here.

NOTE

•A feedback loop can occur if a CD recorder or similar device

is connected to both a STEREO INPUT and the REC OUT

connectors. In such cases use the IMX644 Manager applica-

tion MATRIX controls to turn the OUTPUT channel to REC

OUT connector assignment off.

■ MONO INPUT Section

7 Euroblock Connectors

Microphones and similar mono sources can be connected to

these balanced input connectors. High-quality head amplifiers

are built in. Refer to page 13 for instructions on connecting to the

Euroblock connectors.

8 [PAD] Switches

When ON, input to the corresponding mono channel is attenuat-

ed by 34 dB. The pads are ideal for matching input sensitivity to

the output from wireless microphone tuners and similar high-

output source devices.

Rear Panel

246)

35 7 89

Controls and Functions

IMX644 Owner’s Manual 11

9 [+48V] Switch

When ON, 48V phantom power is applied to the corresponding

mono input. Turn the [+48V] switch ON for channels to which

phantom-powered condenser microphones or other devices that

require phantom power are connected.

CAUTION

• Make sure that phantom power is turned OFF unless it is

needed.

• When turning phantom power ON, make sure that no

equipment other than phantom-powered devices such

condenser microphones are connected to the corresponding

MONO INPUT connectors. Applying phantom power to a

device that does not require phantom power can damage the

device.

• Do not connect or disconnect a device to a MONO INPUT

while phantom power is applied. Doing so can damage the

connected device and/or the unit itself.

• Make sure that the system’s power ampliﬁers and/or powered

speakers are turned OFF while turning phantom power ON

or OFF to prevent damage to the speakers. We also

recommend setting all level controls to minimum level. If

these measures are not observed sudden high-level noise

bursts can potentially damage equipment and even the

hearing of people in the area.

■ OUTPUT Section

) Euroblock Connectors

These balanced output connectors are for connection to power

amplifiers and other output devices.

OUTPUT 1 and 2 are stereo outputs. The A connector outputs

the left-channel signal, and the B connector outputs the right-

channel signal. OUTPUT 1 and 2 can also be assigned for mono

output via the IMX644 Manager application.

OUTPUT 3 and 4 are mono outputs. Refer to page 13 for instruc-

tions on connecting to the Euroblock connectors.

12 IMX644 Owner’s Manual

Connections

System Example

1 2 3 4

5 6 7 8

Computer

CD recorder

Power ampliﬁer

External control input/

output device

AMX or similar external

controller

Microphone

Cassette deck

MD player

Wireless tuner

Wireless microphone

Zone 3 speakers

Zone 4 speakers

Zone 1

speakers

Zone 2

speakers

Connections

IMX644 Owner’s Manual 13

■ [MONO INPUT] and [OUTPUT] Con-

nectors (3-pin Euroblock)

Connect external microphones, amplifiers and other devices to

the rear-panel [MONO INPUT] and [OUTPUT] connectors via

cables fitted with the supplied 3-pin Euroblock plugs.

Follow the procedure outlined in this section to attach the Eurob-

lock plugs to the appropriate cables.

Use balanced lines to connect microphones and similar sources

to the [MONO INPUT] connectors. Wire balanced cables as

shown in the diagram below.

When an amplifier to be connected to the OUTPUT connector

has balanced XLR type inputs, wire the connection cable as

shown in the diagram below.

Euroblock Plug Connection

Use the included Euroblock plug (3P) to make connections to the

[MONO INPUT] and [OUTPUT] connectors.

1 Loosen the terminal screws.

NOTE

•A “minus” type screwdriver with a blade width of approxi-

mately 3 millimeters is recommended for Euroblock connec-

tor attachment.

2 Insert the cables.

Connectors and Cables

123

Euroblock Pin Assignments

Pin No.

Signal

name

1HOT

2 COLD

3 GND

XLR-3-11C (or equivalent)

XLR-3-12C (or equivalent)

● Cable preparation

•To prepare the cable for

attachment to a Eurob-

lock connector, strip the

wire as shown in the

illustration, and use

stranded wire to make

connections. With a Euroblock connection, the stranded

wire may be prone to breakage because of metal fatigue

due to the weight of the cable or due to vibration. When

rack-mounting your equipment, use a lacing bar when

possible to bundle and fasten the cables.

• If cables will be fre-

quently connected and

disconnected, as in the

case of a portable instal-

lation, we recommend

that you use ferrules with

insulation sleeves. Use a

ferrule whose conductor

portion has an external diameter of 1.6 mm or less, and a

length of approximately 7 mm (such as the AI0,5-6WH

made by the Phoenix Contact corporation).

CAUTION

• If you use stranded wire, do not tin (plate with solder) the

exposed end.

approx. 7 mm

1.6 mm or less

3mm

Euroblock plug

Ter minal screw

Slotted screwdriver

Loosen

Connections

14 IMX644 Owner’s Manual

3 Securely tighten the terminal screws.

Pull the cables (not too strongly) to conﬁrm that they are

securely connected.

4 Connect the Euroblock plug to the IMX644

Euroblock connector.

■ [REMOTE] Connector (RS-232C)

Connect to this connector when controlling the IMX644 from

the IMX644 Manager application or an external AMX/Crestron

controller. Use an RS-232C cross cable for connection.

An external AMX or similar controller can be used to send com-

mands to the IMX644 to recall memories and adjust the level of

individual channels. Refer to page 20 for information on the

available remote control commands.

■ [GPI] Connector (25-pin D-sub)

External GPI (General Purpose Interface) control devices can be

connected to this connector to allow input and output of remote

control signals.

The IMX644 GPI port has eight inputs and eight outputs, plus a

dedicated “POWER MONITOR” output that indicates the unit’s

ON/OFF status.

The input pins are normally left open. Shorting an input pin to

ground (GND) recalls the corresponding memory number.

The output pins are open-collector outputs that deliver a maxi-

mum output of +35 volts, with a maximum current capability of

30 mA per port.

For the POWER MONITOR outputs, pins 24 and 25 are

“closed” (shorted) when the power is ON. The POWER MONI-

TOR COLD pin (pin 25) is internally connected to the GND

pins.

The IMX644 Manager application can be used for parameter as-

signment.

1234

6789

Connector Pin

Assignments

Pin No. Signal name

1Unused

2 RxD

3 TxD

4 DTR

5 GND

6 DSR

7RTS

8 CTS

9Unused

Pin No. Signal name

1 GND

2 GND

3 INPUT 1

4 INPUT 2

5 INPUT 3

6 INPUT 4

7 INPUT 5

8 INPUT 6

9 INPUT 7

10 INPUT 8

11 GND

12 GND

13 GND

14 OUTPUT 1

15 OUTPUT 2

16 OUTPUT 3

17 OUTPUT 4

18 OUTPUT 5

19 OUTPUT 6

20 OUTPUT 7

21 OUTPUT 8

22 GND

23 GND

24 POWER MONITOR HOT

25 POWER MONITOR COLD

12345678910111213

25 24 23 22 21 20 19 18 17 16 15 14

Connector Pin Assignments

IMX644 Owner’s Manual 15

Mix Functions

The IMX644 mix functions can be programmed and edited in detail using the IMX644 Manager installed on a computer (page 7). The

mix functions that can be controlled by the IMX644 Manager application are discussed in this section. For operating details refer to the

IMX644 Manager Owner’s Manual.

To enable communication with the IMX644 Manager application, press and hold the IMX644 MEMORY [D] button while turning the

[POWER] switch ON.

■ GAIN

The gain of the mono input channel head amplifiers can be indi-

vidually adjusted and displayed.

■ INPUT EQ

The parameters of the input channel equalizers can be individu-

ally adjusted and displayed. The parameters available for each

channel are listed below.

MONO INPUT CHANNEL

STEREO INPUT CHANNEL

■ MATRIX

The MATRIX allows individual input channels to be assigned to

any of the mixer’s output channels. The assignments are shown

on the display. The initial default settings are: send assignments

to all output channels are ON, with only OUT1 assigned to the

REC OUT channel. The send levels from individual mono input

channels to the output channels can also be adjusted and dis-

played.

■ Temporary Matrix Assignment

Changes

The panel controls can be used to temporarily turn on the output

assignments of individual input channels, as follows.

1 Set all OUTPUT channel level controls to “0”.

2 Set the level of the INPUT channel to be

assigned to “10”.

3 Press and hold the MEMORY button correspond-

ing to the output channel you want to assign the

input channel to for longer than 3 seconds while

rotating the INPUT channel level control towards

“0”.

4 The corresponding MATRIX indicator will light.

5 Repeat for other channels as required.

NOTE

• Output assignments made in this way are only temporary and

will not be saved to memory. If power to the unit is turned

OFF and then ON again the memorized settings prior to

making the changes as described above will be recalled.

Input Channels

Parameter Range Initial value

GAIN (PAD is off) -54dB – -30dB -35dB

GAIN (PAD is ON) -20dB – +4dB -1dB

Parameter Range Initial value

HIGH

G -15dB – +15dB 0dB

F 2kHz – 18kHz 10kHz

MID

G -15dB – +15dB 0dB

F 40Hz – 18kHz 2kHz

Q 0.5 – 12.0 0.7

LOW

G -15dB – +15dB 0dB

F 40Hz – 2kHz 100Hz

Parameter Range Initial value

HIGH

G -15dB – +15dB 0dB

F 2kHz – 18kHz 10kHz

LOW

G -15dB – +15dB 0dB

F 40Hz – 2kHz 100Hz

Parameter Range Initial value

SEND LEVEL -∞ – 0dB 0dB

Button Output channel

A OUTPUT 1

B OUTPUT 2

C OUTPUT 3

D OUTPUT 4

Mix Functions

16 IMX644 Owner’s Manual

■ Feedback Suppressor

The Feedback Suppressor effectively controls feedback by iden-

tifying the feedback frequencies that will occur naturally as a re-

sult of the combined acoustic and electrical characteristics of the

sound system within the acoustic space in which it is used. The

Feedback Suppressor includes static filters that provide mea-

surement and filtering for specified channels, and dynamic fil-

ters that monitor the condition of specified MONO INPUT

channels and automatically suppress feedback as it occurs.

Static filter measurements can be made either via the IMX644

Manager application or the IMX644 unit itself. Measurement

from the IMX644 itself is described in “Front Panel Static Filter

Measurement” below.

With the initial default settings the static filters are inactive,

while the dynamic filters are ON for all MONO INPUT chan-

nels.

NOTE

• The initial default setting is Feedback Suppressor ON. Even

though the static ﬁlters are inactive, the dynamic ﬁlters are

still operational so be sure to turn the Feedback Suppressor

OFF before using sine waves or test tones to test or calibrate

the system.

•Feedback Suppressor settings can be stored in the unit’s 16

memories.

Front Panel Static Filter Measurement

To ensure optimum feedback suppression be sure to perform the

measurements under the same conditions that will prevail during

actual operation (microphone and speaker positions, etc.).

1 Set the OUTPUT channel 1 through 4 level con-

trols to 3 o’clock.

2 Set the level control of the MONO INPUT to

which the microphone that is to be used for

measurement is connected to 3 o’clock.

3 Set up the microphone at least 5 meters away

from the speakers.

4 Adjust the output level of the power ampliﬁer.

While speaking or singing into the microphone gradually

raise the output level of the power ampliﬁer to the level

that will be used in actual operation. Also clap your hands

near the microphone to make sure that feedback does not

occur.

5 Set the level control of the MONO INPUT channel

to which the microphone that is to be used for

measurement is connected to “0”.

6 Make sure the area being measured is silent.

7 Simultaneously press and hold MEMORY but-

tons [A], [C], and [D] for longer than two sec-

onds. The MEMORY [A], [C], and [D] button

indicators will light and static ﬁlter measure-

ment will begin. When the measurement process

has ﬁnished the static ﬁlter will be set according

to the results and the MEMORY button indica-

tors will return to their status prior to the mea-

surement.

NOTE

• If all four MEMORY button indicators light – [A], [B], [C], and

[D] – an error has occurred during measurement. To prevent

damage to the equipment the measurement will be aborted

and the erroneous data discarded. If this occurs try changing

the orientation of the microphone and speakers, lower the

ampliﬁer output, then repeat the procedure from step 1

above.

• Static ﬁlter measurement may not be successful if the overall

level is too high or the microphone is too close to one of the

speakers.

■ Priority Ducker

When a signal is applied to the specified MONO INPUT channel

the level of all STEREO INPUT signals assigned to the same

output are reduced to allow announcements made via the MONO

INPUT channel to stand out clearly from background music or

other program material, for example. When input to the specified

MONO INPUT channel ceases the level of the other “ducked”

channels returns to normal.

The initial default setting is OFF for all channels.

Both the amount of attenuation and the time it takes to return to

normal level can be programmed as required.

■ Music Override

When a signal is applied to the specified STEREO INPUT chan-

nel all other STEREO INPUT channels assigned to the same out-

put are automatically faded out and muted. When input to the

specified STEREO INPUT channel ceases the level of the other

muted channels fades in and returns to normal.

The initial default setting is OFF for all channels.

The time it takes to fade-in to normal level can be programmed

as required.

NOTE

• If Music Override is ON for more than one channel, the low-

est-numbered channel takes priority.

Parameter Range Initial value

Mute Level -30.2dB – 0dB -20dB

Release Time 0.0 – 6.0sec 2.0sec

Parameter Range Initial value

Release Time 0.0 – 6.0sec 4.0sec

Mix Functions

IMX644 Owner’s Manual 17

■ OUTPUT EQ

The parameters of the independent 6-band parametric equalizers

provided for OUTPUT channels 1 through 4 can be adjusted and

displayed. The following EQ types can be specified for each

band.

The initial default settings when the P.EQ type is selected are as

follows.

■ DELAY

Sets the output channel delay time.

One of the main uses for this feature is to delay the output to sub

speakers slightly compared to the main speakers, to create a solid

frontal sonic image.

■ BALANCE

Adjusts the A/B level balance for OUTPUT channels 1 and 2.

■ Output Format (STEREO/MONO)

Specifies whether OUTPUT channels 1 and 2 deliver a STEREO

or MONO output signal. When [STEREO] is selected the left

channel signal is delivered via the A connector and the right-

channel signal is delivered via the B connector. The initial de-

fault setting is [STEREO].

■ GPI (General Purpose Interface)

• GPI Input

Applying an appropriate input to one of the rear-panel GPI

input ports recalls the assigned memory. Individual assign-

ments can be made for each input port.

• GPI Output

Recalling a memory causes a pre-assigned combination of

ON and OFF outputs to appear at the GPI output ports. The

ON/OFF combinations can be independently assigned for

each memory.

The initial default assignments for all memories are all out-

puts OFF.

■ MEMORY

Up to 16 sets of parameters can be memorized. Of those, four

can be assigned for direct recall from the front-panel MEMORY

[A] through [D] buttons. For access to five or more memories at

a time either use the IMX644 Manager application, or a suitable

external controller connected to the GPI interface.

NOTE

• MEMORY buttons [A] through [D] are initially set up to recall

the same data.

• Since the level settings for each channel are stored in the

IMX644 unit itself, be sure that the IMX644 Manager

application is online when setting up the memories.

Output Channels

Type Parameter Range

PEQ (Peaking EQ)

F 40Hz – 18kHz

G -15dB – +15dB

Q 0.5 – 12.0

HPF (High Pass Filter)

F 40Hz – 18kHz

Slope 12dB/oct (Fixed)

Q 0.7 (Fixed)

LPF (Low Pass Filter)

F 40Hz – 18kHz

Slope 12dB/oct (Fixed)

Q 0.7 (Fixed)

L. Shelf (Low Shelving EQ)

F 40Hz – 18kHz

G -15dB – +15dB

H.Shelf (High Shelving EQ)

F 40Hz – 18kHz

G -15dB – +15dB

Parameter Initial value

Q 0.7 (for all frequency parameters)

F1 40Hz

F2 100Hz

F3 500Hz

F4 2kHz

F5 5kHz

F6 10kHz

Parameter Range Initial value

DELAY 0 – 300msec 0msec

Parameter Range Initial value

BALANCE 0dB – 20.1dB 0dB

Others

18 IMX644 Owner’s Manual

Appendix

The following procedure initializes the IMX644 memory.

CAUTION

• All data stored in memory will be erased when the memory is initialized. Perform the following procedure with caution.

1 Turn the IMX644 power OFF.

2 Turn the power back ON while simultaneously holding the MEM-

ORY [A] and [D] buttons.

Initialization will take about one second.

When initialization is complete the odd-numbered matrix input channel indica-

tors will light.

Troubleshooting

Symptom Possible Cause Solution

The power won’t turn on.

The power cable is not prop-

erly connected.

After connecting the power cable to the connector on the rear panel

of the IMX644, plug the cable into an appropriate AC outlet.

No sound.

The audio cables are not

properly connected.

Check all audio connections.

Connected devices are not

turned ON.

Check to make sure that the power to all connected devices is turned ON.

Wrong matrix settings.

Check the matrix indicators to make sure that the input and output

assignments are correct. If the matrix settings are not appropriate

use the IMX644 Manager application to set them as required. Also

check the matrix send levels.

Level settings too low.

Make sure that the panel level controls are set appropriately. If this

doesn’t produce the desired output check the settings via the IMX644

manager application.

Sound levels don’t change

when the level knobs are

operated.

The LOCK function may be

engaged.

Disengage the main LOCK function via the IMX644 panel (page 8),

or disengage LOCK for a speciﬁc knob via the IMX644 Manager

application.

Pressing a MEMORY button

results in no change to the

settings.

The MEMORY button is not

being held long enough.

Press and hold the MEMORY button for longer than two seconds.

No settings have been

saved in memory.

Make the required settings via the IMX644 Manager application, and

then save them to the appropriate memory.

The appropriate memory-to-

button assignment has not

been made.

Use the IMX644 Manager application to assign the desired memory

to the button.

The IMX644 cannot be locked.

The [LOCK] switch hasn’t

been properly pressed. The

LOCK indicator will be off if

the controls aren’t locked.

Press the [LOCK] switch (page 8). The LOCK indicator will light when

the controls are locked.

The [LOCK] switch doesn

’

work.

The IMX644 has been

locked via the IMX644 Man-

ager application.

Make sure that the [LOCK] buttons in the IMX644 Manager BLOCK

or INPUT screen are turned on (pages 21 and 24 of the IMX644

Manager owner’s manual).

Memory cannot be recalled

via the GPI interface.

A memory is not assigned to

the GPI input.

Use the IMX644 Manager application to assign the desired memory

to the GPI Input Terminal.

The IMX644 cannot be oper-

ated from an external con-

troller (AMX/Crestron).

The IMX644 is operating in

IMX644 Manager mode.

Turn the IMX644 power OFF, and then after waiting for at least six

seconds turn the power ON again (without

holding the MEMORY [D]

button) to start the IMX644 in “normal” mode.

The IMX644 cannot be oper-

ated from the IMX644 Man-

ager application.

The IMX644 is operating in

normal mode.

Turn the IMX644 power OFF, and then after waiting for at least six

seconds turn the power ON again while holding the MEMORY [D]

button to start the IMX644 in “IMX644 Manager” mode.

The Parameter Edit screen

will not open when the pass-

word is entered via the

IMX644 Manager.

The password is incorrect.

Initialize the internal IMX644 memory if the password has been lost

or forgotten.

Memory Initialization

Appendix

IMX644 Owner’s Manual 19

3 To recall the initial memory data press a MEMORY button for longer than two seconds.

NOTE

• Initialization erases the password required to connect the IMX644 Manager application to the IMX644 unit. After initialization it will be

necessary to set a new password to bring the IMX644 online.

The chart below shows the panel and memory recall operations that are effective with various combinations of modes, panel LOCK

settings, and IMX644 Manager LOCK/LINK settings, and whether the panel or memorized level settings are applied when a memory

is recalled.

* When the IMX644 is online in the IMX644 Manager mode, LOCK is temporarily disengaged and the panel [LOCK] indicator will go

out. Do not operate the panel [LOCK] switch in this condition.

NOTE

• Since the level settings for each channel are stored in the IMX644 unit itself, be sure that the IMX644 Manager application is online

when setting up the memories.

IMX644 Status List

IMX644 Settings

Individual

Channel Settings

(IMX644

Manager)

Operations that Affect Actual

Level

Operations that Recall Memories

[LOCK]

indicator

[LOCK]

button

[LINK]

button

Level

Knobs

IMX644

Manager

Control

External

Controller

MEMORY

buttons

GPI

IMX644

Manager

Control

External

Controller

Level

Setting

IMX644

Manager

Mode

Ofﬂine

unlit ON ON Effective – –

Effective Effective – –

Level Knob

Setting

unlit ON OFF Effective – –

Memory

Setting

unlit OFF ON Effective – –

Level Knob

Setting

unlit OFF OFF Effective – –

Memory

Setting

lit ON ON Invalid – –

Effective Effective – –

Memory

Setting

lit ON OFF Invalid – –

Memory

Setting

lit OFF ON Effective – –

Level Knob

Setting

lit OFF OFF Effective – –

Memory

Setting

Online*

unlit ON ON Effective Invalid –

Effective Effective Effective –

Level Knob

Setting

unlit ON OFF Invalid Effective –

Memory

Setting

unlit OFF ON Effective Invalid –

Level Knob

Setting

unlit OFF OFF Invalid Effective –

Memory

Setting

Normal Mode

unlit ON ON Effective – Effective

Effective Effective – Effective

Level Knob

Setting

unlit ON OFF Effective – Effective

Memory

Setting

unlit OFF ON Effective – Effective

Level Knob

Setting

unlit OFF OFF Effective – Effective

Memory

Setting

lit ON ON Invalid – Effective

Effective Effective – Effective

Memory

Setting

lit ON OFF Invalid – Effective

Memory

Setting

lit OFF ON Effective – Effective

Level Knob

Setting

lit OFF OFF Effective – Effective

Memory

Setting

Appendix

20 IMX644 Owner’s Manual

The commands that can be transferred between the IMX644 and a remote controller are as follows.

•A line feed (LF = 0x0A) is necessary at then end of every command line.

• At least one character space is required between the command name and ﬁrst option, and between options.

■ Communication Speciﬁcations

Baud Rate : 38400 bps

Data : 8bit

Parity : none

Stop Bit : 1bit

Flow Control : none

Memory Recall Individual Channel Level Control

m: memory number (1–16)

Remote Control Protocol Speciﬁcations

Communication Direction Command

External Controller IMX644

RSC 0 m

External Controller IMX644

RSC OK

External Controller IMX644

SCN 0 m

External Controller IMX644

VOL 0 0 x

VOL 0 1 x

VOL 0 13 x

➜

...

➜

...

Communication Direction Command

External Controller IMX644

SVL 0 c x

External Controller IMX644

SVL OK

External Controller IMX644

VOL 0 c x

➜

c: channel number (0–13)

0 MONO 1

1 MONO 2

2 MONO 3

3 MONO 4

4 MONO 5

5 MONO 6

6 STEREO 1

7 STEREO 2

8 STEREO 3

9 STEREO 4

10 OUTPUT1

11 OUTPUT2

12 OUTPUT3

13 OUTPUT4

x: level value (0–127)

127 -∞

126 -∞

125 -∞

124 -111.4

123 -102.4

122 -94.4

121 -88.4

120 -83.4

119 -78.4

118 -74.4

117 -70.4

116 -66.4

115 -63.8

114 -60.6

113 -57.6

112 -55.1

111 -52.9

110 -50.9

109 -49.1

108 -47.5

107 -46.0

106 -44.5

105 -43.1

104 -41.7

103 -40.4

102 -39.1

101 -37.9

100 -36.7

99 -35.6

98 -34.5

97 -33.6

96 -32.7

95 -31.8

94 -31.0

93 -30.2

92 -29.4

91 -28.7

90 -28.0

89 -27.3

88 -26.7

87 -26.1

86 -25.5

85 -24.9

84 -24.4

83 -23.9

82 -23.4

81 -22.9

80 -22.4

79 -22.0

78 -21.6

77 -21.2

76 -20.8

75 -20.4

74 -20.0

73 -19.6

72 -19.2

71 -18.8

70 -18.4

69 -18.0

68 -17.6

67 -17.2

66 -16.8

65 -16.4

64 -16.0

63 -15.6

62 -15.2

61 -14.8

60 -14.4

59 -14.0

58 -13.6

57 -13.2

56 -12.8

55 -12.4

54 -12.0

53 -11.6

52 -11.2

51 -10.8

50 -10.4

49 -10.0

48 -9.6

47 -9.2

46 -8.8

45 -8.4

44 -8.0

43 -7.6

42 -7.2

41 -6.8

40 -6.4

39 -6.0

38 -5.6

37 -5.2

36 -4.8

35 -4.4

34 -4.0

33 -3.6

32 -3.2

31 -2.8

30 -2.4

29 -2.0

28 -1.6

27 -1.2

26 -0.8

25 -0.4

24 0.0

23 0.4

22 0.8

21 1.2

20 1.6

19 2.0

18 2.4

17 2.8

16 3.2

15 3.7

14 4.2

13 4.7

12 5.2

11 5.8

10 6.5

9 7.3

8 8.1

7 9.0

6 10.0

5 10.0

4 10.0

3 10.0

2 10.0

1 10.0

0 10.0

La pagina sta caricando ...

Yamaha IMX644 Manuale utente

Marca: Yamaha

Modello: IMX644

Categoria: Controller DJ

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: Yamaha IMX644 User manual
français: Yamaha IMX644 Manuel utilisateur
español: Yamaha IMX644 Manual de usuario
Deutsch: Yamaha IMX644 Benutzerhandbuch
русский: Yamaha IMX644 Руководство пользователя
Nederlands: Yamaha IMX644 Handleiding
português: Yamaha IMX644 Manual do usuário
dansk: Yamaha IMX644 Brugermanual
čeština: Yamaha IMX644 Uživatelský manuál
polski: Yamaha IMX644 Instrukcja obsługi
svenska: Yamaha IMX644 Användarmanual
Türkçe: Yamaha IMX644 Kullanım kılavuzu
suomi: Yamaha IMX644 Ohjekirja
română: Yamaha IMX644 Manual de utilizare

Documenti correlati

Altri documenti

Shure DFR22 Guida utente