Indesit IWE 71282 ECO (EU) Guida utente

Categoria
Lavatrici
Tipo
Guida utente
GB
1
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 4
Cutting off the water or electricity supply
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and tips, 5
General safety
Disposal
Opening the porthole door manually
Description of the washing machine,6-7
Control panel
Display
Running a wash cycle, 8
Wash cycles and options, 9
Table of wash cycles
Wash options
Detergents and laundry, 10
Detergent dispenser drawer
Preparing the laundry
Special wash cycles
Load balancing system
Troubleshooting, 11
Service, 12
IWE 71282
Instructions for use
WASHING MACHINE
English,1
GB
Espańol,13
ES
Portuguęs,25
PT
GR
ΕΛΛΗΝΙΚΑ,37
Български,49
BG
2
GB
Installation
! This instruction manual should be kept in a safe
place for future reference. If the washing machi-
ne is sold, transferred or moved, make sure that
the instruction manual remains with the machine
so that the new owner is able to familiarise him-
self/herself with its operation and features.
! Read these instructions carefully: they con-
tain vital information relating to the safe instal-
lation and operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its
packaging.
2. Make sure that the washing machine has
not been damaged during the transportation
process. If it has been damaged, contact the
retailer and do not proceed any further with
the installation process.
3. Remove the 4 pro-
tective screws (used
during transportation)
and the rubber wa-
sher with the cor-
responding spacer,
located on the rear
part of the appliance
(see figure).
4. Close off the holes using the plastic plugs
provided.
5. Keep all the parts in a safe place: you will
need them again if the washing machine ne-
eds to be moved to another location.
! Packaging materials should not be used as
toys for children.
Levelling
1. Install the washing machine on a flat sturdy
floor, without resting it up against walls, furni-
ture cabinets or anything else.
2. If the floor is not
perfectly level, com-
pensate for any une-
venness by tightening
or loosening the
adjustable front feet
(see figure); the angle
of inclination, measu-
red in relation to the
worktop, must not
exceed 2°.
Levelling the machine correctly will provide
it with stability, help to avoid vibrations and
excessive noise and prevent it from shifting
while it is operating. If it is placed on carpet or
a rug, adjust the feet in such a way as to allow
a sufficient ventilation space underneath the
washing machine.
Connecting the electricity and
water supplies
Connecting the water inlet hose
1. Connect the sup-
ply pipe by screwing
it to a cold water tab
using a ¾ gas threa-
ded connection (see
figure).
Before performing the
connection, allow the
water to run freely un-
til it is perfectly clear.
2. Connect the inlet
hose to the washing
machine by screwing
it onto the correspon-
ding water inlet of the
appliance, which is
situated on the top
right-hand side of the
rear part of the ap-
pliance (see figure).
3. Make sure that the hose is not folded over
or bent.
! The water pressure at the tap must fall within
the values indicated in the Technical details
table (see next page).
! If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
GB
3
Technical data
Model
IWE 71282
Dimensions
width 59.5 cm
height 85 cm
depth 53,5 cm
Capacity
from 1 to 7 kg
Electrical
connections
please refer to the technical
data plate fixed to the machine
Water
connection
maximum pressure
1 MPa (10 bar)
minimum pressure
0.05 MPa (0.5 bar)
drum capacity 52 litres
Spin speed
up to 1200 rotations per
minute
Test wash
cycles in
accordan-
ce with
directives
1061/2010
and
1015/2010
Programme 3:
Cotton standard 60°C.
Programme 4:
Cotton standard 40°C.
This appliance conforms to
the following EC Directives:
- 2004/108/EC dated
03/05/89 (Electromagnetic
Compatibility)
- 2012/19/EU
- 2006/95/EC Low Voltage)
65 - 100 cm
Connecting the drain hose
Connect the drain
hose, without bending
it, to a drainage duct
or a wall drain located
at a height between
65 and 100 cm from
the floor;
alternatively, rest it on
the side of a washba-
sin or bathtub, faste-
ning the duct sup-
plied to the tap (see
figure). The free end
of the hose should
not be underwater.
! We advise against the use of hose exten-
sions; if it is absolutely necessary, the exten-
sion must have the same diameter as the
original hose and must not exceed 150 cm in
length.
Electrical connections
Before plugging the appliance into the electri-
city socket, make sure that:
the socket is earthed and complies with all
applicable laws;
the socket is able to withstand the maximum
power load of the appliance as indicated in
the Technical data table (see opposite);
the power supply voltage falls within the
values indicated in the Technical data table
(see opposite);
the socket is compatible with the plug of
the washing machine. If this is not the case,
replace the socket or the plug.
! The washing machine must not be installed
outdoors, even in covered areas. It is extreme-
ly dangerous to leave the appliance exposed
to rain, storms and other weather conditions.
! When the washing machine has been instal-
led, the electricity socket must be within easy
reach.
! Do not use extension cords or multiple sockets.
! The cable should not be bent or compressed.
! The power supply cable must only be repla-
ced by authorised technicians.
Warning! The company shall not be held
responsible in the event that these regulations
are not respected.
The first wash cycle
Once the appliance has been installed, and
before you use it for the first time, run a wash
cycle with detergent and no laundry, using the
wash cycle 2.
4
GB
Care and maintenance
Cutting off the water and electri-
city supplies
Turn off the water tap after every wash cycle.
This will limit wear on the hydraulic system
inside the washing machine and help to pre-
vent leaks.
Unplug the washing machine when cleaning
it and during all maintenance work.
Cleaning the washing machine
The outer parts and rubber components of the
appliance can be cleaned using a soft cloth
soaked in lukewarm soapy water. Do not use
solvents or abrasives.
Cleaning the detergent dispenser
drawer
Remove the dispenser
by raising it and pul-
ling it out (see figure).
Wash it under running
water; this operation
should be repeated
frequently.
Caring for the door and drum of
your appliance
Always leave the porthole door ajar in order
to prevent unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-cle-
aning pump which does not require any main-
tenance. Sometimes, small items (such as
coins or buttons) may fall into the pre-chamber
which protects the pump, situated in its bot-
tom part.
! Make sure the wash cycle has finished and
unplug the appliance.
To access the pre-chamber:
1. using a screwdri-
ver, remove the cover
panel on the lower
front part of the wa-
shing machine (see
figure);
2. unscrew the lid
by rotating it anti-
clockwise (see figu-
re): a little water may
trickle out. This is
perfectly normal;
3. clean the inside thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks
are securely in place before you push it onto
the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If
there are any cracks, it should be replaced
immediately: during the wash cycles, water
pressure is very strong and a cracked hose
could easily split open.
! Never use second-hand hoses.
GB
5
Precautions and tips
! This washing machine was designed and constructed in
accordance with international safety regulations. The fol-
lowing information is provided for safety reasons and must
therefore be read carefully.
General safety
This appliance was designed for domestic use only.
This appliance can be used by children aged
from 8 years and above and persons with re-
duced physical, sensory or mental capabilities
or lack of experience and knowledge if they
have been given supervision or instruction
concerning use of the appliance in a safe way
and understand the hazards involved. Chil-
dren shall not play with the appliance. Clea-
ning and user maintenance shall not be made
by children without supervision.
Do not touch the machine when barefoot or with wet or
damp hands or feet.
Do not pull on the power supply cable when unplugging
the appliance from the electricity socket. Hold the plug
and pull.
Do not open the detergent dispenser drawer while the
machine is in operation.
Do not touch the drained water as it may reach extreme-
ly high temperatures.
Never force the porthole door. This could damage the
safety lock mechanism designed to prevent accidental
opening.
If the appliance breaks down, do not under any circum-
stances access the internal mechanisms in an attempt
to repair it yourself.
Always keep children well away from the appliance while
it is operating.
The door can become quite hot during the wash cycle.
If the appliance has to be moved, work in a group of two
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.
Before loading laundry into the washing machine, make
sure the drum is empty.
Disposal
Disposing of the packaging materials: observe local
regulations so that the packaging may be re-used.
The European Directive 2012/19/EU on Waste
Electrical and Electronic Equipment, requires that
old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected separately
in order to optimise the recovery and recycling of the
materials they contain and reduce the impact on human
health and the environment. The crossed out “wheeled
bin” symbol on the product reminds you of your obliga-
tion, that when you dispose of the appliance it must be
separately collected.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
Opening the porthole door manually
In the event that it is not possible to open the porthole
door due to a powercut, and if you wish to remove the
laundry, proceed as follows:
1. remove the plug from the
electrical socket.
2. make sure the water level
inside the machine is lower
than the door opening; if it
is not, remove excess water
using the drain hose, collec-
ting it in a bucket as indicated
in the figure.
3. using a screwdriver, remo-
ve the cover panel on the lo-
wer front part of the washing
machine (see figure).
4. pull outwards using the tab as indicated in the figure,
until the plastic tie-rod is freed from its stop position; pull
downwards and open the door at the same time.
5. reposition the panel, making sure the hooks are securely
in place before you push it onto the appliance.
6
GB
Detergent dispenser drawer: used to dispense
detergents and washing additives (see “Detergents and
laundry”).
ON/OFF button : press this briefly to switch the ma-
chine on or off. The START/PAUSE indicator light, which
flashes slowly in a green colour shows that the machine is
switched on. To switch off the washing machine during the
wash cycle, press and hold the button for approximately 2
seconds; if the button is pressed briefly or accidentally the
machine will not switch off. If the machine is switched off
during a wash cycle, this wash cycle will be cancelled.
WASH CYCLE knob: used to set the desired wash cycle
(see “Table of wash cycles”).
OPTION buttons with indicator light: used to select the
available options. The indicator light corresponding to the
selected option will remain lit.
SPIN button : press to reduce or completely exclude
the spin cycle - the value is indicated on the display.
TEMPERATURE button : press to decrease or comple-
tely exclude the temperature: the value will be shown on
the display.
DELAYED START button : press to set a delayed start
time for the selected wash cycle. The delay time will be
shown on the display.
START/PAUSE button with indicator light: when the
green indicator light flashes slowly, press the button to
start a wash cycle. Once the cycle has begun the indicator
light will remain lit in a fixed manner. To pause the wash
cycle, press the button again; the indicator light will flash
in an orange colour. If the symbol is not illuminated, the
door may be opened. To start the wash cycle from the
point at which it was interrupted, press the button again.
Standby mode
This washing machine, in compliance with new energy sa-
ving regulations, is fitted with an automatic standby system
which is enabled after about 30 minutes if no activity is
detected. Press the ON-OFF button briefly and wait for the
machine to start up again.
Description of the washing
machine
Control panel
TEMPERATURE
Button
Detergent dispenser drawer
OPTION
buttons with
indicator lights
ON/OFF
button
SPIN SPEED
Button
START/PAUSE
button with indicator light
DISPLAY
DELAYED
START Button
WASH CYCLE
knob
GB
7
Display
The display is useful when programming the machine and provides a great deal of information.
The duration of the available programmes and the remaining time of a running cycle appear in section A; if the DELAY START
option has been set, the countdown to the start of the selected programme will appear. Pressing the relative button, the
machine automatically displays the maximum temperature and spin speed values set for the selected cycle, or the most
recently-used settings if they are compatible with the selected cycle.
The “programme phases” relative to the selected programme and the “programme phase” of the running programme appear
in section B:
Wash
Rinse
Spin
Drain
The icons corresponding to “temperature” , “Programmed start” and “spin” appear in section C from top to bottom:
If the symbol lights up, the display will visualise the set “temperature” value.
When a “delayed start” has been set, the symbol lights up.
If the symbol lights up, the display will visualise the set “spin” value.
Door locked symbol
The lit symbol indicates that the door is locked. To prevent any damage, wait until the symbol turns off before opening the
door.To open the door while a cycle is in progress, press the START/PAUSE button; if the DOOR LOCKED symbol is
switched off the door may be opened.
B
CA
8
GB
Running a wash cycle
1. SWITCH THE MACHINE ON. Press the button;
the START/PAUSE indicator light will flash slowly in a
green colour.
2. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed
the maximum load value indicated in the table of
programmes on the following page.
3. MEASURE OUT THE DETERGENT. Pull out the
detergent dispenser drawer and pour the detergent into
the relevant compartments as described in “Detergents
and laundry”.
4. CLOSE THE DOOR.
5. SELECT THE WASH CYCLE. Set the WASH CYCLE
knob to the desired programme; a temperature and
spin speed is set for each wash cycle; these may be
adjusted. The duration of the cycle will appear on the
display.
6. CUSTOMISE THE WASH CYCLE. Use the relevant
buttons:
Modifying the temperature and/or spin
speed. The machine automatically displays the
maximum temperature and spin speed values set for
the selected cycle, or the most recently-used settings
if they are compatible with the selected cycle. The
temperature can be decreased by pressing the
button, until the cold wash “OFF” setting is reached.
The spin speed may be progressively reduced by
pressing the button, until it is completely excluded
(the “OFF” setting). If these buttons are pressed again,
the maximum values are restored.
Setting a delayed start.
To set a delayed start for the selected programme,
press the corresponding button repeatedly until the
required delay period has been reached. When this
option is enabled, the symbol lights up on the
display. To remove the delayed start option press the
button until the text “OFF” appears on the display.
Modifying the cycle settings.
Press the button to enable the option; the indicator
light corresponding to the button will switch on.
Press the button again to disable the option; the
indicator light will switch off.
! If the selected option is not compatible with the
programmed wash cycle, the indicator light will flash
and the option will not be activated.
! If the selected option is not compatible with another
option which has been selected previously, the indicator
light corresponding to the first option selected will
flash and only the second option will be activated; the
indicator light corresponding to the enabled option will
remain lit.
! The options may affect the recommended load value
and/or the duration of the cycle.
7. START THE PROGRAMME. Press the START/
PAUSE button. The corresponding indicator light will
become green, remaining lit in a fixed manner, and the
door will be locked (the DOOR LOCKED symbol will
be on). To change a wash cycle while it is in progress,
pause the washing machine using the START/PAUSE
button (the START/PAUSE indicator light will flash slowly
in an orange colour); then select the desired cycle and
press the START/PAUSE button again.
To open the door while a cycle is in progress, press the
START/PAUSE button; if the DOOR LOCKED symbol
is switched off the door may be opened. Press the
START/PAUSE button again to restart the wash cycle
from the point at which it was interrupted.
8. THE END OF THE WASH CYCLE. This will be
indicated by the text “END” on the display; when the
DOOR LOCKED symbol switches off the door may be
opened. Open the door, unload the laundry and switch
off the machine.
! If you wish to cancel a cycle which has already begun,
press and hold the button. The cycle will be stopped
and the machine will switch off.
GB
9
Wash cycles and options
Wash options
Selecting this option enables you to suitably adjust drum
rotation, temperature and water to a reduced load of lightly
soiled cotton and synthetic fabrics (refer to the “Table of
wash cycles”). “ ” enables you to wash in less time
thereby saving water and electricity. We suggest using a
liquid detergent suitably measured out to the load quantity.
! This function may not be used in conjunction with wash
cycles 1, 2, 7, 8, 9, 10, 11, 12, 13, 14, , .
The function saves energy by not heating the
water used to wash your laundry - an advantage both to
the environment and to your energy bill. Instead, intensified
wash action and water optimisation ensure great wash
results in the same average time of a standard cycle.
For the best washing results we recommend the usage of
a liquid detergent.
! This function may not be used in conjunction with wash
cycles 1, 7, 8, 9, 12, 13, 14, , .
Table of wash cycles
Extra rinse
By selecting this option, the efficiency of the rinse is
increased and optimal detergent removal is guaranteed. It
is particularly useful for sensitive skin.
! This function may not be used in conjunction with wash
cycle .
Easy iron
By selecting this function, the wash and spin cycles will be
modified in order to reduce the formation of creases. At
the end of the cycle the washing machine will perform slow
rotations of the drum; the indicator lights for the EASY IRON
and START/PAUSE options will flash (the first one green, the
second orange). To end the cycle, press the START/PAUSE
button or the EASY IRON button. For the 9,11 wash cycles,
the machine will end the cycle while the laundry is soaking
and the EASY IRON and START/PAUSE indicator lights will
flash. To drain the water so that the laundry may be remo-
ved, press the START/PAUSE button or the EASY IRON
button.
! This function may not be used in conjunction with wash
cycles 8, 12, 13, 14, , .
1) Test wash cycle in compliance with directive 1061/2010: set wash cycle 3 with a temperature of 60°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for
garments which can be washed at 60°C. The actual washing temperature may differ from the indicated value.
2) Test wash cycle in compliance with directive 1061/2010: set wash cycle 4 with a temperature of 40°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for
garments which can be washed at 40°C. The actual washing temperature may differ from the indicated value.
For all Test Institutes:
2) Long wash cycle for cottons: set wash cycle 4 with a temperature of 40°C.
3) Long wash cycle for synthetics: set wash cycle 6; with a temperature of 40°C.
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors such as water
temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
Wash cycles
Description of the wash cycle
Max.
temp.
C)
Max.
speed
(rpm)
Detergents
Max. load (kg)
Residual
dampness %
Energy
consumption
kWh
Total water lt
Cycle
duration
Prewash
Wash
Fabric
softener
Daily
1
Cotton with prewash: extremely soiled whites. 90° 1200
7 53 2,21 78 170
2
Cotton: extremely soiled whites. 90° 1200 -
7 53 2,16 72 160
3
Cotton Standard 60° (1): heavily soiled whites and resistant colours. 60° 1200 -
7 53 1,10 52,5 190’
4
Cotton Standard 40° (2): lightly soiled whites and delicate colours. 40° 1200 -
7 53 1,09 92 185
5
Coloured Cottons: lightly soiled whites and delicate colours. 40° 1200 -
7 53 0,66 54 90
6
Synthetics: heavily soiled resistant colours. 60° 800 -
3,5 44 0,93 47 115
6
Synthetics (3): lightly soiled resistant colours. 40° 800 -
3,5 44 0,57 46 100
7
Cotton Standard 20°: lightly soiled whites and delicate colours. 20° 1200 -
7 - - - 170’
Special
8
Wool: for wool, cashmere, etc. 40° 800 -
1,5 - - - 70
9
Silk/Curtains: for garments in silk and viscose, lingerie. 30° 0 -
1 - - - 55’
10 Jeans
40° 800 -
3,5 - - - 75
11 Outwear
30° 400 -
- 2 - - - 60’
Sport
12 Sport Intensive
30° 600 -
2,5 - - - 85
13 Sport Light
30° 600 -
2,5 - - - 60
14 Special Shoes
30° 600 -
Max.
2 pairs
- - - 60’
Partial wash cycles
Rinse - 1200 - -
7 - - - 36‘
Spin + Drain - 1200 - - - 7 - - - 16‘
10
GB
Detergents and laundry
Detergent dispenser drawer
Good washing results also depend on the correct dose of
detergent: adding too much detergent will not necessa-
rily result in a more efficient wash, and may in fact cause
build up on the inside of your appliance and contribute to
environmental pollution.
! Do not use hand washing detergents because these
create too much foam.
! Use powder detergent for white cotton garments, for pre-
washing, and for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
Open the detergent di-
spenser drawer and pour
in the detergent or washing
additive, as follows.
compartment 1: Pre-wash detergent (powder)
compartment 2: Detergent for the wash cycle
(powder or liquid)
Liquid detergent should only be poured in immediately
prior to the start of the wash cycle.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
Preparing the laundry
• Divide the laundry according to:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
• Empty all garment pockets and check the buttons.
• Do not exceed the values listed in the “Table of wash cycles”,
which refer to the weight of the laundry when dry.
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g
Special wash cycles
Cotton Standard 20° (wash cycle 7) ideal for lightly soiled
cotton loads. The effective performance levels achieved at
cold temperatures, which are comparable to washing at 40°,
are guaranteed by a mechanical action which operates at
varying speed, with repeated and frequent peaks.
Wool: all wool garments can be washed using programme
8, even those carrying the “hand-wash only” label. For
best results, use special detergents and do not exceed
1,5 kg of laundry.
Silk: use special wash cycle 9 to wash all silk garments.
We recommend the use of special detergent which has
been designed to wash delicate clothes.
Curtains: fold curtains and place them in a pillow case or
mesh bag. Use wash cycle 9.
Jeans: Turn garments inside-out before washing and use
a liquid detergent. Use programme 10.
Outwear (wash cycle 11): is studied for washing water-re-
pellent fabrics and winter jackets (e.g. Gore-Tex, polyester,
nylon); for best results, use a liquid detergent and dosage
suitable for a half-load; pre-treat necks, cuffs and stains if
necessary; do not use softeners or detergents containing
softeners. Stuffed duvets cannot be washed with this
programme.
Sport Intensive (
wash cycle
12): is for washing heavily
soiled sports clothing fabrics (tracksuits, shorts, etc.);
for best results, we recommend not exceeding the ma-
ximum load indicated in the “Table of wash cycles”.
Sport Light (
wash cycle
13): is for washing lightly soiled
sports clothing fabrics (tracksuits, shorts, etc.); for best
results, we recommend not exceeding the maximum
load indicated in the “Table of wash cycles”. We recom-
mend using a liquid detergent and dosage suitable for a
half-load.
Special Shoes (
wash cycle
14): is for washing sports
shoes; for best results, do not wash more than 2 pairs
simultaneously.
Load balancing system
Before every spin cycle, to avoid excessive vibrations and
to distribute the load in a uniform manner, the drum rotates
continuously at a speed which is slightly greater than the
washing rotation speed. If, after several attempts, the load
is not balanced correctly, the machine spins at a reduced
spin speed. If the load is excessively unbalanced, the
washing machine performs the distribution process instead
of spinning. To encourage improved load distribution and
balance, we recommend small and large garments are
mixed in the load.
1
2
3
GB
11
Troubleshooting
Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure
that the problem cannot be solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not
take in water (“H2O” will flash on
the display).
The washing machine continuously
takes in and
drains water.
The washing machine does not
drain or spin.
The washing machine vibrates a lot
during the spin cycle.
The washing machine leaks.
The option indicator lights and the
start/pause indicator light flash and
an error code appears on the display
(e.g.: F-01, F-..).
There is too much foam.
Possible causes / Solutions:
The appliance is not plugged into the socket fully, or is not making contact.
There is no power in the house.
The washing machine door is not closed properly.
The ON/OFF button has not been pressed.
The START/PAUSE button has not been pressed.
The water tap has not been opened.
A delayed start has been set (see “Running a wash cycle”).
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap has not been opened.
There is no water supply in the house.
The pressure is too low.
The START/PAUSE button has not been pressed.
The drain hose is not fitted at a height between 65 and 100 cm from the floor
(see “Installation”).
The free end of the hose is under water (see “Installation”).
The wall drainage system is not fitted with a breather pipe.
If the problem persists even after these checks, turn off the water tap, switch
the appliance off and contact the Assistance Service. If the dwelling is on one of
the upper floors of a building, there may be problems relating to water drainage,
causing the washing machine to fill with water and drain continuously. Special
anti-draining valves are available in shops and help to avoid this inconvenience.
The wash cycle does not include draining: some wash cycles require the drain
phase to be started manually.
The “Easy iron” option has been activated: To complete the wash cycle, press
the START/PAUSE button (see “Wash cycles and options”).
The drain hose is bent (see “Installation”).
The drainage duct is clogged.
The drum was not unlocked correctly during installation (see “Installation”).
The washing machine is not level (see “Installation”).
The washing machine is trapped between cabinets and walls (see “Installation”).
The water inlet hose is not screwed on properly (see “Installation”).
The detergent dispenser drawer is blocked (for cleaning instructions, see “Care
and maintenance”).
The drain hose is not fixed properly (see “Installation”).
Switch off the machine and unplug it, wait for approximately 1 minute and then
switch it back on again.
If the problem persists, contact the Technical Assistance Service.
The detergent is not suitable for machine washing (it should display the text
“for washing machines” or “hand and machine wash”, or the like).
Too much detergent was used.
12
GB
Service
Before calling for Assistance:
Check whether you can solve the problem alone (see “Troubleshooting”);
Restart the programme to check whether the problem has been solved;
If this is not the case, contact an authorised Technical Assistance Centre using the telephone number provided on the
guarantee certificate.
! Always request the assistance of authorised technicians.
Have the following information to hand:
the type of problem;
the appliance model (Mod.);
the serial number (S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the
front of the appliance by opening the door.
ES
13
Español
Sumario
Instalación, 14-15
Desembalaje y nivelación
Conexiones hidráulicas y eléctricas
Primer ciclo de lavado
Datos técnicos
Mantenimiento y cuidados, 16
Interrumpir el agua y la corriente eléctrica
Limpiar la lavadora
Limpiar el contenedor de detergentes
Cuidar la puerta y el cesto
Limpiar la bomba
Controlar el tubo de alimentación de agua
Precauciones y consejos, 17
Seguridad general
Eliminaciones
Apertura manual de la puerta
Descripción de la lavadora, 18-19
Panel de control
Pantalla
mo efectuar un ciclo de lavado, 20
Programas y funciones, 21
Tabla de programas
Funciones de lavado
Detergentes y ropa, 22
Contenedor de detergentes
Preparar la ropa
Programas particulares
Sistema de equilibrado de la carga
Anomalías y soluciones, 23
Asistencia, 24
ES
IWE 71282
Manual de instrucciones
LAVADORA
14
ES
! Es importante conservar este manual para
poder consultarlo en cualquier momento. En
caso de venta, de cesión o de traslado, veri-
fique que permanezca junto con la lavadora
para informar al nuevo propietario sobre el
funcionamiento y brindar las correspondientes
advertencias.
! Lea atentamente las instrucciones: ellas
contienen importante información sobre la
instalación, el uso y la seguridad.
Desembalaje y nivelación
Desembalaje
1. Desembale la lavadora.
2. Controle que la lavadora no haya sufri-
do daños durante el transporte. Si estuviera
dañada no la conecte y llame al revendedor.
3. Quite los 4 tornillos
de protección para el
transporte y la aran-
dela de goma con
el correspondiente
distanciador ubicados
en la parte posterior
(ver la figura).
4. Cubra los orificios con los tapones de plá-
stico suministrados con el aparato.
5. Conserve todas las piezas: cuando la la-
vadora deba ser transportada nuevamente,
deberán volver a colocarse.
! Los embalajes no son juguetes para los
niños.
Nivelación
1. Instale la lavadora sobre un piso plano y
rígido, sin apoyarla en las paredes, muebles ni
en ningún otro aparato.
2. Si el piso no está
perfectamente hori-
zontal, compense las
irregularidades desen-
roscando o enroscan-
do las patas delante-
ras (ver la figura); el
ángulo de inclinación
medido sobre la su-
perficie de trabajo, no
debe superar los 2º.
Una cuidadosa nivelación brinda estabilidad
a la máquina y evita vibraciones, ruidos y
desplazamientos durante el funcionamiento.
Cuando se instala sobre moquetas o alfom-
bras, regule los pies para conservar debajo de
la lavadora un espacio suficiente para la venti-
lación.
Conexiones hidráulicas y eléctri-
cas
Conexión del tubo de alimentación de
agua
1. Conectar el tubo
de tubo enroscándolo
a un grifo de agua fría
con la boca roscada
de 3/4 gas (ver la
figura).
Antes de conectarlo,
haga correr el agua
hasta que esté límpi-
da.
2. Conecte el tubo de
alimentación a la lava-
dora enroscándolo en
la toma de agua cor-
respondiente ubicada
en la parte posterior
derecha (arriba) (ver la
figura).
3. Controle que en el tubo no hayan pliegues
ni estrangulaciones.
! La presión de agua del grifo debe estar com-
prendida dentro de los valores contenidos en
la tabla de Datos técnicos (ver la página corre-
spondiente).
! Si la longitud del tubo de alimentación no es
la suficiente, diríjase a un negocio especializa-
do o a un técnico autorizado.
! No utilice nunca tubos ya usados.
! Utilice los suministrados con la máquina.
Instalación
ES
15
Conexión del tubo de descarga
Conecte el tubo de
descarga, sin ple-
garlo, a una tubería
de descarga o a una
descarga de pared
colocadas a una altu-
ra del piso entre 65 y
100 cm;
o apóyelo en el borde
de un lavamanos
o de una bañe-
ra, uniendo la guía
suministrada con el
aparato, al grifo (ver
la figura). El extre-
mo libre del tubo de
descarga no debe
permanecer sumergi-
do en el agua.
! No se aconseja utilizar tubos de prolonga-
ción, si fuera indispensable hacerlo, la prolon-
gación debe tener el mismo diámetro del tubo
original y no superar los 150 cm.
Conexión eléctrica
Antes de enchufar el aparato, verifique que:
la toma tenga la conexión a tierra y haya
sido hecha según las normas legales;
la toma sea capaz de soportar la carga má-
xima de potencia de la máquina indicada en
la tabla de Datos técnicos (ver al costado);
la tensión de alimentación esté comprendida
dentro de los valores indicados en la tabla
de Datos técnicos (ver al costado);
la toma sea compatible con el enchufe de la
lavadora. Si no es así, sustituya la toma o el
enchufe.
! La lavadora no debe ser instalada al aire
libre, ni siquiera si el lugar está reparado, ya
que es muy peligroso dejarla expuesta a la
lluvia o a las tormentas.
! Una vez instalada la lavadora, la toma de
corriente debe ser fácilmente accesible.
! No utilice prolongaciones ni conexiones múl-
tiples.
65 - 100 cm
Datos técnicos
Modelo
IWE 71282
Dimensio-
nes
ancho 59,5 cm
altura 85 cm
profundidad 53,5 cm
Capacidad
de 1 a 7 kg
Conexiones
eléctricas
ver la placa de característi-
cas técnicas aplicada en la
máquina
Conexiones
hídricas
presión máxima
1 MPa (10 bar)
presión mínima
0,05 MPa (0,5 bar)
capacidad del cesto 52 litros
Velocidad de
centrifugado
máxima 1200 r.p.m.
Programas
de control
según las
directivas
1061/2010 y
1015/2010
Programa 3: programa normal
de algon a 60 °C;
Programa 4: programa normal
de algon a 40 °C.
Esta máquina cumple con lo
establecido por las siguientes
Directivas de la Comunidad:
- 2004/108/CE (Compatibili-
dad Electromagnética)
- 2012/19/EU
- 2006/95/CE (Baja Tensión)
! El cable no debe estar plegado ni sufrir com-
presiones.
! El cable de alimentación debe ser sustituido
sólo por técnicos autorizados.
¡Atención! La empresa fabricante declina toda
responsabilidad en caso de que estas normas
no sean respetadas.
Primer ciclo de lavado
Después de la instalación y antes del uso,
realice un ciclo de lavado con detergente y sin
ropa, seleccionando el programa 2.
16
ES
Interrumpir el agua y la corriente
eléctrica
Cierre el grifo de agua después de cada
lavado. De este modo se limita el desgaste
de la instalación hidráulica de la lavadora y
se elimina el peligro de pérdidas.
Desenchufe la máquina cuando la debe lim-
piar y durante los trabajos de mantenimiento.
Limpiar la lavadora
La parte externa y las partes de goma se pue-
den limpiar con un paño embebido en agua
tibia y jabón. No use solventes ni productos
abrasivos.
Limpiar el contenedor de deter-
gentes
Extraiga el contene-
dor levantándolo y
tirándolo hacia fuera
(ver la figura).
Lávelo debajo del
agua corriente, esta
limpieza se debe reali-
zar frecuentemente.
Cuidar la puerta y el cesto
Deje siempre semicerrada la puerta para
evitar que se formen malos olores.
Limpiar la bomba
La lavadora posee una bomba autolimpiante
que no necesita mantenimiento. Pero puede
suceder que objetos pequeños (monedas, bo-
tones) caigan en la precámara que protege la
bomba, situada en la parte inferior de la misma.
! Verifique que el ciclo de lavado haya termina-
do y desenchufe la máquina.
Para acceder a la
precámara:
1. quite el panel que
cubre la parte delan-
tera de la lavadora
con la ayuda de un
destornillador (ver la
figura);
Mantenimiento y cuidados
2. desenrosque la
tapa girándola en
sentido antihorario
(ver la figura): es nor-
mal que se vuelque
un poco de agua;
3. limpie con cuidado el interior;
4. vuelva a enroscar la tapa;
5. vuelva a montar el panel verificando, antes
de empujarlo hacia la máquina, que los gan-
chos se hayan introducido en las correspon-
dientes ranuras.
Controlar el tubo de alimentación
de agua
Controle el tubo de alimentación al menos
una vez al año. Si presenta grietas o rajaduras
debe ser sustituido: durante los lavados, las
fuertes presiones podrían provocar roturas
imprevistas.
! No utilice nunca tubos ya usados.
ES
17
Precauciones y consejos
! La lavadora fue proyectada y fabricada en conformidad
con las normas internacionales de seguridad. Estas adver-
tencias se suministran por razones de seguridad y deben
ser leídas atentamente.
Seguridad general
Este aparato ha sido fabricado para un uso de tipo
doméstico exclusivamente.
Este aparato puede ser utilizado por niños
de 8 años o más y por personas con capa-
cidades físicas, sensoriales o mentales di-
sminuidas o con experiencia y conocimien-
tos insuficientes siempre que sean supervi-
sados o que hayan recibido una adecuada
formación sobre el uso del aparato en forma
segura y conozcan los peligros derivados
del mismo. Los niños no deben jugar con el
aparato. El mantenimiento y la limpieza no
deben ser realizados por niños sin supervi-
sión.
La lavadora debe ser utilizada sólo por personas adul-
tas y siguiendo las instrucciones contenidas en este
manual.
No toque la máquina con los pies desnudos ni con las
manos o los pies mojados o húmedos.
No desenchufe la máquina tirando el cable, sino toman-
do el enchufe.
No abra el cajón de detergentes mientras la máquina
está en funcionamiento.
No toque el agua de descarga ya que puede alcanzar
temperaturas elevadas.
En ningún caso fuerce la puerta: podría dañarse el
mecanismo de seguridad que la protege de aperturas
accidentales.
En caso de avería, no acceda nunca a los mecanismos
internos para intentar una reparación.
Controle siempre que los niños no se acerquen a la
máquina cuando está en funcionamiento.
Durante el lavado, la puerta tiende a calentarse.
Si debe ser trasladada, deberán intervenir dos o más
personas, procediendo con el máximo cuidado. La
máquina no debe ser desplazada nunca por una sola
persona ya que es muy pesada.
Antes de introducir la ropa controle que el cesto esté
vacío.
Eliminaciones
Eliminación del material de embalaje:
respete las normas locales, de ese modo, los embalajes
podrán volver a ser utilizados.
La norma Europea 2012/19/EU sobre la eliminación de
aparatos eléctricos y electrónicos, indica que los elec-
trodomésticos no deben ser eliminados de la misma
manera que los desechos sólidos urbanos. Los apara-
tos en desuso se deben recoger separadamente para
optimizar el porcentaje de recuperación y reciclaje de
los materiales que los componen e impedir potenciales
daños para la salud y el medio ambiente. El símbolo de
la papelera tachada se encuentra en todos los produc-
tos para recordar la obligación de recolección separada.
Para mayor información sobre la correcta eliminación de
los electrodomésticos, los poseedores de los mismos
podrán dirigirse al servicio público responsable o a los
revendedores.
Apertura manual de la puerta
Si desea sacar la ropa de la lavadora y no es posible abrir
la puerta debido a un corte de energía eléctrica, proceda
del siguiente modo:
1. desenchufe la máquina.
2. verifique que el nivel de
agua en el interior de la
máquina sea inferior al hueco
de la puerta; si no es así, ex-
traiga el agua en exceso uti-
lizando el tubo de descarga
y recogiéndola en un balde
como se indica en la figura.
3. quite el panel de cobertura
delantero de la lavadora con
la ayuda de un destornillador
(ver la figura).
4. utilizando la lengüeta indicada en la figura, tire hacia fuera
hasta liberar la varilla de plástico del retén; posteriormente
tire hacia abajo y simultáneamente abra la puerta.
5. vuelva a montar el panel verificando, antes de empujarlo
hacia la máquina, que los ganchos se hayan introducido en
las correspondientes ranuras.
18
ES
Contenedor de detergentes: para cargar detergentes
y aditivos (ver “Detergentes y ropa”).
Botón ON/OFF : presione brevemente el botón para
encender o apagar la máquina. El piloto START/PAUSE
que centellea lentamente de color verde indica que la
máquina está encendida. Para apagar la lavadora duran-
te el lavado, es necesario mantener presionado el botón
durante más tiempo, aproximadamente 2 seg.; si se
presiona en forma más breve o accidental, la máquina no
se apagará. Si la máquina se apaga durante un lavado en
curso, dicho lavado se anulará.
Mando de PROGRAMAS: para elegir los programas.
Durante el funcionamiento del programa el mando no se
mueve.
Botones con pilotos de FUNCIÓN: para seleccionar las
funciones disponibles. El piloto correspondiente a la fun-
ción seleccionada permanecerá encendido.
Botón CENTRIFUGADO : presiónelo para disminuir o
excluir totalmente el centrifugado - el valor se indica en la
pantalla.
Botón TEMPERATURA : presiónelo para disminuir o
excluir la temperatura; el valor se indica en la pantalla.
Botón COMIENZO RETRASADO : presiónelo para
seleccionar el comienzo retrasado del programa elegido. El
retraso se indicará en la pantalla.
Botón con piloto START/PAUSE : cuando el piloto
verde centellea lentamente, presione el botón para que
comience el lavado. Una vez que el ciclo ha comenzado,
el piloto se mantiene fijo. Para poner en pausa el lavado,
presione nuevamente el botón; el piloto centelleará con
un color anaranjado. Si el símbolo no está iluminado,
se podrá abrir la puerta. Para que el lavado se reanude a
partir del momento en el cual fue interrumpido, presione
nuevamente el botón.
Modalidad de stand by
Esta lavadora está en conformidad con las nuevas norma-
tivas vinculadas al ahorro energético. Está dotada de un
sistema de auto-apagado (stand by) que, en caso de no
funcionamiento, se activa pasados aproximadamente 30
minutos. Presionar brevemente el botón ON-OFF y esperar
que la máquina se active.
Descripción de la lavadora
Panel de control
Botón con
piloto START/
PAUSE
Botón
TEMPERATURA
Botón
CENTRIFUGADO
Mando de
PROGRAMAS
Botones con pilotos
FUNCIÓN
Contenedor de
detergentes
Botón de ON/OFF
PANTALLA
Botón
COMIENZO
RETRASADO
ES
19
Pantalla
La pantalla es útil para programar la máquina y brinda múltiple información.
En la sección A se visualiza la duración de los distintos programas a disposición y, para los que han comenzado, el tiempo
que falta para su finalización; si se hubiera seleccionado un COMIENZO RETRASADO, se visualiza el tiempo que falta para
que comience el programa seleccionado. Además, presionando el botón correspondiente, la máquina muestra automática-
mente la temperatura y la centrífuga máximas previstas para el programa fijado o las últimas seleccionadas si son compati-
bles con el programa elegido.
En la sección B se visualizan las “fases de lavado” previstas para el ciclo seleccionado y, una vez comenzado el programa, la
“fase de lavado” en curso:
Lavado
Aclarado
Centrifugado
Descarga
En la sección C se encuentran, de arriba hacia abajo, los íconos correspondientes a la “temperatura” , al “Comienzo retra-
sado” y al “centrifugado” :
El símbolo iluminado indica que en la pantalla se visualiza el valor seleccionado de “temperatura”.
El símbolo iluminado indica que se ha seleccionado un “Comienzo retrasado”.
El símbolo iluminado indica que en la pantalla se visualiza el valor seleccionado de “centrifugado”.
Símbolo Puerta bloqueada
El símbolo encendido indica que la puerta está bloqueada. Para evitar daños, se debe esperar que el símbolo se apague,
antes de abrir la puerta.
Para abrir la puerta mientras un ciclo está en curso, presione el botón START/PAUSE; si el símbolo PUERTA BLOQUEADA
está apagado, será posible abrir la puerta.
B
CA
20
ES
Cómo efectuar un ciclo de lavado
1. ENCENDER LA MÁQUINA. Presione el botón ; el
piloto START/PAUSE centelleará lentamente de color
verde.
2. CARGAR LA ROPA. Abra la puerta. Cargue la ropa,
cuidando no superar la cantidad de carga indicada en la
tabla de programas de la página siguiente.
3. DOSIFICAR EL DETERGENTE. Extraiga el
contenedor y vierta el detergente en las cubetas
correspondientes como se explica en “Detergentes y
ropa”.
4. CERRAR LA PUERTA.
5. ELEGIR EL PROGRAMA. Seleccione el programa
deseado con el mando de PROGRAMAS; a dicho
programa se le asociará una temperatura y una
velocidad de centrifugado que se pueden modificar. En
la pantalla aparecerá la duración del ciclo.
6. PERSONALIZAR EL CICLO DE LAVADO. Utilice los
botones correspondientes:
Modificar la temperatura y/o el
centrifugado. La máquina muestra automáticamente
la temperatura y la centrífuga máximas previstas para
el programa fijado o las últimas seleccionadas si son
compatibles con el programa elegido. Presionando el
botón se disminuye progresivamente la temperatura
hasta llegar al lavado en frío “OFF”. Presionando el
botón se disminuye progresivamente el centrifugado
hasta su exclusión “OFF”. Si se presionan una vez más
los botones, se volverá a los valores máximos previstos.
Seleccionar un comienzo retrasado.
Para seleccionar el comienzo retrasado del programa
elegido, presione el botón correspondiente hasta
alcanzar el tiempo de retraso deseado. Cuando dicha
opción está activada, en la pantalla aparece el símbolo
. Para eliminar el comienzo retrasado, presione el
botón hasta que aparezca el mensaje OFF.
Modificar las características del ciclo.
Presione el botón para activar la función; el piloto
correspondiente al botón se encenderá.
Presione nuevamente el botón para desactivar la
función; el piloto se apagará.
! Si la función seleccionada no es compatible con el
programa elegido, el piloto centelleará y la función no se
activará.
! Si la función elegida no es compatible con
otra seleccionada precedentemente, el piloto
correspondiente a la primera función seleccionada
centelleará y se activará sólo la segunda, el piloto de la
función activada se iluminará.
! Las funciones pueden variar la carga recomendada
y/o la duración del ciclo.
7. PONER EN MARCHA EL PROGRAMA. Presione
el botón START/PAUSE. El piloto correspondiente se
iluminará de color verde fijo y la puerta se bloqueará
(símbolo PUERTA BLOQUEADA encendido). Para
cambiar un programa mientras un ciclo está en curso,
ponga la lavadora en pausa presionando el botón
START/PAUSE (el piloto START/PAUSE centelleará
lentamente de color anaranjado); luego seleccione el
ciclo deseado y presione nuevamente el botón START/
PAUSE.
Para abrir la puerta mientras un ciclo está en curso,
presione el botón START/PAUSE; si el símbolo PUERTA
BLOQUEADA está apagado, será posible abrir la
puerta. Presione nuevamente el botón START/PAUSE
para reanudar el programa a partir del momento en el
que se había interrumpido.
8. FIN DEL PROGRAMA. En la pantalla aparecerá
el mensaje “END”, cuando el símbolo PUERTA
BLOQUEADA se apague, será posible abrir la puerta.
Abra la puerta, descargue la ropa y apague la máquina.
! Si desea anular un ciclo que ya ha comenzado, presione
más tiempo el botón . El ciclo se interrumpirá y la
máquina se apagará.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60

Indesit IWE 71282 ECO (EU) Guida utente

Categoria
Lavatrici
Tipo
Guida utente