Indesit IWE 71282 ECO (EU) Guida utente

Marca: Indesit

Modello: IWE 71282 ECO (EU)

Categoria: Lavatrici

Tipo: Guida utente

Contents

Installation, 2-3

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Care and maintenance, 4

Cutting off the water or electricity supply

Cleaning the washing machine

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Precautions and tips, 5

General safety

Disposal

Opening the porthole door manually

Description of the washing machine,6-7

Control panel

Display

Running a wash cycle, 8

Wash cycles and options, 9

Table of wash cycles

Wash options

Detergents and laundry, 10

Detergent dispenser drawer

Preparing the laundry

Special wash cycles

Load balancing system

Troubleshooting, 11

Service, 12

IWE 71282

Instructions for use

WASHING MACHINE

English,1

Espańol,13

Portuguęs,25

ΕΛΛΗΝΙΚΑ,37

Български,49

Installation

! This instruction manual should be kept in a safe

place for future reference. If the washing machi-

ne is sold, transferred or moved, make sure that

the instruction manual remains with the machine

so that the new owner is able to familiarise him-

self/herself with its operation and features.

! Read these instructions carefully: they con-

tain vital information relating to the safe instal-

lation and operation of the appliance.

Unpacking and levelling

Unpacking

1. Remove the washing machine from its

packaging.

2. Make sure that the washing machine has

not been damaged during the transportation

process. If it has been damaged, contact the

retailer and do not proceed any further with

the installation process.

3. Remove the 4 pro-

tective screws (used

during transportation)

and the rubber wa-

sher with the cor-

responding spacer,

located on the rear

part of the appliance

(see figure).

4. Close off the holes using the plastic plugs

provided.

5. Keep all the parts in a safe place: you will

need them again if the washing machine ne-

eds to be moved to another location.

! Packaging materials should not be used as

toys for children.

Levelling

1. Install the washing machine on a flat sturdy

floor, without resting it up against walls, furni-

ture cabinets or anything else.

2. If the floor is not

perfectly level, com-

pensate for any une-

venness by tightening

or loosening the

adjustable front feet

(see figure); the angle

of inclination, measu-

red in relation to the

worktop, must not

exceed 2°.

Levelling the machine correctly will provide

it with stability, help to avoid vibrations and

excessive noise and prevent it from shifting

while it is operating. If it is placed on carpet or

a rug, adjust the feet in such a way as to allow

a sufficient ventilation space underneath the

washing machine.

Connecting the electricity and

water supplies

Connecting the water inlet hose

1. Connect the sup-

ply pipe by screwing

it to a cold water tab

using a ¾ gas threa-

ded connection (see

figure).

Before performing the

connection, allow the

water to run freely un-

til it is perfectly clear.

2. Connect the inlet

hose to the washing

machine by screwing

it onto the correspon-

ding water inlet of the

appliance, which is

situated on the top

right-hand side of the

rear part of the ap-

pliance (see figure).

3. Make sure that the hose is not folded over

or bent.

! The water pressure at the tap must fall within

the values indicated in the Technical details

table (see next page).

! If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

! Never use second-hand hoses.

! Use the ones supplied with the machine.

Technical data

Model

IWE 71282

Dimensions

width 59.5 cm

height 85 cm

depth 53,5 cm

Capacity

from 1 to 7 kg

Electrical

connections

please refer to the technical

data plate fixed to the machine

Water

connection

maximum pressure

1 MPa (10 bar)

minimum pressure

0.05 MPa (0.5 bar)

drum capacity 52 litres

Spin speed

up to 1200 rotations per

minute

Test wash

cycles in

accordan-

ce with

directives

1061/2010

and

1015/2010

Programme 3:

Cotton standard 60°C.

Programme 4:

Cotton standard 40°C.

This appliance conforms to

the following EC Directives:

- 2004/108/EC dated

03/05/89 (Electromagnetic

Compatibility)

- 2012/19/EU

- 2006/95/EC Low Voltage)

65 - 100 cm

Connecting the drain hose

Connect the drain

hose, without bending

it, to a drainage duct

or a wall drain located

at a height between

65 and 100 cm from

the floor;

alternatively, rest it on

the side of a washba-

sin or bathtub, faste-

ning the duct sup-

plied to the tap (see

figure). The free end

of the hose should

not be underwater.

! We advise against the use of hose exten-

sions; if it is absolutely necessary, the exten-

sion must have the same diameter as the

original hose and must not exceed 150 cm in

length.

Electrical connections

Before plugging the appliance into the electri-

city socket, make sure that:

• the socket is earthed and complies with all

applicable laws;

• the socket is able to withstand the maximum

power load of the appliance as indicated in

the Technical data table (see opposite);

• the power supply voltage falls within the

values indicated in the Technical data table

(see opposite);

• the socket is compatible with the plug of

the washing machine. If this is not the case,

replace the socket or the plug.

! The washing machine must not be installed

outdoors, even in covered areas. It is extreme-

ly dangerous to leave the appliance exposed

to rain, storms and other weather conditions.

! When the washing machine has been instal-

led, the electricity socket must be within easy

reach.

! Do not use extension cords or multiple sockets.

! The cable should not be bent or compressed.

! The power supply cable must only be repla-

ced by authorised technicians.

Warning! The company shall not be held

responsible in the event that these regulations

are not respected.

The first wash cycle

Once the appliance has been installed, and

before you use it for the first time, run a wash

cycle with detergent and no laundry, using the

wash cycle 2.

Care and maintenance

Cutting off the water and electri-

city supplies

• Turn off the water tap after every wash cycle.

This will limit wear on the hydraulic system

inside the washing machine and help to pre-

vent leaks.

• Unplug the washing machine when cleaning

it and during all maintenance work.

Cleaning the washing machine

The outer parts and rubber components of the

appliance can be cleaned using a soft cloth

soaked in lukewarm soapy water. Do not use

solvents or abrasives.

Cleaning the detergent dispenser

drawer

Remove the dispenser

by raising it and pul-

ling it out (see figure).

Wash it under running

water; this operation

should be repeated

frequently.

Caring for the door and drum of

your appliance

• Always leave the porthole door ajar in order

to prevent unpleasant odours from forming.

Cleaning the pump

The washing machine is fitted with a self-cle-

aning pump which does not require any main-

tenance. Sometimes, small items (such as

coins or buttons) may fall into the pre-chamber

which protects the pump, situated in its bot-

tom part.

! Make sure the wash cycle has finished and

unplug the appliance.

To access the pre-chamber:

1. using a screwdri-

ver, remove the cover

panel on the lower

front part of the wa-

shing machine (see

figure);

2. unscrew the lid

by rotating it anti-

clockwise (see figu-

re): a little water may

trickle out. This is

perfectly normal;

3. clean the inside thoroughly;

4. screw the lid back on;

5. reposition the panel, making sure the hooks

are securely in place before you push it onto

the appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If

there are any cracks, it should be replaced

immediately: during the wash cycles, water

pressure is very strong and a cracked hose

could easily split open.

! Never use second-hand hoses.

Precautions and tips

! This washing machine was designed and constructed in

accordance with international safety regulations. The fol-

lowing information is provided for safety reasons and must

therefore be read carefully.

General safety

• This appliance was designed for domestic use only.

• This appliance can be used by children aged

from 8 years and above and persons with re-

duced physical, sensory or mental capabilities

or lack of experience and knowledge if they

have been given supervision or instruction

concerning use of the appliance in a safe way

and understand the hazards involved. Chil-

dren shall not play with the appliance. Clea-

ning and user maintenance shall not be made

by children without supervision.

• Do not touch the machine when barefoot or with wet or

damp hands or feet.

• Do not pull on the power supply cable when unplugging

the appliance from the electricity socket. Hold the plug

and pull.

• Do not open the detergent dispenser drawer while the

machine is in operation.

• Do not touch the drained water as it may reach extreme-

ly high temperatures.

• Never force the porthole door. This could damage the

safety lock mechanism designed to prevent accidental

opening.

• If the appliance breaks down, do not under any circum-

stances access the internal mechanisms in an attempt

to repair it yourself.

• Always keep children well away from the appliance while

it is operating.

• The door can become quite hot during the wash cycle.

• If the appliance has to be moved, work in a group of two

or three people and handle it with the utmost care. Never

try to do this alone, because the appliance is very heavy.

• Before loading laundry into the washing machine, make

sure the drum is empty.

Disposal

• Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

• The European Directive 2012/19/EU on Waste

Electrical and Electronic Equipment, requires that

old household electrical appliances must not be

disposed of in the normal unsorted municipal waste

stream. Old appliances must be collected separately

in order to optimise the recovery and recycling of the

materials they contain and reduce the impact on human

health and the environment. The crossed out “wheeled

bin” symbol on the product reminds you of your obliga-

tion, that when you dispose of the appliance it must be

separately collected.

Consumers should contact their local authority or

retailer for information concerning the correct

disposal of their old appliance.

Opening the porthole door manually

In the event that it is not possible to open the porthole

door due to a powercut, and if you wish to remove the

laundry, proceed as follows:

1. remove the plug from the

electrical socket.

2. make sure the water level

inside the machine is lower

than the door opening; if it

is not, remove excess water

using the drain hose, collec-

ting it in a bucket as indicated

in the figure.

3. using a screwdriver, remo-

ve the cover panel on the lo-

wer front part of the washing

machine (see figure).

4. pull outwards using the tab as indicated in the figure,

until the plastic tie-rod is freed from its stop position; pull

downwards and open the door at the same time.

5. reposition the panel, making sure the hooks are securely

in place before you push it onto the appliance.

Detergent dispenser drawer: used to dispense

detergents and washing additives (see “Detergents and

laundry”).

ON/OFF button : press this briefly to switch the ma-

chine on or off. The START/PAUSE indicator light, which

flashes slowly in a green colour shows that the machine is

switched on. To switch off the washing machine during the

wash cycle, press and hold the button for approximately 2

seconds; if the button is pressed briefly or accidentally the

machine will not switch off. If the machine is switched off

during a wash cycle, this wash cycle will be cancelled.

WASH CYCLE knob: used to set the desired wash cycle

(see “Table of wash cycles”).

OPTION buttons with indicator light: used to select the

available options. The indicator light corresponding to the

selected option will remain lit.

SPIN button : press to reduce or completely exclude

the spin cycle - the value is indicated on the display.

TEMPERATURE button : press to decrease or comple-

tely exclude the temperature: the value will be shown on

the display.

DELAYED START button : press to set a delayed start

time for the selected wash cycle. The delay time will be

shown on the display.

START/PAUSE button with indicator light: when the

green indicator light flashes slowly, press the button to

start a wash cycle. Once the cycle has begun the indicator

light will remain lit in a fixed manner. To pause the wash

cycle, press the button again; the indicator light will flash

in an orange colour. If the symbol is not illuminated, the

door may be opened. To start the wash cycle from the

point at which it was interrupted, press the button again.

Standby mode

This washing machine, in compliance with new energy sa-

ving regulations, is fitted with an automatic standby system

which is enabled after about 30 minutes if no activity is

detected. Press the ON-OFF button briefly and wait for the

machine to start up again.

Description of the washing

machine

Control panel

TEMPERATURE

Button

Detergent dispenser drawer

OPTION

buttons with

indicator lights

ON/OFF

button

SPIN SPEED

Button

START/PAUSE

button with indicator light

DISPLAY

DELAYED

START Button

WASH CYCLE

knob

Display

The display is useful when programming the machine and provides a great deal of information.

The duration of the available programmes and the remaining time of a running cycle appear in section A; if the DELAY START

option has been set, the countdown to the start of the selected programme will appear. Pressing the relative button, the

machine automatically displays the maximum temperature and spin speed values set for the selected cycle, or the most

recently-used settings if they are compatible with the selected cycle.

The “programme phases” relative to the selected programme and the “programme phase” of the running programme appear

in section B:

Wash

Rinse

Spin

Drain

The icons corresponding to “temperature” , “Programmed start” and “spin” appear in section C from top to bottom:

If the symbol lights up, the display will visualise the set “temperature” value.

When a “delayed start” has been set, the symbol lights up.

If the symbol lights up, the display will visualise the set “spin” value.

Door locked symbol

The lit symbol indicates that the door is locked. To prevent any damage, wait until the symbol turns off before opening the

door.To open the door while a cycle is in progress, press the START/PAUSE button; if the DOOR LOCKED symbol is

switched off the door may be opened.

Running a wash cycle

1. SWITCH THE MACHINE ON. Press the button;

the START/PAUSE indicator light will flash slowly in a

green colour.

2. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed

the maximum load value indicated in the table of

programmes on the following page.

3. MEASURE OUT THE DETERGENT. Pull out the

detergent dispenser drawer and pour the detergent into

the relevant compartments as described in “Detergents

and laundry”.

4. CLOSE THE DOOR.

5. SELECT THE WASH CYCLE. Set the WASH CYCLE

knob to the desired programme; a temperature and

spin speed is set for each wash cycle; these may be

adjusted. The duration of the cycle will appear on the

display.

6. CUSTOMISE THE WASH CYCLE. Use the relevant

buttons:

Modifying the temperature and/or spin

speed. The machine automatically displays the

maximum temperature and spin speed values set for

the selected cycle, or the most recently-used settings

if they are compatible with the selected cycle. The

temperature can be decreased by pressing the

button, until the cold wash “OFF” setting is reached.

The spin speed may be progressively reduced by

pressing the button, until it is completely excluded

(the “OFF” setting). If these buttons are pressed again,

the maximum values are restored.

Setting a delayed start.

To set a delayed start for the selected programme,

press the corresponding button repeatedly until the

required delay period has been reached. When this

option is enabled, the symbol lights up on the

display. To remove the delayed start option press the

button until the text “OFF” appears on the display.

Modifying the cycle settings.

• Press the button to enable the option; the indicator

light corresponding to the button will switch on.

• Press the button again to disable the option; the

indicator light will switch off.

! If the selected option is not compatible with the

programmed wash cycle, the indicator light will flash

and the option will not be activated.

! If the selected option is not compatible with another

option which has been selected previously, the indicator

light corresponding to the first option selected will

flash and only the second option will be activated; the

indicator light corresponding to the enabled option will

remain lit.

! The options may affect the recommended load value

and/or the duration of the cycle.

7. START THE PROGRAMME. Press the START/

PAUSE button. The corresponding indicator light will

become green, remaining lit in a fixed manner, and the

door will be locked (the DOOR LOCKED symbol will

be on). To change a wash cycle while it is in progress,

pause the washing machine using the START/PAUSE

button (the START/PAUSE indicator light will flash slowly

in an orange colour); then select the desired cycle and

press the START/PAUSE button again.

To open the door while a cycle is in progress, press the

START/PAUSE button; if the DOOR LOCKED symbol

is switched off the door may be opened. Press the

START/PAUSE button again to restart the wash cycle

from the point at which it was interrupted.

8. THE END OF THE WASH CYCLE. This will be

indicated by the text “END” on the display; when the

DOOR LOCKED symbol switches off the door may be

opened. Open the door, unload the laundry and switch

off the machine.

! If you wish to cancel a cycle which has already begun,

press and hold the button. The cycle will be stopped

and the machine will switch off.

Wash cycles and options

Wash options

Selecting this option enables you to suitably adjust drum

rotation, temperature and water to a reduced load of lightly

soiled cotton and synthetic fabrics (refer to the “Table of

wash cycles”). “ ” enables you to wash in less time

thereby saving water and electricity. We suggest using a

liquid detergent suitably measured out to the load quantity.

! This function may not be used in conjunction with wash

cycles 1, 2, 7, 8, 9, 10, 11, 12, 13, 14, , .

The function saves energy by not heating the

water used to wash your laundry - an advantage both to

the environment and to your energy bill. Instead, intensified

wash action and water optimisation ensure great wash

results in the same average time of a standard cycle.

For the best washing results we recommend the usage of

a liquid detergent.

! This function may not be used in conjunction with wash

cycles 1, 7, 8, 9, 12, 13, 14, , .

Table of wash cycles

Extra rinse

By selecting this option, the efficiency of the rinse is

increased and optimal detergent removal is guaranteed. It

is particularly useful for sensitive skin.

! This function may not be used in conjunction with wash

cycle .

Easy iron

By selecting this function, the wash and spin cycles will be

modified in order to reduce the formation of creases. At

the end of the cycle the washing machine will perform slow

rotations of the drum; the indicator lights for the EASY IRON

and START/PAUSE options will flash (the first one green, the

second orange). To end the cycle, press the START/PAUSE

button or the EASY IRON button. For the 9,11 wash cycles,

the machine will end the cycle while the laundry is soaking

and the EASY IRON and START/PAUSE indicator lights will

flash. To drain the water so that the laundry may be remo-

ved, press the START/PAUSE button or the EASY IRON

button.

! This function may not be used in conjunction with wash

cycles 8, 12, 13, 14, , .

1) Test wash cycle in compliance with directive 1061/2010: set wash cycle 3 with a temperature of 60°C.

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for

garments which can be washed at 60°C. The actual washing temperature may differ from the indicated value.

2) Test wash cycle in compliance with directive 1061/2010: set wash cycle 4 with a temperature of 40°C.

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for

garments which can be washed at 40°C. The actual washing temperature may differ from the indicated value.

For all Test Institutes:

2) Long wash cycle for cottons: set wash cycle 4 with a temperature of 40°C.

3) Long wash cycle for synthetics: set wash cycle 6; with a temperature of 40°C.

The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors such as water

temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.

Wash cycles

Description of the wash cycle

Max.

temp.

(°C)

Max.

speed

(rpm)

Detergents

Max. load (kg)

Residual

dampness %

Energy

consumption

kWh

Total water lt

Cycle

duration

Prewash

Wash

Fabric

softener

Daily

Cotton with prewash: extremely soiled whites. 90° 1200

  

7 53 2,21 78 170’

Cotton: extremely soiled whites. 90° 1200 -

 

7 53 2,16 72 160’

Cotton Standard 60° (1): heavily soiled whites and resistant colours. 60° 1200 -

 

7 53 1,10 52,5 190’

Cotton Standard 40° (2): lightly soiled whites and delicate colours. 40° 1200 -

 

7 53 1,09 92 185’

Coloured Cottons: lightly soiled whites and delicate colours. 40° 1200 -

 

7 53 0,66 54 90’

Synthetics: heavily soiled resistant colours. 60° 800 -

 

3,5 44 0,93 47 115’

Synthetics (3): lightly soiled resistant colours. 40° 800 -

 

3,5 44 0,57 46 100’

Cotton Standard 20°: lightly soiled whites and delicate colours. 20° 1200 -

 

7 - - - 170’

Special

Wool: for wool, cashmere, etc. 40° 800 -

 

1,5 - - - 70’

Silk/Curtains: for garments in silk and viscose, lingerie. 30° 0 -

 

1 - - - 55’

10 Jeans

40° 800 -

 

3,5 - - - 75’

11 Outwear

30° 400 -



- 2 - - - 60’

Sport

12 Sport Intensive

30° 600 -

 

2,5 - - - 85’

13 Sport Light

30° 600 -

 

2,5 - - - 60’

14 Special Shoes

30° 600 -

 

Max.

2 pairs

- - - 60’

Partial wash cycles

Rinse - 1200 - -



7 - - - 36‘

Spin + Drain - 1200 - - - 7 - - - 16‘

Detergents and laundry

Detergent dispenser drawer

Good washing results also depend on the correct dose of

detergent: adding too much detergent will not necessa-

rily result in a more efficient wash, and may in fact cause

build up on the inside of your appliance and contribute to

environmental pollution.

! Do not use hand washing detergents because these

create too much foam.

! Use powder detergent for white cotton garments, for pre-

washing, and for washing at temperatures over 60°C.

! Follow the instructions given on the detergent packaging.

Open the detergent di-

spenser drawer and pour

in the detergent or washing

additive, as follows.

compartment 1: Pre-wash detergent (powder)

compartment 2: Detergent for the wash cycle

(powder or liquid)

Liquid detergent should only be poured in immediately

prior to the start of the wash cycle.

compartment 3: Additives (fabric softeners, etc.)

The fabric softener should not overflow the grid.

Preparing the laundry

• Divide the laundry according to:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from whites.

• Empty all garment pockets and check the buttons.

• Do not exceed the values listed in the “Table of wash cycles”,

which refer to the weight of the laundry when dry.

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1200 g

1 towel 150-250 g

Special wash cycles

Cotton Standard 20° (wash cycle 7) ideal for lightly soiled

cotton loads. The effective performance levels achieved at

cold temperatures, which are comparable to washing at 40°,

are guaranteed by a mechanical action which operates at

varying speed, with repeated and frequent peaks.

Wool: all wool garments can be washed using programme

8, even those carrying the “hand-wash only” label. For

best results, use special detergents and do not exceed

1,5 kg of laundry.

Silk: use special wash cycle 9 to wash all silk garments.

We recommend the use of special detergent which has

been designed to wash delicate clothes.

Curtains: fold curtains and place them in a pillow case or

mesh bag. Use wash cycle 9.

Jeans: Turn garments inside-out before washing and use

a liquid detergent. Use programme 10.

Outwear (wash cycle 11): is studied for washing water-re-

pellent fabrics and winter jackets (e.g. Gore-Tex, polyester,

nylon); for best results, use a liquid detergent and dosage

suitable for a half-load; pre-treat necks, cuffs and stains if

necessary; do not use softeners or detergents containing

softeners. Stuffed duvets cannot be washed with this

programme.

Sport Intensive (

wash cycle

12): is for washing heavily

soiled sports clothing fabrics (tracksuits, shorts, etc.);

for best results, we recommend not exceeding the ma-

ximum load indicated in the “Table of wash cycles”.

Sport Light (

wash cycle

13): is for washing lightly soiled

sports clothing fabrics (tracksuits, shorts, etc.); for best

results, we recommend not exceeding the maximum

load indicated in the “Table of wash cycles”. We recom-

mend using a liquid detergent and dosage suitable for a

half-load.

Special Shoes (

wash cycle

14): is for washing sports

shoes; for best results, do not wash more than 2 pairs

simultaneously.

Load balancing system

Before every spin cycle, to avoid excessive vibrations and

to distribute the load in a uniform manner, the drum rotates

continuously at a speed which is slightly greater than the

washing rotation speed. If, after several attempts, the load

is not balanced correctly, the machine spins at a reduced

spin speed. If the load is excessively unbalanced, the

washing machine performs the distribution process instead

of spinning. To encourage improved load distribution and

balance, we recommend small and large garments are

mixed in the load.

Troubleshooting

Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure

that the problem cannot be solved easily using the following list.

Problem:

The washing machine does not

switch on.

The wash cycle does not start.

The washing machine does not

take in water (“H2O” will flash on

the display).

The washing machine continuously

takes in and

drains water.

The washing machine does not

drain or spin.

The washing machine vibrates a lot

during the spin cycle.

The washing machine leaks.

The “option” indicator lights and the

“start/pause” indicator light flash and

an error code appears on the display

(e.g.: F-01, F-..).

There is too much foam.

Possible causes / Solutions:

• The appliance is not plugged into the socket fully, or is not making contact.

• There is no power in the house.

• The washing machine door is not closed properly.

• The ON/OFF button has not been pressed.

• The START/PAUSE button has not been pressed.

• The water tap has not been opened.

• A delayed start has been set (see “Running a wash cycle”).

• The water inlet hose is not connected to the tap.

• The hose is bent.

• The water tap has not been opened.

• There is no water supply in the house.

• The pressure is too low.

• The START/PAUSE button has not been pressed.

• The drain hose is not fitted at a height between 65 and 100 cm from the floor

(see “Installation”).

• The free end of the hose is under water (see “Installation”).

• The wall drainage system is not fitted with a breather pipe.

If the problem persists even after these checks, turn off the water tap, switch

the appliance off and contact the Assistance Service. If the dwelling is on one of

the upper floors of a building, there may be problems relating to water drainage,

causing the washing machine to fill with water and drain continuously. Special

anti-draining valves are available in shops and help to avoid this inconvenience.

• The wash cycle does not include draining: some wash cycles require the drain

phase to be started manually.

• The “Easy iron” option has been activated: To complete the wash cycle, press

the START/PAUSE button (see “Wash cycles and options”).

• The drain hose is bent (see “Installation”).

• The drainage duct is clogged.

• The drum was not unlocked correctly during installation (see “Installation”).

• The washing machine is not level (see “Installation”).

• The washing machine is trapped between cabinets and walls (see “Installation”).

• The water inlet hose is not screwed on properly (see “Installation”).

• The detergent dispenser drawer is blocked (for cleaning instructions, see “Care

and maintenance”).

• The drain hose is not fixed properly (see “Installation”).

• Switch off the machine and unplug it, wait for approximately 1 minute and then

switch it back on again.

If the problem persists, contact the Technical Assistance Service.

• The detergent is not suitable for machine washing (it should display the text

“for washing machines” or “hand and machine wash”, or the like).

• Too much detergent was used.

Service

Before calling for Assistance:

• Check whether you can solve the problem alone (see “Troubleshooting”);

• Restart the programme to check whether the problem has been solved;

• If this is not the case, contact an authorised Technical Assistance Centre using the telephone number provided on the

guarantee certificate.

! Always request the assistance of authorised technicians.

Have the following information to hand:

• the type of problem;

• the appliance model (Mod.);

• the serial number (S/N).

This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the

front of the appliance by opening the door.

Español

Sumario

Instalación, 14-15

Desembalaje y nivelación

Conexiones hidráulicas y eléctricas

Primer ciclo de lavado

Datos técnicos

Mantenimiento y cuidados, 16

Interrumpir el agua y la corriente eléctrica

Limpiar la lavadora

Limpiar el contenedor de detergentes

Cuidar la puerta y el cesto

Limpiar la bomba

Controlar el tubo de alimentación de agua

Precauciones y consejos, 17

Seguridad general

Eliminaciones

Apertura manual de la puerta

Descripción de la lavadora, 18-19

Panel de control

Pantalla

Cómo efectuar un ciclo de lavado, 20

Programas y funciones, 21

Tabla de programas

Funciones de lavado

Detergentes y ropa, 22

Contenedor de detergentes

Preparar la ropa

Programas particulares

Sistema de equilibrado de la carga

Anomalías y soluciones, 23

Asistencia, 24

IWE 71282

Manual de instrucciones

LAVADORA

! Es importante conservar este manual para

poder consultarlo en cualquier momento. En

caso de venta, de cesión o de traslado, veri-

fique que permanezca junto con la lavadora

para informar al nuevo propietario sobre el

funcionamiento y brindar las correspondientes

advertencias.

! Lea atentamente las instrucciones: ellas

contienen importante información sobre la

instalación, el uso y la seguridad.

Desembalaje y nivelación

Desembalaje

1. Desembale la lavadora.

2. Controle que la lavadora no haya sufri-

do daños durante el transporte. Si estuviera

dañada no la conecte y llame al revendedor.

3. Quite los 4 tornillos

de protección para el

transporte y la aran-

dela de goma con

el correspondiente

distanciador ubicados

en la parte posterior

(ver la figura).

4. Cubra los orificios con los tapones de plá-

stico suministrados con el aparato.

5. Conserve todas las piezas: cuando la la-

vadora deba ser transportada nuevamente,

deberán volver a colocarse.

! Los embalajes no son juguetes para los

niños.

Nivelación

1. Instale la lavadora sobre un piso plano y

rígido, sin apoyarla en las paredes, muebles ni

en ningún otro aparato.

2. Si el piso no está

perfectamente hori-

zontal, compense las

irregularidades desen-

roscando o enroscan-

do las patas delante-

ras (ver la figura); el

ángulo de inclinación

medido sobre la su-

perficie de trabajo, no

debe superar los 2º.

Una cuidadosa nivelación brinda estabilidad

a la máquina y evita vibraciones, ruidos y

desplazamientos durante el funcionamiento.

Cuando se instala sobre moquetas o alfom-

bras, regule los pies para conservar debajo de

la lavadora un espacio suficiente para la venti-

lación.

Conexiones hidráulicas y eléctri-

cas

Conexión del tubo de alimentación de

agua

1. Conectar el tubo

de tubo enroscándolo

a un grifo de agua fría

con la boca roscada

de 3/4 gas (ver la

figura).

Antes de conectarlo,

haga correr el agua

hasta que esté límpi-

da.

2. Conecte el tubo de

alimentación a la lava-

dora enroscándolo en

la toma de agua cor-

respondiente ubicada

en la parte posterior

derecha (arriba) (ver la

figura).

3. Controle que en el tubo no hayan pliegues

ni estrangulaciones.

! La presión de agua del grifo debe estar com-

prendida dentro de los valores contenidos en

la tabla de Datos técnicos (ver la página corre-

spondiente).

! Si la longitud del tubo de alimentación no es

la suficiente, diríjase a un negocio especializa-

do o a un técnico autorizado.

! No utilice nunca tubos ya usados.

! Utilice los suministrados con la máquina.

Instalación

Conexión del tubo de descarga

Conecte el tubo de

descarga, sin ple-

garlo, a una tubería

de descarga o a una

descarga de pared

colocadas a una altu-

ra del piso entre 65 y

100 cm;

o apóyelo en el borde

de un lavamanos

o de una bañe-

ra, uniendo la guía

suministrada con el

aparato, al grifo (ver

la figura). El extre-

mo libre del tubo de

descarga no debe

permanecer sumergi-

do en el agua.

! No se aconseja utilizar tubos de prolonga-

ción, si fuera indispensable hacerlo, la prolon-

gación debe tener el mismo diámetro del tubo

original y no superar los 150 cm.

Conexión eléctrica

Antes de enchufar el aparato, verifique que:

• la toma tenga la conexión a tierra y haya

sido hecha según las normas legales;

• la toma sea capaz de soportar la carga má-

xima de potencia de la máquina indicada en

la tabla de Datos técnicos (ver al costado);

• la tensión de alimentación esté comprendida

dentro de los valores indicados en la tabla

de Datos técnicos (ver al costado);

• la toma sea compatible con el enchufe de la

lavadora. Si no es así, sustituya la toma o el

enchufe.

! La lavadora no debe ser instalada al aire

libre, ni siquiera si el lugar está reparado, ya

que es muy peligroso dejarla expuesta a la

lluvia o a las tormentas.

! Una vez instalada la lavadora, la toma de

corriente debe ser fácilmente accesible.

! No utilice prolongaciones ni conexiones múl-

tiples.

65 - 100 cm

Datos técnicos

Modelo

IWE 71282

Dimensio-

nes

ancho 59,5 cm

altura 85 cm

profundidad 53,5 cm

Capacidad

de 1 a 7 kg

Conexiones

eléctricas

ver la placa de característi-

cas técnicas aplicada en la

máquina

Conexiones

hídricas

presión máxima

1 MPa (10 bar)

presión mínima

0,05 MPa (0,5 bar)

capacidad del cesto 52 litros

Velocidad de

centrifugado

máxima 1200 r.p.m.

Programas

de control

según las

directivas

1061/2010 y

1015/2010

Programa 3: programa normal

de algodón a 60 °C;

Programa 4: programa normal

de algodón a 40 °C.

Esta máquina cumple con lo

establecido por las siguientes

Directivas de la Comunidad:

- 2004/108/CE (Compatibili-

dad Electromagnética)

- 2012/19/EU

- 2006/95/CE (Baja Tensión)

! El cable no debe estar plegado ni sufrir com-

presiones.

! El cable de alimentación debe ser sustituido

sólo por técnicos autorizados.

¡Atención! La empresa fabricante declina toda

responsabilidad en caso de que estas normas

no sean respetadas.

Primer ciclo de lavado

Después de la instalación y antes del uso,

realice un ciclo de lavado con detergente y sin

ropa, seleccionando el programa 2.

Interrumpir el agua y la corriente

eléctrica

• Cierre el grifo de agua después de cada

lavado. De este modo se limita el desgaste

de la instalación hidráulica de la lavadora y

se elimina el peligro de pérdidas.

• Desenchufe la máquina cuando la debe lim-

piar y durante los trabajos de mantenimiento.

Limpiar la lavadora

La parte externa y las partes de goma se pue-

den limpiar con un paño embebido en agua

tibia y jabón. No use solventes ni productos

abrasivos.

Limpiar el contenedor de deter-

gentes

Extraiga el contene-

dor levantándolo y

tirándolo hacia fuera

(ver la figura).

Lávelo debajo del

agua corriente, esta

limpieza se debe reali-

zar frecuentemente.

Cuidar la puerta y el cesto

• Deje siempre semicerrada la puerta para

evitar que se formen malos olores.

Limpiar la bomba

La lavadora posee una bomba autolimpiante

que no necesita mantenimiento. Pero puede

suceder que objetos pequeños (monedas, bo-

tones) caigan en la precámara que protege la

bomba, situada en la parte inferior de la misma.

! Verifique que el ciclo de lavado haya termina-

do y desenchufe la máquina.

Para acceder a la

precámara:

1. quite el panel que

cubre la parte delan-

tera de la lavadora

con la ayuda de un

destornillador (ver la

figura);

Mantenimiento y cuidados

2. desenrosque la

tapa girándola en

sentido antihorario

(ver la figura): es nor-

mal que se vuelque

un poco de agua;

3. limpie con cuidado el interior;

4. vuelva a enroscar la tapa;

5. vuelva a montar el panel verificando, antes

de empujarlo hacia la máquina, que los gan-

chos se hayan introducido en las correspon-

dientes ranuras.

Controlar el tubo de alimentación

de agua

Controle el tubo de alimentación al menos

una vez al año. Si presenta grietas o rajaduras

debe ser sustituido: durante los lavados, las

fuertes presiones podrían provocar roturas

imprevistas.

! No utilice nunca tubos ya usados.

Precauciones y consejos

! La lavadora fue proyectada y fabricada en conformidad

con las normas internacionales de seguridad. Estas adver-

tencias se suministran por razones de seguridad y deben

ser leídas atentamente.

Seguridad general

• Este aparato ha sido fabricado para un uso de tipo

doméstico exclusivamente.

• Este aparato puede ser utilizado por niños

de 8 años o más y por personas con capa-

cidades físicas, sensoriales o mentales di-

sminuidas o con experiencia y conocimien-

tos insuficientes siempre que sean supervi-

sados o que hayan recibido una adecuada

formación sobre el uso del aparato en forma

segura y conozcan los peligros derivados

del mismo. Los niños no deben jugar con el

aparato. El mantenimiento y la limpieza no

deben ser realizados por niños sin supervi-

sión.

• La lavadora debe ser utilizada sólo por personas adul-

tas y siguiendo las instrucciones contenidas en este

manual.

• No toque la máquina con los pies desnudos ni con las

manos o los pies mojados o húmedos.

• No desenchufe la máquina tirando el cable, sino toman-

do el enchufe.

• No abra el cajón de detergentes mientras la máquina

está en funcionamiento.

• No toque el agua de descarga ya que puede alcanzar

temperaturas elevadas.

• En ningún caso fuerce la puerta: podría dañarse el

mecanismo de seguridad que la protege de aperturas

accidentales.

• En caso de avería, no acceda nunca a los mecanismos

internos para intentar una reparación.

• Controle siempre que los niños no se acerquen a la

máquina cuando está en funcionamiento.

• Durante el lavado, la puerta tiende a calentarse.

• Si debe ser trasladada, deberán intervenir dos o más

personas, procediendo con el máximo cuidado. La

máquina no debe ser desplazada nunca por una sola

persona ya que es muy pesada.

• Antes de introducir la ropa controle que el cesto esté

vacío.

Eliminaciones

• Eliminación del material de embalaje:

respete las normas locales, de ese modo, los embalajes

podrán volver a ser utilizados.

• La norma Europea 2012/19/EU sobre la eliminación de

aparatos eléctricos y electrónicos, indica que los elec-

trodomésticos no deben ser eliminados de la misma

manera que los desechos sólidos urbanos. Los apara-

tos en desuso se deben recoger separadamente para

optimizar el porcentaje de recuperación y reciclaje de

los materiales que los componen e impedir potenciales

daños para la salud y el medio ambiente. El símbolo de

la papelera tachada se encuentra en todos los produc-

tos para recordar la obligación de recolección separada.

Para mayor información sobre la correcta eliminación de

los electrodomésticos, los poseedores de los mismos

podrán dirigirse al servicio público responsable o a los

revendedores.

Apertura manual de la puerta

Si desea sacar la ropa de la lavadora y no es posible abrir

la puerta debido a un corte de energía eléctrica, proceda

del siguiente modo:

1. desenchufe la máquina.

2. verifique que el nivel de

agua en el interior de la

máquina sea inferior al hueco

de la puerta; si no es así, ex-

traiga el agua en exceso uti-

lizando el tubo de descarga

y recogiéndola en un balde

como se indica en la figura.

3. quite el panel de cobertura

delantero de la lavadora con

la ayuda de un destornillador

(ver la figura).

4. utilizando la lengüeta indicada en la figura, tire hacia fuera

hasta liberar la varilla de plástico del retén; posteriormente

tire hacia abajo y simultáneamente abra la puerta.

5. vuelva a montar el panel verificando, antes de empujarlo

hacia la máquina, que los ganchos se hayan introducido en

las correspondientes ranuras.

Contenedor de detergentes: para cargar detergentes

y aditivos (ver “Detergentes y ropa”).

Botón ON/OFF : presione brevemente el botón para

encender o apagar la máquina. El piloto START/PAUSE

que centellea lentamente de color verde indica que la

máquina está encendida. Para apagar la lavadora duran-

te el lavado, es necesario mantener presionado el botón

durante más tiempo, aproximadamente 2 seg.; si se

presiona en forma más breve o accidental, la máquina no

se apagará. Si la máquina se apaga durante un lavado en

curso, dicho lavado se anulará.

Mando de PROGRAMAS: para elegir los programas.

Durante el funcionamiento del programa el mando no se

mueve.

Botones con pilotos de FUNCIÓN: para seleccionar las

funciones disponibles. El piloto correspondiente a la fun-

ción seleccionada permanecerá encendido.

Botón CENTRIFUGADO : presiónelo para disminuir o

excluir totalmente el centrifugado - el valor se indica en la

pantalla.

Botón TEMPERATURA : presiónelo para disminuir o

excluir la temperatura; el valor se indica en la pantalla.

Botón COMIENZO RETRASADO : presiónelo para

seleccionar el comienzo retrasado del programa elegido. El

retraso se indicará en la pantalla.

Botón con piloto START/PAUSE : cuando el piloto

verde centellea lentamente, presione el botón para que

comience el lavado. Una vez que el ciclo ha comenzado,

el piloto se mantiene fijo. Para poner en pausa el lavado,

presione nuevamente el botón; el piloto centelleará con

un color anaranjado. Si el símbolo no está iluminado,

se podrá abrir la puerta. Para que el lavado se reanude a

partir del momento en el cual fue interrumpido, presione

nuevamente el botón.

Modalidad de stand by

Esta lavadora está en conformidad con las nuevas norma-

tivas vinculadas al ahorro energético. Está dotada de un

sistema de auto-apagado (stand by) que, en caso de no

funcionamiento, se activa pasados aproximadamente 30

minutos. Presionar brevemente el botón ON-OFF y esperar

que la máquina se active.

Descripción de la lavadora

Panel de control

Botón con

piloto START/

PAUSE

Botón

TEMPERATURA

Botón

CENTRIFUGADO

Mando de

PROGRAMAS

Botones con pilotos

FUNCIÓN

Contenedor de

detergentes

Botón de ON/OFF

PANTALLA

Botón

COMIENZO

RETRASADO

Pantalla

La pantalla es útil para programar la máquina y brinda múltiple información.

En la sección A se visualiza la duración de los distintos programas a disposición y, para los que han comenzado, el tiempo

que falta para su finalización; si se hubiera seleccionado un COMIENZO RETRASADO, se visualiza el tiempo que falta para

que comience el programa seleccionado. Además, presionando el botón correspondiente, la máquina muestra automática-

mente la temperatura y la centrífuga máximas previstas para el programa fijado o las últimas seleccionadas si son compati-

bles con el programa elegido.

En la sección B se visualizan las “fases de lavado” previstas para el ciclo seleccionado y, una vez comenzado el programa, la

“fase de lavado” en curso:

Lavado

Aclarado

Centrifugado

Descarga

En la sección C se encuentran, de arriba hacia abajo, los íconos correspondientes a la “temperatura” , al “Comienzo retra-

sado” y al “centrifugado” :

El símbolo iluminado indica que en la pantalla se visualiza el valor seleccionado de “temperatura”.

El símbolo iluminado indica que se ha seleccionado un “Comienzo retrasado”.

El símbolo iluminado indica que en la pantalla se visualiza el valor seleccionado de “centrifugado”.

Símbolo Puerta bloqueada

El símbolo encendido indica que la puerta está bloqueada. Para evitar daños, se debe esperar que el símbolo se apague,

antes de abrir la puerta.

Para abrir la puerta mientras un ciclo está en curso, presione el botón START/PAUSE; si el símbolo PUERTA BLOQUEADA

está apagado, será posible abrir la puerta.

Cómo efectuar un ciclo de lavado

1. ENCENDER LA MÁQUINA. Presione el botón ; el

piloto START/PAUSE centelleará lentamente de color

verde.

2. CARGAR LA ROPA. Abra la puerta. Cargue la ropa,

cuidando no superar la cantidad de carga indicada en la

tabla de programas de la página siguiente.

3. DOSIFICAR EL DETERGENTE. Extraiga el

contenedor y vierta el detergente en las cubetas

correspondientes como se explica en “Detergentes y

ropa”.

4. CERRAR LA PUERTA.

5. ELEGIR EL PROGRAMA. Seleccione el programa

deseado con el mando de PROGRAMAS; a dicho

programa se le asociará una temperatura y una

velocidad de centrifugado que se pueden modificar. En

la pantalla aparecerá la duración del ciclo.

6. PERSONALIZAR EL CICLO DE LAVADO. Utilice los

botones correspondientes:

Modificar la temperatura y/o el

centrifugado. La máquina muestra automáticamente

la temperatura y la centrífuga máximas previstas para

el programa fijado o las últimas seleccionadas si son

compatibles con el programa elegido. Presionando el

botón se disminuye progresivamente la temperatura

hasta llegar al lavado en frío “OFF”. Presionando el

botón se disminuye progresivamente el centrifugado

hasta su exclusión “OFF”. Si se presionan una vez más

los botones, se volverá a los valores máximos previstos.

Seleccionar un comienzo retrasado.

Para seleccionar el comienzo retrasado del programa

elegido, presione el botón correspondiente hasta

alcanzar el tiempo de retraso deseado. Cuando dicha

opción está activada, en la pantalla aparece el símbolo

. Para eliminar el comienzo retrasado, presione el

botón hasta que aparezca el mensaje OFF.

Modificar las características del ciclo.

• Presione el botón para activar la función; el piloto

correspondiente al botón se encenderá.

• Presione nuevamente el botón para desactivar la

función; el piloto se apagará.

! Si la función seleccionada no es compatible con el

programa elegido, el piloto centelleará y la función no se

activará.

! Si la función elegida no es compatible con

otra seleccionada precedentemente, el piloto

correspondiente a la primera función seleccionada

centelleará y se activará sólo la segunda, el piloto de la

función activada se iluminará.

! Las funciones pueden variar la carga recomendada

y/o la duración del ciclo.

7. PONER EN MARCHA EL PROGRAMA. Presione

el botón START/PAUSE. El piloto correspondiente se

iluminará de color verde fijo y la puerta se bloqueará

(símbolo PUERTA BLOQUEADA encendido). Para

cambiar un programa mientras un ciclo está en curso,

ponga la lavadora en pausa presionando el botón

START/PAUSE (el piloto START/PAUSE centelleará

lentamente de color anaranjado); luego seleccione el

ciclo deseado y presione nuevamente el botón START/

PAUSE.

Para abrir la puerta mientras un ciclo está en curso,

presione el botón START/PAUSE; si el símbolo PUERTA

BLOQUEADA está apagado, será posible abrir la

puerta. Presione nuevamente el botón START/PAUSE

para reanudar el programa a partir del momento en el

que se había interrumpido.

8. FIN DEL PROGRAMA. En la pantalla aparecerá

el mensaje “END”, cuando el símbolo PUERTA

BLOQUEADA se apague, será posible abrir la puerta.

Abra la puerta, descargue la ropa y apague la máquina.

! Si desea anular un ciclo que ya ha comenzado, presione

más tiempo el botón . El ciclo se interrumpirá y la

máquina se apagará.

La pagina sta caricando ...

Indesit IWE 71282 ECO (EU) Guida utente

Marca: Indesit

Modello: IWE 71282 ECO (EU)

Categoria: Lavatrici

Tipo: Guida utente

Scarica il pdf

rapporto

in altre lingue

español: Indesit IWE 71282 ECO (EU) Guía del usuario
português: Indesit IWE 71282 ECO (EU) Guia de usuario

Altri documenti

Bosch WGG254FWGR/24 Repair Hints