Extreme Networks AP3000X Guida di riferimento
- Categoria
- Antenne di rete
- Tipo
- Guida di riferimento
ExtremeWireless 802.11ax Wi-Fi 6E AP3000X
Indoor Access Point
AP3000X Overview
The AP3000X access point is an indoor model 802.11ax Wi-Fi 6E access point
with external antennas. Out of the four external antennas on the unit, two 6G
external antennas come built-in attached to the unit and cannot be removed.
The other two 2.4G/ 5G antennas are in the box.
For information on antennas that can be purchased separately, see “External
Antenna Information” .
The AP3000X can be mounted on a flat surface such as a wall, solid flat
ceiling, to a junction box or a gang box, and can be installed on a suspended
ceiling or a drop ceiling.
The AP3000X access point has the following features:
• Radios:
– Two 802.11ax radios (one 2X2 2.4GHz and 6 GHz radio, and one 2X2 5
GHz radio)
– One IoT Radio (2.4 GHz)
• Console port: Micro USB
• Two Ethernet ports (Eth0 and Eth1)
– Eth0: 2500/1000/100 Mbps auto-negotiation Ethernet port, RJ45,
Power over Ethernet (PoE) at 802.3at
– Eth1: 1000/100/10 Mbps, RJ45
• One multicolor status light
• One reset button
• One Kensington lock
• One USB 2.0 type A connector
• Power: PoE 802.3af and 802.3at (see Table 1 for details) Antennas: two
external omni-directional 2.4G/5G dual-band antennas, two 6G non-
removable antennas, and one Bluetooth Low Energy (BLE®) antenna
• Temperature: -20°C to +55°C (-4°F to +131°F)
• Enclosure: Plastic
Table 1 AP3000X Power source
Figure 1 AP3000X access point hardware components
Table 2 Side ports on the AP3000X access point
Status LED Activity Description
The AP3000X access point has one status light on top of the chassis that
shows operational states for system power, firmware updates, Ethernet and
wireless interface activity, and major alarms.
• Steady white: The device has successfully established a Control And
Provisioning of Wireless Access Points (CAPWAP) connection to
ExtremeCloud IQ and is operating normally.
• Slow-blinking white: The device has a CAPWAP connection to
ExtremeCloud IQ but is operating on 802.3af power instead of 802.3at
power.
• Steady amber: The device is initializing, rebooting, or is running without a
CAPWAP connection.
• Slow-blinking amber: The device has no CAPWAP connection to
ExtremeCloud IQ and is operating on 802.3af power instead of 802.3at
power.
Power source Description
Power over Ethernet (PoE)
Power is provided through the 2.5G Ethernet port of
AP3000X, compliant to be powered with 802.3af and
802.3at to provide full functionality. For reduced
functionality, use 802.3af.
External 12V DC power supply
(optional; ordering part
#37215- PWR 12VDC/2A,
2.5mm x 5.5mm connector)
Power is provided through an external DC power
supply plugged into an AC source.
Callout Description
1 Kensington security slot
2 USB port
3 Console port
4 12VDC power
5 ETH1
6 ETH0 and PoE+
• Fast-blinking amber: The device is upgrading its IQ Engine firmware.
• Dark: power is off.
AP3000X Box Contents
Ensure that the following items are available:
All optional brackets and accessories are sold separately. For installation
instructions about all mounting procedures, see ExtremeWireless Access Point
AP3000X Installation Guide in the Extreme Networks Documentation Support
site.
Install the Access Point
Use these instructions as guidelines for mounting and connecting the
AP3000X access point easily and safely. The AP3000X comes with the AH-
ACC-BKT-AX-TB mounting bracket that can be used to mount the access point
on flat surfaces such as solid flat ceilings or wood walls.
Install the Access Point on a Wall or a Flat Ceiling
Use the AH-ACC-BKT-AX-TB mounting bracket for flat surface wall or solid
ceiling installation.
Pre-installation checklist:
The following hardware is required for installing the AH-ACC-BKT-AX-TB
accessory on a wall or a solid ceiling:
• An AP3000X access point
• One AH-ACC-BKT-AX-TB mounting bracket
• Two M3.5 pan head wood screws and two screw-in anchors
1 Using the AH-ACC-BKT-AX-TB mounting bracket as a template, mark and
drill two mounting holes.
2 Attach the bracket to the wall using two M3.5 pan head wood screws. Use
push-in anchors or screw-in anchors for drywall or plastic board
installations on vertical walls.
3 Attach the AP to the bracket. Align the red dot on the bracket and the AP.
4 Press and rotate the access point 1/8 turn clockwise until it clicks into place.
5 Attach the Cat5e RJ45 cable to the ETH0 port on the access point.
Install the Access Point on a Non-Standard Ceiling
Grid or a Wall
For non-standard ceiling grid installation or wall installation instructions, see
Wi-Fi 6 802.11ax Access Points Accessories Guide.
The AP can be installed on a non-standard ceiling grid with the following
accessories:
Table 4 Non-standard ceiling grid and wall accessories information
Table 3 Contents of the AP3000X Box
Quantity Item
1 AP3000X access point
1 AP3000X Quick Reference
1 AH-ACC-BKT-AX-TB mounting bracket
2 Phillips pan head wood screws
2 Screw-in anchors
2 2.4 GHz/5 GHz external antennas
Electrical Hazard: Only qualified personnel should perform installation
procedures.
Note: The mounting procedures for installing the access point to non-standard
ceilings are covered in the ExtremeWireless Access Point AP3000X Installation
Guide.
Note: The wood screws and screw-in anchors come in a separate plastic bag.
Note: Screw-in anchors must be used for ceiling installations.
Note: For wall installation, the ‘E’ logo must be on the left side of the access
point as shown in Figure 3.
Bracket part number Description
AH-ACC-BKT-AX-TB Mounting bracket for Prelude ceilings (15/16 in. ceiling grid),
Suprafine ceilings (9/16 in. ceiling grid), and walls. The ceiling tile
sides must be flat
AH-ACC-BKT-AX-IL Mounting bracket for Interlude (9/16 wide T-bar with protrusion)
ceilings
AH-ACC-BKT-AX-SL Mounting bracket for Silhouette ceilings (ceiling grid with 1/8 in.
or 1/4 in. bottom opening)
Lock the Access Point after Installation
Use the Kensington slot on the side of the AP to secure it. The slot prevents
someone from removing the AP from the mounting accessory.
External Antenna Information
The AP3000X access point comes with four external antenna connectors. It is
compatible with the ML-2452-APA2-02 and ML-2452-HPAG5A8-01 antennas.
Figure 2 AP3000X external antenna port connectors
Table 5 AP3000X external antenna ports radio information
Table 6 AP3000X radio ports support information
Professional Installation Instruction
Installation personnel
This product is designed for specific application and needs to be installed by a
qualified personnel who has RF and related rule knowledge. The general user
shall not attempt to install or change the setting.
Installation procedure
Refer to the ExtremeWireless Access Point AP3000X Installation Guide.
Instructions d'installation professionnelle
Installation
Ce produit est destine a un usage specifique et doit etre installe par un
personnel qualifie maitrisant les radiofrequences et les regles s'y rapportant.
L'installation et les reglages ne doivent pas etre modifies par l'utilisateur final.
Procedure d'installation
Consulter le manuel d'utilisation ExtremeWireless Access Point AP3000X Installation
Guide.
Regulatory and Compliance Information
Safety Guidelines
This section contains notices that are intended to protect your personal safety and
to prevent damage to the equipment.
ACC-BKT-AX-JB Junction box or wall mounting for indoor APs.
ACC-BKT-AX-BEAM Beam mounting for indoor access points
AH-ACC-BKT-AX-WL Mounting bracket for direct-to-wall installations when a 1.25
inches of space is desired between the wall and the access point
Note: The default bracket for wall installation is the ACC-BKT-AX-JB bracket.
Order the -JB bracket for new wall installations. The AH-ACC-BKT-AX-WL
bracket is for users who already have the -WL brackets.
Note: The ML-2452-APA2-02 and ML-2452-HPAG5A8-01 antennas are
purchased separately.
The ML-2452-HPAG5A8-01 antenna requires the 25-85392-01R adapter for
mounting.
Radio modes
Antenna ports
Radio port (2.4G/5G) Radio port (6G)
1 2.4G and 5G -
2 5G 6G
Radio port Antenna type
2.4 GHz/5 GHz Dual-band omni
6 GHz Omni
Note: For antenna specifications and installation information, see the Wi-Fi 6
(802.11ax) Antenna Specifications Guide.
Warning: Select the installation position and ensure that the final output
power does not exceed the limit set forth in relevant rules. The violation of the
rule could lead to serious federal penalty.
Warning: Avertissement: Choisir avec soin la position d'installation et
s'assurer que la puissance de sortie ne depasse pas les limites en vigueur. La
violation de cette regle peut conduire a de serieuses penalites federales.
Bracket part number Description Qualified Personnel:
Federal Communications Commission (FCC) Notice
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Operation in the band 5925-7125MHz subject to, (1) FCC regulations restrict the
operation of this device to indoor use only, (2) the operation of this device is
prohibited on oil platforms, cars, trains, boats, and aircraft, except that operation of
this device is permitted in large aircraft while flying above 10,000 feet, and (3)
operation of transmitters in the 5.925 GHz - 7.125 GHz band is prohibited for control
of or communications with unmanned aircraft systems.
Conformitè Europëenne (CE) Information
The device is restricted to indoor use only when operating in the 5150 to 5350 MHz
frequency range.
Selling Countries:
CE Marking and European Area (EEA)
Other Countries
Brazil
Este produto está homologado pela ANATEL, de acordo com os procedimentos
regulamentados pela Resolução n°. 242/2000 e atende aos requisitos técnicos
aplicados.
Este equipamento não tem direito à proteção contra interferência prejudicial e não
pode causar interferência em sistemas devidamente autorizados. Para maiores in-
formações, consulte o site da ANATEL – www.anatel.gov.br
Mexico Compliance Statement
La operacion de este equipo esta sujeta a las siguientes dos condiciones
1 es posible que este equipo o dispositivo no cause interferencia perjudicial y
2 este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que
pueda causar su operacion no deseada.
The operation of this equipment is subject to the following two conditions:
1 It is possible that this equipment or device does not cause disruptive interference
and
2 This equipment or device must accept any interference, including interference
that may cause undesired operation.
Electrical Hazard: Only qualified personnel should perform installation
procedures. Within the context of the safety notes in this documentation,
qualified persons are defined as persons who are authorized to commission,
ground and label devices, systems, and circuits in accordance with established
safety practices and standards. A qualified person understands the
requirements and risks involved with installing outdoor electrical equipment in
accordance with national codes.
Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
FCC Radiation Exposure Statement: This equipment complies with FCC
radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance of 47 cm
between the radiator and your body.
Warning: CE co-location MPE Statement: This equipment complies with CE
radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance of 20 cm
between the radiator and your body.
AT BE BG HR CY CZ DK
EE FI FR DE EL HU IE
IT LV LT LU MT NL PL
PT RO SK SI ES SE UK
(NI)
Warning: This is a Class B product. In a domestic environment, this product
may cause radio interference in which case the user may be required to take
adequate measures.
ExtremeWirelessTM
Indoor Access Point
Quick Reference
AP3000X
Scan to Download the
ExtremeCloud IQ Companion Mobile Application
Commission, monitor, and troubleshoot devices easily with ExtremeCloud IQ
Companion Mobile Application (supported on iOS and Android).
Use your mobile device camera to scan the serial number, capture installation
images, assign or change device location, and network policy. The
ExtremeCloud IQ Companion Mobile Application enables you to access the
device CLI for troubleshooting and view device and client status
.
ExtremeCloud IQ Companion ExtremeCloud IQ Companion
iOS Mobile Application Android Mobile Application
Scan for Product Support Details
ExtremeCloud IQ Companion Documentation
Mobile Application Onboarding
Notice
Copyright © 2023 Extreme Networks, Inc. All Rights Reserved.
Legal Notices
Extreme Networks, Inc. reserves the right to make changes in specifications
and other information contained in this document and its website without
prior notice. The reader should in all cases consult representatives of Extreme
Networks to determine whether any such changes have been made.
The hardware, firmware, software or any specifications described or referred
to in this document are subject to change without notice.
Trademarks
Extreme Networks and the Extreme Networks logo are trademarks or
registered trademarks of Extreme Networks, Inc. in the United States and/or
other countries.
All other names (including any product names) mentioned in this document
are the property of their respective owners and may be trademarks or
registered trademarks of their respective companies/owners.
For additional information on Extreme Networks trademarks, please see:
www.extremenetworks.com/company/legal/trademarks/
Documentation, Installation Videos, and Support
For product support, including Documentation and Installation Videos, visit:
www.extremenetworks.com/documentation
UK Statement and CE Statement
This equipment complies with the UK and EEA radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and operated
with minimum distance of 20 cm between the radiator and your body.
The frequency and the maximum transmitted power in the UK and European
Conformity are listed below:
CE - The device is restricted to indoor use only when operating in the 5945 to 6425
MHz frequency range.
UK - The device is restricted to indoor use only when operating in the 5945 to 6425
MHz frequency range.
Hereby, Extreme Networks declares that the radio equipment AP3000X-WW is in
compliance with Radio Equipment Regulations 2017.
Operation on oil platforms, cars, trains, boats, and aircraft shall be prohibited
except for on large aircraft flying above 10,000 ft.
For full text of the UK Declaration of Conformity, please contact Extreme
Regulatory Compliance at compliancerequest@extremenetworks.com.
Extreme Networks UK Address
Extreme Networks, UK Ltd.
250 Longwater Avenue Green Park
1st Floor
Reading, UK
Extreme Networks EU Importer Address
Extreme Networks, Ireland Ops Ltd.
Rineanna House Shannon Industrial Estate
Shannon, V14CA36
Ireland
Industry Canada Notice
This device contains license-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada's license-exempt RSS(s).
Operation in the band 5925 to7125 MHz is subject to the following two conditions:
(1) IC regulations restrict the operation of this device to indoor use only, and (2) the
operation of this device is prohibited on oil platforms, cars, trains, boats, and
aircraft, except that operation of this device is permitted in large aircraft while
flying above 10,000 feet.
Cet appareil contient un ou des émetteurs/récepteurs exempts de licence
conformes aux RSS exempts de licence d'Innovation, Sciences et Développement
économique Canada. Fonctionnement dans la bande 5925 à 7125 MHz sous réserve
des deux conditions suivantes: (1) Les réglementations de la IC limitent le
fonctionnement de cet appareil à une utilisation en intérieur uniquement, et (2) le
fonctionnement de cet appareil est interdit sur les plates-formes pétrolières, les
voitures, les trains, les bateaux et les avions, sauf que le fonctionnement de cet
appareil est autorisé dans de grandes avion en vol au-dessus de 10 000 pieds.
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions:
1 This device may not cause interference.
2 This device must accept any interference, including interference that may cause
undesired operation of the device.
L’émetteur/récepteur exempt de license contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences et Développement économique Canada
applicables aux appareils radio exempts de license. L’exploitation est autorisée aux
deux conditions suivantes :
1 L’appareil ne doit pas produire de brouillage;
2 L’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
This radio transmitter [IC ID: 4141B-AP3000] has been approved by Innovation,
Science and Economic Development Canada to operate with the antenna types
CE UK
2400-2483.5 MHz: 19.98 dBm 2400-2483.5 MHz: 19.98 dBm
2400-2483.5 MHz(802.15.4): 8.03 dBm 2400-2483.5 MHz(802.15.4): 8.03 dBm
2400-2483.5 MHz (BLE®): 8.0 dBm 2400-2483.5 MHz (BLE®): 8.0 dBm
5150-5725 MHz: 29.96 dBm 5150-5725 MHz: 29.96 dBm
5725-5850MHz: 13.97 MHz 5720-5850 MHz: 29.97 dBm
5945-6425 MHz: 22.99 dBm 5945-6425 MHz: 22.99 dBm
Caution: The device for operation in the band 5150-5250 MHz is only for
indoor use to reduce the potential for harmful interference to co-channel
mobile satellite systems.
Caution: Avertissement: les dispositifs fonctionnant dans la bande 5150-
5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de
réduire les risques de brouillage préjudiciable aux systèmes de satellites
mobiles utilisant les mêmes canaux.
Caution: This equipment complies with IC RSS-102 radiation exposure limits
set forth for an uncontrolled environment. This equipment must be installed
and operated with minimum distance 28 cm between the radiator and your
body.
Caution: Avertissement:Cet équipement est conforme aux limites
d’exposition aux rayonnements IC établies pour un environnement non
contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 28cm
de distance entre la source de rayonnement et votre corps.
listed below, with the maximum permissible gain indicated. Antenna types not
included in this list that have a gain greater than the maximum gain indicated for
any type listed are strictly prohibited for use with this device.
Cet émetteur radio [IC ID: 4141B-AP3000] a été approuvé par Innovation, Sciences
et Développement économique Canada pour fonctionner avec les types d'antenne
répertoriés sous, avec le gain maximal autorisé indiqué. Les types d'antenne non
inclus dans cette liste qui ont un gain supérieur au gain maximum indiqué pour tout
type répertorié sont strictement interdits pour une utilisation avec cet appareil.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance of 28 cm between the radiator and your body.
Cet équipement est conforme aux limites d'exposition aux rayonnements IC RSS-
102 établies pour un environnement non contrôlé. Cet équipement doit être installé
et utilisé avec une distance minimale de 28 cm entre le radiateur et votre corps.
Taiwan Regulatory Statement
請至此連結閱讀中文說明: https://www.extremenetworks.com/support/docu-
mentation/.
European Waste Electrical and Electronic Equipment
(WEEE) Notice
In accordance with Directive 2012/19/EU of the European Parliament on waste
electrical and electronic equipment (WEEE):
1 The symbol above indicates that separate collection of electrical and electronic
equipment is required.
2 When this product has reached the end of its serviceable life, it cannot be
disposed of as unsorted municipal waste. It must be collected and treated
separately.
3 It has been determined by the European Parliament that there are potential
negative effects on the environment and human health as a result of the
presence of hazardous substances in electrical and electronic equipment.
4 It is the users’ responsibility to utilize the available collection system to ensure
WEEE is properly treated. For information about the available collection system,
please contact Extreme Environmental Compliance at
Antenna
type/Type
d'antenne
Frequency range
(GHz)/Gamme de
fréquences (GHz)
Antenna
gain (dBi)/
Gain
d'antenne
(dBi)
Impedance (Ohm)/Impédance
(Ohm)
Dipole 2.4/5 3.04/4.96 50
Dipole 2.4/5 3.04/4.96 50
Dipole 2.4/5 3.23/5.22 50
Dipole 2.4/5 3.23/5.22 50
Omni 2.4/5 5/8 50
Omni 2.4/5 5/8 50
Panel 2.4/5 7.5/7.5 50
Panel 2.4/5 2.97/4.94 50
Panel 2.4/5 2.94/4.62 50
Dipole 6 5.49 50
Dipole 6 5.49 50
PIFA 2.4 4.02 50
Supplement to Product Instructions
Declaration of Conformity in Languages of the European
Community
English Hereby, Extreme Networks, declares that the radio equipment type (AP3000X-
WW) is in compliance with Directive 2014/53/EU. For full text of the EU
Declaration of Conformity, please contact Extreme Regulatory Compliance at
compliancerequest@extremenetworks.com
Finnish Täten Extreme Networks vakuuttaa, että Radio laite tyyppi (AP3000X-WW) on
direktiivin 2014/53/EU mukainen.EU vaatimustenmukaisuusvakuutuksen
täydellisestä tekstistä ota yhteyttä äärimmäisiin viranomais säädöksiin
osoitteessa compliancerequest@extremenetworks.com
Dutch Extreme Networks verklaart hierbij dat het type radioapparatuur (AP3000X-
WW) in overeenstemming is met richtlijn 2014/53/EU.Voor de volledige tekst
van de EU-conformiteitsverklaring u contact opnemen met extreme
regelgeving op compliancerequest@extremenetworks.com
French Par la présente, Extreme Networks déclare que le type d'équipement radio
(AP3000X-WW) est conforme à la directive 2014/53/UE.Pour le texte intégral
de la Déclaration de conformité de l'UE, veuillez communiquer avec Extreme
Regulatory Compliance à compliancerequest@extremenetworks.com
Swedish Härmed intygar Extreme Networks att radioutrustning typ (AP3000X-WW)
överensstämmer med direktiv 2014/53/EU.För fullständig text av EU-försäkran
om överensstämmelse, vänligen kontakta Extreme regelefterlevnad på
compliancerequest@extremenetworks.com
Danish Herved erklærer Extreme Networks, at radioudstyrs typen (AP3000X-WW) er i
overensstemmelse med direktiv 2014/53/EU.For den fulde ordlyd af EU-
overensstemmelseserklæringen bedes du kontakte Extreme Regulatory
Compliance på compliancerequest@extremenetworks.com
German Dabei erklärt Extreme Networks, dass der Funkgerätetyp (AP3000X-WW) mit
der Richtlinie 2014/53/EU im Einklang steht.Für den vollständigen Wortlaut der
EU-Konformitätserklärung wenden Sie sich bitte an extreme Regulatory
Compliance unter compliancerequest@extremenetworks.com
Greek Με την παρούσα, ακραία δίκτυα δηλώνουν ότι ο τύπος του ραδιοεξοπλισμού
(AP3000X-WW) συμμορφώνεται με την οδηγία 2014/53/ΕΕ.Για το πλήρες
κείμενο της δήλωσης συμμόρφωσης ΕΕ, παρακαλούμε επικοινωνήστε με
την ακραία κανονιστική συμμόρφωση στο
compliancerequest@extremenetworks.com
Icelandic Hérlendis, Extreme Networks, lýsa því yfir að útvarpsbúnaðargerðin (AP3000X-
WW) sé í samræmi við tilskipun 2014/53/ESB.Fyrir fullan texta í ESB yfirlýsingu
um samræmi, vinsamlegast hafðu samband við Extreme Reglufylgni á
compliancerequest@extremenetworks.com
Italian Di conseguenza, Extreme Networks dichiara che il tipo di apparecchiature radio
(AP3000X-WW) è conforme alla direttiva 2014/53/EU.Per il testo integrale della
Dichiarazione di conformità dell'UE, contattare Extreme Regulatory Compliance
presso compliancerequest@extremenetworks.com
Spanish Por la presente, Extreme Networks declara que el tipo de equipo radioeléctrico
(AP3000X-WW) cumple con la Directiva 2014/53/UE.Para obtener el texto
completo de la Declaración de conformidad de la UE, póngase en contacto con
Extreme Regulatory Compliance en compliancerequest@extremenetworks.com
Portuguese Por este meio, a Extreme Networks declara que o tipo de equipamento de rádio
(AP3000X-WW) está em conformidade com a Diretiva 2014/53/UE.Para obter
o texto integral da Declaração de Conformidade da UE, contacte o
cumprimento regulamentar extremo em
compliancerequest@extremenetworks.com
Malti B ' dan, netwerks estremi, jiddikjara li t-tip ta ' tagħmir tar-radju (AP3000X-
WW) huwa konformi mad-Direttiva 2014/53/UE.Għat-test sħiħ tad-dikjarazzjoni
ta ' konformità tal-UE, jekk jogħġbok ikkuntattja lill-konformità regolatorja
compliancerequest@extremenetworks.com
P/N 9037548-00 Rev AC
-
1
-
2
Extreme Networks AP3000X Guida di riferimento
- Categoria
- Antenne di rete
- Tipo
- Guida di riferimento