Yamaha MY16 Manuale utente

Marca: Yamaha

Modello: MY16

Categoria: Mixer audio

Tipo: Manuale utente

Questo manuale è adatto anche per

DUGAN-MY16

Dugan-MY16 User Guide

Automatic Mixing Controller Card

for Yamaha Digital Mixers

Release Date December 2013

Version 2.7

Author Rob Wenig

Important Safety Instructions and Warnings

The Dugan-MY16’s circuitry is made in the USA and meets applicable national safety

standards.

Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. WARNING! To reduce the risk of fire or electric shock, do not expose this appa-

ratus to rain or moisture.

7. Clean only with dry cloth.

8. Do not block any ventilation openings. Install in accordance with the manufac-

turer’s instructions.

9. Do not install near any heat sources such as radiators, heat registers, stoves, or

other apparatus (including amplifiers) that produce heat.

10. Only use attachments/accessories specified by the manufacturer.

11. Unplug this apparatus during lightning storms or when unused for long periods

of time.

12. WARNING! Refer all servicing to qualified service personnel. Servicing is re-

quired when the apparatus has been damaged in any way, such as liquid has been

spilled or objects have fallen into the apparatus, the apparatus has been exposed

to rain or moisture, does not operate normally, or has been dropped.

13. WARNING! No user serviceable parts inside.

FCC

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when in-

stalled as indicated in the instructions contained in this manual, meets FCC re-

quirements. Modifications not expressly approved by Dan Dugan Sound Design

may void your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/or another

product use only high quality shielded cables. Failure to follow instructions could

void your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the requirements

listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with

these requirements provides a reasonable level of assurance that your use of this

product in a residential environment will not result in harmful interference with

other electronic devices. This equipment generates/uses radio frequencies and, if

not installed and used according to the instructions found in the users manual,

may cause interference harmful to the operation of other electronic devices.

Compliance with FCC regulations does not guarantee that interference will not

occur in all installations.

If this product is found to be the source of interference, which can be determined

by turning the host unit OFF and ON, please try to eliminate the problem by using

one of the following measures: Relocate either this product or the device that is be-

ing affected by the interference. Utilize power outlets that are on different branch

(circuit breaker or fuse) circuits or install AC line filter/ s. In the case of radio or

TV interference, relocate/ reorient the antenna. If the antenna lead-in is 300 ohm

ribbon lead, change the lead-in to co-axial type cable. If these corrective measures

do not produce satisfactory results, please contact the local retailer authorized to

distribute this type of product. If you can not locate the appropriate retailer, please

contact Dan Dugan Sound Design.

The above statements apply ONLY to those products manufactured by Dan Dugan

Sound Design.

This device complies with Part 15 of the FCC Rules. Operation is subject to the fol-

lowing two conditions:

1. This device may not cause harmful interference.

- AND -

2. This device must accept any interference received, including interference that

may cause undesired operation.

This Class B digital apparatus complies with Canadian ICES-003.

Precautions

Failure to observe the following warnings may lead to fatality or serious injury from

fire or electric shock.

1. Before installing the card, you must refer to the owner’s manual of the host device

or to the Yamaha website (“Guidance on the use of Mini-YGDAI cards” page) to

verify that your host device supports this card, and to verify the number of cards

that can be installed in combination with other Yamaha or third-party cards.Ya-

maha website: http://www.yamahaproaudio.com/

2. If one or more cards in a combination not endorsed by Yamaha are installed in a

Yamaha device, electrical shock, fire, or malfunction may occur. Please note that

the Dugan-MY16 can be used with the following models of Yamaha product that

accept option I/O cards (Yamaha MY series and third-party products):

PM5D/PM5D-RH, DSP5D, M7CL-48ES, M7CL-48, M7CL-32, MTX5-D, LS9-32,

LS9-16, DM2000, DM1000, 02R96, 01V96, DME64N, DME24N, CL1, CL3, CL5.

3. To use the Dugan-MY16 card in a DM2000 or 02R96, the following system soft-

ware is required: DM2000 Version 1.14 or later. 02R96 Version 1.06 or later. See

the Yamaha Web site for upgrade information.

4. Do not attempt to disassemble or modify the card. Do not apply excessive force

to board connectors or other board components. Mishandling the board may

lead to shock, fire hazard, or equipment failure.

5. To eliminate shock hazard, disconnect the power cable from the main unit before

installing this card.

CAUTION: Failure to observe the following precautions may lead to personal injury, or may result in

damage to equipment or other property.

6. Do not touch the board’s metallic leads (pins) when handling the card. Pins are

sharp and may cause hand cuts.

7. The card is electrostatic-sensitive. Before handling the card, you should briefly

touch the main unit’s metal casing with your bare hand to drain any static charge

from your body.

CAUTION: Dan Dugan Sound Design assumes no responsibility for data loss, equipment damage, or

injury caused by inappropriate handling or usage.

Warranty Statement

Dan Dugan Sound Design warrants that Dugan-MY16 hardware will be free from defects

in components and workmanship for a period of 12 months from the date of invoice.

During the warranty period, Dan Dugan Sound Design will cover the cost of all parts

and labor to remedy the defect, or replace products which prove to be defective.

Dan Dugan Sound Design is not obliged to honor this warranty if the hardware has

failed to be maintained and operated as specified by Dan Dugan Sound Design, in the

accompanying documentation, or other than in accordance with industry standards.

Defects caused by unauthorized modifications, misuse, negligence, act of God or ac-

cident are not covered by this warranty.

Software is provided as a convenience, but due to the wide variety of computer sys-

tems, cannot be guaranteed to work. This Limited Warranty is exclusive and no other

warranty is expressed or implied. Dan Dugan Sound Design does not warrant that D an

Dugan Sound Design software, or any third-party software, is error free.

Dugan-MY16 User Guide

Table of Contents

Chapter 1: Introduction ............................................................................................. 9

Theory of Operation................................................................................. 10

Remote Control and Software............................................................. 11

Chapter 2: Installation and Linking................................................................. 13

Installing the Dugan-MY16 Card ........................................................ 13

Choose an Operating Mode ................................................................ 14

Connecting to a Computer or Network ............................................ 16

Linking Multiple Dugans........................................................................ 21

Chapter 3: The Dugan Control Panel ............................................................. 23

Top Pane...................................................................................................... 24

Add Units Manually.............................................................................. 24

Select Units to Display ........................................................................ 25

Setting Controls ........................................................................................ 25

Naming Units and Channels................................................................. 26

Channel Pane ............................................................................................ 26

Level Indicator...................................................................................... 27

Bypass .................................................................................................. 28

Channel Modes .................................................................................... 28

Preset .................................................................................................. 29

Channel Groups.................................................................................... 30

Channel Override ................................................................................. 30

Meters .................................................................................................. 31

Weight .................................................................................................. 31

Dugan-MY16 User Guide

Master Pane ............................................................................................... 34

Indicators .............................................................................................. 34

Controls................................................................................................. 36

Typical Operation...................................................................................... 38

Muting Mics on an LS9 .......................................................................... 39

Chapter 4: Updates..................................................................................................... 41

Chapter 5: Specifications....................................................................................... 43

Dugan-MY16 User Guide

Chapter 1: Introduction

The Dugan-MY16 is a 16-channel automatic mixing controller that plugs into a slot

on Yamaha digital mixers. This multichannel audio signal processor patches into the

Yamaha’s mic channel insert points. The MY16 detects which mics are being used,

and makes fast, transparent crossfades. This eliminates late upcuts, reduces system

noise and feedback, and lets the engineer focus on balance and sound quality.

The Dugan-MY16 enhances a diverse group of live applications that require multiple

mics:

• Conference reinforcement, video trucks

• Houses of worship

• Film and television dialogue, reality shows

• Theater

• Boardrooms, civic meetings, community TV

• Teleconferencing and distance learning

The Dugan-MY16 is operated from the Dugan Control Panel for Java (included). The

Dugan Control Panel for iPad (sold separately) performs the same function on an iPad.

Dugan-MY16 User Guide

Theory of Operation

The Dugan-MY16 uses the Dugan Speech System™, a patented and trademarked

automatic mixing function that distributes the gain of one open microphone over

the entire system. This results in a natural one-mic ambience with minimal noise

or feedback. The Dugan Speech System does not limit, compress, or control levels. It per-

forms just one critical function: cuing multiple live mics in situations with unpre-

dictable dialogue. It is essential to distinguish this behavior from the distracting

fluctuation of levels and uneven ambience produced by a conventional noise gate.

When one person talks at a time, the Dugan Speech System rapidly fades that mic’s

gain up and the others down. When the speaker pauses, that mic fades down and the

others up, so the gain of all mics sums to equal that of one mic at full gain. When

the next person talks, the system fades that mic’s gain up and the others down. The

result sounds like passing one mic among several speakers.

When several people talk at once, the gain is shared among active mics. All mics sound

normal when used but there is no change in ambience, noise buildup, or feedback.

While people are talking, use the Yamaha mixer’s faders to set appropriate relative

levels for each mic channel. You can leave the faders up when the mics are not used

because the Dugan Speech System cues the mics up when needed.

Figure 1-1 shows four snapshots of the Dugan Speech System in action with three

mics.

Figure 1-1 Dugan Speech System

Sound

No one speaking Mic 2 speaking Mic 3 speaking Mics 2 and 3 speaking

at mics (dB)

Resulting

automix

gains (dB)

-30

-20

-10

1234

Dugan-MY16 User Guide Introduction

Frame 1: No one is speaking and the sound levels at all mics are low. The system fades

all channels to a medium gain that sums to one mic at full gain.

Frame 2: One person speaks alone. The system automatically fades their gain to full,

and turns the other two inputs down.

Frame 3: The first person finishes speaking and a second person begins. The system

automatically fades the new speaker’s input gain to full, and turns the other two down.

Frame 4: Two people speak simultaneously. The system automatically shares the

gain between them, and turns the other input down.

Remote Control and Software

Two Java applets are included on a thumb drive or CD, or can be downloaded from

our website:

• The Dugan Control Panel offers expanded operational capabilities (see Chapter 3:

The Dugan Control Panel).

• The Dugan Utility helps you connect to a network and update the firmware (see

Chapter 4: Updates).

The Dugan-MY16 can be controlled with:

• the Dugan Control Panel for Java (included);

• the Dugan Control Panel for iPad (sold separately)

• ASCII commands via Ethernet (contact Dan for information).

Subscribe to the duganusers Yahoo group to be notified when updates are available.

Dugan-MY16 User Guide

Chapter 2: Installation and Linking

This chapter explains how to:

• Install Dugan-MY16 card(s);

• Install the Dugan Control Panel for Dugan-MY16 cards and external Dugans;

• Link Dugan-MY16 cards and external Dugans into a single unified automatic mix-

ing controller.

Installing the Dugan-MY16 Card

Most Yamaha mixers have multiple slots, each of which has 16 channels. The Dugan-

MY16 can be installed in any available slot. The table below shows the current list of

Yamaha mixers that are compatible with the Dugan-MY16.

See YamahaProAudioSupport for the most up to date list.

To begin installing your Dugan-MY16, find your mixer model in the table below, and

set the Native

–Legacy switch accordingly. The Native–Legacy switch maintains Ya-

maha’s compatibility with its older mixers. Some older Yamaha mixers that require

the Legacy setting do not display the correct names for plug-in cards in their insert

patching screen.

* With LS9 firmware v1.21 or earlier, the LS9 insert patch points are pre-fader only. To properly mute

mixer channels, you must use the Dugan Control Panel for Java (included) or the Dugan Control Panel

for iPad (sold separately).

Yamaha Mixer Model Native-Legacy Switch

CL1 Native

CL3 Native

CL5 Native

PM5D/PM5D-RH Native

DSP5D Native

M7CL-48ES Legacy

M7CL-48 Legacy

M7CL-32 Legacy

MTX5-D Native

LS9-32* Legacy

LS9-16* Legacy

DM2000 Legacy

DM1000 Legacy

02R96 Legacy

01V96/01V96i Legacy

DME64N Native

DME24N Native

Dugan-MY16 User Guide

Choose an Operating Mode

The operating mode determines sample rate, linking, and channel count. Set the

Yamaha mixer’s sample rate before setting the operating mode (see your Yamaha

mixer’s user guide to learn how).

Choose one of the three operating modes:

Standard

Sixteen Dugan mixing channels at 44.1 or 48 kHz

ADAT I/O connectors can link multiple Dugan units

High-rate

Eight Dugan mixing channels at 88.2 or 96 kHz

ADAT I/O connectors can link multiple Dugan units

Shared

Eight Dugan mixing channels at 44.1 or 48 kHz

The ADAT I/O connectors serve as a general-purpose interface that is available

for patching on channels 9–16 of the Dugan-MY16’s slot. These channels are

unrelated to Dugan mixing and can be used as additional Yamaha mixer I/O.

To use channels 9–16 (as with any digital input), an appropriate synchroniza-

tion source must be selected (see your Yamaha mixer’s user guide).

Dugan-MY16 User Guide Installation and Linking

To configure and install the Dugan-MY16 card:

1. Set the 48 kHz–96 kHz sample rate switch according the table below.

The sample rate switch represents low (44.1 or 48 kHz) and high (88.2 or 96 kHz)

settings, respectively, that must correspond to your mixer’s current sample rate.

For example,

If your mixer is set to 44.1 kHz, use the 48 kHz position.

If your mixer is set to 88.2 kHz, use the 96 kHz position.

Figure 2-1 Circuit board and rear panel switches

2. Install the Dugan-MY16 card according to the instructions in your mixer’s user

guide.

3. Turn on the mixer.

If you are using Shared mode, an appropriate synchronization source must be

selected for channels 9–16. See your Yamaha mixer’s user guide for details.

4. Press and hold the RESET button for 3 seconds to restore the Dugan-MY16’s factory

default settings.

5. Set the rear panel LINK–AUDIO switch to the position corresponding to the selected

operating mode (see table above).

6. Set the NORM–SLAVE switch to NORM (up) for unlinked operation.

Mixer Sample

Rate

Sample Rate

Switch

LINK-AUDIO Switch

Standard

44.1 kHz 48 kHz LINK

48 kHz 48 kHz LINK

High Rate

88.2 kHz 96 kHz LINK

96 kHz 96 kHz LINK

Shared

44.1 kHz 48 kHz AUDIO

48 kHz 48 kHz AUDIO

Dugan-MY16 User Guide

7. Use your mixer’s channel select button to select the first mixer channel in which

to insert the Dugan-MY16.

Refer to your Yamaha mixer user guide to display the insert patching screen.

Legacy mixers will identify the card on the insert patching screen as either MY16AT

or MY8AE96.

8. Insert the Dugan-MY16 as a post-fader insert on this mic channel.

NOTE: LS9 mixers with firmware version 1.2 and older do not allow post-fader inserts. You must

either update the LS9’s firmware, use the Dugan Control Panel for Java (included), or the

Dugan Control Panel for iPad (sold separately).

9. Repeat steps 7 and 8 for each additional mixer mic channel in which you wish to

insert the Dugan-MY16.

No further configuration is required to operate the Dugan-MY16. We designed nom-

inal settings that work fine out of the box, which comes in handy if you are pressed

for time before an event. However, to take full advantage of the Dugan-MY16’s ad-

vanced features, we recommend installing the Dugan Control Panel software.

Connecting to a Computer or Network

To connect to a computer or network, attach a CAT5 cable to the rear panel

10/100BASE-T connector. Older PCs may require a crossover cable.

We strongly recommend that Windows users turn the Windows firewall off. The

Windows Firewall blocks port 9776 used by the Dugan software to communicate. If

you must leave the Windows firewall on, either open this port or use the workaround

described in Connecting when Windows Firewall is On on page 21.

We recommend turning off the computer’s WiFi during this process because it some-

times interferes. You can turn it back on after the connection has been established.

To set a specific IP address, proceed to Software Configuration for a Specific IP Address.

Two Java applets are provided with the Dugan-MY16:

• The Dugan Control Panel offers expanded operational capabilities.

• The Dugan Utility helps you connect to a network and update the firmware.

Insert the USB thumb drive or CD supplied with the Dugan-MY16, or download the

latest version from:

http://www.dandugan.com/downloads

- OR -

http://tech.groups.yahoo.com/group/duganusers/files/

Dugan-MY16 User Guide Installation and Linking

Establishing Network Connections

We recommend completing your network connection with a computer before using the

iPad app.

1. Launch Dugan-Utility-yyyymmdd.jar.

Figure 2-2 Dugan Utility

2. Wait a minute and if the list pane is blank, click Refresh List.

If the list pane remains blank, proceed to Manually Add Unit below.

If the list pane displays Dugan units, continue.

3. Click on the first unit in the list so it is highlighted.

The Network Parameters section displays information about that unit.

If Unit Reachable is YES, you are ready to use the Dugan Control Panel with that

unit. If you have additional Dugan units to connect, select the next unit in the list

and repeat this step. If you are finished with installation, proceed to Chapter 4:

Dugan Control Panel.

If Unit Reachable is NO, proceed.

iPad

Dugan-MY16 User Guide

4. Press and hold the rear panel NETWORK RESET button for 3 seconds.

This resets the following network parameters to their factory default value.

*xx = last two digits of serial number, unless 00, then use 100

5. Click Refresh List.

6. Click on the first unit in the list so it is highlighted.

If Unit Reachable is YES, you are ready to use the Dugan Control Panel with that

unit. If you have additional Dugan units to connect, select the next unit in the list

and repeat Step 3. If you are finished with installation, proceed to Chapter 4: Du-

gan Control Panel.

If Unit Reachable is NO, proceed to the next step.

7. Select the Use DHCP parameter.

8. Click Send New Params to Unit.

9. Highlight the unit in the list pane again.

If Unit Reachable is YES, this unit is ready to use with the Dugan Control Panel. If

you have additional Dugan units to connect, select the next unit in the list and

repeat Step 3. If you are finished with installation, proceed to Chapter 4: Dugan

Control Panel.

If Unit Reachable is NO, proceed to the next step.

10.Copy This Computer’s IP Address to the IP Address field, and increase the value in

the last (fourth) group by one.

For example, if This Computer’s IP Address is 192.168.1.101, set IP Address to

192.168.1.102.

11.Click Send New Params to Unit.

12.Highlight the unit in the list pane again.

If Unit Reachable is YES, this unit is ready to use with the Dugan Control Panel. If

you have additional Dugan units to connect, select the next unit in the list and

repeat Step 3. If you are finished with installation, proceed to Chapter 4: Dugan

Control Panel.

If Unit Reachable is NO, see Using the Internally Stored Dugan Control Panel on page 19.

IP Address

192.168.1.xx*

Netmask

255.255.255.0

Gateway

192.168.1.254

DHCP

off

Dugan-MY16 User Guide Installation and Linking

Manually Add Unit

If the Dugan unit does not appear in the Dugan Utility list pane, you can manually

add the unit:

1. Hold down NETWORK RESET for three seconds.

This performs a network reset.

2. Click Manually Add Unit.

3. Enter the default IP address: 192.168.1.xx

xx = last two digits of serial number, unless they are 00, in which case enter 100.

4. Click OK to exit the dialog.

5. Click Refresh List.

If the list pane is still blank, see Using the Internally Stored Dugan Control Panel below.

Using the Internally Stored Dugan Control Panel

Normally, the Dugan Control Panel is run from the Dugan-Control-Panel-vxxx.jar

file. However, if for any reason you do not have that file or an Internet connection,

you can run the Dugan Control Panel from a copy stored in the unit (see Chapter 4:

Updates).

It is not currently possible to run the internally stored Dugan Control Panel from an iPad.

To run the internally stored Dugan Control Panel:

1. Launch your browser.

2. Enter the IP Address of the unit.

3. If you do not know its IP Address, press and hold the rear panel NETWORK RESET

button for 3 seconds.

The IP Address is set to 192.168.1.xx (xx = last two digits of the unit’s serial num-

ber, unless 00, then use 100).

4. Since the Top Pane will be empty, open a separate browser tab for each unit you

wish to operate, and enter its IP Address.

If this does not work, consult the duganusers Yahoo group (http://tech.groups.ya-

hoo.com/group/duganusers

) or contact Dan.

iPad

Dugan-MY16 User Guide

Software Configuration for a Specific IP Address

This section explains to users with IT expertise how to set a specific IP address for any

Dugan unit on the network.

1. Launch Dugan-Utility-vxx.jar.

Figure 2-3 Dugan Utility

2. Wait a minute and if the list pane is blank, click Refresh List.

If the list pane remains blank, skip back to Manually Add Unit above.

If the list pane displays Dugan units, continue.

3. Click on the first unit in the list so it is highlighted.

The Network Parameters section displays information about that unit.

4. If Use DHCP is selected, de-select it.

5. Enter the desired IP address into the IP Address field.

6. Click Send New Params to Unit.

The

Dugan-MY16 will reboot.

La pagina sta caricando ...

Yamaha MY16 Manuale utente

Marca: Yamaha

Modello: MY16

Categoria: Mixer audio

Tipo: Manuale utente

Questo manuale è adatto anche per

DUGAN-MY16

Scarica il pdf

rapporto

in altre lingue

English: Yamaha MY16 User manual
français: Yamaha MY16 Manuel utilisateur
español: Yamaha MY16 Manual de usuario
Deutsch: Yamaha MY16 Benutzerhandbuch
русский: Yamaha MY16 Руководство пользователя
Nederlands: Yamaha MY16 Handleiding
português: Yamaha MY16 Manual do usuário
dansk: Yamaha MY16 Brugermanual
polski: Yamaha MY16 Instrukcja obsługi
svenska: Yamaha MY16 Användarmanual
Türkçe: Yamaha MY16 Kullanım kılavuzu
suomi: Yamaha MY16 Ohjekirja
română: Yamaha MY16 Manual de utilizare

Documenti correlati

Altri documenti

Denon Heos Extend Manuale del proprietario