ProLights 60 W moving spot Manuale utente

USER MANUAL

MANUALE UTENTE

PIXIESPOT

SPOT MOVING HEAD

EN - IT

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the

characteristics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

REV.003-06/17

1

PIXIESPOT

TABLE OF CONTENTS

Safety

General instructions

Warnings and installation precautions

1 Introduction

1. 1 Description

1. 2 Technical specications

1. 3 Operating elements and connections

2 Installation

2. 1 Mounting

3 Functions and settings

3. 1 Operation

3. 2 Basic

3. 3 Menu structure

3. 4 DMX addressing

3. 5 Connection of the DMX line

3. 6 Construction of the DMX termination

3. 7 DMX channels

3. 8 DMX conguration

3. 9 Autoshow

3. 10 Focus adjustment

3. 11 Motor settings

3. 12 Fixture settings

3. 13 Display settings

3. 14 Fixture test

3. 15 Reset functions

3. 16 Fixture informations

4 Maintenance

4. 1 Maintenance and cleaning the unit

4. 2 Fuse replacement

4. 3 Trouble shooting

2

4

6

7

8

9

12

13

14

17

18

19

20

21

• PIXIESPOT

• Mount bracket

• Power supply cable and signal cable

• Safety rope

• User manual

Packing content

PIXIESPOT

2

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

SAFETY

General instruction

• The products referred to in this manual conform to the European Community Directives and are there-

fore marked with .

• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.

Never make any modications on the unit not described in this instruction manual, otherwise you will

risk an electric shock.

• Connection must be made to a power supply system tted with ecient earthing (Class I appliance ac-

cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units

from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• The connection to the main network of electric distribution must be carried out by a qualied electrical

installer. Check that the main frequency and voltage correspond to those for which the unit is designed

as given on the electrical data label.

• This unit is not for home use, only professional applications.

• Never use the xture under the following conditions:

- in places wet;

- in places subject to vibrations or bumps;

- in places with an ambient temperature of over 45°C.

• Make certain that no inammable liquids, water or metal objects enter the xture.

• Do not dismantle or modify the xture.

• All work must always be carried out by qualied technical personnel. Contact the nearest sales point for

an inspection or contact the manufacturer directly.

• If the unit is to be put out of operation denitively, take it to a local recycling

plant for a disposal which is not harmful to the environment.

Warnings and installation precautions

• If this device will be operated in any way dierent to the one described in this manual, it may suer

damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like

short circuit, burns, electric shock, etc.

• Before starting any maintenance work or cleaning the projector, cut o power from the main supply.

• Always additionally secure the projector with the safety rope. When carrying out any work, always com-

ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country

in which the xture’s being used.

• For inside use only. Not designed for outside use.

• The minimum distance between the xture and surrounding walls must be more than 50 cm and the

air vents at the housing must not be covered in any case.

• Install the xture in a well ventilated place.

• Keep any inammable material at a safe distance from the xture.

• The maximum temperature that can be reached on the external surface of the tting, in a thermally

steady state, is high. After power o, please cool down over 15 minutes.

• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent

that their eectiveness is impaired.

• The lamp (LED) shall be changed if it has become damaged or thermally deformed.

• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ashing light, may

trigger epileptic seizures in photosensitive persons or persons with epilepsy.

3

PIXIESPOT

- 1 - INTRODUCTION

1.1 DESCRIPTION

PIXIESPOT was the rst TRIBE spot moving head to deliver a full spectrum chromatic synthesis, equipped

with a 60W RGBW/FC LED light source to perform limitlessbrightness, intense and saturated colours as

well as proper whites.PIXIESPOT can be also controlled wireless through the optional USB WIFI transceiver

in combination with WIFIBOX and the SmartColor app.

1.2 TECHNICAL SPECIFICATIONS

LIGHT SOURCE

• Source: 60W RGBW Osram LED

• Luminous ux: 1069lm

• Lux: 1682lux @3m full

• Source life expectancy: >50.000 h

OPTICS

• Beam angle: 18°

• Lens type: high-quality glass lens optics

• Focus: motorised

COLOUR SYSTEM

• Colour mixing: RGBW/FC

• CTC: linear CTO correction 2700~6000K

• Colour wheel: virtual colour wheel with presets

DYNAMIC EFFECTS

• Rotating gobos: 7 rotating gobos + open, interchangeable

• Gobo size: gobo Ø 16,9 mm - img Ø 14 mm - 2 mm

• Circular prism: 3f with bi-directional rotation

• Auto mode: built-in programs with execution speed adjustment

• Sound mode: music activation through internal microphone and sensitivity control

BODY

• Pan angle: 540°

• Tilt angle: 270°

• Pan/Tilt resolution: 8/16 bit

• Body: aluminium structure with hi-resistance polycarbonate cover

• Body colour: black, white nishing available

CONTROL

• Protocols: DMX512

• DMX channels: 15 / 18 / 23channel

• Display: black OLED high resolution display

• Firmware upgrade: yes, via USB-DMX interface (UPBOX1) not included

• Master/Slave: for synchronized operation of more units linked in a chain

ELECTRONICS

• Dimmer: linear 0~100% electronic dimmer

• Dimmer curves: dierent dimming curves available

• Strobe / shutter: 1/28 Hz, electronic

• Operating temperature: -10° ~ +45°

• Flicker: icker free operation

PIXIESPOT

4

ELECTRICAL

• Power supply: 100-240V – 50/60Hz

• Power consumption (at 230V): 118W

• Power consumption (at 120V): 120,3W

• Output (at 230V): 17 units on a single power line

• Output (at 120V): 9

PHYSICAL

• Cooling: forced air with low noise fan

• Sospension and xing: any position with quick-lock omega brackets

• Data: USB port for USB WIFI transmitter (optional)

• Signal connection: XLR 3p IN/OUT connectors

• Power connection: IEC IN/OUT connectors

• IP rating: 20

• Dimensions (WxHxD): 253x352x192mm

• Weight: 7kg

Technical drawing Fig.1

352

253

192

5

PIXIESPOT

1. MOVING HEAD

2. REVOLVING ARM

3. HANDLE

4. LED INDICATOR "POWER"

5. LED INDICATOR "DMX"

6. CONTROL PANEL with OLED

display and 5 button used to

access the control panel functions

and manage them.

7. POWER IN mains plug for

connection to a socket

(100-240V~/50-60Hz) via the

supplied mains cable. The support

for the mains fuse is located near

the mains plug. Only replace a

blown fuse by one of the same

type.

8. POWER OUT: connect to supply

power to the

9. DMX IN (3 poles XLR ):

1 = mass, 2 = DMX -, 3 = DMX +

10. DMX OUT (3 poles XLR):

1= mass, 2 = DMX -, 3 = DMX +

11. Universal Serial Bus (USB)

1.3 OPERATING ELEMENTS AND CONNECTIONS

Fig.2

View A

View B

spot

4

7

9

11

10

8

6

A

2

1

B

5

3

Power

DMX

Enter

PIXIESPOT

6

- 2 - INSTALLATION

2.1 MOUNTING

The PIXIESPOT may be set up on a solid and even surface. By means of the xing facilities of the baseplate,

the unit can also be mounted upside down to a cross arm. The base plate is shown in g.3. For xing, stable

mounting clips are required. According to the gure, the bolts of the brackets are placed into the openings

provided in the base plate and turned clockwise until they lock (to the stop). Always ensure that the unit

is rmly xed to avoid vibration and slipping while operating. The mounting place must be of sucient

stability and be able to support a weight of 10 times of the unit’s weight. When carrying out any installa-

tion, always comply scrupulously with all the regulations (particularly regarding safety) currently in force

in the country in which the xture’s being used. Always additionally secure the projector with the safety

rope from falling down. For this purpose, fasten the safety rope at a suitable position so that the maximum

fall of the projector will be 20 cm.

CLAMP

SAFETY

CABLE

OMEGA

BRACKETS

Fig.3

7

PIXIESPOT

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

Connect the supplied main cable to a socket (100-240V~/50-60Hz). The unit will run built-in program to

reset all motors to their home position. Shortly after that the PIXIESPOT is ready for operation. To switch

o, disconnect the mains plug from the socket. For a more convenient operation it is recommended to

connect the unit to a socket which can be switched on and o via light switch.

3.2 BASIC

The PIXIESPOT has a OLED display and 5 button used to access the control panel functions and manage

them (g.4).

Fig.4 - Functions of the buttons and display icons

UP DOWN LEFT RIGHT ENTER

Increases the value

displayed or passes to

the previous item in a

menu

Decreases the value

displayed or passes to

the next item in the

menu

To enter in the main

menù or to return to the

top level

Commute from units,

tens, hundred in the

menu

Conrms the displayed

value, or activates the

displayed function, or

enters the successive

menu

Enter

PIXIESPOT

8

3.3 MENU STRUCTURE

MENU

1 DMX Functions

ð

DMX Address

ð

Value (1-512)

DMX Channels

ð

15 CH

18 CH

23 CH

2 Show setup

ð

Show Mode

ð

Show 1

Show 2

Show 3

Show 4

Focus Adjust

ð

000 - 255

3 Motor Setup

ð

Pan Inverse

ð

No

Yes

Tilt Inverse

ð

No

Yes

Motor Oset

ð

Pan Oset

ð

000 - 255

Tilt Oset

ð

000 - 255

Gobo Oset

ð

000 - 255

Prism Oset

ð

000 - 255

Focus Oset

ð

000 - 255

4 System Setup Master/Slave

ð

Master

Slave

Sound Sence

ð

000 - 100

White Balance

ð

Red

ð

125 - 255

Green

ð

125 - 255

Blue

ð

125 - 255

Dimmer Mode

ð

O

Dimmer 1

Dimmer 2

Dimmer 3

Fan Mode

ð

Auto Speed

High Speed

Factory Setting

ð

No

Yes

5 Display Setup

ð

Display Inverse

ð

No

Yes

9

PIXIESPOT

Back Light

ð

On

10s

20s

30s

Warn Cue

ð

O

On

6 Test Setup

ð

Auto Test

ð

Manual Test

ð

Pan

ð

000 - 255

Pan Fine

ð

000 - 255

Tilt

ð

000 - 255

Tilt Fine

ð

000 - 255

Pan/Tilt Speed

ð

000 - 255

Dimmer

ð

000 - 255

Shutter

ð

000 - 255

Red

ð

000 - 255

Green

ð

000 - 255

Blue

ð

000 - 255

White

ð

000 - 255

Gobo

ð

000 - 255

RGobo

ð

000 - 255

Prism

ð

000 - 255

RPrism

ð

000 - 255

Focus

ð

000 - 255

7 Reset Setup

ð

Auto reset

Manual Reset

ð

Pan Reset

ð

No

Yes

Tilt Reset

ð

No

Yes

Gobo Reset

ð

No

Yes

Prism Reset

ð

No

Yes

Focus Reset

ð

No

Yes

PIXIESPOT

10

8 Information

ð

Fixture Time

ð

0 - 9999

Software Version

ð

DISP V 1.0

CTR - XY V 1.0

CTR - LED V 1.0

LED Temperature

ð

58°C

11

PIXIESPOT

Several units may be interconnected; follow the instructions below:

1. Connect the DMX OUT of the master unit via 3-pole XLR cable to the DMX IN of the rst slave unit.

2. Connect the DMX OUT of the rst slave unit to the DMX IN of the second slave unit, etc. until all units

are connected in a chain.

Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of the

units. For longer cable runs we suggest a terminator at the last xture (see page 13).

3.4 DMX ADDRESSING

To set DMX addressing follow the instructions below:

• Press the button LEFT to enter the menu mode.

• Use the buttons UP/DOWN to select the DMX Functions item. Press the button ENTER to conrm.

• Press the buttons UP/DOWN to select the DMX Address item. Then press the button ENTER to conrm.

• Press the buttons UP/DOWN to select the desired value 001-512; Then press the button ENTER to con-

rm.

• Press repeatedly the button LEFT to return the menu mode.

To able to operate the PIXIESPOT with a light controller, adjust the DMX start address for the rst a

DMX channel. If e. g. address 33 on the controller is provided for controlling the function of the rst DMX

channel, adjust the start address 33 on the PIXIESPOT. The other functions of the light eect panel are then

automatically assigned to the following addresses.

Fig.5 - Example 15 DMX channels conguration

. . . . . . . . . . . .

DMX512 Controller

DMX Address: 78DMX Address: 48DMX Address: 33 DMX Address: 63

Number of

DMX channels

Start address

(example)

DMX Address

occupied

Next possible start

address for unit No. 1

Next possible start

address for unit No. 2

Next possible start

address for unit No. 3

15 33 33-47 48 63 78

18 33 33-50 51 69 87

23 33 33-55 56 79 102

PIXIESPOT

12

Fig.6

Fig.7

3.5 CONNECTION OF THE DMX LINE

DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120Ω imped-

ance and low capacity.

The following diagram shows the connection mode:

ATTENTION

The screened parts of the cable (sleeve) must never be connected to the system’s earth, as this would

cause faulty xture and controller operation.

Over long runs can be necessary to insert a DMX level matching amplier.

For those connections the use of balanced microphone cable is not recommended because it cannot

transmit control DMX data reliably.

• Connect the controller DMX input to the DMX output of the rst unit.

• Connect the DMX output to the DMX input of the following unit. Connect again the output to the input

of the following unit until all the units are connected in chain.

• When the signal cable has to run longer distance is recommended to insert a DMX termination on the

last unit.

3.6 CONSTRUCTION OF THE DMX TERMINATION

The termination avoids the risk of DMX 512 signals being reected back along the cable when they reach-

es the end of the line: under certain conditions and with certain cable lengths, this could cause them to

cancel the original signals.

The termination is prepared by soldering a 120Ω 1/4 W resistor between pins 2 and 3 of the 3-pin male XLR

connector, as shown in gure.

DMX - OUTPUT

XLR socket

DMX - INPUT

XLR plug

Pin1 : GND - Shield

Pin2 : - Negative

Pin3 : + Positive

Example:

3 pin XLR connector

13

PIXIESPOT

3.7 DMX CHANNELS

MODE MODE MODE

FUNCTION DMX

Value

15 Ch 18 Ch 23 Ch

1 1 1

PAN

0~100% 000 - 255

2 2 2

PAN FINE

0~100% 000 - 255

3 3 3

TILT

0~100% 000 - 255

4 4 4

TILT FINE

0~100% 000 - 255

5 5 5

PAN/TILT SPEED

Fast to slow 000 - 255

6 6 6

SPECIAL FUNCTION

No function

Reset all (Hold 3 Seconds)

No function

000 - 199

200 - 209

210 - 255

7 7 7

RED

0~100% 000 - 255

8 8 8

GREEN

0~100% 000 - 255

9 9 9

BLUE

0~100% 000 - 255

10 10 10

WHITE

0~100% 000 - 255

11 11

COLOR

No function

Red

Yellow

Green

Cyan

Blue

Magenta

White

Full

Clockwise rotation (Fast to Slow)

Stop Run

Counterclockwise rotation (Slow to Fast)

000 - 007

008 - 022

023 - 037

038 - 052

053 - 067

068 - 082

083 - 097

098 - 112

113 - 127

128 - 189

190 - 193

194 - 255

11 12 12

GOBO

Open

Gobo 1

Gobo 2

Gobo 3

Gobo 4

000 - 007

008 - 015

016 - 023

024 - 031

032 - 039

PIXIESPOT

14

MODE MODE MODE

FUNCTION DMX

Value

15 Ch 18 Ch 23 Ch

12 12

Gobo 5

Gobo 6

Gobo 7

Gobo 1 Shaking

Gobo 2 Shaking

Gobo 3 Shaking

Gobo 4 Shaking

Gobo 5 Shaking

Gobo 6 Shaking

Gobo 7 Shaking

Clockwise rotation (Fast to Slow)

Stop Rotation

Counterclockwise rotation (Slow to Fast)

040 - 047

048 - 055

056 - 063

064 - 073

074 - 082

083 - 091

092 - 100

101 - 109

110 - 118

119 - 127

128 - 189

190 - 193

194 - 255

12 13 13

GOBO ROTATION

Stop Rotation

Clockwise rotation (Fast to Slow)

Stop Rotation

Counterclockwise rotation (Slow to Fast)

000 - 127

128 - 129

190 - 193

194 - 255

13 14 14

PRISM

Prism O

Prism On

Clockwise rotation (Fast to Slow)

Stop Rotation

Counterclockwise rotation (Slow to Fast)

000 - 010

011 - 127

128 - 189

190 - 193

194 - 255

14 15 15

STROBE

Shutter Closed

No Function (Shutter open)

Strobe Eect (Slow to Fast)

No function (Shutter open)

Pulse-eect in sequence

No function (Shutter open)

Random Strobe Eect (Slow to Fast)

No Function (Shutter open)

000 - 031

032 - 063

064 - 095

096 - 127

128 - 159

160 - 191

192 - 223

224 - 255

15 16 16

FOCUS

0~100% 000 - 255

17 17

DIMMER

0~100% 000 - 255

18

COLOR MACRO

No Function

R:100% / G:0~100% / B:0 / W:0

R:100%~0 / G:100% / B:0 / W:0

R:0 / G:100% / B:0~100% / W:0

R:0 / G:100%~0 / B:100% / W:0

000 - 010

011 - 030

031 - 050

051 - 070

071 - 090

15

PIXIESPOT

MODE MODE MODE

FUNCTION DMX

Value

15 Ch 18 Ch 23 Ch

18

R:0~100% / G:0 / B:100% / W:0

R:100% / G:0 / B:100%~0 / W:0

R:100% / G:0~100% / B:0~100% / W:0

R:100%~0 / G:100%~0 / B:100% / W:0

R:100% / G:100% / B:100% / W:100%

Color 1

Color 2

Color 3

Color 4

Color 5

Color 6

Color 7

Color 8

Color 9

Color 10

Color 11

091 - 110

111 - 130

131 - 150

151 - 170

171 - 200

201 - 205

206 - 210

211 - 215

216 - 220

221 - 225

226 - 230

231 - 235

236 - 240

241 - 245

246 - 250

251 - 255

19

AUTO PROGRAM

No Function

4 Colours Snap

4 Colours Fade

15 Colours Snap

15 Colours Fade

Sound Control

000 - 010

011 - 070

071 - 130

131 - 190

191 - 250

251 - 255

20

AUTO PROGRAM SPEED

Speed (Slow to Fast)

SOUND SENSITIVITY

Sound Sensitivity OFF

Control the Sound Sensitivity

000 - 010

011 - 255

21

MOTOR SHOW

No Function

Motor Show 1

Motor Show 2

Motor Show 3

Motor Show 4

Motor Show 5 (Motor Show 1 - 4)

Motor Show 6

000 - 010

011 - 058

059 - 106

107 - 154

155 - 202

203 - 250

251 - 255

22

MOTOR SHOW SPEED

Speed (Slow to Fast) 000 - 255

18 23

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode 1

Dimmer speed mode 2

Dimmer speed mode 3

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

PIXIESPOT

16

3.8 DMX CONFIGURATION

The PIXIESPOT has 3 DMX channels congurations selectable through the control panel.

• Press the button LEFT to enter the menu mode.

• Use the buttons UP/DOWN to select the DMX Functions item. Press the button ENTER to conrm.

• Press the buttons UP/DOWN to select the DMX Channels item. Then press the button ENTER to conrm.

• Press the buttons UP/DOWN to select the desired conguration 15CH - 18CH - 23CH. ; Then press the button

ENTER to save.

• Press repeatedly the button LEFT to return the menu mode.

The tables on page 14 indicate the operating mode and DMX value. The PIXIESPOT is equipped with

3-pole XLR connections.

3.9 AUTOSHOW

To enter in the automatic mode and allow to the unit to carry out its show program independently follow

the instructions below:

• Press the button LEFT to enter the menu mode.

• Use the buttons UP/DOWN to select the Show setup item. Press the button ENTER.

• Press the buttons UP/DOWN to select the Show Mode item. Then press the button ENTER to conrm.

• Press the buttons UP/DOWN to select the desired program Show1 - Show2 - Show3-Show4 ; Then press the

button ENTER to save.

• Press repeatedly the button LEFT to return the menu mode.

3.10 FOCUS ADJUSTMENT

To set the focus regulation follow the instructions below:

• Press the button LEFT to enter the menu mode.

• Use the buttons UP/DOWN to select the Show setup item. Press the button ENTER.

• Press the buttons UP/DOWN to select the Focus adjust item. Then press the button ENTER to conrm.

• Press the buttons UP/DOWN to select the desired values (000-255); Then press the button ENTER to save.

• Press repeatedly the button LEFT to return the menu mode.

3.11 MOTOR SETTINGS

To change the unit parameters follow the instructions below:

• Press the button LEFT to enter the menu mode.

• Use the buttons UP/DOWN to select the Motor Setup item. Press the button ENTER.

• Press the buttons UP/DOWN to select the desired option item and press the button ENTER to conrm:

- Pan Inverse - Used for reversing Pan movement. Select Pan Inverse, press ENTER button to conrm,

present mode will blink on the display, use UP/DOWN button to select No (normal) or Yes (pan

inverse), press ENTER button to store.

- Tilt Inverse - Used for reversing tilt movement. Select Tilt Inverse, press ENTER button to conrm, present

mode will blink on the display, use UP/DOWN button to select No (normal) or Yes (tilt inverse), press

ENTER button to store.

• Motor Oset - Allows you to set an oset for the pan/tilt motor. After selecting Motor Setup function press

button ENTER to conrm. Use the buttons UP/DOWN to select Pan Oset - Tilt Oset - Gobo Oset - Prism Oset

- Focus Oset and press the button ENTER. Set through the directional buttons the desired value (000-255).

Then press the button ENTER.

• Press repeatedly the button LEFT to return the menu mode.

17

PIXIESPOT

3.12 FIXTURE SETTINGS

You can change the parameters for the device by following these steps:

• Press the button LEFT to enter the menu mode.

• Use the buttons UP/DOWN to select the System setup item. Press the button ENTER to conrm.

• Press the buttons UP/DOWN to select the desired option item and press the button ENTER to conrm:

- Master/Slave - This conguration allows to connect many units PIXIESPOT. The rst will be set as Master

and the others will work as Slave with the same eect. Press the buttons UP/DOWN to set the units as

master or slave. Press the button ENTER to conrm. Use PIXIESPOT DMX connectors and XLR cable

to do a units chain.

- Sound Sence - Microphone sensibility for the control through musical command in autoshow modal-

ity. After selecting Sound Sence function press the button ENTER to conrm. Use the buttons UP/

DOWN to select the desired value (000-100). Then press the button ENTER.

NOTE - In music mode, via its integrated microphone, the unit can be controlled by music with a

clear rhythm in the bass range. If the music control should not work optimally, increase the volume

or reduce the distance between the sound source and the light eect unit or alternatively increase

the sensitivity of the microphone.

- White Balance - White Balance function. Select the White Balance function to set the white balance by

changing the values (125-255) of the colors Red, Green and Blue.

- Dimmer Mode - Adjusting the dimmer. Enter in Dimmer Mode to select specic dimming curve.

Particularly when set:

• O: The increase in light intensity is linear

• Dimmer 1: Light intensity control is nger at low levels and coarse at high levels.

• Dimmer 2: Light intensity control is nger at high levels and coarse at low levels.

• Dimmer 3: Light intensity control is nger at low levels and high levels and coarse at medium levels.

- Fan Mode - Fan speed. Select the desired fan speed High Speed or Auto Speed through the button UP/

DOWN.

- Factory Settings - Factory reset. Select Factory Settings function and then Yes to restore all values to the

original factory settings.

• Press repeatedly the button LEFT to return the menu mode.

3.13 DISPLAY SETTINGS

• Press the button LEFT to enter the menu mode.

• Press the buttons UP/DOWN to select the Display setup item. Then press the button ENTER.

• Press the buttons UP/DOWN to select the desired option item and press the button ENTER to conrm:

- Display Inverse - Used for reversing display. Select Display Inverse, press ENTER button to conrm, present

mode will blink on the display, use UP/DOWN button to select No (normal display) or Yes (inverse dis-

play), press ENTER button to store.

- Back Light - Display backlight. Select Back Light, press ENTER button to conrm. Use the UP/DOWN keys

to select On for display always on or Off for setting display o one minute after the exit from the menu.

- Warn Cue - Select Warn Cue, press ENTER button to conrm, present mode will blink on the display, use

UP/DOWN button to select No (Normal) or Yes (display will show the error warning when the unit

went wrong).

• Press repeatedly the button LEFT to return the menu mode.

3.14 FIXTURE TEST

Auto Test

Allow checking the proper functioning of the unit. Start the automatic test in the following way:

PIXIESPOT

18

• Press the button LEFT to enter the menu mode.

• Use the buttons UP/DOWN to select the Test Setup item. Press the button ENTER to conrm.

• Press the buttons UP/DOWN to select the Auto Test item.

• To conrm and start the automatic test press the ENTER button.

Manual Test

It allows to do adjustments on the eects through comands pannel to obtain a perfect balance between

the projectors.

• Press the button LEFT to enter the menu mode.

• Press the buttons UP/DOWN to select the item Test Setup. Then press the button ENTER.

• Press the buttons UP/DOWN to select the Manual Test item. Then press the button ENTER.

• Select the eect you want change (Pan, Pan Fine, Tilt, Tilt Fine, P/T Speed, Dimmer, Shutter, Red, Green, Blue, White,

Gobo, RGobo, Prism, Rprism, Focus).Then press the button ENTER to conrm

• Use the directional buttons to calibrate the eect setting a value between 0 - 255. Then press the but-

ton ENTER to conrm

• Press repeatedly the button LEFT to return the menu mode.

3.15 RESET FUNCTIONS

Auto reset

• Press the button LEFT to enter the menu mode.

• Press the buttons UP/DOWN to select the item Reset Setup. Then press the button ENTER.

• Press the buttons UP/DOWN to select the item Auto reset. Then press the button ENTER to conrm and

to restart automatically

Manual reset

• Press the button LEFT to enter the menu mode.

• Press the buttons UP/DOWN to select the item Reset Setup. Then press the button ENTER.

• Press the buttons UP/DOWN to select the item Manual reset. Then press the button ENTER to conrm.

• Press the buttons UP/DOWN to select the function you want reset between Pan, Tilt, Gobo, Prism e Focus. In

this way selecting Yes it is possible to start a preset program to restore the selected function.

• Then press the button ENTER to conrm, waiting the reactivation of the function.

3.16 FIXTURE INFORMATION

• Press the button LEFT to enter the menu mode.

• Press the buttons UP/DOWN to select the item Information. Then press the button ENTER.

• Press the buttons UP/DOWN to select the desired option item and press the button ENTER to conrm:

- Fixture Time - Through the Fixture Time function you can display the operating time of the projector.

- Software Version - Select Software Version, press ENTER button to conrm, rmware version will show on

the display.

- Temperature - Through the function Temperature can be displayed on the display the temperature of

the device in ° C.

• Press repeatedly the button LEFT to return the menu mode.

La pagina sta caricando ...

ProLights 60 W moving spot Manuale utente

ProLights 60 W moving spot Manuale utente

in altre lingue

Documenti correlati

Altri documenti