Indesit IWC 6105 (EU) Guida utente

Categoria
Lavatrici
Tipo
Guida utente
1
GB
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Description of the washing machine
and starting a wash cycle, 4-5
Control panel
Indicator lights
Starting a wash cycle
Wash cycles, 6
Table of wash cycles
Personalisation, 7
Setting the temperature
Setting the spin speed
Functions
Detergents and laundry, 8
Detergent dispenser drawer
Bleach cycle
Preparing the laundry
Garments requiring special care
Load balancing system
Precautions and tips, 9
General safety
Disposal
Care and maintenance, 10
Cutting off the water or electricity supply
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Troubleshooting, 11
Service, 12
IWC 6105
Instructions for use
WASHING MACHINE
English,1
GB
Espańol,13
ES
Polski,25
PL
Portuguęs,37
PT
Italiano,49
IT
2
GB
Installation
! This instruction manual should be kept in a safe place for
future reference. If the washing machine is sold, transferred
or moved, make sure that the instruction manual remains
with the machine so that the new owner is able to familiari-
se himself/herself with its operation and features.
! Read these instructions carefully: they contain vital infor-
mation relating to the safe installation and operation of the
appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its packaging.
2. Make sure that the washing machine has not been
damaged during the transportation process. If it has been
damaged, contact the retailer and do not proceed any
further with the installation process.
3. Remove the 4 protective
screws (used during tran-
sportation) and the rubber
washer with the correspon-
ding spacer, located on the
rear part of the appliance
(see figure).
4. Close off the holes using the plastic plugs provided.
5. Keep all the parts in a safe place: you will need them
again if the washing machine needs to be moved to ano-
ther location.
! Packaging materials should not be used as toys for
children.
Levelling
1. Install the washing machine on a flat sturdy floor, without
resting it up against walls, furniture cabinets or anything
else.
2. If the floor is not perfectly
level, compensate for any
unevenness by tightening
or loosening the adjusta-
ble front feet (see figure);
the angle of inclination,
measured in relation to the
worktop, must not exceed
2°.
Levelling the machine correctly will provide it with stability,
help to avoid vibrations and excessive noise and prevent it
from shifting while it is operating. If it is placed on carpet or
a rug, adjust the feet in such a way as to allow a sufficient
ventilation space underneath the washing machine.
Connecting the electricity and water
supplies
Connecting the water inlet hose
1. Connect the supply pipe
by screwing it to a cold
water tap using a ¾ gas
threaded connection (see
figure).
Before performing the con-
nection, allow the water to
run freely until it is perfectly
clear.
2. Connect the inlet hose
to the washing machine by
screwing it onto the corre-
sponding water inlet of the
appliance, which is situa-
ted on the top right-hand
side of the rear part of the
appliance (see figure).
3. Make sure that the hose is not folded over or bent.
! The water pressure at the tap must fall within the values
indicated in the Technical details table (see next page).
! If the inlet hose is not long enough, contact a specialised
shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
3
GB
65 - 100 cm
Connecting the drain hose
Connect the drain hose,
without bending it, to a drai-
nage duct or a wall drain
located at a height between
65 and 100 cm from the
floor;
alternatively, rest it on
the side of a washbasin
or bathtub, fastening the
duct supplied to the tap
(see figure). The free end
of the hose should not be
underwater.
! We advise against the use of hose extensions; if it is
absolutely necessary, the extension must have the same
diameter as the original hose and must not exceed 150 cm
in length.
Electrical connections
Before plugging the appliance into the electricity socket,
make sure that:
the socket is earthed and complies with all applicable
laws;
the socket is able to withstand the maximum power load
of the appliance as indicated in the Technical data table
(see opposite);
the power supply voltage falls within the values indicated
in the Technical data table (see opposite);
the socket is compatible with the plug of the washing
machine. If this is not the case, replace the socket or the
plug.
! The washing machine must not be installed outdoors,
even in covered areas. It is extremely dangerous to leave
the appliance exposed to rain, storms and other weather
conditions.
! When the washing machine has been installed, the elec-
tricity socket must be within easy reach.
! Do not use extension cords or multiple sockets.
! The cable should not be bent or compressed.
! The power supply cable must only be replaced by autho-
rised technicians.
Warning! The company shall not be held responsible in the
event that these regulations are not respected.
The first wash cycle
Once the appliance has been installed, and before you use
it for the first time, run a wash cycle with detergent and no
laundry, using the wash cycle 2.
Technical data
Model
IWC 6105
Dimensions
width 59.5 cm
height 85 cm
depth 53,5 cm
Capacity
from 1 to 6 kg
Electrical
connections
please refer to the technical data plate
fixed to the machine
Water connection
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 52 litres
Spin speed
up to 1000 rotations per minute
Test
Programmes
according to
2010/1061
Programme 2: temperature 60°C and
40°C
This appliance conforms to the following
EC Directives:
- 2004/108/EC (Electromagnetic Compa-
tibility)
- 2002/96/EC
- 2006/95/EC (Low Voltage)
4
GB
Detergent dispenser drawer: used to dispense deter-
gents and washing additives (see “Detergents and laundry”).
ON/OFF button: switches the washing machine on and off.
WASH CYCLE knob: programmes the wash cycles. During
the wash cycle, the knob does not move.
FUNCTION buttons with indicator light: used to select the
available functions. The indicator light corresponding to the
selected function will remain lit.
TEMPERATURE knob: sets the temperature or the cold
wash cycle (see “Personalisation”).
SPIN SPEED knob: sets the spin speed or exclude the spin
cycle completely (see “Personalisation”).
WASH CYCLE PROGRESS/DELAY TIMER
indicator
light
s: used to monitor the progress of the wash cycle.
The illuminated indicator light shows which phase is in pro-
gress.
If the Delay Timer function has been set, the time remaining
until the wash cycle starts will be indicated (see next page).
DOOR LOCKED indicator light: indicates whether the door
may be opened or not (see next page).
START/PAUSE button with indicator light: starts or tempo-
rarily interrupts the wash cycles.
N.B. To pause the wash cycle in progress, press this button;
the corresponding indicator light will flash orange, while the
indicator light for the current wash cycle phase will remain lit
in a fixed manner. If the DOOR LOCKED indicator light is
switched off, the door may be opened.
To start the wash cycle from the point at which it was inter-
rupted, press this button again.
Standby mode
This washing machine, in compliance with new energy sa-
ving regulations, is fitted with an automatic standby system
which is enabled after about 30 minutes if no activity is
detected. Press the ON-OFF button briefly and wait for the
machine to start up again.
Description of the washing
machine and starting a wash cycle
WASH CYCLE PROGRESS/
DELAY TIMER indicator lights
DOOR LOCKED
indicator light
START/
PAUSE
button with
indicator light
Control panel
Detergent dispenser drawer
ON/OFF
button
WASH CYCLE
knob
TEMPERATURE
knob
FUNCTION
buttons with
indicator lights
SPIN SPEED
knob
5
GB
Indicator lights
The indicator lights provide important information.
This is what they can tell you:
Delayed start
If the DELAY TIMER function has been activated (see “Per-
sonalisation”), after the wash cycle has been started the
indicator light corresponding to the selected delay period
will begin to flash:
As time passes, the remaining delay will be displayed and
the corresponding indicator light will flash:
The set programme will start once the selected time delay
has expired.
Wash cycle phase indicator lights
Once the desired wash cycle has been selected and has be-
gun, the indicator lights switch on one by one to indicate which
phase of the cycle is currently in progress.
Function buttons and corresponding indicator lights
When a function is selected, the corresponding indicator
light will illuminate.
If the selected function is not compatible with the program-
med wash cycle, the corresponding indicator light will flash
and the function will not be activated.
If the selected function is not compatible with another
function which has been selected previously, the indicator
light corresponding to the first function selected will
flash and only the second function will be activated; the
indicator light corresponding to the enabled option will
remain lit.
Door locked indicator light
When the indicator light is on, the porthole door is locked
to prevent it from being opened; make sure the indicator
light is off before opening the door (wait approximately 3
minutes). To open the door during a running wash cycle,
press the START/PAUSE button; the door may be opened
once the DOOR LOCKED indicator light turns off.
Starting a wash cycle
1. Switch the washing machine on by pressing the ON/OFF button. All indicator lights will switch on for a few seconds, then
they will switch off and the START/PAUSE indicator light will pulse.
2. Load the laundry and close the door.
3. Set the WASH CYCLE knob to the desired programme.
4. Set the washing temperature (see “Personalisation”).
5. Set the spin speed (see “Personalisation”).
6. Measure out the detergent and washing additives (see “Detergents and laundry”).
7. Select the desired functions.
8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit in a fixed
manner, in green.
To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.
9. At the end of the wash cycle the indicator light will switch on. The door can be opened once the DOOR LOCKED
indicator light turns off. Take out your laundry and leave the appliance door ajar to make sure the drum dries completely.
Switch the washing machine off by pressing the ON/OFF button.
Wash
Rinse
Spin
Drain
End of wash cycle
6
GB
Specials wash cycles
Express (wash cycle 10) this wash cycle was designed to wash lightly soiled garments quickly: it lasts just 15 minutes and
therefore saves both energy and time. By selecting this wash cycle (10 at 30°C), it is possible to wash different fabrics toge-
ther (except for wool and silk items), with a maximum load of 1.5 kg.
Sport Intensive (
wash cycle
11) is for washing heavily soiled sports clothing fabrics (tracksuits, shorts, etc.); for best
results, we recommend not exceeding the maximum load indicated in the “Table of wash cycles”.
Sport Light (
wash cycle
12) is for washing lightly soiled sports clothing fabrics (tracksuits, shorts, etc.); for best results,
we recommend not exceeding the maximum load indicated in the “Table of wash cycles”. We recommend using a
liquid detergent and dosage suitable for a half-load.
Sport Shoes (
wash cycle
13) is for washing sports shoes; for best results, do not wash more than 2 pairs simultaneously.
Wash cycles
Table of wash cycles
Wash cycles
Description of the wash cycle
Max.
temp.
(°C)
Max.
speed
(rpm)
Detergents
Max. load
(kg)
Cycle
duration
Prewa-
sh
Wash
Ble-
ach
Fabric
softe-
ner
Nor-
mal
Eco
Time
Nor-
mal
Eco
Time
Daily
1
Cotton with prewash: extremely soiled whites.
90° 1000
-
6 - 145 -
2
Cotton: extremely soiled whites.
90° 1000 -
6 - 125 -
2
Cotton (1-2): heavily soiled whites and resistant colours.
60° 1000 -
6 - 190 -
2
Cotton (2): lightly soiled whites and delicate colours.
40° 1000 -
6 - 185 -
3
Cotton: heavily soiled whites and resistant colours.
60° 1000 -
6 3,5 120 85
4
Coloured Cottons (3): lightly soiled whites and delicate colours.
40° 1000 -
6 3,5 85 60
5
Synthetics: heavily soiled resistant colours.
60° 800 -
2,5 2 110 75
5
Synthetics (4): heavily soiled resistant colours.
40° 800 -
2,5 2 95 70
6
Synthetics: lightly soiled delicate colours.
40° 800 -
2,5 2 70 50
Special
7
Wool: for wool, cashmere, etc.
40° 800 -
-
1,5 - 70 -
8
Silk/Curtains: for garments in silk and viscose, lingerie.
30° 0 -
-
1 - 55 -
9 Jeans
40° 800 -
-
3 - 70 -
10
Express: to refresh lightly soiled garments quickly (not suitable for
wool, silk and clothes which require washing by hand).
30° 800 -
-
1,5 - 15 -
Sport
11 Sport Intensive
30° 600 -
-
3 -
85 -
12 Sport Light
30° 600 -
-
3 -
60 -
13 Sport Shoes
30° 600 -
-
Max. 2
pairs
- 60 -
Partial wash cycles
Rinse
- 1000 - -
6 - 40 -
Spin
- 1000 - - - -
6 - 15 -
Drain
- 0 - - - -
6 - 2 -
The cycle duration indicated on the display or instruction manual is an estimate based on standard conditions. The actual duration may vary
in relation to several factors, such as the temperature and pressure of the incoming water, ambient temperature, amount of detergent, load
quantity and type, load balancing and any additional options selected.
For all Test Institutes:
1) Test wash cycle in compliance with regulation 2010/1061: set wash cycle 2 with a temperature of 60°C and 40°C.
2) Long wash cycle for cottons: set wash cycle 2 with a temperature of 40°C.
3) Short wash cycle for cottons: set wash cycle 4 with a temperature of 40°C.
4) Synthetic program along: set wash cycle 5 with a temperature of 40°C.
7
GB
Setting the temperature
Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles).
The temperature may be lowered, or even set to a cold wash .
The washing machine will automatically prevent you from selecting a temperature which is higher than the maximum value
set for each wash cycle.
Setting the spin speed
Turn the SPIN SPEED knob to set the spin speed for the selected wash cycle.
The maximum spin speeds available for each wash cycle are as follows:
Wash cycles Maximum spin speed
Cottons 1000 rpm
Synthetics 800 rpm
Wool 800 rpm
Silk drain only
The spin speed may be lowered, or the spin cycle can be excluded altogether by selecting the symbol .
The washing machine will automatically prevent you from selecting a spin speed which is higher than the maximum speed
set for each wash cycle.
Functions
The various wash functions available with this washing machine will help to achieve the desired results, every time.
To activate the functions:
1. Press the button corresponding to the desired function;
2. the function is enabled when the corresponding indicator light is illuminated.
Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in conjunction with the
selected wash cycle.
Selecting this option enables you to suitably adjust drum rotation, temperature and water to a reduced load of lightly soiled
cotton and synthetic fabrics (refer to the
“Table of wash cycles”
). “ ” enables you to wash in less time thereby saving
water and electricity. We suggest using a liquid detergent suitably measured out to the load quantity.
! This function may not be used in conjunction with wash cycles 1, 2, 7, 8, 9, 10, 11, 12, 13, , , .
Stain removal
Bleaching cycle designed to remove the toughest stains. Please remember to pour the bleach into extra compartment 4 (see
“Bleach cycle”).
! This function may not be used in conjunction with wash cycles 1, 7, 8, 9, 10, 11, 12, 13, , .
Extra rinse
By selecting this option, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is particularly
useful for sensitive skin.
! This function may not be used in conjunction with wash cycles 10, , .
Delay timer
This timer delays the start time of the wash cycle by up to 12 hours.
Press the button repeatedly until the indicator light corresponding to the desired delay time switches on. The fifth time the button
is pressed, the function will be disabled.
N.B. Once the START/PAUSE button has been pressed, the delay time can only be modified by decreasing it until launching
the set programme.
! This option is enabled with all programmes.
Personalisation
8
GB
Detergents and laundry
Detergent dispenser drawer
Good washing results also depend on the correct dose of
detergent: adding too much detergent will not necessa-
rily result in a more efficient wash, and may in fact cause
build up on the inside of your appliance and contribute to
environmental pollution.
! Do not use hand washing detergents because these
create too much foam.
Open the detergent di-
spenser drawer and pour
in the detergent or washing
additive, as follows.
Compartment 1: Pre-wash detergent (powder)
Before pouring in the detergent, make sure that extra com-
partment 4 has been removed.
compartment 2: Detergent for the wash cycle
(powder or liquid)
Liquid detergent should only be poured in immediately
prior to the start of the wash cycle.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
extra compartment 4: Bleach
Bleach cycle
! Traditional bleach should be used on sturdy white fa-
brics, and delicate bleach for coloured fabrics, synthetics
and for wool.
This option is particularly
useful for the removal of
stubborn stains. Place extra
compartment 4 (supplied)
into compartment 1.
When pouring in the
bleach, be careful not to
exceed the “max” level
marked on the central pivot
(see figure).
To run the bleach cycle on
its own, pour the bleach into extra compartment 4, set the
“Rinse” programme and activate the “Stain removal”
option.
To bleach during a wash cycle, pour in the detergent and
any fabric softener you wish to use, set the desired wash
cycle and enable the “Stain removal” option.
The use of extra compartment 4 excludes the “Pre-wash”
option.
1
2
3
4
Preparing the laundry
• Divide the laundry according to:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
• Empty all garment pockets and check the buttons.
• Do not exceed the listed values, which refer to the weight
of the laundry when dry:
Durable fabrics: max. 6 kg
Synthetic fabrics: max. 2,5 kg
Delicate fabrics: max. 2 kg
Wool: max. 1,5 kg
Silk: max. 1 kg
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g
Garments requiring special care
Wool: all wool garments can be washed using programme
7, even those carrying the “hand-wash only” label. For
best results, use special detergents and do not exceed 1,5
kg of laundry.
Silk: use special wash cycle 8 to wash all silk garments.
We recommend the use of special detergent which has
been designed to wash delicate clothes.
Curtains: fold curtains and place them in a pillow case or
mesh bag. Use wash cycle 8.
Jeans: Turn garments inside-out before washing and use
a liquid detergent. Use programme 9.
Load balancing system
Before every spin cycle, to avoid excessive vibrations and
to distribute the load in a uniform manner, the drum rotates
continuously at a speed which is slightly greater than the
washing rotation speed. If, after several attempts, the load
is not balanced correctly, the machine spins at a reduced
spin speed. If the load is excessively unbalanced, the
washing machine performs the distribution process instead
of spinning. To encourage improved load distribution and
balance, we recommend small and large garments are
mixed in the load.
9
GB
Precautions and tips
! This washing machine was designed and constructed in
accordance with international safety regulations. The fol-
lowing information is provided for safety reasons and must
therefore be read carefully.
General safety
This appliance was designed for domestic use only.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the applian-
ce by a person responsible for their safety. Children should be
supervised to ensure that they do not play with the appliance.
Do not touch the machine when barefoot or with wet or
damp hands or feet.
Do not pull on the power supply cable when unplugging
the appliance from the electricity socket. Hold the plug
and pull.
Do not open the detergent dispenser drawer while the
machine is in operation.
Do not touch the drained water as it may reach extreme-
ly high temperatures.
Never force the porthole door. This could damage the
safety lock mechanism designed to prevent accidental
opening.
If the appliance breaks down, do not under any circum-
stances access the internal mechanisms in an attempt
to repair it yourself.
Always keep children well away from the appliance while
it is operating.
The door can become quite hot during the wash cycle.
If the appliance has to be moved, work in a group of two
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.
Before loading laundry into the washing machine, make
sure the drum is empty.
Disposal
Disposing of the packaging materials: observe local
regulations so that the packaging may be re-used.
The European Directive 2002/96/EC on Waste Electrical
and Electronic Equipment, requires that old household
electrical appliances must not be disposed of in the
normal unsorted municipal waste stream. Old applian-
ces must be collected separately in order to optimise
the recovery and recycling of the materials they contain
and reduce the impact on human health and the envi-
ronment. The crossed out “wheeled bin” symbol on the
product reminds you of your obligation, that when you
dispose of the appliance it must be separately collected.
Consumers should contact their local authority or retailer
for information concerning the correct disposal of their
old appliance.
10
GB
Care and maintenance
Cutting off the water and electricity
supplies
Turn off the water tap after every wash cycle. This will
limit wear on the hydraulic system inside the washing
machine and help to prevent leaks.
Unplug the washing machine when cleaning it and du-
ring all maintenance work.
Cleaning the washing machine
The outer parts and rubber components of the appliance
can be cleaned using a soft cloth soaked in lukewarm
soapy water. Do not use solvents or abrasives.
Cleaning the detergent dispenser drawer
Remove the dispenser by
raising it and pulling it out
(see figure).
Wash it under running wa-
ter; this operation should be
repeated frequently.
Caring for the door and drum of your
appliance
Always leave the porthole door ajar in order to prevent
unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-cleaning pump
which does not require any maintenance. Sometimes, small
items (such as coins or buttons) may fall into the pre-cham-
ber which protects the pump, situated in its bottom part.
! Make sure the wash cycle has finished and unplug the
appliance.
To access the pre-chamber:
1. using a screwdriver,
remove the cover panel
on the lower front part of
the washing machine (see
figure);
2. unscrew the lid by rota-
ting it anti-clockwise (see
figure): a little water may
trickle out. This is perfectly
normal;
3. clean the inside thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks are securely
in place before you push it onto the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If there are any
cracks, it should be replaced immediately: during the wash
cycles, water pressure is very strong and a cracked hose
could easily split open.
! Never use second-hand hoses.
11
GB
Troubleshooting
Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure
that the problem cannot be not solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not
take in water (the indicator light for
the first wash cycle stage flashes
rapidly).
The washing machine continuously
takes in and drains water.
The washing machine does not
drain or spin.
The washing machine vibrates a lot
during the spin cycle.
The washing machine leaks.
The “optionindicator lights and the
“start/pause” indicator light flash,
while one of the “phase in progress”
indicator lights and the “door lo-
ckedindicator light will remain lit in
a fixed manner.
There is too much foam.
Possible causes / Solutions:
The appliance is not plugged into the socket fully, or is not making contact.
There is no power in the house.
The washing machine door is not closed properly.
The ON/OFF button has not been pressed.
The START/PAUSE button has not been pressed.
The water tap has not been opened.
A delayed start has been set (see “Personalisation”).
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap has not been opened.
There is no water supply in the house.
The pressure is too low.
The START/PAUSE button has not been pressed.
The drain hose is not fitted at a height between 65 and 100 cm from the floor
(see “Installation”).
The free end of the hose is under water (see “Installation”).
The wall drainage system is not fitted with a breather pipe.
If the problem persists even after these checks, turn off the water tap, switch
the appliance off and contact the Assistance Service. If the dwelling is on one of
the upper floors of a building, there may be problems relating to water drainage,
causing the washing machine to fill with water and drain continuously. Special
anti-draining valves are available in shops and help to avoid this inconvenience.
The wash cycle does not include draining: some wash cycles require the drain
phase to be started manually.
The drain hose is bent (see “Installation”).
The drainage duct is clogged.
The drum was not unlocked correctly during installation (see “Installation”).
The washing machine is not level (see “Installation”).
The washing machine is trapped between cabinets and walls (see “Installation”).
The water inlet hose is not screwed on properly (see “Installation”).
The detergent dispenser drawer is blocked (for cleaning instructions, see “Care
and maintenance”).
The drain hose is not fixed properly (see “Installation”).
Switch off the machine and unplug it, wait for approximately 1 minute and then
switch it back on again.
If the problem persists, contact the Technical Assistance Service.
The detergent is not suitable for machine washing (it should display the text
“for washing machines” or “hand and machine wash”, or the like).
Too much detergent was used.
12
GB
Service
Before calling for Assistance:
Check whether you can solve the problem alone (see “Troubleshooting”);
Restart the programme to check whether the problem has been solved;
If this is not the case, contact an authorised Technical Assistance Centre using the telephone number provided on the
guarantee certificate.
! Always request the assistance of authorised technicians.
Have the following information to hand:
the type of problem;
the appliance model (Mod.);
the serial number (S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the
front of the appliance by opening the door.
13
ES
Español
Sumario
Instalación, 14-15
Desembalaje y nivelación
Conexiones hidráulicas y eléctricas
Primer ciclo de lavado
Datos técnicos
Descripción de la lavadora y comienzo
de un programa, 16-17
Panel de control
Pilotos
Poner en marcha un programa
Programas, 18
Tabla de programas
Personalizaciones, 19
Seleccionar la temperatura
Seleccionar el centrifugado
Funciones
Detergentes y ropa, 20
Contenedor de detergentes
Ciclo de blanqueo
Preparar la ropa
Prendas especiales
Sistema de equilibrado de la carga
Precauciones y consejos, 21
Seguridad general
Eliminaciones
Mantenimiento y cuidados, 22
Interrumpir el agua y la corriente eléctrica
Limpiar la lavadora
Limpiar el contenedor de detergentes
Cuidar la puerta y el cesto
Limpiar la bomba
Controlar el tubo de alimentación de agua
Anomalías y soluciones, 23
Asistencia, 24
ES
IWC 6105
Manual de instrucciones
LAVADORA
14
ES
Instalación
! Es importante conservar este manual para poder consul-
tarlo en cualquier momento. En caso de venta, de cesión o
de traslado, verifique que permanezca junto con la lava-
dora para informar al nuevo propietario sobre el funciona-
miento y brindar las correspondientes advertencias.
! Lea atentamente las instrucciones: ellas contienen
importante información sobre la instalación, el uso y la
seguridad.
Desembalaje y nivelación
Desembalaje
1. Desembale la lavadora.
2. Controle que la lavadora no haya sufrido daños durante
el transporte. Si estuviera dañada no la conecte y llame al
revendedor.
3. Quite los 4 tornillos de
protección para el transpor-
te y la arandela de goma
con el correspondiente
distanciador ubicados en
la parte posterior (ver la
figura).
4. Cubra los orificios con los tapones de plástico sumini-
strados con el aparato.
5. Conserve todas las piezas: cuando la lavadora deba ser
transportada nuevamente, deberán volver a colocarse.
! Los embalajes no son juguetes para los niños.
Nivelación
1. Instale la lavadora sobre un piso plano y rígido, sin apo-
yarla en las paredes, muebles ni en ningún otro aparato.
2. Si el piso no está perfec-
tamente horizontal, com-
pense las irregularidades
desenroscando o enro-
scando las patas delanteras
(ver la figura); el ángulo de
inclinación medido sobre
la superficie de trabajo, no
debe superar los 2º.
Una cuidadosa nivelación
brinda estabilidad a la
máquina y evita vibraciones, ruidos y desplazamientos du-
rante el funcionamiento. Cuando se instala sobre moque-
tas o alfombras, regule los pies para conservar debajo de
la lavadora un espacio suficiente para la ventilación.
Conexiones hidráulicas y eléctricas
Conexión del tubo de alimentación de agua
1. Conectar el tubo de tubo
enroscándolo a un grifo de
agua fría con la boca rosca-
da de 3/4 gas (ver la figura).
Antes de conectarlo, haga
correr el agua hasta que
esté límpida.
2. Conecte el tubo de
alimentación a la lavadora
enroscándolo en la toma
de agua correspondiente
ubicada en la parte poste-
rior derecha (arriba) (ver la
figura).
3. Controle que en el tubo no hayan pliegues ni estrangu-
laciones.
! La presión de agua del grifo debe estar comprendida
dentro de los valores contenidos en la tabla de Datos
técnicos (ver la página correspondiente).
! Si la longitud del tubo de alimentación no es la suficiente,
diríjase a un negocio especializado o a un técnico autori-
zado.
! No utilice nunca tubos ya usados.
! Utilice los suministrados con la máquina.
15
ES
65 - 100 cm
Conexión del tubo de descarga
Conecte el tubo de de-
scarga, sin plegarlo, a una
tubería de descarga o a una
descarga de pared colo-
cadas a una altura del piso
entre 65 y 100 cm;
o apóyelo en el borde
de un lavamanos o de
una bañera, uniendo la
guía suministrada con el
aparato, al grifo (ver la
figura). El extremo libre del
tubo de descarga no debe
permanecer sumergido en
el agua.
! No se aconseja utilizar tubos de prolongación, si fuera in-
dispensable hacerlo, la prolongación debe tener el mismo
diámetro del tubo original y no superar los 150 cm.
Conexión eléctrica
Antes de enchufar el aparato, verifique que:
la toma tenga la conexión a tierra y haya sido hecha
según las normas legales;
la toma sea capaz de soportar la carga máxima de
potencia de la máquina indicada en la tabla de Datos
técnicos (ver al costado);
la tensión de alimentación esté comprendida dentro de
los valores indicados en la tabla de Datos técnicos (ver
al costado);
la toma sea compatible con el enchufe de la lavadora. Si
no es así, sustituya la toma o el enchufe.
! La lavadora no debe ser instalada al aire libre, ni siquiera
si el lugar está reparado, ya que es muy peligroso dejarla
expuesta a la lluvia o a las tormentas.
! Una vez instalada la lavadora, la toma de corriente debe
ser fácilmente accesible.
! No utilice prolongaciones ni conexiones múltiples.
! El cable no debe estar plegado ni sufrir compresiones.
! El cable de alimentación debe ser sustituido sólo por
técnicos autorizados.
¡Atención! La empresa fabricante declina toda responsabi-
lidad en caso de que estas normas no sean respetadas.
Primer ciclo de lavado
Después de la instalación y antes del uso, realice un ciclo
de lavado con detergente y sin ropa, seleccionando el
programa 2.
Datos técnicos
Modelo
IWC 6105
Dimensiones
ancho 59,5 cm.
altura 85 cm.
profundidad 53,5 cm.
Capacidad
de 1 a 6 kg.
Conexiones
eléctricas
ver la placa de características técnicas
aplicada en la máquina
Conexiones
hídricas
presión máxima 1 MPa (10 bar)
presión mínima 0,05 MPa (0,5 bar)
capacidad del cesto 52 litros
Velocidad de
centrifugado
máxima 1000 r.p.m.
Programas de
prueba según
la directiva
2010/1061
Programa 2: temperatura 60°C y 40°C.
Esta máquina cumple con lo establecido
por las siguientes Directivas de la Comu-
nidad:
- 2004/108/CE (Compatibilidad Electro-
magnética)
- 2002/96/CE
- 2006/95/CE (Baja Tensión)
16
ES
Contenedor de detergentes: para cargar detergentes y
aditivos (ver “Detergentes y ropa”).
Botón de ENCENDIDO/APAGADO: para encender y
apagar la lavadora.
Mando de PROGRAMAS: para elegir los programas. Duran-
te el funcionamiento del programa el mando no se mueve.
Botones con pilotos de FUNCIÓN: para seleccionar las
funciones disponibles. El piloto correspondiente a la función
seleccionada permanecerá encendido.
Mando de CENTRIFUGADO: para seleccionar el centrifu-
gado o excluirlo (ver “Personalizaciones”).
Mando de TEMPERATURA: para seleccionar la temperatura
o el lavado en frío (ver “Personalizaciones”).
Pilotos DE AVANCE DEL CICLO/COMIENZO RETRA-
SADO: para seguir el estado de avance del programa de
lavado. El piloto encendido indica la fase en curso.
Si se seleccionó la función “Comienzo retrasado”, indicarán
el tiempo que falta para la puesta en marcha del programa
(ver la página correspondiente).
Piloto PUERTA BLOQUEADA: para saber si la puerta se
puede abrir (ver la página correspondiente).
Botón con piloto PUESTA EN MARCHA/PAUSA: se
utiliza para poner en marcha los programas o interrumpirlos
momentáneamente.
Nota: Presione este botón para poner en pausa el lavado
en curso, el piloto correspondiente centelleará con color
anaranjado mientras que el de la fase en curso permanecerá
encendido en forma fija. Si el piloto PUERTA BLOQUEADA
está apagado, se podrá abrir la puerta.
Para que el lavado se reanude a partir del momento en el cual
fue interrumpido, presione nuevamente este botón.
Modalidad de stand by
Esta lavasecadora está en conformidad con las nuevas
normativas vinculadas al ahorro energético. Está dotada
de un sistema de auto-apagado (stand by) que, en caso de
no funcionamiento, se activa pasados aproximadamente
30 minutos. Presionar brevemente el botón ENCENDIDO/
APAGADO y esperar que la máquina se active.
Descripción de la lavadora y
comienzo de un programa
Piloto PUERTA
BLOQUEADA
Botón con piloto
PUESTA EN
MARCHA/
PAUSA
Panel de control
Contenedor de detergentes
Botón de
ENCENDIDO/
APAGADO
Mando de
PROGRAMAS
Botones con pilotos
FUNCIÓN
Mando de
TEMPERATURA
Mando de
CENTRIFUGADO
Pilotos DE AVANCE DEL
CICLO/COMIENZO
RETRASADO
17
ES
Pilotos
Los pilotos suministran información importante.
He aquí lo que nos dicen:
Comienzo retrasado
Si se ha activado la función “Comienzo retrasado” (ver “Per-
sonalizaciones”), después de haber puesto en marcha el
programa, comenzará a centellear el piloto correspondien-
te al retraso seleccionado:
Con el transcurrir del tiempo se visualizará el retraso resi-
dual con el centelleo de la luz testigo correspondiente:
Una vez transcurrido el tiempo de retraso seleccionado,
comenzará el programa.
Pilotos fase en curso
Una vez seleccionado y puesto en marcha el ciclo de
lavado deseado, las luces testigo se encenderán progresi-
vamente para indicar su estado de avance:
Botones de función y pilotos correspondientes
Seleccionando una función, el piloto correspondiente se
iluminará. Si la función seleccionada no es compatible con
el programa elegido, el piloto correspondiente centelleará y
la función no se activará. Si la función elegida no es com-
patible con otra seleccionada precedentemente, el piloto
correspondiente a la primera función seleccionada centel-
leará y se activará sólo la segunda, el piloto de la función
activada se iluminará.
Piloto puerta bloqueada
El piloto encendido indica que la puerta está bloqueada
impidiendo su apertura; para poder abrir la puerta es ne-
cesario que dicho piloto esté apagado (espere 3 minutos
aproximadamente). Para abrir la puerta mientras un ciclo
está en curso, presione el botón PUESTA EN MARCHA/
PAUSA; si el piloto PUERTA BLOQUEADA está apagado,
será posible abrir la puerta.
Poner en marcha un programa
1. Encienda la lavadora presionando el botón ENCENDIDO/APAGADO. Todos los pilotos se encenderán durante algunos
segundos, luego se apagarán y se deberá pulsar el piloto PUESTA EN MARCHA/PAUSA.
2. Cargue la ropa y cierre la puerta.
3. Seleccione el programa deseado con el mando de PROGRAMAS.
4. Fije la temperatura de lavado (ver “Personalizaciones”).
5. Fije la velocidad de centrifugado (ver “Personalizaciones”).
6. Vierta detergente y aditivos (ver “Detergentes y ropa”).
7. Seleccione las funciones deseadas.
8. Ponga en marcha el programa presionando el botón PUESTA EN MARCHA/PAUSA y el piloto correspondiente perma-
necerá encendido, fijo y de color verde. Para anular el ciclo seleccionado ponga en pausa la máquina presionando el botón
PUESTA EN MARCHA/PAUSA y elija un nuevo ciclo.
9. Al final del programa se iluminará el piloto . Cuando el piloto PUERTA BLOQUEADA se apague, será posible abrir la
puerta. Extraiga la ropa y deje la puerta semicerrada para permitir que el cesto se seque.
Apague la lavadora presionando el botón ENCENDIDO/APAGADO.
Lavado
Aclarado
Centrifugado
Descarga
Fin del Lavado
18
ES
Programas particulares
Express (programa 10) fue estudiado para lavar prendas ligeramente sucias y en poco tiempo: dura sólo 15 minutos
y de esa manera permite ahorrar energía y tiempo. Seleccionando el programa (10 a 30ºC) es posible lavar conjunta-
mente tejidos de distinto tipo (excluidas lana y seda), con una carga máxima de 1,5 kg.
Sport Intensive (programa 11) ha sido estudiado para lavar tejidos usados en prendas deportivas (chándales, pantalo-
nes cortos, etc.) muy sucios; para obtener los mejores resultados es aconsejable no superar la carga máxima indicada
en la “Tabla de programas”.
Sport Light (programa 12) ha sido estudiado para lavar tejidos usados en prendas deportivas (chándales, pantalones
cortos, etc.) poco sucios; para obtener los mejores resultados es aconsejable no superar la carga máxima indicada en
la “Tabla de programas”. Se recomienda utilizar detergente líquido y la dosis correspondiente a la media carga.
Sport Shoes (programa 13) ha sido estudiado para lavar calzado deportivo; para obtener los mejores resultados no
lave más de 2 pares a la vez.
Programas
Tabla de programas
Programas
Descripción del Programa
Temp.
max.
(°C)
Velocidad
máx.
(r.p.m.)
Detergentes
Carga máx.
(Kg.)
Duración
del ciclo
Prela-
vado
Lava-
do
Blan-
quea-
dor
Sua-
vi-
zante
Nor-
mal
Eco
Time
Nor-
mal
Eco
Time
Diario (programas para todos los días)
1
Prelavado Algodón: blancos sumamente sucios.
90° 1000
-
6 - 145 -
2
Algodón: blancos sumamente sucios.
90° 1000 -
6 - 125 -
2
Algodón (1-2): blancos y colores resistentes muy sucios.
60° 1000 -
6 - 190 -
2
Algodón (2): blancos y colores delicados poco sucios.
40° 1000 -
6 - 185 -
3
Algodón: blancos sumamente sucios.
60° 1000 -
6 3,5 120 85
4
Algodón de color (3): blancos poco sucios y colores delicados.
40° 1000 -
6 3,5 85 60
5
Sintético: colores resistentes muy sucios.
60° 800 -
2,5 2 110 75
5
Sintético (4): colores resistentes muy sucios.
40° 800 -
2,5 2 95 70
6
Sintético: colores delicados poco sucios.
40° 800 -
2,5 2 70 50
Programas Especiales
7
Lana: para lana, cachemira, etc.
40° 800 -
-
1,5 - 70 -
8
Seda/Cortinas: para prendas de seda, viscosa, lencería.
30° 0 -
-
1 - 55 -
9 Jeans
40° 800 -
-
3 - 70 -
10
Express: para refrescar rápidamente prendas poco sucias (no se
aconseja utilizarlo para lana, seda y prendas para lavar a mano).
30° 800 -
-
1,5 - 15 -
Sport
11 Sport Intensive
30° 600 -
-
3 -
85 -
12 Sport Light
30° 600 -
-
3 -
60 -
13 Sport Shoes
30° 600 -
-
Max. 2
pares
- 60 -
Programas Parciales
Aclarado
- 1000 - -
6 - 40 -
Centrifugado
- 1000 - - - -
6 - 15 -
Descarga
- 0 - - - -
6 - 2 -
La duración del ciclo que se indica en el visor o en el manual es una estimación calculada en base a condiciones estándar. El tiempo efectivo puede
variar en función de numerosos factores como la temperatura y la presión del agua de entrada, la temperatura ambiente, la cantidad de detergente,
la cantidad y el tipo de carga, el equilibrado de la carga y las opciones adicionales seleccionadas.
Para todos los Test Institutes:
1) Programa de control según la norma 2010/1061: seleccione el programa 2 con una temperatura de 60ºC y 40°C.
2) Programa algodón largo: seleccione el programa 2 con una temperatura de 40ºC.
3) Programa algodón corto: seleccione el programa 4 con una temperatura de 40ºC.
4) Programa Sintético de largo: seleccione el programa 5 con una temperatura de 40ºC.
19
ES
Seleccionar la temperatura
Girando el mando de la TEMPERATURA se selecciona la temperatura de lavado (ver la Tabla de programas).
La temperatura se puede disminuir hasta el lavado en frío ( ).
La máquina impedirá automáticamente seleccionar una temperatura mayor que la máxima prevista para cada programa.
Seleccionar el centrifugado
Girando el mando de CENTRIFUGADO se selecciona la velocidad de centrifugado del programa seleccionado.
Las velocidades máximas previstas para los programas son:
Programas Velocidad máxima
Algodón 1000 r.p.m.
Sintéticos 800 r.p.m.
Lana 800 r.p.m.
Seda sólo descarga
Se puede disminuir la velocidad de centrifugado o excluirlo seleccionando el símbolo .
La máquina impedirá automáticamente efectuar un centrifugado a una velocidad mayor que la máxima prevista para cada
programa.
Funciones
Las distintas funciones de lavado previstas por la lavadora permiten obtener la limpieza y el blanco deseados.
Para activar las funciones:
1. presione el botón correspondiente a la función deseada;
2. el encendido del piloto correspondiente indica que la función está activa.
Nota: El centelleo rápido del piloto indica que la función correspondiente no se puede seleccionar para el programa elegido.
Seleccionando esta opción, se optimizan el movimiento mecánico, la temperatura y el agua para una carga reducida de
prendas de algodón y sintéticas poco sucias (ver la “Tabla de programas”).
Con “ ” se puede lavar en un tiempo menor, ahorrando agua y energía. Se aconseja utilizar una dosis de detergente
líquido adecuada a la cantidad de carga.
! No se puede activar con los programas 1, 2, 7, 8, 9, 10, 11, 12, 13, , , .
Antimancha
Ciclo de blanqueo adecuado para eliminar las manchas más resistentes. Recuerde verter el blanqueador en la cubeta adicio-
nal 4 (ver “Ciclo de blanqueo”).
! No se puede activar con los programas 1, 7, 8, 9, 10, 11, 12, 13, , .
Aclarado extra
Al elegir esta función aumentará la eficacia del aclarado y se asegurará la máxima eliminación del detergente. Es útil para
pieles particularmente sensibles.
! No se puede activar con los programas 10, , .
Comienzo retrasado
Retrasa la puesta en marcha de la máquina hasta 12 horas.
Presione varias veces el botón hasta hacer encender la luz testigo correspondiente al retraso deseado. La quinta vez que se
presione el botón, la función se desactivará.
Nota: Una vez presionado el botón PUESTA EN MARCHA/PAUSA, se puede modificar el valor del retraso sólo disminuyéndolo
hasta que se ponga en marcha el programa seleccionado.
! Se puede utilizar en todos los programas.
Personalizaciones
20
ES
Detergentes y ropa
Contenedor de detergentes
El buen resultado del lavado depende también de la cor-
recta dosificación del detergente: si se excede la cantidad,
no se lava de manera más eficaz, sino que se contribuye a
encostrar las partes internas de la lavadora y a contaminar
el medio ambiente.
! No use detergentes para el lavado a mano porque pro-
ducen demasiada espuma.
Extraiga el contenedor de
detergentes e introduzca el
detergente o el aditivo de la
siguiente manera:
cubeta 1: Detergente para prelavado (en polvo)
Antes de verter el detergente, verifique que no esté colo-
cada la cubeta adicional 4.
cubeta 2: Detergente para lavado (en polvo o
líquido)
El detergente líquido se debe verter sólo antes de la pue-
sta en marcha.
cubeta 3: Aditivos (suavizante, etc.)
El suavizante no se debe volcar fuera de la rejilla.
cubeta adicional 4: Blanqueador
Ciclo de blanqueo
! El blanqueador tradicional debe utilizarse para los teji-
dos resistentes blancos, mientras que el delicado debe
utilizarse para la lana y los tejidos coloreados y sintéticos.
Introduzca la cubeta adicio-
nal 4 suministrada con el
aparato, en la cubeta 1.
Al verter el blanqueador
no debe superar el nivel
máx.” indicado en el per-
no central (véase la figura).
Para realizar sólo el blanqueo, vierta el blanqueador en la
cubeta adicional 4, seleccione el programa “Aclarado” y
active la función “Antimancha” .
Para blanquear durante el lavado, vierta el detergente y
los aditivos, seleccione el programa deseado y active la
función “Antimancha” .
El uso de la cubeta adicional 4 excluye el prelavado.
1
2
3
4
Preparar la ropa
Subdivida la ropa según:
- el tipo de tejido / el símbolo en la etiqueta.
- los colores: separe las prendas de color y las blancas.
Vacíe los bolsillos y controle los botones.
No supere los valores indicados, referidos al peso de la
ropa seca:
Tejidos resistentes: max 6 kg.
Tejidos sintéticos: max 2,5 kg.
Tejidos delicados: max 2 kg.
Lana: max 1,5 kg.
Seda: max 1 kg.
¿Cuánto pesa la ropa?
1 sábana 400/500 g
1 funda 150/200 g
1 mantel 400/500 g
1 albornoz 900/1200 g
1 toalla 150/250 g
Prendas especiales
Lana: con el programa 7 es posible lavar en la lavadora
todas las prendas de lana, aún las que contienen la eti-
queta “sólo lavado a mano” Para obtener los mejores
resultados utilice un detergente específico y no supere
1,5 Kg. de ropa.
Seda: utilice el programa correspondiente 8 para lavar
todas las prendas de seda. Se aconseja el uso de un
detergente específico para prendas delicadas.
Cortinas: pliéguelas y colóquelas dentro de una funda o
de una bolsa de red. Utilice el programa 8.
Jeans: vuelva del revés las prendas antes del lavado y
utilice un detergente líquido. Utilice el programa 9.
Sistema de equilibrado de la carga
Antes de cada centrifugado, para evitar vibraciones exce-
sivas y para distribuir la carga de modo uniforme, el cesto
realiza rotaciones a una velocidad ligeramente superior a la
del lavado. Si después de varios intentos, la carga todavía
no está correctamente equilibrada, la máquina realiza el
centrifugado a una velocidad inferior a la prevista. Cuando
existe un excesivo desequilibrio, la lavadora realiza la
distribución antes que el centrifugado. Para obtener una
mejor distribución de la carga y su correcto equilibrado, se
aconseja mezclar prendas grandes y pequeñas.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60

Indesit IWC 6105 (EU) Guida utente

Categoria
Lavatrici
Tipo
Guida utente