Indesit IWC 6105 (EU) Guida utente

Marca: Indesit

Modello: IWC 6105 (EU)

Categoria: Lavatrici

Tipo: Guida utente

Contents

Installation, 2-3

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Description of the washing machine

and starting a wash cycle, 4-5

Control panel

Indicator lights

Starting a wash cycle

Wash cycles, 6

Table of wash cycles

Personalisation, 7

Setting the temperature

Setting the spin speed

Functions

Detergents and laundry, 8

Detergent dispenser drawer

Bleach cycle

Preparing the laundry

Garments requiring special care

Load balancing system

Precautions and tips, 9

General safety

Disposal

Care and maintenance, 10

Cutting off the water or electricity supply

Cleaning the washing machine

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Troubleshooting, 11

Service, 12

IWC 6105

Instructions for use

WASHING MACHINE

English,1

Espańol,13

Polski,25

Portuguęs,37

Italiano,49

Installation

! This instruction manual should be kept in a safe place for

future reference. If the washing machine is sold, transferred

or moved, make sure that the instruction manual remains

with the machine so that the new owner is able to familiari-

se himself/herself with its operation and features.

! Read these instructions carefully: they contain vital infor-

mation relating to the safe installation and operation of the

appliance.

Unpacking and levelling

Unpacking

1. Remove the washing machine from its packaging.

2. Make sure that the washing machine has not been

damaged during the transportation process. If it has been

damaged, contact the retailer and do not proceed any

further with the installation process.

3. Remove the 4 protective

screws (used during tran-

sportation) and the rubber

washer with the correspon-

ding spacer, located on the

rear part of the appliance

(see figure).

4. Close off the holes using the plastic plugs provided.

5. Keep all the parts in a safe place: you will need them

again if the washing machine needs to be moved to ano-

ther location.

! Packaging materials should not be used as toys for

children.

Levelling

1. Install the washing machine on a flat sturdy floor, without

resting it up against walls, furniture cabinets or anything

else.

2. If the floor is not perfectly

level, compensate for any

unevenness by tightening

or loosening the adjusta-

ble front feet (see figure);

the angle of inclination,

measured in relation to the

worktop, must not exceed

2°.

Levelling the machine correctly will provide it with stability,

help to avoid vibrations and excessive noise and prevent it

from shifting while it is operating. If it is placed on carpet or

a rug, adjust the feet in such a way as to allow a sufficient

ventilation space underneath the washing machine.

Connecting the electricity and water

supplies

Connecting the water inlet hose

1. Connect the supply pipe

by screwing it to a cold

water tap using a ¾ gas

threaded connection (see

figure).

Before performing the con-

nection, allow the water to

run freely until it is perfectly

clear.

2. Connect the inlet hose

to the washing machine by

screwing it onto the corre-

sponding water inlet of the

appliance, which is situa-

ted on the top right-hand

side of the rear part of the

appliance (see figure).

3. Make sure that the hose is not folded over or bent.

! The water pressure at the tap must fall within the values

indicated in the Technical details table (see next page).

! If the inlet hose is not long enough, contact a specialised

shop or an authorised technician.

! Never use second-hand hoses.

! Use the ones supplied with the machine.

65 - 100 cm

Connecting the drain hose

Connect the drain hose,

without bending it, to a drai-

nage duct or a wall drain

located at a height between

65 and 100 cm from the

floor;

alternatively, rest it on

the side of a washbasin

or bathtub, fastening the

duct supplied to the tap

(see figure). The free end

of the hose should not be

underwater.

! We advise against the use of hose extensions; if it is

absolutely necessary, the extension must have the same

diameter as the original hose and must not exceed 150 cm

in length.

Electrical connections

Before plugging the appliance into the electricity socket,

make sure that:

• the socket is earthed and complies with all applicable

laws;

• the socket is able to withstand the maximum power load

of the appliance as indicated in the Technical data table

(see opposite);

• the power supply voltage falls within the values indicated

in the Technical data table (see opposite);

• the socket is compatible with the plug of the washing

machine. If this is not the case, replace the socket or the

plug.

! The washing machine must not be installed outdoors,

even in covered areas. It is extremely dangerous to leave

the appliance exposed to rain, storms and other weather

conditions.

! When the washing machine has been installed, the elec-

tricity socket must be within easy reach.

! Do not use extension cords or multiple sockets.

! The cable should not be bent or compressed.

! The power supply cable must only be replaced by autho-

rised technicians.

Warning! The company shall not be held responsible in the

event that these regulations are not respected.

The first wash cycle

Once the appliance has been installed, and before you use

it for the first time, run a wash cycle with detergent and no

laundry, using the wash cycle 2.

Technical data

Model

IWC 6105

Dimensions

width 59.5 cm

height 85 cm

depth 53,5 cm

Capacity

from 1 to 6 kg

Electrical

connections

please refer to the technical data plate

fixed to the machine

Water connection

maximum pressure 1 MPa (10 bar)

minimum pressure 0.05 MPa (0.5 bar)

drum capacity 52 litres

Spin speed

up to 1000 rotations per minute

Test

Programmes

according to

2010/1061

Programme 2: temperature 60°C and

40°C

This appliance conforms to the following

EC Directives:

- 2004/108/EC (Electromagnetic Compa-

tibility)

- 2002/96/EC

- 2006/95/EC (Low Voltage)

Detergent dispenser drawer: used to dispense deter-

gents and washing additives (see “Detergents and laundry”).

ON/OFF button: switches the washing machine on and off.

WASH CYCLE knob: programmes the wash cycles. During

the wash cycle, the knob does not move.

FUNCTION buttons with indicator light: used to select the

available functions. The indicator light corresponding to the

selected function will remain lit.

TEMPERATURE knob: sets the temperature or the cold

wash cycle (see “Personalisation”).

SPIN SPEED knob: sets the spin speed or exclude the spin

cycle completely (see “Personalisation”).

WASH CYCLE PROGRESS/DELAY TIMER

indicator

light

s: used to monitor the progress of the wash cycle.

The illuminated indicator light shows which phase is in pro-

gress.

If the Delay Timer function has been set, the time remaining

until the wash cycle starts will be indicated (see next page).

DOOR LOCKED indicator light: indicates whether the door

may be opened or not (see next page).

START/PAUSE button with indicator light: starts or tempo-

rarily interrupts the wash cycles.

N.B. To pause the wash cycle in progress, press this button;

the corresponding indicator light will flash orange, while the

indicator light for the current wash cycle phase will remain lit

in a fixed manner. If the DOOR LOCKED indicator light is

switched off, the door may be opened.

To start the wash cycle from the point at which it was inter-

rupted, press this button again.

Standby mode

This washing machine, in compliance with new energy sa-

ving regulations, is fitted with an automatic standby system

which is enabled after about 30 minutes if no activity is

detected. Press the ON-OFF button briefly and wait for the

machine to start up again.

Description of the washing

machine and starting a wash cycle

WASH CYCLE PROGRESS/

DELAY TIMER indicator lights

DOOR LOCKED

indicator light

START/

PAUSE

button with

indicator light

Control panel

Detergent dispenser drawer

ON/OFF

button

WASH CYCLE

knob

TEMPERATURE

knob

FUNCTION

buttons with

indicator lights

SPIN SPEED

knob

Indicator lights

The indicator lights provide important information.

This is what they can tell you:

Delayed start

If the DELAY TIMER function has been activated (see “Per-

sonalisation”), after the wash cycle has been started the

indicator light corresponding to the selected delay period

will begin to flash:

As time passes, the remaining delay will be displayed and

the corresponding indicator light will flash:

The set programme will start once the selected time delay

has expired.

Wash cycle phase indicator lights

Once the desired wash cycle has been selected and has be-

gun, the indicator lights switch on one by one to indicate which

phase of the cycle is currently in progress.

Function buttons and corresponding indicator lights

When a function is selected, the corresponding indicator

light will illuminate.

If the selected function is not compatible with the program-

med wash cycle, the corresponding indicator light will flash

and the function will not be activated.

If the selected function is not compatible with another

function which has been selected previously, the indicator

light corresponding to the first function selected will

flash and only the second function will be activated; the

indicator light corresponding to the enabled option will

remain lit.

Door locked indicator light

When the indicator light is on, the porthole door is locked

to prevent it from being opened; make sure the indicator

light is off before opening the door (wait approximately 3

minutes). To open the door during a running wash cycle,

press the START/PAUSE button; the door may be opened

once the DOOR LOCKED indicator light turns off.

Starting a wash cycle

1. Switch the washing machine on by pressing the ON/OFF button. All indicator lights will switch on for a few seconds, then

they will switch off and the START/PAUSE indicator light will pulse.

2. Load the laundry and close the door.

3. Set the WASH CYCLE knob to the desired programme.

4. Set the washing temperature (see “Personalisation”).

5. Set the spin speed (see “Personalisation”).

6. Measure out the detergent and washing additives (see “Detergents and laundry”).

7. Select the desired functions.

8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit in a fixed

manner, in green.

To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.

9. At the end of the wash cycle the indicator light will switch on. The door can be opened once the DOOR LOCKED

indicator light turns off. Take out your laundry and leave the appliance door ajar to make sure the drum dries completely.

Switch the washing machine off by pressing the ON/OFF button.

Wash

Rinse

Spin

Drain

End of wash cycle

Specials wash cycles

Express (wash cycle 10) this wash cycle was designed to wash lightly soiled garments quickly: it lasts just 15 minutes and

therefore saves both energy and time. By selecting this wash cycle (10 at 30°C), it is possible to wash different fabrics toge-

ther (except for wool and silk items), with a maximum load of 1.5 kg.

Sport Intensive (

wash cycle

11) is for washing heavily soiled sports clothing fabrics (tracksuits, shorts, etc.); for best

results, we recommend not exceeding the maximum load indicated in the “Table of wash cycles”.

Sport Light (

wash cycle

12) is for washing lightly soiled sports clothing fabrics (tracksuits, shorts, etc.); for best results,

we recommend not exceeding the maximum load indicated in the “Table of wash cycles”. We recommend using a

liquid detergent and dosage suitable for a half-load.

Sport Shoes (

wash cycle

13) is for washing sports shoes; for best results, do not wash more than 2 pairs simultaneously.

Wash cycles

Table of wash cycles

Wash cycles

Description of the wash cycle

Max.

temp.

(°C)

Max.

speed

(rpm)

Detergents

Max. load

(kg)

Cycle

duration

Prewa-

Wash

Ble-

ach

Fabric

softe-

ner

Nor-

mal

Eco

Time

Nor-

mal

Eco

Time

Daily

Cotton with prewash: extremely soiled whites.

90° 1000

 



6 - 145 -

Cotton: extremely soiled whites.

90° 1000 -

  

6 - 125 -

Cotton (1-2): heavily soiled whites and resistant colours.

60° 1000 -

  

6 - 190 -

Cotton (2): lightly soiled whites and delicate colours.

40° 1000 -

  

6 - 185 -

Cotton: heavily soiled whites and resistant colours.

60° 1000 -

  

6 3,5 120 85

Coloured Cottons (3): lightly soiled whites and delicate colours.

40° 1000 -

  

6 3,5 85 60

Synthetics: heavily soiled resistant colours.

60° 800 -

  

2,5 2 110 75

Synthetics (4): heavily soiled resistant colours.

40° 800 -

  

2,5 2 95 70

Synthetics: lightly soiled delicate colours.

40° 800 -

  

2,5 2 70 50

Special

Wool: for wool, cashmere, etc.

40° 800 -



1,5 - 70 -

Silk/Curtains: for garments in silk and viscose, lingerie.

30° 0 -



1 - 55 -

9 Jeans

40° 800 -



3 - 70 -

Express: to refresh lightly soiled garments quickly (not suitable for

wool, silk and clothes which require washing by hand).

30° 800 -



1,5 - 15 -

Sport

11 Sport Intensive

30° 600 -



3 -

85 -

12 Sport Light

30° 600 -



3 -

60 -

13 Sport Shoes

30° 600 -



Max. 2

pairs

- 60 -

Partial wash cycles

Rinse

- 1000 - -

 

6 - 40 -

Spin

- 1000 - - - -

6 - 15 -

Drain

- 0 - - - -

6 - 2 -

The cycle duration indicated on the display or instruction manual is an estimate based on standard conditions. The actual duration may vary

in relation to several factors, such as the temperature and pressure of the incoming water, ambient temperature, amount of detergent, load

quantity and type, load balancing and any additional options selected.

For all Test Institutes:

1) Test wash cycle in compliance with regulation 2010/1061: set wash cycle 2 with a temperature of 60°C and 40°C.

2) Long wash cycle for cottons: set wash cycle 2 with a temperature of 40°C.

3) Short wash cycle for cottons: set wash cycle 4 with a temperature of 40°C.

4) Synthetic program along: set wash cycle 5 with a temperature of 40°C.

Setting the temperature

Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles).

The temperature may be lowered, or even set to a cold wash .

The washing machine will automatically prevent you from selecting a temperature which is higher than the maximum value

set for each wash cycle.

Setting the spin speed

Turn the SPIN SPEED knob to set the spin speed for the selected wash cycle.

The maximum spin speeds available for each wash cycle are as follows:

Wash cycles Maximum spin speed

Cottons 1000 rpm

Synthetics 800 rpm

Wool 800 rpm

Silk drain only

The spin speed may be lowered, or the spin cycle can be excluded altogether by selecting the symbol .

The washing machine will automatically prevent you from selecting a spin speed which is higher than the maximum speed

set for each wash cycle.

Functions

The various wash functions available with this washing machine will help to achieve the desired results, every time.

To activate the functions:

1. Press the button corresponding to the desired function;

2. the function is enabled when the corresponding indicator light is illuminated.

Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in conjunction with the

selected wash cycle.

Selecting this option enables you to suitably adjust drum rotation, temperature and water to a reduced load of lightly soiled

cotton and synthetic fabrics (refer to the

“Table of wash cycles”

). “ ” enables you to wash in less time thereby saving

water and electricity. We suggest using a liquid detergent suitably measured out to the load quantity.

! This function may not be used in conjunction with wash cycles 1, 2, 7, 8, 9, 10, 11, 12, 13, , , .

Stain removal

Bleaching cycle designed to remove the toughest stains. Please remember to pour the bleach into extra compartment 4 (see

“Bleach cycle”).

! This function may not be used in conjunction with wash cycles 1, 7, 8, 9, 10, 11, 12, 13, , .

Extra rinse

By selecting this option, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is particularly

useful for sensitive skin.

! This function may not be used in conjunction with wash cycles 10, , .

Delay timer

This timer delays the start time of the wash cycle by up to 12 hours.

Press the button repeatedly until the indicator light corresponding to the desired delay time switches on. The fifth time the button

is pressed, the function will be disabled.

N.B. Once the START/PAUSE button has been pressed, the delay time can only be modified by decreasing it until launching

the set programme.

! This option is enabled with all programmes.

Personalisation

Detergents and laundry

Detergent dispenser drawer

Good washing results also depend on the correct dose of

detergent: adding too much detergent will not necessa-

rily result in a more efficient wash, and may in fact cause

build up on the inside of your appliance and contribute to

environmental pollution.

! Do not use hand washing detergents because these

create too much foam.

Open the detergent di-

spenser drawer and pour

in the detergent or washing

additive, as follows.

Compartment 1: Pre-wash detergent (powder)

Before pouring in the detergent, make sure that extra com-

partment 4 has been removed.

compartment 2: Detergent for the wash cycle

(powder or liquid)

Liquid detergent should only be poured in immediately

prior to the start of the wash cycle.

compartment 3: Additives (fabric softeners, etc.)

The fabric softener should not overflow the grid.

extra compartment 4: Bleach

Bleach cycle

! Traditional bleach should be used on sturdy white fa-

brics, and delicate bleach for coloured fabrics, synthetics

and for wool.

This option is particularly

useful for the removal of

stubborn stains. Place extra

compartment 4 (supplied)

into compartment 1.

When pouring in the

bleach, be careful not to

exceed the “max” level

marked on the central pivot

(see figure).

To run the bleach cycle on

its own, pour the bleach into extra compartment 4, set the

“Rinse” programme and activate the “Stain removal”

option.

To bleach during a wash cycle, pour in the detergent and

any fabric softener you wish to use, set the desired wash

cycle and enable the “Stain removal” option.

The use of extra compartment 4 excludes the “Pre-wash”

option.

Preparing the laundry

• Divide the laundry according to:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from whites.

• Empty all garment pockets and check the buttons.

• Do not exceed the listed values, which refer to the weight

of the laundry when dry:

Durable fabrics: max. 6 kg

Synthetic fabrics: max. 2,5 kg

Delicate fabrics: max. 2 kg

Wool: max. 1,5 kg

Silk: max. 1 kg

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1200 g

1 towel 150-250 g

Garments requiring special care

Wool: all wool garments can be washed using programme

7, even those carrying the “hand-wash only” label. For

best results, use special detergents and do not exceed 1,5

kg of laundry.

Silk: use special wash cycle 8 to wash all silk garments.

We recommend the use of special detergent which has

been designed to wash delicate clothes.

Curtains: fold curtains and place them in a pillow case or

mesh bag. Use wash cycle 8.

Jeans: Turn garments inside-out before washing and use

a liquid detergent. Use programme 9.

Load balancing system

Before every spin cycle, to avoid excessive vibrations and

to distribute the load in a uniform manner, the drum rotates

continuously at a speed which is slightly greater than the

washing rotation speed. If, after several attempts, the load

is not balanced correctly, the machine spins at a reduced

spin speed. If the load is excessively unbalanced, the

washing machine performs the distribution process instead

of spinning. To encourage improved load distribution and

balance, we recommend small and large garments are

mixed in the load.

Precautions and tips

! This washing machine was designed and constructed in

accordance with international safety regulations. The fol-

lowing information is provided for safety reasons and must

therefore be read carefully.

General safety

• This appliance was designed for domestic use only.

• This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities,

or lack of experience and knowledge, unless they have been

given supervision or instruction concerning use of the applian-

ce by a person responsible for their safety. Children should be

supervised to ensure that they do not play with the appliance.

• Do not touch the machine when barefoot or with wet or

damp hands or feet.

• Do not pull on the power supply cable when unplugging

the appliance from the electricity socket. Hold the plug

and pull.

• Do not open the detergent dispenser drawer while the

machine is in operation.

• Do not touch the drained water as it may reach extreme-

ly high temperatures.

• Never force the porthole door. This could damage the

safety lock mechanism designed to prevent accidental

opening.

• If the appliance breaks down, do not under any circum-

stances access the internal mechanisms in an attempt

to repair it yourself.

• Always keep children well away from the appliance while

it is operating.

• The door can become quite hot during the wash cycle.

• If the appliance has to be moved, work in a group of two

or three people and handle it with the utmost care. Never

try to do this alone, because the appliance is very heavy.

• Before loading laundry into the washing machine, make

sure the drum is empty.

Disposal

• Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

• The European Directive 2002/96/EC on Waste Electrical

and Electronic Equipment, requires that old household

electrical appliances must not be disposed of in the

normal unsorted municipal waste stream. Old applian-

ces must be collected separately in order to optimise

the recovery and recycling of the materials they contain

and reduce the impact on human health and the envi-

ronment. The crossed out “wheeled bin” symbol on the

product reminds you of your obligation, that when you

dispose of the appliance it must be separately collected.

Consumers should contact their local authority or retailer

for information concerning the correct disposal of their

old appliance.

Care and maintenance

Cutting off the water and electricity

supplies

• Turn off the water tap after every wash cycle. This will

limit wear on the hydraulic system inside the washing

machine and help to prevent leaks.

• Unplug the washing machine when cleaning it and du-

ring all maintenance work.

Cleaning the washing machine

The outer parts and rubber components of the appliance

can be cleaned using a soft cloth soaked in lukewarm

soapy water. Do not use solvents or abrasives.

Cleaning the detergent dispenser drawer

Remove the dispenser by

raising it and pulling it out

(see figure).

Wash it under running wa-

ter; this operation should be

repeated frequently.

Caring for the door and drum of your

appliance

• Always leave the porthole door ajar in order to prevent

unpleasant odours from forming.

Cleaning the pump

The washing machine is fitted with a self-cleaning pump

which does not require any maintenance. Sometimes, small

items (such as coins or buttons) may fall into the pre-cham-

ber which protects the pump, situated in its bottom part.

! Make sure the wash cycle has finished and unplug the

appliance.

To access the pre-chamber:

1. using a screwdriver,

remove the cover panel

on the lower front part of

the washing machine (see

figure);

2. unscrew the lid by rota-

ting it anti-clockwise (see

figure): a little water may

trickle out. This is perfectly

normal;

3. clean the inside thoroughly;

4. screw the lid back on;

5. reposition the panel, making sure the hooks are securely

in place before you push it onto the appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If there are any

cracks, it should be replaced immediately: during the wash

cycles, water pressure is very strong and a cracked hose

could easily split open.

! Never use second-hand hoses.

Troubleshooting

Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure

that the problem cannot be not solved easily using the following list.

Problem:

The washing machine does not

switch on.

The wash cycle does not start.

The washing machine does not

take in water (the indicator light for

the first wash cycle stage flashes

rapidly).

The washing machine continuously

takes in and drains water.

The washing machine does not

drain or spin.

The washing machine vibrates a lot

during the spin cycle.

The washing machine leaks.

The “option” indicator lights and the

“start/pause” indicator light flash,

while one of the “phase in progress”

indicator lights and the “door lo-

cked” indicator light will remain lit in

a fixed manner.

There is too much foam.

Possible causes / Solutions:

• The appliance is not plugged into the socket fully, or is not making contact.

• There is no power in the house.

• The washing machine door is not closed properly.

• The ON/OFF button has not been pressed.

• The START/PAUSE button has not been pressed.

• The water tap has not been opened.

• A delayed start has been set (see “Personalisation”).

• The water inlet hose is not connected to the tap.

• The hose is bent.

• The water tap has not been opened.

• There is no water supply in the house.

• The pressure is too low.

• The START/PAUSE button has not been pressed.

• The drain hose is not fitted at a height between 65 and 100 cm from the floor

(see “Installation”).

• The free end of the hose is under water (see “Installation”).

• The wall drainage system is not fitted with a breather pipe.

If the problem persists even after these checks, turn off the water tap, switch

the appliance off and contact the Assistance Service. If the dwelling is on one of

the upper floors of a building, there may be problems relating to water drainage,

causing the washing machine to fill with water and drain continuously. Special

anti-draining valves are available in shops and help to avoid this inconvenience.

• The wash cycle does not include draining: some wash cycles require the drain

phase to be started manually.

• The drain hose is bent (see “Installation”).

• The drainage duct is clogged.

• The drum was not unlocked correctly during installation (see “Installation”).

• The washing machine is not level (see “Installation”).

• The washing machine is trapped between cabinets and walls (see “Installation”).

• The water inlet hose is not screwed on properly (see “Installation”).

• The detergent dispenser drawer is blocked (for cleaning instructions, see “Care

and maintenance”).

• The drain hose is not fixed properly (see “Installation”).

• Switch off the machine and unplug it, wait for approximately 1 minute and then

switch it back on again.

If the problem persists, contact the Technical Assistance Service.

• The detergent is not suitable for machine washing (it should display the text

“for washing machines” or “hand and machine wash”, or the like).

• Too much detergent was used.

Service

Before calling for Assistance:

• Check whether you can solve the problem alone (see “Troubleshooting”);

• Restart the programme to check whether the problem has been solved;

• If this is not the case, contact an authorised Technical Assistance Centre using the telephone number provided on the

guarantee certificate.

! Always request the assistance of authorised technicians.

Have the following information to hand:

• the type of problem;

• the appliance model (Mod.);

• the serial number (S/N).

This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the

front of the appliance by opening the door.

Español

Sumario

Instalación, 14-15

Desembalaje y nivelación

Conexiones hidráulicas y eléctricas

Primer ciclo de lavado

Datos técnicos

Descripción de la lavadora y comienzo

de un programa, 16-17

Panel de control

Pilotos

Poner en marcha un programa

Programas, 18

Tabla de programas

Personalizaciones, 19

Seleccionar la temperatura

Seleccionar el centrifugado

Funciones

Detergentes y ropa, 20

Contenedor de detergentes

Ciclo de blanqueo

Preparar la ropa

Prendas especiales

Sistema de equilibrado de la carga

Precauciones y consejos, 21

Seguridad general

Eliminaciones

Mantenimiento y cuidados, 22

Interrumpir el agua y la corriente eléctrica

Limpiar la lavadora

Limpiar el contenedor de detergentes

Cuidar la puerta y el cesto

Limpiar la bomba

Controlar el tubo de alimentación de agua

Anomalías y soluciones, 23

Asistencia, 24

IWC 6105

Manual de instrucciones

LAVADORA

Instalación

! Es importante conservar este manual para poder consul-

tarlo en cualquier momento. En caso de venta, de cesión o

de traslado, verifique que permanezca junto con la lava-

dora para informar al nuevo propietario sobre el funciona-

miento y brindar las correspondientes advertencias.

! Lea atentamente las instrucciones: ellas contienen

importante información sobre la instalación, el uso y la

seguridad.

Desembalaje y nivelación

Desembalaje

1. Desembale la lavadora.

2. Controle que la lavadora no haya sufrido daños durante

el transporte. Si estuviera dañada no la conecte y llame al

revendedor.

3. Quite los 4 tornillos de

protección para el transpor-

te y la arandela de goma

con el correspondiente

distanciador ubicados en

la parte posterior (ver la

figura).

4. Cubra los orificios con los tapones de plástico sumini-

strados con el aparato.

5. Conserve todas las piezas: cuando la lavadora deba ser

transportada nuevamente, deberán volver a colocarse.

! Los embalajes no son juguetes para los niños.

Nivelación

1. Instale la lavadora sobre un piso plano y rígido, sin apo-

yarla en las paredes, muebles ni en ningún otro aparato.

2. Si el piso no está perfec-

tamente horizontal, com-

pense las irregularidades

desenroscando o enro-

scando las patas delanteras

(ver la figura); el ángulo de

inclinación medido sobre

la superficie de trabajo, no

debe superar los 2º.

Una cuidadosa nivelación

brinda estabilidad a la

máquina y evita vibraciones, ruidos y desplazamientos du-

rante el funcionamiento. Cuando se instala sobre moque-

tas o alfombras, regule los pies para conservar debajo de

la lavadora un espacio suficiente para la ventilación.

Conexiones hidráulicas y eléctricas

Conexión del tubo de alimentación de agua

1. Conectar el tubo de tubo

enroscándolo a un grifo de

agua fría con la boca rosca-

da de 3/4 gas (ver la figura).

Antes de conectarlo, haga

correr el agua hasta que

esté límpida.

2. Conecte el tubo de

alimentación a la lavadora

enroscándolo en la toma

de agua correspondiente

ubicada en la parte poste-

rior derecha (arriba) (ver la

figura).

3. Controle que en el tubo no hayan pliegues ni estrangu-

laciones.

! La presión de agua del grifo debe estar comprendida

dentro de los valores contenidos en la tabla de Datos

técnicos (ver la página correspondiente).

! Si la longitud del tubo de alimentación no es la suficiente,

diríjase a un negocio especializado o a un técnico autori-

zado.

! No utilice nunca tubos ya usados.

! Utilice los suministrados con la máquina.

65 - 100 cm

Conexión del tubo de descarga

Conecte el tubo de de-

scarga, sin plegarlo, a una

tubería de descarga o a una

descarga de pared colo-

cadas a una altura del piso

entre 65 y 100 cm;

o apóyelo en el borde

de un lavamanos o de

una bañera, uniendo la

guía suministrada con el

aparato, al grifo (ver la

figura). El extremo libre del

tubo de descarga no debe

permanecer sumergido en

el agua.

! No se aconseja utilizar tubos de prolongación, si fuera in-

dispensable hacerlo, la prolongación debe tener el mismo

diámetro del tubo original y no superar los 150 cm.

Conexión eléctrica

Antes de enchufar el aparato, verifique que:

• la toma tenga la conexión a tierra y haya sido hecha

según las normas legales;

• la toma sea capaz de soportar la carga máxima de

potencia de la máquina indicada en la tabla de Datos

técnicos (ver al costado);

• la tensión de alimentación esté comprendida dentro de

los valores indicados en la tabla de Datos técnicos (ver

al costado);

• la toma sea compatible con el enchufe de la lavadora. Si

no es así, sustituya la toma o el enchufe.

! La lavadora no debe ser instalada al aire libre, ni siquiera

si el lugar está reparado, ya que es muy peligroso dejarla

expuesta a la lluvia o a las tormentas.

! Una vez instalada la lavadora, la toma de corriente debe

ser fácilmente accesible.

! No utilice prolongaciones ni conexiones múltiples.

! El cable no debe estar plegado ni sufrir compresiones.

! El cable de alimentación debe ser sustituido sólo por

técnicos autorizados.

¡Atención! La empresa fabricante declina toda responsabi-

lidad en caso de que estas normas no sean respetadas.

Primer ciclo de lavado

Después de la instalación y antes del uso, realice un ciclo

de lavado con detergente y sin ropa, seleccionando el

programa 2.

Datos técnicos

Modelo

IWC 6105

Dimensiones

ancho 59,5 cm.

altura 85 cm.

profundidad 53,5 cm.

Capacidad

de 1 a 6 kg.

Conexiones

eléctricas

ver la placa de características técnicas

aplicada en la máquina

Conexiones

hídricas

presión máxima 1 MPa (10 bar)

presión mínima 0,05 MPa (0,5 bar)

capacidad del cesto 52 litros

Velocidad de

centrifugado

máxima 1000 r.p.m.

Programas de

prueba según

la directiva

2010/1061

Programa 2: temperatura 60°C y 40°C.

Esta máquina cumple con lo establecido

por las siguientes Directivas de la Comu-

nidad:

- 2004/108/CE (Compatibilidad Electro-

magnética)

- 2002/96/CE

- 2006/95/CE (Baja Tensión)

Contenedor de detergentes: para cargar detergentes y

aditivos (ver “Detergentes y ropa”).

Botón de ENCENDIDO/APAGADO: para encender y

apagar la lavadora.

Mando de PROGRAMAS: para elegir los programas. Duran-

te el funcionamiento del programa el mando no se mueve.

Botones con pilotos de FUNCIÓN: para seleccionar las

funciones disponibles. El piloto correspondiente a la función

seleccionada permanecerá encendido.

Mando de CENTRIFUGADO: para seleccionar el centrifu-

gado o excluirlo (ver “Personalizaciones”).

Mando de TEMPERATURA: para seleccionar la temperatura

o el lavado en frío (ver “Personalizaciones”).

Pilotos DE AVANCE DEL CICLO/COMIENZO RETRA-

SADO: para seguir el estado de avance del programa de

lavado. El piloto encendido indica la fase en curso.

Si se seleccionó la función “Comienzo retrasado”, indicarán

el tiempo que falta para la puesta en marcha del programa

(ver la página correspondiente).

Piloto PUERTA BLOQUEADA: para saber si la puerta se

puede abrir (ver la página correspondiente).

Botón con piloto PUESTA EN MARCHA/PAUSA: se

utiliza para poner en marcha los programas o interrumpirlos

momentáneamente.

Nota: Presione este botón para poner en pausa el lavado

en curso, el piloto correspondiente centelleará con color

anaranjado mientras que el de la fase en curso permanecerá

encendido en forma fija. Si el piloto PUERTA BLOQUEADA

está apagado, se podrá abrir la puerta.

Para que el lavado se reanude a partir del momento en el cual

fue interrumpido, presione nuevamente este botón.

Modalidad de stand by

Esta lavasecadora está en conformidad con las nuevas

normativas vinculadas al ahorro energético. Está dotada

de un sistema de auto-apagado (stand by) que, en caso de

no funcionamiento, se activa pasados aproximadamente

30 minutos. Presionar brevemente el botón ENCENDIDO/

APAGADO y esperar que la máquina se active.

Descripción de la lavadora y

comienzo de un programa

Piloto PUERTA

BLOQUEADA

Botón con piloto

PUESTA EN

MARCHA/

PAUSA

Panel de control

Contenedor de detergentes

Botón de

ENCENDIDO/

APAGADO

Mando de

PROGRAMAS

Botones con pilotos

FUNCIÓN

Mando de

TEMPERATURA

Mando de

CENTRIFUGADO

Pilotos DE AVANCE DEL

CICLO/COMIENZO

RETRASADO

Pilotos

Los pilotos suministran información importante.

He aquí lo que nos dicen:

Comienzo retrasado

Si se ha activado la función “Comienzo retrasado” (ver “Per-

sonalizaciones”), después de haber puesto en marcha el

programa, comenzará a centellear el piloto correspondien-

te al retraso seleccionado:

Con el transcurrir del tiempo se visualizará el retraso resi-

dual con el centelleo de la luz testigo correspondiente:

Una vez transcurrido el tiempo de retraso seleccionado,

comenzará el programa.

Pilotos fase en curso

Una vez seleccionado y puesto en marcha el ciclo de

lavado deseado, las luces testigo se encenderán progresi-

vamente para indicar su estado de avance:

Botones de función y pilotos correspondientes

Seleccionando una función, el piloto correspondiente se

iluminará. Si la función seleccionada no es compatible con

el programa elegido, el piloto correspondiente centelleará y

la función no se activará. Si la función elegida no es com-

patible con otra seleccionada precedentemente, el piloto

correspondiente a la primera función seleccionada centel-

leará y se activará sólo la segunda, el piloto de la función

activada se iluminará.

Piloto puerta bloqueada

El piloto encendido indica que la puerta está bloqueada

impidiendo su apertura; para poder abrir la puerta es ne-

cesario que dicho piloto esté apagado (espere 3 minutos

aproximadamente). Para abrir la puerta mientras un ciclo

está en curso, presione el botón PUESTA EN MARCHA/

PAUSA; si el piloto PUERTA BLOQUEADA está apagado,

será posible abrir la puerta.

Poner en marcha un programa

1. Encienda la lavadora presionando el botón ENCENDIDO/APAGADO. Todos los pilotos se encenderán durante algunos

segundos, luego se apagarán y se deberá pulsar el piloto PUESTA EN MARCHA/PAUSA.

2. Cargue la ropa y cierre la puerta.

3. Seleccione el programa deseado con el mando de PROGRAMAS.

4. Fije la temperatura de lavado (ver “Personalizaciones”).

5. Fije la velocidad de centrifugado (ver “Personalizaciones”).

6. Vierta detergente y aditivos (ver “Detergentes y ropa”).

7. Seleccione las funciones deseadas.

8. Ponga en marcha el programa presionando el botón PUESTA EN MARCHA/PAUSA y el piloto correspondiente perma-

necerá encendido, fijo y de color verde. Para anular el ciclo seleccionado ponga en pausa la máquina presionando el botón

PUESTA EN MARCHA/PAUSA y elija un nuevo ciclo.

9. Al final del programa se iluminará el piloto . Cuando el piloto PUERTA BLOQUEADA se apague, será posible abrir la

puerta. Extraiga la ropa y deje la puerta semicerrada para permitir que el cesto se seque.

Apague la lavadora presionando el botón ENCENDIDO/APAGADO.

Lavado

Aclarado

Centrifugado

Descarga

Fin del Lavado

Programas particulares

Express (programa 10) fue estudiado para lavar prendas ligeramente sucias y en poco tiempo: dura sólo 15 minutos

y de esa manera permite ahorrar energía y tiempo. Seleccionando el programa (10 a 30ºC) es posible lavar conjunta-

mente tejidos de distinto tipo (excluidas lana y seda), con una carga máxima de 1,5 kg.

Sport Intensive (programa 11) ha sido estudiado para lavar tejidos usados en prendas deportivas (chándales, pantalo-

nes cortos, etc.) muy sucios; para obtener los mejores resultados es aconsejable no superar la carga máxima indicada

en la “Tabla de programas”.

Sport Light (programa 12) ha sido estudiado para lavar tejidos usados en prendas deportivas (chándales, pantalones

cortos, etc.) poco sucios; para obtener los mejores resultados es aconsejable no superar la carga máxima indicada en

la “Tabla de programas”. Se recomienda utilizar detergente líquido y la dosis correspondiente a la media carga.

Sport Shoes (programa 13) ha sido estudiado para lavar calzado deportivo; para obtener los mejores resultados no

lave más de 2 pares a la vez.

Programas

Tabla de programas

Programas

Descripción del Programa

Temp.

max.

(°C)

Velocidad

máx.

(r.p.m.)

Detergentes

Carga máx.

(Kg.)

Duración

del ciclo

Prela-

vado

Lava-

Blan-

quea-

dor

Sua-

vi-

zante

Nor-

mal

Eco

Time

Nor-

mal

Eco

Time

Diario (programas para todos los días)

Prelavado Algodón: blancos sumamente sucios.

90° 1000

 



6 - 145 -

Algodón: blancos sumamente sucios.

90° 1000 -

  

6 - 125 -

Algodón (1-2): blancos y colores resistentes muy sucios.

60° 1000 -

  

6 - 190 -

Algodón (2): blancos y colores delicados poco sucios.

40° 1000 -

  

6 - 185 -

Algodón: blancos sumamente sucios.

60° 1000 -

  

6 3,5 120 85

Algodón de color (3): blancos poco sucios y colores delicados.

40° 1000 -

  

6 3,5 85 60

Sintético: colores resistentes muy sucios.

60° 800 -

  

2,5 2 110 75

Sintético (4): colores resistentes muy sucios.

40° 800 -

  

2,5 2 95 70

Sintético: colores delicados poco sucios.

40° 800 -

  

2,5 2 70 50

Programas Especiales

Lana: para lana, cachemira, etc.

40° 800 -



1,5 - 70 -

Seda/Cortinas: para prendas de seda, viscosa, lencería.

30° 0 -



1 - 55 -

9 Jeans

40° 800 -



3 - 70 -

Express: para refrescar rápidamente prendas poco sucias (no se

aconseja utilizarlo para lana, seda y prendas para lavar a mano).

30° 800 -



1,5 - 15 -

Sport

11 Sport Intensive

30° 600 -



3 -

85 -

12 Sport Light

30° 600 -



3 -

60 -

13 Sport Shoes

30° 600 -



Max. 2

pares

- 60 -

Programas Parciales

Aclarado

- 1000 - -

 

6 - 40 -

Centrifugado

- 1000 - - - -

6 - 15 -

Descarga

- 0 - - - -

6 - 2 -

La duración del ciclo que se indica en el visor o en el manual es una estimación calculada en base a condiciones estándar. El tiempo efectivo puede

variar en función de numerosos factores como la temperatura y la presión del agua de entrada, la temperatura ambiente, la cantidad de detergente,

la cantidad y el tipo de carga, el equilibrado de la carga y las opciones adicionales seleccionadas.

Para todos los Test Institutes:

1) Programa de control según la norma 2010/1061: seleccione el programa 2 con una temperatura de 60ºC y 40°C.

2) Programa algodón largo: seleccione el programa 2 con una temperatura de 40ºC.

3) Programa algodón corto: seleccione el programa 4 con una temperatura de 40ºC.

4) Programa Sintético de largo: seleccione el programa 5 con una temperatura de 40ºC.

Seleccionar la temperatura

Girando el mando de la TEMPERATURA se selecciona la temperatura de lavado (ver la Tabla de programas).

La temperatura se puede disminuir hasta el lavado en frío ( ).

La máquina impedirá automáticamente seleccionar una temperatura mayor que la máxima prevista para cada programa.

Seleccionar el centrifugado

Girando el mando de CENTRIFUGADO se selecciona la velocidad de centrifugado del programa seleccionado.

Las velocidades máximas previstas para los programas son:

Programas Velocidad máxima

Algodón 1000 r.p.m.

Sintéticos 800 r.p.m.

Lana 800 r.p.m.

Seda sólo descarga

Se puede disminuir la velocidad de centrifugado o excluirlo seleccionando el símbolo .

La máquina impedirá automáticamente efectuar un centrifugado a una velocidad mayor que la máxima prevista para cada

programa.

Funciones

Las distintas funciones de lavado previstas por la lavadora permiten obtener la limpieza y el blanco deseados.

Para activar las funciones:

1. presione el botón correspondiente a la función deseada;

2. el encendido del piloto correspondiente indica que la función está activa.

Nota: El centelleo rápido del piloto indica que la función correspondiente no se puede seleccionar para el programa elegido.

Seleccionando esta opción, se optimizan el movimiento mecánico, la temperatura y el agua para una carga reducida de

prendas de algodón y sintéticas poco sucias (ver la “Tabla de programas”).

Con “ ” se puede lavar en un tiempo menor, ahorrando agua y energía. Se aconseja utilizar una dosis de detergente

líquido adecuada a la cantidad de carga.

! No se puede activar con los programas 1, 2, 7, 8, 9, 10, 11, 12, 13, , , .

Antimancha

Ciclo de blanqueo adecuado para eliminar las manchas más resistentes. Recuerde verter el blanqueador en la cubeta adicio-

nal 4 (ver “Ciclo de blanqueo”).

! No se puede activar con los programas 1, 7, 8, 9, 10, 11, 12, 13, , .

Aclarado extra

Al elegir esta función aumentará la eficacia del aclarado y se asegurará la máxima eliminación del detergente. Es útil para

pieles particularmente sensibles.

! No se puede activar con los programas 10, , .

Comienzo retrasado

Retrasa la puesta en marcha de la máquina hasta 12 horas.

Presione varias veces el botón hasta hacer encender la luz testigo correspondiente al retraso deseado. La quinta vez que se

presione el botón, la función se desactivará.

Nota: Una vez presionado el botón PUESTA EN MARCHA/PAUSA, se puede modificar el valor del retraso sólo disminuyéndolo

hasta que se ponga en marcha el programa seleccionado.

! Se puede utilizar en todos los programas.

Personalizaciones

Detergentes y ropa

Contenedor de detergentes

El buen resultado del lavado depende también de la cor-

recta dosificación del detergente: si se excede la cantidad,

no se lava de manera más eficaz, sino que se contribuye a

encostrar las partes internas de la lavadora y a contaminar

el medio ambiente.

! No use detergentes para el lavado a mano porque pro-

ducen demasiada espuma.

Extraiga el contenedor de

detergentes e introduzca el

detergente o el aditivo de la

siguiente manera:

cubeta 1: Detergente para prelavado (en polvo)

Antes de verter el detergente, verifique que no esté colo-

cada la cubeta adicional 4.

cubeta 2: Detergente para lavado (en polvo o

líquido)

El detergente líquido se debe verter sólo antes de la pue-

sta en marcha.

cubeta 3: Aditivos (suavizante, etc.)

El suavizante no se debe volcar fuera de la rejilla.

cubeta adicional 4: Blanqueador

Ciclo de blanqueo

! El blanqueador tradicional debe utilizarse para los teji-

dos resistentes blancos, mientras que el delicado debe

utilizarse para la lana y los tejidos coloreados y sintéticos.

Introduzca la cubeta adicio-

nal 4 suministrada con el

aparato, en la cubeta 1.

Al verter el blanqueador

no debe superar el nivel

“máx.” indicado en el per-

no central (véase la figura).

Para realizar sólo el blanqueo, vierta el blanqueador en la

cubeta adicional 4, seleccione el programa “Aclarado” y

active la función “Antimancha” .

Para blanquear durante el lavado, vierta el detergente y

los aditivos, seleccione el programa deseado y active la

función “Antimancha” .

El uso de la cubeta adicional 4 excluye el prelavado.

Preparar la ropa

• Subdivida la ropa según:

- el tipo de tejido / el símbolo en la etiqueta.

- los colores: separe las prendas de color y las blancas.

• Vacíe los bolsillos y controle los botones.

• No supere los valores indicados, referidos al peso de la

ropa seca:

Tejidos resistentes: max 6 kg.

Tejidos sintéticos: max 2,5 kg.

Tejidos delicados: max 2 kg.

Lana: max 1,5 kg.

Seda: max 1 kg.

¿Cuánto pesa la ropa?

1 sábana 400/500 g

1 funda 150/200 g

1 mantel 400/500 g

1 albornoz 900/1200 g

1 toalla 150/250 g

Prendas especiales

Lana: con el programa 7 es posible lavar en la lavadora

todas las prendas de lana, aún las que contienen la eti-

queta “sólo lavado a mano” Para obtener los mejores

resultados utilice un detergente específico y no supere

1,5 Kg. de ropa.

Seda: utilice el programa correspondiente 8 para lavar

todas las prendas de seda. Se aconseja el uso de un

detergente específico para prendas delicadas.

Cortinas: pliéguelas y colóquelas dentro de una funda o

de una bolsa de red. Utilice el programa 8.

Jeans: vuelva del revés las prendas antes del lavado y

utilice un detergente líquido. Utilice el programa 9.

Sistema de equilibrado de la carga

Antes de cada centrifugado, para evitar vibraciones exce-

sivas y para distribuir la carga de modo uniforme, el cesto

realiza rotaciones a una velocidad ligeramente superior a la

del lavado. Si después de varios intentos, la carga todavía

no está correctamente equilibrada, la máquina realiza el

centrifugado a una velocidad inferior a la prevista. Cuando

existe un excesivo desequilibrio, la lavadora realiza la

distribución antes que el centrifugado. Para obtener una

mejor distribución de la carga y su correcto equilibrado, se

aconseja mezclar prendas grandes y pequeñas.

La pagina sta caricando ...

Indesit IWC 6105 (EU) Guida utente

Marca: Indesit

Modello: IWC 6105 (EU)

Categoria: Lavatrici

Tipo: Guida utente

Scarica il pdf

rapporto

in altre lingue

English: Indesit IWC 6105 (EU) User guide
español: Indesit IWC 6105 (EU) Guía del usuario
português: Indesit IWC 6105 (EU) Guia de usuario
polski: Indesit IWC 6105 (EU) instrukcja