Haier HAFRSJ63MC Manuale utente

HAIER

HAFRSJ64MC

ENGLISH

Instruction Manual For Induction Hob

ITALIANO

Manuale di istruzioni per piano di cottura ad induzione

POLSKI

Instrukcja obsługi płyty indukcyjnej

FRANÇAIS

Manuel d’utilisation de la table de cuisson à induction

ESPAÑOL

Manual de instrucciones de la encimera de inducción

DEUTSCH

Bedienungsanleitung für Induktionskochfeld

Návod na obsluhu indukčnej varnej dosky

SLOVENČINA

Návod k obsluze indukční varné desky

ČEŠTINA

Manual de instruções para placa de indução

PORTUGUÊS

Ръководство за употреба на индукционен плот

БЪЛГАРСКИ

By placing CE mark on this product, we are conﬁrming com-

pliance to all relevant European safety, health and environmental

requirements which are applicable in legisla�on for this product.

As applicable

EN-2

ENGLISH

EN-3

EN-4

ENGLISH

Haier

EN-5

1. Max. 2000/3000 W zone

2. Max. 2000/3000 W zone

3. Max. 1800/2300 W zone

4. Max. 1800/2300 W zone

5. Max. 3000/4000 W zone

6. Glass plate

7. Control panel

1. Heating zone power controls

2. "Cook with me Function control"

3. Timer control

4. Flexible Area control

6. ON/OFF control

Keylock .5

1

2

3

4

5

6

7

1

2

3

4

5

6

EN-6

ENGLISH

Touch Controls

•

The controls respond to touch, so you don’t need to apply any pressure.

•

Use the ball of your finger, not its tip.

•

You will hear a beep each time a touch is registered.

•

Make sure the controls are always clean, dry, and that there is no object (e.g. a utensil or a cloth) covering them.

Even a thin film of water may make the controls difficult to operate.

Choosing the right Cookware

•

Only use cookware with a base suitable for induction cooking.

Look for the induction symbol on the packaging or on the bottom

of the pan.

• You can check whether your cookware is suitable by carrying out a magnet test.

Move a magnet towards the base of the pan. If it is attracted, the pan is suitable

for induction.

• If you do not have a magnet:

1. Put some water in the pan you want to check.

2. If does not flash in the display and the water is heating, the pan is suitable.

• Cookware made from the following materials is not suitable: pure stainless steel, aluminium or copper

without a magnetic base, glass, wood, porcelain, ceramic, and earthenware.

Do not use cookware with jagged edges or a curved base.

Make sure that the base of your pan is smooth, sits flat against the glass, and is the same size as the cooking zone.

Use pans whose diameter is as large as the graphic of the zone selected. Using a pot a slightly wider energy will be

used at its maximum efficiency. If you use smaller pot efficiency could be less than expected. Pot less than 140 mm

could be undetected by the hob. Always centre your pan on the cooking zone.

Always lift pans off the Induction hob – do not slide, or they may scratch the glass.

EN-7

How to use

Start cooking

Touch the ON/OFF control for three seconds.

After power on, the

buzzer beeps once, all displays show “–” or “– –”, indicating that the

induction hob has entered the state of standby mode.

Place a suitable pan on the cooking zone that you wish to use.

• Make sure the bottom of the pan and the surface of the cooking

zone are clean and dry.

Touching the heating zone slider control ,

and a indicator next to the

key will flash.

Select a heat setting by touching the slider control

• If you don’t choose a heat setting within 1 minute, the Induction

hob will automatically switch off. You will need to start again at step 1.

• You can modify the heat setting at any time during cooking.

If the display flashes alternately with the heat setting

This means that:

• you have not placed a pan on the correct cooking zone or,

• the pan you’re using is not suitable for induction cooking or,

• the pan is too small or not properly centered on the cooking zone.

EN-8

ENGLISH

No heating takes place unless there is a suitable pan on the cooking zone.

The display will automatically disappear after 1 minute if no suitable pan is placed on it.

power up

power down

Finish cooking

Touching the heating zone selection control that you wish to

switch off.

the display shows “0”.

Turn the whole cooktop off by touching the ON/OFF control.

Beware of hot surfaces

H will show which cooking zone is hot to touch. It will

disappear when the surface has cooled down to a safe

temperature. It can also be used as an energy saving function

if you want to heat further pans, use the hotplate that is still

hot.

Using the Boost function

Activate the boost function

Touching the heating zone slider control

Touching the slider to “B”. Make sure the display shows “b”.

Cancel the Boost function

Touching the heating zone slider control that you wish to cancel

the boost function.

the display shows “0”.

Turn the cooking zone off by touching the slider to “ 0 ”. Make sure

Turn the cooking zone off by touching the slider to “0”. Make sure

EN-9

• The function can work in any cooking zone.

• The cooking zone returns to its original setting after 5 minutes.

• If the original heat setting equals 0, it will return to 9 after 5 minutes.

Flexible Area

• This area can be used as a single zone or as two different zones, accordingly to the cooking needs anytime.

• Flexible area is made of two independent inductors that can be controlled separately. When working as a single zone,

the part that is not covered by cookware is automatically switched off after one minute.

• To grant a correct pan detection and a even heat distribution, the cookware should be correctly placed:

- In the front or rear side of the flexible zone when the cookware is smaller than 22 cm

- Anywhere with bigger cookware

As big zone

To activate the flexible area as a single big zone, simply press the Flexible

Area control.

The power setting works as any other normal area.

If the pot is moved from the front to the rear part (or vice versa), the flexible area detects automatically the new position,

keeping the same power.

To add a further pot, press again the dedicated keys, in order to detect the cookware.

As two independent zones

To use the flexible area as two different zones with different power settings, press the Flexible Area control.

• This area can set the power according to the position of the pot.

• If the pot is on the bottom of flexible area, the power is set to Level 1.

• If the pot is on the top of flexible area, the power is set to Level 9.

for 2 second

Move the position of the pot, the power will change automatically

Press the Flexible Area control to turn off the cooking zone.

French Plaque

• If the pot is on the middle of flexible area, the power is set to Level 6.

French Plaque

To activate the French Plaque area, simply press the Flexible Area control

Cancel French Plaque

EN-10

ENGLISH

Locking the Controls

•

You can lock the controls to prevent unintended use (for example children accidentally turning the cooking zones

on).

•

When the controls are locked, all the controls except the ON/OFF control are disabled.

When the hob is in the lock mode, all the controls are disable except the ON/OFF

,

you can always turn the induction

hob off with the ON/OFF control in an emergency, but you shall unlock the hob first in the next operation.

Pause Mode

•

You can pause the heating instead of shutting the hob off.

•

When entering the Pause mode, all the controls except the ON/OFF control are disabled.

To enter pause mode

Short touch the Timer “ ” and Timer ”

” at the same

time.

All the indicator will show “ 11“

To exit pause mode

Short touch the Timer “ ” and Timer ”

” at the same time.

When the hob is in the pause mode, all the controls are disable except the ON/OFF

,

you can always turn the

induction hob off with the ON/OFF control in an emergency. The hob will shut down after 10min if you don’t exit the

pause mode.

Power Management Function

•

it is possible to set a maximum power absorption level for the induction hob, choosing up to different power

ranges.

•

induction hobs are able to limit themselves automatically in order to work at lower power level, to avoid the risk of

overloading.

The timer indicator will show “ Lo ”

To lock the controls

To unlock the controls

Touch and hold the lock control for a

while.

Touch and hold the lock control for a while.

EN-11

To enter Power Management Function

The timer indicator will show “ P5“ which means power

To switch to another level

or

There are 5 power levels, from “P1” to “p5”. The timer

indicator will show one of them.

“P1” : the maximum power is 2.5Kw.

“P2” : the maximum power is 3.5Kw.

“P3” : the maximum power is 4.5Kw.

“P4” : the maximum power is 5.5Kw.

Confirmation and Exit Power Management Function

” for confirmation.

Then the hob will be turned off.

Timer control

You can use the timer in two different ways:

•

You can use it as a minute minder. In this case, the timer will not turn any cooking zone off when the set time is

up.

•

You can set it to turn one or more cooking zones off after the set time is up.

The timer of maximum is 99min.

Turn on the hob, then Press at the same time the

press +/- of the timer

and Timer ”

level 5 The default mode is on max power of the hob.

“P5” : the maximum power is max power of the hob.

Press at the same time key lock

key lock and ” .Timer

”

EN-12

ENGLISH

a) Using the Timer as a Minute Minder

If you are not selecting any cooking zone

Make sure the cooktop is turned on.

Note: you can use the minute minder even if you’re not selecting any

cooking zone.

Touch “+” the controls of the timer. The minder

indicator will start flashing and “10” will show

in the timer display.

Set the time by touching the “-” or “+” control

of the timer

Hint: Touch the “-” or “+” control of the timer

once to decrease or increase by 1 minute.

Touch and hold the “-” or “+” control of the timer to decrease or

increase by 10 minutes.

When the time is set, it will begin to count down

immediately. The display will show the remaining

time and the timer indicator will flash for 5 seconds.

Buzzer will beep for 30 seconds and the timer

indicator shows “- - “ when the setting time finished.

b) Setting the timer to turn one or more cooking zones off

Set one zone

Touching the heating zone slider control

Set the time by touching the or control of the timer

Hint: Touch the “-“ or “+” control of the timer

once will decrease or increase by 1 minute.

Touch and hold the ”-“ or “+”control of the timer

will decrease or increase by 10 minutes.

When the time is set, it will begin to count down immediately. The display

will show the remaining time and the timer indicator flash for 5 seconds.

NOTE: The red dot next to power level indicator will illuminate

indicating that zone is selected.

EN-13

When cooking timer expires, the corresponding cooking zone will be

switched off automatically.

Other cooking zone will keep operating if they are turned on previously.

set more zones:

The steps for setting more zones are similar to the steps of setting one zone;

When you set the time for several cooking zones simultaneously, decimal dots of the relevant cooking zones are on.

The minute display shows the min. timer. The dot of the corresponding zone flashes.

The shown as below:

(set to 15 minutes)

(set to 45 minutes)

Once the countdown timer expires, the corresponding zone will

switch off. Then it will show the new min. timer and the dot of

corresponding zone will flash.

The shown as right:

(set to 30 minutes)

Touch the heating zone selection control, the corresponding timer will be shown in the timer indicator.

c) Cancel the timer

Touching the heating zone slider control that you want to cancel

the timer

Touch and hold the timer control “ - ”, the timer decreases to “00”

and the timer is cancelled.

Default working times

Auto shut down is a safety protection function for your induction hob. It shut down automatically if ever you forget to

turn off your cooking. The default working times for various power levels are shown in the below table:

Power level

1 2 3 4 5 6 7 8 9

Default working timer (hour)

8 8 8 4 4 4 2 2 2

When the pot is removed, the induction hob can stop heating immediately and the hob automatically switch off after 2

minutes.

People with a heart pace maker should consult with their doctor before using this unit.

EN-14

ENGLISH

To make the pairing between Hob and APP use the following process:

When wi-fi ON: one dot will appear on the right side of the LED

When WIFI OFF: No dot will appear.

Cook with me function

Press 4 seconds the "Cook with me" button on the hob. Once the 4 seconds have passed, the digit of the TIMER starts to blink with

PA written on it and starts the pairing process. Now follow the instructions from the App.

How to set Cook with me

If you want to get out of "Cook with me" function change the power

level of the zone.

First of all, you should download hOn App and install to your portable device. Then enroll your induction hob following the

instructions directly from the App.

Choose from the hOn App recipes menu or special programs menu.

Follow step by step the indications on the App and when you have

finished send the parameters to the hob that will cook for you.

When the hob receives the command from the app, the hob will beep

for 2 times and blink for one second to indicate that the instructions

have been received.

a. WIRELESS PARAMETERS

Technology Wi-Fi BLE NFC

Standard

IEEE 802.11b/n/g

Bluetooth v4.2, BR/EDR, BLE /

Frequency Band(s) [MHz] 2402-2480 2402-2480 /

Maximum Power [mW] 1500 1500 /

press 4 seconds

EN-15

EN-16

ENGLISH

Selection of cooking vessels

You may have a number of different cooking vessels

1. This induction hob can identify a variety of cooking vessels, which you can test by

one of the following methods:

Place the vessel on the cooking zone. If the corresponding cooking zone displays a

power level, then the vessel is suitable. If “U” flashes, then the vessel is not

suitable for use with the induction hob.

2. Hold a magnet to the vessel. If the magnet is attracted to the vessel is suitable for

use with the induction hob.

NB: The base of the vessel must contain magnetic material.

It must have flat bottom with a diameter according to the table 1 below.

3. Use only ferromagnetic cookwares made from enameled steel, cast iron or stainless

steel but compatible with induction

4. Use pans whose diameter of the ferromagnetic area (base of the pan) is in the range

of dimensions in the table below. (Table 1)

- If you use smaller pots, performance could be affected

- If you use pot with a diameter smaller than the one indicated in the table 1, pots

may not be detected

According to the dimension of the zone you can use pots of different diameters as picture

below:

Iron oil frying

Stainless steel

Iron pan

Iron kettle

Enamel

stainless steel

kettle

Enamel cooking

utesil

Iron plate

EN-17

5. If the ferromagnetic part covers only partially the base of the pan, only the

ferromagnetic area will heat up, the rest of the base may not heat up a sufficient

temperature for cooking.

6. If the ferromagnetic area is not homogeneous, but presents others material such as

aluminum this may affect the heating up and the pan detection.

If the base of the pan is similar to the pictures below the pan could be not detected.

The base diameter of induction cookware

Cooking zone

1 & 2 140

140

220

1803 & 4

Minimum Maximum

Flexi zone 220

The above may vary according to the size of the pan and the material it is made from.

220*400

The induction hob is equipped with a self diagnostic function. With this test the technician is able to check the function

of several components without disassembling or dismounting the hob from the working surface.

Troubleshooting

1) Failure code occur during customer using & Solution;

Failure code Problem Solution

Auto-Recovery

E1 Supply voltage is above the rated voltage.

Please inspect whether power supply is normal.

Power on after the power supply is normal.

E2 Supply voltage is below the rated voltage.

E3 High temperature of ceramic plate sensor . 1# Wait for the temperature of ceramic plate return

to normal.

Touch “ON/OFF” button to restart unit.

E4 High temperature of ceramic plate sensor . 2#

E5 High temperature of IGBT . 1#

Wait for the temperature of IGBT return to

normal.

Touch “ON/OFF” button to restart unit.

Check whether the fan runs smoothly;

if not , replace the fan.

E6 High temperature of IGBT. 2#

No Auto-Recovery

F3/F6

Ceramic plate temperature sensor failure- -short

circuit. (F3 for 1#,F6 for2#)

Check the connection or replace the ceramic

plate temperature sensor.

F4/F7

Ceramic plate temperature sensor failure--open

circuit. (F4 for 1#,F7 for2#)

F5/F8

Ceramic plate temperature sensor

failure—invalid . (F5 for 1#,F8 for2#)

F9/FA

Temperature sensor of the IGBT failure. short

circuit/open circuit for 1#

Replace the power board.

FC /FD

Temperature sensor of the IGBT failure. short

circuit/open circuit for 2#

EN-18

ENGLISH

The above are the judgment and inspection of common failures.

Please do not disassemble the unit by yourself to avoid any dangers and damages to the induction hob.

2) Specific Failure & Solution

Failure Problem Solution A Solution B

The LED does not

come on when unit is plugged

in.

No power supplied. Check to see if plug is

secured tightly in outlet and

that outlet is working.

The accessorial power

board and the display

board connected failure.

Check the connection.

The accessorial power

board is damaged.

Replace the accessorial

power board.

The display board is

damaged.

Replace the display board.

Some buttons can’t work, or

the LED display is not normal.

The display board is

damaged.

Replace the display board.

The Cooking Mode Indicator

comes on, but heating does

not start.

High temperature of the

hob.

Ambient temperature may be

too high. Air Intake or Air

Vent may be blocked.

There is something wrong

with the fan.

Check whether the fan runs

smoothly

if not , replace the fan.

The power board is

damaged.

Replace the power board.

Heating stops suddenly

during operation and the

display flashes “u”.

Pan Type is wrong. Use the proper pot (refer to

the instruction manual.)

Pan detection circuit

is damaged, replace

the power board.

Pot diameter is too small.

Cooker has overheated

;

Unit is overheated. Wait for

temperature to return to

normal.

Push “ON/OFF” button to

restart unit.

Heating zones of the same

side ( Such as the first and

the second zone ) would

display “u” .

The power board and the

display board connected

failure;

Check the connection.

The display board of

communicate part is

damaged.

Replace the display board.

The Main board is

damaged.

Replace the power board.

Fan motor sounds abnormal. The fan motor is damaged. Replace the fan.

EN-19

La pagina sta caricando ...

Haier HAFRSJ63MC Manuale utente

Questo manuale è adatto anche per

Haier HAFRSJ63MC Manuale utente

in altre lingue

Documenti correlati

Altri documenti