Chicago Pneumatic CP 1230 SPDR, CP 1240 SPDR Istruzioni per l'uso

Safety and operating instructions

Handheld pneumatic spike drivers

CP 1230 SPDR, CP 1240 SPDR

Prescriptions de sécurité et instructions pour

l’opérateur

Marteaux à crampons pneumatiques portatifs

Sicherheits- und Betriebsanleitung

Hand-Druckluftnagelhämmer

Instrucciones de seguridad y de funcionamiento

Håndholdte trykluftdrevne værktøjer til montering af spiger

Instruções de segurança e operação

Cravadores de espigões pneumáticos manuais

Istruzioni per la sicurezza e per l'uso

Martelli battitori pneumatici manuali

Veiligheidsvoorschriften en bedieningshandleiding

Handbediende pneumatische spijkermachines

Οδηγίες ασφάλειας και χειρισμού

Φορητά πνευματικά μηχανήματα οδήγησης βελονών

Turvallisuusohjeet ja käyttöohje

Käsikäyttöiset paineilmapiikkivasarat

Sikkerhedsinstruktioner og betjeningsvejledning

Håndholdte trykluftdrevne værktøjer til montering af spiger

Sikkerhetsinstrukser og bruksanvisning

Håndholdte pneumatiske spikerpistoler

Säkerhetsinstruktion och instruktionsbok

Handhållna tryckluftsdrivna spikhammare

www.cp.com

9800 0555 90a | Original instructions2

CP 1230 SPDR, CP 1240 SPDR

Contents

ENGLISH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

FRANÇAIS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

DEUTSCH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

ESPAÑOL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

PORTUGUÊS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

ITALIANO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

NEDERLANDS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

ΕΛΛΗΝΙΚΑ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116

SUOMI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134

DANSK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148

NORSK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164

SVENSKA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178

39800 0555 90a | Original instructions

CP 1230 SPDR, CP 1240 SPDR

ENGLISH

Contents

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

About the Safety and operating instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Safety signal words. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Personal precautions and qualifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Installation, precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Operation, precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Maintenance, precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Storage, precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Design and function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Main parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Labels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Hoses and connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Methods to prevent freezing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Connecting a water separator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Lubrication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Start and stop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Operating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

When taking a break. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Every day. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Assembly instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Periodic maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Tightening torques. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Machine data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Noise and vibration declaration statement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Noise and vibration data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

EC Declaration of Conformity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

EC Declaration of Conformity (EC Directive 2006/42/EC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

9800 0555 90a | Original instructions4

CP 1230 SPDR, CP 1240 SPDRContents

Introduction

Thank you for choosing Chicago Pneumatic brand products. For over a century, the

Chicago Pneumatic brand has represented performance and innovation in the

pneumatic tool industry.

Today the brand is found around the world on a range of pneumatic and hydraulic

tools that includes breakers, rock drills, chipping hammers, clay-diggers, picks and

busters, scabblers, pumps and a whole lot more.

The Chicago Pneumatic brand is associated with powerful and reliable products that

are easy to maintain and that give good value for the money.

For more information please visit www.cp.com

Atlas Copco Construction Tools AB

105 23 Stockholm

Sweden

About the Safety and operating

instructions

The aim of the instructions is to provide you with knowledge of how to use the

pneumatic spike driver in an efficient, safe way. The instructions also give you advice

and tell you how to perform regular maintenance on the pneumatic spike driver.

Before using the pneumatic spike driver for the first time you must read these

instructions carefully and understand all of them.

59800 0555 90a | Original instructions

Safety and operating instructionsCP 1230 SPDR, CP 1240 SPDR

Safety instructions

To reduce the risk of serious injury or death to

yourself or others, read and understand the Safety

and operating instruction before installing,

operating, repairing, maintaining, or changing

accessories on the machine.

Post this Safety and operating instruction at work

locations, provide copies to employees, and make

sure that everyone reads the Safety and operating

instruction before operating or servicing the

machine.

In addition, the operator or the operator's employer

must assess the specific risks that may be present as

a result of each use of the machine.

Safety signal words

The safety signal words Danger, Warning and

Caution have the following meanings:

Indicates a hazardous situation

which, if not avoided, will result

in death or serious injury.

DANGER

Indicates a hazardous situation

which, if not avoided, could

result in death or serious injury.

WARNING

Indicates a hazardous situation

which, if not avoided, could

result in minor or moderate

injury.

CAUTION

Personal precautions and

qualifications

Only qualified and trained persons may operate or

maintain the machine. They must be physically able

to handle the bulk, weight, and power of the tool.

Always use your common sense and good

judgement.

Personal protective equipment

Always use approved protective equipment.

Operators and all other persons in the working area

must wear protective equipment, including at a

minimum:

> Protective helmet

> Hearing protection

> Impact resistant eye protection with side

protection

> Respiratory protection when appropriate

> Protective gloves

> Proper protective boots

> Appropriate work overall or similar clothing (not

loose-fitting) that covers your arms and legs.

Drugs, alcohol or medication

WARNING Drugs, alcohol or medication

Drugs, alcohol or medication may impair your

judgment and powers of concentration. Poor

reactions and incorrect assessments can lead to

severe accidents or death.

► Never use the machine when you are tired or

under the influence of drugs, alcohol or

medication.

► No person who is under the influence of drugs,

alcohol or medication may operate the machine.

Installation, precautions

DANGER Whipping air hose

A compressed air hose that comes loose can lash

around and cause personal injury or death. To

reduce this risk:

► Check that the compressed air hose and the

connections are not damaged, replace if

necessary.

► Check that all compressed air connections are

properly attached.

► Never carry a pneumatic machine by the air hose.

► Never attempt to disconnect a compressed air

hose that is pressurized. First switch off the

compressed air at the compressor and then bleed

the machine by activating the start and stop

device.

► Do not use quick disconnect couplings at tool

inlet. Use hardened steel (or material with

comparable shock resistance) threaded hose

fittings.

► Whenever universal twist couplings (claw

couplings) are used, we recommend that lock

pins are installed and whipcheck safety cables are

used to safeguard against possible hose to tool

and hose to hose connection failure.

9800 0555 90a | Original instructions6

CP 1230 SPDR, CP 1240 SPDRSafety and operating instructions

Operation, precautions

DANGER Explosion hazard

If a spike comes into contact with explosives or

explosive gases, an explosion could occur. When

working on certain materials and when using certain

materials in machine parts, sparks and ignition can

occur. Explosions will lead to severe injuries or death.

► Never operate the machine in any explosive

environment.

► Never use the machine near flammable materials,

fumes or dust.

► Make sure that there are no undetected sources

of gas or explosives.

WARNING Unexpected movements

The spike driver is exposed to forces when in use.

The forces can cause sudden and unexpected

movement that can cause injuries. Furthermore,

losing your balance or slipping may cause injury.

► Make sure that you always keep a stable position

with your feet as far apart as your shoulder width,

and keeping a balanced body weight.

► Always inspect the equipment prior to use. Never

use the equipment if you suspect that it is

damaged.

► Make sure that the handles are clean and free of

grease and oil.

► Keep hands and feet away from the spike.

► Stand firmly and always hold on to the machine

with both hands.

► Never start the machine when it is lying on the

ground.

► Never ‘ride’ on the machine with one leg over the

handle.

► Never strike or abuse the equipment.

► Pay attention and look at what you are doing.

WARNING Dust and fume hazard

Dusts and/or fumes generated or dispersed when

using the machine may cause serious and permanent

respiratory disease, illness, or other bodily injury (for

example, silicosis or other irreversible lung disease

that can be fatal, cancer, birth defects, and/or skin

inflammation).

Some dusts and fumes created by drilling, breaking,

hammering, sawing, grinding and other construction

activities contain substances known to the State of

California and other authorities to cause respiratory

disease, cancer, birth defects, or other reproductive

harm. Some examples of such substances are:

> Crystalline silica, cement, and other masonry

products.

> Arsenic and chromium from chemically-treated

rubber.

> Lead from lead-based paints.

Dust and fumes in the air can be invisible to the

naked eye, so do not rely on eye sight to determine

if there is dust or fumes in the air.

To reduce the risk of exposure to dust and fumes,

do all of the following:

► Perform site-specific risk assessment. The risk

assessment should include dust and fumes created

by the use of the machine and the potential for

disturbing existing dust.

► Use proper engineering controls to minimize the

amount of dust and fumes in the air and to

minimize build-up on equipment, surfaces,

clothing, and body parts. Examples of controls

include: exhaust ventilation and dust collection

systems, water sprays, and wet drilling. Control

dusts and fumes at the source where possible.

Make sure that controls are properly installed,

maintained and correctly used.

► Wear, maintain and correctly use respiratory

protection as instructed by your employer and as

required by occupational health and safety

regulations. The respiratory protection must be

effective for the type of substance at issue (and if

applicable, approved by relevant governmental

authority).

► Work in a well ventilated area.

► If the machine has an exhaust, direct the exhaust

so as to reduce disturbance of dust in a dust filled

environment.

► Operate and maintain the machine as

recommended in the operating and safety

instructions

79800 0555 90a | Original instructions

Safety and operating instructionsCP 1230 SPDR, CP 1240 SPDR

► Select, maintain and replace consumables/

inserted tools/ other accessory as recommended

in the operating and safety instructions. Incorrect

selection or lack of maintenance of consumables/

inserted tools/ other accessories may cause an

unnecessary increase in dust or fumes.

► Wear washable or disposable protective clothes

at the worksite, and shower and change into clean

clothes before leaving the worksite to reduce

exposure of dust and fumes to yourself, other

persons, cars, homes, and other areas.

► Avoid eating, drinking, and using tobacco

products in areas where there is dust or fumes.

► Wash your hands and face thoroughly as soon as

possible upon leaving the exposure area, and

always before eating, drinking, using tobacco

products, or making contact with other persons.

► Comply with all applicable laws and regulations,

including occupational health and safety

regulations.

► Participate in air monitoring, medical examination

programs, and health and safety training

programs provided by your employer or trade

organizations and in accordance with

occupational health and safety regulations and

recommendations. Consult with physicians

experienced with relevant occupational medicine.

► Work with your employer and trade organization

to reduce dust and fume exposure at the worksite

and to reduce the risks. Effective health and safety

programs, policies and procedures for protecting

workers and others against harmful exposure to

dust and fumes should be established and

implemented based on advice from health and

safety experts. Consult with experts.

► Residues of hazardous substances on the machine

can be a risk. Before undertaking any maintenance

on the machine clean it thoroughly.

WARNING Projectiles

Failure of the work piece, of accessories, or even of

the machine itself may generate high velocity

projectiles. During operating, splinters or other

particles from the working material may become

projectiles and cause personal injury by striking the

operator or other persons. To reduce these risk:

► Use approved personal protective equipment and

safety helmet, including impact resistant eye

protection with side protection.

► Make sure that no unauthorised persons trespass

into the working zone.

► Keep the workplace free from foreign objects.

► Ensure that the spike is securely fixed.

WARNING Spike driving hazard

If the spike is not securely fixed into the work piece

before operating the machine, there is a risk of

personal injury.

► Always make sure to secure the spike before

operating the machine.

► Never hold or touch the spike when driving.

WARNING Slipping, tripping and

falling hazards

There is a risk of slipping or tripping or falling, for

example tripping on the hoses or on other objects.

Slipping or tripping or falling can cause injury. To

reduce this risk:

► Always make sure that no hose or other object is

in your way or in any other person's way.

► Always make sure you are in a stable position with

your feet as far apart as your shoulders width and

keeping a balanced body weight.

WARNING Motion hazards

When using the machine to perform work-related

activities, you may experience discomfort in the

hands, arms, shoulders, neck, or other parts of the

body.

► Adopt a comfortable posture whilst maintaining

secure footing and avoiding awkward

off-balanced postures.

► Changing posture during extended tasks may

help avoid discomfort and fatigue.

► In case of persistent or recurring symptoms,

consult a qualified health professional.

9800 0555 90a | Original instructions8

CP 1230 SPDR, CP 1240 SPDRSafety and operating instructions

WARNING Vibration hazards

Normal and proper use of the machine exposes the

operator to vibration. Regular and frequent exposure

to vibration may cause, contribute to, or aggravate

injury or disorders to the operator’s fingers, hands,

wrists, arms, shoulders and/or nerves and blood

supply or other body parts, including debilitating

and/or permanent injuries or disorders that may

develop gradually over periods of weeks, months,

or years. Such injuries or disorders may include

damage to the blood circulatory system, damage to

the nervous system, damage to joints, and possibly

damage to other body structures.

If numbness, persistent recurring discomfort,

burning sensation, stiffness, throbbing, tingling,

pain, clumsiness, weakened grip, whitening of the

skin, or other symptoms occur at any time, when

operating the machine or when not operating the

machine, stop operating the machine, tell your

employer and seek medical attention. Continued

use of the machine after the occurrence of any such

symptom may increase the risk of symptoms

becoming more severe and/or permanent.

Operate and maintain the machine as recommended

in these instructions, to prevent an unnecessary

increase in vibration.

The following may help to reduce exposure to

vibration for the operator:

► Let the tool do the job. Use a minimum hand grip

consistent with proper control and safe operation.

► If the machine has vibration absorbing handles,

keep them in a central position, avoid pressing

the handles into the end stops.

► When the percussion mechanism is activated, the

only body contact with the machine you should

have are your hands on the handle or handles.

Avoid any other contact, for example supporting

any part of the body against the machine or

leaning onto the machine trying to increase the

feed force. It is also important not to keep the start

and stop device engaged while extracting the tool

from the broken work surface.

► Immediately stop working if the machine

suddenly starts to vibrate strongly. Before

resuming the work, find and remove the cause of

the increased vibrations.

► Participate in health surveillance or monitoring,

medical exams and training programs offered by

your employer and when required by law.

► When working in cold conditions wear warm

clothing and keep hands warm and dry.

See the ”Noise and vibration declaration statement”

for the machine, including the declared vibration

values. This information can be found at the end of

these Safety and operating instructions.

♦

Comply with the recommended air-pressure when

operating the machine. Either higher or lower

air-pressure has the potential of resulting in higher

levels of vibration.

DANGER Electrical hazard

The machine is not electrically insulated. If the

machine comes into contact with electricity, serious

injuries or death may result.

► Never operate the machine near any electric wire

or other source of electricity.

► Make sure that there are no concealed wires or

other sources of electricity in the working area.

WARNING Concealed object hazard

During operating, concealed wires and pipes

constitute a danger that can result in serious injury.

► Check the composition of the material before

operating.

► Watch out for concealed cables and pipes for

example electricity, telephone, water, gas and

sewage lines etc.

► If the spike seems to have hit a concealed object,

switch off the machine immediately.

► Make sure that there is no danger before

continuing.

WARNING Involuntary start

Involuntary start of the machine may cause injury.

► Keep your hands away from the start and stop

device until you are ready to start the machine.

► Learn how the machine is switched off in the event

of an emergency.

► Release the start and stop device immediately in

all cases of power supply interruption.

► Before undertaking any kind of maintenance,

installation, inspection or cleaning; switch off the

air supply, bleed the machine by activating the

start and stop device and disconnect the machine

from the power source.

WARNING Noise hazard

High noise levels can cause permanent and disabling

hearing loss and other problems such as tinnitus

(ringing, buzzing, whistling or humming in the ears).

To reduce risk and prevent an unnecessary increase

in noise levels:

► Risk assessment of these hazards and

implementation of appropriate controls is

essential.

► Operate and maintain the machine as

recommended in these instructions.

► If the machine has a muffler, check that it is in

place and in good working condition.

99800 0555 90a | Original instructions

Safety and operating instructionsCP 1230 SPDR, CP 1240 SPDR

► Always use hearing protection.

Maintenance, precautions

WARNING Machine modification

Any machine modification may result in bodily

injuries to yourself or others.

► Never modify the machine. Modified machines

are not covered by warranty or product liability.

► Always use original parts and accessories.

► Change damaged parts immediately.

► Replace worn components in good time.

Storage, precautions

♦

Keep the machine and tools in a safe place, out

of the reach of children and locked up.

9800 0555 90a | Original instructions10

CP 1230 SPDR, CP 1240 SPDRSafety and operating instructions

Overview

To reduce the risk of serious injury or death

to yourself or others, read the Safety

instructions section found on the previous

pages of this manual before operating the

machine.

Design and function

CP 1230 SPDR and CP 1240 SPDR are designed for

driving spikes in railroad, tent, construction, and

plant maintenance applications.

They have a open front head which accepts a variety

of objects for driving. The maximum head diameter

of objects is 1

3

⁄

4

in. (44 mm). The pneumatic spike

drivers are designed for vertical use only. No other

use is permitted.

Main parts

A

B

C

D

E

F

A. Start and stop device

B. Handle

C. Back head

D. Air intake

E. Muffler

F. Front head

Labels

The machine is fitted with labels containing

important information about personal safety and

machine maintenance. The labels must be in such

condition that they are easy to read. New labels can

be ordered from the spare parts list.

Data plate

A

B

C

D

E

A. Machine type

B. Maximum permitted compressed air pressure

C. Serial number

D. The warning symbol together with the book

symbol means that the user must read the

safety and operating instructions before the

machine is used for the first time.

E. The CE symbol means that the machine is

EC-approved. See the EC declaration which is

delivered with the machine for more

information. If the CE symbol is missing, it

means that the machine is not EC-approved.

Noise level label

WA

xxx

dB

The label indicates the guaranteed noise level

corresponding to EC-directive 2000/14/EC. See

"Technical data" for accurate noise level.

Safety label

119800 0555 90a | Original instructions

Safety and operating instructionsCP 1230 SPDR, CP 1240 SPDR

To avoid injury, before using or servicing tool, read

and understand separately provided safety

instructions.

Installation

Hoses and connections

SRNO

A

B

C

D

A. Compressed air source

B. Water separator (optional)

C. Oiler (optional)

D. Max. 10 feet (3 meter) compressed air hose

between the oiler and the machine.

♦

Check that you are using the correct

recommended operating pressure, 87 psig (6 bar

(e)).

♦

The maximum permissible air pressure, 90 psig

(6.2 bar (e)), must not be exceeded.

♦

Blow any impurities out of the compressed air

hose before connecting it to the machine.

♦

Select the correct dimension and length for the

compressed air hose. For hose lengths up to 100

feet (30 meters), a hose with a minimum internal

diameter of

3

⁄

4

in. (19 mm) should be used. If the

hose length is between 100 and 330 feet (30 and

100 meters), a hose with a minimum internal

diameter of 1 in. (25 mm) should be used.

Methods to prevent freezing

Ice formation in the muffler can occur when the

ambient air temperature is 32-50 °F (0-10 °C) and

the relative humidity is high.

The machine is designed to avoid the formation of

ice in the muffler. Despite this, under extreme

conditions ice can form in the muffler.

The following actions can be taken to further

counteract the risk of ice formation:

♦

Use CP Airolene Plus Tool Oil as a lubricant. CP

Airolene Plus Tool Oil counteracts freezing.

♦

Use a water separator.

Connecting a water

separator

The length of the air hose between the compressor

and the water separator must be such that the water

vapor is cooled and condenses in the hose before

reaching the water separator.

If the ambient temperature is below 32 °F (0 °C) the

hose must be short enough to prevent the water

from freezing before reaching the water separator.

Lubrication

The lubricant is important for the machine’s function

and has a great impact on the service life. In order

to supply the correct volume of oil, an oiler should

be connected to the air hose. The use of Chicago

Pneumatic air line oiler is recommended. To

guarantee good lubrication, the length of the air

hose between the oiler and the pneumatic tool

should not exceed 10 feet (3 m).

Too much lubrication can cause starting problems,

low power or uneven performance.

Use a synthetic lubricant such as CP Airolene Plus

Tool Oil or mineral oil with the properties

recommended in the table below.

Viscosity

Temperature

range °F (°C)Lubricant

--4 to +120

(-20 to +50)

CP Airolene Plus

Tool Oil

100-150 SUS

(ISO VG 22-32)

-4 to +60

(-20 to +15)

Air tool oil

225-350 SUS

(ISO VG 46-68)

+60 to +120

(+15 to +50)

Air tool oil

It is recommended that the oil contains a

rust-inhibitor.

Checking the level and filling lubricant

♦

Oil levels should be checked daily.

♦

Wipe clean around the oil plug and remove it.

♦

Check that the threads are not damaged or worn

out.

♦

Any part with damaged or worn out threads must

be replaced.

♦

Fill lubricant in (A).

9800 0555 90a | Original instructions12

CP 1230 SPDR, CP 1240 SPDRSafety and operating instructions

A

♦

Tighten the plug firmly and wipe off any excessive

oil.

Operation

WARNING Involuntary start

Involuntary start of the machine may cause injury.

► Keep your hands away from the start and stop

device until you are ready to start the machine.

► Learn how the machine is switched off in the event

of an emergency.

► Stop the machine immediately in all cases of

power supply interruption.

Start and stop

Start the pneumatic spike driver by pressing down

the start and stop device.

Stop the pneumatic spike driver by releasing the

start and stop device. The start and stop device will

automatically return to the stop position.

Operating

♦

Make sure spikes that are to be driven are properly

set.

♦

Place the spike driver on top of the spike and align

the spike driver with spike.

♦

Stand in a stable position with your feet well away

from the spike.

♦

Apply a steady pressure on the spike and start

driving.

♦

Release the start stop device when the spike is

properly seated.

♦

Let the machine do the work; do not press too

hard.

♦

Any form of idling or operating with an uplifted

machine must be avoided.

♦

When the machine is lifted, the start and stop

device must not be activated.

♦

Check regularly that the machine is well

lubricated.

NOTICE Never hold or touch the spike when

driving.

When taking a break

♦

During all breaks you must place the machine in

such a way that there is no risk for it to be

unintentionally started. Make sure to place the

machine on the ground, so that it can not fall.

♦

In the event of a longer break or when leaving the

workplace: Switch off the power supply and then

bleed the machine by activating the start and stop

device.

Maintenance

Regular maintenance is a basic requirement for the

continued safe and efficient use of the machine.

Follow the maintenance instructions carefully.

139800 0555 90a | Original instructions

Safety and operating instructionsCP 1230 SPDR, CP 1240 SPDR

♦

Before starting maintenance on the machine,

clean it in order to avoid exposure to hazardous

substances. See “Dust and fume hazards”

♦

Use only authorised parts. Any damage or

malfunction caused by the use of unauthorised

parts is not covered by warranty or product

liability.

♦

When cleaning mechanical parts with solvent,

comply with appropriate health and safety

regulations and ensure there is satisfactory

ventilation.

♦

For major service of the machine, contact the

nearest authorised workshop.

♦

After each service, check that the machine's

vibration level is normal. If not, contact the nearest

authorised workshop.

Every day

Before undertaking any maintenance on pneumatic

machines, always switch off the air supply and bleed

the machine by depressing the start and stop device.

Then disconnect the air hose from the machine.

♦

Clean and inspect the machine and its functions

each day before the work commences.

♦

Conduct a general inspection for leaks and

damage.

♦

Check that the air inlet nipple is tightened and

that the claw coupling is free from damage.

♦

Change damaged parts immediately.

♦

Replace worn components in good time.

♦

Make sure that all the attached and related

equipment, such as hoses, water separators, and

oilers are properly maintained.

Assembly instructions

Reasonable care must be taken during assembly and

disassembly of the tool to avoid burring, scoring or

distortion of closely fitting precision built parts.

1. Check all metal to metal surfaces for nicks and

burrs before and during assembly.

2. Before re-assembly, lubricate all O-rings and coat

all moving parts of tool with recommended

lubricants.

3. During assembly take care to keep dirt out of

tool, particularly between mating surfaces.

4. The front head bolts must be tightened so that

the springs or bushings are evenly compressed.

5. When assembly is complete pour about ½ oz.

(1.5cl) of the recommended oil into the air inlet

and operate the pneumatic spike driver at

reduced throttle for 10–15 seconds. When

operating the pneumatic spike driver on the

floor, do so at reduced throttle to avoid damage

to piston, anvil block, and front head.

6. Before assembling the back head onto the

cylinder, check that the seal protrudes

approximately (B)

1

⁄

16

in. (1.6 mm) from the face

of the cylinder.

B

Periodic maintenance

After each operating period of approximately 150

impact hours or twice a year the machine must be

dismantled and all parts be cleaned and checked.

This work must be performed by authorized staff,

trained for this task.

1. Be sure that mating surfaces are clean and

smooth and that the bolts are tight.

2. Thoroughly clean and inspect internal parts and

make sure they are free from rust, grit and

foreign matter.

3. Thoroughly clean and inspect valve parts. Be

sure that the valve moves freely.

9800 0555 90a | Original instructions14

CP 1230 SPDR, CP 1240 SPDRSafety and operating instructions

4. Make sure that striking faces on the anvil block

are parallel and flat. If the block is cupped, grind

off high edges but do not touch the polished

face where the anvil strikes the steel shank.

Maximum allowed wear (A)

1

⁄

32

in. (1mm). See

illustration shown below.

A

Tightening torques

A

B

C

E

A. Torque: CP 1230 SPDR, 100-125 lbf.ft

(135-170 Nm) and CP 1240 SPDR, 125-150

lbf.ft (170- 203Nm).

B. The cylinder seal must protrude approximately

1

⁄

16

in. (1.6 mm) before assembly of the back

head.

C. Torque: 125–150 lbf.ft (170-203Nm). Apply

Loctite® 242™ (Loctite is a registered trademark

of Henkel Corporation. 242 is a trademark of

Henkel Corporation).

D. Torque, Muffler (not illustrated) 6–7lbf.ft

(8–10 Nm).

E. Assembled length of spring or bushing.

Min-Max length

in. (mm)Model

2

1

⁄

8

–2

3

⁄

16

(54.0–55.6)CP 1230 SPDR

2

17

⁄

32

–2

19

⁄

32

(64.3–65.9)CP 1240 SPDR

Troubleshooting

If the pneumatic machine does not start, has low

power or uneven performance, check the following

points.

159800 0555 90a | Original instructions

Safety and operating instructionsCP 1230 SPDR, CP 1240 SPDR

♦

Check that the pneumatic machine is getting the

correct amount of lubricant. Too much lubrication

can cause starting problems, low power or

uneven performance.

♦

Check that the compressed air system supplies

the machine with sufficient air pressure to give

full power.

♦

Check that the dimension and length of the air

hose are according to the recommendations. See

“Installation”.

♦

If there is a risk of freezing, check that the

machine's exhaust ports are not blocked.

♦

If the machine function is still not satisfactory after

this procedure, contact an authorised service

workshop.

Storage

> Clean the machine properly before storage, in

order to avoid hazardous substances. See “Dust

and fume hazard”

> Pour approximately

1

⁄

2

oz (5 cl) of oil directly into

the air inlet nipple, connect the machine to the

compressed air supply and start it for a few

seconds.

> Always store the machine in a dry place.

Disposal

A used machine must be treated and disposed of in

such a way that the greatest possible portion of the

material can be recycled and any negative influence

on the environment is kept as low as possible, and

in respect to local restrictions.

9800 0555 90a | Original instructions16

CP 1230 SPDR, CP 1240 SPDRSafety and operating instructions

Technical data

Machine data

Air

Consumption

cfm

(l/s)

Impact freq.

bpm

(Hz)

Length

in.

(mm)

Weight

lb

(kg)

Maximum head diameter

in.

(mm)Type

68

(32)

1300

(21.5)

24.6

(625)

63

(28.5)

1

3

⁄

4

(44)

CP 1230 SPDR

68

(32)

1300

(21.5)

24.6

(625)

66

(30)

1

3

⁄

4

(44)

CP 1230 S SPDR

85

(40)

1150

(19)

26.2

(665)

81.5

(37)

1

3

⁄

4

(44)

CP 1240 SPDR

85

(40)

1150

(19)

26.2

(665)

85

(38.5)

1

3

⁄

4

(44)

CP 1240 S SPDR

Noise and vibration declaration statement

Guaranteed sound power level Lw according to EN ISO 3744 in accordance with directive 2000/14/EC.

Sound pressure level Lp according to EN ISO 11203.

Vibration value A and uncertainty B determined according to EN ISO 20643. See table ”Noise and vibration

data” for the values of A, B, etc.

These declared values were obtained by laboratory type testing in accordance with the stated directive or

standards and are suitable for comparison with the declared values of other tools tested in accordance with

the same directive or standards. These declared values are not suitable for use in risk assessments and values

measured in individual work places may be higher. The actual exposure values and risk of harm experienced

by an individual user are unique and depend upon the way the user works, in what material the machine is

used, as well as upon the exposure time and the physical condition of the user, and the condition of the

machine.

We, Atlas Copco Construction Tools AB, cannot be held liable for the consequences of using the declared

values, instead of values reflecting the actual exposure, in an individual risk assessment in a work place situation

over which we have no control.

This tool may cause hand-arm vibration syndrome if its use is not adequately managed. An EU guide to

managing hand-arm vibration can be found at

http://www.humanvibration.com/humanvibration/EU/VIBGUIDE.html

We recommend a programme of health surveillance to detect early symptoms which may relate to vibration

exposure, so that management procedures can be modified to help prevent future impairment.

Noise and vibration data

VibrationNoise

Three axes valuesSound powerSound pressure

Declared valuesDeclared values

EN ISO 206432000/14/ECEN ISO 11203

B

m/s

2

spreads

A

m/s

2

value

Lw

guaranteed dB(A) rel

1pW

Lp

r=1m dB(A) rel 20µPaType

2.318.2--CP 1230 SPDR

2.318.210895CP 1230 S SPDR

2.015.3--CP 1240 SPDR

2.015.311198CP 1240 S SPDR

179800 0555 90a | Original instructions

Safety and operating instructionsCP 1230 SPDR, CP 1240 SPDR

EC Declaration of Conformity

EC Declaration of Conformity (EC Directive 2006/42/EC)

We, Atlas Copco Construction Tools AB, hereby declare that the machines listed below conform to the provisions

of EC Directive 2006/42/EC (Machinery Directive) and 2000/14/EC (Noise Directive), and the harmonised

standards mentioned below.

Pmax (bar)

Measured sound power

level [dB(A)]

Guaranteed sound power

level [dB(A)]

Handheld

pneumatic spike

drivers

6.2106108CP 1230 S SPDR

6.2109111CP 1240 S SPDR

Following harmonised standards were applied:

♦

EN ISO 11148-4

Following other standards were applied:

♦

Lloyds Register Quality Assurance, NoBo no.0088

Technical Documentation authorised representative:

Per Forsberg

Atlas Copco Construction Tools AB

Dragonvägen 2

Kalmar

Vice president Design and Development:

Erik Sigfridsson

Manufacturer:

Atlas Copco Construction Tools AB

105 23 Stockholm

Sweden

Place and date:

Kalmar, 2012-06-30

9800 0555 90a | Original instructions18

CP 1230 SPDR, CP 1240 SPDRSafety and operating instructions

199800 0555 90a | Instructions d’origine

SommaireCP 1230 SPDR, CP 1240 SPDR

FRANÇAIS

Sommaire

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

À propos des prescriptions de sécurité et des instructions pour l'opérateur. . . . . . 21

Consignes de sécurité. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Indications de sécurité. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Précautions et qualifications du personnel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Installation, précautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Fonctionnement, précautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Maintenance, précautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Stockage, précautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Vue d'ensemble. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Conception et fonctionnement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Principales pièces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Étiquettes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Flexibles et connexions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Mesures de prévention du gel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Branchement d'un séparateur d'eau. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Lubrification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Commande. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Marche/arrêt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Utilisation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Lors des pauses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Chaque jour. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Instructions de montage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Maintenance périodique. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Couples de serrage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Recherche de pannes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Stockage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Destruction d'une machine usagée. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Caractéristiques techniques. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Caractéristiques de la machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Énoncé déclaratif sur les vibrations et le bruit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Données relatives au bruit et aux vibrations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Déclaration CE de conformité. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Déclaration CE de conformité (Directive 2006/42/CE). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

9800 0555 90a | Instructions d’origine20

CP 1230 SPDR, CP 1240 SPDRSommaire

La pagina sta caricando ...

Chicago Pneumatic CP 1230 SPDR, CP 1240 SPDR Istruzioni per l'uso

Chicago Pneumatic CP 1230 SPDR, CP 1240 SPDR Istruzioni per l'uso

in altre lingue

Documenti correlati

Altri documenti