ISTRUZIONI PER L’USO - NORME DI INSTALLAZIONE
INSTRUCTIONS FOR USE - DIRECTIONS FOR INSTALLATION
INSTRUCTIONS - REGLES D’INSTALLATION
INSTRUCCIONES PARA EL USO - NORMAS PARA LA INSTALACION
GEBRAUCHSANLEITUNG - ANWEISUNGEN ZUR INSTALLATION
GEBRUIKSAANWIJZINGEN – INSTALLATIEVOORSCHRIFTEN
GEO 07GEO 07
GEO 07GEO 07
GEO 07
GEO 07GEO 07
GEO 07GEO 07
GEO 07
AVVERTENZE PER L’INSTALLATORE
OBBLIGHI GENERALI PER LA SICUREZZA
1) ATTENZIONE! È importante per la sicurezza delle persone seguire
attentamente tutta l’istruzione. Una errata installazione o un errato
uso del prodotto può portare a gravi danni alle persone.
2) Leggere attentamente le istruzioni prima di iniziare l’installazione del prodot-
to.
3) I materiali dell’imballaggio (plastica, polistirolo, ecc.) non devono essere
lasciati alla portata dei bambini in quanto potenziali fonti di pericolo.
4) Conservare le istruzioni per riferimenti futuri.
5) Questo prodotto è stato progettato e costruito esclusivamente per l’utilizzo
indicato in questa documentazione. Qualsiasi altro utilizzo non espressa-
mente indicato potrebbe pregiudicare l’integrità del prodotto e/o rappre-
sentare fonte di pericolo.
6) GENIUS declina qualsiasi responsabilità derivata dall’uso improprio o diverso da
quello per cui l’automatismo è destinato.
7) Non installare l’apparecchio in atmosfera esplosiva: la presenza di gas o fumi
infiammabili costituisce un grave pericolo per la sicurezza.
8) Gli elementi costruttivi meccanici devono essere in accordo con quanto
stabilito dalle Norme EN 12604 e EN 12605.
Per i Paesi extra-CEE, oltre ai riferimenti normativi nazionali, per ottenere un
livello di sicurezza adeguato, devono essere seguite le Norme sopra ripor-
tate.
9) GENIUS non è responsabile dell’inosservanza della Buona Tecnica nella co-
struzione delle chiusure da motorizzare, nonché delle deformazioni che
dovessero intervenire nell’utilizzo.
10) L’installazione deve essere effettuata nell’osservanza delle Norme EN 12453
e EN 12445. Il livello di sicurezza dell’automazione deve essere C+D.
11) Prima di effettuare qualsiasi intervento sull’impianto, togliere l’alimentazione
elettrica e scollegare le batterie.
12) Prevedere sulla rete di alimentazione dell’automazione un interruttore
onnipolare con distanza d’apertura dei contatti uguale o superiore a 3
mm. È consigliabile l’uso di un magnetotermico da 6A con interruzione
onnipolare.
13) Verificare che a monte dell’impianto vi sia un interruttore differenziale con
soglia da 0,03 A.
14) Verificare che l’impianto di terra sia realizzato a regola d’arte e collegarvi
le parti metalliche della chiusura.
15) L’automazione dispone di una sicurezza intrinseca antischiacciamento
costituita da un controllo di coppia. E' comunque necessario verificarne
la sogli di intervento secondo quanto previsto dalle Norme indicate al punto
10.
16) I dispositivi di sicurezza (norma EN 12978) permettono di proteggere eventuali
aree di pericolo da Rischi meccanici di movimento, come ad Es. schiac-
ciamento, convogliamento, cesoiamento.
17) Per ogni impianto è consigliato l’utilizzo di almeno una segnalazione lumi-
nosa nonché di un cartello di segnalazione fissato adeguatamente sulla
struttura dell’infisso, oltre ai dispositivi citati al punto “16”.
18) GENIUS declina ogni responsabilità ai fini della sicurezza e del buon funzio-
namento dell’automazione, in caso vengano utilizzati componenti del-
l’impianto non di produzione GENIUS.
19) Per la manutenzione utilizzare esclusivamente parti originali GENIUS.
20) Non eseguire alcuna modifica sui componenti facenti parte del sistema
d’automazione.
21) L’installatore deve fornire tutte le informazioni relative al funzionamento
manuale del sistema in caso di emergenza e consegnare all’Utente utiliz-
zatore dell’impianto il libretto d’avvertenze allegato al prodotto.
22) Non permettere ai bambini o persone di sostare nelle vicinanze del prodotto
durante il funzionamento.
23) Tenere fuori dalla portata dei bambini radiocomandi o qualsiasi altro datore
di impulso, per evitare che l’automazione possa essere azionata involon-
tariamente.
24) Il transito tra le ante deve avvenire solo a cancello completamente aperto.
25) L’Utente utilizzatore deve astenersi da qualsiasi tentativo di riparazione o
d’intervento diretto e rivolgersi solo a personale qualificato.
26) Tutto quello che non è previsto espressamente in queste istruzioni non è
permesso
IMPORTANT NOTICE FOR THE INSTALLER
GENERAL SAFETY REGULATIONS
1) ATTENTION! To ensure the safety of people, it is important that you read all
the following instructions. Incorrect installation or incorrect use of the
product could cause serious harm to people.
2) Carefully read the instructions before beginning to install the product.
3) Do not leave packing materials (plastic, polystyrene, etc.) within reach of
children as such materials are potential sources of danger.
4) Store these instructions for future reference.
5) This product was designed and built strictly for the use indicated in this
documentation. Any other use, not expressly indicated here, could com-
promise the good condition/operation of the product and/or be a source
of danger.
6) GENIUS declines all liability caused by improper use or use other than that for
which the automated system was intended.
7) Do not install the equipment in an explosive atmosphere: the presence of
inflammable gas or fumes is a serious danger to safety.
8) The mechanical parts must conform to the provisions of Standards EN 12604
and EN 12605.
For non-EU countries, to obtain an adequate level of safety, the Standards
mentioned above must be observed, in addition to national legal regulations.
9) GENIUS is not responsible for failure to observe Good Technique in the
construction of the closing elements to be motorised, or for any deformation
that may occur during use.
10) The installation must conform to Standards EN 12453 and EN 12445. The safety
level of the automated system must be C+D.
11) Before attempting any job on the system, cut out electrical power and
disconnect the batteries.
12) The mains power supply of the automated system must be fitted with an
all-pole switch with contact opening distance of 3mm or greater. Use of
a 6A thermal breaker with all-pole circuit break is recommended.
13) Make sure that a differential switch with threshold of 0.03 A is fitted upstream
of the system.
14) Make sure that the earthing system is perfectly constructed, and connect
metal parts of the means of the closure to it.
15) The automated system is supplied with an intrinsic anti-crushing safety device
consisting of a torque control. Nevertheless, its tripping threshold must be
checked as specified in the Standards indicated at point 10.
16) The safety devices (EN 12978 standard) protect any danger areas against
mechanical movement Risks, such as crushing, dragging, and shearing.
17) Use of at least one indicator-light is recommended for every system, as well
as a warning sign adequately secured to the frame structure, in addition
to the devices mentioned at point “16”.
18) GENIUS declines all liability as concerns safety and efficient operation of the
automated system, if system components not produced by GENIUS are
used.
19) For maintenance, strictly use original parts by GENIUS.
20) Do not in any way modify the components of the automated system.
21) The installer shall supply all information concerning manual operation of the
system in case of an emergency, and shall hand over to the user the
warnings handbook supplied with the product.
22) Do not allow children or adults to stay near the product while it is operating.
23) Keep remote controls or other pulse generators away from children, to
prevent the automated system from being activated involuntarily.
24) Transit through the leaves is allowed only when the gate is fully open.
25) The user must not attempt any kind of repair or direct action whatever and
contact qualified personnel only.
26) Anything not expressly specified in these instructions is not permitted.
CONSIGNES POUR L'INSTALLATEUR
RÈGLES DE SÉCURITÉ
1) ATTENTION! Il est important, pour la sécurité des personnes, de suivre à la
lettre toutes les instructions. Une installation erronée ou un usage erroné
du produit peut entraîner de graves conséquences pour les personnes.
2) Lire attentivement les instructions avant d'installer le produit.
3) Les matériaux d'emballage (matière plastique, polystyrène, etc.) ne doivent
pas être laissés à la portée des enfants car ils constituent des sources
potentielles de danger.
4) Conserver les instructions pour les références futures.
5) Ce produit a été conçu et construit exclusivement pour l'usage indiqué dans
cette documentation. Toute autre utilisation non expressément indiquée
pourrait compromettre l'intégrité du produit et/ou représenter une source
de danger.
6) GENIUS décline toute responsabilité qui dériverait d'usage impropre ou différent
de celui auquel l'automatisme est destiné.
7) Ne pas installer l'appareil dans une atmosphère explosive: la présence de gaz
ou de fumées inflammables constitue un grave danger pour la sécurité.
8) Les composants mécaniques doivent répondre aux prescriptions des Normes
EN 12604 et EN 12605.
Pour les Pays extra-CEE, l'obtention d'un niveau de sécurité approprié exige
non seulement le respect des normes nationales, mais également le respect
des Normes susmentionnées.
9) GENIUS n'est pas responsable du non-respect de la Bonne Technique dans
la construction des fermetures à motoriser, ni des déformations qui pourraient
intervenir lors de l'utilisation.
10) L'installation doit être effectuée conformément aux Normes EN 12453 et EN
12445. Le niveau de sécurité de l'automatisme doit être C+D.
11) Couper l'alimentation électrique et déconnecter la batterie avant toute
intervention sur l'installation.
12) Prévoir, sur le secteur d'alimentation de l'automatisme, un interrupteur
omnipolaire avec une distance d'ouverture des contacts égale ou
supérieure à 3 mm. On recommande d'utiliser un magnétothermique de
6A avec interruption omnipolaire.
13) Vérifier qu'il y ait, en amont de l'installation, un interrupteur différentiel avec
un seuil de 0,03 A.
14) Vérifier que la mise à terre est réalisée selon les règles de l'art et y connecter
les pièces métalliques de la fermeture.
15) L'automatisme dispose d'une sécurité intrinsèque anti-écrasement, formée
d'un contrôle du couple. Il est toutefois nécessaire d'en vérifier le seuil
d'intervention suivant les prescriptions des Normes indiquées au point 10.
16) Les dispositifs de sécurité (norme EN 12978) permettent de protéger des
zones éventuellement dangereuses contre les Risques mécaniques du
mouvement, comme l'écrasement, l'acheminement, le cisaillement.
17) On recommande que toute installation soit doté au moins d'une signalisation
lumineuse, d'un panneau de signalisation fixé, de manière appropriée, sur
la structure de la fermeture, ainsi que des dispositifs cités au point “16”.
18) GENIUS décline toute responsabilité quant à la sécurité et au bon
fonctionnement de l'automatisme si les composants utilisés dans l'installation
n'appartiennent pas à la production GENIUS.
19) Utiliser exclusivement, pour l'entretien, des pièces GENIUS originales.
20) Ne jamais modifier les composants faisant partie du système d'automatisme.
21) L'installateur doit fournir toutes les informations relatives au fonctionnement
manuel du système en cas d'urgence et remettre à l'Usager qui utilise
l'installation les "Instructions pour l'Usager" fournies avec le produit.
22) Interdire aux enfants ou aux tiers de stationner près du produit durant le
fonctionnement.
23) Eloigner de la portée des enfants les radiocommandes ou tout autre
générateur d'impulsions, pour éviter tout actionnement involontaire de
l'automatisme.
24) Le transit entre les vantaux ne doit avoir lieu que lorsque le portail est
complètement ouvert.
25) L'Usager qui utilise l'installation doit éviter toute tentative de réparation ou
d'intervention directe et s'adresser uniquement à un personnel qualifié.
26) Tout ce qui n'est pas prévu expressément dans ces instructions est interdit.
ADVERTENCIAS PARA EL INSTALADOR
REGLAS GENERALES PARA LA SEGURIDAD
1) ATENCION! Es sumamente importante para la seguridad de las personas
seguir atentamente las presentes instrucciones. Una instalación incorrecta
o un uso impropio del producto puede causar graves daños a las
personas.
2) Lean detenidamente las instrucciones antes de instalar el producto.
3) Los materiales del embalaje (plástico, poliestireno, etc.) no deben dejarse al
alcance de los niños, ya que constituyen fuentes potenciales de peligro.
4) Guarden las instrucciones para futuras consultas.
5) Este producto ha sido proyectado y fabricado exclusivamente para la
utilización indicada en el presente manual. Cualquier uso diverso del
previsto podría perjudicar el funcionamiento del producto y/o representar
fuente de peligro.
6) GENIUS declina cualquier responsabilidad derivada de un uso impropio o
diverso del previsto.
7) No instalen el aparato en atmósfera explosiva: la presencia de gas o humos
inflamables constituye un grave peligro para la seguridad.
8) Los elementos constructivos mecánicos deben estar de acuerdo con lo
establecido en las Normas EN 12604 y EN 12605.
Para los países no pertenecientes a la CEE, además de las referencias
normativas nacionales, para obtener un nivel de seguridad adecuado,
deben seguirse las Normas arriba indicadas.
9) GENIUS no es responsable del incumplimiento de las buenas técnicas de
fabricación de los cierres que se han de motorizar, así como de las
deformaciones que pudieran intervenir en la utilización.
10) La instalación debe ser realizada de conformidad con las Normas EN 12453
y EN 12445. El nivel de seguridad de la automación debe ser C+D.
11) Quiten la alimentación eléctrica y desconecten las baterías antes de
efectuar cualquier intervención en la instalación.
12) Coloquen en la red de alimentación de la automación un interruptor
omnipolar con distancia de apertura de los contactos igual o superior a
3 mm. Se aconseja usar un magnetotérmico de 6A con interrupción
omnipolar.
13) Comprueben que la instalación disponga línea arriba de un interruptor
diferencial con umbral de 0,03 A.
14) Verifiquen que la instalación de tierra esté correctamente realizada y
conecten las partes metálicas del cierre.
15) La automación dispone de un dispositivo de seguridad antiaplastamiento
constituido por un control de par. No obstante, es necesario comprobar
el umbral de intervención según lo previsto en las Normas indicadas en el
punto 10.
16) Los dispositivos de seguridad (norma EN 12978) permiten proteger posibles
áreas de peligro de Riesgos mecánicos de movimiento, como por ej.
aplastamiento, arrastre, corte.
17) Para cada equipo se aconseja usar por lo menos una señalización luminosa
así como un cartel de señalización adecuadamente fijado a la estructura
del bastidor, además de los dispositivos indicados en el “16”.
18) GENIUS declina toda responsabilidad relativa a la seguridad y al buen
funcionamiento de la automación si se utilizan componentes de la
instalación que no sean de producción GENIUS.
19) Para el mantenimiento utilicen exclusivamente piezas originales GENIUS
20) No efectúen ninguna modificación en los componentes que forman
parte del sistema de automación.
21) El instalador debe proporcionar todas las informaciones relativas al
funcionamiento del sistema en caso de emergencia y entregar al usuario
del equipo el manual de advertencias que se adjunta al producto.
22) No permitan que niños o personas se detengan en proximidad del producto
durante su funcionamiento.
23) Mantengan lejos del alcance los niños los telemandos o cualquier otro
emisor de impulso, para evitar que la automación pueda ser accionada
involuntariamente.
24) Sólo puede transitarse entre las hojas si la cancela está completamente
abierta.
25) El usuario no debe por ningún motivo intentar reparar o modificar el
producto, debe siempre dirigirse a personal cualificado.
26) Todo lo que no esté previsto expresamente en las presentes instrucciones
debe entenderse como no permitido
HINWEISE FÜR DEN INSTALLATIONSTECHNIKER
ALLGEMEINE SICHERHEITSVORSCHRIFTEN
1) ACHTUNG! Um die Sicherheit von Personen zu gewährleisten, sollte die
Anleitung aufmerksam befolgt werden. Eine falsche Installation oder ein
fehlerhafter Betrieb des Produktes können zu schwerwiegenden
Personenschäden führen.
2) Bevor mit der Installation des Produktes begonnen wird, sollten die Anleitungen
aufmerksam gelesen werden.
3) Das Verpackungsmaterial (Kunststoff, Styropor, usw.) sollte nicht in Reichweite
von Kindern aufbewahrt werden, da es eine potentielle Gefahrenquelle
darstellt.
4) Die Anleitung sollte aufbewahrt werden, um auch in Zukunft Bezug auf sie
nehmen zu können.
5) Dieses Produkt wurde ausschließlich für den in diesen Unterlagen
angegebenen Gebrauch entwickelt und hergestellt. Jeder andere
Gebrauch, der nicht ausdrücklich angegeben ist, könnte die Unversehrtheit
des Produktes beeinträchtigen und/oder eine Gefahrenquelle darstellen.
6) Die Firma GENIUS lehnt jede Haftung für Schäden, die durch unsachgemäßen
oder nicht bestimmungsgemäßen Gebrauch der Automatik verursacht
werden, ab.
7) Das Gerät sollte nicht in explosionsgefährdeten Umgebungen installiert werden:
das Vorhandensein von entflammbaren Gasen oder Rauch stellt ein
schwerwiegendes Sicherheitsrisiko dar.
8) Die mechanischen Bauelemente müssen den Anforderungen der Normen
EN 12604 und EN 12605 entsprechen.
Für Länder, die nicht der Europäischen Union angehören, sind für die
Gewährleistung eines entsprechenden Sicherheitsniveaus neben den
nationalen gesetzlichen Bezugsvorschriften die oben aufgeführten Normen
zu beachten.
9) Die Firma GENIUS übernimmt keine Haftung im Falle von nicht fachgerechten
Ausführungen bei der Herstellung der anzutreibenden Schließvorrichtungen
sowie bei Deformationen, die eventuell beim Betrieb entstehen.
10) Die Installation muß unter Beachtung der Normen EN 12453 und EN 12445
erfolgen. Die Sicherheitsstufe der Automatik sollte C+D sein.
11) Vor der Ausführung jeglicher Eingriffe auf der Anlage sind die elektrische
Versorgung und die Batterie abzunehmen.
12) Auf dem Versorgungsnetz der Automatik ist ein omnipolarer Schalter mit
Öffnungsabstand der Kontakte von über oder gleich 3 mm einzubauen.
Darüber hinaus wird der Einsatz eines Magnetschutzschalters mit 6A mit
omnipolarer Abschaltung empfohlen.
13) Es sollte überprüft werden, ob vor der Anlage ein Differentialschalter mit
einer Auslöseschwelle von 0,03 A zwischengeschaltet ist.
14) Es sollte überprüft werden, ob die Erdungsanlage fachgerecht ausgeführt
wurde. Die Metallteile der Schließung sollten an diese Anlage angeschlossen
werden.
15) Die Automation verfügt über eine eingebaute Sicherheitsvorrichtung für
den Quetschschutz, die aus einer Drehmomentkontrolle besteht. Es ist in
jedem Falle erforderlich, deren Eingriffsschwelle gemäß der Vorgaben der
unter Punkt 10 angegebenen Vorschriften zu überprüfen.
16) Die Sicherheitsvorrichtungen (Norm EN 12978) ermöglichen den Schutz
eventueller Gefahrenbereiche vor mechanischen Bewegungsrisiken, wie
zum Beispiel Quetschungen, Mitschleifen oder Schnittverletzungen.
17) Für jede Anlage wird der Einsatz von mindestens einem Leuchtsignal
empfohlen sowie eines Hinweisschildes, das über eine entsprechende
Befestigung mit dem Aufbau des Tors verbunden wird. Darüber hinaus sind
die unter Punkt “16” erwähnten Vorrichtungen einzusetzen.
18) Die Firma GENIUS lehnt jede Haftung hinsichtlich der Sicherheit und des
störungsfreien Betriebs der Automatik ab, soweit Komponenten auf der
Anlage eingesetzt werden, die nicht im Hause GENIUS hergestellt wurden.
19) Bei der Instandhaltung sollten ausschließlich Originalteile der Firma GENIUS
verwendet werden.
20) Auf den Komponenten, die Teil des Automationssystems sind, sollten keine
Veränderungen vorgenommen werden.
21) Der Installateur sollte alle Informationen hinsichtlich des manuellen Betriebs
des Systems in Notfällen liefern und dem Betreiber der Anlage das
Anleitungsbuch, das dem Produkt beigelegt ist, übergeben.
22) Weder Kinder noch Erwachsene sollten sich während des Betriebs in der
unmittelbaren Nähe der Automation aufhalten.
23) Die Funksteuerungen und alle anderen Impulsgeber sollten außerhalb der
Reichweite von Kindern aufbewahrt werden, um ein versehentliches
Aktivieren der Automation zu vermeiden.
24) Der Durchgang oder die Durchfahrt zwischen den Flügeln darf lediglich bei
vollständig geöffnetem Tor erfolgen.
25) Der Betreiber sollte keinerlei Reparaturen oder direkte Eingriffe auf der
Automation ausführen, sondern sich hierfür ausschließlich an qualifiziertes
Fachpersonal wenden.
26) Alle Vorgehensweisen, die nicht ausdrücklich in der vorliegenden Anleitung
vorgesehen sind, sind nicht zulässig
WAARSCHUWINGEN VOOR DE INSTALLATEUR
ALGEMENE VEILIGHEIDSVOORSCHRIFTEN
1) LET OP! Het is belangrijk voor de veiligheid dat deze hele instructie zorgvuldig
wordt opgevolgd. Een onjuiste installatie of foutief gebruik van het product
kunnen ernstig persoonlijk letsel veroorzaken.
2) Lees de instructies aandachtig door alvorens te beginnen met de installatie
van het product.
3) De verpakkingsmaterialen (plastic, polystyreen, enz.) mogen niet binnen het
bereik van kinderen worden gelaten, want zij vormen een mogelijke bron
van gevaar.
4) Bewaar de instructies voor raadpleging in de toekomst.
5) Dit product is uitsluitend ontworpen en gebouwd voor het doel dat in deze
documentatie wordt aangegeven. Elk ander gebruik, dat niet uitdrukkelijk
wordt vermeld, zou het product kunnen beschadigen en/of een bron
van gevaar kunnen vormen.
6) GENIUS aanvaardt geen enkele aansprakelijkheid voor schade die ontstaat
uit oneigenlijk gebruik of ander gebruik dan waarvoor het automatische
systeem is bedoeld.
7) Installeer het apparaat niet in een explosiegevaarlijke omgeving: de
aanwezigheid van ontvlambare gassen of dampen vormt een ernstig
gevaar voor de veiligheid.
8) De mechanische bouwelementen moeten in overeenstemming zijn met
de bepalingen van de normen EN 12604 en EN 12605.
Voor niet-EEG landen moeten, om een goed veiligheidsniveau te bereiken,
behalve de nationale voorschriften ook de bovenstaande normen in acht
worden genomen.
9) GENIUS is niet aansprakelijk als de regels der goede techniek niet in acht
genomen zijn bij de bouw van het sluitwerk dat gemotoriseerd moet
worden, noch voor vervormingen die zouden kunnen ontstaan bij het
gebruik.
10) De installatie dient te geschieden in overeenstemming met de normen EN
12453 en EN 12445. Het veiligheidsniveau van het automatische systeem
moet C+D zijn.
11) Alvorens ingrepen te gaan verrichten op de installatie moet de elektrische
voeding worden weggenomen en moeten de batterijen worden
afgekoppeld.
12) Zorg op het voedingsnet van het automatische systeem voor een meerpolige
schakelaar met een opening tussen de contacten van 3 mm of meer. Het
wordt geadviseerd een magnetothermische schakelaar van 6A te gebruiken
met meerpolige onderbreking.
13) Controleer of er bovenstrooms van de installatie een differentieelschakelaar
is geplaatst met een limiet van 0,03 A.
14) Controleer of de aardingsinstallatie vakkundig is aangelegd en sluit er de
metalen delen van het sluitsysteem op aan.
15) Het automatische systeem beschikt over een intrinsieke beveiliging tegen
inklemming, bestaande uit een controle van het koppel. De inschakellimiet
hiervan dient echter te worden gecontroleerd volgens de bepalingen van
de normen die worden vermeld onder punt 10.
16) De veiligheidsvoorzieningen (norm EN 12978) maken het mogelijk eventuele
gevaarlijke gebieden te beschermen tegen Mechanische gevaren door
beweging, zoals bijvoorbeeld inklemming, meesleuren of amputatie.
17) Het wordt voor elke installatie geadviseerd minstens één lichtsignaal te
gebruiken alsook een waarschuwingsbord dat goed op de constructie
van het hang- en sluitwerk dient te worden bevestigd, afgezien nog van
de voorzieningen die genoemd zijn onder punt “16”.
18) GENIUS aanvaardt geen enkele aansprakelijkheid voor wat betreft de veiligheid
en de goede werking van het automatische systeem, als er in de installatie
gebruik gemaakt wordt van componenten die niet door GENIUS zijn
geproduceerd.
19) Gebruik voor het onderhoud uitsluitend originele GENIUS-onderdelen.
20) Verricht geen wijzigingen op componenten die deel uitmaken van het
automatische systeem.
21) De installateur dient alle informatie te verstrekken over de handbediening
van het systeem in noodgevallen, en moet de gebruiker van de installatie
het bij het product geleverde boekje met aanwijzingen overhandigen.
22) Sta het niet toe dat kinderen of volwassenen zich ophouden in de buurt
van het product terwijl dit in werking is.
23) Houd radio-afstandsbedieningen of alle andere impulsgevers buiten het
bereik van kinderen, om te voorkomen dat het automatische systeem
onopzettelijk kan worden aangedreven.
24) Ga alleen tussen de vleugels door als het hek helemaal geopend is.
25) De gebruiker mag geen pogingen tot reparatie doen of directe ingrepen
plegen, en dient zich uitsluitend te wenden tot gekwalificeerd personeel.
26) Alles wat niet uitdrukkelijk in deze instructies wordt aangegeven, is niet
toegestaan
ENGLISH
8
CE DECLARATION OF CONFORMITY
Manufacturer: GENIUS S.p.A.
Address: Via Padre Elzi, 32 - 24050 - Grassobbio- Bergamo - ITALY
Declares that: control unit GEO 07
• conforms to the essential safety requirements of the following EEC directives:
73/23/EEC and subsequent amendment 93/68/EEC.
89/336/EEC and subsequent amendment 92/31/EEC and 93/68/EEC
Additional information:
This product underwent a test in a typical, uniform configuration (all products manufactured by GENIUS S.p.A.).
Grassobbio, 01-06-2006
The Managing Director
D. Gianantoni
Notes on reading the instruction
Read this installation manual to the full before you begin installing the product.
The symbol indicates notes that are important for the safety of persons and for the good condition of the
automated system
The symbol draws your attention to the notes on the characteristics and operation of the product.
INDEX
2. HARDWARE SPECIFICATIONS pag.9
3. BOARD LAY-OUT pag.9
1. OPERATING PARAMETERS pag.9
4. BOARD COMPONENTS pag.10
5. ELECTRICAL CONNECTIONS pag.10
5.1. DESCRIPTION OF CONNECTIONS pag.10
6. SIGNALLING LEDs pag.11
7. PROGRAMMING pag.12
7.1. BASIC PROGRAMMING pag.12
7.2. ADVANCED PROGRAMMING pag.12
8. ROTATION DIRECTION CHECK pag.14
9. ADJUSTMENT OF ELECTRONIC CLUTCH (ANTI-CRUSHING) pag.14
10. ENCODER OPERATION pag.14
ENGLISH
9
12345678910
11 12
13
14
15
16
PE
N
L
J3
J5
J4
J2
J1
+
-
F
FCA
OPEN
FCC
FSWOP
ENCODER
FSWCL
F2
F1
TF1
J3
LP1
J4
F2
TF1
DL
J1
F1
J2
P3P1 P2
cigoL citamotua-imes/citamotua
emitesuaP ).nim2tluafed(.nim4ot0morfelbammargorp
emitkroW ).ces02tluafed(.c
es95ot0morfelbammargorp
euqrotgnitratsxaM oN/seY
efaSliaF oN/seY
gnihsalf-erP ).ces0tluafed(.ces01ot0morfel
bammargorp
hctulccinortcelE slevel05noelbammargorp
edomnoitnevretnihctiws-timiL sedomgnitarepofosepyt4
gni
mitysetruoC ).ces03tluafed(.nim4ot0morfelbammargorp
edomnoitnevretnisecivedytefaS sedomgnitarepofosepyt3
ylppusrewoP zH05-CAV032
rewopdebrosba.xaM W21
daol.xamsrotoM W008
seirosseccarofylppusrewoP cdV42
daol.xamsei
rosseccA Am003
erutarepmettneibmagnitarepO C°55+C°02-
sesuFevitcetorP tiucricseirossecca/sniam
gulpdipaR rev
ieceroidarnip5
sdraoblanimreT elbavomer
stupnidraoblanimreT
gninepO/secivedytefasgninepO/secivedytefasgni
solC/redocnE/nepO
W06-CAV032pmalgnihsalf/hctiws-timilgnisolC/hctiws-timil
stuptuodraoblanimreT cdV42seir
osseccaylppusrewopCAV032thgilysetruoclanretxerotom
ysetruocdetargetnirofdaol.xaM
thgil
W52
ysetruoclanret
xerofdaol.xaM
sthgil
W052
CONTROL UNIT GEO 07
The GEO 07 control unit was designed to command the opening of up-and-over doors with one or two motors.
Thanks to management by encoder and opening and closing limit-switches, if correctly installed, it can guarantee
installation in conformity with current safety regulations.
The SLAVE board, instead of the unit, has an electronic interface board on which the courtesy light is also fitted.
1. OPERATING PARAMETERS
2. HARDWARE SPECIFICATIONS
3. BOARD LAY-OUT
Fig. 1
ENGLISH
10
2
1
2
1
2
1
4
3
5
2
1
4
3
5
FSW CL
FSW OP
_
-FSW TX
FCA
FCC
FSW OP
FSW CL
OPEN
_
+
SIG.
ENCODER
1
2
3
4
5
6
7
8
9
10
J3
J1
F1
J2
230 V~
50Hz
COM
OP
CL
M
EXT. LAMP
FLASH LAMP
11 12 13 14 15
16
PE N L
MARRONE
BLU
NERO
230 V~
50Hz
COM
OP
CL
EXT. LAMP
11 12 13 14 15
16
PE N L
COM
OP
CL
6
4
5
FLASH LAMP
J1
F1
J2
M1
M2
230 V~
max.
25W
1F )tiucricsniam(V052/A502x51FesuF
2F )seirossecca(V052/Am00502x52FesuF
1FT remrofsnarT
1PL 41EV022W52thgily
setruoC
LD yalpsiD
1J draoblanimrettupniylppusrewopCAV032
2J thgilysetruoc.txednapmalgnihsalf,rotom:draob-l
animrettuptuO
3J draoblanimretseirossecca/stupniegatlovwoL
4J rotcennocdiparsdraobrevieceR
1P "nottub-hsupg
nimmargorP +"
2P "nottub-hsupgnimmargorP -"
3P "nottub-hsupgnimmargorP F"
4. BOARD COMPONENTS
5. ELECTRICAL CONNECTIONS
5.1. DESCRIPTION OF CONNECTIONS
For operation of the control unit with the encoder, the opening and closing limit-switches MUST be used.
5.1.1. TERMINAL BOARD J1 (high voltage)
Terminal board for 230V~ 50Hz (L= Phase N=Neutral) power supply.
Connect earth of electrical system and earth cable of the operator to terminal "PE".
5.1.2. TERMINAL BOARD J2 (high voltage)
230V~ Terminal board for connection of:
Motor: connect the motor phases (Black and Brown cables) to the OP and CL terminals. Connect the common contact
(Blue cable) to terminal COM. Connect the starting capacitor in parallel with respect to the phases.
Flashing lamp: connect the flashing lamp with max. 60W power supply between terminals 15 and 16.
Courtesy light: connect the courtesy light of the SLAVE board between terminals 14 and 16, or connect the external
courtesy lights with overall power of 250W between these terminals.
5.1.3. TERMINAL BOARD J3 (low voltage)
1 = = Inputs common contact /Negative pole for accessories supply
2 = = Inputs common contact /Negative pole for accessories supply
3 = = Positive pole for powering 24 Vdc (+) accessories
Accessories max. load: 300 mA.
To calculate absorption values, refer to the instructions for individual accessories.
Fig. 2
Fig. 3
ENGLISH
11
FCA
OPEN
FCC
FSWOP
ENCODER
FSWCL
DEL NO FFO
NEPO evitcadnammocgninepo evitcanidnammocgninepo
REDOCNE noitarepognirudsehsalfDEL
POWSF degagnesidseciv
edytefasgninepo degagnesecivedytefasgninepo
LCWSF degagnesidsecivedytefasgnisolc degagneecivedytefasgniso
lc
ACF eerfhctiws-timilgninepo degagnehctiws-timilgninepo
CCF eerfhctiws-timilgnisolc degagnehctiws-timilgn
isolc
=NODEL /tcatnocdesolc =FFODEL tcatnocnepo
4 = -FSW TX = Negative pole for power supply to photocell transmitters
Separate connection of the negative pole of the transmitters makes it possible to use the Failsafe control on the
photocells, thus increasing the system's safety level.
5 = FCA = Opening Limit-switch contact (N.C.)
The opening limit-switch consists of a micro-pushbutton which, activated by the cam when the door reaches open
position, stops movement immediately or, according to programming, after 3 sec.
6 = FCC = Closing Limit-switch contact (N.C.)
The closing limit-switch consists of a micro-pushbutton which, activated by the cam when the door reaches closed
position, stops movement immediately or, according to programming, after 3 sec.
For control unit operation, both limit-switches must be connected.
7 = FSW OP = Opening Safety Devices contact (N.C.)
Safety devices are all devices (photocells, sensitive edges,…) with N.C. contact, which, if there is an obstacle in the
area they protect, operate by stopping or reversing the door opening movement (see chap.7.2 - Advanced
programming).
They have no effect during the closing stage.
If the opening safety devices are engaged while the door is closed, they inhibit any Open pulse.
To install several safety devices, connect the N.C. contacts in series.
If no opening safety devices are connected, jumper connect "FSW OP" to the inputs common contact.
8 = FSW CL = Closing Safety Devices contact (N.C.)
Safety devices are all devices (photocells, sensitive edges,…) with N.C. contact, which, if there is an obstacle in the
area they protect, operate to reverse door closing movement. They have no effect during the opening stage, except
in the Ad function (see chap.5.3.1. - Advanced programming).
If the closing safety devices are engaged while the door is open, they inhibit any Open pulse.
To install several safety devices, connect the N.C. contacts in series.
If no closing safety devices are connected, jumper connect "FSW CL" to the inputs common contact.
9 = ENCODER = Input for encoder signal
The signal received from the encoder must be connected to this terminal. To supply power to the encoder, connect
the remaining two wires to terminals “1 - 3” observing the polarity indicated on the board.
The control unit will not operate without an encoder
For two-motor applications, the encoder must be applied only to motor 1 (the one with the unit)
10 = OPEN = OPEN Command (N.O.)
Any device (push-button, detector,…) which, by closing a contact, supplies an opening (or closing) pulse to the door.
To install several Open devices, connect N.O. contacts in parallel.
5.1.4. CONNECTOR J4 (low voltage)
Connector J4 is used for rapid connection of RECEIVING boards. The receiver board must be inserted with the components
facing the board.
Insert and remove the boards after cutting power.
6. SIGNALLING LEDs
A two-digit display is installed on the board. During normal operation, it
indicates the status of the inputs. Fig.4 shows the exact correspondence
between the horizontal segments (we will call them LEDs from now on) of
the display and the inputs.
The table below indicates the status of the LEDs in relation to the status of
the inputs.
TAB.1 STATUS OF LEDS
Fig. 4
ENGLISH
12
BASIC PROGRAMMING
Display
Function
Default
FUNCTION LOGICS:
= Automatic
= Semi-automatic
CLOSING SLOW START:
Settable from to sec.
PAUSE TIME:
This operates only if the automatic logic was selected. Can be adjusted from to sec.
in one second steps.
Next, the viewing changes in minutes and tenths of a second (separated by a dot) and time
is adjusted in 10 second steps, up to the maximum value of minutes.
E.g.: if the display shows , the pause time will be 2 min and 50 sec.
ELECTRONIC CLUTCH:
Limits the operator's maximum thrust.
Settable from (minimum force)
to (maximum force)
To exit programming and return to display of inputs status
ADVANCED PROGRAMMING
Display
Function
Default
COURTESY LIGHT:
For setting lighted time of the courtesy light.
Can be adjusted from to sec. in one second steps.
Next, the viewing changes in minutes and tenths of a second (separated by a dot) and time
is adjusted in 10 second steps, up to the maximum value of minutes.
E.g.: if the display shows , the lighted time will be 2 min and 50 sec.
MAXIMUM STARTING TORQUE:
= Active = Disabled
FAIL SAFE (safety devices operational check):
= Active = Disabled
7. PROGRAMMING
To program the operation of the automated system, you must access the "PROGRAMMING" mode.
Programming is in two parts: BASIC and ADVANCED.
7.1. BASIC PROGRAMMING
To access BASIC PROGRAMMING, use push-button F:
• if you press it (and hold it down), the display shows the name of the first function.
• if you release the push-button, the display shows the value of the function, which can be changed with keys + and -.
• if you press F again (and hold it down), the display shows the name of the next function, etc.
• when you reach the last function, press the F push-button to exit programming, and the display resumes showing the
inputs status.
The following table indicates the sequence of functions accessible in BASIC PROGRAMMING:
7.2. ADVANCED PROGRAMMING
To access ADVANCED PROGRAMMING, press push-button F and, while holding it down, press push-button +:
• if you release the + push-button, the display shows the name of the first function.
• if you also release the F push-button, the display shows the value of the function, which can be changed with keys + and -.
• if you press the F push-button (and hold it down), the display shows the name of the next function; if you release it, the
value is shown and can be changed with keys + and -.
• when you reach the last function, press the F push-button to exit programming, and the display resumes showing the
inputs status.
The following table indicates the sequence of functions accessible in ADVANCED PROGRAMMING:
ENGLISH
13
ADVANCED PROGRAMMING
Display
Function
Default
PRE-FLASHING of flashing lamp:
Can be adjusted from to sec. in one second steps.
LIMIT-SWITCH INTERVENTION MODE:
For setting motor operation when limit-switches (optionals) are reached:
=FCA/FCC: Stops immediately
=FCA/FCC: Stops after 3 sec. deceleration
=FCA: Stops immediately
FCC: Stops after 3 sec. at full speed
=FCA: Stops after 3 sec. deceleration
FCC: Stops after 2 sec. deceleration +1 sec. closing thrust
SAFETY DEVICES INTERVENTION MODE:
For setting motor operation when safety devices are engaged
= FSWOP stops opening movement which, on release, resumes opening. FSWCL reverses
closing movement.
= When up-and-over door is closed, open or locked and FSWCL are engaged, the Open
pulse activates the flashing lamp and movement begins only when FSWCL
(1)
(ADMAP
function) disengages. During the movement, FSWOP reverses, and FSWCL stops and reverses
on release
(1)
.
= FSWOP reverses the opening movement, FSWCL reverses closing movement.
(1)
With pre-flashing selected, movement begins after pre-flashing time.
To exit programming and return to display of inputs status
SESLUP
SUTATSROOD NEPO SECIVEDYTEFASGNISOLC SECIVEDYTEFASGNINEPO
DESOLC
esuapretfasesolcdnasnepo
emit
)1(
tceffeon
)noitcnufdAgnidulcxe(
tceffeon
)gninepostibihni(
ESUAPNINEPO emitesuapstnuoc-er
tceffeon
)gnisolcst
ibihni(
tceffeon
GNISOLC noitomsesrevernoitomsesrevertceffeon
GNINEPO tceffeontceffeongnimmargorPees
DEPPOTS ses
olc
)1(
tceffeon
)gnisolcstibihni(
tceffeon
SESLUP
SUTATSROOD NEPO SECIVEDYTEFASGNISOLC SECIVEDYTEFASGNINEPO
DESOLC snepo
)1(
tceffeon
)noitcnufdAgnidulcxe(
tceffeon
)gninepostibihni(
ESUAPNINEPO sesolc
)1(
tceffeon
)noitcnufdAgnidulcxe(
tceffeon
GNISOLC noitomsesrevernoitomsesrevertceffeon
GNINEPO spotstceffeongnimm
argorPees
DEPPOTS sesolc
)1(
tceffeon
)gnisolcstibihni(
tceffeon
TAB.2 LOGIC A (Automatic)
TAB.3 LOGIC E (Semi-automatic)
(1)
With pre-flashing selected, movement begins after pre-flashing time.
ENGLISH
14
8. ROTATION DIRECTION CHECK
Procedure for checking exact connection of motor phases:
1) Put the operator in manual mode
2) Manually take the door to its operating mid-point.
3) Stop the operator
4) Power up the system.
5) Send an opening pulse (OPEN) and check if the motor executes a door opening operation.
If the door closes, change over the phases of the electric motor on the terminal-board (black and brown cables) of the
board.
For two-operator applications, assign the same wire colours to the "COM,OP,CL" terminals, of the board and the Slave board,
and, if you have to change over the phases, change them over for both motors.
• The board carries out an electronic control (the connected motor must be present) before every start. If you
attempt to make the board operate without motor load or with an insufficient load, no power is supplied
at motor output.
• The courtesy light lights up when the motor starts and remains lighted for the programmed time, starting when
the movement has finished.
9. ADJUSTMENT OF ELECTRONIC CLUTCH (ANTI-CRUSHING)
The unit has a motor torque adjustment electronic system which, according to the setting, limits door thrust in the presence
of an obstacle. When the obstacle is removed, the door resumes moving until it reaches the limit-switch or the mechanical
stop.
We advise you to adjust the electronic clutch in conformity with current safety regulations.
10. ENCODER OPERATION
Thanks to encoder management, the GEO 07 control unit, if correctly installed, guarantees installation in compliance with
current safety regulations.
The encoder is active during both door opening and closing stages.
During the opening stage, the encoder stops door movement and positions the control unit in STOP status. At the first
opening command, the door executes a closing operation and resumes the memory-stored work cycle.
During the closing stage, the encoder reverses door motion until the door is completely open. If operating with an automatic
logic, the door closes when pause time has elapsed.
• Encoder intervention DOES NOT DISABLE automatic re-closing.
• The encoder is disabled by the intervention of one of the two limit-switches, enabling the door to recognise
the mechanical travel stop.
• Obstacle detection sensitivity is linked to the motor torque setting: the more motor power is increased, the
lower the encoder's detection sensitivity and vice-versa.
note - notes - note - notas - anmerkung - opmerkingen
GENIUS S.p.A.
Via Padre Elzi, 32
24050 - Grassobbio
BERGAMO-ITALY
tel. 0039.035.4242511
fax. 0039.035.4242600
www.geniusg.com
Le descrizioni e le illustrazioni del presente manuale non sono impegnative. GENIUS si riserva il diritto, lasciando inalterate le caratteristiche essenziali
dell’apparecchiatura, di apportare in qualunque momento e senza impegnarsi ad aggiornare la presente pubblicazione, le modifiche che essa ritiene
convenienti per miglioramenti tecnici o per qualsiasi altra esigenza di carattere costruttivo o commerciale.
The descriptions and illustrations contained in the present manual are not binding. GENIUS reserves the right, whils leaving the main features of the equipments
unaltered, to undertake any modifications to holds necessary for either technical or commercial reasons, at any time and without revising the present
publication.
Les descriptions et les illustrations du présent manuel sont fournies à titre indicatif. GENIUS se réserve le droit d’apporter à tout moment les modifications qu’elle
jugera utiles sur ce produit tout en conservant les caractéristiques essentielles, sans devoir pour autant mettre à jour cette publication .
Las descripciones y las ilustraciones de este manual no comportan compromiso alguno. GENIUS se reserva el derecho, dejando inmutadas las características
esenciales de los aparatos, de aportar, en cualquier momento y sin comprometerse a poner al día la presente publicación, todas las modificaciones que
considere oportunas para el perfeccionamiento técnico o para cualquier otro tipo de exigencia de carácter constructivo o comercial.
Die Beschreibungen und Abbildungen in vorliegendem Handbuch sind unverbindlich. GENIUS behält sich das Recht vor, ohne die wesentlichen Eigenschaften
dieses Gerätes zu verändern und ohne Verbindlichkeiten in Bezung auf die Neufassung der vorliegenden Anleitungen, technisch bzw, konstruktiv /
kommerziell bedingte Verbesserungen vorzunehmen.
De beschrijvingen in deze handleiding zijn niet bindend. GENIUS behoudt zich het recht voor op elk willekeurig moment de veranderingen aan te brengen
die het bedrijf nuttig acht met het oog op technische verbeteringen of alle mogelijke andere productie- of commerciële eisen, waarbij de fundamentele
eigenschappen van het apparaat gehandhaafd blijven, zonder zich daardoor te verplichten deze publicatie bij te werken.
Timbro rivenditore: / Distributor’s stamp: / Timbre de l’agent: /
Sello del revendedor: / Fachhändlerstempel: / Stempel dealer:
I0582 Rev.0
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
in altre lingue
- English: Genius GEO 07 Operating instructions
- français: Genius GEO 07 Mode d'emploi
- español: Genius GEO 07 Instrucciones de operación
- Deutsch: Genius GEO 07 Bedienungsanleitung
- Nederlands: Genius GEO 07 Handleiding
Documenti correlati
-
Genius GEO 07 Istruzioni per l'uso
-
-
Genius JA668 Istruzioni per l'uso
-
-
-
-
-
-
-
