HSM Classic 102.2 Manuale utente
- Categoria
- Trituratori di carta
- Tipo
- Manuale utente
PAPER SHREDDER
INSTRUCTION MANUAL
STANDARD PRODUCT WARRANTY
Quality is part of the company philosophy and all products are manufactured to the highest quality standards. All
technical data and measurements are approximate values and based upon single shift operations. All products are
subject to different limits and specifications due to operation length, paper size, grain, weight, misuse/abuse and power
configurations.
Prior to operation read the Manufacturer’s Operating Instructions included with this product. This will help ensure all
precautions are taken to avoid cancellation of the manufacturer’s warranty.
The manufacturer warrants that any new products sold will be free from defects in material and workmanship
when used under specified and normal operating conditions. This warranty is void if repairs are necessitated by
accidents, misuse, abuse, water damage or fire.
The capabilities of all products are in each specification flier. Exceeding model specifications causing product failure
is not covered by this warranty. Modifications, alterations and repairs must be performed by an authorized technician.
Lubrication for cross cut shredders is required every fifteen to thirty minutes of operation, to maintain top working
condition and this warranty.
Compact Shredders
Parts to repair any failure caused by defect is limited to one (1) year from date of invoice. Labor to repair any failure
caused by defect is limited to 180 days from date of invoice or warranty registration date.
NOTES:
• Freight or transportation damage is not classified as a warranty repair in any case.
• Proof of purchase invoice is required from the end-user for warranty validation or warranty registration date.
• All parts under warranty will be shipped and invoiced using standard costs and will be credited for the full amount only
when the defective part is returned.
• IT IS RECOMMENDED THAT A MAINTENANCE AGREEMENT BE UTILIZED TO SUPPLEMENT ALL WARRANTIES.
Cutting type Strip cut Cross cut
Shred size 1/4" 1/8" 1/16" 5/32" x 1"
Security level DIN 32757 – 1 2 2 3 3
Cutting capacity (sheet) DIN A4 70 g/m
2
16 - 18 13 - 15 8 - 9 6 - 7
Loading width 8.9"
Cutting speed 12 ft./min.
Voltage 115 V, 60 Hz
Power max. 150 W
Dimensions W x D x H 14.3" x 10.7" x 19.7"
Weight 14 lbs.
Volume of shreded material bag 6.6 gal.
Noise level (idle running) 58 - 60 dB (A)
SC: 1/4", 1/8"
2 3 4 51
2. Machine components / Technical Data
OPERATING INSTRUCTIONS
1. Cut material
container
2. Cutting head
3. Paper feeding opening
4. Automatic start stop control
5. Rocker switch
Technical and optical modications reserved.
ec
1. Proper use, warranty
We provide a warranty for the device in accordance with our general sales and
delivery terms. This warranty excludes wear, damage due to improper handling,
natural depreciation, and actions taken by third parties.
Shredding Capabilities:
5. Troubleshooting
Paper jam
You have fed in too much paper.
Caution!
Do not press rocker switch alternately forwards/backwards (pos. 1 /
pos. 2):
Cutting unit can be damaged.
• Press and hold down rocker switch pos. 2. Paper is pushed out.
• Separate paper stack.
• Press rocker switch pos. 1.
• Feed paper successively.
Shredded material container full
Empty the cut material container, because if it is too full, malfunctions
can occur in the cutting system.
• Press Automatic start stop control (4) 2 seconds.
• Switch equipment off; tap rocker switch pos. 2.
• Empty cut material container.
If other faults occur, please check the following before calling our customer
service:
• Is power plug inserted? è insert
• Is rocker switch turned on? è press rocker switch pos. 1
• Is the motor overloaded? è Allow motor to cool down for approx. 15-20
min.
2
1
2
2
3. Safety instructions
• Keep paper shredder out of the reach of children. If the shredder is damaged
or does not function properly, switch the device off, pull out the power plug and
inform our service engineers.
• This paper shredder should never be placed near or over a radiator or heat
source. The ventilation slots must not be blocked or covered.
• Make sure the power plug is easily accessible. Before plugging in the power
plug, check that the voltage and frequency of your local power supply
correspond to those stated on the type plate.
• Before changing the location or cleaning turn off and unplug the paper
shredder!
Risk of injury!
Do not reach into the paper feed slot.
Risk of injury by pulling in!
Keep long hair, loose articles of clothing, ties, scarves, jewelry
etc. away from feed opening. Material with the tendency to
form loops, e.g. tapes, strapping material, etc. must not be
shredded.
4. Putting into operation
Switching the paper shredder on
Press rocker switch pos. 1.
è Rocker switch locks in.
Feed paper
See “Technical data” for sheet capacity.
• Automatic start stop control starts the cutting system automatically
è Paper is pulled into cutting system and cut. When the paper feeding
opening is free again, the cutting system automatically switches off.
Switching paper shredder off
• Tap rocker switch pos. 2.
è Switch resets to zero position.
1
2
6. Cleaning and maintenance
Switch off the shredder, pull out the power plug.
When cleaning only use a soft cloth and a mild soap-water solution.
When the cutting capacity drops or the noise increases (Cross cut only):
• Spray special cutting blockoil through paper feed opening across the
whole width of the cutting system blades and press Automatic start
stop control (4).
• Run cutting system forwards and backwards (pos.1-pos.2) several
times without feeding paper. Paper dust and particles are shaken off.
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS
1
2
-
1
-
2
-
3
-
4
HSM Classic 102.2 Manuale utente
- Categoria
- Trituratori di carta
- Tipo
- Manuale utente
in altre lingue
- English: HSM Classic 102.2 User manual