Indesit IWC 71281ECOEU60HZ.R Guida utente

Categoria
Lavatrici
Tipo
Guida utente
1
GB
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 4
Cutting off the water or electricity supply
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and tips, 5
General safety
Disposal
Description of the washing machine
and starting a wash cycle, 6-7
Control panel
Indicator lights
Starting a wash cycle
Wash cycles, 8
Table of wash cycles
Personalisation, 9
Setting the temperature
Setting the spin speed
Functions
Detergents and laundry, 10
Detergent dispenser drawer
Preparing the laundry
Garments requiring special care
Load balancing system
Troubleshooting, 11
Service, 12
IWC 71281
Instructions for use
WASHING MACHINE
English,1
GB
IT
Italiano,13
2
GB
! This instruction manual should be kept in a safe
place for future reference. If the washing machine
is sold, transferred or moved, make sure that the
instruction manual remains with the machine so
that the new owner is able to familiarise himself/
herself with its operation and features.
! Read these instructions carefully: they contain
vital information relating to the safe installation
and operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its packaging.
2. Make sure that the washing machine has not
been damaged during the transportation process.
If it has been damaged, contact the retailer and do
not proceed any further with the installation process.
3. Remove the 4 pro-
tective screws (used
during transportation)
and the rubber wa-
sher with the cor-
responding spacer,
located on the rear
part of the appliance
(see figure).
4. Close off the holes using the plastic plugs
provided.
5. Keep all the parts in a safe place: you will need
them again if the washing machine needs to be
moved to another location.
! Packaging materials should not be used as
toys for children.
Levelling
1. Install the washing
machine on a flat stur-
dy floor, without resting
it up against walls,
furniture cabinets or
anything else.
2. If the floor is not
perfectly level, com-
pensate for any une-
venness by tightening
or loosening the adjustable front feet (see figure);
the angle of inclination, measured in relation to
the worktop, must not exceed 2°.
Levelling the machine correctly will provide it with
stability, help to avoid vibrations and excessive
noise and prevent it from shifting while it is ope-
rating. If it is placed on carpet or a rug, adjust the
feet in such a way as to allow a sufficient venti-
lation space underneath the washing machine.
Connecting the electricity and wa-
ter supplies
Connecting the water inlet hose
1. Connect the supply
pipe by screwing it to
a cold water tab using
a ¾ gas threaded con-
nection (see figure).
Before performing the
connection, allow the
water to run freely until
it is perfectly clear.
2. Connect the inlet
hose to the washing
machine by screwing
it onto the correspon-
ding water inlet of the
appliance, which is si-
tuated on the top right-
hand side of the rear
part of the appliance
(see figure).
3. Make sure that the hose is not folded over
or bent.
! The water pressure at the tap must fall within
the values indicated in the Technical details table
(see next page).
! If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
Installation
3
GB
Connecting the drain hose
Connect the drain
hose, without bending
it, to a drainage duct or
a wall drain located at a
height between 65 and
100 cm from the floor;
alternatively, rest it on
the side of a washba-
sin or bathtub, faste-
ning the duct supplied
to the tap (see figure).
The free end of the
hose should not be
underwater.
! We advise against the use of hose extensions;
if it is absolutely necessary, the extension must
have the same diameter as the original hose and
must not exceed 150 cm in length.
Electrical connections
Before plugging the appliance into the electricity
socket, make sure that:
•the socket is earthed and complies with all
applicable laws;
•thesocketisabletowithstandthemaximum
power load of the appliance as indicated in the
Technical data table (see opposite);
thepowersupplyvoltagefallswithinthevalues
indicated in the Technical data table (see opposite);
•thesocketiscompatiblewiththeplugofthe
washing machine. If this is not the case, repla-
ce the socket or the plug.
! The washing machine must not be installed
outdoors, even in covered areas. It is extremely
dangerous to leave the appliance exposed to
rain, storms and other weather conditions.
! When the washing machine has been installed,
the electricity socket must be within easy reach.
! Do not use extension cords or multiple sockets.
! The cable should not be bent or compressed.
! The power supply cable must only be replaced
by authorised technicians.
Warning! The company shall not be held responsible
in the event that these regulations are not respected.
The first wash cycle
Once the appliance has been installed, and
before you use it for the first time, run a wash
cycle with detergent and no laundry, using the
wash cycle 2.
65 - 100 cm
Technical data
Model
IWC 71281
Dimensions
width 59,5 cm
height 85 cm
depth 53,5 cm
Capacity
from 1 to 7 kg
Electrical
connections
please refer to the technical
data plate fixed to the machine
Water
connection
maximum pressure
1 MPa (10 bar)
minimum pressure
0.05 MPa (0.5 bar)
drum capacity 52 litres
Spin speed
up to 1200 rotations per
minute
Test wash
cycles in ac-
cordance with
regulations
1061/2010
and
1015/2010
Programme 6: Eco Cotton 60°.
Programme 6: Eco Cotton 40°.
This appliance conforms to
the following EC Directives:
- 2004/108/CE (Electroma-
gnetic Compatibility)
- 2012/19/EU - WEEE
- 2006/95/EC Low Voltage)
4
GB
Care and maintenance
Cutting off the water and electricity
supplies
•Turnoffthewatertapaftereverywashcycle.
This will limit wear on the hydraulic system in-
side the washing machine and help to prevent
leaks.
•Unplugthewashingmachinewhencleaningit
and during all maintenance work.
Cleaning the washing machine
The outer parts and rubber components of the
appliance can be cleaned using a soft cloth
soaked in lukewarm soapy water. Do not use
solvents or abrasives.
Cleaning the detergent dispenser
drawer
Remove the dispenser
by raising it and pulling
it out (see figure).
Wash it under running
water; this operation
should be repeated
frequently.
Caring for the door and drum of
your appliance
•Alwaysleavetheportholedoorajarinorderto
prevent unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-clea-
ning pump which does not require any mainte-
nance. Sometimes, small items (such as coins
or buttons) may fall into the pre-chamber which
protects the pump, situated in its bottom part.
! Make sure the wash cycle has finished and
unplug the appliance.
To access the pre-chamber:
1. using a screwdriver,
remove the cover pa-
nel on the lower front
part of the washing
machine (see figure);
2. unscrew the lid by
rotating it anti-clockwi-
se (see figure): a little
water may trickle out.
This is perfectly nor-
mal;
3. clean the inside thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks
are securely in place before you push it onto the
appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If there
are any cracks, it should be replaced immedia-
tely: during the wash cycles, water pressure is
very strong and a cracked hose could easily
split open.
! Never use second-hand hoses.
5
GB
Precautions and tips
! This washing machine was designed and constructed in
accordance with international safety regulations. The fol-
lowing information is provided for safety reasons and must
therefore be read carefully.
General safety
• Thisappliancewasdesignedfordomesticuseonly.
This appliance can be used by children aged
from 8 years and above and persons with re-
duced physical, sensory or mental capabilities
or lack of experience and knowledge if they
have been given supervision or instruction
concerning use of the appliance in a safe way
and understand the hazards involved. Children
shall not play with the appliance. Cleaning and
user maintenance shall not be made by children
without supervision.
• Donottouchthemachinewhenbarefootorwithwetor
damp hands or feet.
• Donotpullonthepowersupplycablewhenunpluggingthe
appliance from the electricity socket. Hold the plug and pull.
• Do not open the detergent dispenser drawer while the
machine is in operation.
• Donottouchthedrainedwaterasitmayreachextremely
high temperatures.
• Neverforcetheportholedoor.Thiscoulddamagethesafety
lock mechanism designed to prevent accidental opening.
• Iftheappliancebreaksdown,donotunderanycircum-
stances access the internal mechanisms in an attempt to
repair it yourself.
• Alwayskeepchildrenwellawayfromtheappliancewhile
it is operating.
• Thedoorcanbecomequitehotduringthewashcycle.
• Iftheappliancehastobemoved,workinagroupoftwo
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.
• Beforeloading laundryintothewashing machine,make
sure the drum is empty.
Disposal
• Disposingofthepackagingmaterials:observelocalregu-
lations so that the packaging may be re-used.
• TheEuropeanDirective2012/19/EU-WEEEonWasteElec-
trical and Electronic Equipment, requires that old household
electrical appliances must not be disposed of in the normal
unsorted municipal waste stream. Old appliances must
be collected separately in order to optimise the recovery
and recycling of the materials they contain and reduce the
impact on human health and the environment. The crossed
out “wheeled bin” symbol on the product reminds you of
your obligation, that when you dispose of the appliance it
must be separately collected.
Consumers should contact their local authority or retailer
for information concerning the correct disposal of their old
appliance.
6
GB
Detergent dispenser drawer: used to dispense
detergents and washing additives (see “Detergents and
laundry”).
ON/OFF button: switches the washing machine on and
off.
WASH CYCLE knob: programmes the wash cycles. Du-
ring the wash cycle, the knob does not move.
FUNCTION buttons with indicator light: used to select the
available functions. The indicator light corresponding to the
selected function will remain lit.
TEMPERATURE knob: sets the temperature or the cold
wash cycle (see “Personalisation”).
SPIN SPEED knob: sets the spin speed or exclude the
spin cycle completely (see “Personalisation”).
WASH CYCLE PROGRESS/DELAY TIMER
indicator
light
s: used to monitor the progress of the wash cycle.
The illuminated indicator light shows which phase is in
progress.
If the Delay Timer function has been set, the time remai-
ning until the wash cycle starts will be indicated (see next
page).
DOOR LOCKED indicator light: indicates whether the
door may be opened or not (see next page).
START/PAUSE button with indicator light: starts or tem-
porarily interrupts the wash cycles.
N.B. To pause the wash cycle in progress, press this
button; the corresponding indicator light will flash orange,
while the indicator light for the current wash cycle phase
will remain lit in a fixed manner. If the DOOR LOCKED
indicator light is switched off, the door may be opened
(wait approximately 3 minutes).
To start the wash cycle from the point at which it was inter-
rupted, press this button again.
Standby mode
This washing machine, in compliance with new energy
saving regulations, is fitted with an automatic standby
system which is enabled after a few minutes if no activity is
detected. Press the ON-OFF button briefly and wait for the
machine to start up again.
Description of the washing
machine and starting a wash cycle
WASH CYCLE PROGRESS/
DELAY TIMER indicator lights
DOOR LOCKED
indicator light
START/
PAUSE
button with
indicator light
Control panel
Detergent dispenser drawer
ON/OFF
button
WASH CYCLE
knob
TEMPERATURE
knob
FUNCTION
buttons with
indicator lights
SPIN SPEED
knob
7
GB
Indicator lights
The indicator lights provide important information.
This is what they can tell you:
Delayed start
IftheDELAYTIMERfunctionhasbeenactivated(see “Per-
sonalisation”), after the wash cycle has been started the
indicator light corresponding to the selected delay period
will begin to flash:
Astimepasses,theremainingdelaywillbedisplayedand
the corresponding indicator light will flash:
The set programme will start once the selected time delay
has expired.
Wash cycle phase indicator lights
Once the desired wash cycle has been selected and has be-
gun, the indicator lights switch on one by one to indicate which
phase of the cycle is currently in progress.
Function buttons and corresponding indicator lights
When a function is selected, the corresponding indicator
light will illuminate.
If the selected function is not compatible with the program-
med wash cycle, the corresponding indicator light will flash
and the function will not be activated.
If the selected function is not compatible with another
function which has been selected previously, the indicator
light corresponding to the first function selected will
flash and only the second function will be activated; the
indicator light corresponding to the enabled option will
remain lit.
Door locked indicator light
When the indicator light is on, the porthole door is locked
to prevent it from being opened; make sure the indicator
light is off before opening the door (wait approximately 3
minutes). To open the door during a running wash cycle,
presstheSTART/PAUSEbutton;thedoormaybeopened
once the DOOR LOCKED indicator light turns off.
Starting a wash cycle
1. SwitchthewashingmachineonbypressingtheON/OFFbutton.Allindicatorlightswillswitchonforafewseconds,then
theywillswitchoffandtheSTART/PAUSEindicatorlightwillpulse.
2. Load the laundry and close the door.
3.SettheWASHCYCLEknobtothedesiredprogramme.
4. Set the washing temperature (see “Personalisation”).
5. Set the spin speed (see “Personalisation”).
6. Measure out the detergent and washing additives (see “Detergents and laundry”).
7. Select the desired functions.
8.StartthewashcyclebypressingtheSTART/PAUSEbuttonandthecorrespondingindicatorlightwillremainlitinafixed
manner, in green.
Tocancelthesetwashcycle,pausethemachinebypressingtheSTART/PAUSEbuttonandselectanewcycle.
9.Attheendofthewashcyclethe indicator light will switch on. The door can be opened once the DOOR LOCKED
indicator light turns off (wait approximately 3 minutes). Take out your laundry and leave the appliance door ajar to make sure
the drum dries completely. Switch the washing machine off by pressing the ON/OFF button.
Wash
Rinse
Spin
Drain
End of wash cycle
8
GB
Wash cycles
Table of wash cycles
Cotton 20° (wash cycle 7) ideal for lightly soiled cotton loads. The effective performance levels achieved at cold temperatures,
which are comparable to washing at 40°, are guaranteed by a mechanical action which operates at varying speed, with repeated
and frequent peaks.
Express (wash cycle 11) this wash cycle was designed to wash lightly soiled garments quickly: it lasts just 15 minutes and
therefore saves both energy and time. By selecting this wash cycle (11 at 30°C), it is possible to wash different fabrics together
(except for wool and silk items), with a maximum load of 1,5 kg.
Sport Intensive (wash cycle 12) is for washing heavily soiled sports clothing fabrics (tracksuits, shorts, etc.); for best results,
we recommend not exceeding the maximum load indicated in the “Table of wash cycles”.
Sport Light (wash cycle 13) is for washing lightly soiled sports clothing fabrics (tracksuits, shorts, etc.); for best results, we
recommend not exceeding the maximum load indicated in the “Table of wash cycles”. We recommend using a liquid detergent
and dosage suitable for a half-load.
Special Shoes (wash cycle 14) is for washing sports shoes; for best results, do not wash more than 2 pairs simultaneously.
1) Test wash cycle in compliance with regulations 1061/2010: set wash cycle 6 with a temperature of 60°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments
which can be washed at 60°C. The actual washing temperature may differ from the indicated value.
2) Test wash cycle in compliance with regulations 1061/2010: set wash cycle 6 with a temperature of 40°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments
which can be washed at 40°C. The actual washing temperature may differ from the indicated value.
For all Test Institutes:
2) Long wash cycle for cottons: set wash cycle 6 with a temperature of 40°C.
3) Long wash cycle for synthetics: set wash cycle 5; with a temperature of 40°C.
* If you select programme and exclude the spin cycle, the machine will drain only.
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors such as
water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
Wash cycles
Description of the wash cycle
Max.
temp.
C)
Max.
speed
(rpm)
Detergents
Max. load (kg)
Residual
dampness %
Energy
consumption
kWh
Total water lt
Cycle
duration
Prewash
Wash
Fabric
softener
Daily
1
Cotton with prewash: extremely soiled whites. 90° 1200
7
- - - 170’
2
Cotton: extremely soiled whites. 90° 1200 -
7
- - - 160’
3
Coloured Cottons: lightly soiled whites and delicate colours. 40° 1200 -
7
- - - 90
4
Synthetics: heavily soiled resistant colours. 60° 1000 -
3,5
44 0,93 53 130’
5
Synthetics (3): lightly soiled resistant colours. 40° 1000 -
3,5
- - - 100’
6
Eco Cotton 60° (1): heavily soiled whites and resistant colours.
60° 1200 -
7
53 1,21 52,5 160’
6
Eco Cotton 40° (2): lightly soiled whites and delicate colours.
40° 1200 -
7
53 0,97 75 220’
7
Cotton 20°: lightly soiled whites and delicate colours. 20° 1200 -
7
- - - 170’
Special
8
Wool: for wool, cashmere, etc. 40° 800 -
1,5
- - - 70
9
Silk/Curtains: for garments in silk and viscose, lingerie. 30° 0 -
1
- - - 55
10 Jeans
40° 800 -
3
- - - 75
11
Express: to refresh lightly soiled garments quickly (not suitable for wool, silk and
clothes which require washing by hand).
30° 800 -
1,5
- - - 15
Sport
12 Sport Intensive
30° 600 -
3
- - - 85
13 Sport Light
30° 600 -
3
- - - 60
14 Special Shoes
30° 600 -
Max.
2 pairs
- - - 60
Partial wash cycles
Rinse - 1200 - -
7
- - - 36
Spin + Drain - 1200 - - -
7
- - - 10
Drain only *
- - - -
7
- - - 3’
9
GB
Setting the temperature
TurntheTEMPERATUREknobtosetthewashtemperature(seeTable of wash cycles).
The temperature may be lowered, or even set to a cold wash .
The washing machine will automatically prevent you from selecting a temperature which is higher than the maximum value
set for each wash cycle.
Setting the spin speed
Turn the SPIN SPEED knob to set the spin speed for the selected wash cycle.
The maximum spin speeds available for each wash cycle are as follows:
Wash cycles Maximum spin speed
Cottons 1200 rpm
Synthetics 1000 rpm
Wool 800 rpm
Silk drain only
The spin speed may be lowered, or the spin cycle can be excluded altogether by selecting the symbol .
The washing machine will automatically prevent you from selecting a spin speed which is higher than the maximum speed
set for each wash cycle.
Functions
The various wash functions available with this washing machine will help to achieve the desired results, every time.
To activate the functions:
1. Press the button corresponding to the desired function;
2. the function is enabled when the corresponding indicator light is illuminated.
Note:
- If the selected function is not compatible with the programmed wash cycle, the corresponding indicator light will flash and
the function will not be activated.
- If the selected function is not compatible with another function which has been selected previously, the indicator light
corresponding to the first function selected will flash and only the second function will be activated; the indicator light
corresponding to the enabled option will remain lit.
Selecting this option enables you to suitably adjust drum rotation, temperature and water to a reduced load of lightly soiled
cotton and synthetic fabrics (refer to the
“Table of wash cycles”
). “ ” enables you to wash in less time thereby saving
water and electricity. We suggest using a liquid detergent suitably measured out to the load quantity.
The function saves energy by not heating the water used to wash your laundry - an advantage both to the
environment and to your energy bill. Instead, intensified wash action and water optimisation ensure great wash results in the
same average time of a standard cycle.
For the best washing results we recommend the usage of a liquid detergent.
Extra rinse
By selecting this option, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is particularly
useful for sensitive skin.
Delay timer
This timer delays the start time of the wash cycle by up to 12 hours.
Press the button repeatedly until the indicator light corresponding to the desired delay time switches on. The fifth time the
button is pressed, the function will be disabled.
N.B.OncetheSTART/PAUSEbuttonhasbeenpressed,thedelaytimecanonlybemodifiedbydecreasingituntillaunching
the set programme.
Personalisation
10
GB
Detergents and laundry
Detergent dispenser drawer
Good washing results also depend on the correct dose of
detergent: adding too much detergent will not necessa-
rily result in a more efficient wash, and may in fact cause
build up on the inside of your appliance and contribute to
environmental pollution.
! Do not use hand washing detergents because these
create too much foam.
! Use powder detergent for white cotton garments, for pre-
washing, and for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
Open the detergent di-
spenser drawer and pour
in the detergent or washing
additive, as follows.
compartment 1: Pre-wash detergent (powder)
compartment 2: Detergent for the wash cycle
(powder or liquid)
Liquid detergent should only be poured in immediately
prior to the start of the wash cycle.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
Preparing the laundry
•Dividethelaundryaccordingto:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
•Emptyallgarmentpocketsandcheckthebuttons.
• Donotexceedthelistedvalues,whichrefertothe
weight of the laundry when dry: see “Table of wash
cycles”.
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g
Garments requiring special care
Wool: all wool garments can be washed using programme
8, even those carrying the “hand-wash only” label. For
best results, use special detergents and do not exceed
1,5 kg of laundry.
Silk: use special wash cycle 9 to wash all silk garments.
We recommend the use of special detergent which has
been designed to wash delicate clothes.
Curtains: fold curtains and place them in a pillow case or
mesh bag. Use wash cycle 9.
Jeans: Turn garments inside-out before washing and use
a liquid detergent. Use programme 10.
Load balancing system
Before every spin cycle, to avoid excessive vibrations and
to distribute the load in a uniform manner, the drum rotates
continuously at a speed which is slightly greater than the
washing rotation speed. If, after several attempts, the load
is not balanced correctly, the machine spins at a reduced
spin speed. If the load is excessively unbalanced, the
washing machine performs the distribution process instead
of spinning. To encourage improved load distribution and
balance, we recommend small and large garments are
mixed in the load.
1
2
3
11
GB
Troubleshooting
Yourwashingmachinecouldfailtowork.BeforecontactingtheTechnicalAssistanceCentre(see “Assistance”), make sure
that the problem cannot be solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not
take in water (the indicator light for
the first wash cycle stage flashes
rapidly).
The washing machine continuously
takes in and drains water.
The washing machine does not
drain or spin.
The washing machine vibrates a lot
during the spin cycle.
The washing machine leaks.
The “optionindicator lights and the
“start/pause” indicator light flash,
while one of the “phase in progress”
indicator lights and the “door lo-
ckedindicator light will remain lit in
a fixed manner.
There is too much foam.
Possible causes / Solutions:
• Theapplianceisnotpluggedintothesocketfully,orisnotmakingcontact.
• Thereisnopowerinthehouse.
• Thewashingmachinedoorisnotclosedproperly.
• TheON/OFFbuttonhasnotbeenpressed.
• TheSTART/PAUSEbuttonhasnotbeenpressed.
• Thewatertaphasnotbeenopened.
• Adelayedstarthasbeenset(see “Personalisation”).
• Thewaterinlethoseisnotconnectedtothetap.
• Thehoseisbent.
• Thewatertaphasnotbeenopened.
• Thereisnowatersupplyinthehouse.
• Thepressureistoolow.
• TheSTART/PAUSEbuttonhasnotbeenpressed.
• Thedrainhoseisnotfittedataheightbetween65and100cmfromthefloor
(see “Installation”).
• Thefreeendofthehoseisunderwater(see “Installation”).
• Thewalldrainagesystemisnotfittedwithabreatherpipe.
If the problem persists even after these checks, turn off the water tap, switch
theapplianceoffandcontacttheAssistanceService.Ifthedwellingisononeof
the upper floors of a building, there may be problems relating to water drainage,
causing the washing machine to fill with water and drain continuously. Special
anti-draining valves are available in shops and help to avoid this inconvenience.
• Thewashcycledoesnotincludedraining:somewashcyclesrequirethedrain
phase to be started manually.
• Thedrainhoseisbent(see “Installation”).
• Thedrainageductisclogged.
• Thedrumwasnotunlockedcorrectlyduringinstallation(see “Installation”).
• Thewashingmachineisnotlevel(see “Installation”).
Thewashingmachineistrappedbetweencabinetsandwalls(see “Installation”).
• Thewaterinlethoseisnotscrewedonproperly(see “Installation”).
• Thedetergentdispenserdrawerisblocked(forcleaninginstructions,see
“Care and maintenance”).
• Thedrainhoseisnotfixedproperly(see “Installation”).
• Switchoffthemachineandunplugit,waitforapproximately1minuteand
then switch it back on again.
Iftheproblempersists,contacttheTechnicalAssistanceService.
• Thedetergentisnotsuitableformachinewashing(itshoulddisplaythetext
“for washing machines” or “hand and machine wash”, or the like).
• Toomuchdetergentwasused.
12
GB
Service
Before calling for Assistance:
• Check whether you can solve the problem alone (see “Troubleshooting”);
• Restarttheprogrammetocheckwhethertheproblemhasbeensolved;
• Ifthisisnotthecase,contactanauthorisedTechnicalAssistanceCentreusingthetelephonenumberprovidedonthe
guarantee certificate.
! Alwaysrequesttheassistanceofauthorisedtechnicians.
Have the following information to hand:
• thetypeofproblem;
• theappliancemodel(Mod.);
• theserialnumber(S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the
front of the appliance by opening the door.
IT
13
Italiano
Sommario
Installazione, 14-15
Disimballo e livellamento
Collegamenti idraulici ed elettrici
Primo ciclo di lavaggio
Dati tecnici
Manutenzione e cura, 16
Escludere acqua e corrente elettrica
Pulire la lavabiancheria
Pulire il cassetto dei detersivi
Curare oblò e cestello
Pulire la pompa
Controllare il tubo di alimentazione dell’acqua
Precauzioni e consigli, 17
Sicurezza generale
Smaltimento
Descrizione della lavabiancheria e
avviare un programma, 18-19
Pannello di controllo
Spie
Avviare un programma
Programmi, 20
Tabella dei programmi
Personalizzazioni, 21
Impostare la temperatura
Impostare la centrifuga
Opzioni
Detersivi e biancheria, 22
Cassetto dei detersivi
Preparare la biancheria
Capi particolari
Sistema bilanciamento del carico
Anomalie e rimedi, 23
Assistenza, 24
Assistenza Attiva 7 giorni su 7
IT
LAVABIANCHERIA
IWC 71281
Istruzioni per l’uso
14
IT
Installazione
! È importante conservare questo libretto per
poterlo consultare in ogni momento. In caso
di vendita, di cessione o di trasloco, assicu-
rarsi che resti insieme alla lavabiancheria per
informare il nuovo proprietario sul funziona-
mento e sui relativi avvertimenti.
! Leggere attentamente le istruzioni: ci sono
importanti informazioni sull’installazione,
sull’uso e sulla sicurezza.
Disimballo e livellamento
Disimballo
1. Disimballare la lavabiancheria.
2. Controllare che la lavabiancheria non abbia
subìto danni nel trasporto. Se fosse danneg-
giata non collegarla e contattare il rivenditore.
3. Rimuovere le 4 viti
di protezione per il
trasporto e il gom-
mino con il relativo
distanziale, posti
nella parte posteriore
(vedi figura).
4. Chiudere i fori con i tappi di plastica in
dotazione.
5. Conservare tutti i pezzi: qualora la lava-
biancheria debba essere trasportata, dovran-
no essere
rimontati.
! Gli imballaggi non sono giocattoli per bam-
bini.
Livellamento
1. Installare la lavabiancheria su un pavimen-
to piano e rigido, senza appoggiarla a muri,
mobili o altro.
2. Se il pavimento
non fosse perfet-
tamente orizzonta-
le, compensare le
irregolarità svitando
o avvitando i piedini
anteriori (vedi figura);
l’angolo di inclina-
zione, misurato sul
piano di lavoro, non
deve superare i 2°.
Un accurato livellamento dà stabilità alla
macchina ed evita vibrazioni, rumori e spo-
stamenti durante il funzionamento. In caso di
moquette o di un tappeto, regolare i piedini in
modo da conservare sotto la lavabiancheria
uno spazio sufficiente per la ventilazione.
Collegamenti idraulici ed elettrici
Collegamento del tubo di
alimentazione dell’acqua
1. Collegare il tubo
di alimentazione
avvitandolo a un
rubinetto d’acqua
fredda con bocca
filettata da 3/4 gas
(vedi figura).
Prima di allacciare,
far scorrere l’acqua
finché non sia limpi-
da.
2. Collegare il tubo
di alimentazione alla
lavabiancheria
avvitandolo all’appo-
sita presa d’acqua,
nella parte posteriore
in alto a destra (vedi
figura).
3. Fare attenzione che nel tubo non ci siano
né pieghe né strozzature.
! La pressione idrica del rubinetto deve es-
sere compresa nei valori della tabella Dati
tecnici
(vedi pagina a fianco).
! Se la lunghezza del tubo di alimentazione
non fosse sufficiente, rivolgersi a un negozio
specializzato o a un tecnico autorizzato.
! Non utilizzare mai tubi già usati.
! Utilizzare quelli in dotazione alla macchina.
15
IT
Collegamento del tubo di scarico
Collegare il tubo di
scarico, senza pie-
garlo, a una condut-
tura di scarico o a
uno scarico a muro
posti tra 65 e 100
cm da terra;
oppure appoggiarlo
al bordo di un lavan-
dino o di una vasca,
legando la guida in
dotazione al
rubinetto (vedi figu-
ra). L’estremità libera
del tubo di scarico
non deve rimanere
immersa nell’acqua.
! È sconsigliato usare tubi di prolunga; se in-
dispensabile, la prolunga deve avere lo stes-
so diametro del tubo originale e non superare
i 150 cm.
Collegamento elettrico
Prima di inserire la spina nella presa della
corrente, accertarsi che:
la presa abbia la messa a terra e sia a nor-
ma di legge;
la presa sia in grado di sopportare il carico
massimo di potenza della macchina, indi
cato nella tabella Dati tecnici (vedi a fianco);
la tensione di alimentazione sia compresa
nei valori indicati nella tabella Dati tecnici
(vedi a fianco);
la presa sia compatibile con la spina della
lavabiancheria. In caso contrario sostituire
la presa o la spina.
! La lavabiancheria non va installata all’aper-
to, nemmeno se lo spazio è riparato, perché
è molto pericoloso lasciarla esposta a piog-
gia e temporali.
! A lavabiancheria installata, la presa della
corrente deve essere facilmente raggiungibile.
! Non usare prolunghe e multiple.
! Il cavo non deve subire piegature o com-
pressioni.
! Il cavo di alimentazione deve essere sostituito
solo da tecnici autorizzati.
Attenzione! L’azienda declina ogni responsabilità
qualora queste norme non vengano rispettate.
Primo ciclo di lavaggio
Dopo l’installazione, prima dell’uso, effettuare
un ciclo di lavaggio con detersivo e senza bian-
cheria impostando il programma 2.
65 - 100 cm
Dati tecnici
Modello
IWC 71281
Dimensioni
larghezza cm 59,5
altezza cm 85
profondità cm 53,5
Capacità
da 1 a 7 kg
Collegamen-
ti elettrici
vedi la targhetta caratteristi-
che tecniche applicata sulla
macchina
Collegamen-
ti idrici
pressione massima
1 MPa (10 bar)
pressione minima
0,05 MPa (0,5 bar)
capacità del cesto 52 litri
Velocità di
centrifuga
sino a 1200 giri al minuto
Programmi
di
controllo
secondo il
regolamento
1061/2010 e
1015/2010
programma 6;
Eco Cotone 60°C.
programma 6;
Eco Cotone 40°C.
Questa apparecchiatura è
conforme alle seguenti Diret-
tive Comunitarie:
- 2004/108/CE (Compatibili
Elettromagnetica)
- 2012/19/EU (WEEE)
- 2006/95/CE (Bassa Tensione)
16
IT
Escludere acqua e corrente elettrica
Chiudere il rubinetto dell’acqua dopo ogni
lavaggio. Si limita così l’usura dell’impianto
idraulico della lavabiancheria e si elimina il
pericolo di perdite.
Staccare la spina della corrente quando si
pulisce la lavabiancheria e durante i lavori
di manutenzione.
Pulire la lavabiancheria
La parte esterna e le parti in gomma possono
essere puliti con un panno imbevuto di acqua
tiepida e sapone. Non usare solventi o abra-
sivi.
Pulire il cassetto dei detersivi
Sfilare il cassetto sol-
levandolo e tirandolo
verso l’esterno (vedi
figura).
Lavarlo sotto l’acqua
corrente; questa
pulizia va effettuata
frequentemente.
Curare oblò e cestello
Lasciare sempre socchiuso l’oblò per evita-
re che si formino cattivi odori.
Pulire la pompa
La lavabiancheria è dotata di una pompa
autopulente che non ha bisogno di manuten-
zione. Può però succedere che piccoli ogget-
ti (monete, bottoni) cadano nella precamera
che protegge la pompa, situata nella parte
inferiore di essa.
! Assicurarsi che il ciclo di lavaggio sia termi-
nato e staccare la spina.
Per accedere alla
precamera:
1. rimuovere il pan-
nello di copertura
sul lato anteriore
della lavabiancheria
con l’ausilio di un
giravite (vedi figura);
2. svitare il coper-
chio ruotandolo in
senso antiorario
(vedi figura): è nor-
male che fuoriesca
un po’ d’acqua;
3. pulire accuratamente l’interno;
4. riavvitare il coperchio;
5. rimontare il pannello assicurandosi, prima
di spingerlo verso la macchina, di aver inseri-
to i ganci nelle apposite asole.
Controllare il tubo di alimentazio-
ne dell’acqua
Controllare il tubo di alimentazione almeno
una volta all’anno. Se presenta screpolature e
fessure va sostituito: durante i lavaggi le forti
pressioni potrebbero provocare improvvise
spaccature.
! Non utilizzare mai tubi già usati.
Manutenzione e cura
IT
17
Precauzioni e consigli
! La lavabiancheria è stata progettata e costruita in
conformità alle norme internazionali di sicurezza. Queste
avvertenze sono fornite per ragioni di
sicurezza e devono essere lette attentamente.
Sicurezza generale
Questo apparecchio è stato concepito esclusivamente
per un uso di tipo domestico.
Questo apparecchio può essere usato da
bambini da 8 anni in su e da persone con
capacità fisiche, sensoriali o mentali ridotte
o con esperienza e conoscenze insufficienti
se sono supervisionati o se hanno ricevu-
to adeguata formazione in merito all’uso
dell’apparecchio in modo sicuro e capendo
i pericoli connessi. I bambini non devono
giocare con l’apparecchio. Manutenzione
e pulizia non devono essere effettuati dai
bambini senza supervisione.
La lavabiancheria deve essere usata solo da persone
adulte e secondo le istruzioni riportate in questo libretto.
Non toccare la macchina a piedi nudi o con le mani o i
piedi bagnati o umidi.
Non staccare la spina dalla presa della corrente tirando
il cavo, bensì afferrando la spina.
Non aprire il cassetto dei detersivi mentre la macchina
è in funzione.
Non toccare l’acqua di scarico, che può raggiungere
temperature elevate.
Non forzare in nessun caso l’oblò: potrebbe danneg-
giarsi il meccanismo di sicurezza che protegge da
aperture accidentali.
In caso di guasto, in nessun caso accedere ai mecca-
nismi interni per tentare una riparazione.
Controllare sempre che i bambini non si avvicinino alla
macchina in funzione.
Durante il lavaggio l’oblò tende a scaldarsi.
Se dev’essere spostata, lavorare in due o tre persone
con la massima attenzione. Mai da soli perché la mac-
china è molto pesante.
Prima di introdurre la biancheria controlla che il cestello
sia vuoto.
Smaltimento
Smaltimento del materiale di imballaggio:
attenersi alle norme locali, così gli imballaggi potranno
essere riutilizzati.
La direttiva Europea 2012/19/EU - WEEE sui rifiuti di
apparecchia¬ture elettriche ed elettroniche (RAEE), preve-
de che gli elettrodo¬mestici non debbano essere smaltiti
nel normale flusso dei rifiuti solidi urbani. Gli apparecchi
dismessi devono essere raccolti separatamente per otti-
mizzare il tasso di recupero e riciclaggio dei materiali che
li compongono ed impedire potenziali danni per la salute
e l’ambiente. Il simbolo del cestino barrato è riportato
su tutti i prodotti per ricordare gli obblighi di raccolta se-
parata. Quando si acquista una nuova apparecchiatura
equivalente si può consegnare il RAEE al negoziante, che
è tenuto a ritirarlo gratuitamente; i RAEE di “piccolissime
dimensioni” (nessun lato sopra i 25 cm) possono essere
consegnati gratuitamente ai negozianti anche se non si
acquista nulla (solo nei negozi con superficie di vendita
superiore a 400 mq). Per ulteriori informazioni sulla corretta
dismissione degli elettrodomestici i detentori potranno
rivolgersi al servizio pubblico preposto o ai rivenditori.
18
IT
Pannello di controllo
Descrizione della lavabiancheria e
avviare un programma
Manopola
TEMPERATURA
Manopola
PROGRAMMI
Cassetto dei detersivi
SPIE AVANZAMENTO
CICLO/PARTENZA
RITARDATA
Tasti e spie
OPZIONE
Tasto ON/OFF
Manopola
CENTRIFUGA
Spia
OBLÒ
BLOCCATO
Cassetto dei detersivi: per caricare detersivi e additivi
(vedi “Detersivi e biancheria”).
Tasto ON/OFF: per accendere e spegnere la lavabian-
cheria.
Manopola PROGRAMMI: per impostare i programmi.
Durante il programma la manopola resterà ferma.
Tasti e spie OPZIONE: per selezionare le opzioni di-
sponibili. La spia relativa all’opzione selezionata rimarrà
accesa.
Manopola CENTRIFUGA: per impostare la centrifuga o
escluderla (vedi “Personalizzazioni”).
Manopola TEMPERATURA: per impostare la temperatu-
ra o il lavaggio a freddo (vedi “Personalizzazioni”).
SPIE AVANZAMENTO CICLO/PARTENZA RITAR-
DATA: per seguire lo stato di avanzamento del program-
ma di lavaggio.
La spia accesa indica la fase in corso.
Se è stata impostata l’opzione “Partenza Ritardata”,
indicheranno il tempo mancante all’avvio del programma
(vedi pagina a fianco).
Spia OBLÒ BLOCCATO: per capire se l’oblò è apribile
(vedi pagina a fianco).
Tasto e spia AVVIO/PAUSA: per avviare i programmi o
interromperli momentaneamente.
N.B.: per mettere in pausa il lavaggio in corso, premere
questo tasto, la spia relativa lampeggerà con colore
arancione mentre quella della fase in corso sarà accesa
fissa. Se la spia OBLÒ BLOCCATO sarà spenta, si
potrà aprire l’oblò (attendere 3 minuti circa).
Per far ripartire il lavaggio dal punto in cui è stato
interrotto, premere nuovamente questo tasto.
Standby
Questa lavatrice, in conformi alle nuove normative
legate al risparmio energetico, è dotata di un sistema di
autospegnimento (stand by) che entra in funzione dopo
circa 30 minuti nel caso di non utilizzo. Premere brevemente
il tasto ON-OFF e attendere che la macchina si riattivi.
Tasto e spia
AVVIO/
PAUSA
19
IT
Spie
Le spie forniscono informazioni importanti.
Ecco che cosa dicono:
Partenza ritardata
Se è stata attivata l’opzione “Partenza ritardata” (vedi “Per-
sonalizzazioni”), dopo avere avviato il programma, inizierà
a lampeggiare la spia relativa al ritardo selezionato:
Col trascorrere del tempo verrà visualizzato il ritardo resi-
duo con il lampeggio della spia relativa:
Trascorso il ritardo selezionato avrà inizio il programma
impostato.
Lavaggio
Risciacquo
Centrifuga
Scarico
Fine lavaggio
Spie fase in corso
Una volta selezionato e avviato il ciclo di lavaggio desi-
derato, le spie si accenderanno progressivamente per
indicarne lo stato di avanzamento:
Tasti opzione e relative spie
Selezionando un’opzione la spia relativa si illuminerà.
Se l’opzione selezionata non è compatibile con il pro-
gramma impostato la spia relativa lampeggerà e l’opzione
non verrà attivata.
Se l’opzione selezionata non è compatibile con un’altra
precedentemente impostata, la spia relativa alla prima
funzione selezionata lampeggerà e verrà attivata solo la
seconda, la spia dell’opzione attivata si illuminerà.
Spia oblò bloccato
La spia accesa indica che l’oblò è bloccato per impedire
l’apertura; per aprire l’oblò è necessario che la spia sia
spenta (attendere 3 minuti circa).
Per aprire l’oblò mentre un ciclo è in corso premere il
pulsante AVVIO/PAUSA; se la spia OBLÒ BLOCCATO è
spenta sarà possibile aprire l’oblò.
Avviare un programma
1. Accendere la lavabiancheria premendo il tasto ON/OFF. Tutte le spie si accenderanno per qualche secondo, poi si spegne-
ranno e pulserà la spia AVVIO/PAUSA.
2. Caricare la biancheria e chiudere l’oblò.
3. Impostare con la manopola PROGRAMMI il programma desiderato.
4. Impostare la temperatura di lavaggio (vedi “Personalizzazioni”).
5. Impostare la velocità di centrifuga (vedi “Personalizzazioni”).
6. Versare detersivo e additivi (vedi “Detersivi e biancheria”).
7. Selezionare le opzioni desiderate.
8. Avviare il programma premendo il tasto AVVIO/PAUSA e la spia relativa rimarrà accesa fissa di colore verde.
Per annullare il ciclo impostato mettere la macchina in pausa premendo il tasto AVVIO/PAUSA e scegliere un nuovo ciclo.
9. Al termine del programma si illuminerà la spia . Quando la spia OBLO’ BLOCCATO si spegnerà sarà possibile aprire
l’oblò (attendere 3 minuti circa). Estrarre la biancheria e lasciare l’oblò socchiuso per far asciugare il cestello.
Spegnere la lavabiancheria premendo il tasto ON/OFF.
20
IT
Programmi
Tabella dei programmi
Cotone 20° (programma 7) ideale per carichi in cotone sporchi. Le buone performance anche a freddo, comparabili con
un lavaggio a 40°, sono garantite da un’azione meccanica che lavora con variazione di velocità a picchi ripetuti e ravvicinati.
Express (programma 11) è studiato per lavare capi leggermente sporchi in poco tempo: dura solo 15 minuti e fa così
risparmiare energia e tempo. Impostando il programma (11 a 30°C) è possibile lavare insieme tessuti di diversa natura
(esclusi lana e seta) con un carico massimo di 1,5 kg.
Sport Intensive (programma 12) è studiato per lavare tessuti per abbigliamento sportivo (tute, calzoncini, ecc.) molto sporchi;
per ottenere i migliori risultati è consigliabile non superare il carico massimo indicato nella “Tabella dei programmi”.
Sport Light (programma 13) è studiato per lavare tessuti per abbigliamento sportivo (tute, calzoncini, ecc.) poco sporchi; per
ottenere i migliori risultati è consigliabile non superare il carico massimo indicato nella Tabella dei programmi”. Si raccomanda
di usare detersivo liquido, usare una dosa adatta a mezzo carico.
Sport Shoes (programma 14) è studiato per lavare scarpe sportive; per ottenere i migliori risultati non lavarne più di 2 paia.
1) Programma di controllo secondo il regolamento 1061/2010: impostare il programma 6 con una temperaura di 60°C.
Questo ciclo è adatto per pulire un carico di cotone normalmente sporco ed è il più efficiente in termini di consumo combinato di energia e di acqua, da usare su
capi lavabili a 60°. La temperatura effettiva di lavaggio può differire da quella indicata.
2) Programma di controllo secondo il regolamento 1061/2010: impostare il programma 6 con una temperaura di 40°C.
Questo ciclo è adatto per pulire un carico di cotone normalmente sporco ed è il più efficiente in termini di consumo combinato di energia e di acqua, da usare su
capi lavabili a 40°. La temperatura effettiva di lavaggio può differire da quella indicata.
Per tutti Test Institutes:
2) Programma cotone lungo: impostare il programma 6 con una temperatura di 40°C.
3) Programma sintetico lungo: impostare il programma 5 con una temperatura di 40°C.
La durata del ciclo indicata sul display o su questo libretto è una stima calcolata in base a condizioni standard. Il tempo effettivo può variare in base a numerosi fattori quali la temperatura e la
pressione dell’acqua in ingresso, la temperatura ambiente, la quantità di detersivo, la quantità ed il tipo di carico, il bilanciamento del carico, le opzioni aggiuntive selezionate.
Programmi
Descrizione del Programma
Temp.
max.
C).
Velocità
max.
(giri al
minuto)
Detersivi
Carico max.
(Kg)
Umidità
residua %
Consumo
energia kWh
Acqua
totale lt
Durata ciclo
Prela-
vaggio
Lavaggio
Ammor-
bidente
Daily
1
Cotone con prelavaggio: bianchi estremamente sporchi.
90° 1200
7
- - - 170’
2
Cotone: bianchi estremamente sporchi.
90° 1200 -
7
- - - 160’
3
Cotone Colorati: bianchi poco sporchi e colori delicati.
40° 1200 -
7
- - - 90
4
Sintetici: colori resistenti molto sporchi.
60° 1000 -
3,5
44 0,93 53 130’
5
Sintetici (3): colori resistenti poco sporchi.
40° 1000 -
3,5
- - - 100’
6
Eco Cotone (1): bianchi e colorati resistenti molto sporchi.
60° 1200 -
7
53 1,21 52,5 160’
6
Eco Cotone (2): bianchi poco sporchi e colori delicati.
40° 1200 -
7
53 0,97 75 220’
7
Cotone 20°: bianchi poco sporchi e colori delicati.
20° 1200 -
7
- - - 170’
Special
8
Lana: per lana, cachemire, ecc.
40° 800 -
1,5
- - - 70
9
Seta e tende: per capi in seta, viscosa, lingerie.
30° 0 -
1
- - - 55
10
Jeans
40° 800 -
3
- - - 75
11
Express: Per rinfrescare rapidamente capi poco sporchi (non indicato per la
lana, seta e capi da lavare a mano).
30° 800 -
1,5
- - - 15
Sport
12
Sport Intensive
30° 600 -
3
- - - 85
13
Sport Light
30° 600 -
3
- - - 60
14
Special Shoes
30° 600 -
Max.
2 paia
- - - 60
Parziali
Risciacquo
- 1200 - -
7
- - - 36
Centrifuga + Scarico
- 1200 - - -
7
- - - 10
Solo Scarico *
- - - -
7
- - - 3’
* Selezionando il programma ed escludendo la centrifuga la macchina effettuerà solo lo scarico.
1 / 1

Indesit IWC 71281ECOEU60HZ.R Guida utente

Categoria
Lavatrici
Tipo
Guida utente

in altre lingue